Model Turbo-Bar General Specification

Transcription

1 Model General Specification TMP-600/60S TMP-700 TMP-800/80S TMP-910/960 Features! Fluid types: liquid, gas or steam! Pipe sizes: 3 to 80 in. (80 to 000 mm)! Rugged construction! Interchangeable rotors for a wide variety of applications! Process pressure up to 000 psig (34 barg)! Process temperatures up to 70 F (400 C)! Industry standard frequency and/or 4 to 0 ma output signals! Optional integral pressure and/or temperature measurement! Optional bidirectional flow rate measurement! Negligible head loss! EZ-Logic menu-driven user interface (microprocessor-based)! Linearization with EZ-Logic for enhanced accuracy at low velocities! Local programming via EZ-Logic keypad or magnet wand through explosion-proof enclosure! Compatible with HART protocol EMCO's Insertion Turbine fl owmeters measure flow rates for a variety of fl uids and pipe sizes. Unlike an inline flowmeter, which replaces a section of pipe, an insertion meter is tapped into the flow line and can be mounted virtually anywhere. EMCO's insertion fl owmeters have three main components: the retractor, the rotor, and the electronics. The retractor positions the rotor within the pipe and houses a pick-up assembly, which detects the rotation of the turbine rotor. The electronics converts the rotational frequency, which is proportional to the velocity of the fl uid, to industry standard electrical output signals. Most fl owmeters can be installed on an isolation valve, which permits installation and removal without process shutdown. Integral pressure and/or temperature measurement may be combined with the Turbo- Bar and fl ow processor to provide mass or energy flow measurement from a single pipe tap Fax sales@emcoflow.com

2 Application Guide Model Liquid Gas Steam Hot Tap Temperature Range Maximum Pressure 1 Seal Type Line Sizes F C psi bar in. mm 600 yes yes no yes Ð40 to 400 Ð40 to Viton ª 3 to to S no no yes yes Ð6 to 400 Ð4 to E/P 3 3 to to yes yes yes no Ð00 to 600 Ð19 to Swagelok ª 3 to to yes yes no yes Ð40 to 400 Ð40 to Viton ª 3 to to S no no yes yes Ð6 to 400 Ð4 to E/P 3 3 to to yes yes yes yes Ð00 to 400 Ð19 to 04 flange rating Teflon ª 3 to to yes yes yes yes Ð00 to 70 Ð19 to 400 flange rating Grafoil ª 3 to to Maximum pressure at maximum temperature with appropriate connection.. In some cases, especially in large pipe sizes, a one or two foot stem extension may be required (See dimensional outlines). 3. Ethylene-Propylene elastomer. 4. Rating listed is for NPT connection. For flange connections, use ANSI flange rating.. The TMP-700 is a fi xed insertion meter; it cannot be removed or installed under pressure. Operating Specifications Measurable Velocity Limits See Rotor Selection Guide, p., for linear and measurable ranges of available rotors. Continuous operation above the maximum velocity will shorten the life of the rotor and is not recommended. Bidirectional Flow Includes two electromagnetic pick-up assemblies, one for sensing forward fl ow and one for sensing reverse fl ow. Specify either the PA (frequency) or PQ (current) preamplifi er for bidirectional applications. The PA provides a relay output indicating fl ow direction. The PQ provides two 4 to 0 ma signals one for each direction of fl ow. Note: EZ-Logic electronics not available for bidirectional fl ow measurement. Process Viscosity Maximum centipoise Ambient Temperature Limit EZ-Logic Electronics... 3 to 140 F (0 to 60 C) All Other Electronics... 0 to 140 F ( 40 to 60 C) Ambient Humidity Limit 0 to 100% relative humidity non-condensing Power Requirements EZ-Logic Electronics 18 to 40 VDC (with totalizer on), 4 VDC nominal 1 to 40 VDC (with totalizer off), 4 VDC nominal All Other Electronics 1 to 40 VDC, 4 V dc nominal Output Signals EZ-Logic Electronics (LOC-TOT Option) Analog 4 to 0 ma, -wire system, digitally adjusted span Frequency 3-wire system, 1 to 10,000 Hz square wave, 0% duty cycle. Low Level: 0 to 1 volts High Level: power supply voltage-load Pulse 3-wire system. Output can be scaled so that 1 pulse indicates a specifi c quantity of fl uid passing through the pipe. Hart Communications Protocol Display -line by 8-character LCD digital display alternately show fl ow rate and totalized fl ow in user-selectable engineering units. PA1 Electronics Frequency, 3-wire; 10 Vp p square wave PA Electronics Bidirectional frequency, 3-wire; 10 Vp p square wave with internal form-c relay (10 VA) for fl ow direction PAQ Electronics Current, -wire; 4 to 0 ma, 1 second time constant. PQ Electronics Bidirectional current; two 4 to 0 ma outputs, one for each fl ow direction.

