openqrp Transceiver Parts List By Functional Section 1/11/2014 Using openqrp PC Board Rev D, 40M Version
|
|
|
- Erika Nash
- 6 years ago
- Views:
Transcription
1 openqrp Transceiver Parts List By Functional Section 1/11/2014 Using openqrp PC Board Rev D, 40M Version Section 1 AGND Schematic Page 2 R37 [I8] 10K 1/8W Resistor (Brown Black Orange) R38 [J9] C80 [J9] 22uF Tantalum Capacitor C79 [J9].1uF Ceramic Capacitor (104) Section 2-12 V Input Schematic Page 3 J3 [E11] Power Connector D1 [D11] 1N4001 Power Diode C92 [G8] 220uF Electrolytic Capacitor C85 [F10].1uF Ceramic Capacitor (104) C56 [C3] 100uF Electrolytic Capacitor Section 3 - Digital 5V Schematic Page 3 VR2 [F2] LM78L05 5 volt Regulator (TO-220) C51 [F2].1uF Ceramic Capacitor (104) C50 [F3] 100uF Electrolytic Capacitor Section 4 - Analog 6V Schematic Page 2 VR3 [G9] LM78L06 6 volt Regulator (TO-92) C91 [G8].1uF Ceramic Capacitor (104) C93 [A1] C88 [G9] 100uF Electrolytic Capacitor Section 5 - Analog 8V Schematic Page 4 VR1 [D7] LM78L08 TO92 8 volt Regulator (TO-92) C31 [D7].1uF Ceramic Capacitor (104) C33 [D8] C30 [D8] 33uF Electrolytic Capacitor Section 6 - Arduino CPU Schematic Page 8 & 9 R3 [C4] 4.7K 1/8W Resistor (Yellow Violet Red) R5 [D4] R14 [D5] R24 [D6] R53 [E1] R48 [E3] R16 [D6] 10K 1/8W Resistor (Brown Black Orange) R6 [D4] R29 [F5] 1K 1/8W Resistor (Brown Black Red) R54 [G1] 2.2K 1/8W Resistor (Red Red Red) R55 [H1] R56 [I1] R57 [J1] R2 [C2] 22K 1/8W Resistor (Red Red Orange) C46 [E4] 22pF Ceramic capacitor C47 [E4] C46A [E3].1uF Ceramic Capacitor (104) C55 [D4]
2 C52 [F1].001uF Ceramic Disc Capacitor (102) C54 [D3] C86 [F10] C87 [F10] U2S1 [E2] 28 pin DIP socket Socket for CPU (In IC package) Y2 [E4] MHz Crystal LED1 [E6] LED Red LED J1 [C4] 2x3 Header ICSP Connector 6 pin dual header J4 [F11] Stereo 1/8 Paddle connector S1 [E1] SPST Pushbutton Switch S2 [F1] S3 [F1] S4 [G1] S5 [H1] S6 [I1] U2 [E2] ATmega168 CPU 28 pin DIP (In IC package) Section 7 - LCD Display Schematic Page 7 C53 [E1].1uF Ceramic Capacitor (104) RX2 [D2] 10K Trimmer Potentiometer (Contrast) R1 [C1] 47Ω 1/4W Resistor (Red Violet Black) DP1 [A1] LCD Display Sunlike 1602SD Section 8 - VFO Schematic Page 4 Q9 [E8] 2N4401 NPN Transistor (TO-92) R25 [E8] 47K 1/8W Resistor (Yellow Violet Orange) R31 [F8] 22K 1/8W Resistor (Red Red Orange) R32 [F9] 2.2K 1/8W Resistor (Red Red Red) R30 [E7] 1M 1/8W Resistor (Brown Black Blue) C16 [C8] 10pF Ceramic Capacitor (10) C43 [F7].01uF Ceramic Capacitor (103) C36 [F9] 1000pF Polystyrene Capacitor C38 [F8] C37 [F9] 2700pF Polystyrene Capacitor C34 [E9] 220pF Ceramic Capacitor (221) C41 [F8] C35 [E9] 150pF Ceramic Capacitor (151) C40 [F8] VC1 [E8] MVAM109 Varactor Diode L5 [E9] T50-6 Toroid Core 6.0 uh 37 turns #28 (large yellow) Section 9 - VFO Buffer Schematic Page 5 R26 [D7] 100K 1/8W Resistor (Brown Black Yellow) R27 [D7] R15 [D6] 2.2K 1/8W Resistor (Red Red Red) R28 [D6] 1K 1/8W Resistor (Brown Black Red) C32 [D7].01uF Ceramic Disk Capacitor (103) C39 [E8] 22pF Ceramic Capacitor C42 [E7] 10pF Ceramic Disk Capacitor (10) C44 [E6] 10pF Ceramic Disk Capacitor (10) Q10 [E7] 2N4401 NPN Transistor (TO-92)
3 Q11 [E7] Section 10 - Tune/RIT Controls Schematic Page 5 R52 [G3] 1.5K 1/8W Resistor (Brown Green Red) R47 [G4] 2.2K 1/8W Resistor (Red Red Red) R49 [G3] 3.9K 1/8W Resistor (Orange White Red) R50 [G2] 7.5K 1/8W Resistor (Violet Green Red) R51 [G3] 33K 1/8W Resistor (Orange Orange Orange) RP1 [na] 10K (TUNE) 10 Turn 10K Potentiometer (Control Pack) RP2 [na] 10K (RIT) 10K Potentiometer (Control Pack) C45 [F5].01uF Ceramic Disk Cap (103).2 spacing U4 [G5] CD pin DIP (In IC Package) Section 11 - TX Keyed 12V Schematic Page 6 R4 [C4] 4.7K 1/8W Resistor (Yellow Violet Red) R12 [C6] R13 [C6] 10K 1/8W Resistor (Brown Black Orange) C3 [B2].1uF Ceramic Capacitor (104) C15 [C7] 2.2uF Electrolytic Capacitor Q3 [C6] 2N7000 MOSFET transistor (TO-92) Q4 [C7] 2N4403 PNP transistor (TO-92) R8 [A4] 150Ω 1/4W Resistor (Brown Green Brown) ZD1 [B2] 7.5V 1N5236 Zener Diode Section 12 - TX