Universal Super Shield & Ultimate Aluminum w/electric Drive Conversion Kits , , Installation Instructions

Size: px
Start display at page:

Download "Universal Super Shield & Ultimate Aluminum w/electric Drive Conversion Kits , , Installation Instructions"

Transcription

1 WLH 09/19/ & For technical support call us at (800) or visit our website at PullTarps.com.

2 TABLE OF CONTENTS ***Assembly*** Conversion Kit-Universal Super Shield ***Wiring, Conversion Kits & Diagrams*** Mounting Positions... 1 Electric Motor Wiring & Plug Assembly... 7 Removing Tarp & Welding System to Truck... 2 Electric Motor & Breaker Wiring... 8 Dimple Tailgate & Weld Tarp Return Ramps... 3 Special Instructions for ED Electric Conversion Kit... 9 Rope Storage Hook Installation... 4 Special Instructions for Electric Drive Conversion Kit Optional Flap Tarp, Rope and Hook Installation... Bungee Cord Installation Housing Assembly for USS with Electric Drive Housing Assembly UA with Electric Drive For technical support call us at (800) or visit our website at PullTarps.com. i

3 Mounting Positions Step 1: Determine the mounting position for your truck Fig. 1 - Fig. 6. Fig. 1 Fig. 2 Fig. 3 "A" Mount "B" Mount "C" Mount Fig. 4 Fig. 5 Fig. 6 "D" Mount "E" Mount "F" Mount "B" Brackets NOTE: Use optional "B" Brackets when mounting in position "B" and "E". 1

4 Removing Tarp & Welding System to Truck Step 2A: Before welding remove tarp to avoid damage (Fig. 7A). To remove tarp slide the tarp out of the slotted end of the housing and remove from work area. NOTE: Remove Tarp Before Welding. Step 2B: Weld system mounting bar to truck as shown in Fig. 7B. Fig. 7B Fig. 7A Weld Mounting Bar to Truck System Assembly Fig. 8A & 8B Fig. 8A Fig. 8B 2

5 Dimple Tailgate & Weld Tarp Return Ramps Step 3: Dimple Tailgate for Rope Guide. Check the top of the tailgate where your tarp goes over for any obstructions that may interfere with the tarp laying flat all the way across the tailgate area. WARNING: Sharp Edges May Cut Tarp. Measure tailgate to find center and mark. Heat at mark with torch until area is red hot. Use a 3/4 diameter solid bar and lay it on the spot and strike it a few times. A smooth indentation should be left that will keep the rope centered (Fig. 9 & 10). Fig. 9 Fig. 10 Step 4. Weld on Tarp Return Ramps The Tarp Return Ramps hold the pullrod in place once the tarp has been deployed. The ramps should be welded as high as possible. See (Fig.11 & 12 for your application). Make sure all rough edges are ground smooth. If you have a raised hinge you will need to add a Hinged Ramp Gusset (NOT SUPPLIED) see (Fig.13). Fig. 11 Tarp Return Ramp Fig. 12 Tarp Return Ramp Fig. 13 Tarp Return Ramp Hinge Ramp Gusset 3

6 Rope Storage Hook Installation Step 5: Mount the rope as low as possible. The rope should come straight down and wrap around the center hook and then coil off to the side (Fig.14). When tarp is not in use, space the hooks far enough apart to store the full length of rope (Fig.15). Fig. 14 Rope Storage Hooks Fig. 15 Note: Tarp must be retracted when dumping Rope Storage Hooks 4

7 Optional Flap Tarp, Rope and Hook Installation Parts: Tie Down Hooks (Steel or Alum.) Pull Down Hook Fig. 16 Fig. 17 Note: The Location Of The Tie Down Hooks Is Critical! Step 6: Flip the braided rope over the corner so that the flaps and tie down ropes hang over each side of the box. The number of tie down hooks vary depending on the length of your tarp. One pull down hook is included with your Pulltarp system. If needed. Use the hook to pull the braided rope and flaps over the side of the box. The tie down hooks must be positioned so that: 1. The tie down rope can be reached from the ground. 2. The bungee cord has to be stretched to reach the last hook (see Step 7). 3. The rope has no slack. 4. The tie down hooks are level with one another. Fig. 18 Fig. 19 CORRECT INCORRECT To ensure proper hook placement, first duct tape the rope to the box in place of the tie down hooks. Start with hook closest to the cab. 1. Position the first hook 6 (15.24cm) down and 12 (30.48cm) forward (toward the cab) from the first grommet (Fig. 16). 2. Position 2nd hook straight down from 1st grommet. This hook should be reached from ground 3. (Fig. 17). 4. Place middle hooks equal distances from grommet (Fig. 18). These hooks should be placed at the same height as the second hook. 5. Position last hook (closest to the tailgate) below the last grommet at the same height as the others (Fig. 19). 6. Weld hooks in place. 5

8 Bungee Cord Installation Parts: 2 Bungee Cords 2 Oval Compression Sleeves 1 Snap Clip Step 7: After side hooks are installed, the tie down rope must be installed and cut to proper length. It is important to get all of the slack out of the rope to prevent blowing and rubbing of flaps in windy conditions. Tarps with Tie Downs Fig. 20 Snap Clip Installation Fig. 24 2nd Snap Clip Fig. 21 Tailgate 1st Snap Clip To tighten, pull loose end of rope through the Oval Compression Sleeve (Fig. 20). Stretch the bun gee cord making sure all slack is taken out of the rope, crimp compression sleeve (Fig. 21). Top View Flip the rope back on top of the tarp, making sure to hold the bu gee at all times. The first snap clip is factory installed 5-6 from the pullrod. Open the clip and enclose the rope. Weave the second clip through the main pullrope where the ends of the bungee cords meet the main pullrope. Make sure the rope is taught when clipped (Fig. 24). Note: First snap clip should not be used on long wheel base belly dumps Tarps with Side Flaps Fig. 22 Fig. 23 Excess Rope Connect Bungee Cord to Rope 1. Thread braided rope through Oval Compression Sleeve. 2. Feed rope through the eye of the bungee cord. 3. Thread the rope back through the oval compression sleeve. Adjust for proper length. Crimp co pression sleeve. To tighten, pull loose end of rope through the Oval Compression Sleeve (Fig. 22). Stretch the bungee cord making sure all slack is taken out of the rope, crimp compression sleeve (Fig. 23). Note: Check for proper placement of rope through the last two hooks. Fig. 25 You may need extra rope to keep the side flap sywstem ground operated. If your application requires extra rope, the slack needs to be taken up by a taching the end of the bungee cord to an alternate hook (Fig. 25). 6

9 Electric Motor Wiring & Plug Assembly Fig. 26 * Trailer Connector Detail Step 9 - Wiring: Assemble the Quick Disconnect as shown (Fig. 27). Battery 5/8" Breaker Step 8 - Wiring: First, remove motor housing, then run the 6 ga. wire to both locations (motor & battery box) and attach to truck body (Fig. 26). Note: The wire must go beyond the pivot point. Caution: Make sure wire does not get pinched at the pivot. Fig. 29 Trailer Connector* Fig. 30 Terminal #1 Dump Pivot Switch Fig. 27 Wire Fig. 28 Step 11 - Attaching The Connectors (Motor): 1. Split the molded 6 ga. wire approximately 4" and strip the ends about 5/8" down. 2. Attach connectors (part # ) and crimp (Fig. 29). 3. Attach black wire to Terminal #1 on motor (Fig. 30). 4. Attach red striped wire to Terminal #2 on motor (Fig. 30). Note: Wire Cutters required. Pin Connector Spring Tab Step 10: Crimp or solder pin to wire (Fig. 28). Note: Make sure the pin snaps over the end of the spring tab. 6 ga. 1/4" Lug Connector (part # ) Terminal #2 7

