Medium Voltage Catalogue 2013

Transcription

1 Medium Voltage Catalogue 2013 D813 SAP.Nr

2 Medium Voltage 2013 Data, values and illustrations given in this documentation are correct and reliable according to the current state of our knowledge. They represent however no obligatory characteristic warranty. Such a warranty is made only by our product standards. The user of this product must decide on his own responsibility on its suitability for the intended application. Our liability for these products exclusively depends on our general trading conditions. Changes in the sense of technical progress and misprint reserved. 2013, CEPACK GmbH. All Rights Reserved. Safe connections 2

3 Page Introduction Cellpack Technology 4 Cable accessories for unscreened cables 24 Cable accessories for screened cables 30 Cable accessories for paper-insulated cables 70 Cable accessories for screened cables according to British Standard 90 Cable accessories for the industries 102 Accessories 106 Index 136 3

4 Introduction Cable accessories are indispensable components of a cable network which exert a direct influence on its quality. The same level of operational safety must be guaranteed for the accessories as for the cable itself. Due to high operational costs incurred by medium voltage networks, it is necessary to avoid outages. The safe, quick and easy assembly of cable accessories is therefore essential for network reliability. Exceptional innovative solutions are thus required to ensure that excessive demands are not placed on the capabilities of assembly staff. We produce innovative, high-performance cable accessories for medium voltage networks based on the stress control system developed by Cellpack. Cellpack Villmergen Switzerland Cellpack Tiengen Germany Cellpack Radeberg Germany We offer a full range of products for a wide variety of applications using heat shrink, silicone, slip-on, plug-in and cast resin technologies which comply with the standard requirements for energy suppliers and the set industrial norms. The system components of all of our cable accessories are compatible so as to ensure safe and reliable functioning. As a result of intensive testing carried out in our laboratories, as well as numerous type tests carried out in international test facilities, we are able to guarantee an operationally reliable conductor connection, an adequate insulation level and excellent resistance against all environmental influences for all our cable accessories. All our medium voltage products are tested according to DIN VDE 0278, CENEEC HD 629.1, HD 629.2, IEC and comply with IEEE and BS requirements. Cellpack Almere Buiten Netherlands Cellpack udres France Cellpack Barcelona Spain Cellpack Warschau Poland Cellpack Melaka Malaysia Cellpack Singapur Far East 4

5 Stress control in MV cable accessories Removal of the cable insulation and the outer semi-conducting layer when connecting or terminating medium voltage cables results in damage to the cable structure. In addition to this, the electric field becomes strongly inhomogeneous at particular points. During this process the electric field strength value greatly increases, resulting in a risk of partial discharge, breakdown or spikes. Stress control influences the strong inhomogeneous field distribution at the cable end so as to reduce the high field strengths to a non-critical value. Refractive stress control is the most suitable method for medium voltage cable accessories. It offers the following significant advantages over other methods: eaner stress control element design, enabling the development of compact solutions which are very easy to assemble. Reduced sensitivity to incorrect positioning or incorrect cable preparation, allowing compensation for errors made during assembly. Cellpack Technologie Refractive stress control Refractive stress control influences the electric field by means of a combination of two insulation materials having different dielectric strengths. The insulation material with the higher dielectric constant is placed in the area at which the higher electrical field strength occurs. The use of the term refractive derives from the fact that the process deflects electric field lines which cross the surface of these materials at an angle(see Figure 1). (Fig. 1: Interruption of electric field lines at the point of transition between materials with different dielectric constants) 5

6 When using the above principle in medium voltage cable accessories, a thin stress control and insulation layer is placed in the region above the strippable edge of the outer semi-conducting layer (for cables with plastic insulation), or above the Hochstädter foil or lead sheath (for cables with paper insulation), or above the core insulation when the cable insulation has been removed. This layer has a considerably higher dielectric constant (εr) than the insulating material of the cable itself. This results in a targeted reduction of the original field strength (see Fig. 2). Cellpack Technologie (Fig. 2: Comparison of lines of equipotentiality in a plastic-insulated cable with the insulation removed, with and without refractive stress control). Stress control element (FSE) In addition to stress control itself, the positioning of the contact surfaces of cable insulation and accessory during assembly is very significant. Trapped air can result in partial discharge even at low voltages, particularly in the area of stress control, resulting in the breakdown of the cable accessory. In order to avoid these problems, we have developed a stress control element (FSE) made from a special silicone rubber, manufactured using injection-moulding. This product owes its uniqueness to its optimised design and to the specific properties of the HTV silicone rubber used. The dimensions of the cylinder body have been carefully selected to ensure that a single stress control element size is compatible with a wide range of medium voltage cable cross-sections. The dimensions of the inner cylindrical area allow the positioning of the FSE on the smallest possible cross-sectional area, where it expands to the correct size, thus exerting a permanent contact ressure on the base. The permanent high elasticity of the silicone ensures that a constant pressure is applied to the contact surface under all operating conditions. The high gas permeability of the special material constitutes a significant advantage. As a result of constant pressure on the contact surface, pockets of air arising during assembly will completely diffuse through the stress control material within a few minutes (Fig. 3). This protects the cable accessory against partial discharge under all operating conditions. (Fig. 3 Disappearance of an air bubble in the gap between the sleeve insulating body and the FSE) 6

7 Stress control elements can be slid over any cable safely, quickly and easily with the aid of the AH slip-on auxiliary device patented by Cellpack. Cellpack Technologie The slip-on auxiliary device has been designed so as to prevent damage to the inner cylindrical surface of the stress control element during assembly. 7

8 Hybrid technology Cellpack Technologie Hybrid technology is a modular system developed by Cellpack which combines components made from silicone rubber with high voltage resistant heat shrink products. This renders our cable accessories compatible with all existing medium voltage cable cross-sections and ensures maximum operational reliability. The full product range comprises plug-in straight-through and transition joints, indoor and outdoor terminations for single- and three-core cables, which comply with the standard requirements for energy suppliers and the set industrial norms. We also offer products based on customer specifications. Advantages Our hybrid cable accessories offer a high level of operational safety in addition to the following advantages: Safe, quick and easy installation Compact and space-saving Unlimited shelf life Adaptability 8