Mixer/1st Driver Schematic Page 6 R11 [A6] 100Ω 1/4W Resistor (Brown Black Brown) R7 [A5] 150Ω 1/4W Resistor (Brown Green Brown) R10 [B6] 5.6K 1/8W Resistor (Green Blue Red) R9 [B6] 10K 1/8W Resistor (Brown Black Orange) C7 [A4] 2.2pF Ceramic Disk Capacitor (2.2) C1 [A3] 150pF Ceramic Disk Capacitor (151) C2 [A3] 47pF Ceramic Disk Capacitor (470) C6 [A4] 56pF COG Multilayer Ceramic Capacitor (560) C8 [A5] C10 [A6] 120pf NPO Ceramic Disk Capacitor (121) C11 [A6] 220pF Multilayer Ceramic (221) C4 [C2] 680pF Ceramic Disk Capacitor (681) C5 [C3].01uF Ceramic Disk Capacitor (103) C9 [A5].1uF Ceramic Capacitor (104) CT1 [A2] 9-90pF Trimmer Capacitor L1 [A3] 47uH Inductor U1 [B3] NE602A Mixer (DIP8) (In IC package) Q1 [A6] 2N2222A NPN Transistor (TO-18) Y1 [B2] MHz Crystal T1 [B4] 42IF123 IF Transformer (10.7 MHz) T2 [B5] Section 13 - PSoC Controller Schematic Page 3 R45 [G4] 22K 1/8W Resistor (Red Red Orange) C49 [F3].1uF Ceramic Capacitor (104) C48 [F5].1uF Mylar Capacitor (104) Brown,.2 U3 [G4] CY8C27143 PSoC (DIP8) (In IC package)
4 U3S [G4] 8 pin socket DIP8 (In IC package) Section 14 - Low Pass Filter / Rx Antenna Switch Schematic Page 7 R23 [C9] 22k 1/8W Resistor (Red Red Orange) C21 [A10] 220pF Multilayer Ceramic 200V (221) C27 [B11] C20 [A10] 680pF Multilayer Ceramic 200V (681) C23 [A10] C26 [B10] C24 [B11] C25 [B10].001uF Ceramic Disc Capacitor (102) C29 [C9] L2 [A10] T uH 17 turns #24 L3 [B11] Q7 [C10] 2N7000 MOSFET transistor (TO-92) Q8 [C10] Q6 [B10] ZVNL110A MOSFET transistor (TO-92E) J2 [C11] BNC RF Connector PCB Mount (Control Pack) RP3 [na] 5K (RF Gain) 5K Potentiometer (Control Pack) Section 15 - Audio Amplifier Schematic Page 3 C94 [H10].01uF Ceramic Disk Capacitor (103) C81 [J10] 1uF Tantalum Capacitor (105) C82 [I9].1uF Ceramic Capacitor (104) C83 [H9].1uF Ceramic Capacitor (104) C84 [G10] 100uF Electrolytic Capacitor R33 [G10] 2.2Ω 1/4W Resistor (Red Red Gold) R34 [H9] 27K 1/8W Resistor (Red Violet Orange) RX3 [J10] 5K Trimmer Potentiometer (AF Gain) J5 [H11] Stereo 1/8 Speaker connector U8 [H10] TDA7052A Audio Amp (DIP8) (In IC package) Section 16 - Active Filter Schematic Page 2 U7 [I8] TS922A Dual Op Amp (DIP8) (In IC package) R36 [H8] 66.5K 1/8W 1% Resistor R42 [G7] 16.5K 1/8W 1% Resistor R35 [H8] 8.26K 1/8W 1% Resistor R46 [F4] 1M 1/8W Resistor (Brown Black Green) C89 [H8].012uF Mylar Capacitor C90 [G8] Section 17 - Receiver Input Filter, Schematic Page 1 1st Rx Mixer, and Crystal Filter Part 1 C60 [H3].1uF Ceramic Capacitor (104) C61 [H4] 47pF Ceramic Disk Capacitor (470) C57 [I2] 56pF Ceramic Capacitor (560) C59 [H3] C58 [I3] 2.2pF Ceramic Capacitor (2.1) C66 [H5] 39pF Ceramic Capacitor (390) C67 [I4] 220pF Ceramic Capacitor (221) C69 [J5]
5 C71 [I5] C68 [J4] 150pF Ceramic Capacitor (151) C70 [J5] L6 [H5] 10uH Inductor L7 [I5] U5 [H4] NE602A Mixer (DIP8) (In IC package) Part 2 Y4 [J4] MHz Crystal Y5 [J4] Y6 [J5] Y7 [J6] T4 [H3] 42IF123 IF Transformer (10.7 MHz) T5 [J3] Cxx [H3].001uF Ceramic Disc Capacitor (102) Section 18-2nd Rx Mixer and Diff Amp Schematic Page 1 R44 [I5] 470Ω 1/8W Resistor (Yellow Violet Brown) R40 [I7] 4.7K 1/8W Resistor (Yellow Violet Red) R43 [J6] R39 [J8] 470K 1/8W Resistor (Yellow Violet Yellow) R41 [J7] C72 [I6].01uF Ceramic Disk Capacitor (103) C73 [H6].01uF Mylar Capacitor (103) Brown C74 [I6].1uF Mylar Capacitor (104) Brown C75 [I7] C62 [H5] 47pF Ceramic Disk Capacitor (470) C63 [H6] 220pF Ceramic Disk Capacitor (221) C78 [J8] 150pF Multilayer Ceramic Capacitor (151) C77 [J7] C64 [H5].1uF Ceramic Capacitor (104) C76 [H7] C65 [H5] 22uF Tantalum Capacitor CT2 [H7] 9-90pF Trimmer Capacitor D2 [J7] 1N4148 Silicon Diode D3 [J7] U6 [H6] NE602A Mixer (DIP8) (In IC package) Y3 [G6] MHz Crystal Section 19 - Tx 2nd Driver/Final Schematic Page 7 Q5 [A9] IRF510 Power MOSFET (TO-220) R19 [B7] 4.7K 1/8W Resistor (Yellow Violet Red) R20 [A4] 2.2K 1/8W Resistor (Red Red Red) R18 [B7] 1K 1/8W Resistor (Brown Black Red) R21 [A7] 22Ω 1/4W Resistor (Red Red Black) R22 [A9] 10Ω 1/8W Resistor (Brown Black Black) C12 [B6].01uF Ceramic Disk Capacitor (103) C14 [B7] 56pF NPO Ceramic Capacitor (560) C13 [A8].1uF Ceramic Capacitor (104) C18 [A9] C22 [A10].1uF Ceramic Capacitor (104) C28 [B9]