10 Electric Motor & Breaker Wiring 6 ga. 1/4" Lug Connector (part # ) 5/8" To motor Step 12: 1. Mount the Control Box at tailgate. 2. Spilt the 6 ga. wire at the Control Box about 4" back and slip on rubber boots Red Boot (part # ) on red striped wire and Black Boot (part # ) on black wire (Fig. 31 & 32). 3. Strip wire about 5/8"and attach connectors (part # ) (Fig. 31). 4. Attach Red Striped wire to Motor (+) and Black wire to Motor (-) on Control Box (Fig. 32). Note: Do not over tighten nuts on connections! Fig. 31 Fig ga. #10 terminal ends (Part # ) Step 13: 1. Mount breaker in the battery box away from moisture. 2. Cut a section in the red 6 ga. wire that will run to the postive terminal on the battery. 3. Strip wire the ends about 5/8" and attach 6 ga. #10 terminal ends (part # ) (Fig. 33). 4. Attach to breaker. Battery Fig. 34 Battery Aux 14 ga. wire Light 30 Amp "Non Cycle" Breaker Note: Mount as close as possible to power supply. To reset, disconnect power. 6 ga. wire Fig. 32 Wiring Diagram (Fig. 34) - To Ground Motor Forward & Reverse Switch 6 ga. wire 14 ga. wire Motor 25 Amp Push To Reset Circuit Breaker Motor check out procedure: 1. Remove leads from motor & attach volt meter to the leads. 2. With the switch in the on position, the volt meter should read 12 volts minimum. If voltage is low recheck with engine running. Recheck wiring and connections (minimum 6 gauge wire must be used). 3. Return switch to the neutral position & reattach leads to motor. 4. Attach volt meter to leads at the motor. 5. With the switch in the on position and the leads attached, the volt meter should read 8.5 volts minimum. If voltage is low recheck with engine running. Recheck wiring and connections (minimum 6 gauge wire must be used). 6. Return switch to the neutral position and attach amp meter to leads at the motor. 7. With the switch in the on position, amp meter should read approximately amps. Constant amperage reading of over 40 amps indicated binding in the system and/or low voltage. 8

11 Special Instructions for ED Electric Conversion Kit (Conversion Kit to add electric Drive to existing housing) Step A. Removing the Spring Remove the 7/16 bolt covering the access hole in the ratchet cover. Pull the tarp all the way out, secure to the tailgate. Insert a 3/8 x 3 bolt through the hole in the ratchet cover plate and into the groove in the roller tube (Fig. 1A). Step B. Remove Tarp from Housing Slide the tarp out of the roller tube through the slotted end plate (opposite side as ratchet) (Fig. 1A). Fig. 1A To To Disengage Lever, Increase Tension Remove Ratchet Lock & 1. Pull tarp out as far as Insert Screwdriver Here possible and tie off at tailgate 2. Remove Ratchet Lock. Turn ratchet nut clockwise 5 turns at at time. 3. Test operation and repeat steps 1 through 3 if necesary. To Decrease Tension: WARNING: 1. Remove Ratchet Lock. Place box Physical harm could occur if end wrench on all tension is not ratchet nut. Turn removed before ratchet nut slighty removing this plate. to the right and don t let go. 2. Insert screwdriver to disengage lever. Hold wrench with both hands and slowly unwind spring pressure. 3. When desired tension is achieved, remove screw driver allowing release lever to reengage ratchet gear. 4. Reinstall the Install Ratchet Lock here Rachet Lock. BY Ratchet Cover Plate Insert 3/8" Bolt Step C. Releasing the Spring Tension on the Roller Assembly 1. With a 3/4 box end wrench, turn the ratchet nut clockwise just far enough to relieve tension on the ratchet dog (Fig. 2A). 2. Place flat blade screwdriver on top of the ratchet dog to disengage it from the ratchet gear. 3. With both hands, turn the wrench counter clockwise to remove all of the tension from the spring. Do not let go of wrench! (be sure all of the tension has been released). Step D. Removing the Ratchet Cover Plate Remove the four screws from the ratchet cover plate and carefully take the plate off. Step E. Remove the Roller Tube Pull the entire roller tube assembly out the side of the housing (Fig. 3A). Step F. Removing the Spring Assembly 1. Remove the retaining screw from the end cap. 2. Place a piece of cardboard on the ground and hold the roller assembly vertically, with the ratchet assembly towards the ground. 3. Shake the roller assembly up and down above the cardboard to pop the end cap and spring assembly free from the roller tube (Fig. 4A). The card board is to protect the end of the spring shaft when it breaks free. Fig. 2A Fig. 3A Fig. 4A 9

12 Special Instructions for ED Electric Conversion Kit (Conversion Kit to add electric Drive to existing housing) Step G: Install Roller End Cap Before installing the Roller End Cap, the Roller Tube may need to be cut to to fit into the housing properly. Cut tube an additional 3/8 (Fig. 5A). Step H: Dimple the Roller Tube Once Roller End Cap is in Roller Tube, Dimple the end of the Roller Tube into the grove of the Roller End Cap with a flat head screw driver in three places (Fig. 6A). Fig. 5A Fig. 6A Dimple 3/8" Roller End Cap Roller Tube Step I: Universal Super Shield Install motor as shown below (Fig. 7A). Step J: Tarp Installation Slide Tarp into groove on Roller Tube and center (Fig. 8A). Part# EHW35 (3 REQ.) 5/16-18 X 1 HHCS BOLT Part# EHW34 (1 REQ.) 5/16-18 X 1 3/4 HHCS BOLT Fig. 7A Fig. 8A Part# P65/16LW (3 REQ.) 5/16 LOCK WASHER Part# P4AD1 (1 REQ.) ADAPTOR PLATE Part# 31 (1 REQ.) 5/16-18 NYLOCK NUT NOTE: See Switch Kit for Wiring Instructions. 10

13 Special Instructions for Electric Drive Conversion Kit Step A. Removing the Spring Remove the 7/16 bolt covering the access hole in the ratchet cover. Pull the tarp all the way out, secure to the tailgate. Insert a 3/8 x 3 bolt through the hole in the ratchet cover plate and into the groove in the roller tube (Fig. 1B). Step B. Remove Tarp from Housing Slide the tarp out of the roller tube through the slotted end plate (opposite side as ratchet) (Fig. 1B). Fig. 1B To To Disengage Lever, Increase Tension Remove Ratchet Lock & 1. Pull tarp out as far as Insert Screwdriver Here possible and tie off at tailgate 2. Remove Ratchet Lock. Turn ratchet nut clockwise 5 turns at at time. 3. Test operation and repeat steps 1 through 3 if necesary. To Decrease Tension: WARNING: 1. Remove Ratchet Lock. Place box Physical harm could occur if end wrench on all tension is not ratchet nut. Turn removed before ratchet nut slighty removing this plate. to the right and don t let go. 2. Insert screwdriver to disengage lever. Hold wrench with both hands and slowly unwind spring pressure. 3. When desired tension is achieved, remove screw driver allowing release lever to reengage ratchet gear. 4. Reinstall the Install Ratchet Lock here Rachet Lock. BY Ratchet Cover Plate Insert 3/8" Bolt Step C. Releasing the Spring Tension on the Roller Assembly 1. With a 3/4 box end wrench, turn the ratchet nut clockwise just far enough to relieve tension on the ratchet dog (Fig. 2B). 2. Place flat blade screwdriver on top of the ratchet dog to disengage it from the ratchet gear. 3. With both hands, turn the wrench counter clockwise to remove all of the tension from the spring. Do not let go of wrench! (be sure all of the tension has been released). Step D. Removing the Ratchet Cover Plate Remove the eight screws from the ratchet end plate and remove (Fig. 3B). Step E. Remove the Roller Tube Pull the entire roller tube assembly out the side of the housing (Fig. 3B). Step F. Removing the Spring Assembly A. Remove the retaining screw from the end cap. B. Place a piece of cardboard on the ground and hold the roller assembly vertically, with the ratchet assembly towards the ground. C. Shake the roller assembly up and down above the cardboard to pop the end cap and spring assembly free from the roller tube (Fig. 4B). The card board is to protect the end of the spring shaft when it breaks free. Fig. 2B Fig. 3B Fig. 4B 11