3 Performance Specifications Accuracy (linear ranges) L1, G1 G rotors... ± 1.0% of reading G6 rotor... ± 3.0% of reading Repeatability (linear range) ± 0.% of reading Rotor Velocity Calibration Each rotor is factory calibrated in either water or air. Calibration is traceable to NIST. Accuracy of the Calibration Standard (linear range) Water...± 0.% of reading Air...± 0.8% of reading Physical Specifications Materials Rotor... Blades: 17 4 PH, ten blade, precision machined Housing: 316 stainless steel Pivots: tungsten carbide Rotor Bearing Type: Liquid... CSJ stellite jewel Gas or Steam... DEV tungsten carbide Wetted Parts L stainless steel stem and housing (bronze & carbon steel housing TMP-600/60S) External Parts... Aluminum, 316 stainless steel,carbon steel (bronze & carbon steel on TMP-600/60S, TMP- 910/960) Electrical Enclosure Aluminum. Approved for NEMA 4X for watertight and dust tight requirements. Electrical Connection Junction box with terminal block for external wiring. 3/4" female NPT connection for conduit. Sensor Electromagnetic pick up, 10 mvp p minimum, 330 Ω nominal resistance. Retractor Type TMP-600/60S...Screw thread, rising stem TMP Not retractable TMP-800/80S...Manual rising stem TMP-910/960...Acme thread, non-rising stem Extended Length Stem (Optional) Longer stems are available for large pipe sizes or when the mounting dimensions exceed the insertion capability. Extended stems are not available for the TMP-600/60S. Note: Use of the two foot extension is limited to gas applications only. Process Connection TMP-600/60S..." NPT TMP " NPT or " 10#, 300#, 600# or 900# ANSI raised face fl ange TMP-800/80S..." NPT or " 10# ANSI raised face fl ange TMP-910/960 " 10#, 300#, 600#, 900#, or 100# ANSI raised face fl ange Isolation Valve (TMP-600/60S only) " full port bronze gate valve, 1 psi (8.6 bar) maximum. For TMP-800/80S and TMP-910/960, see Accessories. Pressure Tap and Bleed Valve Standard 1/4" NPT pipe nipple with 1/4" stainless steel bleed valve. Provides connections for mounting optional pressure transmitter (Model PT). Model PT Pressure Transmitter (Optional) A pressure transmitter can be mounted using the 1/4" NPT connection on the bleed valve supplied with the meter, eliminating the need for a separate pressure tap. A 4 to 0 ma output, scaled to the desired pressure range, is provided. All pressure transmitters include a siphon tube, bleed valve, plug, nipple, and tee. A pressure transmitter is not available with 110/0 VAC power. See the PT General Specifi cations for complete details. Temperature Sensor (RTD Option) A 1000 Ω, platinum RTD can be mounted inside the stem of the fl owmeter probe, eliminating the need for a separate temperature tap. Temperature Transmitter (TXX Option) Includes the RTD option with an additional 4 to 0 ma output, scaled to the desired temperature range. A temperature transmitter is not available with 110/0 VAC power and is not CE approved. Remote Mount Electronics (RMT Option) 30 ft (9.1 m) signal cable and U-bolts are provided with remote mount electronics. Cable must be run in conduit (conduit not supplied). Conduit connection is 3/4" NPT. Note: Remote mount electronics is only available with EZ-Logic electronics (LOC-TOT Option). FM Approval (FM Option) Certifi ed by FM for Class I, Division, Groups A, B, C and D; Classes II, III, Division, Groups F and G NEMA 4X locations. Note: FM not available when used with 4 to 0 ma temperature transmitter or pressure transmitter or special scaled. European CE Mark European CE mark when used with EZ-Logic electronics and without a 4 to 0 ma temperature output. 3

