Installation Guide LiDCO Hemodynamic Monitor - Roll Stand Kit (US Version)
|
|
- Rosamond Harvey
- 5 years ago
- Views:
Transcription
1 Installation Guide LiDCO Hemodynamic Monitor - Roll Stand Kit (US Version) The purpose of this guide is to describe assembly of the roll stand kit and mounting of applicable devices. Table of Contents.0 Assembling the Roll Stand with Counterweight and Utility Basket Attaching the Roll Stand Handle Attaching the Power Outlet Strip Attaching the Syringe/Bag Holder Attaching the Sensor Interface Bracket/Cord Loop Hook Attaching the Manual Tilt /VESA Mounting Plate Assembly Mounting the PPC-50, POC-53 or POC-55 Platform on the Roll Stand Cable Management Adjusting Tilt and Tilt Tension Periodic Maintenance & Cleaning... DU-LC Rev C 6/4/06 GCX Corp. Page of
2 .0 Assembling the Roll Stand with Counterweight and Utility Basket Post, 44'' with 6'' Offset 2 Base 3 5/6-8 x '' Hex Head Cap Screw (HHCS) 4 5/6 Split Lock Washer 5 Roll Stand Washer, 2'' 6 Utility Basket, 6'' 7 Nylon Basket Clip Utility Basket Attachment 2 8 #8-32 x -/2'' Pan Head Machine Screw (PHMS) 2 9 #8-32 x Hex Nut Phillips screwdriver (not provided), /2'' wrench (not provided).. Attach two (2) Nylon Basket Clips to Wire Utility Basket in accordance with separate installation guide (DU-UT-0002). Insert two (2) #8-32 x -/2'' PHMS and #8-32 hex nuts in Basket Clips but do not tighten at this time. 2. Slide Basket Clips over bottom end of Roll Stand Post and insert Post in center of Roll Stand Base (below left). Lay assembly on its side. 3. Using a /2'' [3mm] wrench, fasten Post to Base using one () 5/6-8 x '' HHCS, with 5/6 lock washer, and 5/6 flat washer (below right). Post Basket Clips (2) #8-32 x -/2'' PHMS (2) #8-32 Hex Nuts (2) Base 5/6 Flat Washer 5/6 Lock Washer 5/6-8 x '' HHCS 4. Slide Basket to desired mounting position on Post and tighten two (2) Basket Clip screws to secure Basket. DU-LC Rev C 6/4/06 GCX Corp. Page 2 of
3 2.0 Attaching the Roll Stand Handle Roll Stand Handle 2 #0-32 x 9/6'' Pan Head Machine Screw (PHMS) 2 Phillips screwdriver (not provided).. Fasten Handle to Post with two (2) #0-32 x 9/6'' PHMS as shown below. #0-32 x 9/6'' PHMS (2) DU-LC Rev C 6/4/06 GCX Corp. Page 3 of
4 3.0 Attaching the Power Outlet Strip Installation Note: The Power Outlet Strip is an optional accessory and may not be included with this Roll Stand Kit. Power Outlet Strip 2 Front Clamping Block 3 Rear Clamping Block 4 #0-32 x 9/6'' Pan Head Machine Screw (PHMS) 2 Phillips screwdriver (not provided) Fasten Front Clamping Block to threaded mounting holes on rear of Power Outlet Strip with two (2) #8-32 x 3/4'' PHMS as shown below left. 2. Position Power Outlet Strip on Roll Stand Post and fasten Rear Clamping Block to Front Block with two #0-32 x 9/6'' PHMS (below right). #8-32 x 3/4'' PHMS (2) #0-32 x 9/6'' PHMS (2) Front Clamping Block Mounting Holes on Rear of Power Outlet Strip DU-LC Rev C 6/4/06 GCX Corp. Page 4 of
5 4.0 Attaching the Syringe/Bag Holder Syringe/Bag Holder 2 #0-32 x 9/6'' Pan Head Machine Screw (PHMS) 2 Phillips screwdriver (not provided).. Fasten Syringe/Bag Holder around Post with two (2) #0-32 x 9/6'' PHMS as shown below. #0-32 x 9/6'' PHMS (2 Syringe/Bag Holder DU-LC Rev C 6/4/06 GCX Corp. Page 5 of
6 5.0 Attaching the Sensor Interface Bracket/Cord Loop Hook Sensor Interface Bracket/Front Clamping Block Assembly 2 Cord Loop Hook/Rear Clamping Block Assembly 3 #0-32 x 9/6'' Pan Head Machine Screw (PHMS) 2 2 Phillips screwdriver (not provided).. Position Clamping Blocks (Bracket and Hook) at desired height on Roll Stand Post and fasten Rear Block to Front Block (below left) with two (2) #0-32 x 9/6'' PHMS. 2. Mount Sensor Interface by inserting four (4) mounting studs into slots in mounting bracket and sliding downward into locking position (below center). Sensor Interface #0-32 x 9/6'' PHMS (2 DU-LC Rev C 6/4/06 GCX Corp. Page 6 of
7 6.0 Attaching the Manual Tilt /VESA Mounting Plate Assembly Mounting Plate Assy. 2 #0-32 x 7/8'' Flat Head Machine Screw (FHMS) 3 3 Lever, Tilt 4 Screw Cover, Black Lexan 5 9/64'' Hex Wrench Phillips screwdriver (not provided), 9/64'' hex wrench (provided).. Align Mounting Plate Assembly toward front of Roll Stand and fasten to top of Post with three (3) #0-32 x 7/8'' FHMS as shown below. Installation Note: The Tilt Lever is a multi-position clamping lever that operates by lifting, rotating, and releasing the handle. 2. Remove backing from black Screw Cover and press Cover over screw heads as shown below center. #0-32 x 7/8'' FHMS (3) Screw Cover DU-LC Rev C 6/4/06 GCX Corp. Page 7 of
