mb808 FAB manual
|
|
- Roy Sutton
- 6 years ago
- Views:
Transcription
1 mb808 FAB manual
2 Step one: Power Supply: ATTENTION: You will be dealing with AC mains voltages in this part of the build, if you are not careful you can injure yourself, or worse! Keep a clean bench and *PAY ATTENTION* to what you are doing! 1.) Solder in all diodes except D41. 2.) Solder in the two 1K resistors and LED's 1 and 2. 2.) Solder in all 100n capacitors except c24. Any poly or lytic cap will work here and a voltage rating of at least 35v is reccomended. Place c24 on the top side of the board so it doesn't get in the way of the heatsink on the 5v regulator. Leave enough leads on the cap so that it will lie flat on the PCB and not get in the way of the front panel. 3.) Solder in the 4 pin connector for the transformer in with the friction lock on the north side of the board (this is in backwards on mine). 4.) Solder in the fuses. The PSU will still function without them, but do so at your own risk. 5.) Attach heatsinks to the regulators. You *must* use a heatsink on the 5v regulator, but you may be able to get away without them on the +15v regulators. In either case be aware that these IC's can and will get *very* hot! 6.) Solder in the Regulators with the metal tab to the north side of the board. 7.) Solder in the big lytic caps. These should all be at least 35 volts except c22 which can be as low as 6.3v because it is after the 5V regulator. It's not a bad idea to use a 2200uF 16v cap for c22.
3 8.) Double check that all components except D41 are soldered in. Check for solder bridges by using the continuity tester on your DMM. 9.) Connect the wires of the transformer's primary winding to the power jack and power switch. If you are using the Amveco transformer the wires should be connected Red and Yellow together to one pole of the switch and Black and Purple together to one tab on the power jack. Connect the other tab on the power jack to the other pole of the switch. In the Pic you can see that I soldered the power switch directly to the inlet jack. Obviously this won't work in a case, but while testing it kept the amount of wiring that was carrying AC mains to a minimum.
4 10.) Connect the wires from the secondary windings on the transformer to the connector in the order Blue, Brown, Red, Green. 11.) Place a 125v fuse in the power jack. 12.) Connect a power cable and test for AC voltage from Blue to Brown and Green to Red 13.) Connect the power connector to the PCB, power it on, and check for voltage across the two large capacitors. If there is at least 15v then check for +15v at the outputs of the regulators (the LED's should be on and stay on). 14.) Solder in D41. BE ABSOLUTELY SURE THAT THE CAPS ARE DISCHARGED. Place a 10K resistor across their terminals for 10 seconds first if you are not sure. 15.) Check the output of the 5V regulator.
5 Bill Of Materials Partlist exported from 808_production_PSU.sch at 5/10/ :22:07p Qty Value Device Parts Notes 1-15 volt regulator IC36 2 PCB mounted F1, F3 fuse 2 3MM LED LED1, LED2 1 3 Pin Header DC-OUT 1 4 Pin.156" spaced SV1 header 9 1N4004 Power Diode D29, D32, D33, D34, D35, D36, D37, D38, D Electrolytic Capacitor C211, C212, C213, C214, C215, C216, C222, C223, C224, C225, C226, C227, C228, C229, C230, C231, C232, C233, C234, C235, C236, C V 15 volt regulator IC2 1 78V 15 volt regulator IC n Electrolytic C9, C23, C24, C25, C26, C112 Capacitor 2 470K Resistor R382, R uf Electrolytic C21, C22 Capacitor uf Electrolytic C8, C10 Capacitor 1 MA pin header
6 Step Two: The Core For additional information about the MidiBox Core module, see these pages: ) Solder in all resistors 2.) Solder in the 2 100n (104) capacitors 3.) Solder int he Crystal, it does not matter which direction 4.) Solder in the Diodes 5.) Solder in the 40 pin socket for the PIC and the 2 8 pin sockets for the Opto Isolator and the EEPROM 6.) Solder in the optional components R6, R7 and T1 which are used to adjust the brightness and contrast of the LCD screen. Transistor T1 is a BC337 so if you want to use a 2n3904 you will need to bend the leads as the pinout is different (I'll check the datasheet and make a diagram). 7.) Solder in the 2 33p capacitors next to the crystal 8.) Before putting any IC's in their sockets power the unit on and test for 5v across the 100n capacitors.
7 9.) Connect a MIDI cable to the output connector 10.) Using a program like MIDIOx or (preferably) MIOS Studio ( watch the input midi monitor when you power the unit on (remember to put the IC's in now). You should see a HEX message similar to F etc. If you see nothing start checking components around the MIDI out port. 11.) Alternately you can connect a LCD to the Core and see if the application boots up. If you can't see anything at first remember to adjust the brightness and contrast pots. I'll post some more detailed information about connecting the LCD's once I find it, but remember that this is all standard MidiBox stuff, so search the midibox forum and wiki! Be careful with a LCD hooked up.. in all likelyhood the 5v regulator is going to get *very* hot!
8 Bill Of Materials Partlist exported from 808_production_Core.sch at 5/10/ :17:45p Qty Value Device Parts Mouser 2 3 Pin Header MIDI-IN, MIDI-OUT Pin Header SV Dual 4 Pin header SV2 1 Dual 8 Pin Header SV4 1 Resistor R K Resistor R10, R11, R18 1 1K2 Resistor R N4148 Diode D1 1 10MHZ Timer Crystal XTAL 1 5K6 Resistor R N138 OptoCoupler OPTO-ISO 2 10K Trim Pot R6, R7 2 10K Resistor R8, R KB Pot SWING 1 24LC256P EEPROM IC1 2 33p Ceramic Disc Capacitor C19, C n Mulitilayer Ceramic Capacitor C17, C R R-US_0207/7 R138, R140, R141 1 BC337 Transistor T1 1 PIC18F4X2DIL40 Microcontroller MCU
