1Unpack fixture. Suspensions/canopies are ordered and

Transcription

1 DO NOT REMOVE THE LED ASSEMBLY. THIS WILL VOID THE WARRANTY. Call Zumtobel at questions. Fixture is intended installation in accordance with bee servicing. Retain these instructions 2Determine spacing mounting points. The supplied Starter Feed contains pre-wired (5) 14-gauge SJT cord. For dimming applications additional (2) 18-gauge SJT cord is supplied. 15A max. rated, in single circuit with three switch legs. It is not intended use with three phase installation wiring conditions. READ ENTIRE INSTRUCTIONS BEFORE STARTING INSTALLATION 1Unpack fixture. Suspensions/canopies are ordered and packaged separately. JUNCTION BOX The unused (4) conductors EL1, EL2, EN1, EN2 are terminated (along with the line voltage conductors) at the end of the run. 14/5 CORD STARTER FEED TRUNKING EL1 EL2 L1 L2 L3 GND EN1 EN2 N D1 D2 L1 SECTION SWITCHED L2 SECTION SWITCHED L3 SECTION EM WALL SWITCHES EL1 NOT USED EN1 NOT USED L1 SWITCHED 4A MAX. Ground L3 L2 L1 Neutral L2 SWITCHED 4A MAX D1 D2 L3 UNSWITCHED 4A MAX EL2 NOT USED EN2 NOT USED L1 SWITCHED HOT N NEUTRAL L2 SWITCHED HOT D1 DIMMIING L3 UNSWITCHED HOT EM D2 DIMMING GND GROUND NOTE: CONSULT WITH FACTORY FOR USE OF ADDITIONAL SWITCHED CIRCUIT Part # D00471CI Date 05/04/17 Page 1 of 11 specification sheets or other inmation about our

2 DO NOT REMOVE THE LED ASSEMBLY. THIS WILL VOID THE WARRANTY. Call Zumtobel at questions. Fixture is intended installation in accordance with bee servicing. Retain these instructions Finished suspension length will be reduced by maximum of 2' 6" depending on location of first and last aircraft cable. Max. 2' 6" Min. 4" 1' 1 1/2" Max. 66 lbs. Max. 66 lbs. Max. 8' Max. 8' Max. 2' 6" Min. 4" Max. 66 lbs. TECTON LED Starter Feed (supplied standard with TECTON LED Individual) 3Prepare ceiling/wall junction box and suspension installation using method(s) below that apply to your installation. All mounting points must be in a straight line. J-boxes must be mounted perpendicular to fixture center line as shown. Fixture Centerline Mount J-box perpendicular to fixture centerline Mounting Point a. Cable, Surface Mount Install junction box (feed or non-feed) 3/16" above the finished ceiling/wall surface. Trunking weight is approximately 1.2 lb/ft. (actual weight depends on optic used; please refer to individual optic spec sheets details) Not to Scale 4" Square Junction Box RCP View Not to Scale b. Cable Mount Hang cable-mounted suspension. Screw cross bar bracket to junction box. Insert cable into keyhole in cross bar bracket. c. Cable Mount 1/4-20 mounting: Secure crossbar with stud at least 1/2 below ceiling tile. Make sure all mounting points, junction boxes and canopies are in a straight line. Standby battery pack fixtures need separate junction box(es) and suspensions. Part # D00471CI Date 05/04/17 Page 2 of 11 specification sheets or other inmation about our

