INSTALLATION INSTRUCTIONS HYLYTR WALL GRAZER
|
|
- Ariel Perry
- 5 years ago
- Views:
Transcription
1 HYLYTR WALL GRAZER Page 1 of 11 IMPORTANT SAFETY INSTRUCTIONS When installing or using this recessed fixture basic safety precautions should be followed Read ALL INSTRUCTIONS before installing fixture. This fixture is intended for installation in accordance with the National Electric Code and Local and State Codes and must be installed by a licensed electrical contractor. DO NOT INSTALL THIS FIXTURE IN DAMP LOCATIONS. DO NOT INSTALL FIXTURE WITHOUT A MINIMUM 1/2 INCH CLEARANCE ALL AROUND THE FIXTURE. ENSURE CLEARANCE AT TOP OF CHANNEL IS 3 INCHES. THIS FIXTURE IS FOR INSTALLATION IN NON INSULATED CEILINGS ONLY. To prevent electrical shock, turn off electricity at fuse box before installing the fixture. Turn off power and allow fixture to cool down before adjusting position of lamp gimbals. Use AWG#12 wire only for supply to the fixture. CA P E TalkToUs@alwusa com W alwusa com
2 HYLYTR WALL GRAZER RECESSED Page 2 of 11 GRID: TGRID & SLOT 1. DISCONNECT power at fuse box before installation of fixture. 2. Remove lid from power supply assembly and locate powerfeed knockout that connects to building wire. Set parts aside. 3. Locate wall and orient fixture to ensure correct tilt angle (aperture opening to face wall). There is a sticker declaring the wall direction. 4. When placing into GRID ceiling, ensure correct grid dimensions per diagrams to the right. 5. SUPPORT unit to structure via All-Thread Coupler bracket supplied by ALW. 6. If joining multiple sections together, insert joining bracket into middle slot on both connecting sections and proceed to tighten set screw (8-32 set screw should be supplied). 7. Locate building conduit (by others) and connect to power supply and splice power connections within enclosure per submitall drawing electrical callouts. 8. Push wires into enclosure and secure lid onto enclosure using supplied screws. 9. Turn on power ALL-THREAD COUPLER: ALWAYS USE ALL-THREAD COUPLER TO SUPPORT STRUCTURE. UNITS ARE NOT SUPPORTED BY GRID WALL ORIENTATION STICKER DETAILr and ensure correct orientation against wall due to 2º tilt. CA P E TalkToUs@alwusa com W alwusa com
3 HYLYTR WALL GRAZER RECESSED MUD-IN Page 3 of DISCONNECT power before installation to prevent injury and/or harm to product. MUD-FLANGE SUPPORT DETAIL NO METAL FROM MUD-FLANGE SHOULD BE EXPOSED AFTER PLASTER/MUDDING 2. Locate MUD ACCESSORY and ensure correct orientation by locating "WALL SIDE" sticker. 3. Insert mud accessory into opening and align the bottom of mud accessory to be flush with ceiling surface. 4. Secure mud accessory to proper blocking/stud support with SCREWS (by others) or other fasteners as needed. For mud-in application, drywall is in front of "mud wings", tape and putty to edges, no metal should be exposed on drywall. 5. Pull building conduit (by others) through mud accessory. 6. Locate the power supply enclosure on fixture body and remove power supply enclosure lid and set aside for later use. 7. Terminate building conduit to 7/8" KO located on power supply enclosure. Make electrical connections inside enclosure per project submital drawing electrical callouts. Ensure that no wires are pinched. ANCHOR FIXTURE TO MUD-ACCESSORY 8. Re-attach lid and locate DC/DC powercord on opposite side of power supply enclosure. Make electrical connections to fixture body (if not already connected by factory) using color coded connectors. 9. Insert fixture into mud accessory and locate achor points located near the aperture opening. Refer to diagram on right for illustration. 10. Anchor fixture to mud-accessory using supplied screws and L-hex wrench. 11. Power on. CA P E TalkToUs@alwusa com W alwusa com
4 HYLYTR WALL GRAZER RECESSED MUD-IN Page 4 of 11 MUD-FLANGE DETAIL CA P E TalkToUs@alwusa com W alwusa com
5 HYLYTR WALL GRAZER RECESSED PERIMETER Page 5 of 11 Perimeter PERIMETER BRACKET DETAIL 1. DISCONNECT power at fuse box before installing fixture. 2. Remove lid from power supply assembly and locate powerfeed knockout that connects to building wire. Set parts aside. 2. Install aluminum L-extrusion at specified height according to grid diagrams on page 4 to match your grid ceiling. This extrusion is intended to hide uneveness of the wall. 3. Install perimeter bracket at specified height according to grid diagrams on page 4 to match your grid ceiling. Perimeter bracket is indended to support the weight of the fixture and needs to be proprly fastended and anchored to the wall. 4. Slide perimeter all-thread to match the spacing of the perimeter bracket on the wall. 5. If joining multiple sections together, insert joining bracket into middle slot on both connecting sections and proceed to tighten set screw. 6. Raise fixture from below so that sliding all-thread slides through perimeter bracket and secure using 1/4-20 nut. 7. Locate building conduit (by others) and connect to power supply and splice power connections within enclosure per submitall drawing electrical callouts. 8.Push wires into enclosure and secure lid onto power supply enclosure unit using supplied screws. 9. Turn on power. CA P E TalkToUs@alwusa com W alwusa com