4 Accessories Gate Valve (Model GV) (For use with TMP-800/80S and TMP-910/960 only) Installation with a " double fl anged, raised-face, full port gate valve enables the fl ow sensor to be inserted and removed from the pipe under full fl ow conditions. Both the valve and pipe tap must have a minimum 1.87 in. (48 mm) internal diameter clearance. Flow Rectifier (Model EFR) A fl ow rectifi er (EFR) is recommended when there is insuffi cient straight pipe run or fl ow disturbance. When using an EFR, the straight pipe run can be a combination of pipe diameters upstream and pipe diameters downstream, instead of the standard 10 and. Flow Processors (Models FP-93 and FP-100) A microprocessor-based fl ow processor can be used to signifi cantly increase the accuracy and functionality of any fl owmetering application. See the FP-93 or FP-100 General Specifi cations for complete details. Straight Run Piping Requirements Upstream Downstream One 90 elbow before the meter 10 D D Two 90 elbows before the meter 1 D D D is equal to the internal diameter of the pipe. If there is not sufficient straight run of pipe, a fl ow rectifier can be used to reduce the above lengths. Consult your local representative or the factory for your application. Two 90 elbows out of plane before the meter 30 D D Reduction before the meter 10 D D Regulator or valve partially closed before the meter 30 D D Other Installation Considerations Tap Size 1.87 in. (47.6 mm) minimum diameter. Mounting Position probes may be installed in vertical, horizontal, or angled pipe sections. The meter is attached perpendicular to the axis of the pipe and should not be mounted upsidedown (with its top section hanging below the pipe mount). For liquid service, the fl uid must completely fi ll the pipe. Site Selection The fl ow measurement location should be selected to minimize turbulence and swirl. The extent of these fl ow disturbances depends upon the piping confi guration. Valves, elbows, pumps, and other piping components may add disturbances to the fl ow. Hot Tap Comapatibility The TMP-600/60S is hot tap compatible, which means that the sensor can be installed and removed under full fl ow conditions. The TMP-800/80S with fl anged connection and TMP-910/960 are hot tap compatible when installed with a " double fl anged, full port ball or gate valve that adheres to the dimensions of the gate valve on page 7. 4

