FINA SUSPENDED INSTALLATION INSTRUCTIONS
|
|
- Luke Jackson
- 5 years ago
- Views:
Transcription
1 FINA SUSPENDED INSTALLATION INSTRUCTIONS 3 AC Cable Mounting (AC3) Installation AC Cable to Hub Mounting (AH4) Installation Pendant Pipe Mounting Installation Canopy Detail Surface Mount Installation
2 FINA SUSPENDED 3 AC CABLE MOUNTING INSTALLATION (AC3)
3 3 AC Cable Mounting (AC3) Return to Step 1: Mounting Prep 1. If mounting to utilize flush canopy, prep for ring to be recessed into ceiling. 2. Install proper J-box to support fixture weight, and secure to structure. (see chart A) 3. Run SJT cord through canopy and strain relief bracket into J-box and secure with strain relief, make necessary wiring connections. 4. Install Mounting bracket, and attach canopy to mounting bracket. (see page 2 for details) Flush Canopy 4 - Octagonal J-box (by others) Ring 0.89 Strain Relief Strain Relief Bracket SJT Cord Standard Canopy Chart A Actual Size Max Weight 10lbs lbs /16 20lbs /16 55lbs /16 75lbs. Mounting Bracket Canopy AC cables with damage, bends, kinks, fraying, or knots must be discarded and replaced with new components. Never install a fixture where the AC cable is more than 5 degrees from perpendicular to the fixture. Fixtures are never to be raised by the cables (instead, lift the fixture up and adjust the cable position). Overtightening of hardware on grippers can damage AC cables. Never exert force down onto the top of the fixture once it is hanging by safety cables. Never cut safety cables prior to installation. The first zip tie on the SJT and AC cables below the ceiling/canopy must be no closer than 12 from the ceiling/canopy 2016 Pinnacle Architectural Lighting 3 of 14
4 3 AC Cable Mounting (AC3) Return to Step 2: Hanging the Fixture 1. Attach AC Cable grippers to fixture, using 3/32 allen wrench fixture has three (3) mounting points for AC cable. 2. Attach AC cables to grippers and adjust cables up or down to level fixture. (see mounting chart for minimum mouting heights) Mounting Height Chart A B Fixture Size (A) Min AC Length (B) 5-3/4 6-1/ /2 AC cables with damage, bends, kinks, fraying, or knots must be discarded and replaced with new components. Never install a fixture where the AC cable is more than 5 degrees from perpendicular to the fixture. Fixtures are never to be raised by the cables (instead, lift the fixture up and adjust the cable position). Overtightening of hardware on grippers can damage AC cables. Never exert force down onto the top of the fixture once it is hanging by safety cables. Never cut safety cables prior to installation. The first zip tie on the SJT and AC cables below the ceiling/canopy must be no closer than 12 from the ceiling/canopy 2016 Pinnacle Architectural Lighting 4 of 14
5 FINA SUSPENDED 4 AC CABLE TO HUB MOUNTING INSTALLATION (AH4)
6 4 AC Cable to Hub Mounting (AH4) Return to Step 1: Mounting Prep 1. If mounting to utilize flush canopy, prep for ring to be recessed into ceiling. 2. Install proper J-box to support fixture weight, and secure to structure. (see chart A) 3. Run SJT cord through canopy and strain relief bracket into J-box and secure with strain relief, make necessary wiring connections. 4. Install Mounting Bracket, and attach canopy to mounting bracket. (see page 2 for details) Flush Canopy 4 - Octagonal J-box (by others) Ring Strain Relief 0.89 Strain Relief Bracket SJT Cord Mounting Bracket Standard Canopy Chart A Actual Size Max Weight 10lbs lbs /16 20lbs /16 55lbs /16 75lbs. Canopy Hub AC cables with damage, bends, kinks, fraying, or knots must be discarded and replaced with new components. Never install a fixture where the AC cable is more than 5 degrees from perpendicular to the fixture. Fixtures are never to be raised by the cables (instead, lift the fixture up and adjust the cable position). Overtightening of hardware on grippers can damage AC cables. Never exert force down onto the top of the fixture once it is hanging by safety cables. Never cut safety cables prior to installation. The first zip tie on the SJT and AC cables below the ceiling/canopy must be no closer than 12 from the ceiling/canopy 2014 Pinnacle Architectural Lighting 6 of 14
7 Return 4 AC Cable to Hub Mounting (AH4) to Step 2: Hanging the Fixture 1. Attach AC Cable grippers to fixture, using 3/32 allen wrench fixture has four (4) mounting points for AC cable. 2. Attach AC cables to grippers and adjust cables up or down to level fixture. (see mounting chart for minimum mouting heights) A Mounting Height Chart AC cables with damage, bends, kinks, fraying, or knots must be discarded and replaced with new components. Never install a fixture where the AC cable is more than 5 degrees from perpendicular to the fixture. Fixtures are never to be raised by the cables (instead, lift the fixture up and adjust the cable position). Overtightening of hardware on grippers can damage AC cables. Never exert force down onto the top of the fixture once it is hanging by safety cables. Never cut safety cables prior to installation. The first zip tie on the SJT and AC cables below the ceiling/canopy must be no closer than 12 from the ceiling/canopy B Fixture Size (A) Min AC Length (B) 5-3/4 6-1/ / Pinnacle Architectural Lighting 7 of 14