9 Step Three: DOUTs For more information about these circuits check out these sites: The top two rows of IC's in the digital section are the Digital Outs which are responsible for controlling the LED's and sending the Instrument and Accent trigger pulses. TIP: It is not a bad idea to test for continuity between the 5v rail and ground after soldering in each Socket, it's much easier to identify solder bridges this way. 1.) Solder in the 16 pin sockets (Note, some early versions of the BOM have the count for 14 and 16 pin sockets mixed up, you will need pin sockets total) 2.) Solder in the 100n (104) capacitors, one per set of sockets. Bill Of Materials Partlist exported from 808_production_Dout.sch at 5/10/ :20:00p Qty Value Device Parts 2 Lighted Tact Switch LED42, LED K Resistor Network RN2, RN3, RN5, RN6, RN n Multilayer Ceramic cap C1, C2, C3, C4, C5, C6, C7 7 74HC595N 74HC595N IC9, IC10, IC11, IC12, IC13, IC14, IC R Resistor Network RN1, RN4 2 s14 LED3MM BAR-LED, BEAT-LED
10 Step Four: DIN's For more information about these circuits, please check out these sites: TIP: It's not a bad idea to check for continuity between the 5v rail and ground after soldering in each IC socket. 1.) Solder in the 16 pin IC sockets. 2.) Solder in the 100n caps 3.) Solder in the in line resistor networks. They should have a marking on one end indicating the common pin. This pin should be connected to the 5v rail on the pcb (the thick trace) this pin is on opposite sides for each side of the IC. You can ignore the resistor that is silkscreend on the PCB. If your networks have an extra pin (or more) just bend the unused ones up out of the way. 4.) Don't solder in the switches, they will be the last components to go in the board. Bill Of Materials Partlist exported from 808_production_Din.sch at 5/10/ :19:43p Qty Value Device Parts 33 Lighted Tact Switch A, B, EDIT, EXIT, FWD, GP-1, GP-2, GP-3, GP-4, GP-5, GP-6, GP-7, GP-8, GP-9, GP-10, GP-11, GP-12, GP-13, GP-14, GP15, GP16, LOOP, MENU1, MENU2, MENU3, MENU4, MUTE, PATTERN, PLAY, RWD, SELECT, SONG, STOP 12 10K Resistor Network RN13, RN14, RN15, RN16, RN17, RN18, RN19, RN20, RN21, RN22, RN23, RN K Resistor R1, R2, R3, R4, R5, R n Electrolytic C11, C12, C13, C14, C15, C16 Cap 6 74HC165N 74HC165N IC3, IC4, IC5, IC6, IC7, IC8 2 SNAPIN- ENCODER Rotary Encoder INSTRUMENT, TEMPO
11 Step Five: Trigger Indicators TIP: Don't solder these components in right away if you think you might want to use the dual LCD's TIP: DON'T SOLDER IN THE Capacitors or any components marked with a red dot on the diagram! 1.) Solder in the 100k and 1k resistors. Pay attention to their position, only most of them follow the same pattern. 2.) Solder in *ONE* transistor for each indicator. The second one (along with the cap) is there to make the LED blink brighter.. but it's not a very good circuit, so it's best you simply ignore it. Check back here for a pic showing which transistors not to solder in. 3.) Using LED spacers *carefully* solder in each LED so that it is completely straight and true to the PCB Bill Of Materials Partlist exported from 808_production_TriggerLED.sch at 5/10/ :22:51p Qty Value Device Parts 12 3mm LED BD-SEL, CB-SEL, CH-SEL, CP-SEL, CY-SEL, HT-SEL, LT-SEL, MA-SEL, MT-SEL, OH-SEL, RS-SEL, SD-SEL 12 1K Resistor R442, R445, R448, R451, R454, R457, R460, R466, R469, R472, R475, R N3904 Transistor T3, T4, T5, T6, T7, T8, T9, T11, T12, T13, T14, T K Resistor R440, R441, R443, R444, R446, R447, R449, R450, R452, R453, R455, R456, R458, R459, R464, R465, R467, R468, R470, R471, R473, R474, R476, R477
12 Step Six: BD With the BD (and all the other instrument circuits) all you need to do is solder in the components, go by order of their height to make the physical assembly easier. DON'T solder in the pots, trim pots or switches, those will be the last things you solder in. Once you've finished each circuit check for continuity from the 15v rails and ground to be sure there isn't a bridge there. Note that the BOM lists the Op-Amp as a TL072. It will work just fine in this circuit, but the original uses JRC4558's
13 Bill Of Materials Partlist exported from 808_production_BD.sch at 5/10/ :17:11p Qty Value Device Parts 1 SPDT Switch BD-RT 2.47/50 Electrolytic Capacitor C27, C47 1 1uF 50 Volt Electrolytic Capacitor C50 1 1K Resistor R M Resistor R156, R161, R N4148 Diode D52, D53 1 2K7 Resistor R SA733 PNP Transistor Q40 5 2SC945 NPN Transistor Q39, Q41, Q42, Q43, Q44 1 4K7 Resistor R K7 Resistor R K Resistor R K8 Resistor R K2 Resistor R K Resistor R153, R154, R KA Pot BD-TUNE 1 10KB Pot BD-TONE 3 15n Polyester Capacitor C40, C41, C K Resistor R K Resistor R152, R165, R /6.3 Electrolytic Capacitor C n Polyester Capacitor C K Resistor R K Resistor R K Resistor R K Resistor R159, R163, R174, R KA Pot BD-LEV 2 100n Polyester Capacitor C38, C R Resistor R p Ceramic Capacitor C K Resistor R KB Dual Pot BD-DECAY 2 MA Pin Header U$21, U$55 1 TL072P OpAmp IC17
14 Step Seven: SD
15 Bill Of Materials Partlist exported from 808_production_SD.sch at 5/10/ :22:38p Qty Value Device Parts 1 SPDT Switch SD-RT 1.47/50 Electrolytic Capacitor C n Polyester Capacitor C51, C52 21K Resistor R19, R28 11M Resistor R22 11N4148 Diode D2 11n Polyester Capacitor C n Polyester Capacitor C53 12K2 Resistor R40 12M2 Resistor R38 12SA733 PNP Transistor U$2 42SC945 NPN Transistor U$1, U$4, U$5, U$6 14K7 Resistor R n Polyester Capacitor C28, C32, C33 18K2 Resistor R20 210K Resistor R9, R14 110KB Pot SD-SNAPPY 110n Polyester Capacitor C54 215K Resistor R30, R33 322K Resistor R12, R34, R36 122n Polyester Capacitor C55 127K Resistor R39 227n Polyester Capacitor C29, C30 133/6.3 Electrolytic Capacitor C36 133K Resistor R29 147/16 Electrolytic Capacitor C44 347K Resistor R23, R25, R35 247n Polyester Capacitor C31, C K Resistor R15, R KB Pot SD-LEV, SD-TONE 2100R Resistor R32, R n Polyester Capacitor C R Resistor R p Ceramic Capacitor C R Resistor R K Resistor R R Resistor R17, R K Resistor R16 2 MA Pin Header U$57, U$71 2 TL072P OpAmp IC18, IC19
