GCX Mounting Assembly Operation/Installation Manual
|
|
- Quentin McBride
- 6 years ago
- Views:
Transcription
1 GCX Mounting Assembly Operation/Installation Manual Dräger Model Fabius GS with Dräger Vamos, CWS 15 "Recall" and GEMS IT DASH 3000/4000 Patient Monitor Option 1 Option 2 Option 3 Vamos or Dash 3000/4000 Left Side Vamos, Dash 3000 /4000 Left Side, CWS 15 Right Side Vamos Left Side Dash 3000/4000 w/o Dashport Top Shelf CWS 15 Right Side The purpose of these instructions is to: 1. Describe attachment of GCX mounting hardware to the Fabius GS anesthesia machine. 2. Describe attachment of the Vamos, DASH 3000/4000 monitor and CWS 15 Recall to the GCX mounting hardware. WARNING: USE OF MOUNTING HARDWARE AND MONITORING COMPONENTS OTHER THAN THOSE DESCRIBED IN THIS DOCUMENT MAY RESULT IN SERIOUS INJURY DUE TO TIPPING OF THE ANESTHESIA MACHINE. FOR OPTION 2, WHEN VAMOS AND DASH 3000/4000 WILL BE MOUNTED TO THE LEFT SIDE, NO DASHPORT IS ALLOWED. Installer: When installation is completed, provide these instructions to the end user for future reference. DU-DR Dash Rev A 2/13/02 GCX Corp. Page 1 of 13
2 INSTALLATION Install Pivot Arms (Two Options) 1. Upper Position Fabius GS Pivot Arm 1. Guide Fabius GS Pivot Arm Extension Plate Slide into Channel as shown and tighten thumb screw at desired location. Channel Pivot Arm Extension Plate Thumb Screw 2. Guide Hinged Arm and bushing into Extension Plate as shown. Note: Tighten Tension Adjustment Screw for more tension. Bushing Hinged Arm Tension Adjustment Screw PARTS LIST GCX P/N Dräger P/N DESCRIPTION DR DR DR M34080 GCX Adapter Mount w/ 16 Universal Monitor Arm-Kit GCX Adapter Mount only 16 Universal Monitor Arm requires Hinged Arm Oval DU-DR Dash Rev A 2/13/02 GCX Corp. Page 2 of 13
3 2. 16 Pivot Arm Tools required: Hex Key (1/8 ) 1. Guide Pivot Arm slide into channel as shown 2. The Slide has (2) 1 / 4 20 x ¾ SHSS set screws that, when tightened, secure the Arm at the desired location within the Channel. 3. Install the Tilt Limiting Stop Screw and #10 plastic washer. PARTS LIST GCX P/N Dräger P/N DESCRIPTION WMM MM Pivot Arm for Dash or Vamos DU-DR Dash Rev A 2/13/02 GCX Corp. Page 3 of 13
4 INSTRUCTIONS FOR USE M Series Pivot Arm Pivot 1) To pivot the Arm (near the wall), simply push on the side of the Arm or mounted device. 2) To adjust the pivot tension at the Slide, use a ½ (or 13mm) socket driver to tighten or loosen the Pivot Tension Bolt to obtain the desired tension. Pivot Arm Swivel Tension Bolt Pivot Tension Bolt Swivel 1) To rotate the device simply push or pull the corners of the device. 2) To adjust the swivel tension, use a ½ (or 13mm) socket driver to tighten or loosen the Swivel Tension Adjustment Bolt located under the front end of the Arm. Tilt 1) Grasp the top and bottom of the device and tilt it to the desired angle (limited by Tilt Limit Screw) 2) To adjust the overall tilt tension, evenly tighten or loosen the (2) #10-32 x 5/8 SHCS Tilt Tension Adjustment Screws using the supplied 5/32 (4 mm) hex key (may require removal of Tilt Limit Screw Reinstall if removed). Cable Management 1) An open cavity beneath the arm with flexible cable covers manage cables going to and from the front and rear of the arm. Flexible Cable Covers DU-DR Dash Rev A 2/13/02 GCX Corp. Page 4 of 13
5 INSTALLATION Vamos Parts Required: Set Adapter Plate P/N M4 x 6mm Pan Head Slotted screws (4) incl. Tools required : Pan Head Slotted Screwdriver Mount the Adapter Plate to Vamos. Mounting the Vamos to the Pivot Arm 1. Slide Vamos onto Mounting Plate. Pull down the Location Plunger to permit the Adapter Plate to slide all the way onto the Mounting Plate. Slide the monitor until the Location Plunger engages the Adapter Plate, thus securing the monitor in position. 2. Tighten the (4) nylon thumb screws. PARTS LIST GCX P/N Dräger P/N DESCRIPTION Vamos Mount Adapter Plate DU-DR Dash Rev A 2/13/02 GCX Corp. Page 5 of 13
6 Attachment of Power Supply Hanger for Vamos Separate Power Supply 1. Locate tapped holes on bottom of Pivot Arm to attach Power Supply Hanger. Tapped Holes 2. Align thru holes on Power Supply Hanger with tapped holes on Pivot Arm and secure using #10-32 x ½ SHCS (3). Power Supply Hanger #10-32 X ½ SHCS (3) Thru Holes DU-DR Dash Rev A 2/13/02 GCX Corp. Page 6 of 13
7 Attachment of Power Supply Bracket 1. Locate tapped holes for attaching Power Supply Bracket to Power Supply Hanger. Tapped Holes 2. Guide Power Supply Holster onto hanger and secure with #10-32 x ¼ 100 FHMS (4). Note: Power Supply Holster can be mounted either vertically or horizontally. (Vertical) (Horizontal) Power Supply Bracket #10-32 x ¼ 100 FHMS (4) DU-DR Dash Rev A 2/13/02 GCX Corp. Page 7 of 13
