Illustrated Parts Manual

Transcription

1 Illustrated Parts Manual 500 Series Snow Thrower 524/526/528/530 SWE CUB CADET LLC, P.O. BOX CLEVELAND, OHIO Printed In USA Form No (June 02, 2011)

2 To The Owner Thank You Thank you for purchasing a Cub Cadet Snow Thrower. It was carefully engineered to provide excellent performance when properly operated and maintained. All information in this manual is relative to the most recent product information available at the time of printing. Please be aware that this Illustrated Part s Manual may cover a range of product specifications for various models. Components listed and/or illustrated in this manual may not be applicable to all models. We reserve the right to change product specifications, designs and equipment without notice and without incurring obligation. Throughout this manual, all references to right (RH) and left (LH) are observed from the operating position. Table of Contents T Style Handle, Frame & Discharge Chute... 4 Chute Control... 6 Auger & Auger Housing... 8 Drive System...10 Engine Model 370-SUB Engine Model 478-SUA Engine Model 483-SUA Record Product Information To ease in ordering replacement parts, please locate the model plate on the equipment and record the information in the provided area to the right. You can locate the model plate by standing at the operator s position and looking down at the rear of the deck. Model Number Serial Number Painted Parts When ordering painted service parts, a four digit color suffix must be added to the part number (e.g. 783-XXXXX-0637). Please refer to the table below for current color codes: 0637 Black 4021 Yellow (Cub Cadet) 0499 Beige (Cub Cadet) 0685 Blue (Cub Cadet) 0691 Black Jack (Cub Cadet Commercial) 2

3 This page left intentionally blank. 3

4 T-Style Handle, Frame & Discharge Chute

5 T-Style Handle, Frame & Discharge Chute Hex Screw, 5/16-18 x A Handle Clutch Lock LH Assy B Handle Clutch Lock RH Assy Carriage Screw, 5/16-18 x A Handle Panel, includes Ref. 40 & B Handle Engagement Assembly LH B Handle Engagement Assembly RH Pivot Rod Screw, 8-16 x Screw, 1/4-20 x Screw, x Socket Screw, 1/4-20 x Flange Lock Nut, 1/ A Shoulder Nut, 1/ Click Pin,.092 x Handle Grip (524/526/528 SWE) Shift Knob Lamp Cable Tie D Lock Plate B Clutch Lock Cam Compression Spring C Clutch Lock Spring Torsion Spring A Rubber Bumper Flat Washer,.385 x.87 x Shoulder Screw,.374 x Shoulder Screw, 1/4-20 x A Speed Cable Selector C Panel Bracket A Shift Lever Wing Knob A Lower Handle A Upper Handle RH A Upper Handle LH E-Ring Cable Tie Clutch Trigger Pin, 3/ Light Socket Lens X41804 Lens Label Screw, TT, 1/4-20 x.500 (For ground wire) AB Screw, #10-16 x.625 (530 SWE) Heated Grip Switch (530 SWE) Heated Grip (530 SWE) Harness (Inc # 39) 524/526/528 SWE Harness (530 SWE) Not Shown 5

6 6 Chute Control

7 Chute Control A Chute Support Bracket (524 SWE) A Chute Support Bracket (526 SWE, 528 SWE, 530 SWE) Handle Assembly Bolt, Carriage, 5/16-18 x Bolt, Carrier, 5/16-18 x Screw, HL, 1/4-15 x Hex Head Screw, 1/4-20 x Hex Head Screw, 5/16-24 x Screw, HL, 1/4-15 x A Clevis Pin, 3/8 x Nut, Flangelock, 5/ Nut, Flangelock, 1/ Wing Nut, 1/ Internal Cotter Pin Bow-Tie Cotter Pin Wing Knob, 5/ A Chute, Upper A Chute, Lower Cable Guide, Chute Tilt Washer, Flat,.349 x Washer, Flat,.25 x Screw, Shoulder,.312 x 3.5 x 1/ Chute Rod, 3/8 Hex Cable Bracket A Gearbox Assembly, Chute Rotation A Chute Control, 4-Way Screw, #8 x Screw, 8-32 x A Joystick Plug Joystick Trigger A Screw, x Hex Shaft Hexlock Nut, 1/ Gear, 14 T Worm Gear Cover Pawl Lock C Torsion Spring,.721 ID x Washer, Flat,.625 x 1.0 x Screw, Shoulder,.340 x.950 x 1/ Hex Bearing Flange Bearing B Cable Lock B Gear Bracket A 4-Way Cable Way Cable w/clip A Shift Assembly Gear Set Assembly Handle Housing Assembly Screw, #8-18 x Pin, Roll Block, Asm Joint Pin, Roll Not Shown 7

