Kalamazoo Packaging Systems

Transcription

1 Kalamazoo Packaging Systems Division of Kal-Tek, Inc. MODEL# 939-M Volt WINDOW/PANEL STRETCH WRAP SYSTEM OPERATOR S MANUAL 1

2 Table of Contents Introduction...3 Warranty 3 Wrapping Operation 4 Description of wrap cycle 5 Controls..5-6 AC Solid State Drive Settings.6-9 Maintenance..10 Lubrication...11 Chain Tensions...11 Trouble Shooting...12 Machine Layout..13 Tower Assemble Turntable Assemble Top Platen Assemble Subpanel Assemble Control Console Assemble Variable Tension Film Delivery Assemble Wiring Diagram Wrap Timers 32 PLC Ladder Diagram List of Input and output used

3 Introduction Congratulations! Your purchase of a Kalamazoo Model 939 Window Wrapper System will provide you with years of efficient spiral stretch wrapping of your windows. Your investment will ensure that your products will arrive cleaner, with less damage and pilferage at their destination at a lower cost to you. Warranty Kalamazoo Packaging Systems products carry a LIMITED LIFETIME WARRANTY on all K.P.S. manufactured components; all parts not manufactured by Kalamazoo Packaging Systems will be subject to the original manufacturer s warranty. Kalamazoo Packaging systems, Inc. (KPS) agrees to furnish the purchaser, without charge, F.O.B. the factory, any part found to be defective in either material or workmanship during the warranty period, provided the purchaser gives immediate notice of any defect and description of that defect to KPS. KPS reserves the right to inspect any defective part to verify the defect and to determine probable cause of same. The liability of KPS under this warranty is limited to furnishing replacements for defective parts, and unless otherwise agreed to in writing, the purchaser shall bear the expense of installation. Failure of equipment or parts due to abuse, misuse, neglect, incorrect operating techniques or power line drops or surges shall not constitute failure because of defective material or workmanship, and are expressly excluded from this warranty. The above is the only warranty with no other guarantees which extend beyond the above and the seller disclaims any implications including but not limited to a warranty of merchantability. Kalamazoo Packaging Systems, Inc. 3

4 Installation The stretch wrap machine, as delivered, is assembled, set up and ready to run. For the purpose of in-plant movement by fork lift truck, pockets (6x2 tubes) have been provided in the machine base. To move the machine, carefully insert forks into the pockets provided. DO NOT LIFT THE MACHINE AT ANY OTHER PLACE. USE ONLY THE POCKETS, COMPONENTS LOCATED UNDER THE TURNTABLE COULD BE DAMAGED. Place the machine in the proper location. After the machine is properly located it should be bolted to the floor through the tabs provided. Position the ramp in the proper position with ramp tabs against turntable base ring. The ramp may be bolted to the floor if desired. As shipped the turntable fixture stop position is perpendicular to the long axis of the machine. If desired, the orientation of the fixture may be changed 90 degrees by removing the four bolts in the center of the turntable and manually rotating the turntable disc 90 degrees and then replacing the bolts. If another fixture orientation is desired, remove the two bolts from the ends of the fixture and loosen the center bolt. Rotate the fixture to the desired orientation and tighten the center bolt. Drill and tap the table top for the 3/8-16 NC bolts on each end of the figure. For 115/1/60hz. plug into a 110 volt standard outlet 30 amp. For 230/1-3/60hz. connect power lines to the disconnect switch. Electrical Connection The System is now ready for operation. 1 Normal start position; Film lift - DOWN Platen - UP 2 Operator slides lower fixture to slightly less that the window width, centering on turntable, then sets window on fixture. Position top of window under upper fixture and lower top fixture (platen) to stabilize window. Wrapping Operation 3 Operator applies edge protectors as required and attaches film to window by tucking between window and lower fixture. 5 MOVE CLEAR OF TURNTABLE!! 6 Select program ( Short, Tall or Large ) 7 Operator starts wrap cycle. Note: The system automatically senses window wrap height with a switch on the film carriage. 8 When system has completed its automatic wrap cycle the operator cuts the film. 9 Raise the platen and remove the window Kalamazoo Packaging Systems, Inc. 4