8 7.0 Mounting the PPC-50, POC-53 or POC-55 Platform on the Roll Stand The PPC-50 platform requires a Mounting Adapter (provided) for mounting on the Roll Stand. The POC-53 and POC-55 platform have a 75 x 75mm mounting pattern on the rear and only requires M4 x 20mm screws (provided) for mounting on the Roll Stand. Procedures for both types of platform are included in this section. Mounting Adapter 2 M4 x 0mm Pan Head Machine Screw (PHMS) 8 3 M4 x 20mm PHMS 4 Phillips screwdriver (not provided). Mounting the PPC-50 Platform. Locate four (4) threaded mounting holes on rear housing (below left). 2. Fasten Mounting Adapter to PPC-50 with four (4) M4 x 0mm PHMS as shown below right. M4 x 0mm PHMS (4) Threaded Mounting Holes (4) Mounting Adapter DU-LC Rev C 6/4/06 GCX Corp. Page 8 of
9 3. Thread two (2) M4 x 0mm PHMS into two (2) upper holes on Mounting Adapter (below left). Leave /4'' [6 mm] of thread exposed to allow screws to fit into slots in VESA Mounting Plate. 4. Guide two (2) upper screws into slots in VESA Mounting Plate (below right). Do not fully tighten these screws until instructed in Step 5. M4 x 0mm PHMS (2) VESA Mounting Plate 5. Thread two (2) M4 x 0mm screws into two (2) lower mounting holes (below left). Tighten all mounting screws. M4 x 0mm PHMS (2) DU-LC Rev C 6/4/06 GCX Corp. Page 9 of
10 Mounting the POC-53 and POC-55 Platforms. Thread two (2) M4 x 20mm PHMS into two (2) upper holes of the 75 x 75mm mounting pattern on the rear of the POC- 53 or POC-55 (below left). Leave /4'' [6 mm] of thread exposed to allow screws to fit into slots in VESA Mounting Plate. 2. Guide two (2) upper screws into slots in VESA Mounting Plate (below right). Do not fully tighten these screws until instructed in Step 3. M4 x 20mm PHMS (2) 3. Thread two (2) M4 x 20mm screws into two (2) lower mounting holes. Tighten all mounting screws. M4 x 20mm PHMS (2) DU-LC Rev C 6/4/06 GCX Corp. Page 0 of
11 8.0 Cable Management One () Cable Clip (below left) is provided for managing cables along Roll Stand Post. Place loose cables inside Clip and slide Clip onto Post (below right). Roll Stand Cable Clip Cable Clip Cables Slide onto Post 9.0 Adjusting Tilt and Tilt Tension Adjust tilt by loosening the Tilt Adjustment Lever (see Note below). Grasp the device and tilt to desired angle. Tighten Tilt Adjustment Lever to lock position. Adjust tilt tension by equally tightening or loosening two (2) Tilt Tension Screws with the 9/64'' hex wrench provided. Once overall tilt tension is set, use Tilt Adjustment Lever to fine tune/lock tilt position. Tilt Lever Tilt Tension Screws (2) Note: The Tilt Adjustment Lever is a multiposition clamping lever that operates by lifting, rotating, and releasing the handle. 0.0 Periodic Maintenance & Cleaning All fasteners associated with the mounting system should be inspected periodically and tightened as necessary. Cleaning the Mounting Assembly CAUTION: GCX makes no claims regarding the efficacy of the listed chemicals or processes as a means for controlling infection. Consult your hospital s infection control officer or epidemiologist. To clean or sterilize mounted devices or accessory equipment, refer to the specific instructions delivered with those products.. The mounting assembly may be cleaned with most mild, non-abrasive solutions commonly used in the hospital environment (e.g. diluted bleach, ammonia, or alcohol solutions). 2. The surface finish will be permanently damaged by strong chemicals and solvents such as acetone or trichloroethylene. 3. Steel wool or other abrasive material should never be used. 4. Damage caused by the use of unapproved substances or processes will not be warranted. It is recommended that you test any cleaning solution on a small area of the mounting assembly that is not visible to verify compatibility. 5. Never submerge or allow liquids to enter the mounting assembly. Wipe any cleaning agents off the mounting assembly immediately, using a water-dampened cloth. Dry all parts thoroughly after cleaning. DU-LC Rev C 6/4/06 GCX Corp. Page of
Installation Guide LiDCO Hemodynamic Monitor - Roll Stand Kit (EURO Version)
Installation Guide LiDCO Hemodynamic Monitor - Roll Stand Kit (EURO Version) The purpose of this guide is to describe assembly of the roll stand kit and mounting of applicable devices. Table of Contents.0
More informationInstallation Guide. Xprezzon Roll Stand
3875 Cypress Drive Petaluma, CA 94954 800.228.2555 707.773.1100 Fax 707.773.1180 www.gcx.com Installation Guide Xprezzon Roll Stand The purpose of this guide is to describe assembly of the Roll Stand and
More informationInstallation Guide Roll Stand Kit for Philips MP20/30 Monitor
Installation Guide Roll Stand Kit for Philips MP20/30 Monitor The purpose of this guide is to: 1. Describe attachment of Post to Base (page 2). 2. Describe attachment of the Utility Basket to the Roll
More informationInstallation Guide Roll Stand Kit 2''/5.1cm Diameter Post with Tilt/Swivel Mounting Plate, Handle, Utility Basket and 10lbs/4.