6 C19 [B9].001uF Ceramic Capacitor (102) C17 [C9] 220uF Electrolytic Capacitor Q2 [A7] 2N2219A NPN Transistor (TO-39) T3 [B8] 42IF123 IF Transformer (10.7 MHz) RX1 [A8] 5K Trimmer Pot (Transmit Bias) L4 [A9] FT turns bifilar winding #24 Control Pack Knob Qty 3 - Tuning, RIT, RF Gain Poteniometer Qty 1 - Single turn 5K Pot Poteniometer Qty 1 - Single turn 10K Pot Poteniometer Qty 1-10 turn 10K Pot BNC Qty 1 - BNC Connector PCB mount Miscellaneous Copper Wire #24 33 inches Low pass filter and final toroids Copper Wire #28 21 inches VFO toroid Enclosure Qty 1 Heat Sink Bracket Qty 1 Rubber Feet Qty x ¼ Screws Black Qty 4 For enclosure cover 4-40 x 3/8 Screws Qty 4 For PCB mounting TO220 Insulator Qty 1 For heat sink TO220 Shoulder Washer Qty 1 For heat sink 4-40 x ¼ Screw Qty 2 For heat sink bracket 4-40 Nut w/lock Washer Qty 1 For heat sink bracket Insulated Wire 20 inches Control Wiring IC Pack NE602/610 Qty 3 8 pin DIP TS922A Qty 1 8 pin DIP CD4066 Qty 1 14 pin DIP TD7052A Qty 1 8 pin DIP Atmega168 Qty 1 28 pin DIP CY8C27143 (PsoC) Qty 1 8 pin DIP 14 pin socket Qty 2 8 pin socket Qty 1
7 Parts Placement Guide
IDC-136II-KIT 136kHz DC RX Assembly Guide
IDC-136II-KIT 136kHz DC RX Assembly Guide ICAS Enterprises May 2 nd,2016 The IDC-136II-KIT is a 136kHz direct conversion receiver. Most of the SDR software can be used with this receiver. It is quite easy
HW-8-LM386 Audio Amplifier Board Assembly Instructions
This LM386 based audio amplifier kit was designed to replace the small audio amplifier board in the Heathkit HW-8 transciever. The result is the ability to drive regular modern day 8 ohm headphones or
HW-8-LM386 Audio Amplifier Board Assembly Instructions
This LM386 based audio amplifier kit was designed to replace the small audio amplifier board in the Heathkit HW-8 transciever. The result is the ability to drive regular modern day 8 ohm headphones or
Norcal Power/SWR Meter Assembly & Operating Manual. Revision 1D 10/15/2008
Norcal Power/SWR Meter Assembly & Operating Manual Revision 1D 10/15/2008 Copyright 2008 NorCal QRP Club Page 1 of 21 Contents CONTENTS...2 INTRODUCTION...3 SPECIFICATIONS...3 ASSEMBLY...4 OPERATING GUIDE...15
Assembly Manual for New Control Board 22 June 2018
Assembly Manual for New Control Board 22 June 2018 Parts list Arduino 1 Arduino Pre-programmed 1 Faceplate Assorted Header Pins Full Board Rev A 9 104 capacitors 1 Rotary encode with switch 1 5-volt regulator
Assembly Manual for ISDR-136-KIT
Assembly Manual for ISDR-136-KIT ICAS Enterprises Last Updated March 21 st, 2012 This SDR receiver kit is intended for the 136kHz band. The kit utilizes DIP IC components (no SMD) so that even a beginner
ez1081pre Mic Amplifier - Assembly manual [ Colourbook Issue 1]
![ez1081pre Mic Amplifier - Assembly manual [ Colourbook Issue 1]](/thumbs/90/103906919.jpg "ez1081pre Mic Amplifier - Assembly manual [ Colourbook Issue 1]")
ez1081pre Mic Amplifier - Assembly manual [ Colourbook Issue 1] ez1081pre Colourbook Contents. Section 1 - Colourbook assembly guide Section 2 - Setup and Calibration Section 3 - Schematics diagrams and
Ljunggren Audio Roll Your Own Penta
Ljunggren Audio Roll Your Own Penta Version: Penta 1.0 Bills Of Material Bold = PCB1, The rest = PCB2 Type Parts Des cription Pow er header Qty Value 1 2x5pin POWER Euro pow er connector Jack 1 3.5mm J1,
POWER AMPLIFIER SERVICE MANUAL CONTENTS
POWER AMPLIFIER CONTENTS Performance Specifications... 2 Notes... 2 Rear Panel... 3 Section Location... 3 Block Diagram... 4 Interconnection Diagram... 5-8 Multi-channel Schematic and PCB... 9 Heatsink
ITEM PART NO DESCRIPTION QTY LOCATION
TRANSISTOR 1 01-24001A0-A00 DIODE WIN4001 1 D206 2 01-3197130-A00 TRANSISTOR 2SC1971 1 Q2 3 01-320533A-A00 TRANSISTOR 2SC2053 1 Q3 4 01-3240830-A00 TRANSISTOR 2SC2408 1 Q4 SMT TRANSISTOR 1 02-22838D0-A00
Assembly Instructions