5 DESCRIPTION OF WRAP CYCLE 1 Operator initiates the wrap cycle by pushing the START button. 2 Turntable starts. 3 Film tension comes on gradually. 4 After bottom wrap time delay film carriage starts up, travels until carriage switch senses proper height. 5 Film carriage stops and than the turntable will decelerate and index to the stop position. (Program Short ) 6 When operator raises top platen, the film lift will return to the down (start) position automatically. *If (Program Tall) is selected on the control console, the system will wrap to the bottom position before the turntable will decelerate and index to the stop position. * If (Program Large) is selected on the control console, the system will wrap the same as program TALL but in a lower speed so no damage is done to the product or the machine. 1 E-STOP: Stops all function by shutting off the main control relay and the PLC. (If the E-STOP button is pushed it must be left off for 30 sec. so the drives can stout down.) 2 STOP: Stop all function and reset the PLC. 3 START: Energizes the system. Starts the wrap cycle. 4 CYCLE INTERRUPT: Interrupts the cycle but does not reset timers. 5 PROGRAM: Selects the program that best suits the window being wrapped. 6 PLATEN RAISE: Raises the top platen boom. ( The film carriage will automatically return to the home position). 7 PLATEN LOWER: Lowers the top platen boom. 8 JOG: Operates turntable only. 9 FILM RAISE: Raises the film carriage. 10 FILM LOWER: Lowers the film carriage. Kalamazoo Packaging Systems, Inc. 5

6 Film Tension: Can be adjusted for proper film tension for different types and gauges of film. Located over the film tension controller. Film Lift Speed fast: Can be adjusted to change film overlap on program short and tall. Potentiometer located on the film lift AC Drive keypad. Factory set at 60 hz. Film Lift Speed for LARGE program: Parameter 5-01 in the Film Lift AC Drive. Factory set at 30 hz. Turntable Speed Fast: Can be adjusted to change the turntable speed in program short and tall. Potentiometer located on the turntable AC Drive keypad. Factory set at 60hz. 16 rpm Turntable speed for LARGE program: Parameter 5-01 in the Turntable AC Drive. Factory set at 30 hz. 8 rpm. To Program the Ac Drive parameters. (see the next three pages) AUTOMATION DIRECT GS-1 AC DRIVE PROGRAMMING To change a parameter in the GS-1 AC Drive. 1. Press the PROG/ENTER key. 0- will appear. 2. Use the up/down arrow key to navigate through the 10 different parameter groups. 3. Press the PROG/ENTER key will appear. 4. Press the PROG/ENTER key. 230 will appear. This parameter is 0-00, 230 motor voltage. If you would like to change the LARGE program turntable speed. (Factory set at 30 hz. 8 rpm.) 1. Press the PROG/ENTER key. 0- will appear. 2. Press the up arrow key until you get to 5-3. Press the PROG/ENTER key 5-00 will appear. 4. Press the up arrow key until you get to Press the PROG/ENTER key will appear Factory setting 6. Use the up or down arrow key to make changes. 7. After you have made the changes press the PROG/ENTER key. 8. The display will read END. 9. Press the DISPL/RESET until it reads H Programming change is complete. 6