8 FINA SUSPENDED PENDANT PIPE MOUNTING INSTALLATION (PP/PS)
9 Pendant Pipe Mounting (PP/PS) Return to Step 1: Prepping the Fixture 1. Start by running the required wires through the pendant and making wiring connections at the fixture, recess connections into fixture. 2. Pendant has threaded end, screw into threaded mount hole in fixture. Step 2: Mounting the Fixture 1. If mounting to utilize flush canopy, prep for ring to be recessed into ceiling. 2. Install proper J-box to support fixture weight, and secure to structure. (see chart A) 3. Install Ring, and mounting bracket to J-box. 4. Lift Fixture and Pendant to Mounting Bracket and slide Pendant Bracket. If using PP Pendant Plate will lock into mounting bracket, then screw on nut. 5. Make wire connections and recess connections into J-box, lift and secure canopy. (see page 2) 4 - Octagonal J-box (by others) Ring Flush Canopy 0.89 Nut Pendant Plate Mounting Bracket Pendant Ball Pendant Canopy Standard Canopy Chart A Actual Size Max Weight 10lbs lbs /16 20lbs /16 55lbs /16 75lbs Pinnacle Architectural Lighting 9 of 14
10 FINA SUSPENDED CANOPY DETAIL
11 Canopy Detail Return to Step 1: Canopy Installation 1. Fold down spring tabs to secure spring clip. 2. Pull up the arms of the spring clips, both clips. 3. Slide spring clip arms into holes in mounting bracket. 4. Springs will straighten themselves securing the canopy to the mounting bracket. Step 2: Canopy Removal 1. Pull bracket down away from mounting plate. 2. Spring clip arms will hold onto mounting bracket. To disengage squeeze the arms together and pull them out of the mounting bracket. Mounting Bracket Spring Clip Arm Spring Clips Spring Tabs Canopy Final View 2014 Pinnacle Architectural Lighting 11 of 14
12 FINA SUSPENDED SURFACE MOUNT INSTALLATION
13 Surface Mount Return to Step 1: Mounting Prep 1. Install proper support to structure in ceiling/ wall to hold fixture weight (see chart a) 2. Install proper J-Box (by others). Step 2: Making the Connections 1. Remove conduit cover on fixture. 2. Make necessary wiring connections to building power. 3. Recess wires into J-Box. Dim A Dim B Dim C Dim D Conduit Cover Top View Chart A Dim A Dim B Dim C Dim D / / /16 N/A 4 4 N/A N/A 6-1/4 N/A N/A 12-1/8 16-1/2 N/A 6 6 N/A N/A Chart B Actual Size diameter Max Weight 10lbs lbs /16 20lbs /16 55lbs /16 75lbs Pinnacle Architectural Lighting 13 of 14
14 Surface Mount Return to Step 3: Mounting 1. Remove lens by rotating counter clockwise. 2. Knock out the four (4) 7/8 mount holes, and mount fixture to surface using appropriate 1/4 hardware (by others) 3. Once mounted, plug mount holes using supplied Knockout plugs. Step 4 Finishing 1. Reinstall the lens, by turning is clockwise to engage the four (4) lens pins, lift and turn. Make sure all four (4) pins engage the lens. Note: Lens will have white gasketing, do not remove or warranty will be voided. 7/8 Mounting Knockout Knockout plugs F14-4 knockouts F18/ F24-3 knockouts F36/ F48-4 knockouts 2014 Pinnacle Architectural Lighting 14 of 14
INSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS This document explains mounting for pendant, recessed, and wall PENDANT - STEP ONE INSTALL MOUNTING POINTS Non-power feed mounting points may be positioned 1 to 12 or 12 to 18
More informationMEDIA LED. Pendant Standard Mount Installation ou de montage WARNING:
MEDIA LED Pendant Standard Mount WARNING: Disconnect main power at the source prior to installation! Thread gripper base onto 1 /4 20 stud, or with #8 screw. Depress gripper nozzle to insert aircraft cable.
More informationZIP LIGHT LED LUMINAIRE
LED LUMINAIRE INSTALLATION MANUAL Note: Follow the Electrical Codes of the Country where this fixture will be installed. For Canada follow the Canadian Electrical Code (CE) and for the United States follow
More informationLuminaire Support Location Cable Mounting Kit. Non-Power Feed
INSTALLATION INSTRUCTIONS These installation instructions are used for installing the following luminaires and kits: Luminaire Support Location Cable Mounting Kit OLE4 (suspended) Normal Power Feed Non-Power
More informationTrack Accessories. Single Circuit Track. L Connector T Connector X Connector. Mini Connector Floating Canopy End Feed Kit.