5 Rotor Selection Guide G6 (1" rotor) G1 thru G, L1 (1." rotor) Rotor Liquid Minimum and Maximum Velocity Rates Flow Units All Sizes 3Ð" (80Ð1mm) 6" (10mm) 8+" (00+mm) V max V lin V min V lin V min V lin V min L1 ft/s m/s Gas or Steam Minimum and Maximum Velocity Rates (ft/s) Rotor All 3 in. 6 in. 8+ in. Sizes Selection of the turbine rotor model depends upon the fl uid type and operating velocity range of the fl uid. For all liquids, the model L1 rotor, with a maximum velocity of 30 ft/s (9 m/s), must be used. For gases and steam, six different rotors are available with maximum velocities ranging from to 17 ft/s (17 to 3 m/s). See Table for maximum velocity limits (V ) for all rotors. Note: Rotors have moving parts that require periodic maintenance. The turbine rotor typically will respond linearly over the velocity range from V lin to V max within ± 1.0% (3.0% for G6 rotor). This is defi ned as the linear range of the rotor. The minimum measurable velocity (V min ) can be considered the application minimum. Velocities from V min to V lin are tmeasurable and repeatable, but less accurate. When determining the fluid velocity limits for a given rotor, the following equations can be used to compute fluid velocity Average Fluid Velocity Fluid English Metric Liquid Q Q D D Gas 3.06 Q Q g g 33.7 D D Steam 0.01 M 33.7 M Where: V = average fluid velocity D = pipe inside diameter Q 1 = liquid volumetric flow Q g = gas actual volumetric flow M = mass flow rate = fluid density ft/s in. ft 3 /min lb/h lb/ft 3 m/s mm m 3 /h m 3 /h kg/h kg/m 3 G1 40 pitch G 30 pitch G3 0 pitch G4 1 pitch G 10 pitch G6 1 pitch V max Vlin V min Vlin Vmin Vlin Vmin 3.19/ ρ 1.94/ ρ.00/ ρ 1.3/ ρ 1.0/ ρ 1.00/ ρ / ρ.6/ ρ.7/ ρ 1.63/ ρ 1.90/ ρ 1.31/ ρ 8 4./ ρ.4/ ρ./ ρ 1.9/ ρ.18/ ρ 1.40/ ρ 11.84/ ρ 3.8/ ρ 3.78/ ρ.84/ ρ 3.00/ ρ.19/ ρ / ρ 4.7/ ρ 4.78/ ρ 3.47/ ρ 3.4/ ρ.81/ ρ / ρ N/A.3/ ρ N/A.00/ ρ N/A Gas or Steam Minimum and Maximum Velocity Rates (m/s) Rotor G1 40 pitch G 30 pitch G3 0 pitch G4 1 pitch G 10 pitch G6 1 pitch All Sizes 80-1 mm 10 mm 00 mm V max V lin V min V lin V min V lin V min / ρ.37/ ρ.44/ ρ 1.0/ ρ 1.83/ ρ 1./ ρ / ρ.76/ ρ.77/ ρ.00/ ρ.3/ ρ 1.60/ ρ 6.1/ ρ.9/ ρ 3.07/ ρ.38/ ρ.67/ ρ 1.71/ ρ 3 7.1/ ρ 4.70/ ρ 4.61/ ρ 3.46/ ρ 3.66/ ρ.67/ ρ / ρ.7/ ρ.83/ ρ 4.3/ ρ 4.3/ ρ 3.43/ ρ / ρ N/A 6.7/ ρ N/A 6.10/ ρ N/A 1. The G6, 1" bidirectional rotor, is not available.. All values in the above table are approximate and depend on the density of the fl uid. Accuracy in both the linear, and nonlinear, ranges may be improved by using the advanced curve fi tting techniques present in one of EMCO's fl ow processors or the EZ-Logic electronics. Consult EMCO if your application falls outside the above limits. V max = maximum velocity of fl uid [ft/s (m/s)] V lin = minimum velocity of fl uid at which rotor response is linear [ft/s (m/s)] V min = minimum measurable velocity of fl uid [ft/s (m/s)] ρ = density of fl uid [lb/ft 3 (kg/m 3 )] N/A = not applicable For EMCO Flowmeter Sizing Download emcosizing program "emcosize" at

6 EMCO FLOW Dimensions and Weights TMP-600/60S All dimensions are in 1 (30) inches (millimeters). Recommended Service Clearance TMP (30) Recommended Service Clearance All dimensions are in inches (millimeters). Dimension Tables Model Connection C 600/ 60S " NPT in. 4. min 18 max mm 114 min 47 max 700 " NPT 3 min 10 max 76 min 4 max 40 (1016) " Isolation Valve Pressure Transmitter (Optional) Insertion Depth Scale 1. (318) C 33* (838*) 14.* (368*) Swagelok Fitting Orientation Lever Pressure Transmitter (Optional) " ANSI 10, 300, or 600# Flange 800/ 80S " 10# " 300# " 600# " 900# " NPT & " 10# 3 min 11. max 3 min 76 min 9 max 76 min 11. max 8 max 3 min 11 max 3 min 10.7 max min 0 max 76 min 79 max 76 min 73 max 1 min 08 max " NPT C C Model Stem Length B A in. mm in. mm 1 (30) 910/ 960 Standard 1.min 38min 0max 08max * Add 1 in. (30 mm) for each additional foot of retractor length. * Add 1 in. (30 mm) for each additional foot of retractor length. TMP-800/80S 44* (1118*) All dimensions are in inches (millimeters). 1 (30) Recommended Service Clearance 6* (660*) Lock Rings Orientation Lever Pressure Transmitter (Optional) " ANSI 10, 300, or 600# Flange " NPT C * Add 1 in. (30 mm) for each additional foot of retractor length. C TMP-910/960 All dimensions are in inches (millimeters). 1 (30) Recommended Service Clearance Insertion Depth Scale Packing Gland Orientation Lever Pressure Transmitter (Optional) * Add 1 in. (30 mm) for each additional foot of retractor length. A B Weight Model Connection Weight 60S lb " NPT 8 kg " NPT 9* 4.1* 800/ 80S 960 " 10# 1*.4* " 300# 14* 6.3* " 600# 16* 7.* " 900# 0* 9.1* " NPT 11*.0* " 10# 17* 7.7* " 10# 30** 13.6** " 300# 3** 1.8** " 600# 40** 18.1** " 900# 47** 1.3** * Add. lb (1. kg) for each additional foot of retractor length. ** Add lb (.3 kg) for each additional foot of retractor length. 6