3875 Cypress Drive Petaluma, CA 94954 800.228.2555 707.773.1100 Fax 707.773.1180 www.gcx.com Installation Guide Roll Stand Kit 2''/5.1cm Diameter Post with Tilt/Swivel Mounting Plate, Handle, Utility Basket
More informationInstallation Guide Stack Mount Kit for Philips G5 and MP5/20/30/40/50/60/70 Monitor
Installation Guide Stack Mount Kit for Philips G5 and MP5/20/30/40/50/60/70 Monitor The purpose of this guide is to describe installation of the Stack Mount. Parts Reference The following parts and hardware
More informationInstallation Guide Folding L-Bracket with Display Mounting Extension and Keyboard Tray for M-Series or VHM Arm
3875 Cypress Drive Petaluma, CA 94954 800.228.2555 707.773.1100 Fax 707.773.1180 www.gcx.com Installation Guide Folding L-Bracket with Display Mounting Extension and Keyboard Tray for M-Series or VHM Arm
More informationInstallation Guide Philips MP2 IntelliVue M-Series Arm (12'' or 8'') Rail Mount Kit
Installation Guide Philips MP2 IntelliVue M-Series Arm (12'' or 8'') Rail Mount Kit The purpose of this guide is to: 1. Describe mounting of MP2 equipment on Mounting Bracket (page 2). 2. Describe mounting
More informationInstallation Guide GE Healthcare Carescape Single Display Roll Stand Kit
Installation Guide GE Healthcare Carescape Single Display Roll Stand Kit The purpose of this guide is to describe assembly of the Roll Stand. WARNING - EXCESSIVE LEAKAGE CURRENT - DO NOT use multiple socket
More informationInstallation Guide GE Healthcare Carescape Dual Display Roll Stand Kit
Installation Guide GE Healthcare Carescape Dual Display Roll Stand Kit The purpose of this guide is to describe assembly of the Roll Stand. WARNING - EXCESSIVE LEAKAGE CURRENT - DO NOT use multiple socket
More informationInstallation Guide. Philips IntelliVue MP20/30/40/50/60/70, MX400/450/600/700/800 Low Profile Camlock Mount
Installation Guide Philips IntelliVue MP20/30/40/50/60/70, MX400/450/600/700/800 Low Profile Camlock Mount The purpose of this guide is to: 1. Describe mounting of Philips Table Top Mount on Table Top
More informationInstallation Guide Philips MP90 Dual Display Mounting Kit for Dräger Apollo Anesthesia Machine
Installation Guide Philips MP90 Dual Display Mounting Kit for Dräger Apollo Anesthesia Machine The purpose of this guide is to describe installation of the Mounting Kit on the anesthesia machine. Parts
More informationGCX Mounting Assembly Installation Guide. Philips MP90 (M8010A) Mounting Kit for Drager Zeus
GCX Mounting Assembly Installation Guide Philips MP90 (M8010A) Mounting Kit for Drager Zeus The purpose of this guide is to: 1. Describe attachment of Down Post to Arm. 2. Describe attachment of Arm to
More informationInstallation Guide. Philips MP20/30/40/50 IntelliVue VHM Wall Mount Kit
Installation Guide Philips MP20/30/40/50 IntelliVue VHM Wall Mount Kit The purpose of this guide is to: 1. Describe attachment of Table Top Mount to Mounting Adapter. 2. Describe attachment of Mounting
More informationInstallation Guide Philips MP90 Mounting Kit with 16'' M-Series Arm for Datex Ohmeda Avance Anesthesia Machine
Installation Guide Philips MP90 Mounting Kit with 16'' M-Series Arm for Datex Ohmeda Avance Anesthesia Machine The purpose of this guide is to describe installation of the Mounting Kit on the anesthesia
More informationInstallation Guide VHM Wall Mount Kit for Philips MX600/700/800 and MP60/70 IntelliVue
Installation Guide VHM Wall Mount Kit for Philips MX600/700/800 and MP60/70 IntelliVue The purpose of this guide is to: 1. Describe attachment of Table Top Mount to Mounting Adapter (page 2). 2. Describe
More informationGCX Mounting Assembly Operation/Installation Manual
GCX Mounting Assembly Operation/Installation Manual Dräger Model Fabius GS with Dräger Vamos, CWS 15 "Recall" and GEMS IT DASH 3000/4000 Patient Monitor Option 1 Option 2 Option 3 Vamos or Dash 3000/4000
More informationInstallation Guide Variable Height Roll Cart for Corometrics/GE 250 Series Fetal Monitor with Dual Displays and Keyboard Mounts
3875 Cypress Drive Petaluma, CA 94954 800.228.2555 707.773.1100 Fax 707.773.1180 www.gcx.com Installation Guide Variable Height Roll Cart for Corometrics/GE 250 Series Fetal Monitor with Dual Displays
More informationInstallation Guide GE Mini Telemetry Receiver Rear Column Mount
3875 Cypress Drive Petaluma, CA 94954 800.228.2555 707.773.1100 Fax 707.773.1180 www.gcx.com Installation Guide GE Mini Telemetry Receiver Rear Column Mount Parts Reference The following parts and hardware
More informationInstallation Guide Corometrics/GE 250 Series Fetal Monitor Roll Cart with Laptop and Display Mounts
3875 Cypress Drive Petaluma, CA 94954 800.228.2555 707.773.1100 Fax 707.773.1180 www.gcx.com Installation Guide Corometrics/GE 250 Series Fetal Monitor Roll Cart with Laptop and Display Mounts Table of
More informationInstallation Guide VHM Arm Kit for Philips Heartstart MRx and Heartstart XL+
