PFadvantage JD 3300/4400/6600/7700; 4420

Size: px
Start display at page:

Download "PFadvantage JD 3300/4400/6600/7700; 4420"

Transcription

1 Ag Leader Technology Combine Installation JD 33//66/77; 2 Note: Indented items indicate parts included Quantity by Model in an assembly listed above Early Late Part Name/Description Part Number Instruction Kit JD xx, Flow Sensor JD Flow Sensor JD Flow Sensor JD Early 66/ Flow Sensor JD Elevator Deflector Header Sensor Standard Arm Assembly 18-in. rod, S-hook Lower Adjuster Small Black Lower Adjuster Inst. Kit JD xx, Gleaner Decal Do Not Adjust, Use Lower Adjuster! Drill Template Drill bit 13/32 in Transfer punch 13/32 in Square file 5/16 in Bearing 1. in Offset Link Conveyor Chain File handle Alcohol swab packet Cable Kit JD Cable Kit JD Cable Kit JD 33// Cab Cable 1 ft Distribution Cable 12 in Flow Sensor Cable 1 ft Flow Sensor Cable 15 ft Power Cable JD XX2 ft 6 in Elevator Speed Power Cable JD Ground Speed Cable JD /2 ft Elevator Speed Cable JD ft Combine Model Early Models before Serial # Late Models after Serial # PN: December 25 Rev C 1

2 Combine Installation JD 33//66/77; 2 Ag Leader Technology Note: Indented items indicate parts included Quantity by Model in an assembly listed above Early Late Part Name/Description Part Number Cable Inst. Kit JD xx Cable Clamp 3/8 in Alcohol Swab Pack Grey Plastic Cable Clamps Cable Tie 15 in. black Cable Tie 6 in. black Adhesive Mounting Base 2 way Grommet Rubber 1/2 in. ID x 1-3/8 in. P.H.D Grommet Rubber 3/ in. ID x 1-3/8 in. P.H.D Parts Kit JD 33//66/ Header Sensor Inst. Kit JD xx2, xx Clamp Plate xx2 Header Sensor Extension Spring S-Hook Cap screw 5/16 x 1-1/2 in Lock Nut 5/16 in Flat Washer 5/16 in Magnet Collar Assembly 1/38 in. I.D Flow Sensor Inst. Kit JD xx Deflector mounting bar Carriage bolt 5/16 x 2 in Lock nut 5/16 in Split lock washer 5/16 in Monitor Bracket Installation Kit Cap screw 1/ x 1 in Hex nut 1/ in Split lock washer 1/ in Flat washer 1/ in Ground Speed Sensor Kit JD xx Speed Sensor w/2 Socket Tower Jam Nut fine thread, 3/ in Monitor bracket base/ceiling Combine Model Early Models before Serial # Late Models after Serial # December 25 Rev C

3 Ag Leader Technology Combine Installation JD 33//66/77; 2 Note: Indented items indicate parts included Quantity by Model in an assembly listed above Early Late Part Name/Description Part Number Elevator Mount System (EMS) Elevator Mount System (EMS) Elevator Mount Unit RH Standard Battery Power Cable 16 ft EMS EMS Installation Kit Generic Fuse 1.25 x amp Screw Driver Proximity switch / Hex nut / Hex Nylock nut / External tooth lock washer #8 x 3/8 self tapping hex slotted hd screw / x 1-3/ phillips pan hd screw #1 x 1/2" hex slotted hd sheet metal screw Pen Black Permanent EMS Instruction Kit Generic Installation Extras for Narrow Elevators Extension plate Lock nut 1/ in Button head screw 1/ x 1/2 in Moisture Sensor 15 ft Combine Model Early Models before Serial # Late Models after Serial # PN: December 25 Rev C 3

4 Combine Installation JD 33//66/77; 2 Ag Leader Technology Important Notices You will save time and prevent wrong installation of components by closely following these step-by-step instructions. If you have questions, call Ag Leader Technology at x 1. Direction words (LEFT and RIGHT) are commonly used when describing an installation procedure. Interpret direction words as if sitting in operator seat. Signal words (CAUTION, IMPORTANT and NOTE) are provided to draw attention to information that is important for the safe/correct installation and operation of this product. CAUTION will alert you to situations that will impact the physical safety of you or others. IMPORTANT will alert you to the potential for damage to the product or loss of data. NOTE will provide you with additional information to simplify a procedure or clarify a process. Keep parts list and installation instructions for use as a reference after completing installation. Section Contents Item Page Installing Display 5 Installing Cab & Distribution Cables 7 Installing Power Cable 8 Installing Elevator Speed Cable 9 Installing Ground Speed Cable 11 Installing Header Height Sensor 12 Installing Elevator Deflector (66 & 77 models only) 1 Installing Flow Sensor 16 Installing Lower Elevator Adjuster 17 Installing Elevator Mount Unit (EMU) 19 Installing Moisture Sensor 23 Final Inspection 2 Operational Checkout 25 December 25 Rev C

5 Ag Leader Technology Combine Installation JD 33//66/77; 2 Installing Display Parts required for procedure: (1) (1) Ceiling bracket (1) U-bracket (1) Marking pen or scribe (1) Punch (1) Drill bit 13/6 in. (3) Self-tapping screw 1/ x 3/ in. (2) Hex head cap screw 1/ x 3/ in. (2) Split lock washer 1/ in. (2) Hex nut 1/ in. Extra fasteners are provided NOTE: The recommended mounting position is on the cab ceiling as shown in Figure 1. This places the display within easy reach and in a convenient viewing position. Figure 1. Display bracket installed PN: December 25 Rev C 5

6 Combine Installation JD 33//66/77; 2 Ag Leader Technology Step-by-Step Procedure 1. Assemble U-bracket to ceiling bracket as shown in Figure 2. Install display to U-bracket using provided knobs. Figure 2. U-bracket assembled to ceiling bracket 2. Position bracket assembly (with display installed) against ceiling to determine best location and angle for viewing and operation. Mark (2) holes of bracket on ceiling. 3. Remove screws holding radio to cab ceiling and lower radio to verify mounting screws will not interfere with wires or air conditioning lines before drilling holes.. Punch and drill (2) holes through ceiling using provided punch and 9/32 in. drill bit. 5. Remove display from U-bracket and attach bracket assembly to ceiling using 1/ in. cap screws, lock washers and hex nuts. 6. Re-install display to U-bracket. 6 December 25 Rev C

7 Ag Leader Technology Combine Installation JD 33//66/77; 2 Installing Cab & Distribution Cables Parts required for procedure: (1) Cab cable (1) Distribution cable (1) Grommet (1) Alcohol swab packet Plastic cable clips Step-by-Step Procedure 1. Connect 25-pin D-shaped connector of cab cable to mating connector on back of display. IMPORTANT: Never use force to mate electrical connectors. If connectors do not mate easily, they are not aligned properly. 2. Lift right-front corner of cab floor mat to see if 1-3/8 in. diameter knockout in cab floor has been removed. If it is still in place, completely remove it. 3. Push each connector of distribution cable down through hole in floor.. Install grommet (3/ in. I.D.) around wires of distribution cable and insert grommet into hole in floor as shown in Figure 3. Distribution installed Figure 3. Distribution and grommet installed in cab floor PN: December 25 Rev C 7