6 HYLYTR WALL GRAZER RECESSED PERIMETER Page 6 of 11 PERIMETER DETAIL TGRID CEILING SLOT CEILING CA P E TalkToUs@alwusa com W alwusa com
7 HYLYTR MULTI-GRAZER WALL MOUNT Page 7 of 11 DISCONNECT power at fuse box before installing fixture. Mount Fixture to Wall/Surface 1. The fixture is assembled to recieve power from the LEFT (see diagram) arm's junction box. This junction box is designed to be secured to the side of a stud. 2. The ARM MOUNTING PLATE attaches to the JBOX2 FACE PLATE via screws provided. 3. This ARM MOUNTING PLATE is hidden behind the provided COVER PLATE which is secured via velcro. 4. The RIGHT side arm mounting plate is to be screwed directly into the wall with appropriate backing and support. 5. If not already attached, slide the shroud accessory through the middle slot channel of fixture body and achor shroud using provided adhesive. 6. Endcaps are secured onto fixture using #6-32 set screws. Connecting Building Power to Remoted Power Supply 1. Remove lid from power supply enclosure and place aside. 2. Located building power wires and feed through a conduit (provided by others). Terminate conduit to 7/8" KO located on the power supply enclosure. 3. Splice and connect the power wires to power supply within enclosure per submitall drawing electrical callouts. 4. Make electrical connection to fixture between power supply enlcosure and JOBX2 using provided connectors which are color coded. 5. Double check electrical connections and re-secure lid to power supply enclosure. 6. Power on. POWER THRU-ARM DETAIL ARM DETAIL JBOX2 DIMENSIONS CA P E TalkToUs@alwusa com W alwusa com
8 HYLYTR SHOWCASER SUSPENDED Page 8 of 11 JBOX DETAIL 1. DISCONNECT power at fuse box before installing fixture. 2. The fixture is assembled to recieve power thru the powerfeed canopy. This canopy is designed to mount to a 4" JBOX (supplied by others). 3. Locate suspension cable and bracket (refer to project submital drawings for mounting distances). 4. Install cable suspension hardware to surface (examples of surfaces located on next page). Please note that cable suspension hardware must be supported with proper backing. 5. Locate powerfeed canopy and install canopy bracket to building JBOX. 6. Locate remoted power supply enclosure assembly and connect building conduit (by others) to 7/8" KO after removing lid. 7. Make electrical connections within enclosure according to project submital drawing electrical call outs to building power. 8. Locate powercord on opposite side of the power supply enlosure and run cable to fixture JBOX. 9. Make electrical connections within JBOX according to project submital drawings. Be careful to avoid pinching conductors and possibly damaging product. SHROUD ACCESSORY DETAIL 10. After ensuring proper connections, re-secure power enclosure lid. 11. If not already on, slide appropriate shroud accessory through middle slot of fixture body and achor shrouds using the supplied ahesive. 12. Power on. CANOPY DETAIL CA P E TalkToUs@alwusa com W alwusa com
9 HYLYTR SHOWCASER SUSPENDED (CABLE): Refer to project submitall drawings for specfic mounting spacing points Page 9 of PLAN SUSPENSION POINTS Always refer to project submital drawings for all cut and mounting dimensions. 2. INSTALL BULLET COLLAR TO CEILING sheet metal screws 1/4-20 threaded rods hollow wall anchor bullet collar bullet cable 3. FASTEN BULLET AND ADJUST ceiling Depress tip to adjust height Tighten Bullet with suspension cable CA P E TalkToUs@alwusa com W alwusa com
10 HYLYTR SHOWCASER RECESSED Page 10 of 11 GRID: TGRID & SLOT 1. DISCONNECT power at fuse box before installation of fixture. 2. Remove lid from power supply assembly and locate powerfeed knockout that connects to building wire. Set parts aside. 3. When placing into GRID ceiling, ensure correct grid dimensions per diagrams to the right. 4. SUPPORT unit to structure via All-Thread Coupler bracket supplied by ALW. 5. If joining multiple sections together, insert joining bracket into middle slot on both connecting sections and proceed to tighten set screw (8-32 set screw should be supplied). 6. Locate building conduit (by others) and connect to power supply and splice power connections within enclosure per submitall drawing electrical callouts. 7. Push wires into enclosure and secure lid onto enclosure using supplied screws. 8. Turn on power ALL-THREAD COUPLER: ALWAYS USE ALL-THREAD COUPLER TO SUPPORT STRUCTURE. UNITS ARE NOT SUPPORTED BY GRID WALL ORIENTATION STICKER DETAILr and ensure correct orientation against wall due to 2º tilt. CA P E TalkToUs@alwusa com W alwusa com
11 POWER SUPPLY ENCLOSURE DETAILS POWER SUPPLY ENCLOSURE Page 11 of 11 THE POWER SUPPLY ENCLSOURE IS DESIGNED TO FIT ON THE TOP CHANNEL OF THE EXTRUSION BODY AS WELL AS REMOTE. CA P E TalkToUs@alwusa com W alwusa com
LIGHTPLANE 1 RECESSED - LP1R
INSTRUCTIONS LIGHTPLANE 1 RECESSED - LP1R Safety & Warnings! When installing or using this recessed fixture basic safety precautions should be followed: 1. Read ALL INSTRUCTIONS before installing 2. This
More informationMEDIA LED. Pendant Standard Mount Installation ou de montage WARNING:
MEDIA LED Pendant Standard Mount WARNING: Disconnect main power at the source prior to installation! Thread gripper base onto 1 /4 20 stud, or with #8 screw. Depress gripper nozzle to insert aircraft cable.