Assembly Instructions for the PA3 3.1 MHz Switch Mode Plasma Tube Amplifier Kit PA3 Amplifier shown mounted on HS2 Heat Sink (The HS2 shown here is not included with this kit.) Manual v1.01 30 September
ICA Manufacturing Catalog. Your One Stop Metal Shop. Table of Contents. Visit us at:
ICA Manufacturing Your One Stop Metal Shop At ICA Manufacturing, you will find high-quality creations and wholesale parts at a budget price. From Aluminum Cabinetry, to Transformers, to Capacitors, we
IV-11 VFD tube clock Assembly instructions v1.2.2
IV-11 VFD tube clock Assembly instructions v1.2.2 Designer: Website: E-mail: Yan Zeyuan. China http://www.nixieclock.org yanzeyuan@qq.com 2017-01-26 NCH Attention Attention: Warning: Warning: Warning:
AMM-TE ammeter Manual
AMM-TE ammeter Manual I. Kit Details Kit Name: Ammeter Kit Kit Model: AMM-TE PCB Size: 70.6 * 39mm Screen size: 51 * 24mm Electrical parameters Operating voltage: DC5 Operating Current: 35mA Accuracy:
802C System Controller Original and SMD Version
802C System Controller Original and SMD Version Units with serial numbers beginning with 100000 are the original 802C's. Units with serial numbers beginning with 200000 are the new SMD 802C's. 1997 Bose
Tri Boost Kit Instructions
Tri Boost Kit Instructions Click here for older triboost version instructions(no 3-way LED) Parts Checklist...page 2-3 Schematic.....page 4 Populating and mounting the circuit board..page 5-14 Wiring Diagram.......page
EQ73 Parts list Reference Value Qty Description Marking Dim Manuf. YEL-VIO-BLK-GLD-BRN RED-RED-BRN-BRN RED-RED-BLK-BLK-BRN GRN-BLU-BRN-BRN
EQ73 Parts list (1) Reference Value Qty Description Marking Dim (2) Manuf. R52, R53 47R 2 Resistor 1%, 1/4W YEL-VIO-BLK-GLD-BRN R45, R46 180R 2 Resistor 5%, 1/2W R23, R24 220R 2 Resistor 1%, 1/4W RED-RED-BRN-BRN
Low Noise Amplifiers and Low Pass Filters with Automatic Selection with Frequency.
AAØZZ / WB9JPS IQPro LNA/LPF Low Noise Amplifiers and Low Pass Filters with Automatic Selection with Frequency By Craig Johnson, AAØZZ and Gary Johnson, WB9JPS aa0zz@cbjohn.com and GWJ@spamcop.net www.cbjohn.com/aa0zz
ASSEMBLY INSTRUCTIONS FOR NEW FK109 4 LED Railroad Crossing Flasher Kit WITH ADJUSTABLE FLASHING SPEED CONTROL with 4 Red 3mm Leds
ASSEMBLY INSTRUCTIONS FOR NEW FK109 4 LED Railroad Crossing Flasher Kit WITH ADJUSTABLE FLASHING SPEED CONTROL with 4 Red 3mm Leds Description: Very easy to build, The FK109 Led Flasher kit makes the perfect
mb808 FAB manual
mb808 FAB manual http://www.eight-oh-eight.org Step one: Power Supply: ATTENTION: You will be dealing with AC mains voltages in this part of the build, if you are not careful you can injure yourself, or
WIRING THE HEATER POWER SUPPLY
WIRING THE HEATER POWER SUPPLY Fig. 14 13/14 Take the longer PS board (with the 47R resistors and the fuse) and, using M3x6 screws, fix it to the chassis to the left of the mains transformer. The diodes
Service Manual - CD-303MP
R Service Manual - CD-303MP CD-303MP WiWi Industries Limited Engineering Department Bill of Materials 1 001-0000S-B90 P.C.B FILTER BOX 1 2 001-3900S-P90 P.C.B CD-3900 MAIM BOARD 1 3 002-01140-A00 I.C LA1140
2xVCX version 1.0. Calibration instructions can be found on the last page. Capacitor bypass MLCC X7R mm pin pitch
Produced by: Roll Your Own ljunggrenaudio.com Schematic & PCB Design by: KYMATICA DEVICES www.kymatica.com xvcx version.0 Bills Of Material Bold = PCB C C C3 C4 C5 C6 C7 C8 C9 C0 C C C3 C4 CON D D D3 D4
CAPI BB2521 Build Guide & BOM
This is a very simple build. I only have a few tips and things to look out for. I do recommend following these steps due to the diode/transistor relationship. 1. Install the three ceramic caps. If you
QRPGuys Digital RF Probe
QRPGuys Digital RF Probe First, familiarize yourself with the parts and check for all the components. If a part is missing, please contact us and we will send one. This kit contains seventeen 1206 size
22K (red red orange gold) 1pcs. 33K (orange orange orange gold) 5pc. 2.7 M (green violet red gold) 2pc.