14 Special Instructions for Electric Drive Conversion Kit Step G: Install Roller End Cap Before installing the Roller End Cap, the Roller Tube may need to be cut to to fit into the housing properly. Cut tube an additional 7/8 (Fig. 5B). Step H: Dimple the Roller Tube Once Roller End Cap is in Roller Tube, Dimple the end of the Roller Tube into the grove of the Roller End Cap with a flat head screw driver in three places (Fig. 6B). Fig. 5B Fig. 6B Dimple 7/8" Roller End Cap Roller Tube Step I: Universal Super Shield Install motor as shown below (Fig. 7B). Fig. 7B Step J: Tarp Installation Slide Tarp into groove on Roller Tube and center (Fig. 8B). Fig. 8B NOTE: See Switch Kit for Wiring Instructions. 12

15 Housing Assembly for Universal Super Shield With Electric Drive ITEM PART # DESCRIPTION QTY XX SS Housing 9.5" x 80,84,87,89,93,96,100"lg XX Roller Tube Assy 80,84,87,89,93,96,100"lg XX Mounting Bar-Steel, 40,42,43.5,44.5,46.5,48,50"lg /4" Flat Washer USS /16"-18 x 1 3/4"lg. HHCS Bolt /16"-18 x 1"lg. HHCS Bolt /16"-18 x 1/2"lg. HHCS Bolt /16" Lock Washer /16"-18 Nyloc Nut #10-32 x 1/2"lg. Phillips Head Pan Alum. Adaptor Plate - SW Motor System End Plate Stud Kit " Large Steel Mounting Bracket V DC Electric Motor GA. Electric Wire (Not Shown) 100' Gray Quick Disconnect (Not Shown) Pulltarps Decal 1 REV: 11/08/07 BAB Pullrod Hardware ITEM PART # DESCRIPTION QTY Tarp Return Ramps (Steel) Tarp Return Ramps (Alum.) Rope Storage Kits (4 Steel Hooks) Rope Storage Kits (4 Alum. Hooks) XX Pull Rope (20, 25, 30, 35, 40, 50') 1 19 Determined by Length Pullrod (85, 91, 93, 96, 100, 105" Lengths) Pullrod Hardware Kit

16 Housing Assembly Ultimate Aluminum with Electric Drive ITEM PART # DESCRIPTION QTY XX Ultimate Aluminum Housing - 80, 84, 87, 89, 93, 96"lg XX Roller Tube - 80, 84, 87, 89, 93, 96"lg XX Mounting Bar - 40, 42, 43.5, 44.5, 46.5, 48, 50" lg. (Specify Steel or Aluminum) XX 6" large Steel Mounting Bar (Specify Steel or Aluminum) Elec. Ultimate Aluminum End Plate - Left Side Ultimate Aluminum End Plate - Right Side System End Plate Stud Kit Flanged End Cap Roller Drive Aluminum End Cap Screw #8-18 x 3/4" Self Drilling /16"-18 x 1"lg. HHCS Bolt /4"-20 x 1/2"lg. SS BHCS /16"-18 Nyloc Nut /16"-18 x 1 3/4 Hex Bolt /4" Flat Washer USS /16" Lock Washer /16"-18 x 1/2"lg. HHCS Bolt Pulltarps Decal V DC Electric Motor 1 Pullrod Hardware REV: 09/19/16 WLH ITEM PART # DESCRIPTION QTY Tarp Return Ramps (Steel) Tarp Return Ramps (Alum.) Rope Storage Kits (4 Steel Hooks) Rope Storage Kits (4 Alum. Hooks) XX Pull Rope (20, 25, 30, 35, 40, 50') 1 23 Determined 4 by Length Pullrod (85, 91, 93, 96, 100, 105" Lengths) Pullrod Hardware Kit

Steel Protector, 7 Aluminum Windguard, 9 Open & Steel Protector Plus w/electric Drive Conversion Kit Installation Instructions

Steel Protector, 7 Aluminum Windguard, 9 Open & Steel Protector Plus w/electric Drive Conversion Kit Installation Instructions WLH 0/0/ 0-0, 0-09, 0-0, 0-0 (0-0 Configuration) 0-0 TABLE OF CONTENTS ***Assembly*** ***Wiring, Parts & Tools Required*** Securing Roller and Removing Tarp... Electric Motor Wiring and Plug Assembly...

More information

Smart Switch with External Switch - 12 volt - ( )

Smart Switch with External Switch - 12 volt - ( ) Smart Switch with External Switch - 12 volt - (501-9953) Wiring Instructions MOTOR (-) / 6 ga. wire MOTOR (+) / 6 ga. wire CONTROL BOX BAT (-) / 6 ga. wire BAT (+) / 6 ga. wire MOTOR BAB 1/23/09 KJH 04/23/08

More information

Smart Switch Basic Kit - 24 volt ( ) Wiring Instructions

Smart Switch Basic Kit - 24 volt ( ) Wiring Instructions Smart Switch Basic Kit - 4 volt (54-08) Wiring Instructions NB 8/0/ 6 ga. wire 6 ga. wire 6 ga. wire OUT IN 6 ga. wire Yellow Black Blue 50 AMP BREAKER MOTOR 6 ga. wire 6 ga. wire 6 ga. wire ROCKER SWITCH

More information

Patriot. Aluminum and Steel 5spring. Step #1 Tarp Spool with Gear Motor (Includes Instructions for Optional Wind Deflector)

Patriot. Aluminum and Steel 5spring. Step #1 Tarp Spool with Gear Motor (Includes Instructions for Optional Wind Deflector) Aluminum and Steel 5spring Qty. Component Parts Description: LONG BOX: (1) 103 Aluminum Tarp Axle (2) 98 Upper Arms with 90 Degree Elbow (2) Lower Aluminum ( 84 ) (1) Aluminum Cross Tube SMALL HARDWARE

More information

Superwinch 12 Volt Smart Switch w/ Wireless Remote Kit Installation Instructions

Superwinch 12 Volt Smart Switch w/ Wireless Remote Kit Installation Instructions 1404 N. Marshall Ave. El Cajon CA. 92020 WLH 08/09/18 514-0141 607-0143 TABLE OF CONTENTS ***Assembly*** ***Parts & Tools*** Wiring the Motor... 1 Smart Switch Basic Kit - Wiring Diagram #514-0141... 5

More information

MIC210 Electric Farm Conversion Instructions

MIC210 Electric Farm Conversion Instructions MIC210 Electric Farm Conversion Instructions Note: Apply the supplied Dielectric Lubricant to all wire connections when each wire is hooked up. The Dielectric Lubricant will help to prevent corrosion.

