solenoids & relays solenoids & relays

Size: px

Start display at page:

Download "solenoids & relays solenoids & relays"

Kenneth Bryant
6 years ago
Views:

H STEEL & PHENOLIC BODY SOLENOIDS PVC COATED SOLENOIDS WITH STEEL HOUSINGS PLASTIC BODY SOLENOIDS MODULES RELAYS INFORMATION ON SOLENOIDS H H H H4 H5 H6 H STEEL & PHENOLIC BODY SOLENOIDS Continuous

1 H STEEL & PHENOLIC BODY SOLENOIDS PVC COATED SOLENOIDS WITH STEEL HOUSINGS PLASTIC BODY SOLENOIDS MODULES RELAYS INFORMATION ON SOLENOIDS H H H H4 H5 H6 H STEEL & PHENOLIC BODY SOLENOIDS Continuous Duty A except where noted. Normally Open Contacts, SPST, One circuit: Off - On Housings: Plated steel (Phenolic where noted). Contacts: Copper 5/6" -4 thread, hexnuts and lockwashers included. 00A solenoids have silver contacts. Coil, ignition and ground terminals: Steel 0- thread, hexnuts and lockwashers included. Bracket mounting holes 5/6" x 9/" (7.9 x 5.) on /64" centers (56.0mm). 4V Insulated Also available in Plastic Body (section H): V Insulated 4080 PVC coated and UL-rated model: see PVC coated model: see A UL-Listed Same as 4080, but UL and CE rated. Continuous Rating: 65A at 6V DC. Intermittent rating: 0A make, 65A break. 0 sec On, 0 min Off. MARINE LISTED Electrical Rating: 00A carry only. Not to break 00A at 4V DC. Silver contacts. Cole Hersee Co. 0 Old Colony Ave, Boston, MA T F

H H STEEL & PHENOLIC BODY SOLENOIDS 4V Grounded 44 440 Normally On V Insulated 45 Continuous Duty 5A. V Grounded Also available in Plastic Body (section H): 46-G0.

2 H H STEEL & PHENOLIC BODY SOLENOIDS 4V Grounded Normally On V Insulated 45 Continuous Duty 5A. V Grounded Also available in Plastic Body (section H): 46-G BP BP 408 Curved Bracket PVC coated model: see UL Listed BP Same as 4059, but UL and CE rated. Continuous Rating: 65A at V DC. Intermittent rating: 750A make, 00A break. 0 sec On, 0 min Off. Circuit G. PVC coated model: see 47-0 MARINE LISTED 6V 4097 Insulated 44 00A Electrical Rating: 00A. Silver contacts. Cole Hersee Co. 0 Old Colony Ave, Boston, MA T F

Continuous Duty, Normally Closed contacts 5A, Normally Open contacts A. 4400 6V Insulated Latching Solenoid V Continuous Duty, 0A (carry only). Insulated. Plated steel housing.

3 H STEEL & PHENOLIC BODY SOLENOIDS H Two Circuits, DPST Normally Off and Normally On. Special application: for forward and reverse systems in electric golf carts, garden tractors, fork lift trucks, winches, etc. Housing: Steel. Continuous Duty, Normally Closed contacts 5A, Normally Open contacts A V Insulated Latching Solenoid V Continuous Duty, 0A (carry only). Insulated. Plated steel housing. Requires only a momentary application of coil power to operate. Very little heat is generated, because the coil is de-energized when the solenoid is On. 400 Momentary Switch BAT LOAD 440 4V Insulated Schematic and picture same as V Insulated Schematic and picture same as PVC coated model: see V Grounded The Latching Solenoid This special solenoid toggles On and Off, and requires no current to maintain the continuity of the power circuit. Use it with a momentary switch (see Momentary Switches). Actuation of the momentary switch causes current to flow in the solenoid coil, locking the contact in place, maintaining the load circuit in an On position. A second actuation of the momentary switch releases the plunger, turning the load circuit Off. Suggested momentary switches: 5507, Special Applications See page 8. Motor Reversing Typical DC series wound permanent magnet circuit, using a pair of double-action solenoids. Use pairs of the following solenoids: 440 (V), 440 (4V), or 4400 (6V). SPDT Control Switch Fwd Rev 440X Series Solenoid 440X Series Solenoid 4 4 To Motor To Motor Cole Hersee Co. 0 Old Colony Ave, Boston, MA T F

