Source: 209.2LM per foot, 2.7W per foot

Transcription

1 ILLUMINATING THE FUTURE...SINCE 1989 Type Project Catalog No. Lamp/Wattage NUTP51-W100LED9 Series 24V Continuous Hy-Brite LED Tape Light Source: 209.2LM per foot, 2.7W per foot Dimensions Max 32FT. PRODUCT DESCRIPTION Nora's new Continuous LED Tape is the perfect solution when you need more light than Nora's Standard LED Tape but less than Nora's high Performance Continuous LED Tape. Producing lumens per ft., Damp Label* IP44 culus Llisted the Continuous LED Tape uses the same connectors and accessories as the Continuous High Output LED Tape. The low profile tape is the ideal for coves, architectural details, under and in cabinets, toe kicks, and back lighting. IP44 rated, Continuous LED Tape can be used outdoors when not exposed to direct water spray. Features 100' Spool - Economical and Efficient 90+ CRI Superior Color rendition White finish tape - More efficient reflectance Lumens per foot 2.7W per foot 24V DC System Single color illumination with 3 colors temperature (4200K, 3000K, 2700K) 120º Beam Angle No soldering required Field cuttable every 4" Maximum Run: 32' Dimmable with dimable power supply Easy to install with pre-applied 3M TM tape or clips culus Listed and IP44 Rated for Damp* location Included with every roll: (1) 100' Tape Light Roll, (50) Acrylic Mounting Clips with screws, (1) 12" Power Connector Construction The Continuous LED Tape can be cut every 4 LEDs at marked 4" intervals. Cutting does not effect circuit. Easy flip style snap-on connectors connect to the cut ends. mounting Each Tape Light roll comes with pre-applied 3M adhesive tape for simple installation. Driver: A wide variety of drivers are available from direct plug-ins, Class II, and Hardwire Dimmable Class II Drivers up to 300 Watts. Compatible with Nora Switchex All-in-One dimmer and driver. ELECTRICAL Power: 24V DC Input / 2.7Watts Per Foot Light Source: 12 Hy-Brite LEDs Per Foot Operating Temperature: -25ºC ~ 45 C max Life Expectancy: 50,000 Hours Maximum Run Length: (Single Maximum Run Lenth) 32' H: 1/16" W: 1/2" L: 100' (32' Max-Run) DIMMABLE There may be some cases that require more than one lighting fixture to be used to meet minimum dimmer load. Consult with dimmer manfacturer. Click Here or refer to for complete updated dimmer list in the "Compatibility" page under the "Resource" tab. LABEls and listings culus Listed for Damp* Location IP44 Rated 3 Year Limited Warranty 24V Continuous Hy-Brite LED Tape Light Catalog No. Finish Length Source CRI Color Temp NUTP51 W= White Finish 100 = 100' LED 9= = 2700K FT = Custom Cut 30= 3000K (Specify by Ft.) 42 = 4200K NUTP CUT - Custom cut surcharge (One per cut) Hardwire NATL-SWEX100/24: 100W 24V Nora Switchex All-in-one LED Driver and Dimmer NATL-5100HW: 100W 24V Hardwire Electronic Driver NMTD-60/24D: 60W Dimmable Class II Remote HArdware Magnetic Driver NMTD-96/24D: 96W Dimmable Class II Remote HArdware Magnetic Driver NMT-303/24C2D1: 3 x 100W 24V Dimmable Class II Hardwire Magnetic Driver w/ Integral Regular for Constant Current and Voltage NATL-530HW: 30W Class II El. Driver (Requires NRA-6035 or NUSP-JBox) NATL-560HW: 60W Class II El. Driver (Requires NRA-6035 or NUSP-JBox) NATL-596: 24V 96W Class II Plug-In Electronic LED Driver NATL-524: 24W Direct Plug-In El. Driver NATL-545: 45W Direct Plug-In El. Driver DRIVER ACCESSORIES NRA-125/6: 6" Extension Cord for NATL-530HW & NATL-560HW NRA-125/12: 12" Extension Cord for NATL-530HW & NATL-560HW NRA-125/18: 18" Extension Cord for NATL-530HW & NATL-560HW NRA-125/72: 72" Extension Cord for NATL-530HW & NATL-560HW NRA-6035W/6: 6' Cord and Plug for NATL-530HW & NATL-560HW NRA-6035W/10: 10' Cord and Plug for NATL-530HW & NATL-560HW NALTL-10: 10' Replacement Power Line Connector for NATL-530HW & NATL-560HW NALTL-30: 30' Replacement Power Line Connector for NATL-530HW & NATL-560HW NUSP-JBox: Junction Box required for hardwiring NATL-530HW & NATL-560HW/12 TAPE LIGHT ACCESSORIES NATL-302: 5" Power Line Splitter NATHR-680: 4' NATHR-685: Clear Acrylic Mounting Clips (Pack of 15) NATL-404W: J-Clip for Wire, White Plastic (10/pk) NATL-405W: Over the Wire Clip, White Plastic (10/pk) NATL-406W: Wire Clip for Wire, White Plastic (10/pk) NATL-407: 4-Way Terminal/Splitter Block NATL-408: 8-Way Terminal/Splitter Block NATL-415W: Low Voltage Splice Box NATL-C23: 4', Shallow w/ Wings NATL-C24: 4', Shallow NATL-C25: 4', Deep w/ Wings NATL-C26: 4', Deep NATL-C27: 4', J-Style NATL-C28: 4', Corner NATLCFC-600: Flip Type Link Connector, 12" NATLCFC-609/3: Flip Type DC Plug Connector, 3" NATLCFC-609/12: Flip Type DC Plug Connector, 12" NATLCFC-609/48: Flip Type DC Plug Connector, 48" NATLCFC-609/96: Flip Type DC Plug Connector, 96" NATLCFC-601: Flip Type Interconnect Cable, 1" NATLCFC-603: Flip Type Interconnect Cable, 3" NATLCFC-606: Flip Type Interconnect Cable, 6" NATLCFC-612: Flip Type Interconnect Cable, 12" NATLCFC-624: Flip Type Interconnect Cable, 24" NATLCFC-648: Flip Type Interconnect Cable, 48" NATLCFC-672: Flip Type Interconnect Cable, 72" NATLCFC-696: Flip Type Interconnect Cable, 96" NATLCFC-608/3: Flip Type Splice Connector, 3" NATLCFC-608/12: Flip Type Splice Connector, 12" NATLCFC-608/48: Flip Type Splice Connector, 48" NATLCFC-608/96: Flip Type Splice Connector, 96" NATL-518: In-Line Dimmer (12V & 24V, 72W Max) NATL-422W: 2 Wire Raceway (White). Field cuttable plastic (Includes wire channel with double faced tape and cover) NATL-422B: 2 Wire Raceway (Black). Field cuttable plastic (Includes wire channel with double faced tape and cover) NATL-W : 16AWG In-Wall Rated Wire (250') NATL-W : 16AWG In-Wall Rated Wire (20')