7 939-M36 FILM LIFT GS-1 AC DRIVE New AC drives only: Before changing parameter reset the drive to factory defaults ( 9-08 = 99 ) After setting drive turn the keypad potentiometer to 45 HZ. For two inches of overwrap. If the customer would like a gap In the film turn the keypad potentiometer to 60 HZ DEFAULT MOTOR VOLTAGE DEFAULT MOTOR AMP DEFAULT MOTOR FREGUENCY DEFAULT MOTOR RPM DEFAULT MOTOR MAX. FREG DEFAULT RAMP TO STOP CHANGE ACCE. TIME CHANGE DEC. TIME DEFAULT ACCE. S-CURVE DEFAULT DEC. S-CURVE DEFAULT ACCE. TIME DEFAULT DEC. TIME DEFAULT METHOD TO USE DEFAULT ACCE 1-2 FREG DEFAULT DEC 1-2 FREG DEFAULT SKIP FREG DEFAULT SKIP FREG DEFAULT SKIP FREG DEFAULT SKIP FREG. BAND DEFAULT DC INJECTION LENEL DEFAULT DC INJECTION START-UP DEFAULT DC INJECTION STOPPING DEFAULT START PIONT DC INJECTION DEFAULT GENERAL PURPOSE DEFAULT SLIP COMP DEFAULT MANUAL TORQUE BOOST DEFAULT MID-PIONT FREG DEFAULT MID-PIONT VOLT DEFAULT MIN. OUTPUT FREG DEFAULT MIN. OUTPUT VOLT DEFAULT PW/M CARRIER FREG CHANGE EXTERNAL CONTROL TERMINALS,STOP DISABLED DEFAULT DI1-FWD./STOP DI2-REV/STOP CHANGE MULTI-SPEED BIT 2 ( CHANGE PARAMETER 3-03 FIRST ) CHANGE MULTI SPEED BIT DEFAULT AC DRIVE RUNNING DEFAULT DESIRED FREG DEFAULT DESIRED CURRENT DEFAULT KEYPAD POT DEFAULT NO OFFSET DEFAULT ANALOG INPUT OFFSET DEFAULT ANALOG INPUT GAIN DEFAULT ANALOG INPUT REV DEFAULT LOSS OF ACI DEFAULT JOG CHANGE MULTI SPEED 1 (LOW) DEFAULT MULTI SPEED DEFAULT MULTI SPEED THUR 9-42 DEFAULT 7

8 939-M36 PLATEN LIFT GS-1 AC DRIVE New AC drives only: Before changing parameter reset the drive to factory defaults (9-08 =99) DEFAULT MOTOR VOLTAGE DEFAULT MOTOR AMP DEFAULT MOTOR FREGUENCY DEFAULT MOTOR RPM DEFAULT MOTOR MAX. FREG DEFAULT RAMP TO STOP CHANGE ACCE. TIME CHANGE DEC. TIME DEFAULT ACCE. S-CURVE DEFAULT DEC. S-CURVE DEFAULT ACCE. TIME DEFAULT DEC. TIME DEFAULT METHOD TO USE DEFAULT ACCE 1-2 FREG DEFAULT DEC 1-2 FREG DEFAULT SKIP FREG DEFAULT SKIP FREG DEFAULT SKIP FREG DEFAULT SKIP FREG. BAND DEFAULT DC INJECTION LENEL DEFAULT DC INJECTION START-UP DEFAULT DC INJECTION STOPPING DEFAULT START PIONT DC INJECTION DEFAULT GENERAL PURPOSE DEFAULT SLIP COMP DEFAULT MANUAL TORQUE BOOST DEFAULT MID-PIONT FREG DEFAULT MID-PIONT VOLT DEFAULT MIN. OUTPUT FREG DEFAULT MIN. OUTPUT VOLT DEFAULT PW/M CARRIER FREG CHANGE EXTERNAL CONTROL TERMINALS,STOP DISABLED DEFAULT DI1-FWD./STOP DI2-REV/STOP DEFAULT MULTI-SPEED BIT DEFAULT MULTI SPEED BIT DEFAULT AC DRIVE RUNNING DEFAULT DESIRED FREG DEFAULT DESIRED CURRENT DEFAULT KEYPAD POT DEFAULT NO OFFSET DEFAULT ANALOG INPUT OFFSET DEFAULT ANALOG INPUT GAIN DEFAULT ANALOG INPUT REV DEFAULT LOSS OF ACI DEFAULT JOG DEFAULT MULTI SPEED 1 (LOW) DEFAULT MULTI SPEED DEFAULT MULTI SPEED THUR 9-42 DEFAULT 8