8 Auger & Auger Housing

9 Auger & Auger Housing A Extension Cord A Impeller Assembly Hex Bolt, 3/8-16 x Screw, 5/16-18 x Carriage Bolt, 5/16-18 x.750 (24, 26 ) Crg. Bolt, 5/16-18 x.750 (28, 30 ) A Auger Clutch Cable Flange Lock Nut, 5/16-18 (24, 26 ) Hex Nut, 5/16-18 (28, 30 ) Flange Lock Nut, 3/ Flange Bearing,.50 x.75 x Bow Tie Cotter Pin Cable Tie Push-On Nut,.25 Dia Extension Spring,.38 OD x Wave Washer,.625 x.885 x Bell Washer,.340 x.872 x Bell Washer,.340 x.872 x Stainless Steel, Shave Plate, Stainless Steel, Shave Plate, 28" Stainless Steel, Shave Plate, 26" Stainless Steel, Shave Plate, 24" Shoulder Screw, 3/8-16 x.496 x Shoulder Screw, 3/8-16 x.625 x A Shear Pin Hex Flange Bearing Flange Ball Bearing,.75 x Flat Idler Pulley Bearing Housing A Auger Idler Bracket A Gearbox Assembly, Auger, A Gearbox Assembly, Auger, B Gearbox Assembly, Auger, B Gearbox Assembly, Auger, Spiral Assembly - LH Spiral Assembly - RH Spacer, 1.25 x.75 x Auger Housing, Auger Housing, Auger Housing, Auger Housing, Flat Washer,.76 x 1.49 x Drive Lube Fitting A Flange Bushing,.800 x A Bearing Housing Spacer, Carriage, 5/16-18 x Deluxe Slide Shoe Washer, Flat,.349 x.879 x Carriage Screw, 1/4-20 x Flange Lock Nut, 1/ Chute Adapter Clean-out Tool Mtg. Bracket Clean-Out Tool A Housing Assembly - RH A Housing Assembly - LH Screw, 1/4-20 x Axle, Auger, Axle, Auger, Axle, Auger, Axle, Auger, Hi-Pro Key Dowel Pin,.25OD x Worm Shaft A Worm Gear, 20T, 28", Worm Gear, 20T, 24", Thrust Collar Plug, 1/4 x Oil Seal,.75 x x Flat Washer,.76 x Flat Washer,.51 x 1.12 x Flange Bearing,.75 x 1.00 x Flange Lock Nut Spacer, 1.25 OD x.75 ID x 3/16 Lg Not Shown 9

10 10 Drive System

11 Drive System Dogg Assembly, RH Dogg Assembly, LH A Drive Shaft Assembly Friction Wheel Disc Assembly B Friction Wheel Support Bracket A Rod Shift Assembly Hex Head Screw, 5/16-24 x Screw, 1/4-20 x Screw, 1/4-20 x B Actuator Shaft Nut, Flangelock, 3/ Hi-Pro Key, 3/16 x 3/4 DIA E-Ring Retainer Ring Gear, 56T Nut, Speed, Spacer,.76 x Extension Spring,.380 x Extension Spring,.500 x Washer, Flat,.76 x Washer, Bell,.340 x Washer, Flat,.58 x Idler Pulley Assembly Hex Head Screw, 3/8-24 x A Taptite Sems Screw, 3/8-16 x A Screw, Shoulder,.368 x.113 x 1/ A Screw, Shoulder,.340 x.335 x 1/ Hex Flange Bearing,.75 ID Ball Bearing,.5625 x x B Drive Clutch Cable Washer, Flat,.38 x B Steering Cable Spacer,.508 x Axle Support Tube Spacer, Axle Cable Roller Auger Cable Guide Bracket B Wheel Drive Frame Shaft Retainer, LH Shaft Retainer, RH A Auger Clutch Cable Guide Bracket B Drive Clutch Cable Guide Bracket Frame Cover A Nut, Flange, 5/ Hex Head Screw, 5/16-24 x Auger Pulley, 8.1 x Pulley, Half, Taptite Screw, 1/4-20 x Shoulder Screw,.500 x Nut, Push-On,.25 Dia Belt Cover, (526/528/530 SWE) Belt Cover (524 SWE) A Spring, Torsion,.850 x Plug, 3/8 ID Plug, 1/2 ID Washer, Lock, 5/ Washer, Flat,.406 x Washer, Lock, 1/ Washer, Flat,.34 x B Hex Head Screw, 5/16-24 x A Pulley Adapter,.75 DIA B Spacer, Shoulder,.3175 x Spacer,.875 x A Spacer,.340 x Spacer, Shoulder,.260 x Belt,.500 x 37 (526/528/530 SWE) Belt,.500 x (524 SWE) A Belt, 3/8 x (526/528/530 SWE) V Belt, 3/8 x 34.4 (524 SWE) Pulley, Half, 3/8 x C Drive Idler Bracket Cover Plate (526/528/530 SWE) A Cover Plate (524 SWE) Wheel, LH (528 SWE, 530 SWE) Wheel, RH (528 SWE, 530 SWE) A-0931 Wheel, LH (524 SWE, 526 SWE) A-0931 Wheel, RH (524 SWE, 526 SWE) Spacer, 1.25 x.75 x Axle,.75 x Hex Head Screw, 1/4-20 x