2 24V Continuous LED Tape Light Accessories Flip Type Link Connector, 12mm NATLCFC-600 Flip Type Interconnector Cable NATLCFC-601 1" NATLCFC " NATLCFC-603 3" NATLCFC " NATLCFC-606 6" NATLCFC " NATLCFC " for linking 2 pieces of NUTP51 tape 1.18 Flip Type Splice Connector Cable NATLCFC-608/3 3" NATLCFC-608/48 24" NATLCFC-608/12 12" NATLCFC-608/96 48" Flip connector for NUTP51 to power or joining tape (No DC plug) Flip Type DC Plug Connector Cable NATLCFC-609/3 3" NATLCFC-609/48 24" NATLCFC-609/12 12" NATLCFC-609/96 48" Flip connector for NUTP51 to power or joining tape with DC plug 4' w/lens NATL-C23 Shallow Wings NATL-C24 Shallow 4' w/lens NATL-C25 Shallow Wings NATL-C26 Shallow ' NATL-C27 J-Style NATL-C28 Corner w/lens 4' NATHR-680 2' Wire Raceway NATL-422B Black NATL-422W White Field-cuttable plastic. Includes wire channel with double faced tape and cover. Black or White. Mounting Clip NATL-40 Pack of 5 In-Line Touch Dimmer NATL W max., no power failure, touch on/off and hold to dim Nora SWITCHEX All-In-One LED Driver & Dimmer NATL-SWEX100/24 100W 24V Converts 120 VAC to 24V low voltage DC in a standard electrical box. Includes face plate..