More information

INSTALLATION, MAINTENANCE, & SAFETY INSTRUCTIONS

INSTALLATION, MAINTENANCE, & SAFETY INSTRUCTIONS Tarpaulin Systems Flip -N- Go / Quick Mount Flip -N- Go System INSTALLATION, MAINTENANCE, & SAFETY INSTRUCTIONS (800) CRAMARO (800) 272-6276 Plants In: Delaware, Florida, Massachusetts, Nevada, Ohio Install

More information

FARM MODEL INSTALLATION INSTRUCTIONS

FARM MODEL INSTALLATION INSTRUCTIONS REAR ATTACHMENT ELECTRIC CONVERSION FARM MODEL INSTALLATION INSTRUCTIONS This page intentionally left blank MICHEL S INDUSTRIES, LTD. p.o. Box 119 St. GREGOR,SK PH: 306.366.2184 em: SALES@MICHELS.CA 1

More information

Side Dump Tarp System Driver or Passenger Stowing Non-Sealed applications

Side Dump Tarp System Driver or Passenger Stowing Non-Sealed applications Roll Rite, LLC and its entire staff would like to not only Thank You but congratulate you on your purchase of one of what we feel to be the finest line of tarping systems in the industry. Side Dump Tarp

More information

A B C D E F. Tools Required (supplied by others)

A B C D E F. Tools Required (supplied by others) Page 1 of 17 Parts List Below Deck Automatic Retractable Security Cover Kit (1) Tube End Bearing Plate (A) (1) Rope Reel and Cover Drum Motor Assembly (B) (1) Cover Drum (1) Pulley Support Channel (2)

More information

INSTRUCTIONS, (FORD) SUPER DUTY INSTALLATION KIT (C2 PICKUP LIFTGATES)

INSTRUCTIONS, (FORD) SUPER DUTY INSTALLATION KIT (C2 PICKUP LIFTGATES) LIFT CORPORATION Sht. 1 of 22 DSG# M-16-32 Rev. - Date: 12/13/16 INSTRUCTIONS, (FORD) SUPER DUTY INSTALLATION KIT (C2 PICKUP LIFTGATES) FORD SUPER DUTY F-250, F-350 & F-450 PICKUP TRUCKS, 2017 MODEL KIT

More information

Deluxe High Amp Switch Kit - 12 Volt Wiring Instructions

Deluxe High Amp Switch Kit - 12 Volt Wiring Instructions 1404 N. Marshall Ave. El Cajon C 92020 WLH 09/01/16 514-0139 OUT IN 16 ga. Black wire 16 ga. Green wire Yellow Black Blue 50 AMP BREAKER MOTOR 16 ga. White wire ROCKER SWITCH (IN CAB) BATTERY 607-0139

More information

GRAIN CART TARP SYSTEM INSTALLATION AND OPERATION MANUAL

GRAIN CART TARP SYSTEM INSTALLATION AND OPERATION MANUAL GRAIN CART TARP SYSTEM INSTALLATION AND OPERATION MANUAL Grain Carts KITS Thunderstone Manufacturing, LLC. 3400 West O Street Lincoln, NE 68528 402-435-4249 (Fax) 402-438-3918 www.thunderstonemfg.com Aluminum

More information

Installation Instructions Models 2858, 2858A-1, 2858GL February 2009

Installation Instructions Models 2858, 2858A-1, 2858GL February 2009 Installation Instructions Models 2858, 2858A-1, 2858GL February 2009 www.donovan-ent.com Donovan Enterprises 3353 SE Gran Park Way Stuart, FL 34997 800-327-8287 Step 1 Head Assembly Installation Instructions

More information

INSTRUCTIONS, NISSAN TITAN TRUCK INSTALLATION KIT (C2 PICKUP LIFTGATES)

INSTRUCTIONS, NISSAN TITAN TRUCK INSTALLATION KIT (C2 PICKUP LIFTGATES) LIFT CORPORATION Sht. 1 of 18 DSG# M-14-33 Rev. A Date: 05/31/2017 INSTRUCTIONS, NISSAN TITAN TRUCK INSTALLATION KIT (C2 PICKUP LIFTGATES) NISSAN TITAN PICKUP TRUCKS, 2004-2015 KIT P/N 295040-01 MOUNTING

More information

Installation Instructions. Attention Dealers: Please give this owners manual to the customer when the product is delivered.

Installation Instructions. Attention Dealers: Please give this owners manual to the customer when the product is delivered. Serving the Truck & Trailer Industry Since 1944 Attention Dealers: Please give this owners manual to the customer when the product is delivered. Call 800-535-9545 www.aeroindustries.com Indianapolis, IN

More information

Installation Instructions February 2009

Installation Instructions February 2009 Installation Instructions February 2009 www.donovan-ent.com Donovan Enterprises 3353 SE Gran Park Way Stuart, FL 34997 800-327-8287 The Hammer Head Assembly Installation Instructions (Rollerbar & Direct

More information

SUT-250-S (These instructions are used for SUT-250-SCLC also)

SUT-250-S (These instructions are used for SUT-250-SCLC also) SUT-250-S (These instructions are used for SUT-250-SCLC also) Torque wrench, carpenters square, wire cutters, Phillips screwdriver, 7/16, 9/16, and 3/4 combination wrenches, ratchet, 9/16, 3/4, 13/16,

More information

Midwest Industries, Inc. Ida Grove, IA Page 1

Midwest Industries, Inc. Ida Grove, IA Page 1 SSV40108HAC - Hydraulic Hoist with 120 Volt Pump SSV40108HDAC - Hydraulic Hoist, Deep Water, with 120 Volt Pump SSV40108HDC - Hydraulic Hoist with 12 Volt Pump SSV40108HDDC - Hydraulic Hoist, Deep Water,

More information

INSTRUCTIONS, (FORD) SUPER DUTY INSTALLATION KIT (C2 PICKUP LIFTGATES)

INSTRUCTIONS, (FORD) SUPER DUTY INSTALLATION KIT (C2 PICKUP LIFTGATES) LIFT CORPORATION Sht. 1 of 20 DSG# M-14-32 Rev. B Date: 05/31/2017 INSTRUCTIONS, (FORD) SUPER DUTY INSTALLATION KIT (C2 PICKUP LIFTGATES) FORD SUPER DUTY F-250 PICKUP TRUCKS, 1999-2016 FORD SUPER DUTY

More information

Installation Instructions

Installation Instructions DODGE 24K Industry Standard Rail Heavy Duty Custom Mounting Kit #2230 Gross Trailer Weight (Maximum)...24,000 lbs. Vertical Load Weight (Max. Pin Weight)...6,000 lbs. SYSTEM TOW CAPACITY Please note, in

More information

INSTALLATION and MAINTENANCE INSTRUCTIONS SHO SERIES ELECTRIC CABLE REELS

INSTALLATION and MAINTENANCE INSTRUCTIONS SHO SERIES ELECTRIC CABLE REELS INSTALLATION and MAINTENANCE INSTRUCTIONS SHO SERIES ELECTRIC CABLE REELS All units are provided with right hand rotation unless otherwise specified. This means that cable is pulled off spool top left

More information

ONE TOUCH CONTROL BOX

ONE TOUCH CONTROL BOX ONE TOUCH CONTROL BOX CONVERSION KIT INSTRUCTIONS REMOVAL, INSTALLATION, OPERATION, AND REMOTE CONTROL PROGRAMMING THUNDERSTONE PART #101322 REVISION A JULY 14 TH 2016 2 P a g e INSTALLING THE THUNDER

More information

Installation Guide. Installation Guide. Exploded Views Installation Instructions Mounting System Parts List. USTarp.