16 Step Eight: Noise Bill Of Materials Partlist exported from 808_production_Noise.sch at 5/10/ :21:50p Qty Value Device Parts 1 1uF 50volts Electrolytic Capacitor C M Resistor R278, R SC828 Transistor U$30 1 4K7 Resistor R n Polyester Capacitor C KB Trim Pot CB-TUNE3 2 22K Resistor R279, R n Polyester Capacitor C /16 Electrolytic Capacitor C R Resistor R K Resistor R K Resistor R283 1 TL072P OpAmp IC31
17 Step Nine: LT
18 Bill Of Materials Partlist exported from 808_production_LT.sch at 5/10/ :20:59p Qty Value Device Parts 1 SPDT Switch LT-RT 1 DPDT Switch LT/LC 2 1K Resistor R52, R57 1 1K5 Resistor R65 1 1MB Dual Pot LT-DECAY 2 1N60 Germanium Diode U$3, U$19 2 1N4148 Diode D4, D7 1 1n Polyester Capacitor C61 1 2M2 Resistor R63 1 2SA733 PNP Transistor Q5 2 2SC945 NPN Transistor Q6, Q7 1 3K3 Resistor R61 5 4K7 Resistor R41, R45, R46, R47, R n Polyester Capacitor C K Resistor R42, R n Polyester Capacitor C K Resistor R n Polyester Capacitor C K Resistor R43, R58, R /6.3 Electrolytic Capacitor C K Resistor R K Resistor R49, R n Polyester Capacitor C K Resistor R n Polyester Capacitor C59, C n Polyester Capacitor C64, C n Polyester Capacitor C K Resistor R53, R KA Pot LT-LEV, LT-RVB 1 470K Resistor R R Pot LT-TUNE 1 820K Resistor R K Resistor R388 2 MA Pin Header U$58, U$72 1 TL074P Quad OpAmp IC20
19 Step Ten: MT
20 Bill Of Materials Partlist exported from 808_production_MT.sch at 5/10/ :21:30p Qty Value Device Parts 1 SPDT Switch MT-RT 1 DPDT Switch MT/MC 21K Resistor R114, R119 11MB Dual Pot MT-DECAY 21N60 Germanium Diode U$22, U$23 21N4148 Diode D8, D9 11n Polyester Capacitor C n Polyester Capacitor C99 12K2 Resistor R210 12M2 Resistor R209 12SA733 PNP Transistor Q8 22SC945 NPN Transistor Q9, Q10 13K3 Resistor R207 44K7 Resistor R86, R90, R91, R188 16K8 Resistor R92 210K Resistor R87, R89 112n Polyester Capacitor C K Resistor R n Polyester Capacitor C K Resistor R88, R120, R213, R n Polyester Capacitor C100, C /6.3 Polyester Capacitor C K Resistor R99 233K Resistor R94, R n Polyester Capacitor C119, C n Polyester Capacitor C K Resistor R n Polyester Capacitor C K Resistor R115, R KA Pot MT-LEV, MT-RVB 1470K Resistor R R Pot MT-TUNE 1820K Resistor R K Resistor R387 2 MA pin header U$60, U$73 1 TL074P Quad OpAmp IC27
21 Step Eleven: HT
22 Bill Of Materials Partlist exported from 808_production_HT.sch at 5/10/ :20:30p Qty Value Device Parts 1 SPDT Switch HT-RT 1 DPDT Switch HT/HC 2 1K Resistor R225, R K5 Resistor R MB Dual Pot HT-DECAY 2 1N60 Germanium Diode U$24, U$25 2 1N4148 Diode D15, D18 1 1n Polyester Capacitor C n Polyester Capacitor C M2 Resistor R SA733 PNP Transistor Q11 2 2SC945 NPN Transistor Q12, Q13 1 3K3 Resistor R K7 Resistor R113, R218, R219, R n Polyester Capacitor C K6 Resistor R K Resistor R215, R n Polyester Capacitor C K Resistor R K Resistor R216, R231, R239, R n Polyester Capacitor C n Polyester Capacitor C124, C /6.3 Electrolytic Capacitor C K Resistor R K Resistor R222, R n Polyester Capacitor C127, C K Resistor R n Polyester Capacitor C K Resistor R226, R KA Pot HT-LEV, HT-RVB 1 470K Resistor R R Pot HT-TUNE 1 820K Resistor R K Resistor R345 2 MA Pin Header U$68, U$74 1 TL074P Quad OpAmp IC28
23 Step Twelve: CP
24 Bill Of Materials Partlist exported from 808_production_CP.sch at 5/10/ :17:59p Qty Value Device Parts 1 SPDT Switch CP-RT 1.47uF 50v Electrolytic Capacitor C n Polyester Capacitor C81 11uF 50v Electrolytic Capacitor C77 31K Resistor R158, R179, R201 41M Resistor R68, R69, R192, R198 41N4148 Diode D19, D20, D21, D22 21n Polyester Capacitor C87, C92 12K2 Resistor R181 12K7 Resistor R190 32SA733 PNP Transistor U$7, U$13, U$14 42SC945 NPN Transistor U$8, U$9, U$12, U$ n Polyester Capacitor C79, C80, C82 14K7 Resistor R197 34K7 Resistor R67, R195, R196 15K6 Resistor R K Resistor R66, R136, R145, R149, R187, R KB Trimpot CP-OFFSET 315K Resistor R147, R180, R n Polyester Capacitor C75, C83 222K Resistor R51, R n Polyester Capacitor C84 227K Resistor R150, R n Polyester Capacitor C88 133uF 6.3v Electrolytic Capacitor C90 133n Polyester Capacitor C78 139K Resistor R K Resistor R151, R199, R n Polyester Capacitor C76 268K Resistor R185, R K Resistor R K Resistor R148, R KA Pot CP-LEV 2220p Ceramic Capacitor C86, C K Resistor R R Resistor R144, R K Resistor R K Resistor R R Resistor R146 1 LM3080N OTA IC22 2 MA Pin Header U$61, U$75 1 TL072P OpAmp IC21 1 TLC339P Quad Comparator IC39
25 Step Thirteen: MA Bill Of Materials Partlist exported from 808_production_MA.sch at 5/10/ :21:14p Qty Value Device Parts 1 SPDT Switch MA-RT 11K Resistor R111 11M Resistor R107 31N4148 Diode D3, D5, D6 21n Polyester Capacitor C105, C106 32SA733 PNP Transistor U$11, U$16, U$20 32SC945 NPN Transistor U$10, U$17, U$18 13K3 Resistor R103 14K7 Resistor R96 16K8 Resistor R K Resistor R95, R98, R n Polyester Capacitor C104, C K Resistor R K Resistor R97, R /6.3 Electrolytic Capacitor C n Polyester Capacitor C K Resistor R n Polyester Capacitor C K Resistor R K Resistor R K Resistor R KA Pot MA-LEV 1100n Polyester Capacitor C K Resistor R K Resistor R p Ceramic Capacitor C K Resistor R K Resistor R101 2 MA Pin Header U$63, U$77 1 TL072P OpAmp IC26
26 Step Fourteen: RS
27 Bill Of Materials Partlist exported from 808_production_RS.sch at 5/10/ :22:24p Qty Value Device Parts 1 SPDT Switch RS/CL-RT 1 DPDT Switch RS/CL 1.47uF 50v Electrolytic Capacitor C73 11K Resistor R72 21K Resistor R125, R503 11M Resistor R81 11M Resistor R390 41N4148 Diode D11, D12, D13, D14 11n Polyester Capacitor C n Polyester Capacitor C70, C71, C72 12M2 Resistor R84 12SA733 PNP Transistor U$29 42SC945 NPN Transistor U$28, U$31, U$33, U$59 12SK30 FET Transistor U$ n Polyester Capacitor C67, C74, C95, C96 14K7 Resistor R K Resistor R80 110uF 16v Electrolytic Capacitor C97 110K Resistor R K Resistor R77, R83, R121, R124, R126, R129, R n Polyester Capacitor C68, C91 522K Resistor R85, R122, R128, R133, R n Polyester Capacitor C p Ceramic Capacitor C93 133/6.3 Electrolytic Capacitor C94 233K Polyester Capacitor R75, R K Resistor R73 347K Resistor R78, R132, R n Polyester Capacitor C K Resistor R KA Pot RS/CL-LEV 3220K Resistor R76, R82, R K Resistor R K Resistor R K Resistor R K Resistor R K Resistor R71 2 MA Pin header U$62, U$76 2 TL072P OpAmp IC24, IC25
