LED Decorative Highbay

Transcription

1 SAVVANO LED Decorative Highbay WARNINGS This product contains chemicals known to the state of California to cause cancer, birth defects and/or other reproductive harm. Thoroughly wash hands after installing, handling, cleaning, or otherwise touching this product. Contact Hubbell Lighting, Inc. for information and direction before relamping or replacing this light fixture. Disconnect power before installing or servicing. Install, operate and maintain to meet all applicable codes. Protect all wiring connections with approved insulators (by others.) Selected fixture voltage must match supply line voltage. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE Upon receipt of this fixture, thoroughly inspect it for any damage. If any is found, the carrier should be notified and held accountable.

2 FIXTURE RECEIVING: For shipping purposes, the fixture will come in multiple boxes. FIXTURE RECEIVING: The upper assembly will For be shipping packaged purposes, the fixture separately will come in multiple from boxes. the reflector assembly and, if optioned, the lens assembly. The upper assembly will be packaged separately from the reflector See instructions on pages 3 & 4 for initial fixture assembly. assembly and, if optioned, the lens assembly. See instructions on pages 3 & 4 for initial fixture assembly. UPPER REFLECTOR LENS RING/ HARDWARE OPTIONAL EQUIPMENT LENS FIGURE 1 FIXURE BOXING REFLECTOR INSTALLATION: MH / MM / ML MODELS (See Figure 2B) 1. Reflector can be installed on the ground or while fixture is hanging. If installing on the ground, it is best to place fixture upside down. 2. Locate the four (4) threaded studs protruding from the bottom of the glass lens ring and align them with the holes in the reflector collar. 3. Insert the studs through the holes and thread on the provided hexagonal nut. Using a 5/16 hex driver, tighten hexagonal nut to 10 in-lbs. LX/ LH MODELS (See Figure 2A) 4. Reflector can be installed on the ground or while fixture is hanging. If installing on the ground, it is best of place fixture upside down. 5. Locate the four (4) threaded studs protruding from the bottom of the glass lens ring and align them with the holes in the reflector collar. 6. Insert the studs through the holes and install the provided hexagonal standoffs along with lock washers. Using a 1/4 hex driver, tighten the whexagonal standoffs to 10 in-lbs.

3 SAV-SAVVANO DECORATIVE FIXTURE REFLECTOR INSTALLATION: MH / MM / ML MODELS (See Figure 2B) 1. Reflector can be installed on the ground or while fixture is hanging. If installing on the ground, it is best to place fixture upside down. 2. Locate the four (4) threaded studs protruding from the bottom of the glass lens ring and align them with the holes in the reflector collar. 3. Insert the studs through the holes and thread on the provided hexagonal nut. Using a 5/16" hex driver, tighten hexagonal nut to 10 in-lbs. LX/ LH MODELS (See Figure 2A) 4. Reflector can be installed on the ground or while fixture is hanging. If installing on the ground, it is best of place fixture upside down. 5. Locate the four (4) threaded studs protruding from the bottom of the glass lens ring and align them with the holes in the reflector collar. 6. Insert the studs through the holes and install the provided hexagonal standoffs along with lock washers. Using a 1/4" hex driver, tighten the hexagonal standoffs to 10 in-lbs. LOCK WASHER 4 PLACES HEXAGONAL STANDOFF 4 PLACES REFLECTOR COLLAR THREADED STUD 4 PLACES FIGURE 2A REFLECTOR COLLAR MOUNTING LX / LH THREADED STUD 4 PLACES REFLECTOR COLLAR Industrial Lighting HEXAGONAL NUT 4 PLACES FIGURE 2B REFLECTOR COLLAR MOUNTING MH / MM / ML A subsidiary of Hubbell Incorporated Revision A 701 Millennium Drive Greenville, SC Page 3 Phone (864)