Single Circuit Single Circuit Track Live End Connector Flexible Connector Straight Connector Track supplied with dead end and mounting hardware Live end connector used for direct wiring Flexible connector
More informationES44-LED SERIES DIRECT OR INDIRECT HIGH EFFICIENCY LED - RECESSED, SURFACE, WALL OR SUSPENDED
ES44-LED SERIES DIRECT OR INDIRECT HIGH EFFICIENCY LED - RECESSED, SURFACE, WALL OR SUSPENDED PERFORMANCE CHARACTERISTICS Optical Efficiency: 90.5% max Lumens per watt: 180 max Lumen output: 2200Lm/ft
More information1Unpack fixture. Suspensions/canopies are ordered and
DO NOT REMOVE THE LED ASSEMBLY. THIS WILL VOID THE WARRANTY. Call Zumtobel at 1-800-448-4131 questions. Fixture is intended installation in accordance with bee servicing. Retain these instructions 2Determine
More informationInstall Guide PMX SERIES PENDANT MOUNTED MATRIX SP1 STYLE
PMX SERIES PENDANT MOUNTED MATRIX SP1 STYLE This product must be installed in accordance with the applicable code by a person familiar with the construction and operation of the product and the hazards
More informationNT-300 Series Single Circuit Track System & Accessories
NT-300 Series Single Circuit Track System & Accessories Type Project Catalog No. Lamp/Wattage PRODUCT DESCRIPTION Low profile, extruded aluminum track with 20-Amp rated flat, solid integral copper conductors.
More informationWhen using electrical equipment, basic safety precautions should always be followed including the following:
INDUSTRIAL INSTALLATION INSTRUCTIONS Illumina BS100LED2FT-PLUS EACH MODEL NUMBER CONSISTS OF THE FOLLOWING: SERIES / LENGTH / OPERATION / LUMENS / COLOUR TEMP. / INPUT SERIES: LENGTH: OPERATION: BS100LED2PLUS
More informationInstallation Instruction
T F W 604.549.9379 604.549.9555 fluxwerx.com Installation Instruction DRIVER ENCLOSURE Ceiling Type Version Grid Battery Pack GRID MOUNT INSTALL OPTIONS OPTION 1: Standard Vertical Grid drivers can be
More informationFINA F48B 48 Direct and Uplight Architectural Round
Project Name Date Type FINA F48B 48 Direct and Uplight Architectural Round 4-1/2 4-7/8 (114.3mm) (123.8mm) 45-15/16 (1166.8mm) Key Features Extruded aluminum housing is rolled and welded for seamless finish
More informationILLUMINA BS100 INSTALLATION INSTRUCTIONS FLUORESCENT VAPOR TIGHT
082114EC ILLUMINA BS100 INSTALLATION INSTRUCTIONS FLUORESCENT VAPOR TIGHT Beghelli Canada 3900 14th Avenue Markham, Ontario L3R 4R3 Canada P: (905) 948-9500 F: (905) 948-8673 www.beghellicanada.com Beghelli
More informationSeries DKS 2"W Low Profile LED Surface Mount
2"W FEATURES & SPECIFICATIONS INTENDED USE Full body micro silhouette makes a bold statement with a minimal design in brushed nickel powder coated finish (consult factory for other finishes). Scaled to
More informationNETBOOK CART DIVIDER WIRING INSTRUCTIONS Extra cord
NETBOOK CART DIVIDER WIRING INSTRUCTIONS Extra cord Ensure there is slack here Lay divider flat on work surface. Lay laptop and power brick on top of divider, with the computer end of the power wire towards
More informationLumination TM LED Luminaires Suspended LED Fixture (Series EP14)
GE Lighting Solutions Installation Guide Lumination TM LED Luminaires Suspended LED Fixture (Series EP14) Features Long life (50,000 hour rated life) 5 year warranty IP30 Dry location rated BEFORE YOU
More information1718 W. Fullerton Ave Chicago, IL Tel: Fax:
206 Edge Lighting. All Rights Reserved. Installation Instructions for Nova Power Suspension Up/Down - Center Feed Glide Up/Down - Center Feed IMPORTANT INFORMATION - This product is suitable for indoor
More informationAIR by 3M Luminaire Installation Guide 3 ft. Pendant. Standard and Specialty Finishes A003-XX-3K-XX-XX A003-XX-4K-XX-XX. Installation Guide
Standard and Specialty Finishes A003-XX-3K-XX-XX A003-XX-4K-XX-XX Installation Guide Application AIR by 3M and supplied components (the Product ) comprise an LED pendant luminaire for dry, interior use.