4 H H STEEL & PHENOLIC BODY SOLENOIDS Intermittent Duty Normally Off, SPST, One circuit: Off - On 750A make, 00A break, 0sec On, 0min Off, except where noted. Contacts: Copper. Terminals: Copper. Small ignition and ground terminals are 0- thread. Large contact terminals are 5/6" -4 thread. Hexnuts and lockwashers are included. Bracket mounting holes 5/6 x 9/, /64" on centers (7.9 x 5., 56.0mm) and plated steel housing, except where noted. 4V Insulated 0A make, 65A break. 0 sec On, 0 min Off , Curved Bracket 40 Phenolic Housing Bracket mounting holes 9/" x 5/64, 7/64" on centers (7. x 9.9, 5.6mm). 404 V Grounded Also available in Plastic Body (section H): 47-GS7. V Grounded, Resistor Shorting Circuit In this application, is Normally Open. It becomes common with and 4 when the solenoid is energized. Commonly used in engine starting applications. 40 RESISTOR SHORTING CIRCUIT 407 PVC coated model: see Phenolic Housing Bracket mounting holes 9/ x /, /64" on centers (7. x.7, 56.0mm). Contact terminal 5/6" -4 thread. M-0 Marine Marine construction. Clear protective finish, brass hexnuts and lockwashers. Cole Hersee Co. 0 Old Colony Ave, Boston, MA T F

5 H STEEL & PHENOLIC BODY SOLENOIDS H V Insulated Also available in Plastic Body (page 77) PVC coated model: Phenolic Housing 6V Grounded 404 M-00 Marine BP Same as 4047, but marine construction. Clear protective finish, brass hexnuts and lockwashers. M-00-0 Marine, UL Listed Same as M-00, but with UL & CE listing. Intermittent rating: 750A make, 00A break. 0 sec On, 0 min Off. MARINE LISTED 409 Curved Bracket PVC coated model: 4077 Electronic Solenoid See page Phenolic Housing Bracket mounting holes 5/6" x 9/, 9/6" on centers (8. x 7., 65.mm). Cole Hersee Co. 0 Old Colony Ave, Boston, MA T F

H H PVC COATED SOLENOIDS WITH STEEL HOUSING Weatherproof: Housing is completely PVC coated. Continuous Duty Insulated SPST, Normally Off (except 440-04). One circuit: Off - On.

6 H H PVC COATED SOLENOIDS WITH STEEL HOUSING Weatherproof: Housing is completely PVC coated. Continuous Duty Insulated SPST, Normally Off (except ). One circuit: Off - On. Bracket mounting holes 5/6" x 9/" (7.9 x 5.) on /64" centers (56.0mm). Intermittent Duty SPST normally Off, 750A make, 00A break 750A make, 00A break. 0 sec On, 0 min Off. Bracket mounting holes 5/6 x, /64" on centers (7.9 x 5., 56.mm). Contact terminals 5/6" -4 thread. 4076, Insulated Without PVC coating: see V 45 Continuous Duty: A. Without PVC coating: see V UL Listed Continuous Duty: 65A at 4V DC LISTED Intermittent Duty: 0A make, 65A break. 0 sec On, 0 min Off. Without PVC coating and UL rating: see 406 V MARINE 47 Continuous Duty: A. Without PVC coating: see , Insulated Without PVC coating: see , Grounded Without PVC coating: see UL Listed BP Continuous Duty: 65A at V DC Intermittent Duty: 750A make, 00A break. 0 sec On, 0 min Off. Without PVC coating: see MARINE LISTED V SPDT Normally Closed contacts 5A, Normally Open contacts A. Without PVC coating: see 440 Solenoid Info See page 8, and visit our website for an interactive training session on Solenoids Cole Hersee Co. 0 Old Colony Ave, Boston, MA T F