4 LENS INSTALLATION (If Optioned): 1. Once the reflector has been mounted to the upper assembly, then the lens can be installed. 2. Seat the lens into LENS INSTALLATION the bottom (If Optioned): of the reflector. 1. Once the reflector has been mounted to the upper assembly, 3. Orient Lens Mounting then the lens Ring can be installed. such that short leg of the cross section is on top and install over the lip of the reflector 2. Seat the lens into the bottom of the reflector and lens. See 3. Figure Orient Lens 3B. Mounting Ring such that short leg of the cross section is on top and install over the lip of the reflector and 4. While manually lens. holding See Figure 3B. the ring together, install screw through bracket holes and thread on hexagonal nut and 4. While manually holding the ring together, install screw through tighten till snug. bracket holes and thread on hexagonal nut and tighten till snug. REFLECTOR LENS (OPTIONAL) LENS MOUNTING RING (OPTIONAL) HEXAGONAL NUT SCREW FIGURE 3A LENS MOUNTING REFLECTOR LENS FIGURE 3B LENS MOUNTING RING SEE NOTE 3 GENERAL INFORMATION All 12 (304.8 mm) minimum supply wire outside of conduit. Fixture mounting hub conduit threads are 3/4-14 NPS. PENDANT MOUNTING: (See Figures 4A & 4B) 1. Remove the Wire Access Cover and Mounting Hub Assembly from the fixture top by removing the (3) ¼ screws using a 3/8 Hex driver or flathead screwdriver. See Figure 4B. 2. The Mounting Hub Assembly should be installed on the already-hanging pendant conduit. See Figure 4A. The conduit and conduit lock nut should be securely fastened into the Mounting Hub at this time. 3. Thread the Set Screw into the Mounting Hub to lock into the Conduit using a 1/8 Allenhead driver. See Figure 4A. 4. Loosely thread the Hub Lock Nut onto the Mounting Hub so that there is play between the Hub Plate and Mounting Hub. See Figure 4A. 5. Feed electrical supply wire through the conduit and out the bottom of the Mounting Hub, with 12 of extra wire protruding from the bottom. 6. Hang fixture so that the Mounting Hub sets into the Top Plate and the hub flanges engage the inside of the top plate. Align holes in the Hub Plate with the holes in the Top Plate and insert and tighten the (2) ¼ screws to secure the position of the Hub. Tighten the Hub Lock Nut to the lock the plate and hub in place.

5 7. Pull the excess fixture and incoming wiring out through the Wire Access Cover hole and make the wiring connections. See appropriate WIRING SCHEMATIC for reference. Incoming power to be connected to the white and black wires. Ensure incoming wiring ground wire connected to fixture ground connector. See warnings above about wire connections. Dress wires as needed. 8. Once all wiring connections are made, place all wiring back inside wire box under the Access Cover and replace cover with (1) ¼ screw. SAV-SAVVANO DECORATIVE FIXTURE GENERAL INFORMATION All 12 (304.8 mm) minimum supply wire outside of conduit. Fixture mounting hub conduit threads are 3/4-14 NPS. PENDANT MOUNTING: (See Figures 4A & 4B) 1. Remove the Wire Access Cover and Mounting Hub Assembly from the fixture top by removing the (3) 1/4" screws using a 3/8" Hex driver or flathead screwdriver. See Figure 4B. 2. The Mounting Hub Assembly should be installed on the already-hanging pendant conduit. See Figure 4A. The conduit and conduit lock nut should be securely fastened into the Mounting Hub at this time. 3. Thread the Set Screw into the Mounting Hub to lock into the Conduit using a 1/8" Allenhead driver. See Figure 4A. 4. Loosely thread the Hub Lock Nut onto the Mounting Hub so that there is play between the Hub Plate and Mounting Hub. See Figure 4A 5. Feed electrical supply wire through the conduit and out the bottom of the Mounting Hub, with 12" of extra wire protruding from the bottom. 6. Hang fixture so that the Mounting Hub sets into the Top Plate and the hub flanges engage the inside of the top plate. Align holes in the Hub Plate with the holes in the Top Plate and insert and tighten the (2) 1/4" screws to secure the position of the Hub. Tighten the Hub Lock Nut to the lock the plate and hub in place. 7. Pull the excess fixture and incoming wiring out through the Wire Access Cover hole and make the wiring connections. See appropriate WIRING SCHEMATIC for reference. Incoming power to be connected to the white and black wires. Ensure incoming wiring ground wire connected to fixture ground connector. See warnings above about wire connections. Dress wires as needed. 8. Once all wiring connections are made, place all wiring back inside wire box under the Access Cover and replace cover with (1) 1/4" screw. CONDUIT FOR PENDENT HANGING CONDUIT LOCK NUT HUB LOCK NUT HUB PLATE NOTE: SET SCREW TO BE THREADED BELOW OUTER THREADS OF HUB FOR LOCK NUT TO BE ABLE TO THREAD MOUNTING HUB FIGURE 4A PENDANT-MOUNTING HUB SCREW 2x 1/4-20X.50 3/8" BUSHING WIRE ACCESS COVER SCREW 1/4-20X.50 FIXTURE TOP PLATE MOUNTING HUB Industrial Lighting FIGURE 4B PENDENT MOUNT Hubbell Lighting, Inc. Doc. No A subsidiary of Hubbell Incorporated Revision A 701 Millennium Drive Greenville, SC Page 5 Phone (864)