TURNING FROG Long pliers, soldering, soldering iron stand with sponge, 2 AA batteries, one 9V battery, Tin, diagonal cutting pliers Turning Frog is a robot that uses a microphone as a detector. When microphone
Preliminary 2.4GHz FSK/GFSK Transceiver Revision History Rev. History Issue Date Remark 0.0 Initial issue November, 2008 Preliminary MD7105-A
Preliminary 2.4GHz FSK/GFSK Transceiver A7105 module specification MD7105-A08(-01) Important Notice: AMICCOM reserves the right to make changes to its products or to discontinue any integrated circuit
Collosalus 2015 FX Type: Flanger 3.25 W x 2.9 H
Collosalus 2015 FX Type: Flanger Based on the MXR 117 Download the previous version documentation here: http://www.madbeanpedals.com/projects/collosalus/collosalus.zip 3.25 W x 2.9 H B.O.M. Resistors Caps
ECO-6 & Installation Manual
ECO-6 & Installation Manual For the SPA4-RFR Upgrade Kit To upgrade SPA4 amplifiers v1.00 & v1.01 to v2.0 Some sections also apply to the PA1, PA2, and PA3 14 August 2015 2015 by Ralph Hartwell Spectrotek
D6, D7, D8, D9, D12, D13, D14, D15, D16, D17, D18, D19. Schottky rectifier diode. 1N5817-1N5819 or SB130
Roll Your Own ljunggrenaudio.com Altered States version 1.0 Bills Of Material Qty Value 12 1N4148 2 1N5818 4 1N750 4.7V 4 220p Device Diode Diode Zener diode Capacitor 30 100n 4 15p 8 560p 1 5x2 pin Capacitor
100W SUBWOOFER KIT. Total solder points: 383 Difficulty level: beginner advanced K8077 ILLUSTRATED ASSEMBLY MANUAL
100W SUBWOOFER KIT Powerful bass from a small cabinet thanks to the dual speaker principle Total solder points: 383 Difficulty level: beginner 1 2 3 4 5 advanced K8077 ILLUSTRATED ASSEMBLY MANUAL H8077IP-1
Elecraft Transverter Models XV50, XV144, XV222. Assembly Manual. Rev D, September 13, 2010 Copyright 2010, Elecraft; All Rights Reserved
Elecraft Transverter Models XV50, XV144, XV222 Assembly Manual Rev D, September 13, 2010 Copyright 2010, Elecraft; All Rights Reserved Table of Contents INTRODUCTION... 1 CUSTOMER SERVICE AND SUPPORT...
MAX3747/MAX3747A Evaluation Kit
19-3297; Rev A; 05/04 MAX3747/MAX3747A Evaluation Kit General Description The MAX3747/3747A evaluation kit (EV kit) simplifies evaluation of the MAX3747/3747A limiting amplifiers. The EV kit enables testing
CLASSIC PEDAL KIT. Assembly Instructions WHEN YOU CAN T BUY IT BUILD IT. StewMac Monarch RARE / VINTAGE / HARD TO GET
Sheet #i-2205 Updated 2/8 StewMac Monarch CLASSIC PEDAL KIT Kit case is unpainted IN COLLABORATION WITH EarthQuakerDevices Assembly Instructions The Monarch Overdrive is an all discrete, FET-based dirt
Remote Control Unit (SS-10/11/12/21) Service Manual. Remote Control Unit. SoundSpace 10/11/12/21
Service Manual Remote Control Unit SoundSpace 0//2/2 CONTENTS. REMOVAL PROCEDURES... 2 2. MECHANISM ASS'Y AND PARTS LIST... 3 3. MOUNTING DIAGRAMS AND PARTS LIST... 5 3.. Main P.C.B. Ass'y/Sensor P.C.B.
Schematic VCC J1 1 CON1 +5V D26 D25 D7 D8 D9 D10 D11 D12 D19 D20 D21 D22 D23 D24 D1 D2 D3 D4 D5 D6 D13 D14 D15 D16 D17 D18 R4 100R R2 100R R6 100R
Schematic +5V S D1 D2 D3 D4 D5 D6 D7 D8 D9 D10 D11 D12 D19 D20 D21 D22 D23 D24 D13 D14 D15 D16 D17 D18 D25 D26 R1 4K7 R2 100R Q1 9014-PNP C1 47uF R3 4K7 R4 100R Q2 9014-PNP C2 47uF R5 4K7 R6 100R Q3 9014-PNP
CTB-16K Hobbyist Line Kit 40 Amp 16 Channel Light Controller Assembly Manual *** Preliminary ***
CTB-16K Hobbyist Line Kit 40 Amp 16 Channel Light Controller Assembly Manual *** Preliminary *** Version 1.0 January 12, 2006 Copyright Light O Rama, Inc. 2006 Table of Contents 1 Introduction... 3 2 Required
HFpacker Amplifier Project Manual
HFpacker Amplifier Project Manual (Manual version: June 26, 2006) Virgil Stamps K5OOR and volunteers HFpacker-Amp 1 Introduction Welcome all builders to the homebrew Hfpacker-Amp Project. This project
~Dashboard Digital Voltmeter~
~Dashboard Digital Voltmeter~...November, 2002 This project is helpful to anyone who drives an automobile. I had found this project at the local libary... in an old publication. I made it and it worked
MonoWave(X) Construction Guide Version 1.2. June 30th, 2018
MonoWave(X) Construction Guide Version 1.2 June 30th, 2018 1 of 10 Construction Construction of the MonoWave (X) is relatively straightforward and generally only requires good general soldering skills.
Parts List DIY-81 rev 1. Capacitors. DIY-81 Project Parts list rev 1
Electrolytic C100 100 25 Axial 8 x 100uF/25V Axial C101 150 16 Axial 8 x 150uF/16V Axial C102 150 16 Axial 2 x 470uF/16V Radial C18 470 16 Radial C103 150 16 Axial C104 150 16 Axial C106 100 25 Axial C105
CCL LLC 88 Black Falcon Ave., Ste. 247, Boston, MA USA Contact: Antea Risso
88 Black Falcon Ave., Ste. 247, Boston, MA 02210 USA Contact: Antea Risso Digi-Key Corporation e-mail: antea@arduino.org 701 Brooks Ave.South PRODUCT CHANGE NOTIFICATION Thief River Falls, MN 5670 January
www MK-Electronic de EPSON LQ2170 Spares Guide Version 3 Page 1
REF PART NO DESCRIPTION REMARKS QTY 100 1025018 HOUSING ASSY., LOWER 1 101 1025039 COVER, FRONT 1 102 1025041 HOUSING, UPPER 1 103 1025027 COVER, PRINTER, REAR 1 104 1025024 COVER ASSY., PRINTER 1 105
VOX AC4tv Mercury Studio-Pro Upgrade Kit 21. Detail of the 15KΩ resistor in series with. as they appear in the Upgraded amp in location R23.