9 939-M36 TURNTABLE DRIVE New AC drives only: Before changing parameter reset the drive to factory defaults (9-08 =99) DEFAULT MOTOR VOLTAGE DEFAULT MOTOR AMP DEFAULT MOTOR FREGUENCY DEFAULT MOTOR RPM DEFAULT MOTOR MAX. FREG DEFAULT RAMP TO STOP CHANGE ACCE. TIME CHANGE DEC. TIME DEFAULT ACCE. S-CURVE DEFAULT DEC. S-CURVE CHANGE ACCE. TIME CHANGE DEC. TIME CHANGE METHOD TO USE DEFAULT ACCE 1-2 FREG CHANGE DEC 1-2 FREG DEFAULT SKIP FREG DEFAULT SKIP FREG DEFAULT SKIP FREG DEFAULT SKIP FREG. BAND DEFAULT DC INJECTION LENEL DEFAULT DC INJECTION START-UP DEFAULT DC INJECTION STOPPING DEFAULT START PIONT DC INJECTION DEFAULT GENERAL PURPOSE DEFAULT SLIP COMP DEFAULT MANUAL TORQUE BOOST DEFAULT MID-PIONT FREG DEFAULT MID-PIONT VOLT DEFAULT MIN. OUTPUT FREG DEFAULT MIN. OUTPUT VOLT DEFAULT PW/M CARRIER FREG CHANGE EXTERNAL CONTROL TERMINALS,STOP DISABLED CHANGE DI1-FWD./STOP DI2-REV/STOP CHANGE MULTI-SPEED BIT 2 ( CHANGE PARAMETER 3-03 FIRST ) CHANGE MULTI SPEED BIT DEFAULT AC DRIVE RUNNING DEFAULT DESIRED FREG DEFAULT DESIRED CURRENT DEFAULT KEYPAD POT DEFAULT NO OFFSET DEFAULT ANALOG INPUT OFFSET DEFAULT ANALOG INPUT GAIN DEFAULT ANALOG INPUT REV DEFAULT LOSS OF ACI DEFAULT JOG CHANGE MULTI SPEED 1 (LOW) CHANGE MULTI SPEED 2 (DEC.) DEFAULT MULTI SPEED THUR 9-42 DEFAULT 9

10 STRETCH WRAP SYSTEM ADJUSTMENTS Top of Window Overwrap: Film carriage limit switch Change overwrap by sliding knob located on the top platen arm up or down the channel. Film Up & Down Limit Switches: Loosen the wing nuts in the mounting base and slide limit switches up and down NOTE; The system automatically senses window wrap height, no adjustment of up limit switch is usually required. Platen Up & Down Limit Switches: does not require adjustments. GENERAL MAINTENANCE Warning!! MAKE SURE THAT POWER SUPPLY IS DISCONNECTED BEFORE ATTEMPTING TO SERVICE ANY COMPONENTS. IF THE POWER DISCONNECT IS OUT OF SIGHT, LOCK IT IN THE OPEN POSITION AND TAG IT TO PREVENT UNEXPECTED APPLICATION OF POWER. Cleaning Periodically clean dirt accumulations from machine, especially around moving parts and drive components, preferably by vacuuming. General Check and tighten any loose fasteners. check all electric connections and replace any worn or frayed cords. Kalamazoo Packaging Systems, Inc. 10

11 Lubrication Bearings The bearings have been greased at the factory and are ready to run. It is recommended that all mounted bearings and support wheels be relubricated with #3 lithium base grease every three months. Chains Clean, lubricate and adjust chains every month. Chain should be lubricated with a penetrating type commercial chain lube. Gear Reducers For new reducers, change the oil 120 hours after the reducer starts operating (based on 8 hours per day of operation). After the first oil change, change oil every 2000 operating hours, or every six months, whichever occurs first. Temperature Lubricant F AGMA # F AGMA #7 Certain conditions (dust, water, etc.) may require a change of lubricating periods as dictated by experience. CHAIN TENSIONS Film Lift Chain Tension - Loosen chain adjuster axle located at the top of the tower, move the chain adjuster on both sides equally until chain is tight, retighten the axle nut ( Do NOT OVER TIGHTEN). Film Lift Motor Chain Tension - Remove back lower cover of machine. Loosen four mounting bolts, tighten chain and retighten mounting bolts. Platen Lift Chain Tension - Loosen chain adjuster axle located at the top of the tower, move the chain adjusters on both sides equally until chain is tight, retighten the axle nut ( Do NOT OVER TIGHTEN). Platen Motor Chain Tension - Remove back lower cover of machine. Loosen four mounting bolts, tighten chain and retighten mounting bolts. Turntable Drive Chain - Loosen slide mounting bolts, tighten chain with tensioning screw provided, retighten mounting bolts. Kalamazoo Packaging Systems, Inc. 11

