INSTALLATION INSTRUCTIONS For Light*Waves Flex II Kit with 300-Watt remote transformer
|
|
- Lisa Hopkins
- 5 years ago
- Views:
Transcription
1 IMPORTANT SAFETY INSTRUCTIONS READ ALL OF THESE BEFORE INSTALLING THE TRACK SYSTEM. SAVE THESE INSTRUCTIONS AND REFER TO THEM WHEN ADDITIONS TO OR CHANGES TO THE SYSTEM ARE MADE. THIS IS A 12-VOLT SYSTEM This track system is to be supplied by a single branch 120-Volt circuit. This track system is not intended for use with a power supply cord or convenience receptacle adaptor. Page 1 When installing or using this track system, basic safety precautions should always be followed, including the following: A) Read all instructions. B) Do not install this track in damp or wet locations. C) Do not cut any track sections. D) Do not install any part of a track system less than 5 feet above the floor. E) Use MR16 type lamps, 50-watt maximum with 300-watt transformer. F) Do not install any fixture assembly closer than 6inches from any curtain, or similar combustible material. G) Disconnect electrical power before adding to or changing the configuration of the track. H) Do not attempt to energize anything other than Flex II Track Lighting fixtures on the track. To reduce the risk of fire and electric shock, do not attempt to connect power tools, extension cords, appliances, and the like to the track. I) Do not connect a track to more than one branch circuit unless the track is constructed so that it can be used with more than one branch circuit. Check with a qualified electrician. Although the track lighting system may seem to operate acceptably, a dangerous overload of the neutral may occur and result in a risk of fire. J) If you plan to install a dimmer, do so after the Flex II system has been installed to reduce the risk of damage to the dimmer. We recommend using a Lutron magnetic low-voltage dimmer (SLV600-P). K) At least 3 fixtures need to be installed on the track before the system can be powered.
2 Page 2 Contents of this kit 10 feet of Flex II Track 5 Fixtures Remote Transformer 6 Stems 5 MR-16 Bulbs 2 Dead Ends Live Feed Transformer installation Round Canopy 1) Turn off electrical power to your house wires. For some specific information regarding this transformer, also see the instruction sheet included with the transformer. 2) Pick out a well-ventilated location for mounting your transformer. Be sure you have enough feed wiring to reach the track lighting system and the junction box, and the wiring is of the approved type (contact us if unsure about wire type). 3) Remove the cover from the top of the transformer by removing two screws and then pulling off the cover. (Figure A) 4) Insert the house wires into the transformer through the pre-cut hole and adapter, or punch out a new entry point. 5) Inside the transformer, join the white house wire with the thin white transformer wire, and the black house wire with the thin black transformer wire using wire nuts. Ensure all connections are tight. (Fig B) 5) Disconnect live feed wires from the transformer by releasing the wire nuts and screws on the adapter. (Fig C). 6) Route the live feed wires through the canopy, through the ceiling, and finally back into the transformer and tighten back the screws. Ensure there is enough live feed to reach the track. (Figure D) 7) Make sure all the connections are tight and replace the transformer cover. Unscrew Connect house wires to corresponding transformer wires using Wire Nuts. Figure A Figure B Adapter Figure C Feed Wires Live Feed Wires House Wires Figure D Feed Wires Clamp/adapter House Wires Connect house wires using clamp. Ceiling Canopy Live Feed
3 Live Feed Installation Instructions Page 3 The track is polarized and to fit with the live feed please check where the metal connectors are on the Live Feed, before you attempt to insert the Flex II track. Make sure the metal connectors are aligned properly. Live Feed with canopy Live Feed Side View Flex Trac Side View Live Feed Front View Flex Trac Front View Back Connector Live Feed Front Connector Connectors *canopy and live feed not to scale Connecting the Live Feed IMPORTANT: Disconnect electrical power before installing the live feed! Figure LF1 1) Insert the Flex II track through the opening in the live feed, making sure the metal connectors alight properly. The metal connectors on the Flex II track should touch the metal connectors on the live feed. Fig. LF1 illustrates proper insertion. Back Connector Front Connector 2) After correctly inserting the Flex II track, tighten the screws on the live feed if necessary. Live Feed Front View Live Feed Side View Flex Trac Side View 3) Ensure the live feed is mounted on the Flex II track tightly and securely. Incorrect Connection If you insert the Flex Trac the wrong way, then the metal connectors will not touch. 1 Bond Street, New York, NY Tel: Fax: ETL LISTED TRACK LIGHTING SYSTEMS Conforms To UL Std ETL TESTING LABORATORIES, INC.