H PLASTIC BODY SOLENOIDS Glass-filled nylon construction - lightweight, durable and resistant to corrosion.

including lawn tractors, golf carts and sweepers. SPST normally open contacts. 00A make and break, 400A inrush. Silver contacts. Large studs: 5/6"-4.

Bracket mounting holes 5/6" x 9/" (7.9 x 5.) on /64" centers (56.0mm). 4V 464-0 Insulated F bracket, two 0- stud coil terminals.

46-0 Insulated F bracket, two 0- stud coil terminals. Grounded Intermittent Duty, 00A For starting small engines, including lawn tractors, golf carts and sweepers.

500A inrush, maximum On time 0 secs.) Allow at least 40 secs cooling after maximum On time. Copper contacts. Maximum operating voltage 4V DC.

Bracket mounting holes 5/6" x 9/" (7.9 x 5.) on /64" centers (56.0mm). 46-0 Insulated, V BP L bracket, 5/6" -4 large studs, two 0- stud coil terminals.

7 H PLASTIC BODY SOLENOIDS Glass-filled nylon construction - lightweight, durable and resistant to corrosion. H F bracket, insulated (two terminals) F bracket, grounded (one terminal) L bracket, insulated (two terminals) Continuous Duty, 00A For starting small engines, including lawn tractors, golf carts and sweepers. SPST normally open contacts. 00A make and break, 400A inrush. Silver contacts. Large studs: 5/6"-4. V type: maximum operating voltage 4V DC. 4V type: maximum operating voltage 7V DC. 6V type: maximum operating voltage 6V DC. Cycle life: 50,000 minimum. Bracket mounting holes 5/6" x 9/" (7.9 x 5.) on /64" centers (56.0mm). 4V Insulated F bracket, two 0- stud coil terminals. V 45-0 Insulated F bracket, two blade coil terminals. Insulated 46 Insulated L bracket, two 0- stud coil terminals Insulated F bracket, two 0- stud coil terminals. Grounded Intermittent Duty, 00A For starting small engines, including lawn tractors, golf carts and sweepers. V DC. SPST normally open contacts. 00A make and break, 5 secs On, 5 secs Off, 00A inrush. (Sealed solenoids 00A make and break, 5 secs On, 5 secs Off. 500A inrush, maximum On time 0 secs.) Allow at least 40 secs cooling after maximum On time. Copper contacts. Maximum operating voltage 4V DC. Cycle life: 0,000 minimum. Sealed solenoids are protected against ingress of contaminants such as oil or gasoline, dirt and moisture. Bracket mounting holes 5/6" x 9/" (7.9 x 5.) on /64" centers (56.0mm) Insulated, V BP L bracket, 5/6" -4 large studs, two 0- stud coil terminals. 46- Insulated, V F bracket, 5/6" -4 large studs, two 0- stud coil terminals. 47-GS7 Grounded, V, Sealed F bracket, /4" -0 large studs, one 8- stud coil terminals. New Ignition Switches 46-G0 Grounded F bracket, one 0- stud coil terminals. New Series is fully sealed and has an integral Deutsch connector. See page 9. Cole Hersee Co. 0 Old Colony Ave, Boston, MA T F

H H PLASTIC BODY SOLENOIDS Heavy Service, 5A For use with heavy vehicles, materials handling, hydraulic systems, large DC machinery, and electric vehicles.

V silver contact, 50k cycles. Copper contact. Maximum operating voltage 4V DC, cycle life 5,000 minimum. Bracket mounting holes 5/6" x 9/" (7.9 x 5.