12 TROUBLESHOOTING When any problem develops, review the operating instructions. Diagnose specific problems and review the options below. Machine not running at all. 1. Check wall receptacle for power 2. Check power cord for cut. (Fork Lift Trucks damage cords.) 3. Push in the E-STOP button after 30 sec. turn to reset the E-Stop button This will reset the drives and the PLC. 4. Check all fuses. (Only replace with the same type and rating.) System does not automatically stop. 1. Check limit switch under the turntable disc to see if the limit switch arm is hitting the cam. Carriage Malfunction: 1. Push stop to clear the system and try operating it again. DISCONNECT POWER FROM MACHINE. 2. Check all limit switches for damage, sticking or internal shorts. 3. Open cabinet and check that all relays are firmly seated in their bases. 4. Visually inspect for loose wires and for any signs of arcing or burning of any of the components. 5. It is advisable to call for technical assistance at this time. (616) Technical and Customer Service is available from Kalamazoo Packaging Systems, Inc., Monday thru Friday 7:30 A.M. to 4:00 P.M. (EST). Stock is maintained on parts to allow us to ship the same day on most orders. If you have a problem, we want to know about it! Please call and report any difficulties you may encounter. Local - (616) National - (800) Kalamazoo Packaging Systems, Inc. 12

13 13

14 14

15 Kalamazoo Packaging Systems ITEM PART# GRAINGER DESCRIPTION QTY TOP SHAFT 5/8-11 x 4-1/2 HEX HEAD CAP SCREW 2 2 L144 5/8 SAE WASHER TOWER CHAIN ADJUSTER (LEFT) TOWER TOP SPROCKET SHORT SPACER /8 x 1-3/8 PRE. FLANGE BEARING B22 TOWER TOP SPROCKET (KPS) TOWER TOP SPROCKET LONG SPACER 2 8 L141 5/8-11 NUT 2 9 L142 5/8 LOCK WASHER 2 10 L144 5/8 SAE WASHER TOWER CHAIN ADJUSTER (RIGHT) 2 12 L6 6/32 x 1-3/4 MACHINE SCREW B LIMIT SWITCH LEVER ARM B084 H.D. LIMIT SWITCH CORD GRIP 1/2 NPT W661 16/3 SJ CORD 4 17 G13 1/4-20 WING NUT LIMIT SWITCH BRACKET (HD) 2 19 L48 5/16 USS WASHER 2 20 L47 5/16 LOCK WASHER 2 21 L54 5/16-18x 1-1/2 SET SCREW 2 22 G35 3/8-24x 1-1/4 HEX HEAD CAP SCREW 8 23 G32 3/8 LOCK WASHER 8 24 G33 3/8 USS WASHER /4 2-BOLT FLANGE BEARING B22x 3/4 SPROCKET B12x 3/4 SPROCKET (SPIRAL) BOTTOM SHAFT 2 29 L2 3/16 x 3/16 x 3/4 KEYWAY 4 15

16 Kalamazoo Packaging Systems PARTS MANUAL: 939-M9 TOWER ITEM PART# GRAINGER DESCRIPTION QTY B22x 3/4 SPROCKET (PLATEN) TOWER CHAIN GUARD 1 32 G16 1/4-20 x 3/4 MACHINE SCREW 2 33 G16 1/4 SAE WASHER 8 34 G15 1/4 LOCK WASHER 8 35 G18 1/4-20x 3/4 HEX HEAD CAP SCREW LIFT MOTOR MOUNT 2 37 L48 5/16 USS WASHER 8 38 L47 5/16 LOCK WASHER 8 39 L48 5/16-18x 3/4 HEX HEAD CAP SCREW 8 40 L48 5/16 USS WASHER 1 41 L53 5/16-18x 1-1/2 HEX HEAD CAP SCREW 1 42 G41 3/8-16x 1 HEX HEAD CAP SCREW 8 43 G32 3/8 LOCK WASHER Z285 50:1 R/A REDUCER (FILM LIFT) 1 45 L2 3/16 x 3/16 x 3/4 KEYWAY 2 46 L2 3/16 x 3/16 x 3/4 KEYWAY B10x 5/8 SPROCKET #50 CHAIN x N v 3ph. 1/2hp. TEFC MOTOR (FILM LIFT) A247 CORD GRIP ea. 14ga. RED MTW WIRE/ 1ea. 14ga. GREEN Z284 60:1 R/A REDUCER (TOP PLATEN) N v 3ph. 1/2hp. TEFC MOTOR (PLATEN) ea. 14ga. RED MTW WIRE/ 1ea. 14ga. GREEN 1 16