3 DO NOT REMOVE THE LED ASSEMBLY. THIS WILL VOID THE WARRANTY. Call Zumtobel at questions. Fixture is intended installation in accordance with bee servicing. Retain these instructions T-bar Mounted with Power Feed J-box Mounted with Power Feed Backing Nut BACKING NUT LOCK WASHER Lock Washer 1/4-20 1/4"-20 CABLE Cable COUPLER Coupler 4"x 4"x 2 1/8" J-box 4"X4"X2 1/8" J-BOX installation of crossbar (BY OTHERS) bracket (REGRESSED with 3/16") 4.77" mounting CEILING center (By Others) Ceiling (Regressed 3/16") BRACKET Crossbar Bracket 5 Sq. In. Canopy 5 SQ.IN CANOPY T-bar Support Clip Secure to Structure (By Others) 15/16" Tee = IDS 9/16" Tee = IDS9 T-BAR SUPPORT CLIP SECURE TO STRUCTURE (BY OTHERS*) 9/16" Slot Grid = IDS95 (2) J-box Support Clips & Fasteners (By Others) Caddy #ATS4I (2) J-BOX SUPPORT CLIP& FASTENERS (BY OTHERS*) CADDY # ATS4I NOTE: FITS 15/16 & 9/16 TEE BAR AND 9/16 SLOT GRID Note: Fits 15/16 & 9/16 T-bar and 9/16 Slot Grid Screws For Cover SCREWS FOR COVER J-box Cover J-BOX COVER Ground Screw 8-32 x 1/4" & Ground Wire GROUND SCREW 8-32 x 1/4" & GROUND WIRE 4"x 4"X4"X2 4"x 1/8" 2 1/8" TJ-BOX TJ-box (6) KO (6) (2) 1/2" 7/8" KO KO (2) 7/8" KO 1/16" AIRCRAFT Aircraft CABLE Cable Surface Mounted with Power Feed * CADDY CLIP NUMBERS 15/16" T = IDS 9/16" T = IDS9 9/16" SLOT GRID = IDS95 Cord (From Feed Connector) CORD (FROM FEED CONNECTOR) Cable Adjuster & TECTON & Mounting MOUNTING CLIP Clip 4" Sq. J-box (by others) Lock Washer LOCK WASHER 1/4-20 Cable Coupler 1/4"-20 CABLE COUPLER 5 SQ.IN CANOPY (5W SHOWN) 1/16" AIRCRAFT Aircraft CABLE Cable Cable Adjuster & TECTON Mounting Clip & TECTON MOUNTING CLIP 5 Sq. In. Canopy Cord CORD (FROM FEED CONNECTOR) (From Feed Connector) Wall Cords Wall Mounting Bracket WALL MOUNTING BRACKET Trunking TRUNKING Screws 8-32 Canopy Part # D00471CI Date 05/04/17 Page 3 of 11 specification sheets or other inmation about our

4 DO NOT REMOVE THE LED ASSEMBLY. THIS WILL VOID THE WARRANTY. Call Zumtobel at questions. Fixture is intended installation in accordance with bee servicing. Retain these instructions J-box Mounted Non-Power Feed 5" Canopy Backing Nut BACKING NUT 4"x 4"x 2 1/8" J-box (By Others) 4"X4"X2 1/8" J-BOX (BY OTHERS) Ceiling Crossbar Bracket CEILING BRACKET LOCK WASHER 1/4-20 Fastener Non-Power Feed 2 Canopy 2.5 SQ.IN CANOPY 1/4"-20 CABLE COUPLER Lock Washer 1/16" LOCK AIRCRAFT CABLE WASHER 2.5 SQ.IN CANOPY 2 Sq. In. Canopy 1/4-20 1/4"-20 CABLE Cable COUPLER Coupler 1/16" Aircraft Cable 1/16" AIRCRAFT CABLE 1/4-20 Fastener Non-Power Feed 5 Canopy Lock Washer LOCK WASHER 5 Sq. In. Canopy 5 SQ.IN CANOPY 1/4"-20 CABLE COUPLER 1/4-20 Cable Coupler LOCK 1/16" AIRCRAFT CABLE 1/16" WASHER Aircraft Cable LOCK WASHER Lock Washer 5 Sq. In. Canopy 5 SQ.IN CANOPY 1/4-20 1/4"-20 CABLE Cable COUPLER Coupler 1/16" AIRCRAFT Aircraft CABLE Cable Cable Adjuster & TECTON Mounting Clip & TECTON MOUNTING CLIP & TECTON MOUNTING CLIP Cable Adjuster & TECTON Mounting Clip & TECTON MOUNTING CLIP Cable Adjuster & TECTON Mounting Clip & TECTON MOUNTING CLIP CA & T S2 S2 S5 S5 Part # D00471CI Date 05/04/17 Page 4 of 11 specification sheets or other inmation about our

5 DO NOT REMOVE THE LED ASSEMBLY. THIS WILL VOID THE WARRANTY. Call Zumtobel at questions. 4Attach trunking to suspensions Fixture is intended installation in accordance with bee servicing. Retain these instructions a. Cable Mount Snap brackets at the end of the cable to the top of the trunking. Adjust aircraft cable suspension length by pressing the spring-loaded connector and sliding cable to desired length. Position of cable bracket is adjustable along the length of the trunking. b. Surface Mount Attach mounting clips (supplied) to ceiling structure with #10 pan-head screw and washer (by others). 66 lbs. Part # D00471CI Date 05/04/17 Page 5 of 11 specification sheets or other inmation about our