Common ground coil. Two blade coil terminals, 5/6" -4 large studs. Copper contacts. F bracket. 75A make and break, maximum On time 5 mins.

5V DC. Cycle life 0,000 cycles at 5 secs On, 5 secs Off. Shipped with mounting hardware.

switch (such as 75705-0). Also available as 4V: 4450-0 with same rating as 4450. Contact Cole Hersee. 484-0V Silver contacts. 48 V Copper contacts.

Forward MOTOR Reverse Super-Bright LEDs Reversing Solenoid New 58 series rocker switches have long lasting LED lights and high-visibility wrap-around lenses.

8 H H PLASTIC BODY SOLENOIDS Heavy Service, 5A For use with heavy vehicles, materials handling, hydraulic systems, large DC machinery, and electric vehicles. SPST normally open contacts. Insulated. -48V DC. Continuous duty, 5A make and break, 600A inrush. L bracket. Large studs: 5/6"-4, two 0- stud coil terminals. V silver contact, 50k cycles. Copper contact. Maximum operating voltage 4V DC, cycle life 5,000 minimum. Bracket mounting holes 5/6" x 9/" (7.9 x 5.) on /64" centers (56.0mm). Other types available by special order Motor Reversing Solenoid BP L bracket DPDT intermittent duty. V DC. Common ground coil. Two blade coil terminals, 5/6" -4 large studs. Copper contacts. F bracket. 75A make and break, maximum On time 5 mins. 5A make and break, maximum On time 0 secs. 50A make and break, maximum On time 0.5 secs. Allow 5 mins Off after max On time. Maximum operating voltage 4.5V DC. Cycle life 0,000 cycles at 5 secs On, 5 secs Off. Shipped with mounting hardware. Use in conjunction with one of many types of Cole Hersee SPDT momentary switches: rocker (such as ), rotary (such as 754-0/0) or ignition-type keyed switch (such as ). Also available as 4V: with same rating as Contact Cole Hersee V Silver contacts. 48 V Copper contacts. T BAT T 48-0 V Silver contacts. BAT V Copper contacts. Forward MOTOR Reverse Super-Bright LEDs Reversing Solenoid New 58 series rocker switches have long lasting LED lights and high-visibility wrap-around lenses. See page 9. For reversing motors such as hoists, winches, windlasses, ATVs and snowplow blades. Two solenoids in one for cost and space savings and simpler wiring. Two integral solenoids provide dynamic braking for permanent magnet motors when neither coil is energized. Cole Hersee Co. 0 Old Colony Ave, Boston, MA T F

H4 MODULES H 4 Electronic Solenoid A, 9V-V DC. Fully solid-state, with no moving parts to wear out. The Electronic Solenoid stands up to over 0 million On-Off cycles.

Use the Electronic Solenoid in both V or 4V applications... or any voltage between 9 and V. Solenoid can be used in both High Side and Low Side switching applications.

445 Forward & Reverse Relay Module Reversing module carries a heavy load and is suitable for intermittent or continuous operation at V DC.