8 Attachment of Power Supply and Nylon Retainer 1. Place power supply in Bracket as shown. Insert end of Velcro Straps through ring, pull the strap tight, and press firmly. Velcro Straps (2) 2. Loop power cable through Nylon Retainer. Fasten the Nylon Retainer to the bottom of the bracket using the #8 flat washer and #8-32 x ¼ PHMS included. #8 Flat Washer and #8-32 x ¼ PHMS Nylon Retainer PARTS LIST GCX P/N Dräger P/N DESCRIPTION WM MM15286 Power Supply M-Series Hanger w/ Velcro Straps INSTALLATION - Dash 3000/4000 Slide DASH into Pivot Arm Mounting Plate 1) Align the mounting adapter located at the bottom of the DASH with the edge of Mounting Plate. Slide the DASH into the plate until it stops at the Spring Plunger (located below the Mounting Plate). Pull the Spring Plunger and continue to slide the DASH until the mounting adapter engages the Spring Plunger. DU-DR Dash Rev A 2/13/02 GCX Corp. Page 8 of 13
9 Dash 3000 / 4000 on Top Shelf 1. Dräger Fabius GS Generic Top Plate with 21 Channel The purpose of these instructions is to: 1. Describe attachment of Fabius GS Top Plate. 1. Find the threaded inserts by locating the (4) dimples in the top of the anesthesia machine. If you have difficulty finding the dimples, use the top shelf as a template, and mark the top of the machine in the locations indicated. 2. Drill in the locations marked in step #1 (only where dimples are present), using a ¼ (6,3 mm) diameter drill bit. Drill bit should not penetrate material more than ¼ (6,3 mm). Drilling too deeply will damage insert threads and internal components of the machine. Remove all drilling chips. Location of threaded inserts Top Shelf 3. Run the M5 x 30mm Pan Head Machine Screws (4) through the Top Plate and into the holes drilled in step #2. M5 x 30mm PHMS (4) GS Top Plate 21 Top Channel DU-DR Dash Rev A 2/13/02 GCX Corp. Page 9 of 13
10 1. Low profile 10 Degree Horizontal Mount for Dash 3000 / 4000 without Dashport Tools Required: Philips head screw driver Install 10 Degree Horizontal Channel Mount into Channel 1) Align the Slide of the mount with edge of the Horizontal Channel insert into channel. Tighten the (2) #8-32 x 7/16 PHMS to secure position of the mount in the Channel. 2. Using Low Profile Tilt / Swivel Mount for Dash 3000 / 4000 w/o Dashport Tools Required: Philips head screw driver Install Low Profile Tilt / Swivel Mount into Channel 1) Align the Slide of the mount with edge of the Horizontal Channel insert into Channel. Tighten the (2) #8-32 x 7/16 PHMS to secure position of the mount in the Channel. Slide DASHPort into Mounting Plate 1) If necessary, install DASHPort Spacer per GCX Installation Instructions (DU-ME ) included with the Spacer. 2) Align the mounting adapter located at the bottom of the DASH 4000 DASHPort with the edge of Mounting Plate. Slide the DASHPort into the plate until it stops at the Spring Plunger (located below the Mounting Plate). Pull the Spring Plunger and continue to slide the DASHPort until the mounting adapter engages the Spring Plunger. Spring Plunger PARTS LIST GCX P/N Dräger P/N DESCRIPTION DR HZ HZ MM15738 MM15693 Fabius GS Generic Top Plate w/ 21 Channel Low Profile 10 Degree Horizontal Mount Low Profile Tilt / Swivel Mount DU-DR Dash Rev A 2/13/02 GCX Corp. Page 10 of 13
11 CWS 15 Recall Right side 1. Install CWS 15 onto Subplate Subplate 1) Locate the four M4 threaded studs beneath the CWS15 keyboard bracket. M4 Studs 2) Align the M4 studs with the through holes on the Subplate, place the CWS15 then secure using supplied (4) M4 Kep Nuts. M4 Studs M4 Kep Nuts (4) Subplate DU-DR Dash Rev A 2/13/02 GCX Corp. Page 11 of 13
12 2. Install Pivot Arm into Channel Tools required: Hex Key (1/8 ) 1. Guide Pivot Arm slide into Channel as shown 2. The Slide has (2) 1 / 4 20 x ¾ SHSS set screws that, when tightened, secure the Arm at the desired location within the Channel. PARTS LIST GCX P/N Dräger P/N DESCRIPTION DR MM M Series Pivot Arm for CWS15 DU-DR Dash Rev A 2/13/02 GCX Corp. Page 12 of 13