Installation Guide VHM Arm Kit for Philips Heartstart MRx and Heartstart XL+ The purpose of this guide is to: 1. Describe installation of Arm in channel (page 2). 2. Describe mounting of defibrillator
More informationInstallation Manual for Philips Intellivue MP5/20/30 VHM-25 Channel Mount Kit
3875 Cypress Drive Petaluma, CA 94954 800.228.2555 707.773.1100 Fax 707.773.1180 www.gcx.com Installation Manual for Philips Intellivue MP5/20/30 VHM-25 Channel Mount Kit Install Time: 10-15 minutes The
More informationInstallation Manual for Philips SureSigns VS3/VS4/VM4/VM6/VM8/VSV VHM-25 Countertop Mount
3875 Cypress Drive Petaluma, CA 94954 800.228.2555 707.773.1100 Fax 707.773.1180 www.gcx.com Installation Manual for Philips SureSigns VS3/VS4/VM4/VM6/VM8/VSV VHM-25 Countertop Mount Install Time: 20-30
More informationVHM-P (Non-Locking) Variable Height Arm with VESA Mounting Plate for 75 x 75mm or 100 x 100mm applications
3875 Cypress Drive Petaluma, CA 94954 800.228.2555 +1.707.773.1100 Fax 707.773.1180 www.gcx.com VHM-P (Non-Locking) Variable Height Arm with VESA Mounting Plate for 75 x 75mm or 100 x 100mm applications
More informationInstallation Manual for VHM-25 Series Arms Channel Mount
3875 Cypress Drive Petaluma, CA 94954 800.228.2555 707.773.1100 Fax 707.773.1180 www.gcx.com Installation Manual for VHM25 Series Arms Channel Mount Install Time: 1015 minutes The purpose of this manual
More information(Refer to qualified personnel)
3875 Cypress Drive Petaluma, CA 94954 800.228.2555 +1.707.773.1100 Fax 707.773.1180 www.gcx.com Installation Guide VHM-P (Non-Locking) and VHM-PL (Locking) Variable Height Arm (Slide-Above-Arm Configuration)
More information3875 Cypress Drive Petaluma, CA Fax
3875 Cypress Drive Petaluma, CA 94954 800.228.2555 +1.707.773.1100 Fax 707.773.1180 www.gcx.com VHM-P (Non-Locking) Variable Height Arm with Fixed Angle Front End for Flat Panel / Keyboard Bracket (L Brackets
More informationVHM-P (Non-Locking) and VHM-PL (Locking) Variable Height Arm with Slide-In Mounting Plate
3875 Cypress Drive Petaluma, CA 94954 800.228.2555 +1.707.773.1100 Fax 707.773.1180 www.gcx.com VHM-P (Non-Locking) and VHM-PL (Locking) Variable Height Arm with Slide-In Mounting Plate (Refer to qualified
More informationGE CARESCAPE Monitor B650 on VHM- PL Variable Height Arm Channel Mount with Vertical Position Lock
GE CARESCAPE Monitor B650 on VHM- PL Variable Height Arm Channel Mount with Vertical Position Lock PRODUCT DETAILS VHM-PL (Locking) Variable Height Arm with 14" / 35.6 cm Extension and Slide-In Mounting
More informationInstallation Guide. Philips MP90 M-Series Wall Mount Kit (12'' Pivot Arm) Section 1.0: Mounting the M-Series Arm Parts Reference...
Installation Guide Philips MP90 M-Series Wall Mount Kit (12'' Pivot Arm) The purpose of this guide is to describe installation of the MP90 M-Series Wall Mount Kit. Table of Contents Section 1.0: Mounting
More informationInstallation Guide Philips MP90 VHM Wall Mount Kit
Installation Guide Philips MP90 VHM Wall Mount Kit The purpose of this guide is to describe the procedures for installing the MP90 VHM Wall Mount Kit. Table of Contents Section 1.0: Mounting the VHM-Series
More informationGCX Mounting Assembly Installation Guide Philips MP90 (with AGM) Mounting Kit for Datex Ohmeda Aestiva Anesthesia Machine
GCX Mounting Assembly Installation Guide Philips MP90 (with AGM) Mounting Kit for Datex Ohmeda Aestiva Anesthesia Machine The purpose of this guide is to: 1. Describe mounting of the 7'' Channel. 2. Describe
More information3875 Cypress Drive Petaluma, CA Fax
3875 Cypress Drive Petaluma, CA 94954 800.228.2555 707.773.1100 Fax 707.773.1180 www.gcx.com GCX Mounting Assembly Installation Guide Datex-Ohmeda Aestiva Display Arm Mounting Kit for Philips IntelliVue
More informationCondor Manual. Corporation
Condor Manual Corporation PREFACE IMPORTANT, PLEASE READ CAREFULLY Thank you for your purchase with Amico Accessories Inc. This unit is designed for long lasting performance, providing the end user complies
More informationInstallation Instructions. ARS (Amico Rail Systems)
Installation Instructions ARS (Amico Rail Systems) w w w. a m i c o. c o m Preface Important, Please Read Carefully Thank you for your purchase with Amico Accessories Inc. This unit is designed for long
More informationUniversal Pitch Adjustable Wall Mount For Flat Panel Display UPM-2401
INSTALLATION INSTRUCTIONS Universal Pitch Adjustable Wall Mount For Flat Panel Display UPM-2401 Your new Chief Universal Pitch-Adjustable Wall Mount (UPM-2401) is a quick disconnect mounting system with
More informationINSTALLATION MANUAL FOR PILOT WORKSTATION
INSTALLATION MANUAL FOR PILOT WORKSTATION Weight Capacity: 5-25 lbs. Monitor Weight: 5-20 lbs. 6011180 Rev. B Contents Tools Required / Supplied Part Kits / Warnings/Disclaimer...2 Possible Base Mounting