9 Hybrid joint system The main insulation material used in hybrid plug-in straight-through and transition joints consists of a combination of heat-shrink tubing supplied in telescoped form. The insulation materials are manufactured from high-performance polymeric materials with appropriate additives. The resulting joint system can be positioned and heat-shrunk onto the cable cores to be connected from the park position during assembly safely, quickly and easily. Cellpack Technologie The dimensions of the tube are selected to ensure a defined insulation wall thickness for the appropriate voltage level and cable cross-section. Stress control is achieved by slipping the silicone rubber stress control elements onto the prepared cable end using the patented slip-on auxiliary device. A special filling tape possessing exceptionally high dielectric strength and oil-resistant properties is used to restrict the field strength around the connectors and to prevent air pockets. Assembly is safe, quick and easy, due to the compatibility of all system components. Diagram of type CHMSV straight-through joint: 1. Connector 2. Field control tape 3. Joint insulation 4. Stress control element 5. Screen continuity 6. Outer sheath Cable screen continuity for single-core cables is achieved in accordance with current standards by means of a copper braid sleeve, which is connected to the copper wire and/or tape screen using pressure springs. Other types of shielded connections are available upon request. A heat- shrink tube with integrated hot-melt adhesive developed especially for the outer sheath and possessing very high mechanical strength guarantees a reliable seal. 9

10 Hybrid termination system Stress control within cable terminations is achieved in the same way as for the hybrid joint system- by simply slipping the tried and tested silicone rubber stress control elements onto the cable end, using the patented slip-on auxiliary device. Cellpack Technologie A sealing tape- another well-established product- is wrapped around the cable shielding and the cable lug to provide a reliable seal. A heat-shrink spreader cap with integrated heat-sealing adhesive provides a reliable seal for the connector distributor and the cable sheath in the distribution region of three-core cables. The main insulation material used in terminations is heatshrink tubing, which is manufactured from high-performance tracking resistant polymeric materials. To establish the necessary creepage distances, highly-elastic shields manufactured from tracking resistant silicone rubber are installed on the tubing after shrinking. Once again, the use of the patented slip-on auxiliary device ensures safe, quick and easy assembly. Diagram of type CHE termination: 1. Cable lug 2. Seal 3. Stress control element 4. eakage current-resistant outer tube 5. eakage current-resistant silicone shield 10

11 Cellpack Technologie The exceptional hydrophobic properties, resistance to leakage current and high elasticity of silicone rubber guarantee sustained operational safety. All materials characterised by exceptionally high resistance to ozone and UV radiation have undergone decades of rigorous testing under challenging climatic conditions and have proven themselves in innumerable installations all over the world. Standard hybrid terminations are designed for challenging climatic conditions and comply with CENEEC and IEC requirements. 11

12 Contrax technology All primary components of our Contrax technology system are integrated into a single-piece insulating body. This reduces the number of cable accessory components, greatly simplifying assembly. Its compact, optimised design reduces the associated assembly, storage and transportation costs to the energy supplier. Cellpack Technologie Insulating bodies for joints and terminations are manufactured from high-voltage resistant silicone rubber using a controlled injection process. Rigorous quality control as well as high-voltage component testing during production ensures the technical reliability of all our Contrax cable accessories. Advantages Our Contrax cable accessories offer a high level of operational safety in addition to the following advantages: Safe, quick and easy installation Systems available for all cross sections Compact and space-saving Unlimited shelf life Adaptability 12

13 Contrax joint system The single-piece insulating body of Contrax plug-in straight-through joints consists of an inner conductive electrode which acts as a Faraday cage around the connector with the main insulating layer above it, and an outer semi-conducting layer. Each joint body comes equipped with an integrated slip-on auxiliary device for easy assembly and the prevention of damage during installation. Cellpack Technologie Diagram of CAM joint body: 1. Connector 2. Single-piece insulating body 3. Stress control element 4. Screen continuity 5. Outer sheath Stress control at the cable end is achieved as above, by simply sliding our tried and tested silicone rubber stress control element onto the prepared cable using the patented slip-on auxiliary device. A special feature of the Contrax joint is that the stress control element is also used to control the electric field on the inner semi-conducting layer of the insulating body at high voltage against the outer semi-conducting layer of the joint body at earth potential. Electric field strength and lines of equipotentiality of type CAM Contrax straight-through joints. 13

14 The resulting lean and compact design of the joint body has proven to be particularly suited to use in three-core cables, as the joint body can be placed on the prepared core insulation in park position in a safe and simple process. Cable screen continuity is achieved using a copper braid sleeve which is easily connected to the copper wire and/or tape screen using highly-elastic pressure springs. Other types of shielded connections are available to order. Cellpack Technologie Special outdoor protection systems for Contrax plug-in straight-through joints are based on cast resin technology, thus ensuring a reliable seal and high mechanical strength. 14

15 Contrax termination system Contrax terminations consist of a single-piece insulating body manufactured from a creepage tracking resistant silicone rubber using a quality-controlled injection moulding process. The stress control element and necessary shields are also integrated into the insulating body. The compact optimised design minimises assembly, storage and transportation costs to energy suppliers. The silicone rubber used is characterised by excellent resistance against ozone and UV radiation, as well as exceptional hydrophobic properties. Its unique design has undergone years of rigorous testing under challenging climatic conditions. Contrax terminations are designed for challenging climatic conditions and thus comply with CENEEC and IEC requirements. Cellpack Technologie Diagram of type CAE termination: 1. Cable lug 2. Seal 3. Single-piece insulating body with integrated stress control element Construction of Contrax terminations Hydrophobic properties of the silicone used 15

16 Assembly is carried out in a single-step process, in which the single-piece body is safely, quickly and easily slid onto the prepared cable end using the patented slip-on auxiliary device. Cellpack Technologie A silicone spreader cap using special cold-shrink technology, patented by Cellpack, and silicone tubes with an integrated slip-on auxiliary device are used in the distribution region of three-core cable, ensuring simple and accurate assembly. A special sealing tape provides a reliable seal at the cable shielding and around the cable lug. 16

17 Plug-in technology Plug-in technology consists of four components- the conductor connection, main insulation, stress control element and outdoor protection system- which are combined to form a single element. Cellpack Technologie This integrated system developed by Cellpack maximises the reduction of assembly, storage and transportation costs to energy suppliers. Compax and Cellplux plug-in connection technologies are the result of over 5 years of work in product development and constitute a perfect connection system for medium-voltage networks. Can be installed safely, quickly and easily Systems available for all cross sections Integrated system components Compact and space-saving Unlimited shelf life Tested and approved in accordance with CENEEC HD Comprehensive quality control carried out in accordance with ISO 9001 as well as electrical component checks during production ensure the technical reliability of all our plug-in cable accessories. 17