28 Step Fifteen: CB
29 Bill Of Materials Partlist exported from 808_production_CB.sch at 5/10/ :17:27p Qty Value Device Parts 1 SPDT Switch MA-RT1 1.47/50 Electrolytic Capacitor C134 21uF 50v Electrolytic Capacitor C135, C142 31K Resistor R256, R260, R277 31N4148 Diode D10, D16, D n Polyester Capacitor C138, C139 32K2 Resistor R252, R257, R258 12SA733 PNP Transistor Q1 42SC945 NPN Transistor Q2, Q3, Q4, U$ n Polyester Capacitor C140 14K7 Resistor R224 15K6 Resistor R262 18K2 Resistor R uF 16v Electrolytic Capacitor C136, C K Resistor R243, R250, R251, R n Polyester Capacitor C n Polyester Capacitor C148, C n Polyester Capacitor C146, C147, C K Resistor R241, R242, R n Polyester Capacitor C143, C K Resistor R259, R264, R /6.3 Electrolytic Capacitor C K Resistor R244, R245, R KA Pot CB-LEV 2100R Resistor R246, R K Resistor R265, R268, R270, R272, R274, R K Resistor R K Resistor R KB Trim Pot CB-TUNE1, CB-TUNE2 3470K Resistor R247, R249, R K Resistor R273, R K Resistor R N Schmitt Trigger IC30 2 MA Pin Header U$64, U$78 1 TL072P OpAmp IC29
30 Step Sixteen: CY
31 Bill Of Materials Partlist exported from 808_production_CY.sch at 5/10/ :19:25p Qty Value Device Parts 1 SPDT Switch CY-RT 1.47/50 Electrolytic Capacitor C n Polyester Capacitor C159, C166, C170, C171, C185, C uF 50v Electrolytic Capacitor C167, C173, C K Resistor R MB Dual Pot CY-DECAY 6 1N4148 Diode D23, D24, D25, D26, D27, D28 5 1n Polyester Capacitor C155, C175, C176, C179, C /50 Electrolytic Capacitor C165, C K2 Resistor R M Resistor R290, R295, R SA733 PNP transistor U$37 7 2SC945 NPN Transistor U$32, U$34, U$35, U$36, U$38, U$39, U$ n Polyester Capacitor C156, C157, C161, C177, C K7 Resistor R K Resistor R n Polyester Capacitor C162, C K Resistor R299, R304, R311, R323, R n Polyester Capacitor C178, C181, C184, C K Resistor R K Resistor R314, R KB Pot CY-TONE 11 22K Resistor R286, R294, R300, R302, R303, R308, R315, R317, R318, R328, R n Polyester Capacitor C158, C164, C /6.3 Electrolytic Capacitor C K Resistor R289, R291, R296, R309, R310, R K Resistor R K Resistor R307, R320, R /16 Electrolytic Capacitor C K Resistor R K Resistor R287, R292, R K Resistor R KA Pot CY-LEV 5 100R Resistor R288, R293, R297, R298, R p Ceramic Capacitor C K Resistor R312, R R Resistor R333, R334 2 MA Pin Header U$65, U$79 3 TL072P OpAmp IC32, IC33, IC34
32 Step Seventeen: HH
33 Bill Of Materials Partlist exported from 808_production_HH.sch at 5/10/ :15:09p Qty Value Device Parts 2 SPDT Switch CH-RT, OH-RT 2.47/50 Electrolytic C190, C192 Capacitor 6 1.5n Polyester Capacitor C195, C196, C197, C198, C199, C K Resistor R374, R M Resistor R MB Dual Pot OH-DECAY 2 1N4148 Diode D30, D31 2 1n Polyester Capacitor C200, C K7 Resistor R365, R M Resistor R363, R SA733 PNP Transistor U$42, U$ SC945 NPN Transistor U$41, U$43, U$45, U$46, U$47, U$48, U$49, U$50, U$51, U$52, U$53, U$54 2 4K7 Resistor R340, R uF 16v Electrolytic C189 Capacitor 5 10K Resistor R337, R344, R350, R351, R K Resistor R339, R341, R342, R346, R348, R349, R379, R n Polyester Capacitor C193, C /6.3 Electrolytic C205, C207 Capacitor 5 33K Resistor R343, R357, R359, R378, R K Resistor R369, R /16 Electrolytic C191 Capacitor 2 47K Resistor R371, R K Resistor R367, R K Resistor R352, R KA Pot CH-LEV, OH-LEV 3 100R Resistor R358, R361, R p Polyester Capacitor C206, C K Resistor R K Resistor R373, R R Resistor R354, R p Ceramic Capacitor C203, C204 1 HH-AC/TR 3 Pin Header SV12 2 MA02-2 Pin Header U$66, U$ TL072P OpAmp IC35
34 Step Eighteen: Accent Bill Of Materials Partlist exported from 808_production_Accent.sch at 5/10/ :15:37p Qty Value Device Parts 1 3mm LED AC-SEL 2.47/16 Electrolytic Capacitor C242, C243 11K Resistor R463 52N3904 NPN Transistor T2, T10, T16, T17, T18 34K7 Resistor R396, R397, R K Resistor R KB Pot ACCENT 122K Resistor R K Resistor R K Resistor R K Resistor R461, R R Resistor R400
2xVCX version 1.0. Calibration instructions can be found on the last page. Capacitor bypass MLCC X7R mm pin pitch
Produced by: Roll Your Own ljunggrenaudio.com Schematic & PCB Design by: KYMATICA DEVICES www.kymatica.com xvcx version.0 Bills Of Material Bold = PCB C C C3 C4 C5 C6 C7 C8 C9 C0 C C C3 C4 CON D D D3 D4
More informationD6, D7, D8, D9, D12, D13, D14, D15, D16, D17, D18, D19. Schottky rectifier diode. 1N5817-1N5819 or SB130
Roll Your Own ljunggrenaudio.com Altered States version 1.0 Bills Of Material Qty Value 12 1N4148 2 1N5818 4 1N750 4.7V 4 220p Device Diode Diode Zener diode Capacitor 30 100n 4 15p 8 560p 1 5x2 pin Capacitor
More informationLjunggren Audio Roll Your Own Penta
Ljunggren Audio Roll Your Own Penta Version: Penta 1.0 Bills Of Material Bold = PCB1, The rest = PCB2 Type Parts Des cription Pow er header Qty Value 1 2x5pin POWER Euro pow er connector Jack 1 3.5mm J1,
More informationopenqrp Transceiver Parts List By Functional Section 1/11/2014 Using openqrp PC Board Rev D, 40M Version
openqrp Transceiver Parts List By Functional Section 1/11/2014 Using openqrp PC Board Rev D, 40M Version Section 1 AGND Schematic Page 2 R37 [I8] 10K 1/8W Resistor (Brown Black Orange) R38 [J9] C80 [J9]
More informationNorcal Power/SWR Meter Assembly & Operating Manual. Revision 1D 10/15/2008
Norcal Power/SWR Meter Assembly & Operating Manual Revision 1D 10/15/2008 Copyright 2008 NorCal QRP Club Page 1 of 21 Contents CONTENTS...2 INTRODUCTION...3 SPECIFICATIONS...3 ASSEMBLY...4 OPERATING GUIDE...15
More informationMonoWave(X) Construction Guide Version 1.2. June 30th, 2018
MonoWave(X) Construction Guide Version 1.2 June 30th, 2018 1 of 10 Construction Construction of the MonoWave (X) is relatively straightforward and generally only requires good general soldering skills.