4 c Page 4 Installing ceiling stems 1) Based on your desired design, determine where approximately your track will run on the ceiling. 2) A stem should hold up each end of the track, and the remaining stems should have no more than 2 feet of track between them. 3) After you have mapped the locations of the stems on your ceiling, drill a 1/8" hole and insert a plastic wall insert at each of the desired stem locations. 4) Attach the base with ceiling mount and secure with screwdriver for each hole location. (Fig A) Inserting track through stems 1) Unscrew bottom of stem mount (cap), insert track. 2) Close the stem mount by screwing the cap back on. (Fig B) Fig A Ceiling Mount Stem Fig B Stem Ceiling Track Installing the L*W C Flex II fixtures 1) When inserting the fixture make sure the metal connectors align properly. The metal connectors on the fixture should touch the metal connectors on the flex track. (Fig D) 2) Remove the cap from the fixture and place fixture on the track. 3) Replace the cap and tighten. (Fig C) Fig D Connector Connector Connector Flex Track 2 Connector Fixture Fig C
5 Changin the bulb on your Flex II Fixtures READ ALL OF THESE BEFORE INSTALLING THE TRACK SYSTEM. SAVE THESE INSTRUCTIONS AND REFER TO THEM WHEN ADDITIONS TO OR CHANGES TO THE SYSTEM ARE MADE. Page 5 Follow these instructions during first-time Flex II Track System installation, and when replacing the bulbs. Use only bulbs specified for use with your fixtures. A) Make sure the power is off B) Remember to allow the fixture and bulb enough time to cool down. C) If the fixture is installed, remove it from the track. D) Insert the pins from the MR16-type bulb into the pin holes (Fig. B1) of the fixture until the bulb is held tightly and securely in place, making sure the bulb is aligned properly (Fig B2). Do not attempt to twist the bulb and avoid bending the pins. Improper insertion may cause fixture failure. E) Mount the fixture back on the track by following the fixture mounting instructions found in the appropriate section of this instruction manual. Fig B1 Fig B2 cap Pin holes Shown here: Epsilon Interchangeable with: Alpha Delta Iota Pi Theta Zeta
6 Changin the bulb on your Flex II Fixtures READ ALL OF THESE BEFORE INSTALLING THE TRACK SYSTEM. SAVE THESE INSTRUCTIONS AND REFER TO THEM WHEN ADDITIONS TO OR CHANGES TO THE SYSTEM ARE MADE. Page 6 Follow these instructions during first-time Flex II Track System installation, and when replacing the bulbs. Use only bulbs specified for use with your fixtures. A) Make sure the power is off B) Remember to allow the fixture and bulb enough time to cool down. C) If the fixture is installed, remove it from the track. D) Insert the pins from the MR16-type bulb into the pin holes (Fig. B1) of the fixture until the bulb is held tightly and securely in place, making sure the bulb is aligned properly (Fig B2). Do not attempt to twist the bulb and avoid bending the pins. Improper insertion may cause fixture failure. E) Mount the fixture back on the track by following the fixture mounting instructions found in the appropriate section of this instruction manual. Fig B1 Fig B2 Pin Holes Shown here: Lambda Interchangeable with: Other Flex II suspension fixtures.
MONORAIL KITS INSTALLATION INSTRUCTIONS PENDANTS
MONORAIL KITS PENDANTS JESCO Lighting Group is a UL and ETL listed company Copyright 2011 JESCO Lighting Group. All rights reserved. IMPORTANT SAFETY INSTRUCTIONS Be sure to read and unsderstand the following
More informationINSTALLATION INSTRUCTION W Track Recessed 120V Flangeless
W Track Recessed 120V Flangeless WT4-RTL, WT8-RTL, WT12-RTL SAFETY INSTRUCTION Read all of these instructions before installing the track system. Turn off power at main switch before installing or modifying
More informationIMPORTANT SAFETY INSTRUCTIONS
INSTALLATION INSTRUCTIONS READ ALL OF THESE INSTALLATION INSTRUCTIONS BEFORE INSTALLING THE TRACK SYSTEM SAVE THESE INSTRUCTIONS AND REFER TO THEM WHEN ADDITIONS TO OR CHANGES IN THE TRACK CONFIGURATION
More informationMONORAIL KITS INSTALLATION INSTRUCTIONS SPOTS
MONORAIL KITS INSTALLATION INSTRUCTIONS SPOTS JESCO Lighting Group is a UL and ETL listed company Copyright 2011 JESCO Lighting Group. All rights reserved. IMPORTANT SAFETY INSTRUCTIONS Be sure to read
More informationINSTALLATION INSTRUCTION W Track Suspension system
SAFETY INSTRUCTIONS: - Suspension mounting system should be installed by a qualified electrician only. - System is intended for installation in accordance with National Electric Code, local and - Federal
More informationWARNING NORDIC ALUMINIUM LIGHTING TRACK SYSTEMS
WARNING NORDIC ALUMINIUM LIGHTING TRACK SYSTEMS DO NOT solder connectors as this will prohibit the adapters circuit switch to move freely from circuit to circuit. Nordic Aluminium track adapters and accessories
More informationSURFACE TRACK (120/250V) SPECIFICATIONS
SURFACE TRACK (120/250V) SPECIFICATIONS GENERAL Lighting Track shall allow fixtures to be located anywhere along the track length. Fixtures shall be easily focused, switched, dimmed, accessorized and removed
More informationINTEGRID TRACK (120V) SPECIFICATIONS