Detail of the 5KΩ resistor in series with the.kω resistor as they appear in the Upgraded amp in location R. Detail of the.7ηf in series with the 0KΩ carbon comp resistor as they appear in the Upgraded
MAX16929 Evaluation Kit Evaluates: MAX16929
19-5838; Rev 0; 4/11 MAX16929 Evaluation Kit General Description The MAX16929 evaluation kit (EV kit) is a fully assembled and tested surface-mount PCB that provides the voltages and features required
IV-3 VFD Shield for Arduino. Assembly Manual
June 2014 Table of Contents 1 Overview Features Applications 3 3 3 2 Assembly Hints 4 3 PCB Overview 5 4 Circuit Diagram 6 5 Assembly Diodes and IC socket Electrolytic capacitors Ceramic capacitors 10K
NXE1 Series Isolated 1W Single Output SM DC/DC Converters
NXE1 Series SELECTION GUIDE FEATURES Patents pending Lower Profile UL695 Recognition pending ANSI/AAMI ES661-1 Recognition pending 3kVDC Isolation Hi Pot Test Substrate Embedded Transformer Automated Manufacture
Ljunggren Audio Roll Your Own Optodist
Ljunggren Audio Roll Your Own Optodist Version: Optodist/VCA.0 Bill Of Material TYPE PART VALUE PCS NOTE Resistor R,R 0R Resistor R5,R0 K Resistor R3,R4 0K Resistor R,R9 68K Resistor R 00K Resistor R3
Build Instructions and User Guide
Build Instructions and User Guide Getting Started To build the Rock Drill 4069 you will need: Solder Wire Cutters Soldering Iron Small pliers The kit is suitable for beginners or more experienced builders
Assembly Instructions for the KA Electronics Flat MM Phono Preamplifier
Assembly Instructions for the KA Electronics Flat MM Phono Preamplifier Install IC sockets Flat MM Phono Preamp PC Board Stuffing Guide Place the PC Board on the bench silkscreen side face up. Drop six
White Light CLASSIC PEDAL KIT. Assembly Instructions WHEN YOU CAN T BUY IT BUILD IT. StewMac RARE / VINTAGE / HARD TO GET
Sheet #i-2206 Updated 5/18 StewMac White Light CLASSIC PEDAL KIT Kit case is unpainted IN COLLABORATION WITH EarthQuakerDevices Assembly Instructions The White Light Overdrive is based on vintage overdrives
RADIO CONTROLLED CAR KIT
RADIO CONTROLLED CAR KIT MODEL RCC-7K Instruction & Assembly Manual Elenco Electronics, Inc. Copyright 2005, 2001 by Elenco Electronics, Inc. All rights reserved. Revised 2005 REV-I 753288-I No part of
S AC-Coupled I/Os for Ease of Testing S Fully Assembled and Tested S +3.3V Power-Supply Operation S On-Board 25MHz Crystal
19-5065; Rev 0; 12/09 E V A L U A T I O N K I T A V A I L A B L E MAX3677 Evaluation Kit General Description The MAX3677 evaluation kit (EV kit) is an assembled demonstration board that provides convenient
SP6121 Demo Board Manual
SP6121 Demo Board Manual FEATURES DC/DC Synchronous Buck Converter for Distributed Power Systems. SIP design provides complete, ready to use solutions for : Vin=3.0-7.0V Vout=1.25-5.0V I out=8.0a (no air
www MK-Electronic de EPSON LQ670 Page 1 of 14
REF. PART NO. REMARKS QTY DESCRIPTION 100 1032438 1 HOUSING UPPER 101 1032439 1 COVER PRINTER 102 1034102 1 HOUSING ASSY. LOWER 103 1034610 1 LOGO PLATE 104 1034101 1 COVER ASSY. PRINTER; B 105 1034103
ROBOT SOUND REVERSING CAR KIT C-9802
ROBOT SOUND REVERSING CAR KIT TOOLS you'll need Alimentation 2 batteries 1,5 V AA (not included) You will find fun to learn electronics and mechanics assembling robot by reversing sound. This is a simple
V1.0 TBOH02 Self-Powered Active Load. 1 Introduction
1 Introduction The is a self-powered, precision active load. It is fully analog and does not contain any clocked circuitry. It was designed for EMC pre-compliance testing and for supply noise measurements
POWER SUPPLY MODEL XP-800. TWO AC VARIABLE VOLTAGES; 0-120V and 7A, PLUS UP TO 10A. Instruction Manual. Elenco Electronics, Inc.
POWER SUPPLY MODEL XP-800 TWO AC VARIABLE VOLTAGES; 0-120V and 0-40V @ 7A, PLUS 0-28VDC @ UP TO 10A Instruction Manual Elenco Electronics, Inc. Copyright 1991 Elenco Electronics, Inc. Revised 2002 REV-I
Name: S P CHINHARA ID: K-Bank
HYBRID SOLAR CHARGER CUM AUTOMATIC LIGHTING SYSTEM Date: 13.04.2018 Name: S P CHINHARA Email ID: spchinhara@rediffmail.com K-Bank NINL Internal Page 1 Confidentiality Statement The information in the document
GCE-780MPT. Service Manual - GCE-780MPT
GCE-780MPT Service Manual - GCE-780MPT 1 001-3896S-N50 P.C.B CD-3896 RDS MAIN 1 2 001-0000S-B90 P.C.B FILTER BOX 1 3 001-3896S-A60 P.C.B CD-3896 LAMP 1 4 001-3896S-B10 P.C.B CD-3896 SWITCH SW-A 1 5 001-3896S-B11
Maxim Integrated Products 1
19-4920; Rev 0; 8/09 MAX15046B Evaluation Kit General Description The MAX15046B evaluation kit (EV kit) is a fully assembled and tested circuit board that contains all the components necessary to evaluate
PART NO. DESCRIPTION VENDOR
QTY ITEM NO. PART NO. DESCRIPTION VENDOR CX 902 Replacement Parts QSC part # Description Qty. Notes or Component Reference Misc. CH-000122-00 COVER, PLC 1 CO-000111-00 CONN PLUG 3-PIN EURO GRN 2 CO-000176-00
PAT-4 TOROIDAL TRANSFORMER ASSEMBLY MANUAL
PAT-4 TOROIDAL TRANSFORMER ASSEMBLY MANUAL 2015 AkitikA, LLC All rights reserved Revision 1p3 August 22, 2015 Page 1 of 13 Table of Contents Table of Contents... 2 Table of Figures... 2 Section 1: About