8 Combine Installation JD 33//66/77; 2 Ag Leader Technology 5. Connect 2-pin plug of cab cable to 2-pin receptacle of distribution cable. 6. Determine desired routing for cab cable from display to floor. Secure cab cable using provided adhesive backed cable clips. Clean surface with alcohol swab before attaching adhesive backed cable clips to ensure good adhesion. Installing Power Cable Parts required for procedure: (1) Power cable Cable ties Step-by-Step Procedure 1. Connect power and ground leads of power cable to batteries. Ensure red fused wire goes to positive terminal and black wire goes to negative terminal. Install ring terminals of power cable to bolts of battery clamps. Check for 12-volt nominal power across terminals. 2. Route power cable to distribution cable by passing it through a hole in plate between engine compartment and area under cab. 3. Connect power cable to mating connector of distribution cable. 8 December 25 Rev C

9 Ag Leader Technology Combine Installation JD 33//66/77; 2 Installing Elevator Speed Cable Parts required for procedure: (1) Elevator speed cable (1) Elevator speed power cable (not required on all machines) Cable ties Step-by-Step Procedure 1. Locate elevator speed sensor at left end of clean grain cross auger. If machine is not equipped with an elevator speed sensor, one must be purchased from a JD dealer and installed as shown in Figure. Figure. Elevator speed sensor on left side of combine 2. Install tee end of elevator speed cable between existing wiring harness and shaft speed sensor. If machine was not originally equipped with elevator speed sensor, only (1) connector of tee connection will be used because combine harness is non-existent. Do not confuse ground speed cable with elevator speed cable. NOTE: For early model combines with round connectors, use provided adapters to connect elevator speed cable to sensor. 3. Tie elevator speed cable to existing low shaft speed sensor and follow harness up. Ensure it is tied securely where it passes under chain sprockets. PN: December 25 Rev C 9

10 Combine Installation JD 33//66/77; 2 Ag Leader Technology. At inlet line for remote hydrostatic charge pump (a small belt driven gear pump), route cable forward along existing electric wiring running parallel to hydrostatic charge pump line after it bends. 5. At 6 in. above charge pump, route elevator speed cable along hydrostatic pump control push/pull cable. Follow to area near distribution cable. 6. Connect elevator speed cable to distribution cable as follows: a. Machines with factory installed elevator speed sensor Simply connect elevator speed cable to mating connector of distribution cable. b. Machines with retrofitted elevator speed sensor Connect elevator speed cable and elevator speed power cable to mating connectors of distribution cable as shown in Figure 5. Elevator speed power cable is required to supply power to sensor since combine harness is non-existent. Figure 5. Elevator speed sensor and cables 1 December 25 Rev C

11 Ag Leader Technology Combine Installation JD 33//66/77; 2 Installing Ground Speed Cable Parts required for procedure: (1) Ground speed cable (1) Ground speed sensor (1) Magnetic collar assembly (2) Hex jam nuts Cable ties NOTE: A magnetic collar assembly and sensor must be installed before ground speed cable can be installed. Parts are provided. Step-by-Step Procedure 1. Install provided magnetic collar assembly and sensor on final drive shaft on right side of machine as shown in Figure 6. Clearance between sensor and magnetic collar assembly should be 1/16 to 1/8-inch. Installer must fabricate bracket for sensor. Magnet Collar Assembly Ground Speed Sensor Final Drive Shaft Figure 6. Magnetic collar installed 2. Connect either end of ground speed cable to ground speed sensor. 3. Route other end of ground speed cable up to distribution cable and connect to mating connector of distribution cable. PN: December 25 Rev C 11

12 Combine Installation JD 33//66/77; 2 Ag Leader Technology Installing Header Height Sensor Parts required for procedure: (1) Header height sensor (1) Arm assembly (1) Extension spring (1) S-hook (1) Clamp plate (2) Cap screw 5/16 x 1-1/2 in. (2) Lock nut 5/16 in. () Flat washer 5/16 in. Cable ties Step-by-Step Procedure 1. Install arm assembly into hole of sensor pivot shaft using a nut and lock washer on each side of shaft. 2. Position header sensor under expanded metal walkway in front of engine compartment as shown in Figure 7 such that: a. Threaded arm is aligned with right side of feeder house. b. Sensor is as far back as it will go under walkway. Figure 7. Header sensor installed 3. Place clamp plate over sensor on top of expanded metal walkway.. Install (2) 5/16 x 1-1/2 in. cap screws through clamp plate and center row of holes in top of sensor frame. 12 December 25 Rev C

13 Ag Leader Technology Combine Installation JD 33//66/77; 2 5. Verify arm alignment and tighten cap screws to secure sensor to walkway. IMPORTANT: Do not apply excessive torque. Sensor frame may deform and prevent proper operation. Tighten nuts just enough to firmly hold sensor in place. Verify arm pivots smoothly and always returns to spring centered position. 6. Remove nut from 5/16-in. cap screw located under right end of feeder house access door. 7. Install S-hook with anchor spring on screw and replace nut. 8. Position S-hook on threaded arm near end of arm and tighten nuts. 9. Connect extension spring to S-hook on arm assembly and S-hook on feeder house. Pinch hooks closed so spring cannot come loose. 1. Hold pivot shaft in spring centered position with a wrench across flats of shaft. Bend threaded arm near pivot shaft until spring has tension. Do this with header fully raised. 11. Route header sensor cable to area under cab by tying it to parking brake cable that is routed just behind walkway. 12. Connect header sensor cable to mating connector of distribution cable. PN: December 25 Rev C 13

14 Combine Installation JD 33//66/77; 2 Ag Leader Technology Installing Elevator Deflector (66/77 only) Parts required for procedure: (1) Stainless steel deflector (1) Deflector mounting bar (1) Drill template (1) Punch (1) Drill bit 13/32 in. (1) Square file (2) Carriage bolt 5/16 x 2 in. (2) Lock washer 5/16 in. (2) Lock nut 5/16 in. (1) Alcohol swab packet (1) Decal Do Not Adjust, Use Lower Adjuster! NOTE: On 66 & 77 models, the corner radius of the elevator head does not match the path of the paddle tips as they rotate about the top sprocket. The provided elevator deflector serves to smooth the flow of grain through the elevator head. In addition, it will likely reduce wear and prolong the life of the elevator head. Step-by-Step Procedure 1. Disconnect belt that drives clean grain elevator countershaft from separator secondary countershaft. Use a crowbar to pull spring-loaded elevator countershaft down until belt that drives it can be removed. 2. Open bottom access door of elevator and turn elevator conveyor chain until connector links or offset links are at bottom of elevator. 3. Adjust top shaft adjuster (2 screws at top of elevator on early machines, rod on back of elevator on late models) to fully lower top shaft.. Remove top door and 5/16 in. cap screw with wing nut from top of elevator. NOTE: If holes that match template are already present on elevator, skip steps 5 thru Use hole from top door latch in top of elevator to install drill template with (1) 5/16 in. cap screw. Ensure template is straight and tighten nut very tight to keep template from moving. 6. Center punch elevator housing at center of (2) square holes in template and drill with 11/32 in. drill bit. 7. File holes square to match holes of template. 1 December 25 Rev C

15 Ag Leader Technology Combine Installation JD 33//66/77; 2 8. Inside clean grain elevator, align deflector plate and deflector mounting bar with holes drilled in Step 6. See Figure 8. Figure 8. Side view of deflector installed 9. Install (2) 5/16 x 2 in. carriage bolts up from inside elevator. 1. Install lock washers and lock nuts on top of elevator just tight enough to bring deflector up against mounting bar. 11. Push deflector plate back so it is tight against back wall of elevator as shown in Figure 8. Fully tighten nuts. 12. Position a paddle directly above sprocket as shown in Figure Re-adjust top shaft of elevator so clearance between tip of paddle and bottom surface of deflector plate is 3/8 to 1/2 in. Ensure top shaft is raised evenly on both sides. It may be necessary to disconnect chain to adjust shaft. IMPORTANT: Failure to do this may result in poor accuracy. Top shaft should not be adjusted again after completing installation 1. Install Do not Adjust! Use Lower Adjuster decal on back of clean grain elevator housing by top shaft adjuster on late models, or at top of elevator on early models (clean housing of dirt and oil so the decal will adhere properly). PN: December 25 Rev C 15