INTEGRID TRACK (120V) SPECIFICATIONS GENERAL Integrid Track shall be a combination Track and main runner for mech - anically supporting suspended ceiling systems. Integrid Track shall allow fixtures to
More informationInstallation Instructions for Monorail 2 Circuit 2 X 250 Watt Sloped Surface Mount Magnetic Transformer 120 Volt Input to 12 Volt Single Feed Output
0 Edge Lighting. All Rights Reserved. 78 W. Fullerton Ave Chicago, IL 0 Tel: 77-770-9 Fax: 77-9- www.edgelighting.com info@edgelighting.com MT-X0--SL_ 90-MT-X0--SL-0 Installation Instructions for Monorail
More informationMOUNTING SYSTEMS SPECIFICATIONS
MOUNTING SYSTEMS SPECIFICATIONS GENERAL Mounting Systems shall allow Track Systems to be fastened to or from various surfaces in a wide range of safe and approved methods. Mounting Systems shall have a
More informationINSTRUCTION MANUAL SINKER. By HAY
INSTRUCTION MANUAL SINKER By HAY INTRODUCTION An elemental looking light available as either a small or large pendant. The fabric cord comes with a magnetic moulded ceiling cap in a textured finish. The
More informationTwo Circuit Trac System TRAC SECTION, JOINERS & FEEDS
Project: Fixture Type: Location: Contact/Phone: PRODUCT DESCRIPTION DIMENSIONS Low profile, two-circuit trac sections for surface or pendant mounting. Provides two separate 20-amp circuits from a single
More informationAssembly instruction. Pendant Light Toccata GENERAL REMARKS ON SAFETY: Technical data: BOM
GENERAL REMARKS ON SAFETY: Read all of these instructions before installing fixtures. Keep all of the instructions for future reference. Turn off power before installing fixture. Installation is to be
More informationNT-300 Series Single Circuit Track System & Accessories
NT-300 Series Single Circuit Track System & Accessories Type Project Catalog No. Lamp/Wattage PRODUCT DESCRIPTION Low profile, extruded aluminum track with 20-Amp rated flat, solid integral copper conductors.
More information12V Track System. Metal Glass Pendant. 12V Track Lighting Systems. Versatile low voltage lighting system with flexible track, ceiling or wall mounted
Track Lighting Systems Track System Metal Glass Pendant Versatile low voltage lighting system with flexible track, ceiling or wall mounted ETL Listed TRACK LIGHTING 109965 SYSTEM Conforms to UL Std. 1574
More informationInstallation Instruction
T F W 604.549.9379 604.549.9555 fluxwerx.com Installation Instruction DRIVER ENCLOSURE Ceiling Type Version Grid Battery Pack GRID MOUNT INSTALL OPTIONS OPTION 1: Standard Vertical Grid drivers can be
More informationINSTALLATION AND OPERATING INSTRUCTIONS
INSTALLATION AND OPERATING INSTRUCTIONS MANUAL TRANSFER SWITCHES FROM 0 Residential Wattage Requirements Appliance Running Watts Add watts for starting Furnace blower, gas or fuel 1/8 hp 300 500 1/8 hp
More informationTwo Circuit Trac System TRAC SECTION, JOINERS & FEEDS
Project: Fixture Type: Location: Contact/Phone: PRODUCT DESCRIPTION DIMENSIONS Low-Profile, two-circuit trac sections for surface or pendant mounting. Provides two separate 20-amp circuits from a single
More informationInstallation Manual. CS9300 Professional Series Landscape Lighting System
Installation Manual CS9300 Professional Series Landscape Lighting System CS9300 Professional Series Landscape Lighting System pg. 1 READ THESE INSTRUCTIONS ENTIRELY BEFORE BEGINNING INSTALLATION! Congratulations
More informationMIDTOWN INSTRUCTIONS. White, Silver, Black. Single Light. MIDTOWN LED Recessed Light Installation Guide LED RECESSED LIGHT. (The nuts & bolts)
Single Light (The nuts & bolts) White, Silver, Black LED Recessed Light Installation Guide To avoid electric shock, disconnect the power to your ceiling fixture prior to installation.. Make sure the power
More informationTRAC-LITES One Circuit Trac System TRAC SECTIONS & SYSTEM COMPONENTS R Series
Project: Fixture Type: Location: Contact/Phone: PRODUCT DESCRIPTION DIMENSIONS Reduced-profile, single-circuit trac sections for surface or pendant mounting. Compatible with a full range of feed, connector
More informationOne Circuit Trac System TRAC SECTION, JOINERS & FEEDS T Series
Project: Fixture Type: Location: Contact/Phone: PRODUCT DESCRIPTION DIMENSIONS Low-Profile, single-circuit trac sections for surface or pendant mounting. I-beam cross section provides added strength and
More information12 INCH WAREHOUSE BARN PENDANT LIGHT
12 INCH WAREHOUSE BARN PENDANT LIGHT OWNER S MANUAL WARNING: Read carefully and understand all ASSEMBLY AND OPERATION INSTRUCTIONS before operating. Failure to follow the safety rules and other basic safety
More informationModel (Circuit Tester) Model (GFCI Tester)
User Manual 99 Washington Street Melrose, MA 02176 Phone 781-665-1400 Toll Free 1-800-517-8431 Visit us at www.testequipmentdepot.com Receptacle Testers Model 20250-61 (Circuit Tester) Model 20250-62 (GFCI
More informationInstallation Manual CS9300-LED. Professional Series Landscape Lighting System
Installation Manual CS9300-LED Professional Series Landscape Lighting System CS9300 Professional Series LED Landscape Lighting System pg. 1 READ THESE INSTRUCTIONS ENTIRELY BEFORE BEGINNING INSTALLATION!