UK-electronic 2012/15
UK-electronic 2012/15 Manual for the Kit Zentaurus Rev 1.21 with buffer or True bypass Page 1...Cover Page 2..3...Allocations, basics Page 4...5...Bill of material Page 6...7...Soldering the pcb Page 8...Building
MicroRint - ServiceManual
MicroRint - ServiceManual 046-22 Iss. 1.0 June 1998 Contents System Overview... 2 Figure 1... 2 Disassembling the MicroRint Computer for Circuit Investigation... 3 Reassembling the MicroRint Computer...4
C13, C19, C20, C21, C30. Maxim Integrated Products 1
9-456; Rev 0; 0/04 MAX58 Evaluation Kit General Description The MAX58 evaluation kit (EV kit) is a fully assembled and tested surface-mount circuit board that contains a step-up switching regulator, a
FX TYPE: DISTORTION Based on the Suhr Riot PCB artwork m2011 madbeanpedals Special thanks to culturejam! Release date: REVISED
http://www.madbeanpedals.com presents uproar FX TYPE: DISTORTION Based on the Suhr Riot PCB artwork m2011 madbeanpedals Special thanks to culturejam! Release date: 01.30.11 REVISED 02.08.11 This version
Bill Of Material MIXER AMIS - ZRM4
8 PCB Line S5701 S5702 S5703 AMIS - ZRM4 PCB (6336) SUB ASSLY. S5701 2020030503 HOS(T)/ALPHA - POT. 9mm,SEALED RD901-20-15K-B54/B50K BLK. NUT (RD 2111220101 RESISTOR M.O.R., 2W, 5%, 100 OHMS (#RSS) RoHS
EMG SpikerShield v1.2 Instructions
EMG SpikerShield v1.2 Instructions Prepare yourself. In 2-4 hours, you will have built your own Arduino compatible EMG SpikerBox, so you can control robots and anything you wish with your EMG muscle activity.
Electronic Dice Kit MitchElectronics 2019
Electronic Dice Kit MitchElectronics 2019 www.mitchelectronics.co.uk CONTENTS Schematic 3 How It Works 4 Materials 5 Construction 6 Important Information 7 Page 2 SCHEMATIC Page 3 SCHEMATIC EXPLANATION
INTRODUCTION TOOLS AND SUPPLIES Universal Kit-building Tools:
TABLE OF CONTENTS Introduction...2 Tools and Supplies...2 Before You Start Building...3 Soldering Tips:...3 Desoldering Tips:...4 Work Habits:...4 Sorting and Reading Resistors:...4 Reading Capacitors:...5
S Analog/PWM Input-Charge-Current Setting S Up to 1.2MHz Switching Frequency S Programmable Charge Current Up to 4A S Monitors Input/Outputs
19-4996; Rev 0; 10/09 General Description The MAX17015 evaluation kit (EV kit) is a complete, fully assembled and tested surface-mount PCB that features the MAX17015B highly integrated, multichemistry
Dynaco ST-70 & Mark 2/3 Quad-Cap / Power Supply Module Below Chassis Version
Page 1 CAE QUAD Cap Replacement Module PC-S7U-B & PC-S7U-B-M3 Rev3, 2-11 I. Introduction Thank you for choosing our ST-70 & Mark 2/3 Quad Electrolytic Capacitor & Power Supply Replacement Board. It is
FiveFish Studios PSU-2448Plus+ Assembly Guide
FiveFish Studios PSU-2448Plus+ Assembly Guide Copyright 2015-2017 FiveFish Audio Revision 1.02-20171105 No part of this document may be reproduced, either mechanically or electronically, posted online
Harbach Soft Key (sk-220) Installation Instructions for the Heathkit SB-220
Harbach Soft Key (sk-220) Installation Instructions for the Heathkit SB-220 Step-by-Step Instructions with Photos Based on an install by W4HDM Installation & Photos by W4HDM Instructions from http://www.harbachelectronics.com/
OD-KIT. Table of Contents. Precautions...2 Cautions Before Assembly...3 Tools to prepare...3 Checking the parts...3 Parts and materials...
2018 OD-KIT EJ 1 This kit is intended for those who have experience building electronic kits and who have a basic understanding of soldering and electronic parts. If you make a mistake during assembly,
SELECTION GUIDE. Nominal Input Order Code Voltage. Output Voltage. Reflected ripple current
www.murata-ps.com NML Series FEATURES RoHS compliant Single isolated output 1kVDC isolation Efficiency up to 85% Wide temperature performance at full 2 watt load, 40 C to 85 C Power density 2.01W/cm 3
IMPORTANT WARRANTY INFORMATION! PLEASE READ
IMPORTANT WARRANTY INFORMATION! PLEASE READ Return Policy on Kits When Not Purchased Directly From Vectronics: Before continuing any further with your VEC kit check with your Dealer about their return
Contents. DX Ignition Page 2
Contents 1.0 Intent 2.0 Specifications 3.0 Installation 4.0 Operation Precautions 5.0 Repair 6.0 Parts List 7.0 Glossary of Terms 8.0 Contact Information DX Ignition Page 2 1.0 Intent The purpose of this
Prototyping Walk through for PIC24HJ32GP202 Startup Schematic
Prototyping Walk through for PIC24HJ32GP202 Startup Schematic This prototyping walk through is meant to supplement the material in Experiment #6, the PIC24HJ32GP202 system startup. Figure 1 shows the pinout
NMA 5V, 12V & 15V Series Isolated 1W Dual Output DC/DC Converters
www.murata-ps.com NMA 5V, 12V & 15V Series FEATURES Efficiency up to 80% Wide temperature performance at full 1 Watt load, 40 C to 85 C Dual output from a single input rail Industry standard pinout Power
SHORT QUOTATION NOTICE TU/11-24/Pur/Qtn/ /3953-A dated:
SHORT QUOTATION NOTICE TU/11-24/Pur/Qtn/2016-17/3953-A dated:-30.12.2016 Sealed quotations are invited from reputed manufacturers/authorized dealers/vendors for supply, installation & commissioning etc.