3 24V Continuous LED Tape Light Accessories Continued 24V Direct Plug-In LED Driver NATL W NATL W Allows direct connection to a wall outlet with 6' cord and plug. Requires power line interconnection cable. Non- Dimmable. 24V Direct Plug-In LED Driver NATL W Allows direct connection to a wall outlet with 5' cord and plug and 44" power line connector. Requires power line interconnection cable. Non-Dimmable. 24V Class II Hardwire Electronic LED Driver NATL-530HW 30W NATL-560HW 60W Allows hardwiring using NUSP-JBox. Can be converted into direct plug-in driver using NRA Requires power line interconnection cable unless used with NAL-250. Non-dimmable. 24V Class II Hardwire Electronic LED Driver NATL-5060HW 60W NATL-5100HW 100W Can be used with Nora LED Tape, Light Bar and Puck. Allows hardwiring. Includes 10' power line connector (NALTL-10). Non-dimmable Dimmable 24V Class II Remote Hardwire Magnetic Driver NMTD-60/24D 60W NMT-96/24D 96W With integral regulator for constant current and voltage. Includes 10' Power Line Connector (30' ordered separately). Flexible Extension Cord for NATL-530HW OR NATL-560HW NRA-125/6 6" NRA-125/18 18" NRA-125/12 12" NRA-125/72 72" Can be joined together to create custom lengths. Cord & Plug for NATL-530HW OR NATL-560HW NRA-6035W/6 6' NRA-6035W/10 10' Used to convert NATL-530HW or NATL-560HW into a direct plug-in driver. Replacement Power Line Connector NALTL-10 10' 24V NALTL-30 30' 24V For use with NMT Series and NATL-5100HW. Replaces included 10' lead wire, to allow for 30' or less length between Lightbar PLUS run and LED Driver. Power Line Splitter NATL-302 one into two lines. 5" 24V Junction BOx for Hardwiring NUSP-JBox Required for hardwiring NATL-530HW or NATL-560HW. Can be used to feed to separate runs. Accepts Romex. Low Voltage Splice Box NATL-415 Use to join Romex low voltage lead or NATL-W16-2 Nora In-Wall Rated wire to power line connector. In-Wall Rated Wire NATL-W ' NATL-W ' 16 AWG low voltage Class II two-conductor, in-wall rated wire.

4 24V Continuous LED Tape Light Accessories Continued J-Clip for Wire, White Plastic NATL-404W 10/pk Over the Wire Clip, White Plastic NATL-405W 10/pk Wire Clip for Wire, White Plastic NATL-406W 10/pk 4-Way Terminal/Splitter Block NATL "L x 1.125"W x.875"d 8-Way Terminal/Splitter Block NATL-408 4"L x 1.125"W x.875"d

5

6 24V Continuous LED Tape Light Accessories Includes plastic diffuser NATL-C23: 4', Shallow w/ Wings Includes plastic diffuser NATL-C24: 4', Shallow Includes plastic diffuser. Includes plastic diffuser. NATL-C25: 4', Deep with Wings NATL-C26: 4', Deep NATL-C27: 4', J-Style Includes plastic diffuser. NATL-C28: 4', Corner NATHR-680-4' NATL-422W: 2 Wire Raceway (White). Field cuttable plastic (Includes wire channel with double faced tape and cover) NATL-422B: 2 Wire Raceway (Black). Field cuttable plastic (Includes wire channel with double faced tape and cover) 9/16" x 11-1/2" x 1/4" Tape Light snaps into the channel. Field Cuttable. Recommended for most installations.