9 H4 MODULES H 4 Electronic Solenoid A, 9V-V DC. Fully solid-state, with no moving parts to wear out. The Electronic Solenoid stands up to over 0 million On-Off cycles. It is completely sealed, ignition protected, and withstands vibration and adverse environments. Perfect for vehicles that are always on the move. Use the Electronic Solenoid in both V or 4V applications... or any voltage between 9 and V. Solenoid can be used in both High Side and Low Side switching applications. Needs only a very low control current. Suitable for high inrush demand circuits. 445 Forward & Reverse Relay Module Reversing module carries a heavy load and is suitable for intermittent or continuous operation at V DC. Ideal for tarp or lift applications as well as for hoists, hatches, winches/windlasses, snowplows, intake/exhaust fans, vehicle outriggers and many other direction reversing applications. Fully sealed to accommodate harsh environments. Dynamic braking stops the motor when the control switch is turned to Off. Low profile module (less than " high) saves space in cramped installations. Studs are securely secured in epoxy. Protective cover 9797 is also available. NEW Specifications: 9 - V DC, A continuous or 75A intermittent. Low On resistance of.005ω Low control current of.0a (max) means lighter wires, smaller harnesses. On/Off control voltage must be identical to the system voltage. Wide temperature operating range -40 C to C without derating. Protected from transient voltage spikes or surges. BAT Red Black LOAD BAT Red Black LOAD Specifications: High performance silver tin oxide contacts assure long cycle life. 70A at V DC intermittent, max On time 5 mins, Off time mins. 50A at V DC Continuous. For intermittent operation. Control switch should be Mom On Off Mom On; for continuous operation On Off On. Load current inrush: 50A. Pull-in voltage 7.8V max. Low coil current draw. Coil resistance 8 Ohms ± 0%. Vibration resistance: 0-55Hz. Double amplitude.55mm. Environmental: -40 C to C. Rust and moisture-resistant plastic housing. Fully sealed to IP67 with high strength epoxy for total moisture protection. Ignition protected. Tin-plated brass studs and hardware for corrosion resistance. Dielectric strength: 500V RMS between coil and contact. High side switching application Low side switching application Emergency Cutoff 00A Dual Relay Can be wired as a Latching Relay or as a Normally Open Relay. See page 99. Emergency cutoff switches are commonly mounted on many types of vehicles such as buses, and those used in construction and agriculture. Fire departments routinely familiarize themselves with the location of cutoffs, so that vehicles can quickly be isolated in case of emergency. Additionally, OSHA requires cutoffs on certain vehicles, particularly those with ancillary motorized equipment, such as garbage trucks. See Section J. Cole Hersee Co. 0 Old Colony Ave, Boston, MA T F

H H5 RELAYS Heavy Duty & High Power Relays General purpose relays fit many vehicles. Typical applications include: lighting, starting, horn, heating and cooling.

) Specifications: Ignition protected to SAE J7 Pull-in voltage: 7.8V maximum at V DC, 5.6V at 4V DC. Release voltage:.v minimum at V DC,.4V at 4V DC. Temperature range: -40 C to C.

10 H H5 RELAYS Heavy Duty & High Power Relays General purpose relays fit many vehicles. Typical applications include: lighting, starting, horn, heating and cooling. Standard ISO terminal footprint for Form A (SPST), Form C changeover (SPDT) and Form A (SPST, terminals). Relays are available sealed and unsealed (unsealed are supplied with snap-in brackets.) Specifications: Ignition protected to SAE J7 Pull-in voltage: 7.8V maximum at V DC, 5.6V at 4V DC. Release voltage:.v minimum at V DC,.4V at 4V DC. Temperature range: -40 C to C. Operational life: Electrical to 00,000 cycles; Mechanical to 0 million cycles. Contact Material: Silver alloy. Dielectric strength: 500V rms between coil and contact. Insulation resistance: 00M Ω minimum (500V DC). Vibration resistance: 0-40Hz double amplitude.5mm. Ignition protected to SAE J7, Section 5. Cole Hersee Relays are rated based on a steady state resistive load. De-rate according to the type of load: Motor load: Inrush can be 5 to 0 x steady state current. Solenoid load: Inrush can be 0 to 0 x steady state current. Incandescent lamp load: Inrush can be 0 to 5 x steady state current. Relays are also available with PC terminals. Contact Cole Hersee. Relay Schematics & Terminal Layouts Other configurations are available by special order. Form A (SPST) 0 Form A (SPST) with suppression 0 (-) () RESISTOR OR DIODE Form C (SPDT) 0 a 0.66 [6.8] [7.9] 0.66 [6.8] [7.9] 0.66 [6.8] 0.5 [8.00] 0 FORM A TERMINALS 0 FORM A TERMINALS 0 a FORM C TERMINALS 0. [8.40] 40A Type has.50" terminals. 70A Type has.75" terminals. 0. [8.40] 0. [8.40] [7.9] Heavy Duty Relays 40A at V DC Specifications: Contact rating (Resistive load) at 0 C: V DC: Normally Open 40A, Normally Closed 0A. 4V DC: Normally Open 0A, Normally Closed 5A. Contact arrangement: Available as Form A (SPST), Form C (SPDT) and Form A (SPST, terminals). Form C (SPDT) with suppression 0 a (-) () RESISTOR OR DIODE 0.66 [6.8] 0.5 [8.00] Form (SPST) with suppression 4 0 a FORM C TERMINALS 0. [8.40] [7.9] High Power Relays 70A at V DC Specifications: Contact rating (Resistive load) at 0 C: V DC: Normally Open 70A, Normally Closed 60A. 4V DC: Normally Open 5A, Normally Closed 0A. Contact arrangement: Available as Form A (SPST) and Form C (SPDT) [6.8] 0.5 [8.00] 0 FORM TERMINALS 5 0. [8.40] 0 (-) ().04 [6.5] Sq. Ref. RESISTOR OR DIODE Cole Hersee Co. 0 Old Colony Ave, Boston, MA T F