More informationOne Circuit Trac System TRAC SECTION, JOINERS & FEEDS T Series
Project: Fixture Type: Location: Contact/Phone: PRODUCT DESCRIPTION DIMENSIONS Low-Profile, single-circuit trac sections for surface or pendant mounting. I-beam cross section provides added strength and
More informationRECESSED TRACK (120V) SPECIFICATIONS
RECESSED TRACK (120V) SPECIFICATIONS GENERAL Recessed track shall be approved by the NEC for flush-mounting into ceiling or any flat surface. Recessed Track shall allow fixtures to be easily focused, switched,
More informationEMERY SKY SUSPENDED LED LUMINAIRE
EMERY SKY SUSPENDED LED LUMINAIRE IP20 DRY LOCATION 120V- 277V AC SAFETY & WARNINGS 1. READ AND FOLLOW ALL SAFETY INSTRUCTIONS 2. Install in accordance with national and local electrical code regulations.
More informationEasy/Tran TF STANDBY POWER FURNACE SWITCH TOOLS NEEDED FOR INSTALLATION. PARTS LIST for Easy / Tran TF FURNACE TRANSFER SWITCH
STANDBY POWER FURNACE SWITCH Easy/Tran TF Congratulations on your purchase of the Reliance Controls Easy/Tran TF furnace transfer switch. Reliance has been manufacturing transfer switches and equipment
More informationJuno Trac-Master Trac Lighting Systems. Comprehensive line and low voltage track systems
Juno Trac-Master Trac Lighting Systems Comprehensive line and low voltage track systems Juno Trac-Master System Safe and simple installation is what you can expect from Juno one-circuit and two-circuit
More informationElectrical Safety. Electrical Safety Webinar. Electrical. Printing Industries Alliance Printing Industries Alliance 1
Webinar 1 Electrical 2 1 Webinar Introduction An average of one worker is electrocuted on the job every day There are four main types of electrical injuries: Electrocution (death due to electrical shock)
More informationpoollux Power plx-pw60 & plx-pw100
poollux Power plx-pw60 & plx-pw100 ETL LISTED Conforms to UL STD 379; Certifi.ed.to.CSA.STD.C22.2.#218.1 5005508 Installation Instructions Read all instructions before attempting to perform installation
More informationASSEMBLY INSTRUCTIONS PRODUCT CODE: CAUTION: Carefully Read Instructions and Procedures for Safe Operation. 7' Diamond Peak LED Tree
7' Diamond Peak LED Tree ASSEMBLY INSTRUCTIONS MODEL NO: U11G684A-024-01 (WL-019) PRODUCT CODE: 140-034067-090 CAUTION: Carefully Read Instructions and Procedures for Safe Operation. Receipt of Purchase:
More informationRaritan PX. Power Cord Installation Guide. Safety Guidelines. Safety Instructions
QS Rule Raritan PX Power Cord Installation Guide This installation guide explains how to install power cords on Raritan PX products that do not come with a factory installed power cord. This type of product,
More informationGEMINI HOUSING SPECIFICATIONS
GEMINI HOUSING SPECIFICATIONS GENERAL Gemini Housing shall support Track of six foot intervals. In addition, the extra compartment shall be able to be used for a multitude of elec trical or mechanical
More informationCONTENT VIPP LAMPS : TIMELESS ILLUMINATION 4-5 IMPORTANT SAFETY INSTRUCTIONS 6-8 VIPP521 TABLE LAMP VIPP522 WALL LAMP 16-23
VIPP521-526 LAMPS 1 CONTENT VIPP LAMPS : TIMELESS ILLUMINATION 4-5 IMPORTANT SAFETY INSTRUCTIONS 6-8 VIPP521 TABLE LAMP 10-15 VIPP522 WALL LAMP 16-23 VIPP524 WALL SPOT 24-31 VIPP525 FLOOR LAMP 32-41 VIPP526
More informationInstruction/Installation Manual
Instruction/Installation Manual Retrofit:LED Tube Lamp 4ft. Fluorescent T8/T10 Replacement 1 SECTION 1 - General Information Kit components:1-led Tube, 1-Label and 1-Set of Instructions Models were only
More informationInstallation Instruction ALG Series LED Area Light Version: 3.1
IMPORTANT SAFETY INSTRUCTIONS READ CAREFULLY BEFORE INSTALLING THE FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE. To reduce the risk of death, personal injury or property damage from fire, electric
More informationSURFACE CONTROLTrack SPECIFICATIONS
CONTROLTrack SURFACE CONTROLTrack SPECIFICATIONS GENERAL CONTROLTrack shall allow fixtures to be located anywhere along the track length. Fixtures shall be easily focused, switched, dimmed, accessorized
More informationELECTRICAL. 60 Minutes
ELECTRICAL 60 Minutes AGENDA Electrical definitions Electrical shocks, burns and secondary injuries Electrical hazards in the workplace Safety devices and prevention steps Do s and Don ts INTRODUCTORY
More informationUV8 & UV90 SERIES INSTALLATION INSTRUCTIONS
UV8 & UV90 SERIES INSTALLATION INSTRUCTIONS Important THIS SHEET CONTAINS IMPORTANT SAFETY INSTRUCTIONS. SAVE THESE INSTRUCTIONS. Warning This product must be installed in accordance with National Electrical
More informationLumeLEX 2084 SERIES INSTALLATION INSTRUCTIONS THIS SHEET CONTAINS IMPORTANT SAFETY INSTRUCTIONS. SAVE THESE INSTRUCTIONS.