More informationTORi INSTRUCTION SHEET. Minimalist Linear Fixture T5/T5HO. CSS - Cable Suspended. 1. Cut cables to desired length - take care not to fray cable ends.
TORi Minimalist Linear CSS - Cable Suspended J-BOX (BY OTHERS) 3-O or 4-0 MUD RING (BY OTHERS) J-BOX BRACKET BAR 1/4-20 STUD 8-32 BRACKET BAR SCREWS (BY OTHERS) CANOPY STND - 5 CANOPY 1. Cut cables to
More informationLED Flat Panel Installation Instructions For 1 x4, 2 x2, and 2 x4 LED Flat Panels (FP Series)
LED Flat Panel Installation Instructions For 1 x4, 2 x2, and 2 x4 LED Flat Panels (FP Series) PLEASE READ THESE INSTRUCTIONS BEFORE INSTALLATION PLEASE READ THESE INSTRUCTIONS BEFORE INSTALLATION SAFETY
More informationTwo Circuit Trac System TRAC SECTION, JOINERS & FEEDS
Project: Fixture Type: Location: Contact/Phone: PRODUCT DESCRIPTION DIMENSIONS Low profile, two-circuit trac sections for surface or pendant mounting. Provides two separate 20-amp circuits from a single
More informationD3 INSTALLATION GUIDE
D3 INSTALLATION GUIDE Supported Models D3-FXRD D3-FXSQ D3-ADRD D3-ADSQ D3-WWRD D3-WWSQ D3 INSTALLATION GUIDE 770-000028-0X r09 PAGE 1 ! WARNING! Shock Hazard. May result in serious injury or death. Turn
More informationBionic Perimeter Standard C o v e & P e r i m e t e r
Type Job Name Catalog Number Bionic Perimeter Standard C o v e & P e r i m e t e r 5 7 /16" 110mm 6 7 /16" 170mm 8 7 /16" 221mm Flush Regress 3" Regress ordering - BIO-PSTD (STANDARD) series/ style lamp
More informationOne Circuit Trac System TRAC SECTION, JOINERS & FEEDS T Series
Project: Fixture Type: Location: Contact/Phone: PRODUCT DESCRIPTION DIMENSIONS Low-Profile, single-circuit trac sections for surface or pendant mounting. I-beam cross section provides added strength and
More informationTRAC-LITES One Circuit Trac System TRAC SECTIONS & SYSTEM COMPONENTS R Series
Project: Fixture Type: Location: Contact/Phone: PRODUCT DESCRIPTION DIMENSIONS Reduced-profile, single-circuit trac sections for surface or pendant mounting. Compatible with a full range of feed, connector
More informationLuminaire PROFILE-SPOKE 15 UP 85 DN LED (PS1-D) Type. Notes. Performance Summary D OPTIONS 3S A 28 W B 34 W C 44 W D 57 W
T F W 604.549.9379 604.549.9555 fluxwerx.com PROFILE - SPOKE Specification Data Luminaire PROFILE-SPOKE 15 UP 85 DN LED () Type Project Profile Spoke 3 (S3) Product Notes Profile Spoke 4 (S4) Performance
More informationPROFILE 50 Up 50 Dn PF1-E. Luminaire PROFILE - 50 UP 50 DN LaED (PF1-E) Type. Project. Product. Notes. Performance Summary
T F W 604.549.9379 604.549.9555 fluxwerx.com PROFILE Specification Data PROFILE - 50 UP 50 DN LaED () Type Project Product Notes 50 Up I 50 Down A B C D Light (lm) 2350 2900 3500 4450 Energy (W) 19 24
More informationInstallation Instruction
T F W 604.549.9379 604.549.9555 fluxwerx.com Installation Instruction DRIVER ENCLOSURE Ceiling Type Version Grid Battery Pack GRID MOUNT INSTALL OPTIONS OPTION 1: Standard Vertical Grid drivers can be
More informationINTEGRID TRACK (120V) SPECIFICATIONS
INTEGRID TRACK (120V) SPECIFICATIONS GENERAL Integrid Track shall be a combination Track and main runner for mech - anically supporting suspended ceiling systems. Integrid Track shall allow fixtures to
More informationOne Circuit Trac System TRAC SECTION, JOINERS & FEEDS T Series
Project: Fixture Type: Location: Contact/Phone: PRODUCT DESCRIPTION DIMENSIONS Low-Profile, single-circuit trac sections for surface or pendant mounting. I-beam cross section provides added strength and
More informationHBDBM High Bay Series
HBDBM High Bay Series INSTALLATION INSTRUCTIONS The High Bay Luminaire is ideal for installations with mounting heights over 25 feet. The fixture can be mounted with a hook or pendant with flexible adjustments
More informationHP-2 / HP-6 Direct Installation Instructions Overview
Overview Helpful Video 0-10V Dimming Step 1 Mounting & Suspension Page 2 Step 2 Identification & Preparation Page 3 Step 3 Mounting to Structure Page 4 NOTE Step 4 Page 5 This installation requires proper
More informationGEMINI HOUSING SPECIFICATIONS
GEMINI HOUSING SPECIFICATIONS GENERAL Gemini Housing shall support Track of six foot intervals. In addition, the extra compartment shall be able to be used for a multitude of elec trical or mechanical
More informationInstallation Instructions MX LED Enhanced Color Adjustable
Installation Instructions 1 of 5 MX Enhanced Color Adjustable Risk of electrical shock. Disconnect power before servicing or installing luminaire. Risk of injury or damage. will fail if not installed properly.