Installation Guide. Installation Guide. Exploded Views Installation Instructions Mounting System Parts List. USTarp. Installation Guide Installation Guide Exploded Views Installation Instructions Mounting System Parts List USTarp.com 800-249-0297 Fits dump trailers up to 40 long, or up to 45 long with Bulletproof HD

More information

INSTALLATION INSTRUCTIONS C-VS-2000-DUR-1 20 VEHICLE SPECIFIC CONSOLE for 2018 Dodge Durango with Standard Shifter

INSTALLATION INSTRUCTIONS C-VS-2000-DUR-1 20 VEHICLE SPECIFIC CONSOLE for 2018 Dodge Durango with Standard Shifter INSTALLATION INSTRUCTIONS C-VS-2000-DUR-1 20 VEHICLE SPECIFIC CONSOLE for 2018 Dodge Durango with Standard Shifter TOOLS REQUIRED: Phillips Screw Driver T-20 Torx bit Standard Socket set 9/64 Allen wrench

More information

Installation Instructions Table of Contents

Installation Instructions Table of Contents Installation Instructions Table of Contents Pre- Installation of Garage Storage Lift 2 Layout the Garage Storage Lift 3 Installing the strut Channels 3 Install the Drive Assembly 5 Install the Drive Shaft

More information

Pulltarps Tower with Electric Drive

Pulltarps Tower with Electric Drive Pulltarps Tower with Electric Drive 513-0011 / 513-0012 1404 N. Marshall Ave. El Cajon CA. 92020 For technical support call us at (800) 368-3075 www.pulltarps.com 607-0116 RH 08/26/13 Pulltarps Tower Installation

More information

Easy Cover. Installation Instructions. Attention Dealers: Please give this owners manual to the customer when the product is delivered.

Easy Cover. Installation Instructions. Attention Dealers: Please give this owners manual to the customer when the product is delivered. Serving the Truck & Trailer Industry Since 944 Easy Cover Attention Dealers: Please give this owners manual to the customer when the product is delivered. Call 00-3-94 www.aeroindustries.com Indianapolis,

More information

and Original Series Pickup Lift Mounting Instructions Fleetside Chevy & GMC Trucks Fleetside 4-door Chevy & GMC Trucks T-100

and Original Series Pickup Lift Mounting Instructions Fleetside Chevy & GMC Trucks Fleetside 4-door Chevy & GMC Trucks T-100 r ve and Original Series Pickup Lift Mounting Instructions Fleetside Chevy & GMC Trucks - 1960-1987 Fleetside 4-door Chevy & GMC Trucks - 1988-1991 Preparing the Gate 1. Remove the mounting hardware which

More information

MF 9690, 9790, Challenger 660, 670

MF 9690, 9790, Challenger 660, 670 Ag Leader Technology Parts List Note: Indented items indicate parts included in an assembly listed above Quantity by Model Part Name/Description Part No. MF 9690 MF 9790 Challenger 660 Challenger 670 Instruction

More information

A B C D E F. b.tools Required (supplied by others) 3/16" Drill Bit 3/8" Wrench Phillips Head Screwdriver

A B C D E F. b.tools Required (supplied by others) 3/16 Drill Bit 3/8 Wrench Phillips Head Screwdriver Page 1 of 13 5E.1 Parts List a. Below Deck Automatic Retractable Security Cover Kit (1) Tube End Bearing Plate (A) (1) Rope Reel with Motor Attached (B) (1) Rope Reel Cover (C) (1) Cover Drum (1) Cover

More information

Installation Instructions

Installation Instructions DODGE 20K Industry Standard Rail Custom Mounting Kit #2740 Gross Trailer Weight (Maximum)...20,000 lbs. Vertical Load Weight (Max. Pin Weight)...5,000 lbs. SYSTEM TOW CAPACITY Please note, in order to

More information

PFadvantage Metalfor Araus 1360

PFadvantage Metalfor Araus 1360 Metalfor Araus 1360 Note: Indented items indicate parts included in an assembly listed above Part Name/Description Part Number Quantity Instruction Kit Metalfor Araus 2005300-14 1 Display Bracket 4000134

More information

and Original Series Pickup Lift Mounting Instructions Fullsize Nissan Titan Trucks present T-420 BOLT-ON GUSSET PART#5257

and Original Series Pickup Lift Mounting Instructions Fullsize Nissan Titan Trucks present T-420 BOLT-ON GUSSET PART#5257 and Original Series Pickup Lift Mounting Instructions Fullsize Nissan Titan Trucks- 2004-present Preparing the Gate 1. Remove the mounting hardware which is banded to the liftgate. 2. Verify mounting bracket

More information

Installation Instructions Supertop for Truck

Installation Instructions Supertop for Truck Installation Instructions Supertop for Truck US Patent 6827391 Vehicle Application: Toyota Tacoma Double Cab 2005-2011 (5 ft.) Part Number: 76308 INSTALLATION TIME SKILL LEVEL 1-1/2 Hours 2 - Moderately

More information

Z-Gate Universal Shifter

Z-Gate Universal Shifter Installation Instructions Z-Gate Universal Shifter Fits: GM, Ford, Lincoln and Chrysler Transmissions See Application Guide for Specific Applications Part #80681 Rev 06/01/2018 WORK SAFELY! For maximum

More information

Side Kick 2. Installation Instructions & Parts Lists. Attention Dealers: Please give this owners manual to the customer when the product is delivered.

Side Kick 2. Installation Instructions & Parts Lists. Attention Dealers: Please give this owners manual to the customer when the product is delivered. Serving the Truck & Trailer Industry Since 1944 Side Kick 2 Installation Instructions & Parts Lists Attention Dealers: Please give this owners manual to the customer when the product is delivered. Call

More information

INSTALLATION INSTRUCTIONS 89551

INSTALLATION INSTRUCTIONS 89551 INSTALLATION INSTRUCTIONS 89551 For Rancho Suspension System RS66551B: Ford F250, F350 Super Duty 4x4 DIESEL ONLY (Single Rear Wheels Only With or Without Auxiliary Spring). (WILL NOT WORK ON GAS ENGINES

More information

Ag Leader Technology. Parts List for Combine MF , 8780, White 9700

Ag Leader Technology. Parts List for Combine MF , 8780, White 9700 Parts List for Combine Quantity by Model Note: Indented items indicate parts included W in an assembly listed above 8 8 8 8 H 5 5 5 7 I 6 7 9 8 T Part Name/Description Part No. 0 0 0 0 E Instruction Kit

More information

Installation Manual TWM Performance Short Shifter Cobalt SS/SC, SS/TC, HHR SS, Ion Redline and Saab 9-3

Installation Manual TWM Performance Short Shifter Cobalt SS/SC, SS/TC, HHR SS, Ion Redline and Saab 9-3 Page 1 Installation Manual TWM Performance Short Shifter Cobalt SS/SC, SS/TC, HHR SS, Ion Redline and Saab 9-3 Please Note: It is preferable to park on a flat surface, as you will have to engage and disengage

More information

SUT-450-I ASSEMBLY REQUIREMENTS

SUT-450-I ASSEMBLY REQUIREMENTS SUT-450-I Torque wrench, carpenters square, wire cutters, Phillips screwdriver, 7/16, 9/16, and 3/4 combination wrenches, ratchet, 9/16,3/4,13/16, and 7/8 sockets. ASSEMBLY REQUIREMENTS *Torque all T-bolt