7 Dimensions and Weights All dimensions are in inches (millimeters). Integral Electronics Pipe Mount Remote Electronics Gate Valve Flow Transmitter Condulet Standard " pipe ( 0 pipe) 1.87" Min. Clearance Z Field Wiring Condulet (3/4" NPT Conduit) Temperature Preamplifier - TEM (Optional). (133) 6. (16.1) 8. (1.9) (17) X Y Remote Electronics Configuration Pipe Mount Remote Electronics Gate valve is intended for use with the TMP-800/80S and TMP-910/960 only. Pipe Mount Wall Mount. (133) Flow Transmitter Condulet Field Wiring Condulet (3/4" NPT Conduit) Temperature Preamplifier TEM (Optional) (17) (17) 8. (1.9) 0.4 (10.) 8. (1.9) Dia (7.14) 4. (106.7) (17) 7.70 (19.6) 0.4 (10.) Type X Y Z in. mm in. mm in. mm 10# # # Type Weight lb kg " 10# " 300# " 600# For fl ange kit, add 14 pounds (6.4 kilograms) to weight. 7

8 Wiring Diagrams PA1 Electronics Frequency, 3-wire; 10 Vp p square wave. V s = 1 40 VDC. See graph below for permissible R load values. PAQ Electronics Current, -wire; 4 to 0 ma, 1 second time constant. Vs = 1 40 VDC. See graph below for permissible R load Shield PRESS (-) TEMP (-) SIGNAL (-)PA1 or PAQ DC COMMON +1 TO +40 VDC ma Press (Optional) 4-0 ma Temp (Optional) Flow Signal (Frequency) RP RT I I 0-00 HZ Vs Shield PRESS (-) TEMP (-) SIGNAL (-)PA1 or PAQ DC COMMON +1 TO +40 VDC ma Press (Optional) RP 4-0 ma Temp (Optional) RT 4-0 ma Flow Signal RF I I I + Vs EMCO + EMCO Maximum Load Resistance (Ω) LOAD = 0 (Vs 1) 1 4 Permissible Load Resistance Range Power Supply Voltage (VDC) 60 Maximum Load Resistance (Ω) LOAD = 0 (Vs 1) 1 4 Permissible Load Resistance Range Power Supply Voltage (VDC) 60 EZ-Logic Electronics: Analog Output Scalable 4 to 0 ma output, -wire principle. Load resistor may be installed on supply or return line. V s = VDC. See graph below for permissible R load values. EZ-Logic Electronics: Pulse Output 3 wire system. Output can be scaled so that 1 pulse indicates a specifi c quantity of fl uid passing through the pipe. V s = VDC. MADE IN USA R load + V s V pulse V s MADE IN USA + P + P Maximum Load Resistance (Ω) LOAD = 0 (Vs 18) With Totalizer Turned "Off" With Totalizer Turned "On" Permissible Load Resistance Range Power Supply Voltage (V dc) 40 8

