Power Supplies. SDN-C Compact DIN Rail Series

Transcription

1 SDN-C Compact DIN Rail Series The SDN-C DIN rail power supplies are the next generation of the popular SDN series. These models combine high effi ciency and compact size with new visual diagnostic LEDs to offer the most performance available from SolaHD. Essential industrial features such as Sag Immunity, Power Factor Correction, and universal voltage input have been retained in this series. Wide temperature operating range and parallel operation capability make the new SDN-C units suitable to a variety of industrial applications. Features Compact packaging to save space on the DIN rail New visual diagnostic LEDs for input and output status at a glance High MTBF means high reliability and long life Higher effi ciency saves energy and lowers amount of heat generated in panel PowerBoost TM overload capability to start high inrush loads Accepts Universal voltage Vac, 50/60 Hz input Single phase models meet SEMI F7 Sag Immunity standard Power Factor Correction (meets EN ) Class I, Div. 2 Hazardous Locations ATEX approval (pending) Patented DIN rail mounting clip User Adjustable output voltage accessible via front face Parallel capability standard Industrial grade design -25 o C to 60 o C operation without derating Rugged metal case and DIN connector User-friendly LEDs for status Large, rugged, accessible screw terminals Easy on/off DIN mounting Fully tested and burned-in at factory RoHS compliant Related Products SDN-P series SDP TM series SFL series SCP series SDU UPS UL 508 Listed IND. CONT. EQ. E61379 Applications Industrial Machine Control Process Control Conveying Equipment Material Handling Vending Machines Packaging Equipment Amusement Park Equipment Semiconductor Fabrication Equipment UL E CUL/CSA-C22.2 No. 23-M90 EMC and Low Volt. Directive contact Technical Services at (800) with any questions. 101

2 The SolaHD Difference Rugged metal packaging Multiple output connections for ease of wiring multiple devices New visual diagnostic LEDs show input and output status (see table below) Large, IP20-rated, screw terminals for #10 AWG/ mm 2, for quick, easy installation DC OK Relay Single or parallel use selectable by user Adjustable output voltage Clearly labeled front panel UL508 listing means no derating in UL 508 systems No internal fan, no extra cooling required in any power level Automatically adjusts for global Input voltages. No manual intervention required. Full CE compliance for safety, emissions and ingress protection New narrow width saves panel space LED Light Status Conditions Normal AC Power Loss AC Input Low No DC High Load Overload Hot Too Hot Input Green - Yellow Green Green Green Green Green Output Green - Green - Yellow Yellow Green - Alarm Red Yellow Red Yellow Yellow 102 contact Technical Services at (800) with any questions.