13 INSTRUCTIONS FOR USE M Series Pivot Arm Pivot 1) To pivot the Arm (near the wall), simply push on the side of the Arm or mounted device. 2) To adjust the pivot tension at the Slide, use a ½ (or 13mm) socket driver to tighten or loosen the Pivot Tension Bolt to obtain the desired tension. Swivel Pivot Tension Bolt 1) To rotate the device simply push or pull the corners of the device. 2) To adjust the swivel tension, use a ½ (or 13mm) socket driver to tighten or loosen the Swivel Tension Adjustment Bolt located on top of the front end of the Arm. Swivel Tension Bolt Cable Management 1) An open cavity beneath the arm with flexible cable covers manage cables going to and from the front and rear of the arm. Flexible Cable Covers Cleaning 1) The mounting assembly may be cleaned with most mild, non-abrasive solutions commonly used in the hospital environment (e.g. diluted bleach, ammonia, or alcohol solutions). 2) The surface finish will be permanently damaged by strong chemicals and solvents such as acetone and trichloroethylene. 3) Steel wool or other abrasive material should never be used. 4) Damage caused by the use of unapproved substances or processes will not be warranted. To verify compatibility, It is recommended that any cleaning solution be tested on a small area of the arm that is not visible. 5) Never submerge the mounting arm. Wipe any cleaning agents off of the arm immediately, using a water-dampened cloth. Dry the arm thoroughly after cleaning. CAUTION: GCX makes no claims regarding the efficacy of the listed chemicals or processes as a means for controlling infection. Consult your hospital s infection control officer or epidemiologist. To clean or sterilize mounted devices or accessory equipment, refer to the specific instructions supplied with those products. DU-DR Dash Rev A 2/13/02 GCX Corp. Page 13 of 13
Installation Guide Philips MP2 IntelliVue M-Series Arm (12'' or 8'') Rail Mount Kit
Installation Guide Philips MP2 IntelliVue M-Series Arm (12'' or 8'') Rail Mount Kit The purpose of this guide is to: 1. Describe mounting of MP2 equipment on Mounting Bracket (page 2). 2. Describe mounting
More informationInstallation Guide. Philips IntelliVue MP20/30/40/50/60/70, MX400/450/600/700/800 Low Profile Camlock Mount
Installation Guide Philips IntelliVue MP20/30/40/50/60/70, MX400/450/600/700/800 Low Profile Camlock Mount The purpose of this guide is to: 1. Describe mounting of Philips Table Top Mount on Table Top
More informationInstallation Guide Stack Mount Kit for Philips G5 and MP5/20/30/40/50/60/70 Monitor
Installation Guide Stack Mount Kit for Philips G5 and MP5/20/30/40/50/60/70 Monitor The purpose of this guide is to describe installation of the Stack Mount. Parts Reference The following parts and hardware
More informationGCX Mounting Assembly Installation Guide. Philips MP90 (M8010A) Mounting Kit for Drager Zeus
GCX Mounting Assembly Installation Guide Philips MP90 (M8010A) Mounting Kit for Drager Zeus The purpose of this guide is to: 1. Describe attachment of Down Post to Arm. 2. Describe attachment of Arm to
More informationInstallation Guide Roll Stand Kit for Philips MP20/30 Monitor
Installation Guide Roll Stand Kit for Philips MP20/30 Monitor The purpose of this guide is to: 1. Describe attachment of Post to Base (page 2). 2. Describe attachment of the Utility Basket to the Roll
More informationInstallation Guide GE Healthcare Carescape Single Display Roll Stand Kit
Installation Guide GE Healthcare Carescape Single Display Roll Stand Kit The purpose of this guide is to describe assembly of the Roll Stand. WARNING - EXCESSIVE LEAKAGE CURRENT - DO NOT use multiple socket
More informationInstallation Guide Philips MP90 Mounting Kit with 16'' M-Series Arm for Datex Ohmeda Avance Anesthesia Machine
Installation Guide Philips MP90 Mounting Kit with 16'' M-Series Arm for Datex Ohmeda Avance Anesthesia Machine The purpose of this guide is to describe installation of the Mounting Kit on the anesthesia
More informationInstallation Guide. Xprezzon Roll Stand
3875 Cypress Drive Petaluma, CA 94954 800.228.2555 707.773.1100 Fax 707.773.1180 www.gcx.com Installation Guide Xprezzon Roll Stand The purpose of this guide is to describe assembly of the Roll Stand and
More informationInstallation Guide GE Healthcare Carescape Dual Display Roll Stand Kit
Installation Guide GE Healthcare Carescape Dual Display Roll Stand Kit The purpose of this guide is to describe assembly of the Roll Stand. WARNING - EXCESSIVE LEAKAGE CURRENT - DO NOT use multiple socket
More informationInstallation Guide. Philips MP20/30/40/50 IntelliVue VHM Wall Mount Kit
Installation Guide Philips MP20/30/40/50 IntelliVue VHM Wall Mount Kit The purpose of this guide is to: 1. Describe attachment of Table Top Mount to Mounting Adapter. 2. Describe attachment of Mounting
More informationInstallation Guide Folding L-Bracket with Display Mounting Extension and Keyboard Tray for M-Series or VHM Arm
3875 Cypress Drive Petaluma, CA 94954 800.228.2555 707.773.1100 Fax 707.773.1180 www.gcx.com Installation Guide Folding L-Bracket with Display Mounting Extension and Keyboard Tray for M-Series or VHM Arm
More informationInstallation Guide Roll Stand Kit 2''/5.1cm Diameter Post with Tilt/Swivel Mounting Plate, Handle, Utility Basket and 10lbs/4.