More informationCarousel Unit User Manual Replacing the Check Stand Motor
Carousel Unit User Manual Replacing the Check Stand Motor 02/01/2017 1 Table of Contents Tools:... 3 Turn Off Power to the Unit:... 4 Remove Power Switch... 5 Remove Electric Eyes:... 6 Remove POS (Point-Of-Sale)
More informationINSTALLATION INSTRUCTIONS Small Flat Panel Extreme Pitch Mechanism Model: FSA-1006
INSTALLATION INSTRUCTIONS Small Flat Panel Extreme Pitch Mechanism Model: FSA-06 The FSA-06 Extreme Pitch Mechanism is an accessory kit for Small Flat Panel Display mounts. Specifications: fixed axis 90
More informationDriver Side Support Bracket pictured in "no-tow hook" direction. Reverse direction for tow hook equipped vehicles
PARTS LIST: 1 Bull Bar 2 10-1.5mm x 35mm Hex Bolts 2 Tube Brackets (Bull Bar) passenger or driver side 2 10mm Lock Washers 2 Upper Frame Brackets (models w/o tow hooks only) 4 10mm x 27mm OD x 3mm Flat
More informationINSTALLATION INSTRUCTIONS BULL BAR DODGE RAM 1500 PART # B-D1091;B-D2091
INSTALLATION INSTRUCTIONS PART # B-D1091;B-D2091 PARTS LIST: Qty Description Qty Description 1 Bull Bar 10 12mm Lock Washers 2 Upper Frame Brackets (for trucks without tow hooks only) 8 12-1.75mm Hex Nuts
More informationI-Sheet Number Rev.B 3-1/2 OVAL BULL BAR DODGE RAM 1500
PARTS LIST: 1 Bull Bar 2 10-1.5mm x 35mm Hex Bolts 2 Tube Brackets (Bull Bar) passenger or driver side 2 10mm Lock Washers 2 Upper Frame Brackets (models w/o tow hooks only) 4 10mm x 27mm OD x 3mm Flat
More informationInstallation Guide for EcoBrite EndLite LED Light Fixtures
Installation Guide for EcoBrite EndLite LED Light Fixtures BEFORE YOU BEGIN INSTALLATION Read these instructions carefully. Failure to follow these instructions will invalidate the warranty on this product.
More information(2) 10mm Quick Release Bolts with Pivot Washers (4) 10mm Flat Washers (2) 10mm Nylon Lock Nuts. (4) 10mm Plastic Washers
PARTS LIST: EXTREME GRILLE GUARD 1 Extreme Heavy Duty Grille Guard 2 10mm Cam Lever Quick Release Bolts with Special Pivot Washer 1 Driver/left Frame Mounting Bracket 4 10mm x 24mm OD x 2.2mm Flat Washers
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS DESCRIPTION: APPLICATION: PART NUMBER: Hood Bug Deflector Pathfinder T99D5 9PJ0A KIT CONTENTS: Item Qty. A 2 Inner Clip A B 2 Outer Clip B C 2 Wing Clip C D 1 Hood
More informationINSTALLATION INSTRUCTIONS RATTLER STEEL RUNNING BOARDS FORD TRANSIT VAN (FULL SIZE)
INSTALLATION INSTRUCTIONS PARTS LIST: 1 32-inch Steel Running Board 1 8-1.25mm x 35mm Hex Bolt 1 96-inch Steel Running Board 13 8-1.25mm x 25mm Hex Bolt 5 Passenger Side/Driver Side Mounting Brackets 20
More informationUniversal Pitch-Adjustable Wall Mount For Flat Panel Display PLP-91/D
INSTALLATION INSTRUCTIONS Universal Pitch-Adjustable Wall Mount For Flat Panel Display PLP-91/D Your new Wall Mount (PLP-91/D) is a quick disconnect mounting system with adjustability between 0 and 15
More informationPARTS LIST: ELEVATION BULL NOSE FRONT BUMPER FORD SUPERDUTY F
PARTS LIST: 1 Elevation Bumper Assembly 2 8-1.25mm x 25mm Hex Bolts 1 Winch Tray Bracket Assembly 2 8-1.25mm x 16mm Hex Bolts 2 3-hole Bracket Spacer Plates 6 8mm x 24mm x 2mm Flat Washers 2 Plastic Plugs
More informationInstallation Instructions
Installation Instructions SELECTRONIC Proximity Infection Control Faucet 0 / 0 / 0 Infection Control Faucet shown Installed on American Standard. Infection Control Sink Certified to comply with ASME A..M
More informationINSTALLATION INSTRUCTIONS GRILLE GUARD TOYOTA TUNDRA TOYOTA SEQUOIA PART # P2067
INSTALLATION INSTRUCTIONS GRILLE GUARD 07-14 TOYOTA TUNDRA 08-14 TOYOTA SEQUOIA PART # P2067 PARTS LIST: GRILLE GUARD 1 Grille Guard 2 10mm Cam Lever Quick Release Bolts with Special Pivot Washer 1 Driver/left
More informationALL PRODUCTS PATENT PENDING
1-of-5 7 Axis Ceiling Mount with Extendable Arm and Biased Pan and Tilt Head PN s 80104, 80104- Three different part numbers shown here with an 8 ceiling height & a 17 monitor 7 Axis Ceiling Mount with
More informationDown and Out Motor Mount Assembly & Installation Directions
Down and Out Motor Mount Assembly & Installation Directions Mounting the Down and Out Motor Mount correctly takes a lot of thought and a lot of planning. Please read the directions thoroughly and plan
More informationINSTALLATION INSTRUCTIONS
AUTOMOTIVE PRODUCTS, INSTALLATION INSTRUCTIONS Thrasher Board APPLICATION: 007-017 Chevy Silverado / GM Sierra / 1500-500-3500 Extended / Double / Crew Cab PART NUMBER: 8-8105, 8-81035 ITEM QUANTITY DESCRIPTION
More informationPlasma Dual Swing-Out (PDS Series) Wall Mount
INSTALLATION INSTRUCTIONS Plasma Dual Swing-Out ( Series) Wall Mount The wall mount is a rugged, versatile, and installer-friendly solution to unique display mounting requirements. In addition to providing
More informationMotion System Components Diagram. Note: #2 Mirror Cover and X-Axis Motor Cover have been removed for visibility. Maintenance.