diode N: no seal RA-400-DN A: SPST 0 0 Snap-in 4 N: none N: no seal RA-004-NN A: SPST 0 0 Snap-in 4 R: resistor N: no seal RA-004-RN A: SPST 0 0 Snap-in 4 D: diode N: no seal RA-004-DN A: SPST 40 00

11 H5 RELAYS H Relay Stock Items Other configurations, and PC terminals are available. Contact Cole Hersee. FORM AMPERAGE BRACKET VOLTAGE SUPPRESSOR SEAL PART NUMBER **DIAGRAM A: SPST 40 0 Snap-in N: none N: no seal RA-400-NN A: SPST 40 0 Snap-in R: resistor N: no seal RA-400-RN A: SPST 40 0 Snap-in D: diode N: no seal RA-400-DN A: SPST 0 0 Snap-in 4 N: none N: no seal RA-004-NN A: SPST 0 0 Snap-in 4 R: resistor N: no seal RA-004-RN A: SPST 0 0 Snap-in 4 D: diode N: no seal RA-004-DN A: SPST None D: diode S: sealed RA-4000-DS A: SPST 0 00 None 4 D: diode S: sealed RA-0004-DS C: SPDT 40 0 Snap-in N: none N: no seal RC-400-NN C: SPDT 40 0 Snap-in R: resistor N: no seal RC-400-RN 4 C: SPDT 40 0 Snap-in D: diode N: no seal RC-400-DN 4 C: SPDT 0 0 Snap-in 4 N: none N: no seal RC-004-NN C: SPDT 0 0 Snap-in 4 R: resistor N: no seal RC-004-RN 4 C: SPDT 0 0 Snap-in 4 D: diode N: no seal RC-004-DN 4 C: SPDT None D: diode S: sealed RC-4000-DS 4 C: SPDT 0 00 None 4 D: diode S: sealed RC-0004-DS 4 : SPST 0 0 Snap-in 4 R: resistor N: no seal R-004-RN 5 : SPST 40 0 Snap-in R: resistor N: no seal R-400-RN 5 A: SPST 70 0 Snap-in N: none N: no seal RA-700-NN A: SPST 70 0 Snap-in R: resistor N: no seal RA-700-RN A: SPST 70 0 Snap-in D: diode N: no seal RA-700-DN C: SPDT 70 0 Snap-in N: none N: no seal RC-700-NN C: SPDT 70 0 Snap-in R: resistor N: no seal RC-700-RN 4 C: SPDT 70 0 Snap-in D: diode N: no seal RC-700-DN 4 Relay & MicroRelay Part Number Structure R A 40 0 R S A C Form A (SPST) Form C (SPDT) Form A (SPST, terminals) R Relay M MicroRelay V DC 4 4V DC 00 Without bracket* 0 With snap-in bracket 5 5V at 4V DC 0 0A at 4V DC 5 5A at 4V DC 5 5A at 4V DC 40 40A at V DC 70 70A at V DC S Sealed* N Nothing (no sealing) R Resistor D Diode N Nothing (no suppressor) * No bracket is supplied with the sealed relays. Relays without seals are supplied with a snap-in bracket, and can be used with or without the bracket. Relay Sockets Accepts Cole Hersee relays and standard ISO relays. Modular sockets dovetail together. Accepts standard quick-connect terminals. Easy mount bracket. Constructed of rugged glass-filled polyamide. Temperature range -40F to C High Power Socket 9906 Heavy Duty Socket For use with Cole Hersee Heavy Duty Relays. Form A (SPST) or Form C (SPDT). Use with Tyco (AMP) terminals 48 or Ark-Les 000HA series (consult terminal manufacturers for full specs). For use with Cole Hersee High Power Relays. Form A (SPST) Use with Tyco (AMP) terminals or (consult terminal manufacturers for full specs). Cole Hersee Co. 0 Old Colony Ave, Boston, MA T F