More informationLuminaire PROFILE-SPOKE Ind. Up Dn Control (PS3-B) Type. Project. Notes. Performance Summary OPTIONS 4S D 76 W 3S D 57 W
T F W 604.549.9379 604.549.9555 fluxwerx.com PROFILE - SPOKE Specification Data Luminaire PROFILE-SPOKE Ind. Up Dn Control () Type Project Profile Spoke 3 (S3) Product Notes Profile Spoke 4 (S4) Performance
More informationRECESSED TRACK (120V) SPECIFICATIONS
RECESSED TRACK (120V) SPECIFICATIONS GENERAL Recessed track shall be approved by the NEC for flush-mounting into ceiling or any flat surface. Recessed Track shall allow fixtures to be easily focused, switched,
More informationNT-300 Series Single Circuit Track System & Accessories
NT-300 Series Single Circuit Track System & Accessories Type Project Catalog No. Lamp/Wattage PRODUCT DESCRIPTION Low profile, extruded aluminum track with 20-Amp rated flat, solid integral copper conductors.
More informationCustomer service: or Upper mounting ring. Canopy
Components included: Upper mounting ring Canopy Fixture base Fluorescent - 2 x 42 W 4-pin compact fluorescent lamps required (not included). Lutron recommends GE, Sylvania, or Philips lamps that are certified
More informationTwo Circuit Trac System TRAC SECTION, JOINERS & FEEDS
Project: Fixture Type: Location: Contact/Phone: PRODUCT DESCRIPTION DIMENSIONS Low-Profile, two-circuit trac sections for surface or pendant mounting. Provides two separate 20-amp circuits from a single
More informationLOOP 65 Up 35 Dn LS1-A. Luminaire LOOP - 65 UP 35 DN LED (LS1-A) Type. Project. Product. Notes. Performance Summary OPTIONS
T F W 604.549.9379 604.549.9555 fluxwerx.com LOOP Specification Data LOOP - 65 UP 35 DN LED () Type Project Product Notes 65 Up I 35 Down A B C D Light (lm) 2500 3050 3750 4900 Energy (W) 19 23 29 38 Efficacy
More information2 CIRCUIT TRACK. Notes: INSTALLATION PROFILE SURFACE TRACK COLOR. Page 1/9. Date :12/06/17 Rev.02 WHITE POWDER COAT SILVER ANODIZED
2 CIRCUIT TRACK SURFACE TRACK COLOR INSTALLATION PROFILE WHITE POWDER COAT SILVER ANODIZED PLASTER FLANGE RECESSED VISIBLE FLANGE RECESSED BLACK ANODIZED Page 1/9 SURFACE TRACK SYSTEM : compose your system
More informationInde-Pendants Family. 32L Cylinder with Ring Chicago Plenum Ceiling Types. Document No
Inde-Pendants Family 32L with Ring Chicago Plenum Ceiling Types Installation instructions for: 32L-CRxx-P-ID-CCEA 32L-CRxx-P-D-CCEA Document No. 32L Inde-Pendants: with Ring (Plaster Trim, Grid and Drywall
More informationMOUNTING SYSTEMS SPECIFICATIONS
MOUNTING SYSTEMS SPECIFICATIONS GENERAL Mounting Systems shall allow Track Systems to be fastened to or from various surfaces in a wide range of safe and approved methods. Mounting Systems shall have a
More informationSPORTSTER SADDLEBAG KIT. i i02212
General These saddlebags are designed to fit 99 and later Sportster Model Motorcycles, except XL00 Sport models with gas reservoir shock absorbers and 88R models. See the Service Parts pages for a list
More informationSunwize Power Ready Express Quick Start
Document # 310002 Sunwize Power Ready Express Quick Start The purpose of this guide is to assist you in setting up your system quickly and efficiently. Important! Prior to field installation Determine
More informationInstallation Instructions Vanishing Lid Bracket
-800-447-88 www.coverpools.com Installation Instructions Vanishing Lid WARNING FOR YOUR SAFETY This product must be installed and serviced by a contractor who is licensed and qualified in pool equipment
More informationINSTALLATION MANUAL. Melink Corporation (513) Revision
INSTALLATION MANUAL Revision 130711 Table of Contents Step Installation Contractor Page 1 Install System Controller Electrical 4 2 Install Variable Frequency Drive Electrical 6 3 Install Touchpad Mechanical
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS This document explains mounting for pendant, recessed, and wall PENDANT - STEP ONE INSTALL MOUNTING POINTS Non-power feed mounting points may be positioned 1 to 12 or 12 to 18
More informationNULB-8 Series silk sbc led lightbar 24V LED Light Bar Source: 5W / 350Lumen / 90+CRI per ft
PRODUCT DESCRIPTION Nora Lighting s Silk SBC LED is a 24V interlock LED strip. Its low-profile, Title 24 compliant fixtures provide excellent and even illumination on all surfaces. Producing over 90+CRI
More informationHP-4 Recessed with Regressed Visible Flange Starter/Independent Installation Instructions
HP-4 Recessed with Regressed Visible Flange /Independent Scan QR code for helpful video(s) Step 1 Cutout Dimension Step 2 Step 3 0-10V 5" 7/8" Feed "A" A + 1/4" +/- 1/1 3/4" Nominal Length Add 1/4" to