More informationFINA F48 48 Direct and Uplight Architectural Round
Project Name Date Type 48 Direct and Uplight Architectural Round 4-1/2 4-7/8 (114.3mm) (123.8mm) 45-15/16 (1166.8mm) Key Features Extruded aluminum housing is rolled and welded for seamless finish with
More informationSpecialty Finishes. AIR by 3M Installation Guide 7 ft. Pendant, Specialty Finishes. Installation Guide
Specialty Finishes A007-CH-3K-XX-XX A007-NI-3K-XX-XX A007-CH-4K-XX-XX A007-NI-4K-XX-XX Installation Guide Application AIR by 3M and supplied components (the Product ) comprise an LED pendant luminaire
More informationFINA F36B 36 Bidirectional Architectural Round
Project Name Date Type FINA F36B 36 Bidirectional 4-1/2 4-7/8 (114.3mm) (123.8mm) 33-15/16 (862mm) Key Features Extruded aluminum housing is rolled and welded for seamless finish with 1/4 trim Aluminum
More informationLIGHTPLANE 1 RECESSED - LP1R
INSTRUCTIONS LIGHTPLANE 1 RECESSED - LP1R Safety & Warnings! When installing or using this recessed fixture basic safety precautions should be followed: 1. Read ALL INSTRUCTIONS before installing 2. This
More informationLED IMPORTANT SAFETY INSTRUCTIONS
READ AND FOLLOW ALL SAFETY INSTRUCTIONS! SAVE THESE INSTRUCTIONS AND DELIVER TO OWNER AFTER INSTALLATION To reduce the risk of death, personal injury or property damage from fire, electric shock, falling
More informationECO-T LED RECESSED TROFFER USER MANUAL
ECO-T LED RECESSED TROFFER USER MANUAL INSTALLATION GUIDE FOR: 2X2: MLRT22D4535 MLRT22D4541 MLRT22D4550 2X4: MLRT24D5535 MLRT24D5541 MLRT24D5550 Thank you for purchasing this MaxLite product. For additional
More informationGEMINI HOUSING SPECIFICATIONS
GEMINI HOUSING SPECIFICATIONS GENERAL Gemini Housing shall support Track of six foot intervals. In addition, the extra compartment shall be able to be used for a multitude of elec trical or mechanical
More informationSeries SKD 2"W Low Profile LED Surface Mount
FEATURES & SPECIFICATIONS INTENDED USE Full body micro silhouette makes a bold statement with a minimal design in brushed nickel powder coated finish (consult factory for other finishes). Scaled to the
More informationInde-Pendants Family. 32L Cylinder with Ring Chicago Plenum Ceiling Types. Document No
Inde-Pendants Family 32L with Ring Chicago Plenum Ceiling Types Installation instructions for: 32L-CRxx-P-ID-CCEA 32L-CRxx-P-D-CCEA Document No. 32L Inde-Pendants: with Ring (Plaster Trim, Grid and Drywall
More informationHP-2 / HP-6 Direct Installation Instructions Overview
Overview Helpful Video 0-10V Dimming Step 1 Mounting & Suspension Page 2 Step 2 Identification & Preparation Page 3 Step 3 Mounting to Structure Page 4 NOTE Step 4 Page 5 This installation requires proper
More informationMAXTRAC SUSPENSION 4030 E LEAVERTON CT ANAHEIM, CA
MAXTRAC SUSPENSION 4030 E LEAVERTON CT ANAHEIM, CA 92807 714 630 0363 WWW.MAXTRACSUSPENSION.COM SALES@MAXTRACSUSPENSION.COM PRODUCT: PARTS LIST K751364 6" LIFT KIT 07 12 GM 1500 PICKUP QTY SPINDLE, CHEVY
More informationMOUNTING SYSTEMS SPECIFICATIONS
MOUNTING SYSTEMS SPECIFICATIONS GENERAL Mounting Systems shall allow Track Systems to be fastened to or from various surfaces in a wide range of safe and approved methods. Mounting Systems shall have a
More informationA B C D E F. b.tools Required (supplied by others) 3/16" Drill Bit 3/8" Wrench Phillips Head Screwdriver
Page 1 of 13 5E.1 Parts List a. Below Deck Automatic Retractable Security Cover Kit (1) Tube End Bearing Plate (A) (1) Rope Reel with Motor Attached (B) (1) Rope Reel Cover (C) (1) Cover Drum (1) Cover
More informationUV8 & UV90 SERIES INSTALLATION INSTRUCTIONS
UV8 & UV90 SERIES INSTALLATION INSTRUCTIONS Important THIS SHEET CONTAINS IMPORTANT SAFETY INSTRUCTIONS. SAVE THESE INSTRUCTIONS. Warning This product must be installed in accordance with National Electrical
More informationGeneral Installation Instructions LED
General Installation Instructions LED To reduce the risk of death, personal injury or property damage from fire, electric shock, falling parts, cuts/abrasions and other hazards, please read all warnings
More informationTORi INSTRUCTION SHEET. Minimalist Linear Fixture T5/T5HO. CSS - Cable Suspended. 1. Cut cables to desired length - take care not to fray cable ends.
TORi Minimalist Linear CSS - Cable Suspended J-BOX (BY OTHERS) 3-O or 4-0 MUD RING (BY OTHERS) J-BOX BRACKET BAR 1/4-20 STUD 8-32 BRACKET BAR SCREWS (BY OTHERS) CANOPY STND - 5 CANOPY 1. Cut cables to
More informationDMV. 24 System Watts, 2400 Delivered Lumens 28 System Watts, 2700 Delivered Lumens. *Field installed-dimming Wire
HSL - 2 W FEATURES & SPECIFICATIONS INTENDED USE Full body micro silhouette makes a bold statement with a minimal design in brushed nickel powder coated finish (consult factory for other finishes). Scaled
More informationOSQ Series IMPORTANT SAFEGUARDS READ AND FOLLOW ALL SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE. LED Area Light TO INSTALL:
OSQ Series LED Area Light Direct Pole Mount IMPORTANT SAFEGUARDS When using electrical equipment, basic safety precautions should always be followed including the following: READ AND FOLLOW ALL SAFETY
More informationWARNING NORDIC ALUMINIUM LIGHTING TRACK SYSTEMS
WARNING NORDIC ALUMINIUM LIGHTING TRACK SYSTEMS DO NOT solder connectors as this will prohibit the adapters circuit switch to move freely from circuit to circuit. Nordic Aluminium track adapters and accessories
More informationBe sure pins are actually seated in their respective slots before applying any pressure.