3875 Cypress Drive Petaluma, CA 94954 800.228.2555 707.773.1100 Fax 707.773.1180 www.gcx.com Installation Guide Roll Stand Kit 2''/5.1cm Diameter Post with Tilt/Swivel Mounting Plate, Handle, Utility Basket
More informationInstallation Guide Philips MP90 Dual Display Mounting Kit for Dräger Apollo Anesthesia Machine
Installation Guide Philips MP90 Dual Display Mounting Kit for Dräger Apollo Anesthesia Machine The purpose of this guide is to describe installation of the Mounting Kit on the anesthesia machine. Parts
More informationInstallation Guide VHM Wall Mount Kit for Philips MX600/700/800 and MP60/70 IntelliVue
Installation Guide VHM Wall Mount Kit for Philips MX600/700/800 and MP60/70 IntelliVue The purpose of this guide is to: 1. Describe attachment of Table Top Mount to Mounting Adapter (page 2). 2. Describe
More informationInstallation Guide LiDCO Hemodynamic Monitor - Roll Stand Kit (US Version)
Installation Guide LiDCO Hemodynamic Monitor - Roll Stand Kit (US Version) The purpose of this guide is to describe assembly of the roll stand kit and mounting of applicable devices. Table of Contents.0
More informationInstallation Guide LiDCO Hemodynamic Monitor - Roll Stand Kit (EURO Version)
Installation Guide LiDCO Hemodynamic Monitor - Roll Stand Kit (EURO Version) The purpose of this guide is to describe assembly of the roll stand kit and mounting of applicable devices. Table of Contents.0
More informationInstallation Manual for Philips Intellivue MP5/20/30 VHM-25 Channel Mount Kit
3875 Cypress Drive Petaluma, CA 94954 800.228.2555 707.773.1100 Fax 707.773.1180 www.gcx.com Installation Manual for Philips Intellivue MP5/20/30 VHM-25 Channel Mount Kit Install Time: 10-15 minutes The
More informationInstallation Manual for Philips SureSigns VS3/VS4/VM4/VM6/VM8/VSV VHM-25 Countertop Mount
3875 Cypress Drive Petaluma, CA 94954 800.228.2555 707.773.1100 Fax 707.773.1180 www.gcx.com Installation Manual for Philips SureSigns VS3/VS4/VM4/VM6/VM8/VSV VHM-25 Countertop Mount Install Time: 20-30
More informationInstallation Guide VHM Arm Kit for Philips Heartstart MRx and Heartstart XL+
Installation Guide VHM Arm Kit for Philips Heartstart MRx and Heartstart XL+ The purpose of this guide is to: 1. Describe installation of Arm in channel (page 2). 2. Describe mounting of defibrillator
More informationInstallation Guide GE Mini Telemetry Receiver Rear Column Mount
3875 Cypress Drive Petaluma, CA 94954 800.228.2555 707.773.1100 Fax 707.773.1180 www.gcx.com Installation Guide GE Mini Telemetry Receiver Rear Column Mount Parts Reference The following parts and hardware
More informationInstallation Guide Variable Height Roll Cart for Corometrics/GE 250 Series Fetal Monitor with Dual Displays and Keyboard Mounts
3875 Cypress Drive Petaluma, CA 94954 800.228.2555 707.773.1100 Fax 707.773.1180 www.gcx.com Installation Guide Variable Height Roll Cart for Corometrics/GE 250 Series Fetal Monitor with Dual Displays
More informationInstallation Manual for VHM-25 Series Arms Channel Mount
3875 Cypress Drive Petaluma, CA 94954 800.228.2555 707.773.1100 Fax 707.773.1180 www.gcx.com Installation Manual for VHM25 Series Arms Channel Mount Install Time: 1015 minutes The purpose of this manual
More information(Refer to qualified personnel)
3875 Cypress Drive Petaluma, CA 94954 800.228.2555 +1.707.773.1100 Fax 707.773.1180 www.gcx.com Installation Guide VHM-P (Non-Locking) and VHM-PL (Locking) Variable Height Arm (Slide-Above-Arm Configuration)
More informationVHM-P (Non-Locking) and VHM-PL (Locking) Variable Height Arm with Slide-In Mounting Plate
3875 Cypress Drive Petaluma, CA 94954 800.228.2555 +1.707.773.1100 Fax 707.773.1180 www.gcx.com VHM-P (Non-Locking) and VHM-PL (Locking) Variable Height Arm with Slide-In Mounting Plate (Refer to qualified
More information3875 Cypress Drive Petaluma, CA Fax
3875 Cypress Drive Petaluma, CA 94954 800.228.2555 +1.707.773.1100 Fax 707.773.1180 www.gcx.com VHM-P (Non-Locking) Variable Height Arm with Fixed Angle Front End for Flat Panel / Keyboard Bracket (L Brackets
More informationVHM-P (Non-Locking) Variable Height Arm with VESA Mounting Plate for 75 x 75mm or 100 x 100mm applications
3875 Cypress Drive Petaluma, CA 94954 800.228.2555 +1.707.773.1100 Fax 707.773.1180 www.gcx.com VHM-P (Non-Locking) Variable Height Arm with VESA Mounting Plate for 75 x 75mm or 100 x 100mm applications
More informationInstallation Guide Corometrics/GE 250 Series Fetal Monitor Roll Cart with Laptop and Display Mounts
3875 Cypress Drive Petaluma, CA 94954 800.228.2555 707.773.1100 Fax 707.773.1180 www.gcx.com Installation Guide Corometrics/GE 250 Series Fetal Monitor Roll Cart with Laptop and Display Mounts Table of
More informationGE CARESCAPE Monitor B650 on VHM- PL Variable Height Arm Channel Mount with Vertical Position Lock
GE CARESCAPE Monitor B650 on VHM- PL Variable Height Arm Channel Mount with Vertical Position Lock PRODUCT DETAILS VHM-PL (Locking) Variable Height Arm with 14" / 35.6 cm Extension and Slide-In Mounting
More informationInstallation Guide. Philips MP90 M-Series Wall Mount Kit (12'' Pivot Arm) Section 1.0: Mounting the M-Series Arm Parts Reference...