7 24V continuous led tape light Accessories Flip Type Link Connector, 12mm NATLCFC-600 NUTP51 / NUTP81 NATLCFC-200 NUTP71 Flip Type Interconnector Cable FlipTypeInterconnectorCable Flip Type Splice Connector NATLCFC-601 1" NATLCFC " NATLCFC-603 3" NATLCFC " NATLCFC-606 6" NATLCFC " NATLCFC " for linking 2 pieces of tape NUTP51 or NUTP81 NATLCFC-201 1" NATLCFC " NATLCFC-203 3" NATLCFC " NATLCFC-206 6" NATLCFC " NATLCFC " for linking 2 pieces of tape NUTP71 NATLCFC-608/3 3" NATLCFC-608/12 12" NATLCFC-608/48 48" NATLCFC-608/96 96" Flip connector for NUTP51 / NUTP81 to power or joining tape - No DC plug Flip Type Splice Connector NATLCFC-208/3 3" NATLCFC-208/12 12" NATLCFC-208/48 48" NATLCFC-208/96 96" Flip connector for NUTP71 to power or joining tape - No DC plug FlipTypeDCPlugConnector NATLCFC-609/3 3" NATLCFC-609/12 12" NATLCFC-609/48 48" NATLCFC-609/96 96" Flip connector for NUTP51 / NUTP81 to power with DC plug FlipTypeDCPlugConnector NATLCFC-209/3 3" NATLCFC-209/12 12" NATLCFC-209/48 48" NATLCFC-209/96 96" Flip connector for NUTP71 to power with DC plug 4' w/lens NATL-C23 Shallow Wings NATL-C24 Shallow 4' w/lens NATL-C25 Deep Wings NATL-C26 Deep 4' NATL-C27 J-Style NATL-C28 Corner w/lens 4' NATHR-680 2' Wire Raceway NATL-422(B/W) Field-cuttable plastic. Includes wire channel with double faced tape and cover. Black or White. Mounting Clip NATL-401 Pack of 5. NATL-518 In-Line Touch Dimmer 72W max., no power failure, touch on/off and hold to dim. NATL-SWEX100/24 24V 100W Nora SWITCHEX All-in-One LED Driver and Dimmer Converts 120 VAC to 24V low voltage DC in a standard electrical box. Includes face plate. NATL V 24W NATL V 45W NATL V 96W 24V Direct Plug-In LED Drivers Allows direct connection to a wall outlet with 6' cord and plug (NATL-524 and 545) or 5' cord and plug and 44" power line connector (NATL-596). Requires power line interconnection cable. Non-Dimmable. NATL-530HW 24V 30W NATL-560HW 24V 60W 24V Class II Hardwire Electronic LED Driver Allows hardwiring using NUSP-JBox. Can be converted into direct plug-in driver using NRA Requires power line interconnection cable unless used with NAL-250. Non-dimmable. NATL-5060HW 24V 60W NATL-5100HW 24V 100W 24V Class II Hardwire Electronic LED Driver Can be used with Nora LED Tape, Light Bar and Puck. Allows hardwiring. Includes 10' power line connector (NALTL-10). Non-dimmable. NMTD-60/24D 24V 60W NMT-96/24D 24V 96W Dimmable 24V Class II Remote Hardwire Magnetic Drivers With integral regulator for constant current and voltage. Includes 10' Power Line Connector (30' ordered separately). NRA-125/6 6" NRA-125/12 12" NRA-125/18 18" NRA-125/72 72" Flexible Extension Cord for NATL-530HW or NATL-560HW Used to extend length between NUSP-JBox and NATL-530HW or NATL-560HW. Can be joined together to create custom lengths. NRA-6035W/6 6' NRA-6035W/10 10' Cord and Plug for NATL-530HW or NATL-560HW Used to convert NATL-530HW or NATL- 560HW into a direct plug-in driver. NALTL-10 10' 24V NALTL-30 30' 24V NALTL-302 5" 24V Splitter Replacement Power Line Connector For use with NMT Series and NATL-5100HW. Replaces included 10' lead wire, to allow for 30' or less length between Lightbar PLUS run and LED Driver. NUSP-JBox Junction Box for Hardwiring Required for hardwiring NATL-530HW or NATL-560HW. Can be used to feed to separate runs. Accepts Romex. NATL-415 Low Voltage Splice Box Use to join Romex low voltage lead to power line connector. NATL-W AWG 250' NATL-W AWG 20' In-Wall Rated Wire 16 AWG low voltage Class II two-conductor, in-wall rated wire.