12 Drive System Nut, Flange Lock, 5/ Nut, Flange Lock, 1/ A Spring, Torsion,.750 x Washer, Flat,.469 x.875 x Friction Wheel Assembly A Speed Selector Pivot Bracket A Speed Selector Shift Bracket Hex Head Screw, 1.25 x Cable Guide (524 SWE) Cable Guide (526/528/530 SWE) Washer, Flat,.330 x A Bearing Assembly, Friction Wheel Screw, 1/4-14 x Friction Wheel, 5.5 OD Friction Wheel Plate A Friction Pin, Disc Bearing Ball Bearing, 30 x 55 x 13 12

13 13

14 370-SUB-11 Muffler Muffler Assembly Muffler Stud M Muffler Stud Assembly Exhaust Pipe Gasket Nut,M Exhaust Pipe Shield Bolt M Bolt M A Muffler Shield 777I22990 Label-Run/Choke 777I22991 Label-Primer 777I22992 Label-Electric Start 777I23026 Label-Electric Start Warning 777S33610 Label- Oil / Warning 14

15 370-SUB-11 Carburetor Stud M Stud M Carburetor Insulator Gasket Carburetor Insulator A Carburetor Gasket A Primer Assembly Primer Bulb A Carburetor Assembly Carburetor Gasket Plate Choke Control a Choke Shaft b Choke Plate c Throttle Shaft d Throttle Plate e Screw M3 5 f Lock Washer g Gasket, Throttle Plate h Idle Jet Assembly i Idle Speed Adjusting Screw j Mixture Screw k Primer Hose l Hose Clamp m Carburetor Body n Float Pin o Emulsion Tube p Needle Valve q Main Jet r Needle Valve Spring s Float t Fuel Bowl Gasket u Fuel Bowl v Fuel Bowl Gasket w Fuel Bowl Mounting Bolt x Fuel Drain Plug Gasket y Fuel Drain Plug A Carburetor Kit - Major (Incl.g,h,I,n,o,p,q,r,s,t,v,x) 15

16 SUB-11 Crankcase

17 370-SUB-11 Crankcase Air Cleaner Housing Nut Choke Knob Throttle Control Knob Key Switch Base Key Choke Push Rod Heater Box Bolt M Piston Ring Set Piston Pin Snap Ring Piston Piston Pin Bolt M Air Shield Connecting Rod Assembly Governor Arm Shaft Washer Governor Seal Cotter Pin Camshaft Assy Radial Ball Bearing, Woodruff Key A Crankshaft Assembly Governor Gear/Shaft Assembly Dowel Pin Dowel Pin Crankcase Cover Gasket Cover Comp,Left Crankcase Bolt M Oil Fill Plug Asm O-Ring Oil Seal, A Short Block (Incl.4,21,29,30,46,48,49, 52-55,58-72,74-81) Oil Drain Pipe Assy Washer Oil Drain Plug Oil Seal Oil Drain Assembly 952Z370-SUB-11 Complete Engine 777I22990 Label-Run/Choke 777I22991 Label-Primer 777I22992 Label-Electric Start 777I23026 Label-Electric Start Warning 777S33610 Label- Oil / Warning Crankcase Cover Kit (Incl.64,70-73,76) A Crankshaft Kit (Incl.64-66,76,81) Crankcase Kit (Incl.61,64,76,77,81) A Gasket Kit - Complete (Incl.4,21,29-31,34,46, 60,61,70,76,79,81) 17