More informationLuminaire Support Location Cable Mounting Kit. Non-Power Feed
INSTALLATION INSTRUCTIONS These installation instructions are used for installing the following luminaires and kits: Luminaire Support Location Cable Mounting Kit OLE4 (suspended) Normal Power Feed Non-Power
More informationLuminaire PROFILE-SPOKE 40UP 60 DN LED (PS1-A) Type. Notes. Performance Summary OPTIONS CONTROLS
T F W 604.549.9379 604.549.9555 fluxwerx.com PROFILE - SPOKE Specification Data Luminaire PROFILE-SPOKE 40UP 60 DN LED () Type Project Profile Spoke 3 (S3) Product Notes Profile Spoke 4 (S4) Dw DYNAMIC
More informationPROFILE 100 Dn PF1-B. Luminaire PROFILE DN LED (PF1-B) Type. Project. Product. Notes. Performance Summary
T F W 604.549.9379 604.549.9555 fluxwerx.com PROFILE Specification Data PROFILE - 100 DN LED () Type Project Product Notes LED Product Partner Dw DYNAMIC WHITE 100 Down A B C D Light (lm) 2100 2550 3100
More informationINSTALLATION INSTRUCTION W Track Recessed 120V Flangeless
W Track Recessed 120V Flangeless WT4-RTL, WT8-RTL, WT12-RTL SAFETY INSTRUCTION Read all of these instructions before installing the track system. Turn off power at main switch before installing or modifying
More informationLED IMPORTANT SAFETY INSTRUCTIONS
READ AND FOLLOW ALL SAFETY INSTRUCTIONS! SAVE THESE INSTRUCTIONS AND DELIVER TO OWNER AFTER INSTALLATION To reduce the risk of death, personal injury or property damage from fire, electric shock, falling
More informationALL700RM-230V INSTALLATION INSTRUCTIONS
ALL700RM-230V INSTALLATION INSTRUCTIONS Aladdin Light Lift, Inc. (256) 429-9700 61 Shields Road (877) 287-4601 Huntsville, AL 35811 www.aladdinlightlift.com Patent #5105349 WARNING: Disconnect power source
More informationSURFACE/CEILING & SUSPENDED MOUNT INSTALLATION
SURFE/CEILING & SUSPENDED MOUNT INSTALLATION E477827 E477827 APPLICATION NL luminaires are designed for use indoors, outdoors, wet locations, areas containing moisture, dirt, corrosion, vibration and rough
More informationMEDMASTER DOWNLIGHT Luminaires for Surgical Applications
PRODUCT FEATURES: 6" sealed, recessed downlight with regressed or flush lens trim Conducted emissions controlled as per MIL-STD-461F Delivered lumens: 794-5,543 lm 1% Dimming via 0-10V, DALI or EcoSystem
More information1718 W. Fullerton Ave Chicago, IL Tel: Fax:
206 Edge Lighting. All Rights Reserved. Installation Instructions for Nova Power Suspension Up/Down - Center Feed Glide Up/Down - Center Feed IMPORTANT INFORMATION - This product is suitable for indoor
More information1Unpack fixture. Suspensions/canopies are ordered and
DO NOT REMOVE THE LED ASSEMBLY. THIS WILL VOID THE WARRANTY. Call Zumtobel at 1-800-448-4131 questions. Fixture is intended installation in accordance with bee servicing. Retain these instructions 2Determine
More informationA CHANNEL. Installation Instructions for Tie Stix Wall 2-Light. Section One: 4SQ Version
0 Edge Lighting. All Rights Reserved. W. Fullerton Ave Chicago, IL 0 Tel: -0- Fax: -- www.edgelighting.com info@edgelighting.com Installation Instructions for Tie Stix Wall -Light IMPORTANT INFORMATION
More informationTrack Accessories. Single Circuit Track. L Connector T Connector X Connector. Mini Connector Floating Canopy End Feed Kit.
Single Circuit Single Circuit Track Live End Connector Flexible Connector Straight Connector Track supplied with dead end and mounting hardware Live end connector used for direct wiring Flexible connector
More informationWARNING NORDIC ALUMINIUM LIGHTING TRACK SYSTEMS
WARNING NORDIC ALUMINIUM LIGHTING TRACK SYSTEMS DO NOT solder connectors as this will prohibit the adapters circuit switch to move freely from circuit to circuit. Nordic Aluminium track adapters and accessories
More informationHigh Bay Luminaire Series
High Bay Luminaire Series INSTALLATION INSTRUCTIONS The High Bay Luminaire is ideal for installations with mounting heights over 25 feet. The fixture can be mounted with a hook or pendant with flexible
More informationCIRRUS SUSPENSION WALL WASH WITH REMOTE POWER, END FEED
Adjustable Max. 5 ft. Description Cirrus Suspension Wall Wash with Remote 24VDC power supply (sold separately) is a linear LED fixture that offers a wall wash lens for a smooth and uniform beam spread.
More informationAssembly Instruction Sheet #IS-MCLG337RC For Style MCLG337RC
Quoizel, Inc. 6 Corporate Parkway Goose Creek, SC Customer Service Phone 63.273.2700 Fax 63.23.702 www.quoizel. ToolsRequired:Flatheadscrewdriver,Phillipsscrewdriver,pliers,wirecutters,wire strippers,electricaltape,safetyglasses.
