TORi INSTRUCTION SHEET. Minimalist Linear Fixture T5/T5HO. CSS - Cable Suspended. 1. Cut cables to desired length - take care not to fray cable ends.
|
|
- Sherman McCormick
- 6 years ago
- Views:
Transcription
1 TORi Minimalist Linear CSS - Cable Suspended J-BOX (BY OTHERS) 3-O or 4-0 MUD RING (BY OTHERS) J-BOX BRACKET BAR 1/4-20 STUD 8-32 BRACKET BAR SCREWS (BY OTHERS) CANOPY STND - 5 CANOPY 1. Cut cables to desired length - take care not to fray cable ends. 2. Insert cables into gripper ends and adjust to desired length. 3. Insert power cable through canopy and secure with provided strain relief. 4. Complete wire make-up. 5. Install canopy with cable gripper parts. CANOPY MOUNTING GRIPPER AIRCRAFT CABLE NC - NO CANOPY TYPICAL TORI CABLE SUSPENDED COMPONENTS CABLE LENGTH
2 TORi Minimalist Linear CSS - Cable Suspended Cable Mount Center Dimensions Nominal Wattage Cable Mounting Centers 3' 21w 39w 35-5/8" 4' 28w 54w 47-7/16" 5' 35w 80w 59-1/4" Overall T5 T5HO 2' 14w 24w 23-13/16" 24-13/16" 36-5/8" 48-7/16" 60-1/4" TORi-RB S Nominal Wattage Cable Mounting Centers T5 T5HO 2' 14w 24w 24-1/16" 3' 21w 39w 35-5/8" 4' 28w 54w 48-11/16" 5' 35w 80w 60-1/2" Overall 24-5/16" 35-7/8" 48-15/16" 60-3/4" TORi-IB Continuous Run Information 1/16 AIRCRAFT CABLE POWER CORD T5 OR T5HO LAMP 5-3/4 SOCKET COVER STARTER FIXTURE MIDDLE FIXTURE MIDDLE FIXTURE END FIXTURE
3 TORi Minimalist Linear ARM - Arm Mount Remote Ballast 1. Install J-box with 3-0 mud ring (provided by contractor). Use fixture mounting centers worksheet for location information. Note: It is critical that these dimensions are precisely followed. 2. Install drywall and complete finish work. 3. Slide cover plates over arms. 4. Slide threads through mounting plate, star washer and flat washer. 5. Securely tighten with nut - make sure mounting holes align with mud ring mounting holes. Note: Ensure arms are lined up correctly. 6. Completely wire make-up. 7. Securely mount fixture to wall with provided 8-32 flat undercut head screws. 8. Slide cover plate over mounting plate (magnets will pull the cover plate tight against wall.)
4 TORi Minimalist Linear SSM - Suspended Surface Mount 1. Drill necessary mounting holes and power feed and mounting in Housing in desired location. 2. Secure whip (by others) to housing 3. Secure housing to mounting surface (fasteners by others). 4. Make up necessary wires and install fixture lid assembly to housing. 5. Snap lid on 6. Install fixture by feeding cable into cable grippers on fixture Housing Fastener (supplied by others) 7. Install lamp and socket covers 8. Install accessory reflectors/lenses if applicable. Aircraft Cable Housing Lid Cable Gripper
5 TORi IB Minimalist Linear SM - Surface Mount 1-1/8 O SQUARE EXTRUDED HOUSING 2-1/2 T5 OR T5HO LAMP SOCKET COVER 1. Drill necessary mounting holes and power feed hole in mounting plate in desired location. 2. Secure whip (by others) to mounting plate 3. Secure mounting plate to mounting surface (fasteners by others). If wall make sure orientation of mounting plate is such that fixture will swing down to be installed (see illustration below). If mounting to a ceiling make sure to attached safety cables (provided) between mounting plate and fixture housing. 4. Make up necessary wires and install fixture housing assembly to lid. 5. Install lamp and accessory reflectors/lenses if applicable. Housing Mounting Plate
6 TORi RB Minimalist Linear Lamp Changing Guide PLUNGER SOCKET SOCKET COVER 1. Disconnect from power 2. Unscrew socket covers 3. Release lamp from static socket on opposite side 4. Remove socket covers from the old lamp and slide them on the new lamp. 5. install lamp and screw on socket covers 6. Install lamp and socket covers 7. Depress the plunger socket with lamp Unhook lamp from static socket and lower down Push lamp into plunger socket
INSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS This document explains mounting for pendant, recessed, and wall PENDANT - STEP ONE INSTALL MOUNTING POINTS Non-power feed mounting points may be positioned 1 to 12 or 12 to 18
More informationMEDIA LED. Pendant Standard Mount Installation ou de montage WARNING:
MEDIA LED Pendant Standard Mount WARNING: Disconnect main power at the source prior to installation! Thread gripper base onto 1 /4 20 stud, or with #8 screw. Depress gripper nozzle to insert aircraft cable.