Installation Guide Philips MP90 M-Series Wall Mount Kit (12'' Pivot Arm) The purpose of this guide is to describe installation of the MP90 M-Series Wall Mount Kit. Table of Contents Section 1.0: Mounting
More informationCondor Manual. Corporation
Condor Manual Corporation PREFACE IMPORTANT, PLEASE READ CAREFULLY Thank you for your purchase with Amico Accessories Inc. This unit is designed for long lasting performance, providing the end user complies
More informationInstallation Guide Philips MP90 VHM Wall Mount Kit
Installation Guide Philips MP90 VHM Wall Mount Kit The purpose of this guide is to describe the procedures for installing the MP90 VHM Wall Mount Kit. Table of Contents Section 1.0: Mounting the VHM-Series
More informationGCX Mounting Assembly Installation Guide Philips MP90 (with AGM) Mounting Kit for Datex Ohmeda Aestiva Anesthesia Machine
GCX Mounting Assembly Installation Guide Philips MP90 (with AGM) Mounting Kit for Datex Ohmeda Aestiva Anesthesia Machine The purpose of this guide is to: 1. Describe mounting of the 7'' Channel. 2. Describe
More information3875 Cypress Drive Petaluma, CA Fax
3875 Cypress Drive Petaluma, CA 94954 800.228.2555 707.773.1100 Fax 707.773.1180 www.gcx.com GCX Mounting Assembly Installation Guide Datex-Ohmeda Aestiva Display Arm Mounting Kit for Philips IntelliVue
More informationInstallation Instructions. ARS (Amico Rail Systems)
Installation Instructions ARS (Amico Rail Systems) w w w. a m i c o. c o m Preface Important, Please Read Carefully Thank you for your purchase with Amico Accessories Inc. This unit is designed for long
More informationINSTRUCTIONS INSTRUCCIONES CONSIGNES
AUTOMOTIVE PRODUCTS, INC. INSTRUCTIONS INSTRUCCIONES CONSIGNES APPLICATION: 2013-UP FORD ESCAPE APP PART # 28-21010, 28-21015 STYLIZED RUNNING BOARD ITEM QUANTITY DESCRIPTION TOOLS NEEDED 1 2 RUNNING BOARDS
More informationINSTALLATION INSTRUCTIONS RATTLER STEEL RUNNING BOARDS FORD TRANSIT VAN (FULL SIZE)
INSTALLATION INSTRUCTIONS PARTS LIST: 1 32-inch Steel Running Board 1 8-1.25mm x 35mm Hex Bolt 1 96-inch Steel Running Board 13 8-1.25mm x 25mm Hex Bolt 5 Passenger Side/Driver Side Mounting Brackets 20
More informationUniversal Pitch Adjustable Wall Mount For Flat Panel Display UPM-2401
INSTALLATION INSTRUCTIONS Universal Pitch Adjustable Wall Mount For Flat Panel Display UPM-2401 Your new Chief Universal Pitch-Adjustable Wall Mount (UPM-2401) is a quick disconnect mounting system with
More information6 6mm Nylon Lock Nuts 4 12mm Lock Washers 12 6mm Hex Nuts 4 12mm x 32mm x 3mm Flat Washers. (2) 12mm x 40mm Narrow Bolt Plates (Rear)
PARTS LIST: ALUMINUM VIEWPOINT RUNNING BOARDS 1 Driver/Left Running Board 4 12mm Hex Nuts 1 Passenger/Right Running Board 2 10mm Lock Washers 1 Driver/Left Mounting Bracket 2 10mm x 30mm x 2.5mm Flat Washers
More informationCAN AM. Version 1. Version Outlander 400, 500, 650, 800 and Outlander Max Renegade 500/ Outlander 800R/1000R
CAN AM 00-4 Outlander 400, 500, 50, 800 and Outlander Max 007-4 Renegade 500/800 0-4 Outlander 800R/000R BLADE HARDWARE MOUNTING INSTRUCTIONS P/N: 450-04 CUSTOMER MUST RECEIVE A COPY OF THIS INSTRUCTION
More informationUniversal Pitch-Adjustable Wall Mount For Flat Panel Display PLP-91/D
INSTALLATION INSTRUCTIONS Universal Pitch-Adjustable Wall Mount For Flat Panel Display PLP-91/D Your new Wall Mount (PLP-91/D) is a quick disconnect mounting system with adjustability between 0 and 15
More informationAssembly Instructions
Assembly Instructions Part Number Description Model Approx. Assembly Time 99994-049 Cab Enclosure MULE SX 3-4 Hours WARNING Improper installation of this accessory could result in an accident causing serious
More informationThe steering column is of a modular construction and features easy to service electrical switches.
file://c:\tso\tsocache\vdtom_5368\svk~us~en~file=svkb4a01.htm~gen~ref.htm Page 1 of 3 Section 11-04A: Steering Column, Ranger DESCRIPTION AND OPERATION 1997 Ranger Workshop Manual Steering Column NOTE:
More informationPFadvantage MF 6850/6855; Ideal 9080/9090
MF 6850/6855; Ideal 9080/9090 Note: Indented items indicate parts included in an Quantity by Model assembly listed above MF Ideal Part Name/Description Part Number 6850 6855 9080 9090 Instruction Kit MF
More informationINSTALLATION INSTRUCTIONS RATTLER STEEL RUNNING BOARDS DODGE RAM 1500 REGULAR CAB REGULAR CAB
INSTALLATION INSTRUCTIONS PARTS LIST: 2 Steel Running Boards 3 12mm Hex Nuts 1 Driver/Left Mounting Bracket 4 10-1.5mm x 35mm Hex Bolts 1 Driver/Left Support Bracket 4 10mm x 27mm OD x 3mm Flat Washers
More informationPlasma Dual Swing-Out (PDS Series) Wall Mount
INSTALLATION INSTRUCTIONS Plasma Dual Swing-Out ( Series) Wall Mount The wall mount is a rugged, versatile, and installer-friendly solution to unique display mounting requirements. In addition to providing
More informationInstallation Instructions QUARTER STICK Fits: 2 Speed (Powerglide) or 3 Speed (Turbo-Hydramatic)
Installation Instructions QUARTER STICK Fits: 2 Speed (Powerglide) or 3 Speed (Turbo-Hydramatic) Catalog# 3160020 WORK SAFELY! For maximum safety, perform this installation on a clean, level surface and
More informationPFadvantage JD 3300/4400/6600/7700; 4420