1. Turn adjusting screw until outer collar is at it s lowest limit of travel. Do this for EACH cut. Adjusting Screw Upper Trunnion Lower Trunnion 2. Slide chain under pipe at location of cut. 3. Using
More informationA CHANNEL. Installation Instructions for Tie Stix Wall 2-Light. Section One: 4SQ Version
0 Edge Lighting. All Rights Reserved. W. Fullerton Ave Chicago, IL 0 Tel: -0- Fax: -- www.edgelighting.com info@edgelighting.com Installation Instructions for Tie Stix Wall -Light IMPORTANT INFORMATION
More informationSeries DKS 2"W Low Profile LED Surface Mount
2"W FEATURES & SPECIFICATIONS INTENDED USE Full body micro silhouette makes a bold statement with a minimal design in brushed nickel powder coated finish (consult factory for other finishes). Scaled to
More informationCustomer service: or Upper mounting ring. Canopy
Components included: Upper mounting ring Canopy Fixture base Fluorescent - 2 x 42 W 4-pin compact fluorescent lamps required (not included). Lutron recommends GE, Sylvania, or Philips lamps that are certified
More informationOne Circuit Trac System TRAC SECTION, JOINERS & FEEDS T Series
Project: Fixture Type: Location: Contact/Phone: PRODUCT DESCRIPTION DIMENSIONS Low-Profile, single-circuit trac sections for surface or pendant mounting. I-beam cross section provides added strength and
More informationLED IMPORTANT SAFETY INSTRUCTIONS
U02301 Rev. B Page 1 of 8 U02301 Rev. B Page 2 of 8 IBG LED HIGHBAY INSTALLATION INSTRUCTIONS WARNING: Please read all important safety instructions prior to installation of this product. A) Identification
More informationA B C D E F. Tools Required (supplied by others)
Page 1 of 17 Parts List Below Deck Automatic Retractable Security Cover Kit (1) Tube End Bearing Plate (A) (1) Rope Reel and Cover Drum Motor Assembly (B) (1) Cover Drum (1) Pulley Support Channel (2)
More informationLED IMPORTANT SAFETY INSTRUCTIONS
LED IMPORTANT SAFETY INSTRUCTIONS READ AND FOLLOW ALL SAFETY INSTRUCTIONS! SAVE THESE INSTRUCTIONS AND DELIVER TO OWNER AFTER INSTALLATION To reduce the risk of death, personal injury or property damage
More informationLumeLEX 2084 SERIES INSTALLATION INSTRUCTIONS THIS SHEET CONTAINS IMPORTANT SAFETY INSTRUCTIONS. SAVE THESE INSTRUCTIONS.
LumeLEX 2084 SERIES INSTALLATION INSTRUCTIONS Important THIS SHEET CONTAINS IMPORTANT SAFETY INSTRUCTIONS. SAVE THESE INSTRUCTIONS. Warning This product must be installed in accordance with National Electrical
More informationNOTICE TO DEALER AND VEHICLE OWNER
921323300 *132330BAG1* 132330BAG1 2009-17 Dodge 2wd 1500 4 Lift Kit Thank you for choosing Rough Country for all your suspension needs. Rough Country recommends a certified technician install this system.
More informationFOR SIT-STAND WORKSTATION
INSTALLATION MANUAL FOR SIT-STAND WORKSTATION Weight Capacity: 6.5-24.5 lbs. 6017180 Rev. B Contents Tools Required / Supplied Part Kits / Warnings/Disclaimers...2 Base Installation Clamp Mount Base Location...3
More informationFIXTURE INSTALLATION GUIDE Model T21T (Low Voltage Pendant Set 120V)
FIXTURE INSTALLATION GUIDE Model T21T (Low Voltage Pendant Set 120V) 21T, Rev.4 6-13 IMPORTANT: Before proceeding, retrieve the GLASS SHADE INSTALLATION GUIDE, which is included with the pendant cord set
More informationInstallation Instructions COMPETITION/PLUS SHIFTER Ford Mustang MT82 6-Speed Manual Transmission Catalog#
Installation Instructions COMPETITION/PLUS SHIFTER 2015-2017 Ford Mustang MT82 6-Speed Manual Transmission Catalog# 3916037 Rev. 00 WORK SAFELY! For maximum safety, perform this installation on a clean,
More informationINSTALLATION INSTRUCTIONS WHITE / SINGLE COLOR 24V LED TAPE
LLI-L1.5W LLI-L2.2W LLI-L2.5W LLI-L3.5W LLI-L4.4W LLI-LHE3.5W LLI-LHE4.4W LLI-LHE5.9W LLI-LTP2.5W LLI-LTP5.0W LLI-LSE3.0W LLI-LWF5.5W LLI-LC4.4W **DANGER: Prior to installation, disconnect power at the
More informationWARNING. Important Notice
CAL (Color AquaLuminator ) Light and Return Water Flow for Above Ground Pools Owners Manual IMPORTANT SAFETY INSTRUCTIONS READ AND FOLLOW ALL INSTRUCTIONS SAVE THESE INSTRUCTIONS Table of Contents SECTION
More informationLOOP 65 Up 35 Dn LS1-A. Luminaire LOOP - 65 UP 35 DN LED (LS1-A) Type. Project. Product. Notes. Performance Summary OPTIONS
T F W 604.549.9379 604.549.9555 fluxwerx.com LOOP Specification Data LOOP - 65 UP 35 DN LED () Type Project Product Notes 65 Up I 35 Down A B C D Light (lm) 2500 3050 3750 4900 Energy (W) 19 23 29 38 Efficacy
More informationCirca Ambient Interior Luminaire