More informationLED IMPORTANT SAFETY INSTRUCTIONS
READ AND FOLLOW ALL SAFETY INSTRUCTIONS! SAVE THESE INSTRUCTIONS AND DELIVER TO OWNER AFTER INSTALLATION To reduce the risk of death, personal injury or property damage from fire, electric shock, falling
More informationINSTALLATION INSTRUCTIONS HYLYTR WALL GRAZER
HYLYTR WALL GRAZER Page 1 of 11 IMPORTANT SAFETY INSTRUCTIONS When installing or using this recessed fixture basic safety precautions should be followed Read ALL INSTRUCTIONS before installing fixture.
More informationFluorescent Lamp Wattages. Fluorescent Optics T5 = F14 (2') F21 (3',6') F28 (4',8') NB Narrow Beam (60 ) WB Wide Beam (100 )
INDOOR R FLUORESCENT INDOOR R FLUORESCENT SMS/SMM MOUNT Prefix Mounting Optics Light Source & Wattage LIN = Linea SMS-U Surface, Uplight, SMM-U Surface, Uplight, Multiple Fixture Run SMS-D Surface, Downlight,
More informationNOTES: REQUIRES REMOTE DRIVER(S) (see page 4 for more info) LED DRIVE POWER DIRECT INDIRECT* VLO
PROJECT NAME: Carbon 2-3/4 1-3/4 EXTRUDED ALUMINUM USING MACHINED END CAPS PREMIUM LEDS WITH VARIOUS COR TEMPERATURES AND LIGHT OUTPUT FT GW FROSTED LENS TYPE: CABLE SUSPENDED (CS) FEATURES: Powered Suspension
More informationInde-Pendants Family. 32L Cylinder with Ring Chicago Plenum Ceiling Types. Document No
Inde-Pendants Family 32L with Ring Chicago Plenum Ceiling Types Installation instructions for: 32L-CRxx-P-ID-CCEA 32L-CRxx-P-D-CCEA Document No. 32L Inde-Pendants: with Ring (Plaster Trim, Grid and Drywall
More information1Unpack fixture. Suspensions/canopies are ordered and
DO NOT REMOVE THE LED ASSEMBLY. THIS WILL VOID THE WARRANTY. Call Zumtobel at 1-800-448-4131 questions. Fixture is intended installation in accordance with bee servicing. Retain these instructions 2Determine
More informationBSS610 GENERAL INFORMATION - FIXTURE HOUSING
BSS610 GENERAL INFORMATION - FIXTURE HOUSING 2 wide multi-axis direct LED luminaire system Project: Type: FEATURES Create an endless variety of multi-directional fixture runs and geometric shapes with
More informationCOLOR TEMP 2700K 3000K 3500K 4000K 5000K 27K 30K 35K 40K 50K. VLO Very Low Output CANOPY FINISH 5 SERIES CANOPY W G B CC.
: 1 CAB LE SUSPEN DED (CS) -5/1 DIA /4 aircraft cable suspension system /8 thick machined end caps 0 rotation option - with mechanical locking INTEGRAL WITH ALL OPTIONS EXTRUDED ALUMINUM VARIOUS ERATURES
More informationBSS610 GENERAL INFORMATION - FIXTURE HOUSING
BSS610 GENERAL INFORMATION - FIXTURE HOUSING 2 wide multi-axis direct LED luminaire system Project: Type: FEATURES Create an endless variety of multi-directional fixture runs and geometric shapes with
More informationHP-2 / HP-6 Direct Installation Instructions Overview
Overview Helpful Video 0-10V Dimming Step 1 Mounting & Suspension Page 2 Step 2 Identification & Preparation Page 3 Step 3 Mounting to Structure Page 4 NOTE Step 4 Page 5 This installation requires proper
More informationCOLOR TEMP LED DRIVE POWER 2700K 3000K 3500K 4000K 5000K. 465 lumens/ft (4w/ft.) 705 lumens/ft. (6w/ft.) 925 lumens/ft. (8w/ft.) VLO Very Low Output
: 1 CAB LE SUSPEN DED (CS) 3/4 aircraft cable suspension system Under steps MacAdams Ellipse Binning INTEGRAL (WITH ALL OPTIONS) - 7/8 VARIOUS ERATURES - 1/ ENTER FULL PART NUMBER HERE / ORIENTATION He
More informationNT-300 Series Single Circuit Track System & Accessories
NT-300 Series Single Circuit Track System & Accessories Type Project Catalog No. Lamp/Wattage PRODUCT DESCRIPTION Low profile, extruded aluminum track with 20-Amp rated flat, solid integral copper conductors.