6 GENERAL INFORMATION All 12 (304.8 mm) minimum supply wire outside of conduit. Fixture mounting hub conduit threads are 3/4-14 NPS. PENDANT MOUNTING: (See Figures 4A & 4B) 1. Insert end of Cord (B) through Hook (A). Supply Cord is to be rated for a minimum of 90 degc 16/3 SOW-A. 2. Remove Wire Access Cover after removing ¼ retaining screw. 3. Loosen Hub Locknut and remove Hub and Hub Plate by removing (2) ¼ Screws. 4. Insert rubber Bushing (E) between Washers (G) and place inside Mounting Hub. Place Cord Grip (C) with cone shape up on top of washer (G). 5. Thread Hook Lock Nut (D) to within 1/8 of the top of the hook threads. 6. Insert Cord (B) through cord grip and washers and through the mounting hub. 7. Thread the Hook into the ¾ NPS hole in the Mounting Hub down to the lock nut. Use pliers and wrench to tighten the Hook Lock Nut (D) to lock the hook in place. CAUTION: Do not twist the Hook by using a screwdriver blade - too much force could break the Hook. 8. Using a 1/8 Allen head SAV-SAVVANO driver, tighten DECORATIVE Set Screw FIXTURE in Mounting Hub to secure Hook from loosening. 9. GENERAL Place INFORMATION: Hub into Top Plate of Housing so that the Hub flanges engage inside of the plate. Align holes in Hub Plate with All 12 (304.8 mm) minimum supply wire outside of conduit. holes in Top Plate and insert and tighten ¼ screws to secure position A Fixture mounting hub conduit threads are 3/4-14 NPS. of Hub. Tighten the Hub Locknut to lock Plate and Hub in place. HOOK/LOOP MOUNTING: (See Figures 5A, 5B & 5C) HOOK 10. Pull the excess fixture and incoming wiring out through the Wire Access CLOSURE 1. Insert end of Cord (B) through Hook (A). Supply Cord is to be rated for a minimum BRACKET/SCREW Cover hole and make the wiring connections. of 90 degc 16/3 SOW-A. See appropriate WIRING SCHEMATIC for reference. Incoming power to be connected to the white and black wires. Ensure 2. Remove Wire Access Cover after removing 1/4" retaining screw 3. Loosen incoming Hub Locknut wiring and remove ground Hub and Hub wire Plate by removing connected (2) 1/4" Screws. to fixture B ground connector. See warnings above about wire connections. Dress 4. Insert rubber Bushing (E) between Washers (G) and place inside Mounting Hub. Place wires Cord Grip as (C) needed. with cone shape up on top of washer (G). 5. Thread Hook Lock Nut (D) to within 1/8" of the top of the hook threads Insert Once Cord all (B) through wiring cord grip connections and washers and through are the made, mounting hub. place all wiring back inside wire box under the Access Cover and replace cover with 7. Thread the Hook into the ¾ NPS hole in the Mounting Hub down to the lock nut. (1) ¼ screw. Use pliers and wrench to tighten the Hook Lock Nut (D) to lock the hook in place. D 12. CAUTION: Attach Do not Hook twist the Closure Hook by using Bracket a screwdriver onto blade - too end much force of Hook with screw provided. After fixture is hung, the Closure Bracket should be could break the Hook. C 8. Using secured a 1/8 Allenhead across driver, the tighten Hook Set Screw opening Mounting Hub to secure prevent Hook disengagement. from loosening. G UCTIONS 9. Place Hub into Top Plate of Housing so that the Hub flanges engage GENERAL inside of the INFORMATION: plate. Align holes in Hub Plate with holes in Top Plate and insert and tighten 1/4" All 12 (304.8 mm) minimum supply wire outside of conduit. E A screws to secure position