16 Combine Installation JD 33//66/77; 2 Ag Leader Technology Installing Flow Sensor Parts required for procedure: (1) Flow sensor (1) Flow sensor cable Cable ties Step-by-Step Procedure 1. Install flow sensor in place of original cover at top of elevator as shown in Figure 9. Flow sensor housing matches shape of original cover and is secured by original latch and thumbscrew. Figure 9. Flow sensor installed 2. Connect either end of flow sensor cable to flow sensor. 3. Route opposite end of flow sensor cable forward beside grain tank wall and then in front of grain tank wall towards cab.. Route cable forward and down between engine compartment and cab. 5. Connect flow sensor cable to mating connector of distribution cable. 16 December 25 Rev C

17 Ag Leader Technology Combine Installation JD 33//66/77; 2 Installing Elevator Adjuster Parts required for procedure: (1) Elevator adjuster assembly (1) Bearing 1. in. (1) Drill template (1) Punch (1) Drill bit 13/32 in. (1) Square file (1) Offset link elevator chain Step-by-Step Procedure 1. Remove bearing and bearing flanges at lower end of clean grain elevator. 2. Install metal drill template using (3) bolts that secured bearing flanges as shown in Figure 1. Figure 1. Drill template installed 3. Center punch elevator housing at () outside square holes in template using provided transfer punch. Drill holes using provided 13/32 in. drill bit.. File the corners of the holes square to match the template. 5. Remove drill template and install bearing and bearing flanges loosely onto adjuster slide plate. PN: December 25 Rev C 17

18 Combine Installation JD 33//66/77; 2 Ag Leader Technology 6. Mount adjuster loosely to clean grain elevator housing using 3/8 in. carriage bolts as shown in Figure 11. Figure 11. Adjuster installed 7. Reconnect conveyor chain. It may be necessary to add offset links if top shaft has been significantly raised. 8. With cross auger shaft and sprocket suspended on conveyor chain, tighten () bolts of lower adjuster. Conveyor chain is adequately tight when chain cannot be pulled away from sprocket. A little side-to-side movement is okay. 9. Replace belt that drives clean grain elevator countershaft. 18 December 25 Rev C

19 Ag Leader Technology Combine Installation JD 33//66/77; 2 Installing Elevator Mount Unit (EMU) Parts required for procedure: (1) Elevator mount unit (EMU) (1) Marking pen (1) Drill bit 9/32 in. (1) Metal file (5) Pan head screw 1/ x 1-3/ in. (5) External tooth lock washer 1/ in. (5) Hex nut 1/ in. (5) Lock nut 1/ in. () Sheet metal screw #1 x 1/2 in. Additional parts required for narrow elevators (33,, 2): (1) Extension bracket (2) Button head screw 1/ x 1/2 in. (2) Lock nut 1/ in. Step-by-Step Procedure 1. Disassemble plastic spacer block from EMU housing. IMPORTANT: Combines intended for use in rice or grass seed require that a modification be made to outlet hole on plastic spacer block as shown in Figures 12 & 13. If you do not intend to harvest rice or grass, do NOT remove this area Figure 12. Standard Block Figure 13. Modified Block PN: December 25 Rev C 19

20 Combine Installation JD 33//66/77; 2 Ag Leader Technology 2. For 33,, 2 models only, install extension bracket to spacer block as shown in Figure 1. For 66, 77 models, skip to step 3. Extension bracket Figure 1. L-shaped extension bracket installed on spacer block 3. Position spacer block for marking holes as follows: a. For 66, 77 models Position spacer block on side of clean-grain elevator as high as possible and forward as far as center divider of elevator will allow. b. For 33,, 2 models Position spacer block as high as possible and forward on elevator as far as extension bracket will allow.. Carefully trace around inlet and outlet holes using a permanent marker. Use provided 9/32 in. drill bit to mark locations for (5) mounting holes. See Figure 15. For narrow elevators mark (3) remaining holes of spacer block on side of elevator and (2) holes of extension bracket on back of elevator. 5. Extend opening of inlet hole to 8 in. so outline of cutouts on elevator matches cavity on back of spacer as shown in Figure 15. IMPORTANT: Extending dimensions of inlet hole is critical for operation of EMU. If dimensions are not extended, moisture may be inaccurate due to insufficient grain passing by sensor. 6. Drill 1/2 in. holes in all corners of inlet and outlet holes. Drill (5) 9/32 in. holes for mounting EMU to elevator. 2 December 25 Rev C

21 Ag Leader Technology Combine Installation JD 33//66/77; 2 Figure 15. Holes and cutouts marked (95 shown) 7. Cut inlet and outlet holes using an appropriate cutting tool. 8. File edges of holes to remove burrs or sharp edges that may wear chain paddles or prevent clean mounting of EMU. 9. Install mounting screws as follows: a. For 66, 77 models Install external tooth lock washers on (5) 1/ x 1-3/ in. pan head screws and insert into mounting holes from inside elevator. Install hex nuts to keep screws in place. See Figure 16. b. For 33,, 2 models Install external tooth lock washers on (3) 1/ x 1-3/ in. pan head screws and insert into mounting holes on side of elevator. Install hex nuts to keep screws in place. Install extension bracket to back edge of elevator using (2) button head screws and lock nuts. 1. Mount spacer block to elevator as shown in Figure Secure EMU housing on top of spacer block with (5) 1/ in. lock nuts. For 33,, 2 models, (2) 1/ x 1-3/ in. pan head screws must be installed through extension bracket before nuts can be installed. 12. Install () sheet metal screws into remaining mounting holes of spacer block. 13. Reinstall electrical cover to EMU. PN: December 25 Rev C 21

22 Combine Installation JD 33//66/77; 2 Ag Leader Technology Figure 16. Mounting screws installed Figure 17. Spacer block mounted to elevator 22 December 25 Rev C

23 Ag Leader Technology Combine Installation JD 33//66/77; 2 Installing Moisture Sensor Parts required for procedure: (1) Moisture sensor with integral cable (1) Moisture sensor cover (attached to EMU) () #8 x 3/8 in. self-tapping screws Cable ties Step-by-Step Procedure 1. Remove (1) sheet metal screw that attaches aluminum plate to plastic housing of moisture sensor. Install ground terminal strap of moisture sensor on screw as shown in Figure 18. Attached Ground Strap Figure 18. Moisture sensor 2. Feed moisture sensor cable through hole in top of moisture sensor cover from enclosed side out as shown in Figure Slip aluminum housing of moisture sensor into holder until all () holes in aluminum housing line up with () holes in holder.. Install () #8 x 3/8 in. self-tapping screws through holes in moisture sensor holder into aluminum plate of moisture sensor. 5. Install moisture sensor to EMU housing by engaging tab on bottom of moisture sensor holder with tab on side of main housing, tilting sensor upward to insert sensor blade into grain cavity, and securing holder with wing nut provided. 6. Route moisture sensor cable to mating connector of distribution cable. 7. Install and route EMU power cable to battery. Connect fused wire to positive terminal and other wire to negative terminal of battery. PN: December 25 Rev C 23

24 Combine Installation JD 33//66/77; 2 Ag Leader Technology Final Inspection Installation is complete. Walk around combine to verify the following: All cable connections have been made. Excess cable has been tied out of way, to avoid interference. All tools have been removed from combine. All fasteners are tight. 2 December 25 Rev C