More informationNOTE: The orientation of the mounting brackets are critical. (See Figure 4)
Page 1 of 5 11.25.13 Lamping Specifications 10138 I-wall 2 120v, One, F14WT5/Mini Bi-Pin 277v, One, F14WT5/Mini Bi-Pin 10139 I-wall 3 120v, One, F21WT5/Mini Bi-Pin, 277v, One, F21WT5/Mini Bi-Pin 10140
More informationC35. Assembly Instructions. Mobius Floor Lamp & C Page 1 of 7. Prepare Base (Figures 1& 2)
Mobius Floor Lamp 23-4505 & 23-4505C Page 1 of 7 Prepare Base (Figures 1& 2) A 8-32 Screw (2) B Wireway Cover Plate C Base D Lower Pipe Assembly E Threaded Stud (4) F Hex Nut (4) 1. Carefully unpack the
More informationCOLOR TEMP LED DRIVE POWER 2700K 3000K 3500K 4000K 5000K. 400 lumens/ft (4w/ft.) HO High Output. VLO Very Low Output. Consult factory CANOPY FINSH
1 CAB LE SUSPEN DED (CS) 3/4 aircraft cable suspension system Under steps MacAdams Ellipse Binning 30 rotation option - with mechanical locking -1/ -1/ ORIENTATION N CSD Cable Suspended DIRECT CSI Cable
More informationES44-LED SERIES DIRECT OR INDIRECT HIGH EFFICIENCY LED - RECESSED, SURFACE, WALL OR SUSPENDED
ES44-LED SERIES DIRECT OR INDIRECT HIGH EFFICIENCY LED - RECESSED, SURFACE, WALL OR SUSPENDED PERFORMANCE CHARACTERISTICS Optical Efficiency: 90.5% max Lumens per watt: 180 max Lumen output: 2200Lm/ft
More informationNOTES: REQUIRES REMOTE DRIVER(S) (see page 6 for more info) LED DRIVE POWER. 345 lumens/ft (4w/ft.) 520 lumens/ft. (6w/ft.) SO Standard Output
PROJECT NAME: TYPE: 1 QTY: CAB LE SUSPEN DED (CS) FEATURES: Powered Suspension System - No power cord High transmission frosted lenses with no diode imaging No visible fasteners Extruded aluminum housing
More informationC35 Mobius Floor Lamp & C Page 1 of 7
Mobius Floor Lamp 23-4505 & 23-4505C Page 1 of 7 Prepare Base (Figures 1& 2) A 8-32 Screw (2) B Wireway Cover Plate C Base D Lower Pipe Assembly E Threaded Stud (4) F Hex Nut (4) 1. Carefully unpack the
More informationCirca Ambient Interior Luminaire
IMPORTANT SAFETY INSTRUCTIONS 1. Read carefully before installing fixture. Retain for future reference. To prevent electrical shock, turn off electricity at fuse box before proceeding. 2. Failure to follow
More informationRECESSED WALL WASH MOUNT
PROJECT INFORMATION Project: Notes: Type: DIMENSIONS SECTION VIEWS 3 13/32 4 3/8" 4" IC culus Listed Type I.C. SHOWN WITH LENS OPTION ORDERING CODE 2 15/16 1 2 3 4 5 6 7 8 9 10 11 12 13 14 PRODUCT SPECIFICATIONS
More informationFEAT U RES : REQUIRES REMOTE DRIVER(S) (see page 3 for more info) LED DRIVE POWER
PROJECT NAME: TYPE: 1 QTY: Quark CAB LE SUSPEN DED (CS) FEAT U RES : 1-3/4 Powered Suspension System - No power cord High transmission frosted lenses with no diode imaging No visible fasteners Extruded
More informationUV8 & UV90 SERIES INSTALLATION INSTRUCTIONS
UV8 & UV90 SERIES INSTALLATION INSTRUCTIONS Important THIS SHEET CONTAINS IMPORTANT SAFETY INSTRUCTIONS. SAVE THESE INSTRUCTIONS. Warning This product must be installed in accordance with National Electrical
More informationFEAT U RES : REQUIRES REMOTE DRIVER(S) (see page 4 for more info) LED DRIVE POWER* COLOR TEMP 2700K 3000K 3500K 4000K 5000K
PROJECT NAME: TYPE: 1 QTY: Yttrium CAB LE SUSPEN DED (CS) FEAT U RES : SOFT GLOW FROSTED LENS PREMIUM LEDS WITH VARIOUS COLOR TEMPERATURES AND LIGHT OUTPUT EXTRUDED ALUMINUM SPOKES MACHINED COMPONENTS
More informationFINA SUSPENDED INSTALLATION INSTRUCTIONS
FINA SUSPENDED INSTALLATION INSTRUCTIONS 3 AC Cable Mounting (AC3) Installation... 2-4 AC Cable to Hub Mounting (AH4) Installation... 5-7 Pendant Pipe Mounting Installation... 8-9 Canopy Detail... 10-11
More informationLighting Systems Argus-7
Page 1 of 5 1 1. (3.5cm) 1.7 (4.3cm) 4 5 Rectilinear 3 1.81 (4.6cm) Extruded Linear Louver.5 (.64cm) 5. (1.7cm) 9. (.86cm) 1 1. (3.5cm) 1.7 (4.3cm) 4 5 Tapered 3 1.81 (4.6cm).75 (.7cm) Feature Specifications
More informationVerve IV. Suspended linear direct/indirect fluorescent with radial or flat baffle or parabolic louver.