17 Kalamazoo Packaging Systems PARTS MANUAL: 939-M9 TOWER ITEM PART # GRAINGER DESCRIPTION QTY 55 G43-1 3/8-16x 1-1/2 HEX HEAD CAP SCREW w/ CAN T TWISTPLATE 56 G43 3/8-16x 1-1/2 HEX HEAD CAP SCREW 2 57 L65 3/8 USS WASHER 8 59 G40 3/8-16x 1 HEX HEAD CAP SCREW 4 58 L64 3/8 LOCK WASHER 4 60 L63 3/8-16 NYLOCK NUT Z616 31:1 INLINE REDUCER (TURNTABLE) 1 62 L2 3/16 x 3/16 x 3/4 KEYWAY N v 3ph. 1/2hp. TEFC MOTOR (TURNTABLE) ea. 14ga. RED MTW WIRE/ 1ea. 14ga. GREEN M9 939-M9 TOWER & CABINET KPS NAME PLATE BASE CABINET COVER 1 68 G /4-20 BUTTON HEAD CAP SCREW

18 18

19 PARTS MANUAL: 939-M36 TABLE ITEM PARTS # GRAINGER # DESCRIPTION QTY TURNTABLE DISC L130 1/2-13 x 1-1/2 FLAT HEAD SOCKET CAP SCREW a TURNTABLE DRIVEN SPROCKET 1 4 G38 3/8-16 NYLOCK NUT 4 5 G32 3/8 LOCK WASHER 4 6 G33 3/8 USS WASHER X BOLT FLANGE BEARING 1 8 3/8-16x 1-1/2 ALEN HEAD FLAT TURNTABLE ROLLERS 4 10 L126 1/2-13 NYLOCK NUT 4 11 L132 1/2-13x 2-1/4 HEX HEAD CAP SCREW gr L6 6/32 x 1-3/4 MACHINE SCREW A096 LIMIT SWITCH (SPRING ARM) CORD GRIP 1/2 NPT W661 16/3 SJ CORD #50 TURNTABLE CHAIN B16x1 SPROCKET 1 18 l3 1/4 x 1/4 x 3/4 KEYWAY 1 19 G79 3/4-10 NUT M9-36 TURNTABLE BASE LOWER FIXTURE PLATE LOWER FIXTURE PRONG POSITIONING KNOB 2 24 G40 3/8-16x 1 HEX HEAD CAP SCREW 3 25 G32 3/8 LOCK WASHER 3 26 G33 3/8 USS WASHER 3 19

20 20

21 Kalamazoo Packaging Systems PARTS MANUAL: 939-M9 TOP PLATEN BOOM ARM ITEM PART # DESCRIPTION QTY KNOB SLIDE PLATE 1 2 G46 3/8 FENDER WASHER POSITION LOCKING KNOB w/ 3/8-24x 1-1/4 SET SCREW /4 CAM ROLLER /4 EXC. CAM ROLLER 4 6 G33 3/8 SAE WASHER 8 7 H5 3/8-24 NYLOCK JAM NUT CORD GRIP /3 COILED CORD 1 10 G33 3/8 SAE WASHER 8 11 G38 3/8-16 NUT /8-16 x 1.0 BRASS WEAR SCREW /3 SJ CORD PLATEN FIXTURE STOP CALLOR PLATEN FIXTURE STOP CUP 1 16 G35 3/6-24x 1-1/4 HEX HEAD CAP SCREW 4 17 G32 3/8 LOCK WASHER 4 18 G33 3/8 USS WASHER /4 2-BOLT FLANGE BEARING 2 20 G8 10/32 x 1-1/2 MACHINE SCREW H.D. LIMITS SWITCH H.D. LIMITS SWITCH LEVER ARM (ADJUSTABLE) M9-36 TOP PLATEN BOOM ARM M9-36 TOP FIXTURE M9-36 TOP FIXTURE PLUNGER 1 21