6 DO NOT REMOVE THE LED ASSEMBLY. THIS WILL VOID THE WARRANTY. Call Zumtobel at questions. Fixture is intended installation in accordance with bee servicing. Retain these instructions 1/16 9/16 or 15/16 25 lbs. c. Surface Mount T-bar Attach caddy clip to T-bar and with nut driver (by others) twist caddy clip 90 to securely lock in place. 90 Part # D00471CI Date 05/04/17 Page 6 of 11 specification sheets or other inmation about our

7 DO NOT REMOVE THE LED ASSEMBLY. THIS WILL VOID THE WARRANTY. Call Zumtobel at questions. Fixture is intended installation in accordance with bee servicing. Retain these instructions 5Attach trunking sections to each other continuous runs by pressing firmly until the CLIX sound is heard. Make sure to orient the trunkings correctly as shown. Trunkings are shipped prewired mechanical and electrical connection and grounding. 6Attach Starter feed module to trunking unit by pushing firmly until CLIX sound is heard. Make electrical connections from supplied power cord to ceiling. TECTON LED Starter Feed Part # D00471CI Date 05/04/17 Page 7 of 11 specification sheets or other inmation about our

8 DO NOT REMOVE THE LED ASSEMBLY. THIS WILL VOID THE WARRANTY. Call Zumtobel at questions. Fixture is intended installation in accordance with bee servicing. Retain these instructions 7Complete the run. THIS IS A VERY IMPORTANT STEP. a. End Cap Terminate the wiring using supplied busbar terminator cover as shown below. Insert the cover through the open end of the trunking, making sure the orientation is correct. Push the cover in until you hear a click to indicate positive engagement. Finally complete the run by inserting supplied end cap. Part # D00471CI Date 05/04/17 Page 8 of 11 specification sheets or other inmation about our

9 DO NOT REMOVE THE LED ASSEMBLY. THIS WILL VOID THE WARRANTY. Call Zumtobel at questions. Fixture is intended installation in accordance with bee servicing. Retain these instructions OR b. Cut the trunking as desired using supplied cutting aid (ordered separately). Brush out the shavings and terminate the wiring using supplied end cap ordered separately a OR c. End the run with an empty trunking by cutting it to desired length and completing with an end cap. TECTON LED Empty Trunking 6 1/4" 2' 9" Part # D00471CI Date 05/04/17 Page 9 of 11 specification sheets or other inmation about our

10 DO NOT REMOVE THE LED ASSEMBLY. THIS WILL VOID THE WARRANTY. Call Zumtobel at questions. 8Make electrical connections using supplied power cord. Attach canopy ground wire to a suitable point in the junction box, per NEC and local codes. Fixture is intended installation in accordance with bee servicing. Retain these instructions 9Slide canopy to cover junction box. Repeat all canopies. J-BOX MOUNTED WITH NON POWER FEED Lock LOCK Washer WASHER 1/4"-20 Cable Coupler 5 Sq. In. Canopy 5 SQ.IN CANOPY 1/4"-20 CABLE COUPLER 1/16" AIRCRAFT Aircraft CABLE Cable Secure power cord to 10 aircraft cable with wire ties provided. Wire ties provide strain relief. Cable Kit CABLE KIT BELOW INTRUCTIONS FOR FIELD CHANGE REQUIREMENTS ONLY. INDIVIDUAL FIXTURES ARE SUPPLIED ASSEMBLED. Attach batten to installed trunking. Select switchable leg by choosing L1, L2 or L3. Press lever on movable 11 contact to disengage as shown and slide it up or down to desired location. When the indicator lines up with L1, L2 or L3 and clicks into place, release to re-engage lever. Note: Plan loading of 4A each circuit. (80% of maximum rating). Maximum 12A total each feed point. Part # D00471CI Date 05/04/17 Page 10 of 11 specification sheets or other inmation about our

11 volume) supplied by others. Canopies and suspensions are ordered separately. Junction boxes should be installed regressed 3/16" into sheetrock ceiling. For T-bar ceilings use caddy clips by others. Please refer to the approved DO NOT REMOVE THE LED ASSEMBLY. THIS WILL VOID THE WARRANTY. Call Zumtobel at questions 12. For corners, make electrical connections as described on page Mate the corners to the trunking by pressing firmly until a clicking sound is heard. Part # D00471CI Date 05/04/17 Page 11 of 11 specification sheets or other inmation about our products, Page 3 please go to