LumeLEX 2084 SERIES INSTALLATION INSTRUCTIONS Important THIS SHEET CONTAINS IMPORTANT SAFETY INSTRUCTIONS. SAVE THESE INSTRUCTIONS. Warning This product must be installed in accordance with National Electrical
More informationINSTRUCTION MANUAL. IMPORTANT SAFEGUARDS When using electrical equipment, basic safety precautions should always be followed, including the following:
IMPORTANT SAFEGUARDS When using electrical equipment, basic safety precautions should always be followed, including the following: READ AND FOLLOW ALL SAFETY INSTRUCTIONS 1. CAUTION To prevent electrical
More informationASSEMBLY INSTRUCTIONS
6.5' McKinley Pine ASSEMBLY INSTRUCTIONS MODEL NO: U11G681A-024-01 (WL-018) PRODUCT CODE: 140-034066-910 CAUTION: Carefully Read Instructions and Procedures for Safe Operation Receipt of Purchase: Questions,
More informationAn average of one worker is electrocuted on the job every day There are four main types of electrical injuries:
Electrical Safety Introduction An average of one worker is electrocuted on the job every day There are four main types of electrical injuries: Electrocution (death due to electrical shock) Electrical shock
More informationOUTPUT CONNECTIONS Bring the wires of the light fixture through the other open knockout and connect them to the power supply output wires.
MAGNETIC SUPPLY INSTALLATION SAFETY GUIDE Please read before installing. GENERAL This power supply is to be installed in accordance with Article 450 of the National Electric Code. The power supply must
More information1718 W. Fullerton Ave Chicago, IL Tel: Fax:
206 Edge Lighting. All Rights Reserved. Installation Instructions for Nova Power Suspension Up/Down - Center Feed Glide Up/Down - Center Feed IMPORTANT INFORMATION - This product is suitable for indoor
More informationASSEMBLY AND INSTALLATION INSTRUCTIONS
ASSEMBLY AND INSTALLATION INSTRUCTIONS 348-0035 / 348-0036 WARNING: TO AVOID RISK OF ELECTRICAL SHOCK, BE SURE TO SHUT OFF POWER BEFORE INSTALLING OR SERVICING THIS FIXTURE. NOTES: 1. Before installing,
More informationMaxLite LED Enclosed & Sealed Jelly Jars
General Safety Information To reduce the risk of death, personal injury or property damage from fire, electric shock, falling parts, cuts/abrasions, and other hazards read all warnings and instructions
More informationWARNING. Important Notice
CAL (Color AquaLuminator ) Light and Return Water Flow for Above Ground Pools Owners Manual IMPORTANT SAFETY INSTRUCTIONS READ AND FOLLOW ALL INSTRUCTIONS SAVE THESE INSTRUCTIONS Table of Contents SECTION
More informationInstallation Guide DO NOT CUT WIRES
Installation Guide LED INFO & WARNINGS Please read and comprehend the entire manual before attempting to assemble, operate, or install the product. Make sure that you have all necessary parts by checking
More informationIMPORTANT SAFETY INSTRUCTIONS READ AND FOLLOW ALL INSTRUCTIONS SAVE THESE INSTRUCTIONS
AQUALUMINATOR & AQL LIGHT AND RETURN WATER FLOW FOR ABOVE GROUND SWIMMING POOLS INSTALLATION AND USER'S GUIDE Contents SECTION I. IMPORTANT SAFETY INSTRUCTIONS... 2 SECTION II. LAMP HOUSING INSTALLATION...
More informationThe lever must be placed at the lower position, when the track head is intended to be use in a one-circuit track system.
1-CIRCUIT TRACK Single circuit Extruded aluminum body Insulated solid 12-gauge copper Rated for maximum of 2400 watts Visual polarity groove Compatible with most 3-wire systems ET2 ET4 ET6 ET8 ET12 2 FT.
More informationINDUSTRY WIDE LABOR-MANAGEMENT SAFETY COMMITTEE
INDUSTRY WIDE LABOR-MANAGEMENT SAFETY COMMITTEE SAFETY BULLETIN #23 GUIDELINES FOR WORKING WITH LIGHTING SYSTEMS AND OTHER ELECTRICAL EQUIPMENT All electrical systems and electrically energized equipment
More informationArnberg Industries & It s Partners are not responsible for any damage or injury caused by correct or incorrect installation of this transfer switch.