IMPORTANT SAFETY INSTRUCTIONS 1. Read carefully before installing fixture. Retain for future reference. To prevent electrical shock, turn off electricity at fuse box before proceeding. 2. Failure to follow
More informationSpring Bearing Rocker Replacement Installation [Kit # ] for Elevance Continental-Style Delivery Unit
Spring Bearing Rocker Replacement Installation [Kit # 002-2076-00] for Elevance Continental-Style Delivery Unit Note Use this kit to replace one or more Spring Bearing Rockers in an Elevance Continental-Style
More information2010+ Audi B8 S4/S5 3.0T S-FLO Intake Kit INSTALLATION GUIDE FOR RACING USE ONLY
INSTALLATION GUIDE 2010+ Audi B8 S4/S5 3.0T S-FLO Intake Kit FOR RACING USE ONLY Congratulations on your purchase of the AWE Tuning S-FLO Intake for the 2010+ Audi B8 S4 and B8 S5 3.0T. Exquisite build
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS RH-5900L RH-5900 1 MODEL: LUGARNO RH-5900 RH-5900L REV B Restoration Hardware Faucet Product Size Specification Diagram Recommended Deck Hole Size 1-3/8 Diameter Dimensions are
More informationEMERY SKY SUSPENDED LED LUMINAIRE
EMERY SKY SUSPENDED LED LUMINAIRE IP20 DRY LOCATION 120V- 277V AC SAFETY & WARNINGS 1. READ AND FOLLOW ALL SAFETY INSTRUCTIONS 2. Install in accordance with national and local electrical code regulations.
More information»Product» Safety Warning
C2402, C2602 Installation Instructions 2007-2013 Chevy 1/2 Ton 2wd Pickup 4.5", 6.5" Suspension System Read and understand all instructions and warnings prior to installation of product and operation of
More informationInstallation Manual TWM Performance Shift Boot 2006 and up Honda Civic Si
Page 1 Installation Manual TWM Performance Shift Boot 2006 and up Honda Civic Si Begin the installation by parking on a flat surface, as you may have to engage and disengage the hand brake and shift from
More informationPROFILE 50 Up 50 Dn PF1-E. Luminaire PROFILE - 50 UP 50 DN LaED (PF1-E) Type. Project. Product. Notes. Performance Summary
T F W 604.549.9379 604.549.9555 fluxwerx.com PROFILE Specification Data PROFILE - 50 UP 50 DN LaED () Type Project Product Notes 50 Up I 50 Down A B C D Light (lm) 2350 2900 3500 4450 Energy (W) 19 24
More informationBulletin 1494C Cable Operated Disconnect Switch Kit (600A) Installation Instructions (Cat 1494C- _ Series 2 : 600A)
Bulletin 494C Cable Operated Disconnect Switch Kit (600A) Installation Instructions (Cat 494C- _ Series : 600A) ATTENTION: To prevent electrical shock, disconnect from power source before installing or
More information2016 Wand Handle Repair Instructions & Parts List
2016 Wand Handle Repair Instructions & Parts List Updated 9/11/18 2018 by Crafco, Inc. All Rights Reserved 2016 New Style Wand Assembly - Part Number 52200 This style wand assembly is field serviceable.
More informationLED Decorative Highbay
SAVVANO LED Decorative Highbay WARNINGS This product contains chemicals known to the state of California to cause cancer, birth defects and/or other reproductive harm. Thoroughly wash hands after installing,
More informationAssembly instruction. Pendant Light Toccata GENERAL REMARKS ON SAFETY: Technical data: BOM
GENERAL REMARKS ON SAFETY: Read all of these instructions before installing fixtures. Keep all of the instructions for future reference. Turn off power before installing fixture. Installation is to be
More informationThe lever must be placed at the lower position, when the track head is intended to be use in a one-circuit track system.
1-CIRCUIT TRACK Single circuit Extruded aluminum body Insulated solid 12-gauge copper Rated for maximum of 2400 watts Visual polarity groove Compatible with most 3-wire systems ET2 ET4 ET6 ET8 ET12 2 FT.
More informationSteeda Bumpsteer Kit (94-04) - Installation Instructions
Steeda Bumpsteer Kit (94-04) - Installation Instructions The below installation instructions work for the following products: Steeda Bumpsteer Kit (94-04) Please read through the instructions carefully
More information1718 W. Fullerton Ave Chicago, IL Tel: Fax:
07 Edge Lighting. All Rights Reserved. Installation Instructions for Pix Stick Tie Stix Suspension -Light, -Light, -Light and -Light with Power IMPORTANT INFORMATION - This product is suitable for indoor
More information- MK7 Mirror Integration Kit - Installation Instructions
- MK7 Mirror Integration Kit - Thank you for choosing the Double Apex Gentex Mirror Integration kit for your Volkswagen MK7. If you have any questions about the installation please email us at support@dblapex.com.