More informationLjunggren Audio Roll Your Own Optodist
Ljunggren Audio Roll Your Own Optodist Version: Optodist/VCA.0 Bill Of Material TYPE PART VALUE PCS NOTE Resistor R,R 0R Resistor R5,R0 K Resistor R3,R4 0K Resistor R,R9 68K Resistor R 00K Resistor R3
More informationWIRING THE HEATER POWER SUPPLY
WIRING THE HEATER POWER SUPPLY Fig. 14 13/14 Take the longer PS board (with the 47R resistors and the fuse) and, using M3x6 screws, fix it to the chassis to the left of the mains transformer. The diodes
More informationCLASSIC PEDAL KIT. Assembly Instructions WHEN YOU CAN T BUY IT BUILD IT. StewMac Monarch RARE / VINTAGE / HARD TO GET
Sheet #i-2205 Updated 2/8 StewMac Monarch CLASSIC PEDAL KIT Kit case is unpainted IN COLLABORATION WITH EarthQuakerDevices Assembly Instructions The Monarch Overdrive is an all discrete, FET-based dirt
More informationCAPI BB2521 Build Guide & BOM
This is a very simple build. I only have a few tips and things to look out for. I do recommend following these steps due to the diode/transistor relationship. 1. Install the three ceramic caps. If you
More informationTri Boost Kit Instructions
Tri Boost Kit Instructions Click here for older triboost version instructions(no 3-way LED) Parts Checklist...page 2-3 Schematic.....page 4 Populating and mounting the circuit board..page 5-14 Wiring Diagram.......page
More informationSERGE Variable Resonance Filter (VCFQ)
SERGE Variable Resonance Filter (VCFQ) The Random*Source version of the filter is an updated design that uses 3 high-end THAT280 VCAs for superior audio performance - a change that has been approved by
More informationIV-3 VFD Shield for Arduino. Assembly Manual
June 2014 Table of Contents 1 Overview Features Applications 3 3 3 2 Assembly Hints 4 3 PCB Overview 5 4 Circuit Diagram 6 5 Assembly Diodes and IC socket Electrolytic capacitors Ceramic capacitors 10K
More informationWhite Light CLASSIC PEDAL KIT. Assembly Instructions WHEN YOU CAN T BUY IT BUILD IT. StewMac RARE / VINTAGE / HARD TO GET
Sheet #i-2206 Updated 5/18 StewMac White Light CLASSIC PEDAL KIT Kit case is unpainted IN COLLABORATION WITH EarthQuakerDevices Assembly Instructions The White Light Overdrive is based on vintage overdrives
More informationPAT-4 TOROIDAL TRANSFORMER ASSEMBLY MANUAL
PAT-4 TOROIDAL TRANSFORMER ASSEMBLY MANUAL 2015 AkitikA, LLC All rights reserved Revision 1p3 August 22, 2015 Page 1 of 13 Table of Contents Table of Contents... 2 Table of Figures... 2 Section 1: About
More informationIDC-136II-KIT 136kHz DC RX Assembly Guide
IDC-136II-KIT 136kHz DC RX Assembly Guide ICAS Enterprises May 2 nd,2016 The IDC-136II-KIT is a 136kHz direct conversion receiver. Most of the SDR software can be used with this receiver. It is quite easy
More informationSimple Eurorack Row. Kit Builder's Guide. 4mspedals.com
Simple Eurorack Row Kit Builder's Guide 4mspedals.com ' Simple Eurorack Row This guide is for building a single-row eurorack case with a power supply. When completed, the case is ready to accept eurorack
More informationALARM KIT ESSENTIAL INFORMATION. Version 2.0 WHAT CAN YOU PROTECT WITH THIS
ESSENTIAL INFORMATION BUILD INSTRUCTIONS CHECKING YOUR PCB & FAULT-FINDING MECHANICAL DETAILS HOW THE KIT WORKS WHAT CAN YOU PROTECT WITH THIS ALARM KIT Version 2.0 Build Instructions Before you start,
More informationTRACE ELLIOT SERVICE MANUAL. DATE : December 29, 1999 Product Code: T0171/T0166/T0161 Model Number : BOXER65 98 BOXER30 98 BOXER15 98
TRACE ELLIOT SERVICE MANUAL DATE : December 29, 1999 Product Code: T0171/T0166/T0161 Model Number : BOXER65 98 BOXER30 98 BOXER15 98 Issued by: Trace Elliot Limited Blackwater Trading Estate The Causeway
More informationMudbunny ed. FX Type: Distortion 2012 madbeanpedals. 2 W x 1.65 H. Download previous version of the Mudbunny (before ).
Mudbunny - 2012 ed. FX Type: Distortion 2012 madbeanpedals 2 W x 1.65 H Download previous version of the Mudbunny (before 03.2012). The Mudbunny is an open-ended project in which you can create numerous
More informationAssembly Manual for New Control Board 22 June 2018
Assembly Manual for New Control Board 22 June 2018 Parts list Arduino 1 Arduino Pre-programmed 1 Faceplate Assorted Header Pins Full Board Rev A 9 104 capacitors 1 Rotary encode with switch 1 5-volt regulator
More informationez1081pre Mic Amplifier - Assembly manual [ Colourbook Issue 1]
ez1081pre Mic Amplifier - Assembly manual [ Colourbook Issue 1] ez1081pre Colourbook Contents. Section 1 - Colourbook assembly guide Section 2 - Setup and Calibration Section 3 - Schematics diagrams and
More informationFiveFish Studios PSU-2448Plus+ Assembly Guide
FiveFish Studios PSU-2448Plus+ Assembly Guide Copyright 2015-2017 FiveFish Audio Revision 1.02-20171105 No part of this document may be reproduced, either mechanically or electronically, posted online
More informationParts List DIY-81 rev 1. Capacitors. DIY-81 Project Parts list rev 1
Electrolytic C100 100 25 Axial 8 x 100uF/25V Axial C101 150 16 Axial 8 x 150uF/16V Axial C102 150 16 Axial 2 x 470uF/16V Radial C18 470 16 Radial C103 150 16 Axial C104 150 16 Axial C106 100 25 Axial C105
More informationLinear Stepper Driver v0.9.2 Assembly Instructions
Linear Stepper Driver v0.9.2 Assembly Instructions Here's what's included in the kit: 1x Printed Circuit board 1x Heatsink bracket 5x 0.1uF capacitors 1x 6-pin ISP header 1x 10-pin configuration header
More informationRGB Alarm Clock. -Color Alarm Clock-
RGB Alarm Clock -Color Alarm Clock- Table of Contents Preamble:...2 List of parts...3 Components...5 Parts and belongings...5 Clock Board Assembly...8 Identification of SMD parts:...0 The power supply
More informationCollosalus 2015 FX Type: Flanger 3.25 W x 2.9 H
Collosalus 2015 FX Type: Flanger Based on the MXR 117 Download the previous version documentation here: http://www.madbeanpedals.com/projects/collosalus/collosalus.zip 3.25 W x 2.9 H B.O.M. Resistors Caps
More informationELM327 OBD to RS232 Interpreter
OBD to RS232 Interpreter Description Almost all new automobiles produced today are required, by law, to provide an interface from which test equipment can obtain diagnostic information. The data transfer
More informationAssembly Instructions for the KA Electronics Flat MM Phono Preamplifier
Assembly Instructions for the KA Electronics Flat MM Phono Preamplifier Install IC sockets Flat MM Phono Preamp PC Board Stuffing Guide Place the PC Board on the bench silkscreen side face up. Drop six
More informationBill of Materials: Car Battery/charging system diagnostics PART NO
Car Battery/charging system diagnostics PART NO. 2192106 You can hook up the kit's test leads directly to the car battery (with engine off) and see whether battery voltage is ok (green LED on) or low (yellow
More informationwww MK-Electronic de EPSON LQ2170 Spares Guide Version 3 Page 1
REF PART NO DESCRIPTION REMARKS QTY 100 1025018 HOUSING ASSY., LOWER 1 101 1025039 COVER, FRONT 1 102 1025041 HOUSING, UPPER 1 103 1025027 COVER, PRINTER, REAR 1 104 1025024 COVER ASSY., PRINTER 1 105
More informationPOWER AMPLIFIER SERVICE MANUAL CONTENTS
POWER AMPLIFIER CONTENTS Performance Specifications... 2 Notes... 2 Rear Panel... 3 Section Location... 3 Block Diagram... 4 Interconnection Diagram... 5-8 Multi-channel Schematic and PCB... 9 Heatsink
More informationINSTRUCTIONS. DO NOT CONNECT TO MAINS POWER ( V AC).