25 Ag Leader Technology Combine Installation JD 33//66/77; 2 Operational Checkout for Refer to the Display Items section in the Operation Section for instructions on how to display different items on the screen. Step-by-Step Procedure 1. Start engine. 2. Turn monitor power switch ON and verify that monitor turns on properly. A field and load should be displayed at top of screen. 3. Display Elevator Speed on screen. a. Verify elevator RPM stays at zero with separator and header OFF. b. Engage separator and verify monitor measures elevator RPM. It should be about RPM at full engine speed. NOTE: On some combine models, header must be engaged to receive elevator speed signal. If no elevator speed, engage header drive.. Display Ground Speed on screen. a. Ground speed should register zero with combine at rest. b. Move combine slowly. Monitor should register MPH value at low speeds (below 1 MPH). c. Engage separator with combine at rest and verify monitor reads. MPH. 5. Display Head Height on screen. a. Raise and lower header. Header height value should increase and decrease respectively. 6. Display Temp on screen and verify there is a temperature reading. The temperature may be off slightly because it has not been calibrated. Refer to Setup Section of Operator Manual to adjust monitor to your combine PN: December 25 Rev C 25

26 Combine Installation JD 33//66/77; 2 Ag Leader Technology Revision History Date Revision Initials Comments Jun 2 N/C MB Initial release Apr 22 A MB Added part number to footer and revisions to back page of document. Nov 22 B SAK Added support for. Dec 25 C SLH Corrected errors in parts list, updated and reformatted instructions. 26 December 25 Rev C

PFadvantage MF 6850/6855; Ideal 9080/9090

PFadvantage MF 6850/6855; Ideal 9080/9090 MF 6850/6855; Ideal 9080/9090 Note: Indented items indicate parts included in an Quantity by Model assembly listed above MF Ideal Part Name/Description Part Number 6850 6855 9080 9090 Instruction Kit MF

More information

PFadvantage Metalfor Araus 1360

PFadvantage Metalfor Araus 1360 Metalfor Araus 1360 Note: Indented items indicate parts included in an assembly listed above Part Name/Description Part Number Quantity Instruction Kit Metalfor Araus 2005300-14 1 Display Bracket 4000134

More information

Part Name/Description Part Number Quantity Instruction Kit Metalfor Flow Sensor

Part Name/Description Part Number Quantity Instruction Kit Metalfor Flow Sensor NOTE: Indented items indicate parts included in an assembly listed above Part Name/Description Part Number Quantity Instruction Kit Metalfor 4101091 1 Flow Sensor 4001356 1 Deflector plate 2000612-1 1

More information

Flow Sensor

Flow Sensor NOTE: Indented items indicate parts included in an assembly listed above Part Name/Description Part Number Quantity Instruction Kit Metalfor 4101091 1 Quick reference sheet 2002831-36 1 Installation instructions

More information

Rostselmash Torum 740

Rostselmash Torum 740 Note: Indented items indicate parts included in an assembly listed above Quantity by Model Part Name/Description Part Number 740 Combine Kit Torum 740 4100762 1 Threaded Arm Assembly 2000311-2 1 Header

More information

MF 9520 / 9540 / 9560, Challenger 540C / 560C

MF 9520 / 9540 / 9560, Challenger 540C / 560C Ag Leader Combine Installation Note: Indented items indicate parts included in an assembly listed above Part Name/Description Part Number 9520 Quantity by Model 9540 540C Parts Kit 2001312-69 1 1 1 Drill

More information

Lexion 570R/575R, 580R/585R, 590R/595R

Lexion 570R/575R, 580R/585R, 590R/595R Note: Indented items indicate parts included in an assembly listed above Quantity by Model 2006+ All Years Part Name/Description Part Number 570R 575R 580R 585R Instruction Kit Lexion 570/580/590 2005500-5

More information

Lower Adjuster Small Black Header Sensor Reversed

Lower Adjuster Small Black Header Sensor Reversed Parts List for Combine Quantity by Model Early Late Early Late Note: Indented items indicate parts included M M M M M M in an assembly listed above F F F F F F 7 7 8 8 8 8 5 6 5 5 6 6 Part Name/Description

More information

MF 9690, 9790, Challenger 660, 670

MF 9690, 9790, Challenger 660, 670 Ag Leader Technology Parts List Note: Indented items indicate parts included in an assembly listed above Quantity by Model Part Name/Description Part No. MF 9690 MF 9790 Challenger 660 Challenger 670 Instruction

More information

Installation Instructions for John Deere cotton picker models: 9986 & 2-row and All-row systems included.

Installation Instructions for John Deere cotton picker models: 9986 & 2-row and All-row systems included. Ag Leader Technology Cotton Picker Installation Installation Instructions for John Deere cotton picker models: 9986 & 9996 2-row and All-row systems included. IMPORTANT: Ensure the model numbers shown

More information

Instruction Kit Gleaner K2, K3, F2, F Flow Sensor K2-F

Instruction Kit Gleaner K2, K3, F2, F Flow Sensor K2-F Parts List for Combine NOTE: Indented items indicate parts included In an assembly listed above. Quantity by Model Part Name/Description Part No. K2 F2 Instruction Kit 2005300-1 1 1 Flow Sensor K2-F2 2000292

More information

Quantity by Model an assembly listed above Early Models Late Models. Instruction Kit JD 9x00/9x

Quantity by Model an assembly listed above Early Models Late Models. Instruction Kit JD 9x00/9x Note: Indented items indicate parts included in Quantity by Model an assembly listed above Early Models Late Models Part Name/Description Part Number 9400/ 9500/ 9600/ 9400 9500 9600 9410 9510 9610 Instruction

More information

Part Name/Description Part No

Part Name/Description Part No Parts List for Combine Note: Indented items indicate parts included in an assembly listed above Quantity by Model Part Name/Description Part No. 4425 4435 Instruction Kit JD 4425-4435 2005100-2 1 1 Moisture

More information

NOTE: Indented items indicate parts included in an assembly listed above. Early* Late** M3 M3 Part Name/Description Part No.

NOTE: Indented items indicate parts included in an assembly listed above. Early* Late** M3 M3 Part Name/Description Part No. Parts List Gleaner L2, L3, M2, M3 NOTE: Indented items indicate parts included in an Quantity by Model assembly listed above. Early* Late** M3 M3 Part Name/Description Part No. M2 L2 L3 L3 Instruction

More information

Flow Sensor Gleaner N5-R Flow Sensor Gleaner R40, R

Flow Sensor Gleaner N5-R Flow Sensor Gleaner R40, R Parts List for Combine Note: Indented items indicate parts included Quantity by Model in an assembly listed above Early Late N N N N N N R R R R R R R Part Name/Description Part No. 5 6 7 5 6 7 5 6 7 40

More information

Instructions for 2-row monitoring only

Instructions for 2-row monitoring only Installation Instructions for CaseIH cotton picker models: Instructions for 2-row monitoring only CAUTION: Ensure the model numbers shown above correspond to the machine model. If you receive the incorrect

More information

Instructions for 2-row monitoring only

Instructions for 2-row monitoring only Installation Instructions for CaseIH cotton picker models: Instructions for 2-row monitoring only Ensure the model numbers shown above correspond to the machine model. If you receive the incorrect installation

More information

2-row and All-row systems included.