More informationREAD AND FOLLOW ALL SAFETY INSTRUCTIONS! SAVE THESE INSTRUCTIONS AND DELIVER TO OWNER AFTER INSTALLATION
READ AND FOLLOW ALL SAFETY INSTRUCTIONS! SAVE THESE INSTRUCTIONS AND DELIVER TO OWNER AFTER INSTALLATION To reduce the risk of death, personal injury or property damage from fire, electric shock, falling
More informationPRE-INSTALLATION. INSTALLATION INSTRUCTIONS Front Dodge Ram WD 6" Suspension Lift Kit
2012-2015 Dodge Ram 1500 4WD 6" Suspension Lift Kit PRE-INSTALLATION 35015 2 - Knuckle (Driv/Pass) 2 - Crossmember (Front/Rear) 2 - Differential Bracket (Driv/Pass) 1 - Diff. Brace Bracket (Pass) 2 - Front
More informationLEVELe ELEVATOR INTERIORS WITH LIGHTPLANE INSTALLATION INSTRUCTIONS. STANDARD LEVELe COMPONENTS CEILING COMPONENTS LIGHTPLANE COMPONENTS TOOLS NEEDED
TOOLS NEEDED SUCTION CUP(S) IMPACT DRILL CRESCENT WRENCH #8-18 SQUARE / PHILIPS COMBO DRIVE BIT SQUARE MASKING TAPE PENCIL DRILL BIT EXTENDER 3/8" DRILL BIT TAPE MEASURE CENTER PUNCH LEVEL BRUSH INCLUDED
More informationRound or Square Type Non-IC Adjustable Housing with Toroidal Transformer for Flangeless Trims E3_L_-HANM_ 1.7
Installation Instructions for 90EHMH-ANIC Round or Square Type Non-IC Adjustable Housing with Toroidal Transformer for Flangeless Trims E_L_-HANM_. HALOGEN MR - ROUND/SQUARE FLANGELESS GENERAL PRODUCT
More informationRECESSED TRACK (120V) SPECIFICATIONS
RECESSED TRACK (120V) SPECIFICATIONS GENERAL Recessed track shall be approved by the NEC for flush-mounting into ceiling or any flat surface. Recessed Track shall allow fixtures to be easily focused, switched,
More informationNOTICE TO DEALER AND VEHICLE OWNER
921322300 *1322BAG1* 1322BAG1 2009-17 Dodge 2wd 1500 6 Lift Kit Thank you for choosing Rough Country for all your suspension needs. Rough Country recommends a certified technician install this system.
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS IMPORTANT Before opening your Lights.com fixture, please make sure that you carefully read through these instruction sheets. Consider having your fixture installed by a qualified
More informationNanoLED NXT Cylinder LNRP3 Pendant
NXT NANOLED PENDANT - NANOLED PENDANT - CONDUIT CUTOUT NANOLED GLOW /cylinders Power and beauty are both in play with our sleek architectural cylinders. Concealing the same powerful LED technology of our
More informationInstallation Instructions for SINGLE COLOR 24V LINEAR LED NEON
Installation Instructions for SINGLE COLOR 24V LINEAR LED NEON LLI-N2.9W Prior to installation, please confirm that you have the required system components listed below. LED Neon Flow Extrusions/Lens (Optional)
More informationInstallation Instructions Table of Contents
Installation Instructions Table of Contents Pre- Installation of Garage Storage Lift 2 Layout the Garage Storage Lift 3 Installing the strut Channels 3 Install the Drive Assembly 5 Install the Drive Shaft
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS MODEL: VINTAGE (RH-5700) REV.A Restoration Hardware Faucet Product Size Specification Diagram Recommended Deck Hole Size -/8 Diameter Dimensions are in Inches and Approximation
More informationAmTryke Adult Recumbent Model HP1000 #50-HC-1000
AmTryke Adult Recumbent Model HP1000 #50-HC-1000 TOOLS Needed for Assembly 5 mm Allen Wrench 8 mm Socket or Wrench 10 mm Socket or Wrench 14 mm Socket or Wrench 15 mm Socket or Wrench 22 mm Socket or Adjustable
More informationFIXTURE INSTALLATION GUIDE Model T21T (Low Voltage Pendant Set 120V)
FIXTURE INSTALLATION GUIDE Model T21T (Low Voltage Pendant Set 120V) 21T, Rev.4 6-13 IMPORTANT: Before proceeding, retrieve the GLASS SHADE INSTALLATION GUIDE, which is included with the pendant cord set
More informationInstallation Manual TWM Performance Kia Forte Short Shifter
Installation Manual TWM Performance Kia Forte 2009+ Short Shifter Begin the installation by parking on a flat surface, as you will have to engage and disengage the hand brake and shift from gears to neutral.