FLUORESCENT BAFFLE/LOUVER radial blade baffle flat blade baffle flat blade parabolic louver DIMENSIONAL DATA FEATURES Suspended linear direct/indirect fluorescent with radial or flat baffle or parabolic
More informationCustomer service: or Upper mounting ring. Canopy
Components included: Upper mounting ring Canopy Fixture base Fluorescent - 2 x 42 W 4-pin compact fluorescent lamps required (not included). Lutron recommends GE, Sylvania, or Philips lamps that are certified
More informationMaxline Profile System - Suspension
DIRECT 5 7/8 150mm 6 1/4 158mm L3ML-SUS-SYS DR Article # Distribution Diffuser Length Angle Voltage Linear Spot Electrical Power Suspension Finishes Couplers Feed Cable x / / Accessories Product Distribution
More informationInstallation Instruction
T F W 604.549.9379 604.549.9555 fluxwerx.com Installation Instruction DRIVER ENCLOSURE Ceiling Type Version Grid Battery Pack GRID MOUNT INSTALL OPTIONS OPTION 1: Standard Vertical Grid drivers can be
More informationILLUMINA BS100 INSTALLATION INSTRUCTIONS FLUORESCENT VAPOR TIGHT
082114EC ILLUMINA BS100 INSTALLATION INSTRUCTIONS FLUORESCENT VAPOR TIGHT Beghelli Canada 3900 14th Avenue Markham, Ontario L3R 4R3 Canada P: (905) 948-9500 F: (905) 948-8673 www.beghellicanada.com Beghelli
More informationAIR by 3M Luminaire Installation Guide 3 ft. Pendant. Standard and Specialty Finishes A003-XX-3K-XX-XX A003-XX-4K-XX-XX. Installation Guide
Standard and Specialty Finishes A003-XX-3K-XX-XX A003-XX-4K-XX-XX Installation Guide Application AIR by 3M and supplied components (the Product ) comprise an LED pendant luminaire for dry, interior use.
More informationAssembly instruction. Pendant Light Toccata GENERAL REMARKS ON SAFETY: Technical data: BOM
GENERAL REMARKS ON SAFETY: Read all of these instructions before installing fixtures. Keep all of the instructions for future reference. Turn off power before installing fixture. Installation is to be
More informationWARNING NORDIC ALUMINIUM LIGHTING TRACK SYSTEMS
WARNING NORDIC ALUMINIUM LIGHTING TRACK SYSTEMS DO NOT solder connectors as this will prohibit the adapters circuit switch to move freely from circuit to circuit. Nordic Aluminium track adapters and accessories
More informationLuminaire Support Location Cable Mounting Kit. Non-Power Feed
INSTALLATION INSTRUCTIONS These installation instructions are used for installing the following luminaires and kits: Luminaire Support Location Cable Mounting Kit OLE4 (suspended) Normal Power Feed Non-Power
More informationINTEGRAL DRIVER(S) EXCEPT ON EM OPTIONS (See page 5 for more info) 2700K 3000K 3500K 4000K 5000K. 405 lumens/ft. (4w/ft.) 805 lumens/ft. (8w/ft.
PROJECT NAME: TYPE: Neodymium CAB LE SUSPEN DED (CS) FEAT U RES : /4 aircraft cable suspension system High transmission frosted lenses with no diode imaging No visible fasteners Extruded aluminum housing
More informationTRIPLANE TRP Suspended, Surface
TRIPLANE TRP Find additional images and information at alwusa.com/trp TRIPLANE TRP 1. BASE MODEL LED REMOTE DRIVER TRPSD 2.8" W x 2.9" H" suspended, direct with remote driver TRPSMB 2.8" W x 2.9" H" surface-mount,
More informationFIXTURE INSTALLATION GUIDE Model T21T (Low Voltage Pendant Set 120V)
FIXTURE INSTALLATION GUIDE Model T21T (Low Voltage Pendant Set 120V) 21T, Rev.4 6-13 IMPORTANT: Before proceeding, retrieve the GLASS SHADE INSTALLATION GUIDE, which is included with the pendant cord set
More informationHxO Profile System - Suspension
INDIRECT 1 14/16 47mm DIRECT L3HX-SUS-SYS DI OP X / / Article # Installation Distribution Diffuser Length Angle Couplers Voltage Linear Spot x Qty Electrical Power Feed Suspension Cable Finishes Lighting
More informationIdaho Profile System - Trimless
3 4/16 82mm DIRECT 3 9/16 90mm 3 6/16 85mm L3ID-TRI-SYS DR OP Article # Distribution Diffuser Length Voltage Linear Electrical Mounting Brackets Lighting Control Product Distribution Diffuser Length Voltage
More informationREQUIRES REMOTE DRIVER(S) (see page 3 for more info) LED DRIVE POWER VOLTAGE. ( v)
PROJECT NAME: TYPE: QTY: L E D CAB LE SUSPEN DED (CS) FEAT U RES : Powered Suspension System - No power cord Internal Light Glow No visible fasteners Extruded aluminum Dimmable/Programmable drivers for
More informationFIXTURE INSTALLATION GUIDE Model T21T (Low Voltage Pendant Set 120V)
FIXTURE INSTALLATION GUIDE Model T21T (Low Voltage Pendant Set 120V) 21T, Rev.4 6-13 IMPORTANT: Before proceeding, retrieve the GLASS SHADE INSTALLATION GUIDE, which is included with the pendant cord set
More informationOUTPUT. L: low lm/ft. R: regular lm/ft. CF: consult factory for. custom output MOUNT. SM: surface mount CM: cable mount
BSS610 YOX BUILD 2 wide multiaxis direct LED luminaire system Project: Type: FEATURES Create an endless variety of multidirectional fixture runs and geometric shapes with the BS610 YoX linear LED system.