18 370-SUB-11 Starter Assembly & Blower Housing Ignition Coil Assembly Air Flow Shield Bolt M Bolt M Coil Assy.,Charge Flywheel Fan,Cooling Pulley,Starter Nut,Special,M Bolt M Recoil Starter Handle A Blower Housing Gasket Bolt M Recoil Starter Bolt M Switch Housing Mounting Bracket Nut,M Bolt M Bolt M Bolt M Dowel Pin A Startup Electromotor Bolt M Blower Housing Shield Flexible Clamp 18

19 370-SUB-11 Fuel Tank & Mounting Primer Bracket Bolt M Governor System Shield Governor Spring Throttle Linkage Spring Throttle Linkage Governor Arm Nut M Governor Arm Bolt Fuel Hose Clamp Fuel Hose Bolt M Dipstick Decoration Cover Bolt Bolt M Oil Fill Tube O-Ring Oil Fill Tube Oil Fill Tube O-Ring Dipstick Assembly A Fuel Cap Assembly Fuel Level Indicator B Fuel Tank Assembly 777I22990 Label-Run/Choke 777I22991 Label-Primer 777I22992 Label-Electric Start 777I23026 Label-Electric Start Warning 777S33610 Label- Oil / Warning 19

20 370-SUB-11 Cylinder Head a

21 370-SUB-11 Cylinder Head Bolt M Valve Cover Breather Hose 3a Breather Hose Clamp Valve Cover Gasket Retainer,In.Valve Spring Rocker Arm Assembly Nut,Pivot Locking Adjusting Nut,Valve Rocker Arm Bolt,Pivot Adjuster,Exh Valve Retainer,Ex.Valve Spring Valve Spring Intake Valve Seal Bolt M Push Rod Guide A Cylinder Head Assembly (Incl.4,5,7-14,16,17,21, 29,30,46,50,51) Spark Plug/F6Rtc Gasket,Cylinder Head Push Rod Tappet Dowel Pin A Exhaust Valve A Intake Valve A Valve Cover Kit 952Z370-SUB-11 Complete Engine B Gasket Kit - External (Incl.4,21,29-31,34,79) A Gasket Kit - Complete (Incl.4,21,29-31,34,46, 60,61,70,76,79,81) 21

22 478-SUA Muffler & Controls Bolt M Muffler Shield Bolt M Throttle Control Knob Control Panel Key Switch Base Key Choke Knob Bolt M Muffler Baffle Heat Shield Bolt M Muffler Assembly Nut M8 22

23 478-SUA Carburetor Stud M Carburetor Insulator Gasket Carburetor Insulator Carburetor Gasket A Carburetor Assembly A Primer Assembly Primer Bulb Heater Box Choke Control Lock Washer Nut M6 a n/a Choke Shaft b n/a Lock Washer c n/a Screw M3 5 d n/a Choke Plate e n/a Throttle Shaft f n/a Throttle Plate g n/a Lock Plate h n/a Idle Jet Assembly i n/a Idle Speed Adjusting Screw j n/a Mixture Screw k Primer Hose l Hose Clamp m n/a Carburetor Body n n/a Float Pin o n/a Emulsion Tube p n/a Needle Valve q n/a Main Jet r n/a Needle Valve Spring s n/a Float t Fuel Bowl Gasket u n/a Fuel Bowl v Fuel Bowl Gasket w Fuel Bowl Mounting Bolt x Fuel Drain Plug Gasket y Fuel Drain Plug Carburetor Kit - Major (Incl.g,n,o,p,q,r,s,t,v,x) 23