12 H H5 RELAYS MicroRelays 5A at V DC MicroRelays fit many vehicles and applications. They have a reduced size, but can accept a 5A load. Typical applications include: lamp control, horns, power windows, fuel pumps, fans and lifts gates. Standard terminal footprint for Form A (SPST), Form C changeover (SPDT) MicroRelays are available sealed and unsealed. MicroRelay Schematics & Terminal Layouts Other configurations are available by special order. Form A (SPST) Form A (SPST) with suppression Specifications: Contact rating (Resistive load) at 0 C: V DC: Normally Open 5A, Normally Closed 0A. 4V DC: Normally Open 5A, Normally Closed 0A. Contact arrangement: Available as Form A (SPST), and Form C (SPDT). Ignition protected to SAE J7. Vibration resistance: 0-40Hz double amplitude.7mm. Pull-in voltage: 7.8V maximum at V DC, 5.6V at 4V DC. Release voltage:.v minimum at V DC,.4V at 4V DC. Temperature range: -40 C to C. Operational life: Electrical to 00,000 cycles. Mechanical to 0 million cycles. Contact Material: Silver alloy. Dielectric strength: 500V rms between coil and contact. Insulation resistance: 00MΩ minimum (500V DC). Cole Hersee Relays are rated based on a steady state resistive load. De-rate according to the type of load: 0 (-) () RESISTOR OR DIODE 7 Form C (SPDT) 0 a Motor load: Inrush can be 5 to 0 x steady state current. Solenoid load: Inrush can be 0 to 0 x steady state current. Incandescent lamp load: Inrush can be 0 to 5 x steady state current. MicroRelays are also available with PCB terminals: contact Cole Hersee. Form C (SPDT) with suppression a (-) () RESISTOR OR DIODE MicroRelay Stock Items Other configurations, and PC terminals are available. Contact Cole Hersee. FORM AMPERAGE VOLTAGE SUPPRESSOR SEAL PART NUMBER **DIAGRAM A: SPST 5 R: resistor N: no seal MA-500-RN 7 A: SPST 5 R: resistor S: sealed MA-500-RS 7 A: SPST 5 D: diode N: no seal MA-500-DN 7 A: SPST 5 N: none N: no seal MA-500-NN 7 A: SPST 5 4 N: none N: no seal MA-5004-NN 6 C: SPDT 5 R: resistor N: no seal MC-500-RN 9 C: SPDT 5 R: resistor S: sealed MC-500-RS 9 C: SPDT 5 D: diode N: no seal MC-500-DN 9 C: SPDT 5 N: none N: no seal MC-500-NN 8 C: SPDT 5 4 R: resistor N: no seal MC-5004-RN 9 C: SPDT 5 4 N: none N: no seal MC-5004-NN 8 Cole Hersee Co. 0 Old Colony Ave, Boston, MA T F