2-row and All-row systems included. Ag Leader Technology Cotton Picker Installation Installation Instructions for John Deere cotton picker models: 2-row and All-row systems included. IMPORTANT: Ensure the model numbers shown above correspond

More information

Part Number Part Name/Description Instruction Kit JD 9x50/9x60/9x Flow Sensor

Part Number Part Name/Description Instruction Kit JD 9x50/9x60/9x Flow Sensor ATTENTION If installing combine kit on a 9x70 series combine with factory-installed yield/moisture sensors, please take note of the special instructions in the Operational Checkout section (page 41) for

More information

Flow Sensor Deflector Deflector

Flow Sensor Deflector Deflector Parts List of Combine Kit Note: Indented items indicate parts included Quantity by Model in an assembly listed above Early Models* 9 9 9 4 5 6 0 0 0 Part Name/Description Part No. 0 0 0 Instruction Kit

More information

Combine Kit Parts List New Holland Late TR89, Late TR99 (Yield Monitor Ready)

Combine Kit Parts List New Holland Late TR89, Late TR99 (Yield Monitor Ready) Combine Kit Parts List Note: Indented items indicate parts included Quantity by Model in an assembly listed above Late Late TR TR Part Name/Description Part No. 89 99 Instruction Kit NH YM Ready TR89,

More information

Ag Leader Technology. Parts List for Combine MF , 8780, White 9700

Ag Leader Technology. Parts List for Combine MF , 8780, White 9700 Parts List for Combine Quantity by Model Note: Indented items indicate parts included W in an assembly listed above 8 8 8 8 H 5 5 5 7 I 6 7 9 8 T Part Name/Description Part No. 0 0 0 0 E Instruction Kit

More information

Clutch Control. PN: November 2013 Rev E 1

Clutch Control. PN: November 2013 Rev E 1 NOTE: Indented items indicate parts included in an assembly listed above Part Name/Description Part Number Quantity Module Kit 4100533 1 Cable Installation Kit 2000901-1 1 Alcohol swab packet 2002811 2

More information

Ag Leader Technology. Combine Installation New Holland TC 57, 59. Monitor Installation

Ag Leader Technology. Combine Installation New Holland TC 57, 59. Monitor Installation Monitor Installation Figure 1. Monitor installed on right side cab window using window mount bracket. 1. If you are in very humid conditions where moisture may condense on the glass where you are mounting

More information

Installation Instructions for John Deere cotton stripper models:

Installation Instructions for John Deere cotton stripper models: Installation Instructions for John Deere cotton stripper models: 7445 7450 7455 IMPORTANT: Ensure the instructions you use for the installation correspond to the machine model. If you receive the incorrect

More information

Installation Instruction for John Deere cotton picker models:

Installation Instruction for John Deere cotton picker models: Cotton Picker Installation Installation Instruction for John Deere cotton picker models: 9900-9950 IMPORTANT: Ensure the instructions you use for the installation correspond to the machine model. If you

More information

Installation Instructions for John Deere cotton picker model:

Installation Instructions for John Deere cotton picker model: Cotton Picker Parts List Installation Instructions for John Deere cotton picker model: Two row and all row systems included. IMPORTANT: Ensure the instructions you use for the installation correspond to

More information

Installation Instructions for John Deere cotton picker models:

Installation Instructions for John Deere cotton picker models: Cotton Picker Installation Installation Instructions for John Deere cotton picker models: Two row and all row systems included. IMPORTANT: Ensure the instructions you use for the installation correspond

More information

Clutch Installation Case IH 1200 row unit

Clutch Installation Case IH 1200 row unit Ag Leader Technology SeedCommand NOTE: Indented items indicate parts included in an assembly listed above Part Name/Description Part Number Quantity 4 row clutch installation kit Case IH 1200 Model year

More information

RAM Rail Mount Kit RAM 201UD 5 Arm RAM 2461U Base RAM 235U Base, Double U-Bolt

RAM Rail Mount Kit RAM 201UD 5 Arm RAM 2461U Base RAM 235U Base, Double U-Bolt Note: Indented items indicate parts included in an assembly listed above. Part Name/Description Part Number Quantity Direct Command Kit 4100514 1 Installation Instructions 2005690 1 CAN Y-Splice 4000137

More information

Installation Guide CLAAS Lexion Combines with 9 inch Elevators

Installation Guide CLAAS Lexion Combines with 9 inch Elevators Installation Guide CLAAS Lexion Combines with 9 inch Elevators 955614_01 4/17 1 Table of Contents System Overview 3 Quick Start Guide 4 Flow Sensor Installation 5 Hydraulic Elevator Adjustment Kit Installation

More information

Installation Instructions Z-Gate Shifter

Installation Instructions Z-Gate Shifter Installation Instructions Z-Gate Shifter Part Number 80681 1998, 2001 by B&M Racing and Performance Products The B&M Z-Gate shifter can be used in vehicles equipped with most popular three speed automatic

More information

General Information. Notations and Conventions. Compatibility Check. Kit Description. Call-Outs. Part Lists Great Plains Manufacturing, Inc.

General Information. Notations and Conventions. Compatibility Check. Kit Description. Call-Outs. Part Lists Great Plains Manufacturing, Inc. Part Lists Great Plains Manufacturing, Inc. 1 Installation Instructions Loup Shaft Monitor Used with Drill models: Compatible with most 1995 and later, two- and three-box drills with 5 8 -inch square main

More information

Easy Cover. Installation Instructions. Attention Dealers: Please give this owners manual to the customer when the product is delivered.

Easy Cover. Installation Instructions. Attention Dealers: Please give this owners manual to the customer when the product is delivered. Serving the Truck & Trailer Industry Since 944 Easy Cover Attention Dealers: Please give this owners manual to the customer when the product is delivered. Call 00-3-94 www.aeroindustries.com Indianapolis,

More information

Z-Gate Universal Shifter

Z-Gate Universal Shifter Installation Instructions Z-Gate Universal Shifter Fits: GM, Ford, Lincoln and Chrysler Transmissions See Application Guide for Specific Applications Part #80681 Rev 06/01/2018 WORK SAFELY! For maximum

More information

ISOBUS Down Force Hydraulics Kinze

ISOBUS Down Force Hydraulics Kinze Important Notices Please carefully follow these step-by-step instructions. If you have questions, contact at 515-232-5363 x 1. Direction words (LEFT and RIGHT) are commonly used when describing an installation

More information

Part Name/Description Part No. PF3000 PF 3000 Pro U-Bracket Short Bracket PF3000 Pro

Part Name/Description Part No. PF3000 PF 3000 Pro U-Bracket Short Bracket PF3000 Pro Note: Indented items indicate parts included in an assembly listed above Part Name/Description Part No. PF3000 PF 3000 Pro U-Bracket Short 2000105-2 1 PFadvantage Bracket PF3000 Pro 2000773 1 Cable Kit

More information

RANGER 900 POWER STEERING KIT

RANGER 900 POWER STEERING KIT RANGER 900 POWER STEERING KIT P/N 2880083 APPLICATION MY14 AND NEWER RANGER XP 900 MODELS IMPORTANT It is strongly recommended that this kit be installed by an authorized Polaris dealer. NOTE Use of this

More information

Installation Instructions. QuickSilver Shifter. Fits: GM, Ford, Chrysler Transmissions See Application Guide for Specific Applications Part # 80683

Installation Instructions. QuickSilver Shifter. Fits: GM, Ford, Chrysler Transmissions See Application Guide for Specific Applications Part # 80683 Installation Instructions QuickSilver Shifter Fits: GM, Ford, Chrysler Transmissions See Application Guide for Specific Applications Part # 80683 WORK SAFELY! For maximum safety, perform this installation

More information

Ag Leader Technology InSight/Ag Leader Integra. OptRx OptRx Remote Sensor Kit

Ag Leader Technology InSight/Ag Leader Integra. OptRx OptRx Remote Sensor Kit : Indented items indicate parts included in an assembly listed above Part Name/Description Part Number Quantity Master Module Kit 4100804 1 Master Module 4001821 1 Cable - Master 4001904-10 1 Cable - CAN

More information

Installation Instructions. Attention Dealers: Please give this owners manual to the customer when the product is delivered.