More informationTrack Accessories. Single Circuit Track. L Connector T Connector X Connector. Mini Connector Floating Canopy End Feed Kit.
Single Circuit Single Circuit Track Live End Connector Flexible Connector Straight Connector Track supplied with dead end and mounting hardware Live end connector used for direct wiring Flexible connector
More informationFIXTURE INSTALLATION GUIDE Model T21T (Low Voltage Pendant Set 120V)
FIXTURE INSTALLATION GUIDE Model T21T (Low Voltage Pendant Set 120V) 21T, Rev.4 6-13 IMPORTANT: Before proceeding, retrieve the GLASS SHADE INSTALLATION GUIDE, which is included with the pendant cord set
More informationINSTALLATION INSTRUCTIONS For Light*Waves Flex II Kit with 300-Watt remote transformer
IMPORTANT SAFETY INSTRUCTIONS READ ALL OF THESE BEFORE INSTALLING THE TRACK SYSTEM. SAVE THESE INSTRUCTIONS AND REFER TO THEM WHEN ADDITIONS TO OR CHANGES TO THE SYSTEM ARE MADE. THIS IS A 12-VOLT SYSTEM
More informationSpecialty Finishes. AIR by 3M Installation Guide 7 ft. Pendant, Specialty Finishes. Installation Guide
Specialty Finishes A007-CH-3K-XX-XX A007-NI-3K-XX-XX A007-CH-4K-XX-XX A007-NI-4K-XX-XX Installation Guide Application AIR by 3M and supplied components (the Product ) comprise an LED pendant luminaire
More informationGavita TripleStar 600 EU
Gavita EU Adjustable: deep, medium, wide Symmetric / asymmetric Efficiency >90 % Miro aluminum reflector Replaceable reflector plates For MH/HPS lights up to 750 W Shielded terminals Gavita reflector The
More informationREQUIRES REMOTE DRIVER(S) (see page 5 for more info) LED DRIVE DIRECT. 378 lumens/ft. (4w/ft.) SO Standard Output. 748 lumens/ft. (8w/ft.
PROJECT NAME: TYPE: Palladium CAB LE SUSPEN DED (CS) FEAT U RES : Powered Suspension System - No power cord High transmission frosted lenses with no diode imaging No visible fasteners Extruded aluminum
More informationStyk Wall - Stem DESCRIPTION FEATURES & BENEFITS SPECIFICATIONS PROJECT DETAILS SIW Job Name: Type: Notes:
Styk Wall - Stem SIW12139 Job Name: Type: PROJECT DETAIS Notes: DESCRIPTION Styk was built to provide the most lumens with the smallest luminaire package, while optimizing life. Not limited to decorative
More informationAPPLICATIONS APPROVALS. GASKET One piece neoprene. LATCHES Plated steel twist draw. ENTRIES 1 2 NPT feed-through outlets, 3 4 NPT outlets optional.
Haz HazMax Pinnacle/al APPLICATIONS Hazardous locations Watertight requirements Dusttight requirements Oil and gas exploration and production Waste water treatment plants Pipeline compressor / pumping
More informationThe Tracking Magnet Recessed High-tech LED lighting system for interior architecture
Description The Tracking Magnet system is creative, flexible, reliable and precise. Accent fixtures can be rapidly exchanged and repositioned without tools using the magic of magnets. A variety of accent
More informationINSTALLATION INSTRUCTIONS
Sheet 1 of 5 General: Upon receipt of fixture thoroughly inspect for any freight damage, which should be brought to the attention of the delivery carrier. Compare the catalog description listed on the
More informationGeneral Installation Instructions LED
General Installation Instructions LED To reduce the risk of death, personal injury or property damage from fire, electric shock, falling parts, cuts/abrasions and other hazards, please read all warnings
More informationINTEGRAL DRIVER(S) EXCEPT ON EM OPTIONS (See page 7 for more info) 2700K 3000K 3500K 4000K 5000K. 420 lumens/ft. (4w/ft.) 830 lumens/ft. (8w/ft.