18 Compax plug-in straight-through joint This joint has been especially developed for connecting plastic-insulated medium voltage single-core cables. All system components are compatible to ensure that assembly is extremely safe, quick and easy. Cellpack Technologie This innovative integration concept allows for much of the assembly process, previously carried out on-site, to be performed under controlled conditions and subjected to electrical testing at the Cellpack factory. Only a few assembly steps remain to be performed on-site. Advantages: Safe, quick and easy assembly Only standard tools required Suitable for use in confined spaces Products available for all cross sections Robust design Reduction in storage and transportation costs Unlimited shelf-life 18

19 Insulation materials The insulation materials in the CKM joint are equipped with exceptional electrical and mechanical properties and are manufactured from high voltage- resistant silicone rubber in a controlled injection moulding process. Each individual material component has been subjected to years of extensive electrical and mechanical testing and has proven its reliability over decades of application. Cellpack Technologie Diagram of type CKM straight-through joint 1. Screw connector 2. Joint insulation 3. Insulating support 4. Stress control element 5. Screen continuity 6. Outer sheath 7. Seal Integrated screw connector A unique feature of the Compax connection system is that the insulating body of the joint comes equipped with a tried and tested integrated screw connection system. This screw connector is compatible with all cross-sections and has been designed to guarantee a reliable connection for both copper and aluminium conductors. The optimised design of the contact screws allows the use of a single standard tool for all cross-sections. Integrated field control The CKM joint insulation body comes equipped with the Cellpack refractive stress control system, a device which has been used time and time again by our customers all over the world. This permits the reduction of assembly errors due to poor cable preparation or incorrect positioning of the joint body. Stress control in the connector screw openings is achieved geometrically. 19

20 Cellplux plug-in connectors Cellplux plug-in cable connection components have been especially developed to connect plasticinsulated medium voltage cables. All system components are compatible to ensure that assembly is extremely safe, quick and easy. Cellpack Technologie This innovative integration concept allows for much of the assembly process, previously carried out on-site, to be performed under controlled conditions and subjected to electrical testing at the Cellpack factory. Only a few assembly steps remain to be performed on-site. Advantages: Cellplux plug-in cable connection components guarantee reliable operational safety and offer the following advantages: High level of operational safety Safe, quick and easy assembly Standard tools may be used Suitable for use in confined spaces Products available for all cross sections Robust design Unlimited shelf life 20

21 Insulating materials Insulation materials used in Cellplux plug-in cable components possess exceptional electrical and mechanical properties and are manufactured from high voltage resistant EPDM using a controlled injection moulding process. Stress control is achieved by means of the silicone stress control element, offering all the above-mentioned advantages. Each individual material component has been subjected to years of extensive electrical and mechanical testing and has proven its reliability over decades of application. Cellpack Technologie 1. Silicone stress control element 2. Screw-in cable lug with shear bolt screw and integrated bracket 3. Contact bolts with shear bolt screw 4. Inner electrode 5. Main insulation 6. Shielding 7. Screw-in insulating supports with capacitive test point 8. Protective cap 21

22 Screw-in cable lug and screw-in contact bolts Cellpack Technologie Cellplux plug-in cable components are equipped with a tried and tested screw-in cable lug system, compatible with all cross-sections, which has been designed to guarantee reliable connection for both copper and aluminium conductors. The optimised design of the contact bolts permits the use of a single Monventional tool for assembly across the entire range of cross sections. The shear bolt screw system is also used for CTS screwtype plug-in connection contact bolts connecting the cable lug to the connecting terminal. This eliminates the possibilty of errors during assembly. Stress control This system is also equipped with Cellpack s integrated refractive stress control system, which has a proven track record of reliability. This eliminates the possibility of incorrect cable preparation and dramatically reduces the number of possible assembly errors. Protection from exposed electrical parts Cellplux plug-in cable component shieldingaa is made from conductive EPDM rubber over 3 thick. All products have successfully undergone tests for insulation failure detection. 22

23 Quality system All production sites have been certified according to ISO 9001, 2008 revision and ISO 14001, 2004 revision. Cellpack Technologie 23

24 Medium Voltage 2013 For pros by pros 24

25 Cable accessories for unscreened cables Page Straight-through joints 26 Terminations 28 25

26 Straight-through joints Medium Voltage 2013 SMH3MS6 Three-core straight-through joint for armoured 3-core polymeric cables without semi-conducting layer up to 7.2 kv SMH3MS6 straight-through joints are suitable for three-core plastic-insulated cables (PVC, PE, XPE, EPR) with no outer semi-conducting layer. They allow the connection of cables with different cross sections, conductive materials and structure. Dimensions = ength Cable accessories for unscreened cables Compact dimensions Wide cross-section range Quick, safe and easy assembly Ready for iediate operation High mechanical strength Indoor Outdoor Underground Water Installation ducts Ductwork Note Connectors not included Storage conditions/shelf life Unlimited shelf life Scope of delivery Thick wall heat-shrinkable outer tubing with hot melt adhesive Inner jacket sleeve Copper braid tube Pressure spring Assembly instructions max. Ø of connector max. connector length Nominal cross section ² ) 3.6/6 (7.2)kV - 3.8/6.6 (7.2)kV MS SMH MS MS Appropriate connectors must be ordered separately. 26

27 Straight-through joints M...MS6 Three-core straight-through joint for armoured 3-core polymeric cables without semi-conducting layer up to 7.2 kv M.MS6 straight-through joints are suitable for three-core plastic-insulated cables (PVC, PE, XPE, EPR) with no outer semi-conducting layer. They allow the connection of cables with different cross sections, conductive materials and structure. They do not contain any substances which inhibit paint wetting and are suitable for use in the automotive industry. Dimensions = ength D = Diameter Quick, safe and easy assembly Resistant to chemical agents ongitudinally and transversely watertight High mechanical strength Indoor Outdoor Underground Water Installation ducts Ductwork Note Connectors not included Scope of delivery Distance sleeve Hydrolysis resistance PUR type EG cast-resin, containing the correct volume ready for mixing. Packed in practical and easy-to-use two chamber bags Transparent plastic moulds Copper braid tube Hose clamp Fill and air-release funnel PVC insulation tape Protective gloves Assembly instructions Cable accessories for unscreened cables Nominal concentric conductor 1 2 D1 D2 D3 Cable-Ø cross section nominal cross section per conductor ² ² ) 3.6/6 (7.2)kV - 3.8/6.6 (7.2)kV M4 MS /25-50/ M5 MS /70-95/ M6 MS / / Appropriate connectors must be ordered separately. 27