13 H6 INFORMATION ON SOLENOIDS H How Solenoids Work Solenoids are relays which are commonly used to remotely switch a heavier current. By using a solenoid, the amount of heavy wiring needed to power the load is reduced, since the control circuit mounted inside the cab typically utilizes a smaller wire gauge. Solenoids are commonly used to control starter and winch motors, and they have many other uses on vehicles of all kinds. Latching Solenoid Applications A Remote Battery Isolator In a two-battery system, use the Latching Solenoid to isolate the batteries from each other, and prevent battery drain from the higher into the lower. It has an advantage over electronic Battery Isolators (see Battery-Related Products), in that it will not produce a voltage drop during operation. ALTERNATOR BATTERY TERMINAL CONTROL CIRCUT STUDS COIL HOUSING B PLUNGER CONTROL CIRCUIT STUDS LOAD CIRCUT STUDS 4-stud solenoid diagram L MAIN LOAD 4 B L SECONDARY LOADS A Remote Battery Disconnect LOAD CIRCUIT STUDS A typical 4-stud solenoid The diagram shows a magnetic coil surrounding a contact plunger. Before energization, the plunger is not electrically connected to the control circuit. When the control circuit is energized, the electromagnetic force induced in the coil attracts the plunger, which moves to close the load circuit. When the control circuit is de-energized, the spring-loaded plunger returns to its normal state and the load circuit is broken. In continuous duty applications, energization of the coil causes heating, therefore the solenoid housing will become warm even in normal operation. Use it as a remote Battery Disconnect Switch. This eliminates the need for heavy gauge wiring between the control panel and the battery. B 4 L Pilot Light B B L Solenoid in its normal state Control circut and load circuit open B Energized solenoid Control circut and load circuit closed L B For more information on solenoids, visit the interactive training section of the Cole Hersee website: > Resource Center > Training Cole Hersee Co. 0 Old Colony Ave, Boston, MA T F

H notes For orders or questions please call (67) 68-00 or visit us on the web at www.colehersee.

14 H notes For orders or questions please call (67) or visit us on the web at Largest amp capacity for the dollar of any competitive switch 500A intermittent, 0A continuous, 6-6V DC Large knob for easy grip... even when wearing gloves. Flange for easy flush mounting. Can also mount through a panel. Heavy spring ensures rock-solid electrical contact and provides strong detent action to the switch. /8" - 4 copper studs are solidly machined to the contact plates and cannot come apart. All-weather hardware: heavy copper studs and brass nuts for maximum current capacity. Max Starting Power Delivers maximum starting power: allows either or both batteries to be used. Can be switched between batteries even when the engine is running. Impact-Resistant Rugged polyester thermoplastic case and knob. Stands up to impact, maintains its water-resistant integrity. Water-Resistant High-performance synthetic rubber o-ring keeps out water, contaminants and vapors. Many battery switches have no o-ring! 500 Amp Capacity Solid copper contact plates. Easily handles amperages as high as 500A intermittent. Largest amp capacity for the dollar of any battery switch. Corrosion-Proof Stainless steel screws securely hold the plate against the o-ring, and keep the switch watertight. Cole Hersee Co. 0 Old Colony Ave, Boston, MA T F

solenoids & relays solenoids & relays Continuous Duty 24V insulated 48V insulated 36V insulated A UL-listed

solenoids & relays solenoids & relays Continuous Duty 24V insulated 48V insulated 36V insulated A UL-listed PVC COATED SOLENOIDS WITH STEEL HOUSINGS PLASTIC ODY SOLENOIDS ELECTRONIC SOLENOIDS RELAYS H H H H4 H5 H H INFORMATION ON SOLENOIDS H6 Continuous Duty 85A except where noted. Normally Open Contacts, SPST,