3560 NE ROZENE WAY BREMERTON, WASHINGTON 98311 (530) 316-1049 Generator Transfer Switch Model; HTS15-MAN & HTS15-MAN-2 Tools Needed For Installation Power drill Wire stripper and cutter (10 to 14 gauge)
More informationWireless Dimmer Installation and User Guide
Installation Instructions Supported Models and Fixtures Wireless Dimmer Installation and User Guide This installation and user guide covers these dimmer models: LDZ-101-W Wireless Dimmer (802.15.4) LDZ-101-B
More informationInstallation Instructions: Eco Linear High Bay
Installation Instructions: Eco Linear High Bay Installation Notes & Precautions: Read all precautions, warnings, instructions contained in this document. These instructions can be used to install Eco Linear
More information5.5 FT PRE-LIT SERBIAN SPRUCE TREE
ITEM #0674086 Holiday Living & Design is a registered trademark of LF, LLC. All Rights Reserved. 5.5 FT PRE-LIT SERBIAN SPRUCE TREE MODEL #W14D0225 Español p. 8 ATTACH YOUR RECEIPT HERE Serial Number Purchase
More information7.5 FT PRE-LIT ENGLEWOOD PINE TREE
ITEM #0243778 7.5 FT PRE-LIT ENGLEWOOD PINE TREE Holiday Living & Design is a registered trademark of LF, LLC. All Rights Reserved. MODEL #W14L030 Español p. 11 ATTACH YOUR RECEIPT HERE Serial Number Purchase
More informationINSTALLATION INSTRUCTION MANUAL
INSTALLATION INSTRUCTION MANUAL LED FLOOD LIGHT, 100-277VAC MODELS: SL923FLF-15W; SL923FLF-30W; SL923FLF-50W; SL923FLF-80W; SL923FLF-100W; SL923FLF-150W; SL923FLF-300W Model number parameter list: Model
More informationHPNLS-HO. Installation Manual
Installation Manual WARNING: Do not lift fixture by cables. This could result in permanent damage to both the fixture and the cables. Damage resulting from grasping cables and/or putting undue pressure
More informationWALL-MOUNT SCONCE LIGHT OWNER S MANUAL
WALL-MOUNT SCONCE LIGHT OWNER S MANUAL WARNING: Read carefully and understand all ASSEMBLY AND OPERATION INSTRUCTIONS before operating. Failure to follow the safety rules and other basic safety precautions
More informationUSE AND CARE GUIDE 15 INCH WHITE ROUND FLAT PANEL FIXTURE WITH SELECTABLE COLOR TEMPERATURE
74212 USE AND CARE GUIDE 15 INCH WHITE ROUND FLAT PANEL FIXTURE WITH SELECTABLE COLOR TEMPERATURE FEIT ELECTRIC COMPANY PICO RIVERA, CA (800) 543-3348 FAX (562) 908-6360 www.feit.com Table of Contents
More informationLED Garage Light INSTALLATION INSTRUCTIONS. *Model number noted on carton label
LED Garage Light *Model number noted on carton label INSTALLATION INSTRUCTIONS Model Number / Número de Modelo / Numéro des modèle SGLL 24 PIR (24 LED Garage Light) Actual Dimensions 10 W x 3-1/2 H x 24-1/2
More informationINSTALLATION INSTRUCTIONS SUPERPLANE 2.5. Suspended. A nd Avenue, Unit 1 Oakland, CA P E W alwusa.
INSTALLATION INSTRUCTIONS SUPERPLANE 2.5 Suspended A 1035 22nd Avenue, Unit 1 Oakland, CA 94606 P 510.489.2530 E TalkToUs@alwusa.com W alwusa.com SP2.5S - Safety & Warnings! 1. Read all instructions. 2.
More informationNORTHSTAR 154 BATH/SPA TV. Installation Instructions
NORTHSTAR 154 BATH/SPA TV Installation Instructions IMPORTANT SAFETY INSTRUCTIONS Must be installed by a qualified electrician Read these instructions. Keep these instructions for future use. Install in
More informationOWNER S MANUAL AND INSTALLATION INSTRUCTIONS
EmerGen Switch Manual Transfer Switch OWNER S MANUAL AND INSTALLATION INSTRUCTIONS For A Series Models 6-5001, 6-7501, 10-7501, 10-12K1 PLEASE READ THIS MANUAL IN ITS ENTIRETY BEFORE INSTALLING AND/OR
More informationAquaLumin III - Nicheless Light Installation Guide IMPORTANT SAFETY INSTRUCTIONS READ AND FOLLOW ALL INSTRUCTIONS SAVE THESE INSTRUCTIONS
16 1 AquaLumin III - Nicheless Light Installation Guide IMPORTANT SAFETY INSTRUCTIONS READ AND FOLLOW ALL INSTRUCTIONS SAVE THESE INSTRUCTIONS Section Contents 1. Installing a mounting bracket and light
More informationPIL0478 ISSUE 01/ 07/16
ISSUE 01/ 07/16 PIL0478 ZAFIR G9 CEILING FITTING PIL0478 ISSUE 01/ 07/16 PART C PART E PART 21 SELV 1 1.B 1 3.1 3.3 3.4 3.5 3.6, 3.8 3.10 3.12 3.14 3.16 3.17 3.18 3.19 3.19 ATTENTION! THE TABLE BELOW
More informationMEDIA LED. Pendant Standard Mount Installation ou de montage WARNING:
MEDIA LED Pendant Standard Mount WARNING: Disconnect main power at the source prior to installation! Thread gripper base onto 1 /4 20 stud, or with #8 screw. Depress gripper nozzle to insert aircraft cable.