PROJECT NAME: TYPE: CAB LE SUSPEN DED (CS) FEAT U RES : 3/4 aircraft cable suspension system High transmission frosted lenses with no diode imaging No visible fasteners Extruded aluminum housing Dimmable/Programmable
More informationLumination TM LED Luminaires Suspended LED Fixture (Series EP14)
GE Lighting Solutions Installation Guide Lumination TM LED Luminaires Suspended LED Fixture (Series EP14) Features Long life (50,000 hour rated life) 5 year warranty IP30 Dry location rated BEFORE YOU
More informationInstall Guide PMX SERIES PENDANT MOUNTED MATRIX SP1 STYLE
PMX SERIES PENDANT MOUNTED MATRIX SP1 STYLE This product must be installed in accordance with the applicable code by a person familiar with the construction and operation of the product and the hazards
More informationCompose GYPSUM Mud-In
INSTALLATION Compose GYPSUM Mud-In Installation Instructions for Flat Front & Knife Edge 30 & 40 Page 1 of 5 WARNING Installation wall must have continuous blocking behind drywall for the entire length
More informationOne Circuit Trac System TRAC SECTION, JOINERS & FEEDS T Series
Project: Fixture Type: Location: Contact/Phone: PRODUCT DESCRIPTION DIMENSIONS Low-Profile, single-circuit trac sections for surface or pendant mounting. I-beam cross section provides added strength and
More informationFIXTURE INSTALLATION GUIDE Model T21T (Low Voltage Pendant Set 120V)
FIXTURE INSTALLATION GUIDE Model T21T (Low Voltage Pendant Set 120V) 21T, Rev.4 6-13 IMPORTANT: Before proceeding, retrieve the GLASS SHADE INSTALLATION GUIDE, which is included with the pendant cord set
More informationCIRRUS SUSPENSION WALL WASH WITH REMOTE POWER, END FEED
Adjustable Max. 5 ft. Description Cirrus Suspension Wall Wash with Remote 24VDC power supply (sold separately) is a linear LED fixture that offers a wall wash lens for a smooth and uniform beam spread.
More informationPROFILE 50 Up 50 Dn PF1-E. Luminaire PROFILE - 50 UP 50 DN LaED (PF1-E) Type. Project. Product. Notes. Performance Summary
T F W 604.549.9379 604.549.9555 fluxwerx.com PROFILE Specification Data PROFILE - 50 UP 50 DN LaED () Type Project Product Notes 50 Up I 50 Down A B C D Light (lm) 2350 2900 3500 4450 Energy (W) 19 24
More informationINSTALLATION MANUAL. Melink Corporation (513) Revision
INSTALLATION MANUAL Revision 130711 Table of Contents Step Installation Contractor Page 1 Install System Controller Electrical 4 2 Install Variable Frequency Drive Electrical 6 3 Install Touchpad Mechanical
More informationSurface Mount Explosion Proof, Waterproof Fluorescent Lights - T12 Very High Output - Oil Rigs - 2 L
Surface Mount Explosion Proof, Waterproof Fluorescent Lights - T12 Very High Output - Oil Rigs - 2 L Part #: EPL-48-2L-T12VHO Made in the USA The Larson Electronics EPL-48-2L-T12VHO Explosion Proof Fluorescent
More information003 3 foot foot RUN Nominal Length* * For actual lengths see
M125 Project: Type: Qty: Series Lamping Shielding Mounting Nominal Length Finish Voltage Options Series Lamping Shielding Mounting Nominal Length Finish Voltage Options M125 (M125/9 Direct) Multi-Mount
More informationNOVENTA NV3.5 SUSPENDED, WALL, SURFACE, RECESSED. STANDARD SIZES 3.5" Aperture corner profile Configurable in individual straight run sections
NOVENTA NV3.5 SUSPENDED,, SURFACE, RECESSED STANDARD SIZES 3.5" Aperture corner profile Configurable in individual straight run sections LAMPING LED - Direct or Indirect - 80/90 CRI - 3000K/3500K/4000K
More informationWALL MOUNT. Notes: Project: Type: PROJECT INFORMATION DIMENSIONS SECTION VIEWS ORDERING CODE PRODUCT SPECIFICATIONS
PROJECT INFORMATION Project: Notes: Type: DIMENSIONS SECTION VIEWS 3 1/16" 78mm 4 102mm 4 102mm 4 3/8 111mm ORDERING CODE 1 2 3 4 5 6 7 8 9 10 11 12 13 PRODUCT SPECIFICATIONS 1 PRODUCT ID 2 OPTICS 3 LENGTH/FT
More informationRECESSED ASYMMETRIC MOUNT
PROJECT INFORMATION Project: Notes: Type: DIMENSIONS SECTION VIEWS 5" SHOWN WITH LENS OPTION 3 13/32 ORDERING CODE 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 PRODUCT SPECIFICATIONS 1 PRODUCT ID 2 OPTICS 3
More informationNotes: (1) not recommended with staggered lamping (2) Not available with T8 lamping.