Professional Laser System PLS3.75, PLS4.75, PLS6.75 and PLS6.150D Keeping the laser system clean will ensure the highest quality engraving. A clean laser system is the best performing laser system. The
More informationRollstar Shade Installation Instructions
Rollstar Shade Installation Instructions All Lifting Systems Inside or Outside Mount Thank you for purchasing your new Rollstar shade. It has been custom-made from the highest quality materials to the
More informationINSTALLATION MANUAL
INSTALLATION MANUAL 2563000 Parts List 1 Carrier weldment 2 Support arm assembly 1 Third brake light assembly 1 Light extension bracket 1 Spare tire adjustment plate 1 Spare tire mount plate 1 Female spade
More informationPFPDARM1 Product Illustration
PFPDARM1 Product Illustration page 1 of 17 PFPDARM1Components & Fasteners 1x 1x 4x 1 each 4x 3/32" (2.38mm) 3/16" (4.76mm) 1/8" (3.17mm) 8x 4x TOOLS REQUIRED Phillips Screwdriver 1/2" Wrench 1/2" Socket
More informationFOR SIT-STAND WORKSTATION
INSTALLATION MANUAL FOR SIT-STAND WORKSTATION Weight Capacity: 6.5-24.5 lbs. 6017180 Rev. B Contents Tools Required / Supplied Part Kits / Warnings/Disclaimers...2 Base Installation Clamp Mount Base Location...3
More informationINSTALLATION INSTRUCTIONS
AUTOMOTIVE PRODUCTS, INSTALLATION INSTRUCTIONS HDX DROP STEP APPLICATION: 2007-2017 Chevy Silverado / GM Sierra / 1500-2500-3500 Ext. / Double / Crew Cab PART NUMBER: 56-13715, 56-13725 ITEM QUANTITY DESCRIPTION
More informationRMK HANDLEBAR KIT P/N ; ; APPLICATION BEFORE YOU BEGIN KIT CONTENTS. Verify accessory fitment at Polaris.com.
RMK HANDLEBAR KIT P/N 2883835; 2883836; 2883837 APPLICATION Verify accessory fitment at Polaris.com. BEFORE YOU BEGIN Read these instructions and check to be sure all parts and tools are accounted for.
More informationSAFETY THIS PRODUCT IS FOR OFFROAD USE ONLY. ALL LIABILITY FOR INSTALLATION AND USE RESTS WITH THE OWNER.
SAFETY Your safety and the safety of others is very important. In order to help you make informed decisions about safety, we have provided installation instructions and other information. These instructions
More informationVOLKSWAGEN AMAROK 3 PIECE HARD TONNEAU COVER INSTALLATION INSTRUCTIONS
VOLKSWAGEN AMAROK 3 PIECE HARD TONNEAU COVER INSTALLATION INSTRUCTIONS Care Instructions: Clean Tonneau Cover with a mild detergent and water solution. Do not use abrasive cleaners or solvents. Place these
More informationFireHawk M7XT Ultra Elite XT Facepiece
FireHawk M7XT Ultra Elite XT Facepiece MAINTENANCE AND REPAIR MSA 411 (L) Rev. 0 MSA 2014 Prnt. Spec. 10000005389(I) Mat. 10147457 Doc. 10147457 Replacement Kits Push-to-Connect Slide-to-Connect FireHawk
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS R5 STEP BOARD APPLICATION: 2007-2017 Chevrolet Silverado / GMC Sierra Extended / Double / Crew Cab AUTOMOTIVE PRODUCTS, PART NUMBER: 28-51020, 28-51025, 28-51030, 28-51035 ITEM
More informationInstallation Instructions Bolt-On Fender Flares Ford F150 (09-12) Part #17394
Please read instructions entirely before installing this product. Hardware Included QTY Hardware Included QTY Bolt Kit Included QTY EXTRUSION 29.5ft ALCOHOL TOWELETTE 4 BLACK HEX BOLT 42 RETAINING CLIP.9mm
More informationINFINITY MULTA SERIES
ASSEMBLY ASSEMBLY INSTRUCTIONS INSTRUCTIONS ASSEMBLY INSTRUCTIONS INFINITY MULTA SERIES Workstations, WORKSTATIONS, desks, DESKS, and AND tables TABLES with WITH powered POWERED ADJUSTMENT adjustment PARTS
More informationCheck what you have received against the component checklist and hardware above.