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS IMPORTANT Before opening your Lights.com fixture, please make sure that you carefully read through these instruction sheets. Consider having your fixture installed by a qualified
More informationALL W INSTALLATION INSTRUCTIONS
ALL1000-3300W INSTALLATION INSTRUCTIONS Aladdin Light Lift, Inc. (256) 429-9700 61 Shields Road (877) 287-4601 Huntsville, AL 35811 www.aladdinlightlift.com Patent #5105349 WARNING: Disconnect power source
More informationSURFACE TRACK (120/250V) SPECIFICATIONS
SURFACE TRACK (120/250V) SPECIFICATIONS GENERAL Lighting Track shall allow fixtures to be located anywhere along the track length. Fixtures shall be easily focused, switched, dimmed, accessorized and removed
More informationALL200RM/ALL200RM-CM
ALL200RM/ALL200RM-CM INSTALLATION INSTRUCTIONS Aladdin Light Lift, Inc. (256) 429-9700 61 Shields Road (877) 287-4601 Huntsville, AL 35811 www.aladdinlightlift.com Patent #5105349 WARNING: Disconnect power
More informationThe Tracking Magnet Recessed High-tech LED lighting system for interior architecture
Description The Tracking Magnet system is creative, flexible, reliable and precise. Accent fixtures can be rapidly exchanged and repositioned without tools using the magic of magnets. A variety of accent
More informationNOTE: The orientation of the mounting brackets are critical. (See Figure 4)
Page 1 of 5 11.25.13 Lamping Specifications 10138 I-wall 2 120v, One, F14WT5/Mini Bi-Pin 277v, One, F14WT5/Mini Bi-Pin 10139 I-wall 3 120v, One, F21WT5/Mini Bi-Pin, 277v, One, F21WT5/Mini Bi-Pin 10140
More informationInstruction Sheet SRSR SERIES. Rotating Sliding Rail System
Instruction Sheet SRSR SERIES Rotating Sliding Rail System THANK YOU Thank you for purchasing the SRSR Series Rotating Sliding Rail System. Please read these instructions thoroughly before assembling this
More informationAluminum Valve Cover Adapter Small Block Chevy to LS Engine
Aluminum Valve Cover Adapter Small Block Chevy to LS Engine PARTS LIST: 241-296 (Polished Finish) 241-297 (Black Finish) 241-298 (Natural Cast Finish) Instruction Sheet 199R11685 Qty. Description 1 Driver
More informationLED Garage Light INSTALLATION INSTRUCTIONS. *Model number noted on carton label
LED Garage Light *Model number noted on carton label INSTALLATION INSTRUCTIONS Model Number / Número de Modelo / Numéro des modèle SGLL 24 PIR (24 LED Garage Light) Actual Dimensions 10 W x 3-1/2 H x 24-1/2
More informationInstallation Instructions 4 Gravity Enhanced Color Adjustable
Installation Instructions 1 of 5 Risk of electrical shock. Disconnect power before servicing or installing luminaire. Risk of injury or damage. will fail if not installed properly. Follow installation
More informationMIRRORLITE RECESSED EMERGENCY LIGHTING
1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. MIRRORLITE RECESSED EMERGENCY LIGHTING INSTALLATION AND OPERATING INSTRUCTIONS IMPORTANT SAFEGUARDS When using electrical equipment, basic safety precautions should
More informationWhen using electrical equipment, basic safety precautions should always be followed including the following:
INDUSTRIAL INSTALLATION INSTRUCTIONS Illumina BS100LED2FT-PLUS EACH MODEL NUMBER CONSISTS OF THE FOLLOWING: SERIES / LENGTH / OPERATION / LUMENS / COLOUR TEMP. / INPUT SERIES: LENGTH: OPERATION: BS100LED2PLUS
More informationAlphabet By Ledra Brands
700 Track 700 Track 700 Track is a 1 circuit, 20A rated, line voltage track system. Its lightweight, compact elegant design is easy to install saving on overall project costs. The track is a 120v 1-circuit
More informationLamp: 7WDC 27K WDC 30K DC 27K DC 30K
Made in the USA 12"- 144" 1.025" (2.6cm) (0.76cm) Cirrus Channel Wall Grazer features a lens that provides dramatic accent lighting to highlight textured surfaces. At 7 or 10.5 watts per foot, the 24 volt
More informationGeneral Installation Instructions LED
General Installation Instructions LED To reduce the risk of death, personal injury or property damage from fire, electric shock, falling parts, cuts/abrasions and other hazards, please read all warnings
More informationCOMMALITE CML Suspended, Wall, Ceiling LED
COMMALITE CML LED Find additional images and information at alwusa.com/cml 1. BASE MODEL CMLS Cable suspended CMLSM.6.4 1 Stem mount, 6" arms, JBOX4 canopy CMLSM.6.2 2 Stem mount, 6" arms, JBOX2 canopy
More informationNULB-5 Pro90 Series ILLUMINATING THE FUTURE...SINCE Ultra-Low Profile Linear LED Lightbar PLUS. Type Project Catalog No.