22 22

23 Kalamazoo Packaging Systems PARTS MANUAL: 939-M9 SUB PANEL ITEM PART# GRAINGER DESCRIPTION QTY TERMINAL STRIP 12 POLE MITSUBISHI PLC PDT 10a. RELAY PIN BASE POLE FUSE HOLDER a. FUSE (PLC) a. FUSE (BRAKE) /180v. DC CONTROLLER (BRAKE) PDT 30a. RELAY (MCR) POLE FUSE HOLDER a FUSE (MAIN) a. DISCONNECT POLE FUSE HOLDER a. FUSE (FILM LIFT) /2hp 110v 1ph. input 230v 3ph. output AC DRIVE POLE FUSE HOLDER a. FUSE (TOP PLATEN) /2hp 110v 1ph. input 230v 3ph. output AC DRIVE POLE FUSE HOLDER a. FUSE (TURNTABLE) /2hp 110v 1ph. input 230v 3ph. output AC DRIVE TERMINAL STRIP 12 POLE 3 23

24 24

25 Kalamazoo Packaging Systems PARTS MANUAL: 939 CONTROL CONSLOE ITEM PART# DESCRIPTION QTY M9a DECAL 939-M9a CONTROL CONSOLE DECAL E-STOP BUTTON PUSH OFF/TURN TO RESET RED MUSHROOMPUSH BUTTON (STOP) JOG 3-POSITION SELECTOR (PROGRAM) JOG 2-POSITION SELECTOR (TABLE JOG) GREEN PUSH BUTTON (START) WHITE PUSH BUTTON (PLATEN RAISE) YELLOW PUSH BUTTON (FILM RAISE) RED PUSH BUTTON(CYCLE INTERRUPT) BLACK PUSH BUTTON (PLATEN LOWER) BLUE PUSH BUTTON (FILM LOWER) a CONTROL CONSOLE NEMA 12 ENCLOSURE CONTROL CONSOLE ARM 1 14 G29 5/16-18x 1-1/2 FLAT HEAD 4 25

26 26

27 Kalamazoo Packaging Systems PARTS MANUAL: PRECESSION VARIABLE TENSION HEAD PARTS MANUAL: PRECESSION VARIABLE TENSION HEAD ITEM PART# DESCRIPTION QTY 1 G8 10/32 x 1-1/2 MACHINE SCREW H.D. LIMITS SWITCH H.D. LIMITS SWITCH LEVER ARM (ADJUSTABLE) /3 COILED CORD CORD GRIP 1 6 L3 3/16x 3/16x 3/4 KEYWAY /4 90v DC BRAKE TOP PLATE w/ NEMA 1 BOX 1 9 G40 3/8-16 x 1 HEX HEAD CAP SCREW 3 10 G32 3/8 LOCK WASHER 4 11 G33 3/8 SAE WASHER /8x 1-3/8 PER. FLANGE BEARING 2 13 G74 5/8 SPRING WASHER R PRE. VARIABLE TENSION BRAKE ROLLER /8x 1-3/8 FLANGE BEARING IR PRE. VARIABLE TENSION IDLER ROLLER IRS 5/8 G&P IDLER ROLLER SHAFT /8-16x 1-1/4 ALEN HEAD CAP SCREW 1 19 G29 5/16-18x 1-1/2 FLAT HEAD CAP SCREW DIA x 20 FILM CORE THRUST WASHER /4 CAM ROLLER /4 EXC. CAM ROLLER 4 24 G33 3/8 SAE WASHER 8 25 H5 3/8-24 NYLOCK JAM NUT 8 26 G33 3/8 SAE WASHER 4 27 G38 3/8-16 NUT /8-16 x 1.0 BRASS WEAR SCREW BASE PLATE 1 27

28 28

29 29

30 30

31 31

32 Model # 939-M9 Window / Panel Stretch Wrapper Timers Timer # Description Time T0 Bottom timer short program K50 T1 Bottom timer tall program K60 T2 Bottom timer large program K70 T3 Top timer short program K10 T4 Top timer tall program K70 T5 Top timer large program K80 T6 Autostop short program K20 T7 Autostop tall program K20 T8 Autostop large program K50 T9 Time to go pass autostop limit switch K10 DO NOT CHANGE T10 Film tension start delay K30 T11 Film tension off delay K80 To make changes to the timers call Kalamazoo Packaging System, Inc. 1(800)

33 33

34 34

35 35

36 36

37 37

38 38

39 39

40 40

41 41

42 42

43 43