SSS SSPW SSW SSPB SSB Component Checklist Installation Instructions SYSTEMA Systema Monitor Spring Arm HARDWARE Display Mounting Spacers (x4) 3/4mm Allen Keys Display Mounting Screws Arm Assembly VESA
More informationHD BULL NOSE FRONT BUMPER FORD SUPERDUTY F PARTS LIST:
PARTS LIST: 1 HD Bull Nose Bumper Assembly 1 Bumper Cover 1 Winch Tray Bracket Assembly 5 6mm Combo Button Head Bolts (cover) 2 3-hole Bracket Spacer Plates 1 Wrench (6mm Button Head) 2 Plastic Plugs for
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS DESCRIPTION: APPLICATION: Moonroof Wind Deflector Nissan Altima PART NUMBER: 999D UZ000 KIT CONTENTS: Item Qty. Description Service Part Number A B C D E F G H 1
More informationINSTALLATION INSTRUCTIONS Product Revision Form Rev. C INST-439 CRADLE, DELL E-6510/6500
7160-0202 Cradle is designed to be used with a Dell E-Port or E-Port Plus Port Replicator. The cradle is assembled for used with Dell E-6510. By removing 2 Side Spacers the Cradle can also be used with
More informationGeneral warnings and cautions
User guide English A 2 1 1 3 13 12 11 4 5 13 6 10 9 7 8 B C 14 16 17 15 18 19 Hospital Trolley User Guide ENGLISH Intended use The ResMed Hospital Trolley ( Trolley ) is designed to hold and move compatible
More informationINSTALLATION INSTRUCTIONS
INFINITI GENUINE PARTS INSTALLATION INSTRUCTIONS. DESCRIPTION:. APPLICATION: Hood Protector Chrome Nissan Armada (004) Nissan Titan (004) 3. PART NUMBER: 4. KIT CONTENTS: Item No. ) ) 3) 4) 5) 6) 7) 8)
More informationAND MAINTENANCE MANUAL
IMPORTANT File in your maintenance records COMPANION (SINGLE TOP TABLE) COMPANION II (SPLIT TOP TABLE) Companion & Companion II Overbed Tables OPERATIONS AND MAINTENANCE MANUAL For Parts or Technical Assistance
More informationINSTALLATION INSTRUCTIONS RATTLER STEEL RUNNING BOARDS DODGE RAM 1500 REGULAR CAB REGULAR CAB
INSTALLATION INSTRUCTIONS PARTS LIST: 2 Steel Running Boards 3 12mm Hex Nuts 1 Driver/Left Mounting Bracket 4 10-1.5mm x 35mm Hex Bolts 1 Driver/Left Support Bracket 4 10mm x 27mm OD x 3mm Flat Washers
More informationINSTALLATION INSTRUCTIONS Horizontal Array Pole Clamp Models: KTA-220/225 and KTA-320/325
INSTALLATION INSTRUCTIONS Horizontal Array Pole Clamp Models: KTA-220/225 and KTA-320/325 The KTA-220/225 and KTA-320/325 pivot arrays allow horizontal (yaw), vertical (pitch), and roll display adjustment.
More informationINSTALLATION INSTRUCTIONS
AUTOMOTIVE PRODUCTS, INSTALLATION INSTRUCTIONS ULTIMATE BULL BAR APPLICATION: 2009-2018 Dodge Ram 1500 (Excl. Rebel Model) 2019 Dodge Ram 1500 Classic PART NUMBER: 32-1960, 32-1965, 32-1960L, 32-1965L
More informationInstallation Instructions
Installation Instructions SELECTRONIC Hard-Wired, AC Powered Proximity Integrated Faucet with Above-Deck Mixing Flexible Selectronic Platform with Universal Sensor Easy installation. All electronics in
More informationPACIFICA Shower Cabin Installation Instructions
PACIFICA Shower Cabin Installation Instructions IMPORTANT Please read carefully the following instructions before installing your shower cabin. If you have any questions on this shower cabin installation
More informationMobile TV Mount Stand with Hydraulic Height Adjustment Model: DMS-172
Mobile TV Mount Stand with Hydraulic Height Adjustment Model: DMS-172 Instruction Manual Images may be different from actual product Disclaimer It is Dyconn s intention to have all the correct information
More information2 CYLINDER MOBILE CART ASSEMBLY INSTRUCTIONS
Parker Hannifin Corporation Precision Fluidics Division Porter Instrument 245 Township Line Road Hatfield, PA 9440 Office 25-723-4000/Fax 25-723-506 www.porterinstrument.com 2 CYLINDER MOBILE CART ASSEMBLY
More informationINSTALLATION INSTRUCTIONS
AUTOMOTIVE PRODUCTS, INSTALLATION INSTRUCTIONS HDX DROP STEP APPLICATION: 2015-2017 Ford F150 Super Cab / Super Crew 2017 Ford F250/350 Super Cab / Crew Cab PART NUMBER: 56-13935, 56-13945 CONTENT.ITEM
More information3PC TONNEAU COVER INSTALLATION INSTRUCTIONS. Ford Ranger/Mazda BT-50 (without bedliner)
3PC TONNEAU COVER INSTALLATION INSTRUCTIONS Ford Ranger/Mazda BT-50 (without bedliner) Care Instructions: Clean Tonneau Cover with a mild detergent and water solution. Do not use abrasive cleaners or solvents.