Ultra-Low Profile Linear LED Lightbar Pro 90 Source: 8W per foot PRODUCT DESCRIPTION Nora Lighting s low-profile, Title 24 compliant fixtures provide excellent and even illumination on all surfaces. At
More informationINSTALLATION MANUAL. Recessed In-Ceiling Motorized Projection Screen
INSTALLATION MANUAL Recessed In-Ceiling Motorized Projection Screen IMPORTANT: BEFORE YOU BEGIN To avoid staining or scratching the screen, wash your hands and clean the work area before starting. Do not
More informationINSTALLATION MANUAL 2000WCY
INSTALLATION MANUAL 2000WCY Pressure Cleaning System spraymastertech.com Spray Master Technologies is a quality product line of Assembled Products Corp. 115 E. Linden Rogers, Arkansas 72756 USA (479) 636-5776
More informationMirror Solutions Bevel & Pivot Models Installation Instructions INSTALLATION INSTRUCTIONS. Figure 1
Installation Instructions Mirror Solutions Bevel & Pivot Models 620095-620098 Mirror Solutions Bevel - Models # 620095 & 620096 Mirror Solutions Pivot - Models # 620097 & 620098 Figure 1 INSTALLATION INSTRUCTIONS
More informationPROPER ELECTRICAL CONNECTIONS
INSTALLATION 230 Volt 13 ampere 50 Hz The SUITMATE Swimsuit Water Extractor has been designed and manufactured with safety as our primary consideration. Therefore, it is important that the unit be installed
More informationTechnical Installation Manual
Lighting Step and Aisle Safety Lighting Technical Installation Manual 1 Contents Page 3 Tools required 4 Installation detail & planning 5 Adhesives, silicone & crimps 6 General cinema layout 7 Basic wiring
More informationLED Recessed Troffer Retrofit Kit
Model # TRK series LED Recessed Troffer Retrofit Kit Installation Instructions PACKAGE CONTENTS A B E Part Item Name Qty. A Retrofit assembly 1 B Bracket 2 C Sheet metal screw 4 D Wire nuts 5 E Gap channel
More informationPlasma Display Electric Ceiling Lifts
I N S T R U C T I O N M A N U A L The Plasma Display Electric Ceiling Lift is designed for plasma displays requiring an extended drop (18 to 42 inches) from their hidden location. The lift is designed
More informationInstallation Instructions Studio Makeup Station
Installation Instructions Studio Makeup Station 30" and 36" Models 5-light 30" Studio Makeup Station 8-light 30" Studio Makeup Station 6-light 36" Studio Makeup Station 9-light 36" Studio Makeup Station
More informationNIOB-2 2" BWF IOLITE TRIMS
NIOB-2 2" BWF IOLITE TRIMS New Construction or Remodel Housing Required Source: LED, 14 Watts, 8 Lumens Nora Lighting s 2" Iolite BWF trims are small aperture downlights that can be specified for use in
More informationALL700/ALL700-CM INSTALLATION INSTRUCTIONS
ALL700/ALL700-CM INSTALLATION INSTRUCTIONS Aladdin Light Lift, Inc. (256) 429-9700 61 Shields Road (877) 287-4601 Huntsville, AL 35811 www.aladdinlightlift.com Patent #5105349 WARNING: Disconnect power
More informationw w w. h d o n l i n e s h o p. d e LAYBACK LICENSE PLATE AND TURN SIGNAL RELOCATION KIT INSTALLATION GENERAL -J03892 REV Kit Number
-J0 REV. 00-0-0 LAYBACK LICENSE PLATE AND TURN SIGNAL RELOCATION KIT GENERAL Kit Number 0-0 Models For model fitment information, please see the P&A Retail Catalog or the Parts and Accessories section
More informationRenogy MTS-TM100. Flat Roof Tilt Mount E Philadelphia St, Ontario, CA Version: 1.1
Renogy MTS-TM100 Flat Roof Tilt Mount 2775 E Philadelphia St, Ontario, CA 91761 1-800-330-8678 1 Version: 1.1 Important Safety Instructions Please save these instructions. This manual contains important
More informationINSTALLATION INSTRUCTIONS LIGHTPLANE 3.5. LP3.5 Suspended LED. A nd Avenue, Unit 1. CA P E W alwusa.
Oakland, INSTALLATION INSTRUCTIONS LIGHTPLANE 3.5 LP3.5 Suspended LED A 1035 22nd Avenue, Unit 1 n CA 94606 P 510.489.2530 E TalkToUs@alwusa.com W alwusa.com Safety & Warnings! 1. Read all instructions.