P.O Box 578 Casino, NSW, 2470 Australia Phone: International ++614 2902 9083 Australia (04) 2902 9083 Website: http://rcs-rc.com E mail: Info@rcs-rc.com TABLE OF CONTENTS PROVIDED IN INSTRUCTIONS. Page
More informationSwitch Machines Installation & Wiring
Switch Machines Installation & Wiring Conventional Twin Coil Switch Machines Electrically: In use since developed by Walthers in early 1930 s Long time standard for remote operation Currently: Rix, Atlas,
More informationINSTRUCTIONS. DO NOT CONNECT TO MAINS POWER ( V AC).
P.O Box 578 Casino, NSW, 2470 Australia Phone: International ++614 2902 9083 Australia (04) 2902 9083 Website: http://rcs-rc.com E mail: Info@rcs-rc.com TABLE OF CONTENTS PROVIDED IN INSTRUCTIONS. Page
More informationFX TYPE: Distortion Based on the EHX Big Muff 2015 ed. madbeanpedals
Mudbunny FX TYPE: Distortion Based on the EHX Big Muff 2015 ed. madbeanpedals Download the previous version of the Mudbunny here: http://www.madbeanpedals.com/projects/mudbunny/docs/mudbunny.zip 1.95 W
More informationMONGOOSE. Introduction. < blueroomelectronics > Assembly Instructions. Mongoose was designed as an introduction to Mechatronics.
MONGOOSE Assembly Instructions Introduction Mongoose was designed as an introduction to Mechatronics Page 1 of 12 Before you start The Mongoose is a complex kit and skipping instructions is not advised,
More informationHW-8-LM386 Audio Amplifier Board Assembly Instructions
This LM386 based audio amplifier kit was designed to replace the small audio amplifier board in the Heathkit HW-8 transciever. The result is the ability to drive regular modern day 8 ohm headphones or
More informationAssembly Manual for ISDR-136-KIT
Assembly Manual for ISDR-136-KIT ICAS Enterprises Last Updated March 21 st, 2012 This SDR receiver kit is intended for the 136kHz band. The kit utilizes DIP IC components (no SMD) so that even a beginner
More informationLED PICTURE FRAME KIT
ESSENTIAL INFORMATION BUILD INSTRUCTIONS CHECKING YOUR PCB & FAULT-FINDING MECHANICAL DETAILS HOW THE KIT WORKS MAKE A DISPLAY OF YOUR MOST TREASURED PHOTOGRAPH WITH THIS LED PICTURE FRAME KIT Version
More informationsynthcube 291 VCF (buchla / verbos circuit realized by dustin stroh) module documents v2.0 06/20/2014 PCB rev 2.0 Errata:
synthcube 291 VCF (buchla / verbos circuit realized by dustin stroh) module documents v2.0 06/20/2014 PCB rev 2.0 Errata: copyright 2012 synthcube.com Page 1 Circuit Description A discussion thread about
More informationCTB-16K Hobbyist Line Kit 40 Amp 16 Channel Light Controller Assembly Manual *** Preliminary ***
CTB-16K Hobbyist Line Kit 40 Amp 16 Channel Light Controller Assembly Manual *** Preliminary *** Version 1.0 January 12, 2006 Copyright Light O Rama, Inc. 2006 Table of Contents 1 Introduction... 3 2 Required
More informationSMART LAB PUTTING TOGETHER THE
PUTTING TOGETHER THE SMART LAB INSTALLING THE SPRINGS The cardboard workbench with all the holes punched in it will form the base to the many cool circuits that you will build. The first step in transforming
More informationELM327 OBD to RS232 Interpreter
OBD to RS232 Interpreter Description Almost all new automobiles produced today are required, by law, to provide an interface from which test equipment can obtain diagnostic information. The data transfer
More informationINSTRUCTIONS. DO NOT CONNECT TO MAINS POWER ( V AC).
P.O Box 578 Casino, NSW, 2470 Australia Phone: International ++614 2902 9083 Australia (04) 2902 9083 Website: http://rcs-rc.com E mail: Info@rcs-rc.com ALPHA-3v2 Electronic Speed Controller Supplied for
More informationFX Type: Filter 2.35" W x 3.35" H Terms of Use: HoneyDripper HoneyDripper
HoneyDripper FX Type: Filter Based on the Colorsound Dipthonizer madbeanpedals 2015 Version Previous Versions: http://www.madbeanpedals.com/projects/archive/filtermod/ 2.35" W x 3.35" H Terms of Use: You
More informationBUMP AND SPIN KIT ESSENTIAL INFORMATION. Version 1.0 PROGRAM AND DESIGN YOUR OWN BUGGY WITH THIS
ESSENTIAL INFORMATION BUILD INSTRUCTIONS CHECKING YOUR PCB & FAULT-FINDING MECHANICAL DETAILS HOW THE KIT WORKS PROGRAM AND DESIGN YOUR OWN BUGGY WITH THIS BUMP AND SPIN KIT Version 1.0 Build Instructions
More informationMOTHMAN FUZZ ASSEMBLY INSTRUCTIONS RECOMMENDED TOOL AND SUPPLY LIST MOTHMAN FUZZ KIT PARTS LIST
MOTHMAN FUZZ ASSEMBLY INSTRUCTIONS Thank you for purchasing the J201 Clean Boost Pedal Kit from Mammoth Electronics! This is a intermediate level kit that and we have made every effort to make the assembly
More informationAssembly and User Guide
Assembly and User Guide 2 Amp Adjustable Electronic Load 30V and 20 Watts Max Powered by: 9V Battery Pico Load is a convenient constant current load for testing batteries and power supplies. The digital
More informationBuild Instructions and User Guide
Build Instructions and User Guide Getting Started To build the Rock Drill 4069 you will need: Solder Wire Cutters Soldering Iron Small pliers The kit is suitable for beginners or more experienced builders
More informationSoldering Pi2Go Lite. Soldering the Line-Follower PCB
Soldering Pi2Go Lite First check which version of the main PCB you have. It is marked above the left motor "Pi2Go-Lite v1.x". There are minor changes to some parts of the build. v1.0 (initial release)
More information~Dashboard Digital Voltmeter~
~Dashboard Digital Voltmeter~...November, 2002 This project is helpful to anyone who drives an automobile. I had found this project at the local libary... in an old publication. I made it and it worked
More informationEurorack 1A Power Supply
Eurorack 1A Power Supply Thank you for building the classic linear Eurorack 1A Power Supply. Linear power supplies are a bit old school but they still offer a very good solution for high end synthesizers.
More informationTHREE PHASE FAULT ANALYSIS WITH AUTO RESET ON TEMPORARY FAULT AND PERMANENT TRIP OTHERWISE
THREE PHASE FAULT ANALYSIS WITH AUTO RESET ON TEMPORARY FAULT AND PERMANENT TRIP OTHERWISE ABSTRACT The project is designed to develop an automatic tripping mechanism for the three phase supply system.