28 Terminations Medium Voltage 2013 SEEV Three-core indoor termination for armoured 3-core polymeric cables without semi-conducting layer up to 7.2 kv Terminations SEEV for indoor applications are suitable to cover armoured three-core polymeric cables (PVC, PE, XPE, EPR) without semi-conducting layer. Dimensions = ength Cable accessories for unscreened cables Compact dimensions Wide conductor and cross-section range High mechanical strength Quick, safe and easy assembly Indoor Note Cable lugs not included Storage conditions/shelf life Unlimited shelf life Scope of delivery Core insulating tubes (tracking resistant) Spreader cap Filling tape Earthing accessories Sealing tape Assembly instructions Appropriate cable lugs must be ordered separately. Nominal cross section ² ) 3.6/6 (7.2)kV - 3.8/6.6 (7.2)kV SEEV

29 Terminations SEEV-F Three-core outdoor termination for armoured 3-core polymeric cables without semi-conducting layer up to 7.2 kv Terminations SEEV -F for outdoor applications are suitable to cover armoured three-core polymeric cables (PVC, PE, XPE, EPR) without semi-conducting layer. Dimensions = ength Ø S = Diameter of cable shed Compact dimensions Wide conductor and cross-section range High mechanical strength Quick, safe and easy assembly Outdoor Note Cable lugs not included Storage conditions/shelf life Unlimited shelf life Scope of delivery Core insulating tubes (tracking resistant) Filling tape Silicone sheds Earthing accessories Sealing tape Tracking resistant spreader cap Assembly instructions Cable accessories for unscreened cables U0 ) 3.6/6 (7.2)kV - 3.8/6.6 (7.2)kV SEEV-F Appropriate cable lugs must be ordered separately. Nominal cross section ² Ø S

30 30 Medium Voltage 2013

31 Medium Voltage 2013 Cable accessories for screened cables Page Straight-through joints for single-core cables 32 Termination for single-core cables 37 Straight-through joints for 3-core cables 59 Termination for 3-core cables 63 Scaling the heights safely 31

32 Straight-through joints for single-core cables Medium Voltage 2013 CHMSV Single-core straight-through joint with screw connector for all polymeric single-core cables CHMSV straight-through joints are suitable for all three-core plastic-insulated cables (PVC, PE, XPE, EPR). They allow the connection of cables with different cross sections, conductive materials, semi-conducting layers (graphite-coated, removable or strippable) and screening (copper wire or tape). With screw connector. Dimensions = ength Cable accessories for screened cables Reliable stress control due to flexible silicone stress control elements For both copper and aluminium conductors For all cables with copper wire or tape screen Wide conductor and cross-section range Quick, safe and easy assembly Ready for iediate operation Suitable for a wide range of applications due to innovative integrated screw connector Indoor Outdoor Underground Water Installation ducts Ductwork Note Incl. Screw connectors Joints with a range of U m = 12 kv must be used for cables of U m = 7.2 kv. (Check minimum diameter over conductor insulation). min. Ø over conductor insulation after removal of outer semi-conducting layer Heat-shrinkable straight-through joints, larger cross section on request Storage conditions/shelf life Unlimited shelf life Scope of delivery Thick wall heat-shrinkable insulation tubing Thick wall heat-shrinkable outer tubing with hot melt adhesive Silicone stress-control elements Copper braid tube Pressure springs Innovative screw connector with conductive sheath Stress control filling tape (blue) Assembly instructions Tests CENEEC HD (DIN VDE 0278, part 629-1) Nominal cross section ² 12kV 17.5kV 24kV 36kV ) 6/10 (12)kV /11 (12)kV CHMSV 12kV ) 8.7/15 (17.5)kV CHMSV 17kV ) 12/20 (24)kV /22 (24)kV CHMSV 24kV ) 18/30 (36)kV - 19/33 (36)kV CHMSV 36kV

33 Straight-through joints for single-core cables CHM Single-core straight-through joint for all polymeric single-core cables CHM straight-through joints are suitable for all single-core plastic-insulated cables (PVC, PE, XPE, EPR). They allow the connection of cables with different cross sections, conductive materials, semi-conducting layers (graphite-coated, removable or strippable) and screening (copper wire or tape). Suitable for compression connectors. Dimensions = ength Reliable stress control due to flexible silicone stress control elements For all cables with copper wire or tape screen Wide conductor and cross-section range Quick, safe and easy assembly Ready for iediate operation Indoor Outdoor Underground Water Installation ducts Ductwork Note Compression connectors not included Joints with a range of U m = 12 kv must be used for cables of U m = 7.2 kv. (Check minimum diameter over conductor insulation). Storage conditions/shelf life Unlimited shelf life Scope of delivery Thick wall heat-shrinkable insulation tubing Thick wall heat-shrinkable outer tubing with hot melt adhesive Silicone stress-control elements Copper braid tube Pressure springs Stress control filling tape (blue) Assembly instructions Tests CENEEC HD (DIN VDE 0278, part 629-1) Cable accessories for screened cables 33

34 Straight-through joints for single-core cables Medium Voltage 2013 Cable accessories for screened cables min. Ø over conductor insulation after removal of outer semiconducting layer max. Ø of connector max. connector length Nominal cross section ² 12kV 17.5kV 24kV 36kV ) 6/10 (12)kV /11 (12)kV CHM 12KV ) 8.7/15 (17.5)kV CHM 17KV ) 12/20 (24)kV /22 (24)kV CHM 24KV ) 18/30 (36)kV - 19/33 (36)kV CHM 36KV Armour continuity kit must be ordered separately. Appropriate compression connector must be ordered separately. 34