More informationREAD AND FOLLOW ALL SAFETY INSTRUCTIONS! SAVE THESE INSTRUCTIONS AND DELIVER TO OWNER AFTER INSTALLATION
READ AND FOLLOW ALL SAFETY INSTRUCTIONS! SAVE THESE INSTRUCTIONS AND DELIVER TO OWNER AFTER INSTALLATION To reduce the risk of death, personal injury or property damage from fire, electric shock, falling
More informationLumination TM LED Luminaires Suspended LED Fixture (Series EP14)
GE Lighting Solutions Installation Guide Lumination TM LED Luminaires Suspended LED Fixture (Series EP14) Features Long life (50,000 hour rated life) 5 year warranty IP30 Dry location rated BEFORE YOU
More informationCetra Assembly Instructions
99877 Revision F- Complete Series Master Packet If you have any questions concerning these instructions, please call Kimball Office Customer Service. 0 Kimball International, Inc. T 800.8.88 F 8.8.800
More informationThe Gallery System DIRECTIONS. Components of the System
The Gallery System Components of the System DIRECTIONS NOTE: The Gallery Lighting System now includes a sophisticated Junction Box with circuit breakers which will automatically switch the system off if
More informationinstall o IIVIPORTANT - Savethese -&WARNING - -&WARNING - This appliance must -&WARNING - Before beginning the Mode_s PB970, PB975
install m ctric Ran Mode_s PB970, PB975 I[_ Questions? Call 800.GE.CARES (800.432.2737) or Visit our Website at: ge.com I BEFORE YOU BEGIN Read these instructions completely and carefully. o IIVIPORTANT
More informationElectrical Applications. Metal Framing & Cable Tray Superstrut Metal Framing System. Column A. Design Data: Materials: Column B
Electrical Raceway Series 800 Surface Raceway and Lighting Systems Superstrut channel together with snap-in closure strip is listed by Underwriters Laboratories as a surface metal raceway. Other accessories
More informationLumination TM LED Luminaires LAL Series - Continuous Run Option
GE Lighting Installation Guide Lumination TM LED Luminaires LAL Series - Continuous Run Option BEFORE YOU BEGIN Read these instructions completely and carefully. WARNING/AVERTISSEMENT RISK OF ELECTRIC
More informationJuno Trac-Master Trac Lighting Systems. Comprehensive line and low voltage track systems
Juno Trac-Master Trac Lighting Systems Comprehensive line and low voltage track systems Juno Trac-Master System Safe and simple installation is what you can expect from Juno one-circuit and two-circuit
More informationES44-LED SERIES DIRECT OR INDIRECT HIGH EFFICIENCY LED - RECESSED, SURFACE, WALL OR SUSPENDED
ES44-LED SERIES DIRECT OR INDIRECT HIGH EFFICIENCY LED - RECESSED, SURFACE, WALL OR SUSPENDED PERFORMANCE CHARACTERISTICS Optical Efficiency: 90.5% max Lumens per watt: 180 max Lumen output: 2200Lm/ft
More informationRegressed Optic. Sheetrock. Finelite, Inc Whipple Road Union City, CA (510) Fax: (510)
High Performance Grazer (HP-WG) 10 Industry Best Year LED Warranty Date Project Type Comments 6"W x 6"D Flat (Standard) Endcap DESCRIPTION The High Performance Grazer (HP-WG) is a perimeter luminaire that
More informationL-SERIES CLUTCHES L-SERIES CLUTCHES. Getting Started INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS
L-SERIES CLUTCHES INSTALLATION INSTRUCTIONS Thank you for purchasing your new L-Series Clutches. They have been custom-made from the highest quality materials. to the dimensions you specified. With the
More informationA B C D E F. Tools Required (supplied by others)
Page 1 of 17 Parts List Below Deck Automatic Retractable Security Cover Kit (1) Tube End Bearing Plate (A) (1) Rope Reel and Cover Drum Motor Assembly (B) (1) Cover Drum (1) Pulley Support Channel (2)
More informationParts List ILLUSTRATION #1
Installation Instructions BR20 Rear Bumper Replacement Part Number 28295T 2015-2016 Ford F-150 2/4WD Do not attempt to install this product on any vehicle other than the one listed above! Parts List Item
More informationCOMPACT BUSWAY 40 & 60 AMP HOUSING
40 & 60 AMP HOUSING B40 & HOUSING Each Track Busway housing section consists of an extruded aluminum housing with an insulated strip containing copper conductors mounted on the top interior wall. The aluminum
More informationREAD AND FOLLOW ALL SAFETY INSTRUCTIONS! SAVE THESE INSTRUCTIONS AND DELIVER TO OWNER AFTER INSTALLATION.
Installation Instructions 2RTLEDR/2RTLEDRT Relight Assembly READ AND FOLLOW ALL SAFETY INSTRUCTIONS! SAVE THESE INSTRUCTIONS AND DELIVER TO OWNER AFTER INSTALLATION. IMPORTANT SAFETY INSTRUCTIONS WARNING:
More informationSource: 209.2LM per foot, 2.7W per foot
ILLUMINATING THE FUTURE...SINCE 1989 Type Project Catalog No. Lamp/Wattage NUTP51-W100LED9 Series 24V Continuous Hy-Brite LED Tape Light Source: 209.2LM per foot, 2.7W per foot Dimensions Max 32FT. PRODUCT
More information800 TO 9000 LUMEN 8 LED SILENT CEILING DOWNLIGHT HYPERBOLIC OPEN APERTURE L8 SERIES
ENVIRONMENTALLY FRIENDLY, ENERGY EFFICIENT Lumen packages suitable for ceiling heights ranging from 8 to over 100 Efficacies up to 109 lm/w Superior-quality white LED light output using Chip on Board technology
More informationA B C D E F. b.tools Required (supplied by others) 3/16" Drill Bit 3/8" Wrench Phillips Head Screwdriver
Page 1 of 13 5E.1 Parts List a. Below Deck Automatic Retractable Security Cover Kit (1) Tube End Bearing Plate (A) (1) Rope Reel with Motor Attached (B) (1) Rope Reel Cover (C) (1) Cover Drum (1) Cover
More informationPROJECTOR ACCESSORIES
PROJECTOR *To order select accessories in white or silver, simply add a W for white or an S for silver to the end of the part number. CEILING PLATES CMA100 8" (203 mm) CEILING PLATE WITH ADJUSTABLE 1-1/2"
More informationQty: L6JR2 Continuous Flange (Flangeless Endcaps) 1B25 1,2 430lm/6.3W per foot. 1B30 1,2 480lm/7.2W per foot. 1B lm/8.5w per foot K
Date: Customer: Project: Type: Qty: M60 Order Code: - - - - - - - - - - - Series L60J Multi-Mount Form L6JR Continuous Flange (Flanged Endcaps) L6JR Continuous Flange (Flangeless Endcaps) Light Engine,,
More information