More informationASSEMBLY INSTRUCTIONS FOR NEW FK109 4 LED Railroad Crossing Flasher Kit WITH ADJUSTABLE FLASHING SPEED CONTROL with 4 Red 3mm Leds
ASSEMBLY INSTRUCTIONS FOR NEW FK109 4 LED Railroad Crossing Flasher Kit WITH ADJUSTABLE FLASHING SPEED CONTROL with 4 Red 3mm Leds Description: Very easy to build, The FK109 Led Flasher kit makes the perfect
More informationIV-11 VFD tube clock Assembly instructions v1.2.2
IV-11 VFD tube clock Assembly instructions v1.2.2 Designer: Website: E-mail: Yan Zeyuan. China http://www.nixieclock.org yanzeyuan@qq.com 2017-01-26 NCH Attention Attention: Warning: Warning: Warning:
More informationTIMER PROJECT KIT ESSENTIAL INFORMATION. Version 2.0 TIME SOMETHING WITH THIS
ESSENTIAL INFORMATION BUILD INSTRUCTIONS CHECKING YOUR PCB & FAULT-FINDING MECHANICAL DETAILS HOW THE KIT WORKS TIME SOMETHING WITH THIS TIMER PROJECT KIT Version 2.0 Build Instructions Before you start,
More informationSM361 RIG SWITCH CONSTRUCTION MANUAL
SM361 RIG SWITCH CONSTRUCTION MANUAL Document ver 1, For software release ver 1.1 May 27, 2016 Controls the power of 12V equipment while a vehicle is in use Product Development by: SM361 RIG SWITCH OVERVIEW
More information0-28 vdc stabilized power supply with current control Amp
0-28 vdc stabilized power supply with current control 0.002-10 Amp General Description This is a high quality power supply with a continuously variable stabilised output adjustable at any value between
More informationTotal solder points: 187 Difficulty level: beginner advanced. Code lock K6400 ILLUSTRATED ASSEMBLY MANUAL
Total solder points: 187 Difficulty level: beginner 1 2 3 4 5 advanced Code lock K6400 Ged rid of those old fashioned keys ILLUSTRATED ASSEMBLY MANUAL H6400IP-2 Features & Specifications Features: More
More informationPOWER SUPPLY MODEL XP-800. TWO AC VARIABLE VOLTAGES; 0-120V and 7A, PLUS UP TO 10A. Instruction Manual. Elenco Electronics, Inc.
POWER SUPPLY MODEL XP-800 TWO AC VARIABLE VOLTAGES; 0-120V and 0-40V @ 7A, PLUS 0-28VDC @ UP TO 10A Instruction Manual Elenco Electronics, Inc. Copyright 1991 Elenco Electronics, Inc. Revised 2002 REV-I
More informationPacMan BoB QA Test Plan
PACMAN BOB QA TEST PLAN 1 PacMan BoB QA Test Plan ECE 492 Spring 2014 Latest Revision: 18 April 2014 Prepared by: Drew Jeffrey Abstract This document covers the plan of testing to ensure the Pack Manager
More informationChapter 2. Battery Charger and Base Assembly
Chapter 2 Battery Charger and Base Assembly 11 CHAPTER 2. BATTERY CHARGER AND BASE ASSEMBLY 2.1 Section Overview This Lab teaches students how to assemble a Tekbot, in the following steps: Describe the
More informationArlo Power Distribution Board Kit Rev B (#28996)
Web Site: www.parallax.com Forums: forums.parallax.com Sales: sales@parallax.com Technical: support@parallax.com Office: (916) 624-8333 Fax: (916) 624-8003 Sales: (888) 512-1024 Tech Support: (888) 997-8267
More informationThe ability to make basic voltage and resistance measurements using a digital multimeter
Seventh Circle Audio C84 Microphone Preamp Based on the innovative Double Balanced Microphone Amplifier circuit published by Graham John Cohen in 1984, the C84 microphone preamp offers exceptional performance
More informationQUASAR ELECTRONICS KIT No ELECTRONIC CAR IGNITION
QUASAR ELECTRONICS KIT No. 1058 ELECTRONIC CAR IGNITION General Description The advantages of having an electronic ignition in your car are well known. Let us mention them again: 1. Perfect burning of
More informationCHRISTMAS TREE KIT MODEL K-14. Assembly and Instruction Manual ELENCO
CHRISTMAS TREE KIT MODEL K-14 Assembly and Instruction Manual ELENCO Copyright 2015, 1989 by Elenco Electronics, Inc. All rights reserved. Revised 2015 REV-J 753214 No part of this book shall be reproduced
More informationEngineering Innovation Center EIC. Electronic Component Selection
Electronic Component Selection Why is it important to choose the right part? Cost Efficiency This PCB fire caused by choosing the wrong capacitor Cap wasn t rated for voltage and failed short >100 Amps
More informationTotal solder points: 20 Difficulty level: beginner advanced UNIVERSAL BATTERY CHARGER K7302 ILLUSTRATED ASSEMBLY MANUAL
Total solder points: 20 Difficulty level: beginner 1 2 3 4 5 advanced UNIVERSAL BATTERY CHARGER K7302 Low cost soluton for charging of both NiCd and NiMh batteries. ILLUSTRATED ASSEMBLY MANUAL H7302IP-1
More informationGeneral Purpose Flasher Circuit
General Purpose Flasher Circuit By David King Background Flashing lights can be found in many locations in our neighbourhoods, from the flashing red light over a stop sign, a yellow warning light located
More informationFeatures Block Diagram Specifications Typical Wiring Diagram Connection and Adjustment Locations...3 4
SUESTEP STP-DV-4035 MICOSTEPPING DIVE CHAPTE 3 In This Chapter... Features.......................................32 Block Diagram...................................32 Specifications...................................33
More informationDECIDUOUS FILTER ASSEMBLY INSTRUCTIONS RECOMMENDED TOOL AND SUPPLY LIST DECIDUOUS FILTER KIT PARTS LIST
DECIDUOUS FILTER ASSEMBLY INSTRUCTIONS Thank you for purchasing the Deciduous Filter Effect Pedal Kit from Mammoth Electronics! This is an intermediate level kit and we have made every effort to make the
More information802C System Controller Original and SMD Version
802C System Controller Original and SMD Version Units with serial numbers beginning with 100000 are the original 802C's. Units with serial numbers beginning with 200000 are the new SMD 802C's. 1997 Bose
More informationProfessional Wireless Products
Page 1 of 6 093115 Communications Power Supply and Battery Management Controller Page 2 of 6 1.0 Introduction The 093115 is a 13.8 volt 15amp transformer isolated switch mode down converter designed to
More informationBill Of Material MIXER AMIS - ZRM4
8 PCB Line S5701 S5702 S5703 AMIS - ZRM4 PCB (6336) SUB ASSLY. S5701 2020030503 HOS(T)/ALPHA - POT. 9mm,SEALED RD901-20-15K-B54/B50K BLK. NUT (RD 2111220101 RESISTOR M.O.R., 2W, 5%, 100 OHMS (#RSS) RoHS
More informationFX TYPE: DISTORTION Based on the Suhr Riot PCB artwork m2011 madbeanpedals Special thanks to culturejam! Release date: REVISED
http://www.madbeanpedals.com presents uproar FX TYPE: DISTORTION Based on the Suhr Riot PCB artwork m2011 madbeanpedals Special thanks to culturejam! Release date: 01.30.11 REVISED 02.08.11 This version
More informationPPS20 COMMUNICATIONS POWER SUPPLY AND BATTERY MANAGEMENT SYSTEM
PPS20 COMMUNICATIONS POWER SUPPLY AND BATTERY MANAGEMENT SYSTEM 2 Table of Contents Introduction:... 3 1.0: Operation Principles:... 3 1.1: Stand alone supply... 3 1.2: Backed up supply:... 3 1.3: Battery