PROJECT INFORMATION Project: Notes: Type: DIMENSIONS SECTION VIEW 3 5/8" 92mm 2 1/4 57mm ORDERING CODE 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 PRODUCT SPECIFICATIONS 1 PRODUCT ID 2 OPTICS 3 LENGTH (FT)
More informationHP-4 Recessed with Regressed Visible Flange Starter/Independent Installation Instructions
HP-4 Recessed with Regressed Visible Flange /Independent Scan QR code for helpful video(s) Step 1 Cutout Dimension Step 2 Step 3 0-10V 5" 7/8" Feed "A" A + 1/4" +/- 1/1 3/4" Nominal Length Add 1/4" to
More informationAnthony LED Lighting System Retrofit Installation Instructions For Models 101X and 101A
Anthony LED Lighting System Retrofit Installation Instructions For Models 101X and 101A 99-16999-0000 Table of Contents 1. Removing Fluorescent Lighting... 4 1.1. Detach the lens assembly... 4 1.2. Remove
More informationREQUIRES REMOTE DRIVER(S) (see page 7 for more info) LED DRIVEPOWER
PROJECT NAME: TYPE: 1 QTY: CAB LE SUSPEN DED (CS) FEAT U RES : Powered Suspension System - No power cord High transmission frosted lenses with no diode imaging No visible fasteners Extruded aluminum housing
More informationMONORAIL KITS INSTALLATION INSTRUCTIONS PENDANTS
MONORAIL KITS PENDANTS JESCO Lighting Group is a UL and ETL listed company Copyright 2011 JESCO Lighting Group. All rights reserved. IMPORTANT SAFETY INSTRUCTIONS Be sure to read and unsderstand the following
More informationSeem mm 4.50" 4.00" 101.6mm. Narrow 4" linear fluorescent allows for both individual or continuous runs.
FLUORESCENT recessed companion wall mount companion DIMENSIONAL DATA FEATURES Narrow 4" linear fluorescent allows for both individual or continuous runs. Frosted acrylic flush lens provides even illumination,
More informationRunning Magnet 2.0 Suspension Down High-tech LED lighting system for interior architecture
Description Fun with magnets and light. Simultaneously graphic and subtle, the Running Magnet is flexible, precise, and as creative as you. It is track lighting redesigned and elegantly refined. Light
More information98PF-P-I Perforated Pendant Indirect. Ordering Guide. Key Features 98-P-I-PF. Fixture Type: Project Name: Quick Find litecontrol.
Fixture Type: Project Name: Ordering Guide Feature Code Options Description Series 98 9800 Housing Style PF Perforated Mounting P Pendant Fixture distribution I Indirect Row length (in feet) Enter in foot
More information2700K 3000K 3500K 4000K 5000K. 480 lumens/ft. (4w/ft.) 950 lumens/ft. (8w/ft.) HO High Output. 1,190 lumens/ft. (10w/ft.) VHO Very High Output
PROJECT NAME: TYPE: 1 QTY: CAB LE SUSPEN DED (CS) FEAT U RES : 3-5/1 DIA EXTRUDED ALUMINUM HOUSING INTEGRAL WITH ALL FIXTURE OPTIONS PREMIUM LEDS WITH VARIOUS TEMPERATURES AND LIGHT OUTPUT 1/1 aircraft
More informationAvenue A. Grid Mount. Drywall Flange. lens. Narrow aperture high performance T5/T5HO asymmetric wall wash.
FLUORESCENT drywall row mount open optic clear lens mr16 companion linear recessed wall mount DIMENSIONAL DATA Grid Mount 4.00" 101.60mm.54" 13.72mm Drywall Flange 2.20" 55.88mm 3.20" 81.28mm 4.3" 109.22mm
More informationAvenue A. Grid Mount. Drywall Flange. lens. Narrow aperture high performance T5/T5HO asymmetric wall wash.
Avenue A FLUORESCENT drywall row mount open optic clear lens mr16 companion linear recessed wall mount DIMENSIONAL DATA Grid Mount 4.00" 101.60mm.54" 13.72mm Drywall Flange 2.20" 55.88mm 3.20" 81.28mm
More informationLLCRC LED. RC LED Linear Lighting Channel EXAMPLE: LLCRC48LED42SA WATT CAT# APPLICATIONS FEATURES & SPECIFICATIONS
APPLICATIONS Mobern introduces an eye catching selection of LED Linear Lighting channels that can be surface or pendant mounted individually or in a continuous run that put a line of light where you want
More informationLIGHTPLANE 1 RECESSED - LP1R
INSTRUCTIONS LIGHTPLANE 1 RECESSED - LP1R Safety & Warnings! When installing or using this recessed fixture basic safety precautions should be followed: 1. Read ALL INSTRUCTIONS before installing 2. This
More informationGeartray mounts onto extrusion with 1/4 turn hardware. Lamp support ring. MR11 Lamp 50W max. (supplied by others) End View Side View Bottom View
MR11 Downlights MR11 Fixed Downlight Ordering Code: MR11 Supplied with clear glass lens. Available for all M60 extruded forms. Fixture will accept up to 3 accessories. 50W MR11 Lamps (by others) must be
More informationBionic Perimeter Standard C o v e & P e r i m e t e r
Type Job Name Catalog Number Bionic Perimeter Standard C o v e & P e r i m e t e r 5 7 /16" 110mm 6 7 /16" 170mm 8 7 /16" 221mm Flush Regress 3" Regress ordering - BIO-PSTD (STANDARD) series/ style lamp
More informationPARTS AND SERVICE MANUAL
PARTS AND SERVICE MANUAL FOR THE 23 INSERT FIREPLACE MODEL NUMBER: DFI2309 TABLE OF CONTENTS OPERATION PAGE 1 PARTS DRAWING PAGE 3 PARTS LIST PAGE 4 WIRING DIAGRAM PAGE 5 LIGHT BULB REPLACEMENT PAGE 6
More informationLow Profile T-Bar Power Supply Box shown. ELECTRICAL BOX OPTIONS Mounting options for new and retrofit installations. See page 2 for more information.