More information1996 Aerostar/Ranger/Explorer
Page 1 of 11 Section 03-01B: Engine, 3.0L V-6 IN-VEHICLE SERVICE 1996 Aerostar and Ranger Vehicles Workshop Manual Water Pump SPECIAL SERVICE TOOL(S) REQUIRED Description Tool Number Fan Clutch Holding
More informationParts/Hardware Included. Caution. Tools/Hardware Required. SMS CL V Mounting Plate. SMS CL V Exploded View
Caution ➀ Installer must make sure SMS CL V is positively and securely attached, and appropriate fasteners are used. ➁ Before installing, check to make sure all parts of the mount are there. ➂ Assembly
More informationSTEERING SYSTEM 6 A POWER STEERING
STEERING SYSTEM 6 A 22147 POWER STEERING Table of Contents Page Specifications............................ 6A-1 Torque Specification................... 6A-1 Special Tools............................ 6A-1
More informationIMPORTANT SAFETY INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS READ AND FOLLOW ALL SAFETY INSTRUCTIONS! SAVE THESE INSTRUCTIONS AND DELIVER TO OWNER AFTER INSTALLATION To reduce the risk of death, personal injury or property damage from
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS MODEL: BISTRO (RH-500) REV.A Restoration Hardware Faucet Product Size Specification Diagram Recommended Deck Hole Size -/8 Diameter Dimensions are in Inches and Approximation
More information2015 Mustang Lightbar (All Models) CDC#
2015 Mustang Lightbar (All Models) CDC# 1511-7000-01 Components: 1 CDC Lightbar Note: READ instructions before starting installation!!! CDC Part# Driver side bracket 0511-6001-05 Passenger side bracket
More informationInstallation Manual TWM Performance Short Shifter Nissan 350Z, 370Z Infiniti G35, G37
Installation Manual TWM Performance Short Shifter Nissan 350Z, 370Z Infiniti G35, G37 It is preferable to park on a flat surface, as you will have to engage and disengage the hand brake and shift from
More informationIMPORTANT SAFETY INSTRUCTIONS READ AND FOLLOW ALL INSTRUCTIONS SAVE THESE INSTRUCTIONS
AQUALUMINATOR & AQL LIGHT AND RETURN WATER FLOW FOR ABOVE GROUND SWIMMING POOLS INSTALLATION AND USER'S GUIDE Contents SECTION I. IMPORTANT SAFETY INSTRUCTIONS... 2 SECTION II. LAMP HOUSING INSTALLATION...
More informationZynn Lines - Pendant. AIP in DESCRIPTION FEATURES & BENEFITS SPECIFICATIONS PROJECT DETAILS JOB NAME: TYPE: NOTES:
Zynn Lines - Pendant AIP12116 49 in JOB NAME: TYPE: NOTES: PROJECT DETAILS DESCRIPTION With a cross-section of just 1.25", Zynn Lines suspends slim lines of light in contemporary spaces. Its seamless housing,
More informationINSTALLATION INSTRUCTIONS RECESSED EXTRUSIONS WITH LED TAPE
LLI-XR-CRV LLI-XR-ELF LLI-XR-IFL LLI-XR-IGR LLI-XR-SQF LLI-XR-THF **DANGER: Prior to installation, disconnect power at the source.** Make sure you have all components listed below: LED tape 24VDC Power
More informationOne Circuit Trac System TRAC SECTION, JOINERS & FEEDS T Series
Project: Fixture Type: Location: Contact/Phone: PRODUCT DESCRIPTION DIMENSIONS Low-Profile, single-circuit trac sections for surface or pendant mounting. I-beam cross section provides added strength and
More informationLED Edge-Lit Flat Panels
INSTALLATION GUIDE IMPORTANT SAFETY INFORMATION: Please read all the instructions below before installation. Make sure that the supply voltage corresponds to the rated product voltage. The product is designed
More informationSTEP 1 STEP 2. Disconnect the negative terminal from both batteries.
TROUBLESHOOTING: Please read and understand all installation instructions before proceeding with the installation. If you have questions during the installation of this product, please email H&S Motorsports
More informationWORK INSTRUCTION READ FIRST. IF IN DOUBT
WORK INSTRUCTION PAGE 1 OF 9 FIELD CHANGE INSTRUCTION : TO CHANGE A BACK DOOR AND SIDE LIFT PROCEDURE: Step 1. How to remove and replace the rear door of a canopy. Step 2. How to remove the side lift up
More informationInstallation Manual TWM Performance Short Shifter Cobalt SS/SC, SS/TC, HHR SS, Ion Redline and Saab 9-3
Page 1 Installation Manual TWM Performance Short Shifter Cobalt SS/SC, SS/TC, HHR SS, Ion Redline and Saab 9-3 Please Note: It is preferable to park on a flat surface, as you will have to engage and disengage
More informationHBDBM High Bay Series
HBDBM High Bay Series INSTALLATION INSTRUCTIONS The High Bay Luminaire is ideal for installations with mounting heights over 25 feet. The fixture can be mounted with a hook or pendant with flexible adjustments
More informationFIXTURE INSTALLATION GUIDE Model T21T (Low Voltage Pendant Set 120V)
FIXTURE INSTALLATION GUIDE Model T21T (Low Voltage Pendant Set 120V) 21T, Rev.4 6-13 IMPORTANT: Before proceeding, retrieve the GLASS SHADE INSTALLATION GUIDE, which is included with the pendant cord set
More information