SELECTION GUIDE. Nominal Input Voltage. Output Current. Output Voltage. Reflected ripple current
www.murata-ps.com SELECTION GUIDE Order Code Nominal Input Voltage Output Voltage Output Current Input Current at Rated Load Isolation Efficiency Capacitance MTTF1 V V ma % pf khrs Package Style FEATURES
PR-101 STEREO PREAMPLIFIER
PR-101 STEREO PREAMPLIFIER Headphone Amp ASSEMBLY MANUAL 2015, 2016 AkitikA LLC All rights reserved Revision 1p9 May 6, 2016 Page 1 of 21 Table of Contents Table of Contents... 2 Table of Figures... 3
CDI Revision Notes Term 1 ( ) Grade 12 General Unit 1 Materials & Unit 2 Fundamentals of Electronics
CDI Revision Notes Term 1 (2017 2018) Grade 12 General Unit 1 Materials & Unit 2 Fundamentals of Electronics STUDENT INSTRUCTIONS Student must attempt all questions. For this examination, you must have:
140P-2674 AND LATER 175P-4023 AND LATER 250P-2783 AND LATER
SERIAL NUMBERS 140P-2674 AND LATER 175P-4023 AND LATER 250P-2783 AND LATER FORM WC5310 3/95 (Rev. 9/97, 6/99, 1/00, 2/00) Systematics, Inc. 1025 Saunders Ln. West Chester, Pa. 19380 TABLE OF CONTENTS VIEW
NTA Series Isolated 1W Dual Output SM DC/DC Converters
www.murata-ps.com NTA Series FEATURES RoHS compliant Efficiency up to 78% Wide temperature performance at full 1 Watt load, 40 C to 85 C UL 94V-0 Package material Footprint over pins 1.64cm 2 Lead frame
SM361 RIG SWITCH CONSTRUCTION MANUAL
SM361 RIG SWITCH CONSTRUCTION MANUAL Document ver 1, For software release ver 1.1 May 27, 2016 Controls the power of 12V equipment while a vehicle is in use Product Development by: SM361 RIG SWITCH OVERVIEW
COINSHOOTER. Metal Detector. by William Lahr
COINSHOOTER Metal Detector by William Lahr Searching for coins and other lost articles along beaches and in parks can be both profitable and fun. The Coinshooter, a novel and inexpensive electronic metal
SELECTION GUIDE. Nominal Input Order Code Voltage. Output Voltage. Reflected ripple current
www.murata-ps.com FEATURES RoHS compliant Efficiency up to 82% Wide temperature performance at full 1 Watt load, 40 C to 85 C UL 94V-0 package material Reduced footprint at 0.98cm 2 Industry standard pinout
Gibson Goldtone SERVICE MANUAL NO. GG0005 ISSUE 1
Gibson Goldtone SERVICE MANUAL NO. GG0005 ISSUE 1 Date: December 21 st 2000 Product Code : G-04 Model No : Gibson Super Gold Tone 30RV Issued by: Trace Elliot Limited. Blackwater Trading Estate The Causeway,
RP40- _FR/ Package (4) CTRL Logic (3)
Features Regulated Converters Description Wide 4:1 Input Voltage Range 1.6kVDC Isolation for 24Vin and 48Vin, 3kVDC Isolation for 1Vin Efficiency up to 92% Six-Sided Continuous Shield UL695-1 AM2 Certified,
Evaluates: MAX MAX16935 Evaluation Kit. General Description. Features and Benefits. Quick Start. Table 1. EN Configuration (JU1)
General Description The MAX16935 evaluation kit (EV kit) demonstrates the MAX16935 high-voltage, current-mode step-down converter with low operating current. The EV kit operates over a wide 3.5V to 36V
PowerAmp Design. PowerAmp Design EVAL135 EVALUATION KIT FOR MODELS PAD135/ PAD183. Rev D
PowerAmp Design EVALUATION KIT FOR MODELS PAD35/ PAD83 EVAL35 Rev D INTRODUCTION The EVAL35 evaluation kit provides a convenient method to become familiar with the operation of the PAD35 or PAD83 Compact
BURGLAR ALARM KIT MODEL K-23. Assembly and Instruction Manual ELENCO
BURGLAR ALARM KIT MODEL K-23 Assembly and Instruction Manual ELENCO Copyright 2017, 1989 ELENCO Electronics, Inc. Revised 2017 REV-R- 753223 No part of this book shall be reproduced by any means; electronic,
Maxim Integrated Products 1
19-4002; Rev 2; 12/06 MAX6495 Evaluation Kit General Description The MAX6495 evaluation kit (EV kit) demonstrates a high-voltage overvoltage protection circuit for automotive applications that must survive
synthcube 291 VCF (buchla / verbos circuit realized by dustin stroh) module documents v2.0 06/20/2014 PCB rev 2.0 Errata:
synthcube 291 VCF (buchla / verbos circuit realized by dustin stroh) module documents v2.0 06/20/2014 PCB rev 2.0 Errata: copyright 2012 synthcube.com Page 1 Circuit Description A discussion thread about
PM-200 POWER SUPPLY MODULE v3.2 ASSEMBLY & INSTALLATION INSTRUCTIONS
PM-200 POWER SUPPLY MODULE v3.2 ASSEMBLY & INSTALLATION INSTRUCTIONS WARNING: Voltages inside the amplifier CAN & WILL KILL YOU! You MUST know how to work around HIGH VOLTAGE safely. If you do not, get
********SERVICE MANUAL********* MODELS:
********SERVICE MANUAL********* MODELS: -------------- 7553-70 Variable Speed Drive/Controller System, 600 rpm, 115v 7553-71 Variable Speed Controller only, 600 rpm,115v 7553-80 Variable Speed Drive/Controller
Tip: 2856 LED Lighting for the Airport Express Set Date:
Hi All, The 2856 Airport Express set was manufactured in 1983. On 09-11-1989 the locomotive was given a digital upgrade using a 6080 decoder. It has since had a digital upgrade to a high performance motor