More informationonlinecomponents.com
COMPCT CONNECTOR TERMINL FOR REDUCED WIRING CT-2 CONNECTOR TERMINL ORDERING INFORMTION TYPES RoHS Directive compatibility information http://www.mew.co.jp/ac/e/environment/ CT2: CT-2 connector terminal
More informationINSTALLATION INSTRUCTIONS
AUTOMOTIVE PRODUCTS, INC. INSTALLATION INSTRUCTIONS ULTIMATE BULL BAR APPLICATION: 2017 Ford F-250/350 PART NUMBER: 32-3900, 32-3905, 32-3900L, 32-3905L ITEM QUANTITY DESCRIPTION TOOLS NEEDED 1 1 ULTIMATE
More informationINSTALLATION INSTRUCTIONS
AUTOMOTIVE PRODUCTS, INSTALLATION INSTRUCTIONS HDX XTREME BOARD APPLICATION: 2007-2017 Chevrolet Silverado / GMC Sierra 1500/2500/3500 Extended, Crew, Double Cab (Excludes Classic) PART NUMBER: 56-23715,
More informationINSTALLATION INSTRUCTIONS GRILLE GUARD TOYOTA TUNDRA TOYOTA SEQUOIA PART # 2067/2067-2
INSTALLATION INSTRUCTIONS 07-15 TOYOTA TUNDRA 08-15 TOYOTA SEQUOIA PART # 2067/2067-2 PARTS LIST: 1 Grille Guard 2 10mm Cam Lever Quick Release Bolts with Special Pivot Washer 1 Driver/left Frame Mounting
More informationA935 OWNER'S MANUAL ASSEMBLY INSTRUCTIONS
2013.02 A935 OWNER'S MANUAL ASSEMBLY INSTRUCTIONS A. SAFETY INSTRUCTIONS Read all cautions/warnings and obtain proper instruction on use of the machines prior to using. Use appropriate positioning and
More informationINSTALLATION INSTRUCTIONS
AUTOMOTIVE PRODUCTS, INSTALLATION INSTRUCTIONS HDX DROP STEP APPLICATION: 2007-2016 Chevy Silverado / GM Sierra / 1500-2500-3500 PART NUMBER: 56-13715, 56-13725 CONTENT ITEM QUANTITY DESCRIPTION TOOLS
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Trans4mer Grille Guard/Winch Mount For 2007 Toyota Tundra Kit 76380 (Black) and 76381 (Stainless) Your safety, and the safety of others, is very important. To help you make informed
More informationINSTALLATION INSTRUCTIONS RATTLER STEEL RUNNING BOARDS DODGE RAM 1500/ CREW CAB
INSTALLATION INSTRUCTIONS RATTLER STEEL RUNNING BOARDS PARTS LIST: 1 Driver/Left Steel Running Boards 5 12mm Lock Washers 1 Passenger/Right Steel Running Boards 5 12mm Hex Nuts 1 Driver/Left Mounting Bracket
More informationKit Part Number:
Equipped with AEM DRYFLOW Filter No oil required! Kit Part Number: 21-573 2006-2008 Toyota Yaris 1.5L *Legal in California only for racing vehicles which may never be used upon a highway. 2008, Advanced
More informationINSTALLATION INSTRUCTIONS
AUTOMOTIVE PRODUCTS, INSTALLATION INSTRUCTIONS R7 Step Board APPLICATION: 007-017 Chevy Silverado / GM Sierra / 1500-500-3500 Ext. / Double / Crew Cab PART NUMBER: 8-7100, 8-7105, 8-71030, 8-71035 ITEM
More informationUniversal Super Shield & Ultimate Aluminum w/electric Drive Conversion Kits , , Installation Instructions
WLH 09/19/16 111-0215 & 112-0215 607-0026 For technical support call us at (800) 368-3075 or visit our website at PullTarps.com. TABLE OF CONTENTS ***Assembly*** Conversion Kit-Universal Super Shield ***Wiring,
More informationWall Mount with a 7 axis extendable arm and a 75/100mm VESA Biased Screen Pan and Tilt Head PN s 80005, &
1-of-8 Display screen not included PN 80005 shown. Also available: 30 to 36 length - PN 80005-3036 36 to 42 length - PN 80005-3642 2-of-8 General Features This wall mount can be used as a universal support
More informationSYSTIMAX SMB-4-3/4, SMB-8-1/2 Shelf-Mounted Cable Bracket Kits and 1000G2-XCPB Expanded Cable Protector Kit
Instruction Sheet 860380799 SYSTIMAX Solutions SYSTIMAX SMB-4-3/4, SMB-8-1/2 Shelf-Mounted Bracket Kits and 1000G2-XCPB Expanded Protector Kit General The SYSTIMAX SMB-4-3/4 and SMB-8-1/2 shelf mounted
More informationTop Down Rollstar Shade Installation Instructions
Top Down Rollstar Shade Installation Instructions Thank you for purchasing your new Rollstar shade. It has been custom-made from the highest quality materials to the dimensions you specified. With proper
More informationInstallation Guide 4097M
Installation Guide 4097M Kargo Master Rancho Cordova, CA 95742 800 343 7486 CustomerService@KargoMaster.com DATE: Installation Instructions 4097M *PLEASE READ ALL INSTRUCTIONS AND WARNINGS PRIOR TO ASSEMBLING,
More information1 CMP throttle stud, two 3/8" nuts, a 3/8" bolt and corrector plate) CMP R4 Universal Cable 1
INSTRUCTIONS 370816 TCI TV Cable Bracket For Holley Carburetors Thank you for choosing TCI products; we are proud to be your manufacturer of choice. Please read this instruction sheet carefully before
More informationINSTALLATION INSTRUCTIONS
AUTOMOTIVE PRODUCTS, INSTALLATION INSTRUCTIONS HDX DROP STEP WTW APPLICATION: 2007-2017 Chevy Silverado / GM Sierra / 1500-2500-3500 Ext. / Double / Crew Cab - 6.5 Ft Bed PART NUMBER: 56-534575, 56-534595,
More informationINSTALLATION INSTRUCTIONS ELEVATION FRONT BUMPER 2018 FORD F150
INSTALLATION INSTRUCTIONS PARTS LIST: 1 Elevation Bumper Assembly 28 12mm x 37mm x 3mm Flat Washers 1 Driver/Left Frame Mounting Bracket 4 12mm Lock Washers 1 Passenger/Right Frame Mounting Bracket 12
More information