35 Straight-through joints for single-core cables CAM-S Single-core straight-through joint for all polymeric single-core cables CAM-S straight-through joints are suitable for all single-core plastic-insulated cables (PVC, PE, XPE, EPR). They allow the connection of cables with different cross sections, conductive materials, semi-conducting layers (graphite-coated, removable or strippable) and screening (wire or tape screen). Suitable for compression connectors. Dimensions = ength Reliable stress control due to flexible silicone stress control elements Wide conductor and cross-section range Ready for iediate operation Silicone slip-on components for quick, safe and easy assembly Indoor Outdoor Underground Water Installation ducts Ductwork Note Compression connectors not included Joints with a range of U m = 12 kv must be used for cables of U m = 7.2 kv. (Check minimum diameter over conductor insulation). min. Ø over conductor insulation after removal of outer semiconducting layer max. connector length Storage conditions/shelf life Unlimited shelf life Scope of delivery Thick wall heat-shrinkable outer tubing with hot melt adhesive Silicone stress-control elements Silicone joint body with integrated semi-conducting layer (individually tested) Copper braid tube Pressure springs Semi-conducting tape Assembly instructions Tests CENEEC HD (DIN VDE 0278, part 629-1) Nominal cross section ² ) 6/10 (12)kV /11 (12)kV CAM-S 12kV ) 12/20 (24)kV /22 (24)kV CAM-S 24kV Appropriate compression connector must be ordered separately. 12kV 24kV Cable accessories for screened cables 35

36 Straight-through joints for single-core cables Medium Voltage 2013 CKM Single-core straight-through joint with screw connector for all polymeric single-core cables CKM straight-through joints are suitable for all single-core plastic-insulated cables (PVC, PE, XPE, EPR) with different types of semi-conducting layers (graphite-coated, removable or strippable) and screening (wire or tape screen) up to a maximum network voltage of 24kV. With screw connectors integrated. Dimensions = ength H = Heigth B = Width Cable accessories for screened cables Compact design Quick, safe and easy assembly With integrated screw connectors Ready for iediate operation Resistant to alkaline earth elements Moisture-resistant Corrosion-resistant Superior mechanical properties B Indoor Underground Installation ducts H min. Ø over conductor insulation after removal of outer semi-conducting layer Storage conditions/shelf life Unlimited shelf life Scope of delivery Double plug Joint body with integrated outer housing, inner semi-conducting layer, silicon stress-control element and shear-bolt connector Pressure springs Padding tape Housing cover with integrated seal Protective sleeve with slide-on applicator Assembly instructions Tests CENEEC HD (DIN VDE 0278, part 629-1) Nominal cross section ² 12kV 17.5kV 24kV ) 12/20 (24)kV /22 (24)kV CKM 24kV

37 Termination for single-core cables CHE-I Single-core indoor termination for all polymeric single-core cables CHE-I terminations are suitable for all single-core plastic-insulated cables (PVC, PE, XPE, EPR) with different types of semi-conducting layers (graphite-coated or strippable) and screening (copper wire or tape). Dimensions = ength Ø S = Diameter of cable sheds Flexible silicone stress control elements ensure reliable stress control under all operating conditions Combination of slip-on and heat-shrink components Wide cross-section range Quick, safe and easy assembly Ready for iediate operation Indoor Note Cable lugs not included 12 kv terminations must be used for 7.2 kv cables (Check minimum diameter over conductor insulation). Each unit contains materials for one set of three terminations. Storage conditions/shelf life Unlimited shelf life Scope of delivery 1 Set for 3 phases Tracking-resistant heat-shrink tubing Silicone stress-control elements Silicone sheds Sealing tape Assembly instructions Tests CENEEC HD (DIN VDE 0278, part 629-1) Cable accessories for screened cables 37

38 Termination for single-core cables Medium Voltage 2013 Cable accessories for screened cables min. Ø over conductor insulation after removal of outer semi-conducting layer Number of sheds per phase Ø S Nominal cross section ² 12kV 17.5kV 24kV 36kV ) 6/10 (12)kV /11 (12)kV CHE-I 12kV ) 8.7/15 (17.5)kV CHE-I 17kV ) 12/20 (24)kV /22 (24)kV CHE-I 24kV ) 18/30 (36)kV - 19/33 (36)kV CHE-I 36kV Appropriate cable lugs must be ordered separately. EGA earthing kit for cables with tape screen must be ordered separately. 38

39 Termination for single-core cables CHE-F Single-core outdoor termination for all polymeric single-core cables CHE-F terminations are suitable for all single-core plastic-insulated cables (PVC, PE, XPE, EPR) with different types of semi-conducting layers (graphite-coated or strippable) and screening (copper wire or tape). Dimensions = ength Ø S = Diameter of cable sheds Flexible silicone stress control elements ensure reliable stress control under all operating conditions Combination of slip-on and heat-shrink components Wide cross-section range Quick, safe and easy assembly Ready for iediate operation Outdoor Note Cable lugs not included 12 kv terminations must be used for 7.2 kv cables (Check minimum diameter over conductor insulation). Each unit contains materials for one set of three terminations. Storage conditions/shelf life Unlimited shelf life Scope of delivery 1 Set for 3 phases Tracking-resistant heat-shrink tubing Silicone stress-control elements Silicone sheds Sealing tape Assembly instructions Tests CENEEC HD (DIN VDE 0278, part 629-1) Cable accessories for screened cables 39

40 Termination for single-core cables Medium Voltage 2013 Cable accessories for screened cables min. Ø over conductor insulation after removal of outer semi-conducting layer Number of sheds per phase Ø S Nominal cross section ² 12kV 17.5kV 24KV 36kV ) 6/10 (12)kV /11 (12)kV CHE-F 12kV ) 8.7/15 (17.5)kV CHE-F 17kV ) 12/20 (24)kV /22 (24)kV CHE-F 24kV ) 18/30 (36)kV - 19/33 (36)kV CHE-F 36kV Appropriate cable lugs must be ordered separately. EGA earthing kit for cables with tape screen must be ordered separately. 40