More information

2000SR. Installation Instructions May Donovan Enterprises 3353 S.E. Gran Park Way Stuart, Florida

2000SR. Installation Instructions May Donovan Enterprises 3353 S.E. Gran Park Way Stuart, Florida 311499-Donovan 4/28/04 11:22 PM Page 1 Installation Instructions May 2003 Donovan Enterprises 3353 S.E. Gran Park Way Stuart, Florida 34997 1-800-327-8287 Visit our web site at: www.donovan-ent.com 311499-Donovan

More information

Installation Guide Current Ford F-250 & Ford F-350 Super Duty. Product Code: 109 & 119

Installation Guide Current Ford F-250 & Ford F-350 Super Duty. Product Code: 109 & 119 Installation Guide 2008 - Current Ford F-250 & Ford F-350 Super Duty Product Code: 109 & 119 September 1, 2012 Tools Needed Components Included 3/8" Drill P2 Tip #2 Philips Screwdriver 1/2" Drill Bit Hinged

More information

table of Contents Warranty:

table of Contents Warranty: table of Contents placement of the Mounting Bolts spudnik swingout... 2 spudnik solid... 2 logan swingout... 3 logan solid... 3 double l swingout... 4 double l solid... 4 Mounting Framework... 5-6 Mounting

More information

Flow Sensor Deflector Deflector

Flow Sensor Deflector Deflector Parts List of Combine Kit Note: Indented items indicate parts included Quantity by Model in an assembly listed above Early Models* 9 9 9 4 5 6 0 0 0 Part Name/Description Part No. 0 0 0 Instruction Kit

More information

INSTALLATION INSTRUCTIONS RATTLER STEEL RUNNING BOARDS FORD TRANSIT VAN (FULL SIZE)

INSTALLATION INSTRUCTIONS RATTLER STEEL RUNNING BOARDS FORD TRANSIT VAN (FULL SIZE) INSTALLATION INSTRUCTIONS PARTS LIST: 1 32-inch Steel Running Board 1 8-1.25mm x 35mm Hex Bolt 1 96-inch Steel Running Board 13 8-1.25mm x 25mm Hex Bolt 5 Passenger Side/Driver Side Mounting Brackets 20

More information

Installation Instructions Supertop for Truck

Installation Instructions Supertop for Truck Installation Instructions Supertop for Truck US Patent 6827391 Vehicle Application: Ford F150 1987-1996 (8 ft.) Part Number: 76315 Ford F250 1987-1998 (8 ft.) Part Number: 76315 Ford F350 1987-1998 (8

More information

Installation Instructions PowerBoard Automatic Retracting Running Board

Installation Instructions PowerBoard Automatic Retracting Running Board Installation Instructions PowerBoard Automatic Retracting Running Board Vehicle Application Chevy Silverado/GMC Sierra Extended Cab Diesel 2011 and newer Part Number: 75147-15 Chevy Silverado/GMC Sierra

More information

Combine Cover Manual

Combine Cover Manual Combine Cover Manual Installation Instructions Page 27 Operating Instructions Page 8 Warranty Page 8 Trouble Shooting Page 9 11 For Model s: Case I.H. 2388, 2188, 1688 and 1680 With a MAURER Hopper Extension

More information

1-3/8 Designer Metals Telescoping Traversing Rod Installation Instructions

1-3/8 Designer Metals Telescoping Traversing Rod Installation Instructions 1-3/8 Designer Metals Telescoping Traversing Rod Installation Instructions Please read and follow all installation instructions provided for proper operation and enjoyment of your new drapery hardware

More information

920 Remote Control Switches

920 Remote Control Switches 920 Remote Control Switches REMOTE CONTROL SWITCHES Service Bulletin This service bulletin for ASCO 920 Remote Control Switches explains how to replace the main s, operator coil, control s, and how to

More information

Installation Instructions

Installation Instructions FORD 20K Industry Standard Rail Custom Mounting Kit #2738 Gross Trailer Weight (Maximum)...20,000 lbs. Vertical Load Weight (Max. Pin Weight)...5,000 lbs. SYSTEM TOW CAPACITY Please note, in order to determine

More information

Additional Instructions for 6" Drop

Additional Instructions for 6 Drop Serving the Truck & Trailer Industry Since 1944 Additional Instructions for 6" Drop Attention Dealers: Please give this manual to the customer when product is delivered. Call 800-535-9545 www.aeroindustries.com

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Thank you for purchasing an AUTOLOCK Electric Tarp. ACI proudly manufactured this product using superior quality materials and workmanship. With proper care, your tarp will provide

More information

INSTALLATION MANUAL. Thunderstone Manufacturing LLC 3400 West O Street Lincoln, NE (Fax)

INSTALLATION MANUAL. Thunderstone Manufacturing LLC 3400 West O Street Lincoln, NE (Fax) INSTALLATION MANUAL August 7 th 2018 43 /48 /50 2011 and Older Timpte STD/Split 36 Style Hopper Trailers with Roller Bearing Doors Kit #101533 for 96w & Kit #101534 for 102w Thunderstone Manufacturing

More information

Installation Instructions

Installation Instructions DODGE 20K Industry Standard Rail Custom Mounting Kit #2742 Gross Trailer Weight (Maximum)...20,000 lbs. Vertical Load Weight (Max. Pin Weight)...5,000 lbs. SYSTEM TOW CAPACITY Please note, in order to

More information

Part Name/Description Part Number Quantity Instruction Kit Metalfor Flow Sensor

Part Name/Description Part Number Quantity Instruction Kit Metalfor Flow Sensor NOTE: Indented items indicate parts included in an assembly listed above Part Name/Description Part Number Quantity Instruction Kit Metalfor 4101091 1 Flow Sensor 4001356 1 Deflector plate 2000612-1 1

More information

Pontoon Assembly Instructions and manual. Read before using hoist.

Pontoon Assembly Instructions and manual. Read before using hoist. Page 1 Pontoon Assembly Instructions and manual. Read before using hoist. For Models 32BL18, 32BL22, 32BL25 and 42BL28 R Model 32BL22 Shown Proudly Made in Michigan By NuCraft Metal Products 402 Southline

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Accessory HITCH Application 2009 CR-V Publications No. AII 40373 Issue Date AUG 2008 PARTS LIST Plain washer, 12 mm Trailer Hitch Kit P/N 08L92-SWA-100 Trailer hitch 6 Spring

More information

PRO RATCHET UNIVERSAL SHIFTER

PRO RATCHET UNIVERSAL SHIFTER Installation Instructions PRO RATCHET UNIVERSAL SHIFTER Fits: GM, Ford and Chryslers w/automatic Transmission See Application Guide for Specific Vehicles Catalog # 80842 WORK SAFELY! For maximum safety,

More information

Installation Instructions for John Deere cotton picker models: 9986 & 2-row and All-row systems included.

Installation Instructions for John Deere cotton picker models: 9986 & 2-row and All-row systems included. Ag Leader Technology Cotton Picker Installation Installation Instructions for John Deere cotton picker models: 9986 & 9996 2-row and All-row systems included. IMPORTANT: Ensure the model numbers shown

More information

INSTALLATION & OWNER S MANUAL

INSTALLATION & OWNER S MANUAL Rev. A, p. 1 of 13 INSTALLATION & OWNER S MANUAL Polaris Ranger (2009-) Straight UTV Steel Plow with Vehicle Mount Kit 6 Wide Snow Plow (p/n: 1POLSP) (fits the 500 H.O., 700 & 800 HD & XP) The contents

More information

SRT-2 MANUAL AND ELECTRIC

SRT-2 MANUAL AND ELECTRIC Installation Manual SRT-2 MANUAL AND ELECTRIC BY: INSTALLER: These instructions must be given to the consumer. CONSUMER: Retain these instructions for further use. Save this manual for future reference.