24 478-SUA Crankcase

25 5P65M0B Crankcase Connecting Rod Assembly Piston Piston Pin Snap Ring Piston Pin Piston Ring Set Governor Gear/Shaft Assembly Radial Ball Bearing Washer Cotter Pin Governor Seal Governor Arm Shaft Crankshaft Assembly Woodruff Key Dowel Pin Dowel Pin Camshaft Assy Crankcase Cover Gasket Washer 16x O-Ring Oil Filler Plug Assembly Cover Comp,Left Crankcase Oil Seal 30? Bolt M Bolt M Bolt M Bolt M Dipstick Clamp Bolt M Oil Fill Tube O-Ring Oil Fill Tube Assembly Dipstick O-Ring A Dipstick Assembly Crankcase Kit (Incl.50,53,77,81) Oil Drain Pipe Assy Washer Oil Drain Plug Oil Seal 30x Oil Drain Assembly 952Z478-SUA Complete Engine Crankcase Cover Kit (Incl.50,60,61,64-67) Crankshaft Kit (Incl.50,55,56,65,81) Gasket Kit - External (Incl.79,108,123, ) Gasket Kit - Complete (Incl.53,60,65,79,81,106, 108,123, ) Short Block Assembly (Incl.41-45,49-68,77-81,102, 105,106,108,110,123,129,130) 25

26 478-SUA Fuel Tank & Mounting Fuel Cap Assembly Viton / Vented Fuel Level Indicator Bolt M Bush, Gas Tank Bush,Gas Tank Fuel Tank Assembly Fuel Tank Shroud Fuel Tank Mounting Bracket Engine Shroud Bolt M Bush Fue Line Kit Fuel Hose Clamp Bolt M Fuel Tank Mounting Bracket Nut M Nut M Governor Arm Bolt Governor Arm Governor Spring Throttle Linkage Spring Throttle Linkage Primer Bracket Bolt M6 14 N/S Fuel Tank Nipple / Filter 26

27 478-SUA Starting System & Blower Housing Bolt M Startup Electromotor Bolt M Ignition Coil Assembly Ignition Coil Bolt Coil Assy.Charge Bolt M Bolt M Alternator Wire Clamp Brkt Flywheel Fan,Cooling Pulley,Starter Nut,Special M Bolt M Bolt M Blower Housing Recoil Starter Gasket Bolt M

28 478-SUA Cylinder Head a

29 478-SUA Cylinder Head Valve Kit Valve Kit Tappet Push Rod Kit Cylinder Head Kit (Incl.106,110,111,123) Dowel Pin Gasket,Cylinder Head Spark Plug/F6Rtc Exhaust Pipe Gasket Stud M Muffler Stud Assembly Bolt M Intake Valve Seal Valve Spring Retainer Valve Spring Retainer,Ex.Valve Spring Adjuster,Exh Valve Push Rod Guide Rocker Arm Assembly Bolt,Pivot Rocker Arm Adjusting Nut,Valve Nut,Pivot Locking Valve Cover Bolt Valve Cover Gasket Valve Cover Breather Hose 125a Clamp, Breather Hose Cylinder Baffle Bolt M Valve Cover Kit 952Z478-SU Complete Engine Gasket Kit - External (Incl.79,108,123, ) Gasket Kit - Complete (Incl.53,60,65,79,81,106, 108,123, ) Cylinder Head Ass'y (Incl.100,101,104,106, , ,123, ) 29