41 Termination for single-core cables CAESK-I Single-core indoor termination with screw cable lugs for all polymeric single-core cables CAESK-I terminations are suitable for all single-core plastic-insulated cables (PVC, PE, XPE, EPR) with different types of semi-conducting layers (graphite-coated or strippable) and screening (wire or tape screen). With screw cable lug. Dimensions = ength Ø S = Diameter of cable sheds Wide cross-section range Silicone slip-on components for quick, safe and easy assembly Ready for iediate operation Indoor Note Incl. Screw cable lugs 12 kv terminations must be used for 7.2 kv cables (Check minimum diameter over conductor insulation). min. Ø over conductor insulation after removal of outer semi-conducting layer Number of sheds per phase Ø S EGA earthing kit for cables with tape screen must be ordered separately. Storage conditions/shelf life Unlimited shelf life Scope of delivery 3 one-piece slip-on silicone terminations with integrated stress control element Silicone tube Sealing tape Screw cable lug for main conductor Assembly instructions Tests CENEEC HD (DIN VDE 0278, part 629-1) Nominal cross section ² 12kV 17.5kV 24kV 36kV ) 6/10 (12)kV /11 (12)kV CAESK-I 12kV ) 8.7/15 (17.5)kV CAESK-I 17kV ) 12/20 (24)kV /22 (24)kV CAESK-I 24kV ) 18/30 (36)kV - 19/33 (36)kV CAESK-I 36kV Cable accessories for screened cables 41

42 Termination for single-core cables Medium Voltage 2013 CAE-I Single-core indoor termination for all polymeric single-core cables CAE-I terminations are suitable for all single-core plastic-insulated cables (PVC, PE, XPE, EPR) with different types of semi-conducting layers (graphite-coated or strippable) and screening (wire or tape screen). Suitable for compression cable lugs. Dimensions = ength Ø S = Diameter of cable sheds Cable accessories for screened cables Wide cross-section range Silicone slip-on components for quick, safe and easy assembly Ready for iediate operation Indoor Note Compression cable lugs not included 12 kv terminations must be used for 7.2 kv cables (Check minimum diameter over conductor insulation). min. Ø over conductor insulation after removal of outer semi-conducting layer Number of sheds per phase Ø S Storage conditions/shelf life Unlimited shelf life Scope of delivery 3 one-piece slip-on silicone terminations with integrated stress control element Sealing tape Assembly instructions Tests CENEEC HD (DIN VDE 0278, part 629-1) Nominal cross section ² 12kV 17.5kV 24kV 36kV ) 6/10 (12)kV /11 (12)kV CAE-I 12kV ) 8.7/15 (17.5)kV CAE-I 17kV ) 12/20 (24)kV /22 (24)kV CAE-I 24kV ) 18/30 (36)kV - 19/33 (36)kV CAE-I 36kV Appropriate cable lugs must be ordered separately. Accessories for cables with tape screen must be ordered separately. 42

43 Termination for single-core cables CAESK-F Single-core outdoor termination with screw cable lugs for all polymeric single-core cables CAESK-F terminations are suitable for all single-core plastic-insulated cables (PVC, PE, XPE, EPR) with different types of semi-conducting layers (graphite-coated or strippable) and screening (wire or tape screen). With screw cable lug. Dimensions = ength Ø S = Diameter of cable sheds Wide cross-section range Silicone slip-on components for quick, safe and easy assembly Ready for iediate operation min. Ø over conductor insulation after removal of outer semiconducting layer Outdoor Note Incl. Screw cable lugs 12 kv terminations must be used for 7.2 kv cables (Check minimum diameter over conductor insulation). Number of sheds per phase Ø S EGA earthing kit for cables with tape screen must be ordered separately. Storage conditions/shelf life Unlimited shelf life Scope of delivery 3 one-piece slip-on silicone terminations with integrated stress control element Silicone tube Sealing tape Screw cable lug for main conductor Assembly instructions Tests CENEEC HD (DIN VDE 0278, part 629-1) Nominal cross section ² 12kV 17.5kV 24kV 36kV ) 6/10 (12)kV /11 (12)kV CAESK-F 12kV ) 8.7/15 (17.5)kV CAESK-F 17kV ) 12/20 (24)kV /22 (24)kV CAESK-F 24kV ) 18/30 (36)kV - 19/33 (36)kV CAESK-F 36kV Cable accessories for screened cables 43

44 Termination for single-core cables Medium Voltage 2013 CAE-F Single-core outdoor termination for all polymeric single-core cables CAE-F terminations are suitable for all single-core plastic-insulated cables (PVC, PE, XPE, EPR) with different types of semi-conducting layers (graphite-coated or strippable) and screening (wire or tape screen). Suitable for compression cable lugs. Dimensions = ength Ø S = Diameter of cable sheds Cable accessories for screened cables Wide cross-section range Silicone slip-on components for quick, safe and easy assembly Ready for iediate operation Outdoor Note Compression cable lugs not included 12 kv terminations must be used for 7.2 kv cables (Check minimum diameter over conductor insulation). min. Ø over conductor insulation after removal of outer semi-conducting layer Number of sheds per phase Ø S Storage conditions/shelf life Unlimited shelf life Scope of delivery 3 one-piece slip-on silicone terminations with integrated stress control element Sealing tape Assembly instructions Tests CENEEC HD (DIN VDE 0278, part 629-1) Nominal cross section ² 12kV 17.5kV 24kV 36kV ) 6/10 (12)kV /11 (12)kV CAE-F 12kV ) 8.7/15 (17.5)kV CAE-F 17kV ) 12/20 (24)kV /22 (24)kV CAE-F 24kV ) 18/30 (36)kV - 19/33 (36)kV CAE-F 36kV Appropriate compression cable lugs must be ordered separately. EGA earthing kit for cables with tape screen must be ordered separately. 44

45 Termination for single-core cables CWS 250A/M Elbow separable cable connector with capacitive measuring point for all polymeric single-core cables Cellplux elbow separable cable connectors are suitable for the connection of all plastic-insulated single-core cables (PVC,PE, XPE, EPR) with different types of semi-conducting layers (graphite-coated, removable or strippable) and screening (wire or tape screen) to switching equipment and transformers having plug-in connections for A outer cone system terminals (in accordance with EN 50180, EN and DIN 47636) up to a maximum network voltage of 24 kv. Dimensions with capacitive measuring point Individually tested Outer semi-conducting layer made of semi-conductive EPDM provides protection from exposed electrical parts. Cable sheath insulation fault test may be performed under voltage For both copper and aluminium conductors Quick, safe and easy assembly Suitable for a wide range of applications due to integrated screw cable lug Indoor B H min. Ø over conductor insulation after removal of outer semi-conducting layer = ength H = Heigth B = Width Storage conditions/shelf life Unlimited shelf life Scope of delivery Set of 3 separable cable connectors Silicone stress-control elements Earthing kit Assembly accessories Screw cable lug for main conductor Assembly instructions Tests CENEEC HD (DIN VDE 0278, part 629-1) Nominal cross section ² 12kV 17.5kV 24kV ) 6/10 (12)kV /22 (24)kV M/EGA CWS 250A 24kV M/EGA Cable accessories for screened cables 45