Installation Instructions. Attention Dealers: Please give this owners manual to the customer when the product is delivered. Serving the Truck & Trailer Industry Since 1944 Attention Dealers: Please give this owners manual to the customer when the product is delivered. Call 800-535-9545 www.aeroindustries.com Indianapolis, IN

More information

Detroit Speed, Inc. Selecta-Speed Wiper Kit Corvette P/N:

Detroit Speed, Inc. Selecta-Speed Wiper Kit Corvette P/N: Detroit Speed, Inc. Selecta-Speed Wiper Kit 1968-72 Corvette P/N: 121621 A downpour of rain will no longer hinder your ability to clearly see the road. The Detroit Speed Selecta-Speed Wiper Kit provides

More information

Detroit Speed, Inc. Electric Headlight Door Kit Corvette P/N: &

Detroit Speed, Inc. Electric Headlight Door Kit Corvette P/N: & Detroit Speed, Inc. Electric Headlight Door Kit 1968-82 Corvette P/N: 122006 & 122007 The Detroit Speed Inc. Electric Headlight Door Kit replaces the stock vacuum actuated system on all 1968-82 Corvettes.

More information

Chrysler 727, 904, 518 Floor Mount Automatic Transmission Shifter Installation Instructions

Chrysler 727, 904, 518 Floor Mount Automatic Transmission Shifter Installation Instructions Chrysler 727, 904, 518 Mount Automatic Transmission Shifter Installation Instructions Building American Quality With A Lifetime Warranty! TOLL FREE 1-877-469-7440 tech@lokar.com www.lokar.com Release Button

More information

PRELIMINARY INSTALLATION INSTRUCTIONS. PARTS LIST Security System Kit (sold separately) P/N 08E51-EP4-101

PRELIMINARY INSTALLATION INSTRUCTIONS. PARTS LIST Security System Kit (sold separately) P/N 08E51-EP4-101 INSTALLATION INSTRUCTIONS Accessory Application Publications No. All 30510 (LX) 2006 PILOT Issue Date SEP 2005 PARTS LIST Security System Kit (sold separately) P/N 08E51-EP4-101 Security system control

More information

Installation Instructions Sport Shifter

Installation Instructions Sport Shifter The B&M Sport Shifter can be used in vehicles equipped with most popular three speed or four speed automatic transmissions. It is equipped with neutral safety and backup light switches, transmission brackets

More information

General Information. Veris Drive Option

General Information. Veris Drive Option No-Till and No-Till Precision Seeding System Used with: 3N-3010P and 3N-3020P 3N-3010 and 3N-3020! When you see this symbol, the subsequent instructions and warnings are serious - follow without exception.

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS [1] Description: Tow Hitch Wire Harness Kit [2] Application: Nissan Rogue Note: Tow Harness application is limited to specific vehicle option packages that include tow harness

More information

Installation instructions, accessories - Rear Seat Entertainment

Installation instructions, accessories - Rear Seat Entertainment XC90 Section Group Weight(Kg/Pounds) Year Month 3 39 2004 10 XC90 2003, XC90 2004, XC90 2005, XC90 2006, XC90 2007, XC90 2008 Replaces issue: 2003 12 J3904620 Page 1 of 18 Required tools A0000162 A0000163

More information

Illustrated Parts & Packing List & Instructions 815 Rice Lake Street, Owatonna, MN 55060

Illustrated Parts & Packing List & Instructions 815 Rice Lake Street, Owatonna, MN 55060 Illustrated Parts & Packing List & Instructions 815 Rice Lake Street, Owatonna, MN 55060 Great Plains Part #891-561C (Gandy Part #6245DS-GP) For Great Plains Turbo-Max 2400, 3000, 3500 & 4000 Models 45

More information

Technical Support (707)

Technical Support (707) Installation Instructions CONSOLE MEGASHIFTER Fits: 1982-1992 Camaro & Firebird w/automatic Transmission *except 1988-1992 Firebird Formula Model Catalog # 80692 WORK SAFELY! For maximum safety, perform

More information

LGT-306L / LB Club Car Precedent LED Light Bar Bumper Kit Installation Instructions

LGT-306L / LB Club Car Precedent LED Light Bar Bumper Kit Installation Instructions LGT-306L / LB Club Car Precedent LED Light Bar Bumper Kit Installation Instructions Caution: Please read through the instructions carefully. Before starting this project, remove the system s positive and

More information

GPS AutoSteer System Installation Manual

GPS AutoSteer System Installation Manual GPS AutoSteer System Installation Manual Supported Vehicles New Holland Combines CR 9040 CX 9040 CR 9050 CX 9050 CR 9060 CX 9060 CR 9070 CX 9070 CR 9080 CX 9080 IntelliSteer Ready PN: 602-0231-01-A LEGAL

More information

LGT-311L Bumper LED Light Kit EZ-Go RXV Installation Instructions

LGT-311L Bumper LED Light Kit EZ-Go RXV Installation Instructions LGT-311L Bumper LED Light Kit EZ-Go RXV Installation Instructions Caution: Please read through the instructions carefully. Before starting this project, remove the system s positive and negative connections

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Accessory HITCH Application 2012 CROSSTOUR Publications No. AII 46198 Issue Date JULY 2011 PARTS LIST Trailer Hitch Kit P/N 08L92-TP6-101 Upper spacer A (5 mm) (Some are not used.)

More information

GPS AutoSteer System Installation Manual

GPS AutoSteer System Installation Manual GPS AutoSteer System Installation Manual John Deere Track Supported Models 8295RT 8320RT 8345RT PN: 602-0255-01-A LEGAL DISCLAIMER Note: Read and follow ALL instructions in this manual carefully before

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Accessory S P/N 08V67-SJC-101 Application 2012 RIDGELINE Publications No. AII 12006 Issue Date NOV 2011 PARTS LIST Back-up sensor harness 3 Wire ties with small clips (2 Not used)

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Accessory HITCH Application 2009 CR-V Publications No. AII 40373 Issue Date AUG 2008 PARTS LIST Plain washer, 12 mm Trailer Hitch Kit P/N 08L92-SWA-100 Trailer hitch 6 Spring

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Accessory Application Publications No. AII 23086 SYSTEM CR-V Issue Date NOV 2001 PARTS LIST Security System P/N 08E51-EP4-100 Security System Attachment P/N 08E55-S9A-100 Security

More information

GPS AutoSteer System Installation Manual

GPS AutoSteer System Installation Manual GPS AutoSteer System Installation Manual Supported Vehicles Case IH Vehicles Case 2577 Combines Case 2588 Combines Accuguide Ready PN: 602-0233-01-A LEGAL DISCLAIMER Note: Read and follow ALL instructions

More information

SCION xd INTERIOR LIGHTING UPGRADE Preparation

SCION xd INTERIOR LIGHTING UPGRADE Preparation Preparation Part Number: PTS21-52085 Light Guide Kit Contents Item # Quantity Reqd. Description 1 1 Controller Board, 4 color programmed w/ Bracket 2 1 RGB, LED Engine wire harness 3 2 14mm Light Rod,

More information

JEEVES. JEEVES Installation Manual. Installation Manual The Easiest Do-It-Yourself Dumbwaiter on the Market

JEEVES. JEEVES Installation Manual. Installation Manual The Easiest Do-It-Yourself Dumbwaiter on the Market 1 888-323-8755 www.nwlifts.com JEEVES Installation Manual The Easiest Do-It-Yourself Dumbwaiter on the Market This manual will cover the installation procedure step-by-step. The installation of this dumbwaiter

More information

TCI FastGate Shifter Installation Instructions

TCI FastGate Shifter Installation Instructions 151 INDUSTRIAL DRIVE ASHLAND, MISSISSIPPI 38603 http://www.tciauto.com TELEPHONE: 662-224-8972 FAX LINE: 662-224-8255 E-MAIL: tech@tciauto.com TCI 616541 FastGate Shifter Installation Instructions The

More information

Installation Instructions Right Hand Drive Megashifter

Installation Instructions Right Hand Drive Megashifter Installation Instructions Right Hand Drive Megashifter Part Number 80685 1995, 2001, 2006, 2010 by B&M Racing & Performance Products The B&M Right Hand Drive Megashifter is designed specifically for vehicles

More information

RCA PLUG KIT P/N APPLICATION BEFORE YOU BEGIN KIT CONTENTS. Verify accessory fitment at Polaris.com.