9 11.4 Pressure and Temperature Transmitter Wiring Remove the fi eld wiring condulet cap to access the fi eld wiring terminal block for power and signal wiring. Flow, pressure, and temperature output wiring connects to the terminal block. Refer to the previous section on 4 VDC power and signal wiring for appropriate load resistance and power supply values. Pressure and temperature transmitters are scaled to the appropriate ranges at the factory. Note: Maximum voltage with optional pressure transmitter is 30 VDC and 110/0 VAC power supply is not available with pressure and/or temperature transmitters. Wiring with analog output: where: V s = VDC R p = Pressure measuring resistance R T = Temperature measuring resistance R F = Flow rate measuring resistance Remote Mount Wiring Diagram (Only available with EZ-Logic Electronics) Output wiring from remote electronics is identical to output wiring from integral electronics. Wiring from the remote electronics condulet to the electrical junction box must be performed in the fi eld. Connect the remote cable to the terminal block in the junction box as shown. If nonconductive conduit is used, attach a ground strap from the ground screw on the remote electronics condulet. If the remote cable is cut to a shorter length, insulate shield with tape at electrical junction box. Note: If remote mounting is required with a pressure and/or temperature transmitter, two power supplies are required for operation: one for the remote flow transmitter and one for the pressure and/or temperature transmitter. BLK WHT Remote Mount Cable DR GR Grounding Screw Grounding Strap Earth Ground (Not Pipe) Rigid Conduit Maximum Cable Length is 0 ft (17 m) Remote Cable Wiring Sensor Input COIL INPUT Must add a water tight or explosion proof seal 9

10 EZ-Logic Interface Map Customer Name FLUID: Exit No SavChng? Yes To Move Through Map SEC 1. Use up/down and right arrows as shown in map. While in display mode hold down right arrow key for sec. to go to programming mode 3. While in column headings press ENTER key to go to display mode. You will be prompted by "Exit?" and then "Sav Chg?". Display Password x1 gal 10% To alter data 1. To alter data press ENTER key within selected block. Use up/down arrows to alter value 3. Use right arrow to move cursor position 4. To store data press ENTER Error code 4 Output Fluid Sensor Reset Service Password HART Display C menu C menu C Menu C Menu D Menu D menu P menu P menu P Basic menu FlowRate Show Total Hide BarGraph Show Err Code Show TotReset Yes Dsply TC 0 Sec Scan On ScanTime 0 Sec Flow Res 8 digits Hart On Set Pass 1000 Sub Freq 0000 Hz 4-0 Out 0.000% Freq Out Hz TurbFreq 0 Hz 4mA Cnt mA Cnt 710 Version 1.00 Error code 4 Obs Fac Prof Fac Totalizer Reset Factory Default Density Ref Den Viscos cp 4-0 ma On 4-0 TC 0 sec Zero TM 0 sec EMCO FP? No Freq out Scl freq Flw unit Tot unit x1 gal Max flow freq # Hz vel # f/s freq # Hz vel # f/s Rotor SMALL<= WO# Tag # Pipe ID 1 in freq # Hz vel # f/s freq #.0000Hz vel #.000f/s freq # Hz vel # f/s freq # Hz vel # f/s freq #.0000Hz vel #.000f/s freq # Hz vel # f/s Work Order # Direct Off Transit Per puls Puls unt ft 3 Pulse + Per puls Puls unt ft 3 Puls wth 0 msec Pulse Per puls Puls unt ft 3 Puls wth 0 msec Turbfreq Freq TC 0 Sec Scl freq Freq max 10 khz Freq TC 0 Sec 10