46 Termination for single-core cables Medium Voltage 2013 CGS 250A/M Straight separable cable connector with capacitive measuring point for all polymeric single-core cables Cellplux straight separable cable connectors are suitable for the connection of all plastic-insulated single-core cables (PVC,PE, XPE, EPR) with different types of semi-conducting layers (graphite-coated or strippable) and screening (wire or tape screen) to switching equipment and transformers having plug-in connections for A outer cone system terminals (in accordance with EN 50180, EN and DIN 47636) up to a maximum network voltage of 24 kv. Dimensions = ength B = Width Cable accessories for screened cables with capacitive measuring point Individually tested Outer semi-conducting layer made of semi-conductive EPDM provides protection from exposed electrical parts. Cable sheath insulation fault test may be performed under voltage For both copper and aluminium conductors Quick, safe and easy assembly Suitable for a wide range of applications due to integrated screw cable lug Indoor B min. Ø over conductor insulation after removal of outer semi-conducting layer Storage conditions/shelf life 12 months Unlimited shelf life Scope of delivery Set of 3 separable cable connectors Silicone stress-control elements Earthing kit Assembly accessories Screw cable lug for main conductor Assembly instructions Tests CENEEC HD (DIN VDE 0278, part 629-1) Nominal cross section ² 12kV 17.5kV 24kV ) 6/10 (12)kV /22 (24)kV M/EGA CGS 250A 24kV M/EGA

47 Termination for single-core cables CVS 250A Connector element up to 24kV for plug-in cable connector type CWS, CGS The CVS plug-in connector element is suitable for the connection of two elbow and/or straight separable CWS 250A or CGS 250A connectors. Its dimensions correspond to A outer cone systems according to EN 50180, EN and DIN Dimensions = ength Ø = Diameter Individually tested Easy assembly Safe and easy to handle Indoor Storage conditions/shelf life Unlimited shelf life Scope of delivery Set of 3 connectors Assembly accessories Assembly instructions Ø D ) 6/10 (12)kV /22 (24)kV CVS 24kV Cable accessories for screened cables 47

48 Termination for single-core cables Medium Voltage 2013 CWS 400A Elbow separable cable connector for all polymeric single-core cables Cellplux elbow separable cable connectors are suitable for the connection of all plastic-insulated single-core cables (PVC,PE, XPE, EPR) with different types of semi-conducting layers (graphite-coated or strippable) and screening (wire or tape screen) to switching equipment and transformers having plug-in connections for B outer cone system terminals (in accordance with EN 50180, EN and DIN 47636) up to a maximum network voltage of 36 kv. Dimensions = ength H = Heigth B = Width Cable accessories for screened cables Outer semi-conducting layer made of semi-conductive EPDM provides protection from exposed electrical parts. Cable sheath insulation fault test may be performed under voltage For both copper and aluminium conductors Quick, safe and easy assembly Suitable for a wide range of applications due to integrated screw cable lug With capacitive measurement Individually tested B Indoor H min. Ø over conductor insulation after removal of outer semi-conducting layer Nominal cross section ² 12kV 17.5kV 24kV 36kV ) 6/10 (12)kV /22 (24)kV EGA CWS 400A 24kV EGA ) 12/20 (24)kV - 19/33 (36)kV EGA CWS 400A 36kV EGA EGA earthing kit for cables with tape screen must be ordered separately. Storage conditions/shelf life Unlimited shelf life Scope of delivery Set of 3 separable cable connectors Silicone stress-control elements Earthing kit Assembly accessories Screw cable lug for main conductor Assembly instructions Tests CENEEC HD (DIN VDE 0278, part 629-1) 48

49 Termination for single-core cables CTS 630A T-separable cable connector for all polymeric single-core cables CTS shear bolt Cellplux separable cable connectors are suitable for connecting all plastic-insulated single-core cables (PVC, PE, XPE, EPR) with different types of semi-conducting layers (graphite-coated or strippable) and screening (wire or tape) to substations and transformers for a maximum system voltage of 36 kv, with plug-type connections for C Taper Male Plug System complying with EN and EN Dimensions = ength H = Heigth B = Width Individually tested Outer semi-conducting layer made of semi-conductive EPDM provides protection from exposed electrical parts. Cable sheath insulation fault test may be performed under voltage For both copper and aluminium conductors Quick, safe and easy assembly Suitable for a wide range of applications due to integrated screw cable lug With capacitive measurement Indoor B H min. Ø over conductor insulation after removal of outer semi-conducting layer Storage conditions/shelf life Unlimited shelf life Scope of delivery Set of 3 separable cable connectors Silicone stress-control elements Earthing kit Assembly accessories Screw cable lug for main conductor Assembly instructions Tests CENEEC HD (DIN VDE 0278, part 629-1) Nominal cross section ² 12kV 17.5kV 24kV 36kV ) 6/10 (12)kV /22 (24)kV EGA CTS 630A 24kV EGA EGA ) 12/20 (24)kV - 19/33 (36)kV EGA CTS 630A 36kV EGA EGA EGA EGA earthing kit for cables with tape screen must be ordered separately. More T-socket connexions on request Cable accessories for screened cables 49