8 24V Continuous LED Tape Light Accessories NATLCFC-600: Flip Type Link Connector, 12mm NATL-415W - Low Voltage Splice Box NATLCFC-609/3: Flip Type DC Plug Connector, 3" NATLCFC-609/12: Flip Type DC Plug Connector, 12" NATLCFC-609/48: Flip Type DC Plug Connector, 48" NATLCFC-609/96: Flip Type DC Plug Connector, 96" NATL End Cap Used to join Romex low voltage lead to low voltage power line connecctor or interconnector A: Width: 1/2" B: Length: 3/8" NATLCFC-608/3: Flip Type Splice Connector, 3" NATLCFC-608/12: Flip Type Splice Connector, 12" NATLCFC-608/48: Flip Type Splice Connector, 48" NATLCFC-608/96: Flip Type Splice Connector, 96" Used to cover open end of Tape Light. NATHR Mounting Clips (Pack of 15) Used to mount tape light to surface, includes mounting screws. Pack of 15 are included with every Tape Light roll (16') NATLCFC-601: Flip Type Interconnect Cable, 1" NATLCFC-603: Flip Type Interconnect Cable, 3" NATLCFC-606: Flip Type Interconnect Cable, 6" NATLCFC-612: Flip Type Interconnect Cable, 12" NATLCFC-624: Flip Type Interconnect Cable, 24" NATLCFC-648: Flip Type Interconnect Cable, 48" NATLCFC-672: Flip Type Interconnect Cable, 72" NATLCFC-696: Flip Type Interconnect Cable, 96" NATL-518: In-Line Dimmer (12V & 24V, 72W Max)

9 24V Continuous LED Tape Light Drivers & Driver Accessories NRA-125/6 NRA-125/12 NRA-125/18 NRA-125/72-6" Flexible Connector - 12" Flexible Connector - 18" Flexible Connector - 72" Flexible Connector NMT-303/24C2D1-24V, 300W (3x100W Breakers) C2 Dim. Hardwire Magn. Driver w/ Regulator for Constant Current & Voltage. Used to extend length between NUSP-JBox and NAPK-530HW/12 & NAPK-560HW/12 Can be joined together to create custom lengths. NRA-6035W/6-6' Flexible Power Cord NRA-6035W/10-10' Flexible Power Cord NATL-530HW - 24V, 30W. Class II Hardwire LED Driver. NATL-560HW - 24V, 60W. Class II Hardwire LED Driver. CONVERT TO PLUG-IN DRIVER WITH NRA-6035 Used to convert NAPK-530HW/12 & NAPK-560HW/12 into a direct plug-in driver. NUSP-JBox - Junction Box for Hardwired LED Drivers Requires NUSP-JBox for hardwiring or NRA-6035 for direct plug-in NATL V 96W Class II Plug- In Electronic LED Driver NATL V, 24W. Direct Plug-in LED Driver. NATL V, 45W. Direct Plug-in LED Driver. A: Width: 4-1/2" B: Length: 2-3/4" C: Height: 1-1/2" To be used with NAPK-530HW/12 & NAPK-560HW/12 Drivers. Capable of feeding two separate LED Drivers. Accepts Romex or flex. Includes (1) male to male connector and (1) male to female connector Power line interconnector required for 24V LED Lightbar or 24V LED Tape Light Power line interconnector required for 24V LED Lightbar or 24V LED Tape Light NATL-5100HW - 24V, 100W Class II Hardwire LED Driver includes Hardwire Box and 10' Power Line Connector. Requires NRA-6035W or NUSP-JBOX NATL-5060HW - 24V, 60W Class II Hardwire LED Driver Requires NRA-6035W or NUSP-JBOX NMTD-60/24D - Dimmable Class II Remote Hardware Magnetic Driver (60W) NMTD-96/24D - Dimmable Class II Remote Hardware Magnetic Driver (96W) Power line interconnector required for 24V LED Lightbar or 24V LED Tape Light Dimmable Class II Remote Hardwire Magnetic Driver With Integral Regulator for Constant Current and Voltage. Includes NALTL /277V