Ag Leader Technology Combine Installation JD 33//66/77; 2 Note: Indented items indicate parts included Quantity by Model in an assembly listed above Early Late Part Name/Description Part Number 3 3 6 6
More informationInternational Scout Traveler Installation Instructions
International Scout Traveler Installation Instructions Tools needed: 9/64 drill bit 1/8 drill bit #2 Philips bit for drill Tape measure Pencil Drill #3 Philips Screwdriver #2 Philips Screwdriver Utility
More informationINSTALLATION INSTRUCTIONS RATTLER STEEL RUNNING BOARDS DODGE RAM 1500/ CREW CAB
INSTALLATION INSTRUCTIONS RATTLER STEEL RUNNING BOARDS PARTS LIST: 1 Driver/Left Steel Running Boards 5 12mm Lock Washers 1 Passenger/Right Steel Running Boards 5 12mm Hex Nuts 1 Driver/Left Mounting Bracket
More informationTIP-OUT GLASS WINDSHIELD KIT
TIP-OUT GLASS WINDSHIELD KIT P/N 2881108 APPLICATION Verify accessory fitment at Polaris.com. BEFORE YOU BEGIN Read these instructions and check to be sure all parts and tools are accounted for. Please
More informationFOR WALL MOUNT COMBINATION ARMS
INSTALLATION MANUAL FOR WALL MOUNT COMBINATION ARMS LIGHT DUTY ARMS HEAVY DUTY ARMS KEYBOARD TRAY VERSION Weight Capacity 4-20 lbs KEYBOARD TRAY VERSION Weight Capacity 8-40 lbs WORKSTATION VERSION Weight
More informationInstruction Sheet Kit Number:
Instruction Sheet Kit Number: 72101800 TRACK CONVERSION KIT For All Wheel-Drive 921000 Models WARNING: FAILURE TO FOLLOW INSTRUCTIONS could result in personal injury and/or damage to unit. Read, understand,
More informationE Series Enclosures Installation Instructions (UL /UL2416 E Series Equipment Cabinet/Rack)
E Series Enclosures Installation Instructions (UL60950-1/UL2416 E Series Equipment Cabinet/Rack) WeRackYourWorld.com 1-866-TRY-GLCC (879-4522) Instructions for the following Great Lakes Enclosures: GL720E-2432,
More informationINSTALLATION INSTRUCTIONS RATTLER STEEL RUNNING BOARDS DODGE RAM 1500 QUAD CAB
INSTALLATION INSTRUCTIONS PARTS LIST: 2 Steel Running Boards 5 12mm Lock Washers 1 Driver/Left Mounting Bracket 5 12mm Hex Nuts 1 Driver/Left Center Mounting Bracket 6 10-1.5mm x 35mm Hex Bolts 2 Driver/Left
More informationMOUNT BRACKET PARTS and HARDWARE: Installation parts with * come loose in hardware kit bag. Other parts are preassembled
INSTALL INSTRUCTIONS C-DMM-2006 Dash Monitor Mount 2017-2019 F-250, 350, 450 Pickup, F-450 and 550 Cab Chassis, 2015-2019 Ford F-150 and 2018-2019 Expedition Notes: 1. The C-DMM-2000 series Dash Monitor
More informationDriver Side Support Bracket pictured in "no-tow hook" direction. Reverse direction for tow hook equipped vehicles
PARTS LIST: 1 Bull Bar 2 10-1.5mm x 35mm Hex Bolts 2 Tube Brackets (Bull Bar) passenger or driver side 2 10mm Lock Washers 2 Upper Frame Brackets (models w/o tow hooks only) 4 10mm x 27mm OD x 3mm Flat
More informationPart Name/Description Part Number Quantity Instruction Kit Metalfor Flow Sensor
NOTE: Indented items indicate parts included in an assembly listed above Part Name/Description Part Number Quantity Instruction Kit Metalfor 4101091 1 Flow Sensor 4001356 1 Deflector plate 2000612-1 1
More informationTEL:1-866-XANATOS. INSTALLATION INSTRUCTIONS PART#: SR-DOR SPARTAN RUNNING BOARD DODGE PROMASTER 136 /159 wheel base 14-UP
TEL:1-866-XANATOS INSTALLATION INSTRUCTIONS PART#: SR-DOR303285 SPARTAN RUNNING BOARD DODGE PROMASTER 136 /159 wheel base 14-UP PARTS LIST: 1 Driver/left Spartan Running Board 12 8-1.25mm x 25mm Hex Bolts
More information2 Driver/left Front/Rear Mounting Brackets 6 10mm Lock Washer 2 Passenger/right Front/Rear Mounting 6 10mm Hex Nuts
PARTS LIST: STX300 RUNNING BOARD BRACKET KIT 2 Driver/left / Mounting Brackets 6 10mm Lock Washer 2 Passenger/right / Mounting 6 10mm Hex Nuts Brackets 1 Driver/left Center Mounting Bracket 12 8-1.25mm
More informationRANGER 900 POWER STEERING KIT
RANGER 900 POWER STEERING KIT P/N 2880083 APPLICATION MY14 AND NEWER RANGER XP 900 MODELS IMPORTANT It is strongly recommended that this kit be installed by an authorized Polaris dealer. NOTE Use of this
More informationINSTALLATION INSTRUCTIONS Product Revision Form Rev. C INST-439 CRADLE, DELL E-6510/6500
7160-0202 Cradle is designed to be used with a Dell E-Port or E-Port Plus Port Replicator. The cradle is assembled for used with Dell E-6510. By removing 2 Side Spacers the Cradle can also be used with
More informationINSTALLATION INSTRUCTIONS SEMI-HIDDEN WINCH MOUNT Part Number:70005 Application: Ford Super Duty
INSTALLATION INSTRUCTIONS SEMI-HIDDEN WINCH MOUNT Part Number:70005 Application: Ford Super Duty Your safety, and the safety of others, is very important. To help you make informed decisions about safety,
More informationINSTALLATION INSTRUCTIONS 5" OVAL WHEEL TO WHEEL SIDEBARS DODGE RAM MEGA CAB 6-1/2FT BED
INSTALLATION INSTRUCTIONS PARTS LIST: 1 Driver/Left Sidebar 8 10-1.5mm x 35mm Hex Bolts 1 Passenger/Right Sidebar 8 10mm x 27mm OD x 3mm Flat Washers 1 Driver Mounting Bracket 8 s 1 Driver Support Bracket
More informationPFadvantage Metalfor Araus 1360
Metalfor Araus 1360 Note: Indented items indicate parts included in an assembly listed above Part Name/Description Part Number Quantity Instruction Kit Metalfor Araus 2005300-14 1 Display Bracket 4000134
More informationINSTALLATION & OWNER S MANUAL