of Hub.Tighten the Hub Locknut to lock Plate and Hub in place. Fixture mounting hub conduit threads are 3/4-14 NPS. 10. Pull the excess fixture and incoming wiring out through the Wire Access Cover hole HOOK/LOOP MOUNTING: G and make the wiring connections. See appropriate WIRING SCHEMATIC for (See Figures 5A, 5B & 5C) FIGURE 5A reference. Incoming power to be connected to the white and black 1. wires. Insert Ensure end of Cord (B) through HOOK Hook LOOP (A). Supply Cord is to be rated for a minimum incoming wiring ground wire connected to fixture ground connector. See of warnings 90 degc 16/3 SOW-A. above about wire connections. Dress wires as needed. 2. Remove Wire Access Cover after removing 1/4" retaining screw 11. Once all wiring connections are made, place all wiring back inside wire 3. box Loosen under Hub Locknut and remove Hub and Hub Plate by removing (2) 1/4" Screws. the Access Cover and replace cover with (1) 1/4" screw. 4. Insert rubber Bushing (E) between Washers (G) and place inside Mounting Hub. 12. Attach Hook Closure Bracket onto end of Hook with screw provided. After Place fixture Cord is Grip (C) with cone shape up on top of washer 3/8" BUSHING (G). hung, the Closure Bracket should be secured across the Hook opening 5. to Thread prevent Hook Lock Nut (D) to within 1/8" of the top of the hook threads. WIRE ACCESS COVER disengagement. 6. Insert Cord (B) through cord grip and washers and through the mounting hub. 7. Thread the Hook into the ¾ NPS hole in the Mounting Hub down SCREW to the lock nut. HUB LOCK NUT Use pliers and wrench to tighten the Hook Lock Nut (D) to lock the 1/4-20X.50 hook in place. HUB PLATE SCREW CAUTION: Do not twist the Hook by using a screwdriver blade - too much force 2x 1/4-20X.50 could break the Hook. 8. Using a 1/8 Allenhead driver, tighten Set Screw in Mounting Hub to secure Hook FIXTURE from loosening. TOP PLATE 9. Place Hub into Top Plate of Housing so that the Hub flanges engage inside of the plate. Align holes in Hub Plate with holes in Top Plate and insert and tighten 1/4" screws to secure position of Hub.Tighten the Hub Locknut to lock Plate and Hub in place. MOUNTING 10. Pull the excess fixture and incoming wiring out through the Wire Access Cover hole HUB and make the wiring connections. See appropriate WIRING SCHEMATIC for NOTE: SET SCREW TO BE THREADED BELOW OUTER THREADS OF HUB FOR LOCK reference. Incoming power to be connected to the white and black wires. Ensure incoming wiring ground wire connected to fixture ground connector. See warnings above about wire connections. Dress wires as needed. NUT TO BE ABLE TO THREAD 11. Once all wiring connections are made, place all wiring back inside wire box under the Access Cover and replace cover with (1) 1/4" screw. FIGURE 5B 12. Attach Hook Closure Bracket onto end of Hook with screw provided. After fixture is MOUNTING HUB hung, the Closure Bracket should be secured across the Hook opening to prevent disengagement. HUB LOCK NUT HUB PLATE SCREW 2x 1/4-20X.50 B D C G E G FIGURE 5A HOOK LOOP HOOK CLOSURE BRACKET/SCREW 3/8" BUSHING WIRE ACCESS COVER SCREW 1/4-20X.50 Industrial Lighting FIGURE 5C HOOK LOOP FIXTURE TOP PLATE MOUNTING Hubbell Lighting, Inc. HUB Doc. No A subsidiary of Hubbell Incorporated Revision A 701 Millennium Drive Greenville, SC NOTE: SET Page SCREW 6 TO BE Phone (864) THREADED BELOW OUTER THREADS OF HUB FOR LOCK NUT TO BE ABLE TO THREAD FIGURE 5B MOUNTING HUB