30 RUN STOP For Household and Commercial Use. FOR ELECTRIC STARTER ASSEMBLY ONLY For 420 C.C. Engines Maximum. 120v., 60Hz., A.C. 13.2Amp, Output Wattage: 700W, Rated Load Speed: 4300 R.P.M. INTERMITTENT DUTY ONLY. Do not crank for longer than 8 seconds without allowing to cool for 10 minutes. Use only SJTW/SJTW-A 3 wire grounded cordset suitable for outdoor use and oil resistant. SEE OWNERS MANUAL. DO NOT USE IN RAIN. Class B Insulation. Assembled in China. Thermally-Protected. POUR LE DÉMARREUR ÉLECTRIQUE SEULEMENT Pour des moteurs de 420 C.C. maximum. 120V., 60Hz., 13.2A, Puissance de sortie: 700W, Vitesse à charge nominale: 4300 tr/min. SERVICE INTERMITTENTSEULEMENT. N'enfoncez pas le bouton du démarreur pour faire tourner le moteur pendant plus que 8 secondes sans laisser le démarreur refroidir pendant 10 minutes.n utilisez qu une rallonge à trois fils avec mise à la terre qui est conçue pour être utilisée à l extérieur et résistant à l huile, types SJTW/SJTW-A. CONSULTEZ LE MANUEL D'UTILISATION. N EMPLOYEZ PAS SOUS LA PLUIE. Isolation de classe B. Assemblé en Chine. Isolation thermique. Chongqing Vision Industry Co.,Ltd JQ-190 Chongqing Vision Industry Co.,Ltd Pour utilisations résidentielle et commerciale. JQ-190 For Household and Commercial Use. Label can be printed with either Company Name & Number FOR ELECTRIC STARTER ASSEMBLY ONLY For 420 C.C. Engines Maximum. 120v., 60Hz., A.C. 13.2Amp, Output Wattage: 700W, Rated Load Speed: 4300 R.P.M. INTERMITTENT DUTY ONLY. Do not crank for longer than 8 seconds without allowing to cool for 10 minutes. Use only SJTW/SJTW-A 3 wire grounded cordset suitable for outdoor use and oil resistant. SEE OWNERS MANUAL. DO NOT USE IN RAIN. Class B Insulation. Assembled in China. Thermally-Protected. POUR LE DÉMARREUR ÉLECTRIQUE SEULEMENT Pour des moteurs de 420 C.C. maximum. 120V., 60Hz., 13.2A, Puissance de sortie: 700W, Vitesse à charge nominale: 4300 tr/min. SERVICE INTERMITTENTSEULEMENT. N'enfoncez pas le bouton du démarreur pour faire tourner le moteur pendant plus que 8 secondes sans laisser le démarreur refroidir pendant 10 minutes.n utilisez qu une rallonge à trois fils avec mise à la terre qui est conçue pour être utilisée à l extérieur et résistant à l huile, types SJTW/SJTW-A. CONSULTEZ LE MANUEL D'UTILISATION. N EMPLOYEZ PAS SOUS LA PLUIE. Isolation de classe B. Assemblé en Chine. Isolation thermique. Chongqing Jili Yunfeng Industry(Group) Co.,Ltd ACQD190 Chongqing Jili Yunfeng Industry(Group) Co.,Ltd Pour utilisations résidentielle et commerciale. ACQD SUA Label Map 777I23018 PRIMER AMORCEUR 777S I23442 IGNITION ALLUMAGE 777I23027 WARNING - Risk of electric shock. Connect to a properly grounded outlet only. Risk of electric shock. Keep extension cord connection dry and off the ground. Do not expose to rain, store indoors. AVERTISSEMENT-Risque de secousse électrique. N'utiliser qu'une prise de courant correctement mise à la terre. Risque de secousse électrique. La rallonge électrique doit rester sèche et ne pas toucher le sol. La protéger des intempéries et la remiser à l'intérieur. WARNING - Risk of electric shock. Connect to a properly grounded outlet only. Risk of electric shock. Keep extension cord connection dry and off the ground. Do not expose to rain, store indoors. AVERTISSEMENT-Risque de secousse électrique. N'utiliser qu'une prise de courant correctement mise à la terre. Risque de secousse électrique. La rallonge électrique doit rester sèche et ne pas toucher le sol. La protéger des intempéries et la remiser à l'intérieur. STOP 777I23017 RUN MARCHE 777I22992 CHOKE VOLET DE DÉPART Push to start - Do not run starter more than 10 times at intervals of 5 Seconds On / 5 seconds Off. If engine does not start, consult operators manual. Appuyez pour démarrer - Ne pas utiliser le démarreur plus de 10 fois en appuyant pendant 5 secondes et en relâchant pendant 5 secondes. Si le moteur ne démarre pas, consultez la notice d'utilisation. SERIAL NUMBER BAR CODE LABEL SN: XXxxxx/xxxxxxxxxxxx Lot No. xxxxxxxxxxxx EPA LABEL 30

31 31

32 483-SUA Muffler & Controls Bolt,M Muffler Shield Bolt M Throttle Control Knob Control Panel Key Switch Base Key Choke Knob Bolt M Exhaust Pipe Shield Carb Isolator Bracket Bolt M Muffler Assembly Nut M8 32

33 483-SUA Carburetor f g i e c h a b c d m j k l x y n o p q r s t u v w Stud M Carburetor Stud M Carburetor Carburetor Insulator Gasket Carburetor Insulator Carburetor Gasket A Carburetor Assembly A Primer Assembly Primer Heater Box Choke Control Lock Washer Nut M6 a n/a Choke Shaft b n/a Lock Washer c n/a Screw M3 5 d n/a Choke Plate e n/a Throttle Shaft f n/a Throttle Plate g n/a Lock Plate h n/a Idle Jet Assembly i n/a Idle Speed Adjusting Screw j n/a Mixture Screw k Primer Hose l Hose Clamp m n/a Carburetor Body n n/a Float Pin o n/a Emulsion Tube p n/a Needle Valve q n/a Main Jet r n/a Needle Valve Spring s n/a Float t Fuel Bowl Gasket u n/a Fuel Bowl v Fuel Bowl Gasket w Fuel Bowl Mounting Bolt x Fuel Drain Plug Gasket y Fuel Drain Plug A Carburetor Kit - Major (Incl.g,h,n,o,p,q,r,w,t,v,x) 33