Rev. B, p. 1 of 25 INSTALLATION & OWNER S MANUAL POLARIS RANGER RCS (for models XP or HD) (for model years 2009-) cab without doors kit (p/n 1POLRCWD) cab with doors kit (p/n 1POLRC) doors only kit (p/n
More informationINSTALLATION MANUAL
INSTALLATION MANUAL 1500350 Parts List 1 Driver / left inner fender liner 1 Passenger / right inner fender liner 4 Z-hanger brackets 1 Thread-set bolt, M6 1 Thread-set washer 1 Thread-set spacer 22 Hex
More informationSYSTIMAX SMB-4-3/4, SMB-8-1/2 Shelf-Mounted Cable Bracket Kits and 1000G2-XCPB Expanded Cable Protector Kit
Instruction Sheet 860380799 SYSTIMAX Solutions SYSTIMAX SMB-4-3/4, SMB-8-1/2 Shelf-Mounted Bracket Kits and 1000G2-XCPB Expanded Protector Kit General The SYSTIMAX SMB-4-3/4 and SMB-8-1/2 shelf mounted
More informationCAUTION. INSTALLATION INSTRUCTIONS Part Number Hidden Winch Kit with special XD 9000 Short Drum Winch For Ford F-150 Truck
INSTALLATION INSTRUCTIONS Part Number 69110 Hidden Winch Kit with special XD 9000 Short Drum Winch For Ford F-150 Truck As you read these instructions, you will see NOTES, CAUTIONS and WARNINGS. Each message
More informationUltra Elite Facepiece: AirHawk II Air Mask
Ultra Elite Facepiece: AirHawk II Air Mask MAINTENANCE AND REPAIR MSA 713 (L) Rev. 1 MSA 2017 Prnt. Spec. 10000005389(I) Mat. 10104249 Doc. 10104249 PARTS LIST Ultra Elite Facepiece (Complete) Item P/N
More informationWARNING! THIS SHIFTER IS FOR RACING USE ONLY. NOT FOR STREET USE!
Installation Instructions Quarter Stick Shifter Fits: GM Powerglide w/forward or reverse valve body. Also fits: TH250, TH350, TH375 and TH400 Auto transmissions w/reverse valve body. Catalog# 3162020 WORK
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory TWO-PIECE POLY (HARD COAT) P/N 0SR71-HL4-A00 Application SXS1000M/M3P/M5D/M5P Honda Dealer: Please give a copy of these instructions to your customer. Publication No.
More informationLexus ES Fine Mesh and Adaptive Cruise Control Fine Mesh Grilles Upper and Lower Replacements
IMPORTANT: PLEASE KEEP THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE! 2013-15 Lexus ES Fine Mesh and Adaptive Cruise Control Fine Mesh Grilles Upper and Lower Replacements Part #1372-0102-13 / Black Ice
More informationINSTALLATION INSTRUCTIONS PART#: SR-GMR13796 SPARTAN RUNNING BOARD CHEVY EXPRESS 1500/2500/3500 GMC SAVANNA 1500/2500/ UP
INSTALLATION INSTRUCTIONS PART#: SR-GMR13796 SPARTAN RUNNING BOARD CHEVY EXPRESS 1500/2500/3500 GMC SAVANNA 1500/2500/3500 03-UP PARTS LIST: 1 Driver Side- 37 Spartan Running Board 8 12mm Hex Nuts 1 Passenger
More informationInstallation Instructions
by Installation Instructions For: CJ5 (1955-1975) and M38, A1 (1951-1971) Part Number 51405 WARNING This product is designed primarily to enhance the appearance of the vehicle and to shield the occupants
More information* * E996L Series. E996L for Rim/Vertical. E996L for Mortise CAUTION
*921297-00* 921297-00 Electric Locking Trim E996L Series Installation Instructions CAUTION Product is shipped in Fail Safe (FS) configuration. Fail Safe configuration is required by code in some applications
More informationSCION xd INTERIOR LIGHTING UPGRADE Preparation
Preparation Part Number: PTS21-52085 Light Guide Kit Contents Item # Quantity Reqd. Description 1 1 Controller Board, 4 color programmed w/ Bracket 2 1 RGB, LED Engine wire harness 3 2 14mm Light Rod,
More information200 Shadylane Drive Philipsburg, PA Phone: (814) Fax: (814) Service Manual. Model 642E Centrifuge
200 Shadylane Drive Philipsburg, PA 16866 Phone: (814) 342-6205 Fax: (814) 342-4510 www.druckerdiagnostics.com Service Manual Model 642E Centrifuge MODEL 642E SERVICE MANUAL REV: Original Issue 1 CONTENTS
More information11-16 Jeep Grand Cherokee 4 Oval Sidebars
Page 1/6 Part #11594.04 Passenger/Right Rear Inner Support Bracket (4) 12mm x 40mm Bolt Plates Driver/Left Rear Inner Support Bracket (2) 10mm x 35mm Long Bolt Plates (2) 10mm x 35mm Short Bolt Plates
More informationSPECIALTY TOP CO. STC. INSTALLATION INSTRUCTIONS TOYOTA FAST TRAC Z TOP Toyota FJ PART #222-31X 82 1/8" 82 1/8"
STC INSTALLATION INSTRUCTIONS TOYOTA FAST TRAC Z TOP Toyota FJ-40 1963-1983 PART #222-31X SPECIALTY TOP CO. Thank you for purchasing Specialty's Convertible Top for your Toyota. It has been designed for
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS DESCRIPTION: APPLICATION: PART NUMBER: KIT CONTENTS: Item Qty. A B C D E F G H 1 Bedliner Under Rail Bedliner Titan Crew Cab/King Cab/Single Cab 999T1 W3700, 999T1
More informationPOLY TIP-DOWN WINDSHIELD KIT
POLY TIP-DOWN WINDSHIELD KIT P/N 2881919 APPLICATION Verify accessory fitment at Polaris.com. BEFORE YOU BEGIN Read these instructions and check to be sure all parts and tools are accounted for. Please
More informationK Autoslide & K Autoslide
HJ26077, Rev 16 07/18 5th wheel hitch 6077 18K Autoslide & 6107 21K Autoslide US Pat. 7,506,886 US Pat. 7,753,392 CA Pat. 2,576,427 AS Pat. 2007200421 Important Information WARRANTY POLICY, OPERATOR MANUALS
More informationINSTALLATION DESCRIPTION
The Series 2011xTJ20 / 3000LCxTJ20 is a 1200 pound holding force top jamb-mounted electromagnetic lock designed to secure a single-inswinging door. The lock requires both installation procedures as described
More information2-row and All-row systems included.