More information

TOYOTA SIENNA TRAILER WIRE HARNESS Preparation

TOYOTA SIENNA TRAILER WIRE HARNESS Preparation Preparation Part Number: PT791-08150 (non-se) PT791-08102 (SE only) Kit Contents Item # Quantity Reqd. Description 1 1 Trailer Module Harness 2 1 4-Flat Harness 3 1 Battery Power Wire Harness 4 1 Mounting

More information

MENTOR INSTALLATION, MAINTENANCE, & SAFETY INSTRUCTIONS (800)

MENTOR INSTALLATION, MAINTENANCE, & SAFETY INSTRUCTIONS (800) MENTOR INSTALLATION, MAINTENANCE, & SAFETY INSTRUCTIONS (800) 272-6276 001-321-757-7611 www.cramarotarps.com Plants In: Delaware, Florida, Massachusetts, Nevada, Ohio, and Canada Important: Read before

More information

Instructions for 2-row monitoring only

Instructions for 2-row monitoring only Installation Instructions for CaseIH cotton picker models: Instructions for 2-row monitoring only CAUTION: Ensure the model numbers shown above correspond to the machine model. If you receive the incorrect

More information

INSTALLATION INSTRUCTION 88146

INSTALLATION INSTRUCTION 88146 INSTALLATION INSTRUCTION 88146 Rev H FOR RANCHO SUSPENSION SYSTEM RS6547: 4WD SUBURBAN/YUKON XL, 4WD TAHOE/YUKON, & 4WD AVALANCHE READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH BEFORE BEGINNING

More information

Installation Instructions PowerBoard Automatic Retracting Running Board

Installation Instructions PowerBoard Automatic Retracting Running Board Installation Instructions PowerBoard Automatic Retracting Running Board Vehicle Application Ford Super Duty F-250/350/450 Crew Cab 2008 and newer Part Number: 75134-15 www.bestop.com - We re here to help!

More information

Photo 1. Shift pattern gate plate

Photo 1. Shift pattern gate plate Installation Instructions MAGNUM GRIP STREET BANDIT SHIFTER Fits: GM, Chrysler, and Ford Automatic Transmissions See Application Guide for Specific Vehicles Catalog # 81050 WORK SAFELY! For maximum safety,

More information

Installation Instructions PowerBoard Automatic Retracting Running Board

Installation Instructions PowerBoard Automatic Retracting Running Board Installation Instructions PowerBoard Automatic Retracting Running Board Vehicle Application Chevy Silverado/GMC Sierra Extended Cab 2007 and newer (excluding 2011 Diesels) Part Number: 75123-15 Chevy Silverado/GMC

More information

Installation Instructions

Installation Instructions FORD 20K Industry Standard Rail Custom Mounting Kit #2766 Gross Trailer Weight (Maximum)...20,000 lbs. Vertical Load Weight (Max. Pin Weight)...5,000 lbs. SYSTEM TOW CAPACITY Please note, in order to determine

More information

650 Series Cargo Van Lift Mounting Instructions Ford Transit (Standard Roof) 2015-Present

650 Series Cargo Van Lift Mounting Instructions Ford Transit (Standard Roof) 2015-Present TOMMY GATE OWNER'S / OPERATOR'S MANUAL 650 Series 650 LB Capacity 650 Series Cargo Van Lift Mounting Instructions Ford Transit (Standard Roof) 2015-Present Installing the Base Plate 1. Examine the interior

More information

SPO15, SPO18 I N S T A L L A T I O N I N S T R U C T I O N S

SPO15, SPO18 I N S T A L L A T I O N I N S T R U C T I O N S SPO15, SPO18 Sprinter SPO15 (3A0 Lifts) Capacity 11,000 lbs. Standard SPO15 (300 Series Lifts) Capacity 15,000 lbs. Standard SPO18 (300 Series Lifts) Capacity 18,000 lbs. SPO15 (31A0 Lifts) Capacity 14,300

More information

N. 15th Street, Middlesboro, KY TARP-N-GO SYSTEMS INSTALLATION INSTRUCTIONS

N. 15th Street, Middlesboro, KY TARP-N-GO SYSTEMS INSTALLATION INSTRUCTIONS 1-800-248-7717 1002 N. 15th Street, Middlesboro, KY 40965 TARP-N-GO SYSTEMS INSTALLATION INSTRUCTIONS Congratulations on your purchase of a Mountain Tarp Tarp-N-Go tarping system. With tarping systems

More information

Instructions for 2-row monitoring only

Instructions for 2-row monitoring only Installation Instructions for CaseIH cotton picker models: Instructions for 2-row monitoring only Ensure the model numbers shown above correspond to the machine model. If you receive the incorrect installation

More information

and Original Series Pickup Lift Mounting Instructions Fullsize Chevy & GMC Trucks: 1500 & 2500 LD HD & 3500HD BOLT-ON GUSSET

and Original Series Pickup Lift Mounting Instructions Fullsize Chevy & GMC Trucks: 1500 & 2500 LD HD & 3500HD BOLT-ON GUSSET r ve and Original Series Pickup Lift Mounting Instructions Fullsize Chevy & GMC Trucks: 1500 & 2500 LD 1999-2007 2500HD & 3500HD 2000-2007 Preparing the Gate 1. Remove the mounting hardware which is banded

More information

TCI FastGate Shifter Installation Instructions

TCI FastGate Shifter Installation Instructions 151 INDUSTRIAL DRIVE ASHLAND, MISSISSIPPI 38603 http://www.tciauto.com TELEPHONE: 662-224-8972 FAX LINE: 662-224-8255 E-MAIL: tech@tciauto.com TCI 616541 FastGate Shifter Installation Instructions The

More information

GPS AutoSteer System Installation Manual

GPS AutoSteer System Installation Manual GPS AutoSteer System Installation Manual Supported Vehicles Case IH Vehicles Case 2577 Combines Case 2588 Combines Accuguide Ready PN: 602-0233-01-A LEGAL DISCLAIMER Note: Read and follow ALL instructions

More information

INSTALLATION INSTRUCTIONS 88511

INSTALLATION INSTRUCTIONS 88511 INSTALLATION INSTRUCTIONS 88511 For Suspension System RS6511: Ford Super Duty Requires coil spring kit RS80117 or RS80119 for a complete installation READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH

More information

LIFT N LOAD INSTALLATION, MAINTENANCE, & SAFETY INSTRUCTIONS (800)

LIFT N LOAD INSTALLATION, MAINTENANCE, & SAFETY INSTRUCTIONS (800) LIFT N LOAD INSTALLATION, MAINTENANCE, & SAFETY INSTRUCTIONS (800) 272-6276 001-321-757-7611 www.cramarotarps.com Plants In: Delaware, Florida, Massachusetts, Nevada, Ohio, and Canada General Information

More information

PLEASE READ THIS INSTRUCTIONS CAREFULLY, BEFORE YOU START INSTALLATION

PLEASE READ THIS INSTRUCTIONS CAREFULLY, BEFORE YOU START INSTALLATION INSTALLATION INSTRUCTIONS PART NUMBER: L0SXC000 DESCRIPTION: 09 ASCENT TRAILER HITCH PLEASE READ THIS INSTRUCTIONS CAREFULLY, BEFORE YOU START INSTALLATION SAFETY PRECAUTION: When installing Trailer Hitch,

More information

! DANGER Lb. Winch Mounting Instructions. Tools required: Before You Start. Assembly Instructions. General Information. Manual No.