More informationICA Manufacturing Catalog. Your One Stop Metal Shop. Table of Contents. Visit us at:
ICA Manufacturing Your One Stop Metal Shop At ICA Manufacturing, you will find high-quality creations and wholesale parts at a budget price. From Aluminum Cabinetry, to Transformers, to Capacitors, we
More informationDisaster Transport CLASSIC PEDAL KIT. Assembly Instructions WHEN YOU CAN T BUY IT BUILD IT. StewMac RARE / VINTAGE / HARD TO GET
StewMac Sheet #i-2203 Updated 5/8 Disaster Transport CLASSIC PEDAL KIT Kit case is unpainted IN COLLABORATION WITH EarthQuakerDevices Assembly Instructions The Disaster Transport is an analog voiced digital
More informationCHAPTER 2. Current and Voltage
CHAPTER 2 Current and Voltage The primary objective of this laboratory exercise is to familiarize the reader with two common laboratory instruments that will be used throughout the rest of this text. In
More informationDIY Synth Kit - Manual STUTTER SYNTH
DIY Synth Kit - Manual STUTTER SYNTH Welcome to the DIY Synth - Manual This is a step-by-step guide to making your own electronic Synth. All you will need is your hands and your DIY Synth kit which includes
More informationEQ73 Parts list Reference Value Qty Description Marking Dim Manuf. YEL-VIO-BLK-GLD-BRN RED-RED-BRN-BRN RED-RED-BLK-BLK-BRN GRN-BLU-BRN-BRN
EQ73 Parts list (1) Reference Value Qty Description Marking Dim (2) Manuf. R52, R53 47R 2 Resistor 1%, 1/4W YEL-VIO-BLK-GLD-BRN R45, R46 180R 2 Resistor 5%, 1/2W R23, R24 220R 2 Resistor 1%, 1/4W RED-RED-BRN-BRN
More informationTotal solder points: 93 Difficulty level: beginner advanced 10 LED MONO VU METER K4304 ILLUSTRATED ASSEMBLY MANUAL
Total solder points: 93 Difficulty level: beginner 1 2 3 4 5 advanced 10 LED MONO VU METER K4304 Add a visual readout to your existing or new equipment. ILLUSTRATED ASSEMBLY MANUAL H4304IP-1 Features &
More informationAMM-TE ammeter Manual
AMM-TE ammeter Manual I. Kit Details Kit Name: Ammeter Kit Kit Model: AMM-TE PCB Size: 70.6 * 39mm Screen size: 51 * 24mm Electrical parameters Operating voltage: DC5 Operating Current: 35mA Accuracy:
More informationSilvertel. Ag Features. 2. Description. Power-Over-Ethernet Module. IEEE802.3af compliant. Small SIL and SMT package available
Silvertel V2.2 Jan 2015 Datasheet Ag9700 Pb 1. Features IEEE802.3af compliant Small SIL and SMT package available Low cost, with minimal external components required Input voltage range 36V to 57V Short-circuit
More informationThe ability to make basic voltage and resistance measurements using a digital multimeter
Seventh Circle Audio N72 Microphone Preamp Based on the BA183 amplifier circuit used in the 1066, 1073, 1272, and other Neve console modules, the N72 microphone preamp will deliver the same immediately
More informationConnecting the rear fog light on the A4 Jetta, while keeping the 5 Light Mod
Connecting the rear fog light on the A4 Jetta, while keeping the 5 Light Mod DISCLAIMER: I'm human and make mistakes. If you spot one in this how to, tell me and I'll fix it This was done on my 99.5 Jetta.
More informationArlo Power Distribution Board Kit Rev B (#28996)
Web Site: www.parallax.com Forums: forums.parallax.com Sales: sales@parallax.com Technical: support@parallax.com Office: (916) 624-8333 Fax: (916) 624-8003 Sales: (888) 512-1024 Tech Support: (888) 997-8267
More informationDoubloon Two Bus Power Supply
Doubloon Two Bus Power Supply Augustica w w w. a u g u s t i c a. c o m DANGER This power supply kit uses high-voltage and therefore may produce a lethal shock. Only persons who are competent at electronics
More informationMARK I. Maintenance and repair information.
MARK I Maintenance and repair information. 1 Malfunctions can be cured easily when a proper diagnosis of the fault is made. Usually only one part (most often a tube) is all that has gone bad, and the Boogie
More informationIn this installment we will look at a number of things that you can do with LEDs on your layout. These will include:
Introduction The first article in this series, LEDs 101 - The Basics, served to review the characteristics and use of LED lighting in a garden railway environment. It also generated a host of questions
More informationTotal solder points: 126 Difficulty level: beginner advanced POWER DIMMER 230V) K8038 ILLUSTRATED ASSEMBLY MANUAL
Total solder points: 126 Difficulty level: beginner 1 2 3 4 5 advanced POWER DIMMER (1KW @ 230V) K8038 NOISE SUPPRESSED ACCORDING TO EN55015 Class microcontroller high power dimmer with non volatile memory
More informationC capacitance, 91 capacitors, codes for, 283 coupling, polarized and nonpolarized,
Index Numbers and Symbols 555 timer, 164 166 making sound using, setting output speed of, 166 167 using for reaction game speed, 260 261 μf (microfarad), 92 Ω (ohms), 7, 70 A A (amperes), 7 AC (alternating
More informationHW-8-LM386 Audio Amplifier Board Assembly Instructions
This LM386 based audio amplifier kit was designed to replace the small audio amplifier board in the Heathkit HW-8 transciever. The result is the ability to drive regular modern day 8 ohm headphones or
More information3 Slot Payphone Controller
S Coin Controller 2A Information on your Telephone For Your Records Manufacturer Date of Original Manufacture Drawing Reference One of the original patents --- US 2,043,201 This Telephone is Property of
More informationHarbach Soft Key (sk-220) Installation Instructions for the Heathkit SB-220
Harbach Soft Key (sk-220) Installation Instructions for the Heathkit SB-220 Step-by-Step Instructions with Photos Based on an install by W4HDM Installation & Photos by W4HDM Instructions from http://www.harbachelectronics.com/
More informationINSTALLING THE #OMEGA-3v9s ESC.
- 2 - INSTALLING THE #OMEGA-3v9s ESC. We usually supply the # OMEGA-3v9s ESC with a Lemon brand Rx which is simply plugged in upside down on the ESC pcb in the 24 pin socket. The two parts are bench tested
More informationAssembly notes for RFX Nano 3.0 carrier board
Assembly notes for RFX Nano 3.0 carrier board Mark Pendrith , Dec 2014. Basic kit parts (BOM) 1 PCB mount 5mm/2.1mm DC barrel jack (see note below) 1 LD1117v33 (either TO-220
More information100W SUBWOOFER KIT. Total solder points: 383 Difficulty level: beginner advanced K8077 ILLUSTRATED ASSEMBLY MANUAL
100W SUBWOOFER KIT Powerful bass from a small cabinet thanks to the dual speaker principle Total solder points: 383 Difficulty level: beginner 1 2 3 4 5 advanced K8077 ILLUSTRATED ASSEMBLY MANUAL H8077IP-1
More informationLow Voltage 3-Phase Induction Motors. Range 0.18kW to 670kW
Low Voltage 3-Phase Induction Motors Range 0.18kW to 670kW Totally Enclosed Fan-Cooled Cast Iron Series Contents page page PRODUCT DETAILS General Information 2 Electrical Design and Standards Altitude
More information