RCA PLUG KIT P/N APPLICATION BEFORE YOU BEGIN KIT CONTENTS. Verify accessory fitment at Polaris.com. RCA PLUG KIT P/N 2883824 APPLICATION Verify accessory fitment at Polaris.com. BEFORE YOU BEGIN Read these instructions and check to be sure all parts and tools are accounted for. Please retain these installation

More information

Ford AOD-4R70W-AODE Cable Operated Shifter Installation Instructions

Ford AOD-4R70W-AODE Cable Operated Shifter Installation Instructions Ford AOD-4R70W-AODE Cable Operated Shifter Installation Instructions Building American Quality With A Lifetime Warranty! TOLL FREE 1-877-469-7440 tech@lokar.com www.lokar.com Ford AOD-4R70W-AODE Cable

More information

TOYOTA RAV4/HV INTERIOR LIGHT KIT Preparation

TOYOTA RAV4/HV INTERIOR LIGHT KIT Preparation Preparation Part Number: PT413-42130 Kit Contents Item # Quantity Reqd. Description 1 1 Wire Harness 2 3 Hardware Bag Contents Item # Quantity Reqd. Description 1 20 Cable Tie 2 2 Scotchlok 3 2 Foam Pad

More information

Hurst VMATIC3 INSTALLATION

Hurst VMATIC3 INSTALLATION FORM 159 8530 07/12 Hurst VMATIC3 3-Speed & 4-Speed Automatic Shifter Catalog #3838530 2012 by Hurst Performance The Hurst Vmatic3 shifter can be used in vehicles equipped with most popular three speed

More information

2016 HONDA 1000 Pioneer PN 3102 Turn signal / horn kit rev nc

2016 HONDA 1000 Pioneer PN 3102 Turn signal / horn kit rev nc 2016 Honda 1000 Pioneer STOP - THIS KIT IS DESIGNED SPECIFICALLY FOR 2016 HONDA 1000 PIONEER IF YOUR MACHINE IS NOT THIS MODEL DO NOT PROCEED. THIS KIT DOES NOT WORK ON THE PIONEER 500 nor 700 S. Contact

More information

Wolverine Turn Signal / Horn Kit 2102

Wolverine Turn Signal / Horn Kit 2102 All years Yamaha Wolverine STOP - THIS KIT IS DESIGNED SPECIFICALLY FOR ALL YEAR AND MODELS YAMAHA WOLVERINE. IF YOUR MACHINE IS NOT ONE OF THESE MODELS DO NOT PROCEED. Contact Ryco Motorsports or your

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Accessory Application Publications No. All 12035 SYSTEM 2012 RIDGELINE Issue Date NOV 2011 PARTS LIST Security System Attachment Kit: P/N 08E55-SJC-101 Flange bolt Unit bracket

More information

JODALE PERRY. Parts List & Mounting Instructions. Jacobsen HR9016 JDP BUILT FOR LIFE

JODALE PERRY. Parts List & Mounting Instructions. Jacobsen HR9016 JDP BUILT FOR LIFE JODALE PERRY Parts List & Mounting Instructions Jacobsen HR9016 JDP BUILT FOR LIFE Jacobsen HR9016 Mounting Instructions Standard Parts 1 - LH Rear Mounting Bracket 1 - RH Rear Mounting Bracket 1 - Front

More information

GPS AutoSteer System Installation Manual

GPS AutoSteer System Installation Manual GPS AutoSteer System Installation Manual Supported Vehicles MacDon M150 M200 PN: 602-0232-01-A LEGAL DISCLAIMER Note: Read and follow ALL instructions in this manual carefully before installing or operating

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Accessory S P/N 08V67-SJC-101 Application 2010 RIDGELINE Publications No. AII 42117 Issue Date AUG 2009 PARTS LIST Back-up sensor harness 3 Wire ties with small clip (2 Not used)

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Accessory S Application 2013 ACCORD 4-DOOR Publications No. AII 13026 Issue Date AUG 2012 PARTS LIST Aluminum tape Backup Sensors Attachment Kit P/N 08V67-T2A-100A Control unit

More information

INSTALLATION, MAINTENANCE, & SAFETY INSTRUCTIONS

INSTALLATION, MAINTENANCE, & SAFETY INSTRUCTIONS Tarpaulin Systems Flip -N- Go / Quick Mount Flip -N- Go System INSTALLATION, MAINTENANCE, & SAFETY INSTRUCTIONS (800) CRAMARO (800) 272-6276 Plants In: Delaware, Florida, Massachusetts, Nevada, Ohio Install

More information

Installation Manual. AutoSteer. Gleaner Combine. AutoGuide 2 Steer Ready. Supported Models A66 A76 R66 R76 S67 S77 PN: A

Installation Manual. AutoSteer. Gleaner Combine. AutoGuide 2 Steer Ready. Supported Models A66 A76 R66 R76 S67 S77 PN: A Installation Manual AutoSteer Gleaner Combine AutoGuide 2 Steer Ready Supported Models A66 A76 R66 R76 S67 S77 PN: 602-0312-01-A LEGAL DISCLAIMER Note: Read and follow ALL Instructions in this manual carefully

More information

Illustrated Parts & Packing List 815 Rice Lake Street, Owatonna, MN For a complete distributor & dealer list go to

Illustrated Parts & Packing List 815 Rice Lake Street, Owatonna, MN For a complete distributor & dealer list go to Illustrated Parts & Packing List 815 Rice Lake Street, Owatonna, MN 55060 For a complete distributor & dealer list go to www.gandy.net 6250BN36C Orbit-Air Applicator 50 Cu. Ft. Hopper w/ 26 (1-1/4 ) Openings,

More information

w w w. h d o n l i n e s h o p. d e CRUISE CONTROL KIT GENERAL INSTALLATION -J04064 REV Kit Number Models Additional Parts Required

w w w. h d o n l i n e s h o p. d e CRUISE CONTROL KIT GENERAL INSTALLATION -J04064 REV Kit Number Models Additional Parts Required -J006 REV. 006-08- CRUISE CONTROL KIT GENERAL Kit Number 7796-07 Models For the most up-to-date model fitment information, please see the product label or www.harley-davidson.com. Additional Parts Required.

More information

GPS AutoSteer System Installation Manual

GPS AutoSteer System Installation Manual GPS AutoSteer System Installation Manual Supported Vehicles Case IH Vehicles Case 5088 Combines Case 6088 Combines Case 7088 Combines Accuguide Ready PN: 602-0250-01-A LEGAL DISCLAIMER Note: Read and follow

More information

Light Truck MegaShifter

Light Truck MegaShifter Installation Instructions Light Truck MegaShifter The B&M Light Truck Megashifter shifter is designed to be used in most light trucks equipped with most popular three speed or four speed automatic transmissions.