10 Industry Best Year LED Warranty Signal White is standard finish Top Glow Shown Date Project Type Comments Canopy DESCRIPTION provides excellent light output with a minimalist shape. Based on the Elements
More informationZynn Lines - Pendant. AIP in DESCRIPTION FEATURES & BENEFITS SPECIFICATIONS PROJECT DETAILS JOB NAME: TYPE: NOTES:
Zynn Lines - Pendant AIP12116 49 in JOB NAME: TYPE: NOTES: PROJECT DETAILS DESCRIPTION With a cross-section of just 1.25", Zynn Lines suspends slim lines of light in contemporary spaces. Its seamless housing,
More informationApollo 8. lamping. patient bed pair example. 8" wide recessed patient bed light with exam function available in 2', 3' & 4' lengths.
FLUORESCENT RECESSED PATIENT BED LIGHT SYSTEM apollo 8 ambient only integral LED apollo 1 & 2 companion DIMENSIONAL DATA FEATURES 8" wide recessed patient bed light with exam function available in 2',
More informationCOLOR TEMP 2700K 3000K 3500K 4000K 5000K 27K 30K 35K 40K 50K. HO High Output. VLO Very Low Output CANOPY FINISH 5 SERIES CANOPY W G B CC
PROJECT NAME: TYPE: CAB LE SUSPEN DED (CS) FEAT U RES : /4 aircraft cable suspension system High transmission frosted lenses with no diode imaging No visible fasteners Extruded aluminum housing Dimmable/Programmable
More informationREQUIRES REMOTE DRIVER(S) (see page 5 for more info) LED DRIVE POWER
PROJECT NAME: TYPE: Thallium CAB LE SUSPEN DED (CS) FEAT U RES : Powered Suspension System - No power cord High transmission frosted lenses with no diode imaging No visible fasteners Extruded aluminum
More informationFULL BLEED APPLICATION SHOT RENDERING
KM FULL BLEED APPLICATION SHOT RENDERING K1 M1 KM ANATOMY POWERFUL PERFORMANCE K1 1.50 High performance Nichia 80+ CRI LEDs provide an optimal source for tailored ing design. 0.75 optional aperture 7.00
More informationStrip Fixture URS Light Bar Retrofit Installation Instructions Revised:
Strip Fixture URS Light Bar Retrofit Installation Instructions Revised: 20180126 These instructions do not purport to cover all details or variations in components nor to provide for every possible contingency
More informationInstallation Instructions
Installation Instructions 2-Post Capacity 12,000 lbs. OPERATING CONDITIONS Lift is not intended for outdoor use and has an operating ambient temperature range of 41-104 F (5-40 C) IMPORTANT Reference ANSI/ALI
More informationInstallation Operation Care
Installation Operation Care Alustra Woven Textures Standard and Cassette Roller Shades CONTENTS Getting Started: Product View...1 Tools and Fasteners Needed...2 Installation: Installation Overview...3
More informationMaterials List: Tools List:
Materials List: Anchor assembly Automated power supply Automated power supply hardware packet Automation bracket assembly Automation bracket assembly hardware packet Automation winch assembly Cable Cable
More informationSection A: CUSTOMER INFORMATION. Customer Name Electric Account Number Rate Application Number. Facility Address City State Zip Code
Commercial & Municipal Retrofit 2015 Lighting Rebate Section A: CUSTOMER INFORMATION Customer Name Electric Account Number Rate Application Number Facility Address City State Zip Service Location Identification
More informationClutch Operated Roller Shade with Fascia Installation Instructions
Clutch Operated Roller Shade with Fascia Installation Instructions Tools Required for Installation: Power Drill & Drill Bits Installation Screws Level Pliers Measuring Tape Step #1 Bracket Installation
More informationNorthstar RIM Tach Steps to Installation. K Wheel (Clamp Style)
Northstar RIM Tach 8500 10 Steps to Installation K Wheel (Clamp Style) Mill Duty High Performance & Rugged Most Reliable magneto-resistive digital tach on the market today Ductile Iron Housing & Stainless
More informationREQUIRES REMOTE DRIVER(S) (see page 4 for more info) Continuous Run requires the rotational option LED DRIVE DIRECT. 455 lumens/ft. (4w/ft.
PROJECT NAME: TYPE: Radium 1 QTY: CAB LE SUSPEN DED (CS) FEAT U RES : EXTRUDED ALUMINUM PREMIUM LEDS WITH VARIOUS TEMPERATURES AND LIGHT OUTPUT HIGH EFFICACY REFLECTOR -7/8 LIGHT STREAM SIDE LIGHT OR LINEAR
More informationNera. detail. fixture information. Unique aesthetic inspired by the visual void design philosophy. Luminaire sizes available in 2 x2, 3 x3 and 4 x4.
LED bottom detail inside lens detail white finish palladium finish 2016 DIMENSIONAL DATA FEATURES Unique aesthetic inspired by the visual void design philosophy. Luminaire sizes available in 2 x2, 3 x3
More information