7 WIRE GUARD INSTALLATION (If Optioned): 1. With the screws removed, spread the guard apart slightly and fit it around the lens ring already attached to the reflector. 2. The guard should mount around the lens ring such that the ring fits between the top two circular rings. 3. Insert the screws (2x) through the mounting holes and thread on the hexagonal kepis nuts (2x). Tighten the nuts till the guard is clamped around the lens ring. WIRE GUARD INSTALLATION (If Optioned): 1. With the screws removed, spread the guard apart slightly and fit it around the lens ring already attached to the reflector. 2. The guard should mount around the lens ring such that the ring fits between the top two circular rings. 3. Insert the screws (2x) through the mounting holes and thread on the hexagonal kepis nuts (2x). Tighten the nuts till the guard is clamped around the lens ring. FIGURE 6A WIRE GUARD SCREW (2X) KEPIS NUT (2X) WIRE GUARD LX / LH MODELS MH / MM / ML MODELS

8 OCCUPANCY SENSOR INSTALLATION (If Optioned): NOTE: If a wire guard is supplied, the wire guard needs to be installed first (see Page 9, Fig. 7A) before installing sensor on the bracket. Position the guard so the sensor bracket fits through the top two rings of the guard. 1. Position the sensor box (without the tightening ring attached) on top of the bracket and place the threaded shaft through the hole in the bracket. Fasten the tightening ring onto the threads until sensor box is secure. See Fig. 7B. 2. Screw the sensor lens onto the threaded shaft until secure. See Fig. 7C. Mounting Bracket FIGURE 7A WIRE GUARD W/ OCCUPANCY SENSOR FIGURE 7B SENSOR INSTALLATION Mounting Bracket FIGURE 7C SENSOR INSTALLATION WIRE GUARD W/ OCCUPANCY SENSOR

9 LINE DRAWINGS 22 Option Drop (DLR) Lens Conical Drop (CDL) Lens P95/Clear (CLR)/No Lens Option Drop (DLR) Lens Conical Drop (CDL) Lens P95/Clear (CLR)/ No Lens

10 WIRING DIAGRAMS TERMINAL ATTACHED TO WIRE BOX (INSIDE) BROWN OPTION - OCCUPANCY SENSOR DRIVER #1 G R E E N B R O W N B L A C K DRIVER #2 OPTION - FUSING SURGE SUPPRESSOR SEE TERMINATION OPTIONS VIOLET LEADS GRAY LEADS OPTION - OCCUPANCY SENSOR POWERPACK SAV-SAVVANO DECORATIVE FIXTURE RICAL DIAGRAM LH MODELS TERMINAL ATTACHED TO WIRE BOX (INSIDE) LECTRICAL DIAGRAM H / MM / ML MODELS FROM DRIVER #2 FROM DRIVER #2 DIMMING OPTION -W/O OCC. SENSOR: VIOLET AND GRAY LEADS TO BE ROUTED UP THROUGHWIRE BOX WITH,, & LEADS EXITING FIXTURE -W/ OCC. SENSOR: VIOLET AND GRAY LEADS TO BE ATTACHED TO APPROPRIATE CONNECTORS ON SENSOR POWERPACK. VIOLET LEADS GRAY LEADS DIMMING OPTION -W/O OCC. SENSOR: VIOLET AND GRAY LEADS TO BE ROUTED UP THROUGHWIRE BOX WITH,, & LEADS EXITING FIXTURE -W/ OCC. SENSOR: VIOLET AND GRAY LEADS TO BE ATTACHED TO APPROPRIATE CONNECTORS ON SENSOR POWERPACK. DRIVER #1 SEE TERMINATION OPTIONS BROWN LEADS LEADS DIMMING OPTION FROM DRIVER #2 LEADS LEADS FROM DRIVER #2 SAV-SAVVANO DECO INSTALLATION IN ELECTRICAL DIAGRAM LX / LH MODELS OPTION - OCCUPANCY SENSOR POWERPACK OPTION - FUSING B L A C K LEADS LEADS SURGE SUPPRESSOR LEADS LEADS HIL_0355_SAV_IN_17 7/17 LEADS LEADS VIOLET LEADS GRAY LEADS VIOLET AND GRAY LEAD TO BE GROUPED WITH,, & LEADS EXITING FIXTURE WHEN DIMMING OPTION IS UTILIZED A subsidiary of Hubbell Incorporated Revision A 701 Millennium Drive Greenville, SC Page 12 Phone (864) SEE TERMINATION OPTIONS OPTION - FUSING SAV-SAVVANO DECO INSTALLATION IN ELECTRICAL DIAGRAM MH / MM / ML MODELS VIO GR GR WH