More information

Assembly Instructions

Assembly Instructions Assembly Instructions Part Number Description Model Approx. Assembly Time 99994-0903 Windshield Wiper Kit Mule SX 1 Hour WARNING Improper installation of this accessory could result in an accident causing

More information

GPS AutoSteer System Installation Manual

GPS AutoSteer System Installation Manual GPS AutoSteer System Installation Manual Supported Vehicles Agco Gleaner Combines R65 R66 R75 R76 PN: 602-0288-01-A LEGAL DISCLAIMER Note: Read and follow ALL instructions in this manual carefully before

More information

INSTALLATION INSTRUCTIONS FUEL SURGE TANK KIT

INSTALLATION INSTRUCTIONS FUEL SURGE TANK KIT INSTALLATION INSTRUCTIONS FUEL SURGE TANK KIT BMW E46 3-Series, Excl Convertible Document: 19-0056 Support: info@radiumauto.com Relieve fuel pressure in vehicle before beginingthe installation. Disconnect

More information

INSTRUCTION, TRAIL CHARGER KIT P/N

INSTRUCTION, TRAIL CHARGER KIT P/N LIFT CORPORATION Sht. 1 of 8 DSG# M-05-03 Rev. A Date: 01/20/06 INSTRUCTION, KIT P/N 267370-01 ASSEMBLY P/N 267369-01 FUSE & FUSE HOLDER ASSEMBLY P/N 267376-01 COVER () P/N 267522-01 DC-DC P/N 906484-01

More information

Installation Instructions Megashifter

Installation Instructions Megashifter Installation Instructions Megashifter The B&M Megashifter shifter can be used in vehicles equipped with most popular three speed or four speed automatic transmissions. Your B&M Megashifter comes equipped

More information

INSTALLATION GUIDE P1000 PRO-CELL CURRENT FORD POLICE UTILITY INTERCEPTOR. pro-gard.com STRONG RELIABLE SECURE

INSTALLATION GUIDE P1000 PRO-CELL CURRENT FORD POLICE UTILITY INTERCEPTOR. pro-gard.com STRONG RELIABLE SECURE INSTALLATION GUIDE P1000 PRO-CELL 2013 - CURRENT FORD POLICE UTILITY INTERCEPTOR STRONG RELIABLE SECURE THESE COMPONENTS ARE REQUIRED TO INSTALL THE PRO-GARD PARTITION SYSTEM WB4711-01D WB4711-01P 4K47UINTPRO

More information

Section 13. Tail Rotor Drive. RotorWay International A600 TALON Construction Manual. Section 13. Page A

Section 13. Tail Rotor Drive. RotorWay International A600 TALON Construction Manual. Section 13. Page A RotorWay International Page A Tail Rotor Drive Procedures covered in this section: Install driveshafts and gearboxes; install drive belt and tensioner; fabricate and install tail rotor pitch actuator arms;

More information

TABLE OF CONTENTS INTRODUCTION 3. INSTALLATION PROCEDURES Air Conditioner Location 4. A/C Ducting Installation 5

TABLE OF CONTENTS INTRODUCTION 3. INSTALLATION PROCEDURES Air Conditioner Location 4. A/C Ducting Installation 5 585474 1 TABLE OF CONTENTS SECTION PAGE INTRODUCTION 3 INSTALLATION PROCEDURES Air Conditioner Location 4 Air Conditioner Mounting 4 A/C Ducting Installation 5 Power Kit Installation (Batteries). 5 Separator...

More information

R O A D S M I T H TRIKE CONVERSIONS BY THE TRIKE SHOP

R O A D S M I T H TRIKE CONVERSIONS BY THE TRIKE SHOP R O A D S M I T H TRIKE CONVERSIONS BY THE TRIKE SHOP Please thoroughly review the instructions before and during installation. Keep in mind that this product was designed to be installed by trained dealer

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Thank you for purchasing ROLTECTM Electric Hopper Conversion. Agri-Cover, Inc. proudly manufactured this hardware using superior quality materials and workmanship. With proper

More information

Illustrated Parts & Packing List & Instructions 815 Rice Lake Street, Owatonna, MN 55060

Illustrated Parts & Packing List & Instructions 815 Rice Lake Street, Owatonna, MN 55060 Illustrated Parts & Packing List & Instructions 815 Rice Lake Street, Owatonna, MN 55060 Great Plains Part #891-622C (Gandy Part #6245DS-TT) Great Plains Turbo-Till & Turbo-Chopper 2400/3000 Models 45

More information

Detroit Speed, Inc. Electric Headlight Door Kit Corvette P/N: &

Detroit Speed, Inc. Electric Headlight Door Kit Corvette P/N: & Detroit Speed, Inc. Electric Headlight Door Kit 1968-82 Corvette P/N: 122006 & 122007 The Detroit Speed Inc. Electric Headlight Door Kit replaces the stock vacuum actuated system on all 1968-82 Corvettes.

More information

80-96 Ford F150 / Bronco 4WD Class II 4"- 6" Suspension Lift Installation Instructions

80-96 Ford F150 / Bronco 4WD Class II 4- 6 Suspension Lift Installation Instructions www.skyjacker.com Required Tool List: 80-96 Ford F150 / Bronco 4WD Class II 4"- 6" Suspension Lift Installation Instructions Safety Glasses Metric / Standard Wrenches & Sockets Floor Jack Jack Stands Measuring

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Accessory BACKUP S Application 2012 ODYSSEY Publications No. AII 46724 Issue Date SEP 2011 PARTS LIST Backup Sensor Attachment Kit P/N 08V67-TK8-100A Right center sensor clip

More information

C15C C15C. Page 1 of 20

C15C C15C. Page 1 of 20 2 x Lid Front Hinge 1135 8 x M8 Bolt 8 x M8 Washer (3mm Thick) 4 x M6 Large washers 4 x M6 Spring washers 4 x M6 x 40mm Bolts 6 x M6 20mm Bolts 6 x M6 Washers 20 x Screws 2 x Lid mount gas strut bracket

More information

Combine Cover Manual

Combine Cover Manual Combine Cover Manual Installation Instructions Page 26 Operating Instructions Page 7 Warranty Page 7 Trouble Shooting Page 8 10 For Big Top Extension Model s: Case I.H. 8010, 8120 Please forward onto Customer

More information

INSTALLATION & OWNER S MANUAL

INSTALLATION & OWNER S MANUAL Rev. A, p. 1 of 13 INSTALLATION & OWNER S MANUAL Polaris Ranger (2009-) Straight UTV Steel Plow with Vehicle Mount Kit 6 Wide Snow Plow (p/n: 1POLSP) (fits the 500 H.O., 700 & 800 HD & XP) The contents

More information

<THESE INSTRUCTIONS MUST BE GIVEN TO THE END USER> B&W

<THESE INSTRUCTIONS MUST BE GIVEN TO THE END USER> B&W B&W Trailer Hitches 1216 Hawaii Rd / PO Box 186 Humboldt, KS 66748 Turnoverball Gooseneck Hitch Installation Instructions MODEL 1314 2013 2014 RAM 3500

More information

2005+ Roll Bar (Mm5RB-20.1 to -20.6) Recommended Center punch 1/8" pilot drill 1-3/4" Hole saw 2" Hole saw

2005+ Roll Bar (Mm5RB-20.1 to -20.6) Recommended Center punch 1/8 pilot drill 1-3/4 Hole saw 2 Hole saw 3430 Sacramento Dr., Unit D San Luis Obispo, CA 93401 Telephone: 805/544-8748 Fax: 805/544-8645 www.maximummotorsports.com 2005+ Roll Bar (Mm5RB-20.1 to -20.6) Recommended Center punch 1/8" pilot drill

More information