11 Model and Suffix Codes Category Description Suffix Codes Model Connection Rotor Electronics Pressure Transmitter Temperature Sensor or Transmitter Extended Stem Pick-up Coil Wires Liquid or gas service, 400 F (04 C) TMP Steam service, 400 F (04 C) TMP-60S Liquid, gas, or steam service, 600 F (316 C) TMP Liquid or gas service, 400 F (04 C) TMP Steam service, 400 F (04 C) TMP-80S Liquid, gas, or steam service, 400 F (04 C) TMP Liquid, gas, or steam service, 70 F (400 C) TMP ", male NPT (model 700, 800, 80S)... NPT ", 10# flange (model 700, 800, 80S, 910, 960)... F ", 300# flange (model 700, 910, 960)... F ", 600# flange (model 700, 910, 960)... F ", 900# flange (model 700, 910, 960)... F ", 100# flange (model 910, 960)... F Thread-o-let, xx = inches (models 600, 60S) includes " isolation valve... VXX Liquid, 30 ft/s maximum (9 m/s) (40 pitch) L Gas or steam, ft/s (17 m/s) maximum (40 pitch) G Gas or steam, 70 ft/s (1 m/s) maximum (30 pitch) G Gas or steam, 8 ft/s (6 m/s) maximum (0 pitch) G Gas or steam, 11 ft/s (3 m/s) maximum (1 pitch) G Gas or steam, 14 ft/s (44 m/s) maximum (10 pitch) G Gas or steam, 17 ft/s (3 m/s) maximum ( pitch) G For bidirectional rotor XXB V p-p frequency output PA Bidirectional, 10 V p-p frequency output (relay) PA to 0 ma current output PAQ Bidirectional, two 4 to 0 ma current outputs PQ EZ-Logic with local rate and total LOC-TOT Remote, only available with LOC-TOT option RMT FM Approval FM No pressure transmitter XX PT for pressure range 0Ð0 psig (0Ð3.44 barg) Ð100 psig (0Ð6.89 barg) (models 600/60S, 700, 910/960) Ð10 psig (0Ð10.34 barg) (models 600/60S, 700, 910/960) Ð00 psig (0Ð13.79 barg) (models 600/60S, 700, 910/960) Ð0 psig (0Ð17.4 barg) (models 700, 910/960) Ð00 psig (0Ð34.47 barg) (models 700, 910/960) Ð1000 psig (0Ð68.9 barg) (models 700, 910/960) Special scaling requests PXX No temperature transmitter XXX RTD only RTD Temperature sensor with preamplifier scaled from 3 to 68 F T to 0 F T Ð40 to 10 F T to 400 F T to 800 F (models 700, 960) T Ð17.7 to 11.1 C T Ð40 to 6 C T to 04 C T to 60 C (models 700, 910/960) T Special scaling requests 6, TXX None (standard length) XX... 1' extension (not available for models 600/60S) E1... ' extension (gas/steam applications only) (not available for models 600/60S) E... TMP-700 Only: Teflon, Ð00 to 400 F (Ð19 to 04 C) T TMP-700 Only: Fiberglass, 10 to 600 F (6 to 316 C) F 1. The G6 is the only available 1" shrouded rotor. Not available for use with bidirectional meters.. Not available with European CE Mark. 3. Unidirectional only. Unit has 4 to 0 ma and frequency output. 4. Remote mount electronics are required for high process temperatures. The standard remote mount option comes with 30 feet (9.1 meters) of cable.. Certified by FM for Class I, Div., Groups A, B, C, & D; Class II,III, Div., Groups F & G; NEMA 4X. FM approval with only LOC-TOT and RMT electronics options. If FM is required, use RTD option only for temperature selection psia and special sealing pressure transmitter not available with FM. 6. Special transmitter scaling is available. Please note scaling range below model code with ordering. If no special scaling is indicated, transmitter will be scaled per model code. EXAMPLE: TMP-910-F900-G3-PA1-000-T1-E1 (for bidirectional meters): TMP-910-F900-G3B-PA-000-T1-E1 ORDERING INSTRUCTIONS Please specify the following information with your order: Fluid type or composition Maximum, minimum, & normal operating fl ow rate Maximum, minimum, & normal operating temperatures Maximum, minimum, & normal operating pressures Specifi c weight & viscosity at normal operating conditions 11

12 Providing innovative flowmeter products and services for over three decades... (EMCO) is a long established manufacturer of precision fl owmeters for liquid, gas, and steam applications for commerce and industry. Manufactured under an ISO 9001 certifi ed quality system, which includes extensive fl ow calibration capability, engineering, applications, and service, underpining a world-wide sales and service organization totally focused on providing the best fl owmeters and customer service in the industry. 4 Manufacturing is housed in a modern plant located in Longmont, Colorado 4 Modern clean-room, mechanized assembly equipment, and computer based testing ensure the highest quality product 4 Trained professional flow specialists and technicians offer timely customer assistance 4 Factory trained and certified field technicians provide product support services V-Bar Insertion Vortex Vortex PhD Inline Vortex Insertion Turbine MAGFLO Electromagnetic PDH Helix PDP Piston Sono-Trak Rev.H Specifications subject to change without notice 600 Diagonal Hwy. Longmont, CO 8001 (303) Fax (303) sales@emcofl ow.com