34 483-SUA Crankcase

35 483-SUA Crankcase Connecting Rod Assembly Piston Piston Pin Snap Ring Piston Pin Piston Ring Set Governor Gear/Shaft Assembly Radial Ball Bearing 6202-P Washer Cotter Pin Governor Seal Governor Arm Shaft Crankshaft Kit (Incl.50,55,56,65,81) Woodruff Key Dowel Pin Dowel Pin Camshaft Assy Crankcase Cover Gasket Washer O-Ring Oil Filler Plug Assembly Crankcase Cover Kit (Incl.50,60,61,64-68) Oil Seal Bolt M Bolt M Bolt M Bolt M Dipstick Clamp Bolt M Oil Fill Tube O-Ring Oil Fill Tube Assembly Dipstick O-Ring A Dipstick Assembly A Crankcase Kit (Incl.50,53,77,81) Oil Drain Pipe Assy Washer Oil Drain Plug Oil Seal Balanceable Shaft Assy Bearing 6207-P Oil Drain Assembly 952Z483-SUA Complete Engine Gasket Kit - External (Incl.79,108,125, ) A Gasket Kit - Complete (Incl.53,60,65,79,81,106, 108,125, ) B Short Block Assembly (Incl.41-45,49-61,63-68,77-79, 81,102,105,106,108,110,125, 131,132,142,143) 35

36 483-SUA Fuel Tank & Mounting Fuel Cap Assembly Fuel Level Indicator Bolt M Bush Gas Tank Bush Gas Tank Fuel Tank Assembly Left Trim Plate Rear Mainting Bracket Assy Right Trim Plate Bolt M Bush Fuel Hose Kit Fuel Hose Clamp Bolt M Gas Tank Support Bracket Nut M Nut M Governor Arm Bolt Governor Arm Governor Spring Throttle Linkage Spring Throttle Linkage Primer Bracket Bolt M6 14 N/S Fuel Tank Nipple 36

37 483-SUA Starter Assembly & Blower Housing Bolt M Startup Electromotor Bolt M Ignition Coil Assembly Ignition Coil Bolt Coil Assy.Charge Bolt M Bolt M Alt Wire Clamp Brkt Flywheel Fan Cooling Pulley Starter Nut Special M Bolt M Bolt M Blower Housing Recoil Starter Gasket Bolt M Starter Handle 37

38 SUA Cylinder Head a

39 483-SUA Cylinder Head Valve Kit Valve Kit Tappet Push Rod Cylinder Head Kit (Incl.106, ,125) Dowel Pin Gasket Cylinder Head Spark Plug/F6Rtc Exhaust Pipe Gasket Stud M Muffler Stud Assembly Bolt M Bolt M Intake Valve Seal Valve Spring Retainer Valve Spring Retainer Ex.Valve Spring Adjuster Exh Valve Push Rod Guide Rocker Arm Assembly Bolt Pivot Rocker Arm Adjusting Nut,Valve Nut Pivot Locking Valve Cover Bolt Valve Cover Gasket Valve Cover Breather Hose 126a Breather Hose Clamp Air Shield Bolt M Valve Cover Kit 952Z483-SUA Complete Engine Gasket Kit - External (Incl.79,108,125, ) A Gasket Kit - Complete (Incl.53,60,65,79,81,106, 108,125, ) B Cylinder Head Assembly (Incl.100,101,104,106, , 112, , ,125, 129, ) 39