More informationStrip Fixture URS Light Bar Retrofit Installation Instructions Revised:
Strip Fixture URS Light Bar Retrofit Installation Instructions Revised: 20180126 These instructions do not purport to cover all details or variations in components nor to provide for every possible contingency
More informationOutdoor Installation Using an Electronic LED Power Supply (TE-60L-12)
0 Edge Lighting. All Rights Reserved. 78 W. Fullerton Ave Chicago, IL 606 Tel: 77-770-9 Fax: 77-9-6 www.edgelighting.com info@edgelighting.com Installation Instructions for Port Round & Square LED PORT-RD-ST-SA
More informationASSEMBLY INSTRUCTIONS
A Canopy Assembly and wired by Licensed Electrician 1. Fixture Stud must be affixed to Electrical Box 2. Insert Nipple into Hickey 3. Slide Glass Canopy onto Nipple and secure with Hanger Loop with Washer.
More informationInstallation Manual CS9100-LED. Professional Series Landscape Lighting System
Installation Manual CS9100-LED Professional Series Landscape Lighting System LED Landscape Lighting System pg. 1 READ THESE INSTRUCTIONS ENTIRELY BEFORE BEGINNING INSTALLATION! Congratulations on your
More informationMASTERsine Inverter PXA Series Installation Guide
Backup Power System Expert TM MASTERsine Inverter PXA Series Installation Guide Important Safety Instructions IMPORTANT: Read and save this Installation Guide for future reference. This chapter contains
More informationInstruction Manual. H.I.D Digital Ballasts 400W 600W 1000W. All our ballasts are compatible with Safe Grow Hydroponic Smart System.
Instruction Manual H.I.D Digital Ballasts 400W 600W 1000W All our ballasts are compatible with Safe Grow Hydroponic Smart System. IMPORTANT PRODUCT INFORMATION READ IMMEDIATELY SAFETY FIRST! Failure to
More informationTechnical Information Guide
Revised 09/1/08 Technical Information Guide www.sunlightsupply.com www.nationalgardenwholesale.com IMPORTANT PRODUCT INFORMATION READ IMMEDIATELY KEEP ORIGINAL PACKAGING ALL RETURNS NEED TO BE IN THE ORIGINAL
More information3. Please ensure the electricity connections conform to the National Electrical Code and local regulations if applicable.
FLUORESCENT EMERGENCY BALLAST WARNING: When using this lighting device, safety precautions should be followed at all times. CAUTION: Verify that all replacement lamp types marked on the installed luminaire
More informationINSTALLATION INSTRUCTIONS RECESSED EXTRUSIONS WITH LED TAPE
LLI-XR-CRV LLI-XR-ELF LLI-XR-IFL LLI-XR-IGR LLI-XR-SQF LLI-XR-THF **DANGER: Prior to installation, disconnect power at the source.** Make sure you have all components listed below: LED tape 24VDC Power
More information9' Warm White /Multi LED Color Changing M5 One Plug tree V INSTRUCTION MANUAL
9' Warm White /Multi LED Color Changing M5 One Plug tree V64886-60 INSTRUCTION MANUAL Thank you for purchasing a SYLVANIA Pre-lighted Tree. This tree assembles in minutes and is decorated with energy saving
More informationRECHARGEABLE SPOTLIGHT
RECHARGEABLE SPOTLIGHT MODEL: RWL10 Part No: 4002822 INSTRUCTION MANUAL LS0609 INTRODUCTION Thank you for purchasing this CLARKE product Before attempting to use the product, it is essential that you read
More informationChapter 4 Utility Systems Electrical
Chapter 4 Utility Systems Electrical Utility Systems Electrical The electrical supply to your home begins outside, where you will see either an overhead feed and piping down the side of your home or (if
More informationCONTENTS DESCRIPTION UNPACKING DIMENSIONS
INSTALLATION INSTRUCTIONS Recessed Luminaire ModelNo.FV-NLF6RES CONTENTS GENERAL SAFETY INFORMATION DESCRIPTION UNPACKING SUPPLIED ACCESSORIES DIMENSIONS WIRING DIAGRAM INSTALLATION (BETWEEN JOISTS MOUNTING)
More informationPower Supply Recommendations
Power Supply ecommendations 24V PLUG-IN POWE SUPPLY ecommended Fixtures with barrel connector ends (non-dimmable) 690010.004 30W Plug-in wall wart power supply 69TL0117 90W Mean Well Plug-in power supply
More informationAEROBAY INSTALLATION INSTRUCTIONS
AEROBAY INSTALLATION INSTRUCTIONS AEROBAY IMPORTANT READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE. Fixtures must be wired in accordance with the National Electrical
More informationINSTALLATION, OPERATION AND MAINTENANCE INSTRUCTIONS FOR NEW YORK 18 WATT SERIES
INSTALLATION, OPERATION AND MAINTENANCE INSTRUCTIONS FOR NEW YORK 18 WATT SERIES IMPORTANT SAFEGUARDS When using electrical equipment, basic safety precautions should always be followed including the following:
More informationInstallation Instructions
LENNON 3 LIGHT PENDANT SKU# 039010, 039013 Rated Voltage 220-240V~ 50Hz Thank you for purchasing this quality Lucci product. To ensure correct function and safety, please read and follow all instructions
More informationElectric Vehicle Charging Station
EVoReel Electric Vehicle Charging Station INSTALLATION GUIDE AND USER MANUAL Model: Dual Output Pedestal Mount 30A EVoReel EVSE Model Numbers: With Basic EVSE: EV072-400-002A; With Intelligent ievse: EV072-410-002A;
More informationMOONRING 1.5 MOONRING 3
INSTALLATION INSTRUCTIONS MOONRING 1.5 MOONRING 3 MR1.5 & MR3 Suspended, Ceiling LED n A 1035 22nd Avenue, Unit 1 Oakland, CA 94606 P 510.489.2530 E TalkToUs@alwusa.com W alwusa.com Safety & Warnings!