Ag Leader Technology Cotton Picker Installation Installation Instructions for John Deere cotton picker models: 2-row and All-row systems included. IMPORTANT: Ensure the model numbers shown above correspond
More informationParts List Continues on Next Page
Assembly Instructions and Owner s Manual Description: Quantum Hardcoated Polycarbonate UTV Windshield, Wash n Wipe Full Size Model: Part Number: N30202 Installation Time: 60 min Polaris RZR 800, Round
More information6/17 HJ26077 Rev 12. US Pat. 7,506,886 US Pat. 7,753,392 CA Pat. 2,576,427 AS Pat PAGE 1
6/17 HJ26077 Rev 12 US Pat. 7,506,886 US Pat. 7,753,392 CA Pat. 2,576,427 AS Pat. 2007200421 PAGE 1 WARRANTY POLICY, OPERATOR MANUALS & REGISTRATION Go online to www.demco-products.com to review Demco
More informationInstallation Instructions Tigertop
Installation Instructions Tigertop Vehicle Application Jeep CJ5 1955 1975 Part Number: 51405 Jeep M38, A1 1951 1971 Part Number: 51405 www.bestop.com - We re here to help! Visit our web site and click
More informationFOR FUTURE REFERENCE SERIES 93HPS
Hypro Series 93HPS Hydraulically Driven Wetseal Multistage Pumps Repair Manual KEEP FOR FUTURE REFERENCE Form L-1578R Rev. A SERIES 93HPS Hydraulically Driven Stainless Steel Multistage Centrifugal Pumps
More informationGround Effects, P/N: (V6), (V8)
, P/N: 92248596 (V6), 92248560 (V8) 3. Open trunk and remove 3 scrivets per side. Retain. Remove LH and RH tail lamp access cover. Retain. Refer to Figure 1. NOTE: Installation is made easier with the
More information<THESE INSTRUCTIONS MUST BE GIVEN TO THE END USER> B&W
B&W Trailer Hitches 1216 Hawaii Rd / PO Box 186 Humboldt, KS 66748 P:620.473.3664 F:620.869.9031 Turnoverball Gooseneck Hitch Installation Instructions
More informationRostselmash Torum 740
Note: Indented items indicate parts included in an assembly listed above Quantity by Model Part Name/Description Part Number 740 Combine Kit Torum 740 4100762 1 Threaded Arm Assembly 2000311-2 1 Header
More informationIMPORTANT SAFETY INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS READ AND FOLLOW ALL SAFETY INSTRUCTIONS! SAVE THESE INSTRUCTIONS AND DELIVER TO OWNER AFTER INSTALLATION To reduce the risk of death, personal injury or property damage from
More information7/18 HJ26077 Rev 16. US Pat. 7,506,886 US Pat. 7,753,392 CA Pat. 2,576,427 AS Pat PAGE 1
7/18 HJ26077 Rev 16 US Pat. 7,506,886 US Pat. 7,753,392 CA Pat. 2,576,427 AS Pat. 2007200421 PAGE 1 WARRANTY POLICY, OPERATOR MANUALS & REGISTRATION Go online to www.demco-products.com to review Demco
More informationInstallation Instructions
Installation Instructions AMP RESEARCH Power Step by Bestop Automatic Retracting Running Board Vehicle Application Nissan Titan King Cab 2004 and newer (5 ft.) Part Number: 75106-01 Nissan Titan Crew Cab
More informationRef Qty Part Description Part Number -1- Kit ( ) Contents:
REAR CANVAS DOOR KIT 900 XP RANGER CREW P/N 2879899 Application RANGER 900 XP CREW Before you begin, read these instructions twice and check to be sure all parts and tools are accounted for. Please retain
More informationRIM Hood For Aeromaster Bodies
RIM Hood For Aeromaster Bodies Service Guide WARNING: Hood should be opened by releasing the hold-down straps, lifting the hood, and engaging the prop rod. Be sure prop rod is properly engaged before working
More informationINSTALLATION INSTRUCTION BULL BAR DODGE RAM 1500 PART NUMBER
INSTALLATION INSTRUCTION 09-12 DODGE RAM 1500 PART NUMBER - 200691 PARTS LIST: Qty Description Qty Description 1 Bull Bar 10 12mm Lock Washers 2 Upper Frame Mounting Brackets (for trucks without tow hooks
More informationFlow Sensor
NOTE: Indented items indicate parts included in an assembly listed above Part Name/Description Part Number Quantity Instruction Kit Metalfor 4101091 1 Quick reference sheet 2002831-36 1 Installation instructions
More informationINSTALLATION & OWNER S MANUAL
INSTALLATION & OWNER S MANUAL INSTALLATION INSTRUCTIONS KAWASAKI MULE 4000 CAB KIT (p/n: KAF40-005WA and KAF40-005BA) NOTE: Hard sided doors are sold separately. This manual is the property of the owner.
More informationEasy Cover. Installation Instructions. Attention Dealers: Please give this owners manual to the customer when the product is delivered.
Serving the Truck & Trailer Industry Since 944 Easy Cover Attention Dealers: Please give this owners manual to the customer when the product is delivered. Call 00-3-94 www.aeroindustries.com Indianapolis,
More information