40 RUN STOP For Household and Commercial Use. FOR ELECTRIC STARTER ASSEMBLY ONLY RAIN. Class B Insulation. Assembled in China. Thermally-Protected. POUR LE DÉMARREUR ÉLECTRIQUE SEULEMENT Isolation de classe B. Assemblé en Chine. Isolation thermique. Pour utilisations résidentielle et commerciale. For Household and Commercial Use. FOR ELECTRIC STARTER ASSEMBLY ONLY RAIN. Class B Insulation. Assembled in China. Thermally-Protected. POUR LE DÉMARREUR ÉLECTRIQUE SEULEMENT Isolation de classe B. Assemblé en Chine. Isolation thermique. Pour utilisations résidentielle et commerciale. 483-SUA Label Map 777S I23018 PRIMER AMORCEUR 777I23039 IGNITION ALLUMAGE 777I23027 WARNING - Risk of electric shock. Connect to a properly grounded outlet only. Risk of electric shock. Keep extension cord connection dry and off the ground. Do not expose to rain, store indoors. AVERTISSEMENT-Risque de secousse électrique. N'utiliser qu'une prise de courant correctement mise à la terre. Risque de secousse électrique. La rallonge électrique doit rester sèche et ne pas toucher le sol. La protéger des intempéries et la remiser à l'intérieur. WARNING - Risk of electric shock. Connect to a properly grounded outlet only. Risk of electric shock. Keep extension cord connection dry and off the ground. Do not expose to rain, store indoors. AVERTISSEMENT-Risque de secousse électrique. N'utiliser qu'une prise de courant correctement mise à la terre. Risque de secousse électrique. La rallonge électrique doit rester sèche et ne pas toucher le sol. La protéger des intempéries et la remiser à l'intérieur. STOP For 420 C.C. Engines Maximum. 120v., 60Hz., A.C. 13.2Amp, Output Wattage: 700W, Rated Load Speed: 4300 R.P.M. INTERMITTENT DUTY ONLY. Do not crank for longer than 8 seconds without allowing to cool for 10 minutes. Use only SJTW/SJTW-A 3 wire grounded cordset suitable for outdoor use and oil resistant. SEE OWNERS MANUAL. DO NOT USE IN Pour des moteurs de 420 C.C. maximum. 120V., 60Hz., 13.2A, Puissance de sortie: 700W, Vitesse à charge nominale: 4300 tr/min. SERVICE INTERMITTENTSEULEMENT. N'enfoncez pas le bouton du démarreur pour faire tourner le moteur pendant plus que 8 secondes sans laisser le démarreur refroidir pendant 10 minutes.n utilisez qu une rallonge à trois fils avec mise à la terre qui est conçue pour être utilisée à l extérieur et résistant à l huile, types SJTW/SJTW-A. CONSULTEZ LE MANUEL D'UTILISATION. N EMPLOYEZ PAS SOUS LA PLUIE. Chongqing Vision Industry Co.,Ltd JQ-190 For 420 C.C. Engines Maximum. 120v., 60Hz., A.C. 13.2Amp, Output Wattage: 700W, Rated Load Speed: 4300 R.P.M. INTERMITTENT DUTY ONLY. Do not crank for longer than 8 seconds without allowing to cool for 10 minutes. Use only SJTW/SJTW-A 3 wire grounded cordset suitable for outdoor use and oil resistant. SEE OWNERS MANUAL. DO NOT USE IN Pour des moteurs de 420 C.C. maximum. 120V., 60Hz., 13.2A, Puissance de sortie: 700W, Vitesse à charge nominale: 4300 tr/min. SERVICE INTERMITTENTSEULEMENT. N'enfoncez pas le bouton du démarreur pour faire tourner le moteur pendant plus que 8 secondes sans laisser le démarreur refroidir pendant 10 minutes.n utilisez qu une rallonge à trois fils avec mise à la terre qui est conçue pour être utilisée à l extérieur et résistant à l huile, types SJTW/SJTW-A. CONSULTEZ LE MANUEL D'UTILISATION. N EMPLOYEZ PAS SOUS LA PLUIE. Chongqing Jili Yunfeng Industry(Group) Co.,Ltd ACQD190 Chongqing Vision Industry Co.,Ltd JQ-190 Chongqing Jili Yunfeng Industry(Group) Co.,Ltd ACQD I23017 Label can be printed with either Company Name & Number 777I22992 SERIAL NUMBER BAR CODE LABEL SN: XXxxxx/xxxxxxxxxxxx Lot No. xxxxxxxxxxxx EPA LABEL 40

41 Notes 41

42 42

43 43

44 G E N U I N E FAC TORY PARTS To order replacement parts, call a Customer Support Representative at (800) 965-4CUB. Locate your nearest Cub Cadet dealer at (877) or visit to find the nearest Cub Cadet dealer in your area. CUB CADET LLC, P.O. BOX CLEVELAND, OHIO