3 SDN-C Specifications (Single Phase) Catalog Number Description SDN C SDN C SDN C Input Nominal Voltage 115/230 Vac -AC Range Vac -DC Range Vdc -Frequency 3-67 Hz Nominal Current A A 6A / 3A -Inrush current max. Typ. < 15 A Typ.< 30 A < 0 A Efficiency (Losses 3 ) > 90% typ. (12 W) > 90% typ. (2 W) > 92% (38 W) Power Factor Correction Active power factor correction to better than 0.92 Output Nominal Voltage 2 V (23.5~28.5 Vdc Adj.) -Tolerance < ±2 % overall (combination Line, load, time and temperature related changes) Initial Voltage Setting 2.5V ± 1% -Ripple < 50 mvpp <100mVpp PARD PARD (Periodic and Random Deviation) = 100 mv peak-peak max Overvoltage Protection > 30.5 but < 33 Vdc, auto recovery Power Back Immunity < 35V Nominal Current 5 A (120 W) 10 A (20 W) 20 A (80W) -Peak Current Nominal Current for 2 seconds minimum while holding voltage > 20 Vdc -Short Circuit Current 1.5 x Nominal Current at near zero volts at short circuit condition -Current Limit PowerBoost Parallel Operation Switch selectable single unit or parallel unit operation. Units will not be damaged by parallel operation (regardless of switch position setting). Holdup Time >20 ms (Full load, 100 Vac T amb =+25 C) to 95% output voltage Voltage Fall Time <150 ms from 95% to 10% rated full load (T amb =+25 C) Line and Load Regulation < 0.5% EMC: -Emissions -Immunity Approvals Temperature 7 General EN :2001, EN :2001, Class B EN55011, EN55022 Radiated and Conducted including Annex. A, EN EN :2001, EN :2001, EN Level, EN Level 3, EN Level 3, EN Level input and level 3 output. EN Isolation class, EN , IEC voltage dip immunity standard UL508 Listed, culus; UL , curus; IEC ; Class I, Div. 2, Hazadous location approval; CE (LVD 73/23 & 200/108/EC), (EMC 89/336 & 93/68/EEC); EN Storage: -0 o C to + 85 o C, Operation -25 o C to +60 o C full power, with linear derating to half power from 60 to 70 o C (Convection cooling, no forced air required). Operation up to 50% load permissible with sideways or front side up mounting orientation. MTBF 6 > 550,000 hrs > 50,000 hrs Warranty 5 Years General Protection/Safety Protected against continuous short -circuit, continuous overload, continuous open circuit. Protection Class 1 (IEC536), degree of protection IP20 (IEC60529) Safe low voltage: SELV (acc. IEC ) Status Indicators Fusing -Input -Output Visual: 3 status LEDs (Input, Output, Alarm) Relay: N.O. contact rated 200ma/50 Vdc Installation Internally fused Outputs are capable of providing high currents for short periods of time for inductive load startup or switching. Fusing may be required for wire/loads if 2x Nominal O/P current rating cannot be tolerated. Continuous current overload allows for reliable fuse tripping. Simple snap-on to DIN TS35/7.5 or TS35/15 rail system. Mounting Connections Input: Screw terminals, connector size range: AWG (1.5-6 mm 2 ) for solid conductors. Output: Two terminals per output, connector size range: AWG (1.5-6 mm 2 ) for solid conductors. Case Fully enclosed metal housing with fi ne ventilation grid to keep out small parts. -Free Space 15 mm in front, 25 ~ 0 mm above and below, 10 mm left and right. H x W x D (inches/mm) ( ) ( ).88 x 3.2 x.98 (12 x 87 x 126.6) Weight (lbs/kg) 1.65 (0.75) 1.98 (0.9) 2.6 (1.2) 1. Not UL listed for DC input. 2. Input current ratings are conservatively specifi ed with low input, worst case effi ciency and power factor. 3. Losses are heat dissipation in watts at full load, nominal input line.. Ripple/noise is stated as typical values when measured with a 20 MHz, bandwidth scope and 50 Ohm resistor. 5. Peak current is calculated at 2 Volt levels. 6. Demonstrated through extended life test. 7. Contact tech support for operation at -25 o C. contact Technical Services at (800) with any questions. 103

4 C US LISTED SDN-C Series Dimensions W D Catalog Number Dimensions - inches (mm) H W D H VDC / 2.5 A OK 2-28 V Single Parallel OK NEC Class 2 Power Supply SOLA Power Supply SDN P SDN C.88 (12) 1.97 (50).55 (116) SDN C.88 (12) 2.36 (60).55 (116) SDN C.88 (12) 3.2 (87).98 (126.6) U L 115/230 VAC A 50/60 HZ N L SDN-C Series Mounting DIN Rail Mounting Snap on the DIN Rail: 1. Tilt unit slightly backwards 2. Put it onto the DIN Rail 3. Push downwards until stopped. Push at the lower front edge to lock 5. Shake the unit slightly to ensure that the retainer has locked Alternative Panel Mount: Using the optional SDN-PMBRK2 accessory, the unit can be screw mounted to a panel. Detachment from DIN Rail: 10 contact Technical Services at (800) with any questions.

5 SDN-C Series Mounting (cont.) Chassis Mounting Instead of snapping a Sola SDN unit on the DIN Rail, you can also attach it using the screw mounting set SDN-PMBRK2. Dimensions This set consists of two metal brackets, which replace the existing two aluminum profi les. contact Technical Services at (800) with any questions. 105