! DANGER Lb. Winch Mounting Instructions. Tools required: Before You Start. Assembly Instructions. General Information. Manual No. 500 Lb. Winch Mounting Instructions For 400/4400 NT/ST, 40/440 ST And 40/440 ST Manual No. 70-86M Before You Start! When you see this symbol, the subsequent instructions and warnings are serious - follow

More information

Assembly Instructions

Assembly Instructions Assembly Instructions Part Number Description Model Approx. Assembly Time 99994-0903 Windshield Wiper Kit Mule SX 1 Hour WARNING Improper installation of this accessory could result in an accident causing

More information

INSTALLATION INSTRUCTIONS 97 FORD EXPEDITION

INSTALLATION INSTRUCTIONS 97 FORD EXPEDITION INSTALLATION INSTRUCTIONS 97 FORD EXPEDITION 1. Read the instructions completely and carefully before you begin. Check the kit for proper contents (refer to the part s list and the picture diagrams). Before

More information

Installation Instructions Supertop NX Twill

Installation Instructions Supertop NX Twill Installation Instructions Supertop NX Twill Vehicle Application: Jeep Wrangler Unlimited 2007-current Part Number 54823 Installation Tips Before you begin installing your new Supertop NX Twill, please

More information

BELLY DUMP MANUAL AND ELECTRIC INSTALLATION INSTRUCTIONS AND OWNER S MANUAL

BELLY DUMP MANUAL AND ELECTRIC INSTALLATION INSTRUCTIONS AND OWNER S MANUAL BELLY DUMP MANUAL AND ELECTRIC INSTALLATION INSTRUCTIONS AND OWNER S MANUAL BY: INSTALLER: These instructions must be given to the consumer. CONSUMER: Retain these instructions for further use. Save this

More information

TOYOTA VENZA 2009 TRAILER WIRE HARNESS Procedure

TOYOTA VENZA 2009 TRAILER WIRE HARNESS Procedure Part Number: PT791-0T099 Kit Contents Item # Quantity Reqd. Description 1 1 Trailer Wire Harness Module 2 1 4-Flat Harness 3 1 Battery Power Wire Harness 4 1 Mounting Bracket, 4-Flat 5 2 Screw #10-24 6

More information

Deuce/Ace Installation Instructions

Deuce/Ace Installation Instructions HARDWARE KIT: Upper Mounting Plate: 2-7/16" (11mm) X 3.5" bolts 2-7/16" flange nuts 2-2" spacers 2-7/16" trim cap mounting washers 2 - plastic trim caps TOOLS NEEDED: safety glasses wrenches 16mm or 5/8"

More information

INSTALLATION GUIDE. AMP RESEARCH TECH SUPPORT (Press 2) Monday - Friday, 6:00 AM - 5:00 PM PST

INSTALLATION GUIDE. AMP RESEARCH TECH SUPPORT (Press 2) Monday - Friday, 6:00 AM - 5:00 PM PST INSTALLATION GUIDE APPLICATION AMP Part # Chevrolet Silverado / GMC Sierra - Ext. Cab 2007 - up 75123-01A Chevrolet Silverado / GMC Sierra - Crew Cab 2007 - up 75126-01A Chevrolet Silverado / GMC Sierra

More information

Model E600 Tarping System

Model E600 Tarping System 10 Boulder Parkway N. Oxford, MA 01537 866-353-5826 pioneersales@wastequip.com www.pioneercoverall.com Model E600 Tarping System Installation Instructions WARNING: In order to prevent damage, the tarp

More information

650 Series Cargo Van Lift Mounting Instructions Fullsize Ford 1992-Present

650 Series Cargo Van Lift Mounting Instructions Fullsize Ford 1992-Present TOMMY GATE OWNER'S / OPERATOR'S MANUAL 650 Series 650 LB Capacity 650 Series Cargo Van Lift Mounting Instructions Fullsize Ford 1992-Present Installing the Base Plate 1. Examine the interior and exterior

More information

Installation Instructions PowerBoard Automatic Retracting Running Board

Installation Instructions PowerBoard Automatic Retracting Running Board Installation Instructions PowerBoard Automatic Retracting Running Board Vehicle Application Chevy Silverado/GMC Sierra Extended Cab 2007 and newer (excluding 2011 Diesels) Part Number: 75123-15 Chevy Silverado/GMC

More information

INSTALLATION INSTRUCTIONS 88518

INSTALLATION INSTRUCTIONS 88518 INSTALLATION INSTRUCTIONS 88518 For Rancho Suspension Systems RS6518: 2009 FORD F-150 4WD READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH BEFORE BEGINNING INSTALLATION Rev A IMPORTANT NOTES! WARNING:

More information

Suspension System RS6525 (B)

Suspension System RS6525 (B) 88525 Rev A Suspension System RS6525 (B) Requires coil spring kit RS80116 (B) or RS80118 (B) for a complete installation Ford Super Duty READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH BEFORE BEGINNING

More information

Installation Instructions Z-Gate Shifter

Installation Instructions Z-Gate Shifter Installation Instructions Z-Gate Shifter Part Number 80681 1998, 2001 by B&M Racing and Performance Products The B&M Z-Gate shifter can be used in vehicles equipped with most popular three speed automatic

More information

L DODGE CUMMINS BD FLOWMAX LIFT PUMP KIT

L DODGE CUMMINS BD FLOWMAX LIFT PUMP KIT 6/15/2016 #1050311D 2010-12 6.7 Dodge Cummins FlowMAX Lift Pump Kit (I-00329) - 1-2010-12 6.7L DODGE CUMMINS BD FLOWMAX LIFT PUMP KIT Installation Instructions P/N # 1050311D PLEASE READ ALL INSTRUCTIONS

More information

FlexJet - Flex Cable Replacement

FlexJet - Flex Cable Replacement P/N: 109515R0 14140 NE 200th St. Woodinville, WA. 98072 PH: (425) 398-8282 FX: (425) 398-8383 FlexJet - Flex Cable Replacement Notices: Warning! Ensure that all AC power cables are removed from the printer

More information

Maintenance Information

Maintenance Information Form 16575334 Edition 1 April 2005 Electric Screwdrivers EL, EP and ET 34V DC Series Maintenance Information Save These Instructions WARNING Maintenance procedures have the potential for severe shock hazard

More information

Installation Instructions COMPETITION/PLUS SHIFTER Ford Mustang MT82 6-Speed Manual Transmission Catalog#

Installation Instructions COMPETITION/PLUS SHIFTER Ford Mustang MT82 6-Speed Manual Transmission Catalog# Installation Instructions COMPETITION/PLUS SHIFTER 2015-2017 Ford Mustang MT82 6-Speed Manual Transmission Catalog# 3916037 Rev. 00 WORK SAFELY! For maximum safety, perform this installation on a clean,

More information

Agri-Fab OWNER'S MANUAL. Model No POINT HITCH TRAILER.

Agri-Fab OWNER'S MANUAL. Model No POINT HITCH TRAILER. Agri-Fab OWNER'S MANUAL Model No. 45-0353 3-POINT HITCH TRAILER CAUTION: Read Rules for Safe Operation and Instructions Carefully Safety Assembly Operation Maintenance Parts the fastest way to purchase

More information