More informationInstallation Instructions
QUINN 6 LIGHT PENDANT SKU# 039019, 039020 Rated Voltage 220-240V~ 50Hz Thank you for purchasing this quality Lucci product. To ensure correct function and safety, please read and follow all instructions
More informationDemand Switch NEFA20 Plus. Installation Guide. Please read this entire guide before beginning the installation!
Demand Switch NEFA20 Plus Installation Guide Please read this entire guide before beginning the installation! Supplied Parts Protective Covers DIN Mounting Rail NEFA20 Plus Mounting Rail Spacer Warning
More informationFIXTURE INSTALLATION GUIDE Model T21T (Low Voltage Pendant Set 120V)
FIXTURE INSTALLATION GUIDE Model T21T (Low Voltage Pendant Set 120V) 21T, Rev.4 6-13 IMPORTANT: Before proceeding, retrieve the GLASS SHADE INSTALLATION GUIDE, which is included with the pendant cord set
More informationHEAVY DUTY BATTERY BOOSTERS / CHARGER MODEL No. BC420N
HEAVY DUTY BATTERY BOOSTERS / CHARGER MODEL No. BC420N OPERATING & MAINTENANCE INSTRUCTIONS 1206 SPECIFICATIONS Supply Voltage 230 Max Charge (Amps) 60 (cont) Max Boost (Amps) 400 Boost/Charge (Volts)
More informationLED 2/3/4ft T8 Tube 120V
E-T8-1200-YR LED 2/3/4ft T8 Tube 120 Our LED Tubes utilize the latest LED chips as the light source, whilst using the standard T8 end caps, which makes it easy to install and replace traditional fluorescent
More informationGavita HortiStar 600 SE EU
Pro line Gavita HortiStar 600 SE EU Horticultural design HortiStar 600 HR 96 reflector Reflector efficiency 96 % Easily replaceable reflector Shielded cord terminal For HPS/MH lamps up to 750 W Gavita
More informationLED Downlight Ceiling Fixtures
ED Downlight Ceiling Fixtures Every attempt has been made to ensure that this documentation is as accurate and up-to-date as possible. However, Vertical Express assumes no liability for consequences, directly
More informationULTRA PERFORMANCE LED TUBE INSTALLATION INSTRUCTIONS
Ultra Performance LED Tube Installation Instructions Page 1 of 7 ULTRA PERFORMANCE LED TUBE INSTALLATION INSTRUCTIONS These instructions do not purport to cover all details or variations in components
More informationINSTALLATION INSTRUCTIONS LIGHTPLANE 3.5. LP3.5 Suspended LED. A nd Avenue, Unit 1. CA P E W alwusa.
Oakland, INSTALLATION INSTRUCTIONS LIGHTPLANE 3.5 LP3.5 Suspended LED A 1035 22nd Avenue, Unit 1 n CA 94606 P 510.489.2530 E TalkToUs@alwusa.com W alwusa.com Safety & Warnings! 1. Read all instructions.
More informationMeasurements are expressed in millimeters.
T-Rex user manual Measurements are expressed in millimeters. 1 Lamp access 2 Focus adjustment 3 Mounting bracket 4 Swivel locks 5 Clamp hole 6 Air vent 190 285 7 AC input & main fuse 8 Microphone 490 164
More information16 INCH WAREHOUSE BARN LIGHT OWNER S MANUAL
16 INCH WAREHOUSE BARN LIGHT OWNER S MANUAL WARNING: Read carefully and understand all ASSEMBLY AND OPERATION INSTRUCTIONS before operating. Failure to follow the safety rules and other basic safety precautions
More information