50 Termination for single-core cables Medium Voltage 2013 CTKS 630A T-separable coupling connector for all polymeric single-core cables The CTKS coupling connectors are suitable for connecting all plastic-insulated single-core cables (PVC, PE, XPE, EPR) with different types of semi-conducting layers (graphite-coated or strippable) and screening (wire or tape), to the back of Cellplux separable cable connectors, model CTS 630 A. Dimensions = ength B = Width Cable accessories for screened cables Outer semi-conducting layer made of semi-conductive EPDM provides protection from exposed electrical parts. Cable sheath insulation fault test may be performed under voltage For both copper and aluminium conductors Quick, safe and easy assembly Suitable for a wide range of applications due to integrated screw cable lug With capacitive measurement Individually tested Indoor Storage conditions/shelf life Unlimited shelf life Scope of delivery Set of 3 coupling elements Silicone stress-control elements Earthing kit Assembly accessories Screw cable lug for main conductor Assembly instructions Tests CENEEC HD (DIN VDE 0278, part 629-1) min. Ø over conductor Nominal cross section insulation after ² B H removal of outer semi-conducting layer 12kV 17.5kV 24kV 36kV ) 6/10 (12)kV /22 (24)kV CTKS 630A 24kV EGA EGA ) 12/20 (24)kV - 19/33 (36)kV CTKS 630A 36kV EGA earthing kit for cables with tape screen must be ordered separately. 50

51 Termination for single-core cables CTKSA Coupling Surge Arrester Class 1 The CTKSA Surge Arrester is designed for the protection of encapsulated medium voltage installations with a maximum operating voltage of 24 kv. Its compact design allows direct connection to double-row CTS 630A screw plugs and complies with International Standard IEC Individually tested Protection from exposed electrical parts by EPDM outer protection Quick, safe and easy assembly Protection from exposed electrical parts With capacitive measurement System overvoltage (per unit of MCOV) Indoor Note Each unit contains materials for one set of three plugs Scope of delivery Set of three surge arresters, electrically tested Assembly accessories Secondary components Assembly instructions Maximum ambient temperature: 60 C (Per unit of Ur) Cable accessories for screened cables Time (seconds) CTKSA 12kV CTKSA 17kV CTKSA 19.5kV CTKSA 24kV Nominal leakage current I [ka] Rated voltage Ur [kv] Maximum Operating Voltage Uc [kv] Partial discharge at Uc [pc] < 5 < 5 < 5 < 5 Residual voltage [kv] at: Steep current impulse 1/20 μs Switching impulse current 125A Switching impulse current 500A ightning impulse current 8/20 μs

52 Termination for single-core cables Medium Voltage 2013 CTKSA Coupling Surge Arrester Class 2 The CTKSA Surge Arrester is designed for the protection of encapsulated medium voltage installations with a maximum operating voltage of 34 kv. Its compact design allows direct connection to double-row CTS 630A screw plugs and complies with International Standard IEC Cable accessories for screened cables Individually tested Protection from exposed electrical parts by EPDM outer protection Quick, safe and easy assembly Protection from exposed electrical parts System overvoltage (per unit of Uc) Indoor Note Each unit contains materials for one set of three plugs Scope of delivery Set of three surge arresters, electrically tested Assembly accessories Secondary components Assembly instructions Maximum ambient temperature: 60 C (Per unit of Ur) Time (seconds) CTKSA 34kV Nominal leakage current I [ka] 10 Rated voltage Ur [kv] 42 Maximum Operating Voltage Uc [kv] 34 Partial discharge at Uc [pc] < 5 Residual voltage [kv] at: Steep current impulse 1/20 μs Switching impulse current 250A 84 Switching impulse current 500A 89.6 ightning impulse current 8/20 μs

53 Termination for single-core cables CIK Voltage-proof Insulating Cap The CIK Voltage-proof Insulation Cap provides electrical insulation for s A 250A and C 630A bushings in encapsulated substations and transformers up to 36kV, in compliance with EN and EN Submersible Easy assembly Protection from exposed electrical parts Note Each unit contains materials for one set of three isulating caps Scope of delivery 3 x Voltage-proof Insulating caps Assembly accessories Assembly instructions Cable accessories for screened cables ) 6/10 (12)kV /22 (24)kV CIK 250A 24kV ) 6/10 (12)kV - 19/33 (36)kV CIK 630A 36kV

54 Termination for single-core cables Medium Voltage 2013 ZS-CTS Accessory Kit for CTS 630A Cellplux separable cable Connectors The ZS-CTS Accessory Kit is designed for the reinstallation of separable cable connectors in substations and transformers with bushings for C outer cone systems complying with EN 50180, EN The inclusion of the tried and tested contact pin with shear bolt in this kit eliminates the possibility of faulty assembly of cable systems. Cable accessories for screened cables Reinstallation of CTS separable Cable Connector Note Each unit contains materials for one set of three shear bolts Scope of delivery Set of 3 contact pins with shear bolt Assembly accessories Assembly instructions ZS-CTS

55 Termination for single-core cables Mounting Ring The Mounting Ring is designed to secure CWS 250A and CGS 250A Cellplux separable Cable Connectors to a special bushing for A outer cone systems. The Mounting Ring is simply placed in the prefabricated groove in the cable connector. The two components may then be mounted on the bushing together. Easy assembly Secure connection to special A bushing Scope of delivery 1 x Mounting Ring Cable accessories for screened cables Mounting Ring

56 Termination for single-core cables Medium Voltage 2013 CKS 630A Coupling connector up to 24kV for separable cable connector type CTS The CKS shear bolt coupling connector is intended for the connection of two CTS separable cable connectors up to 24 kv at up to a rated current of 630 A. The dimensions of the longer outer cone correspond to C outer cone systems in accordance with EN 50180, EN Dimensions = ength D = External diameter Cable accessories for screened cables Individually tested Easy assembly Safe and easy to handle Indoor 1 2 D Storage conditions/shelf life Unlimited shelf life Scope of delivery Set of 3 coupling elements Assembly accessories Assembly instructions D1 D2 ) 6/10 (12)kV /22 (24)kV CKS 630A 24kV

57 Termination for single-core cables CPES Test and earthing Kit The Test and Earthing Kit is designed for the establishment of galvanic connections between cable conductors and is compatible with all CTS and CTKS Cellplux T-plugs. Cable testing Cable fault location Phase compensation Earthing for work Scope of delivery 1 x Test adapter 3 x Earthing adapter 1 x Case Assembly instructions Cable accessories for screened cables ) 6/10 (12)kV - 19/33 (36)kV CPES Test and Earthing Kit

58 Termination for single-core cables Medium Voltage 2013 CPS Test-Kit The Test- Kit is designed for the establishment of galvanic connections between cable conductors and is compatible with all CTS and CTKS Cellplux T-plugs. Cable testing Cable fault location Phase compensation Scope of delivery 3 x Test adapter 1 x Case Assembly instructions Cable accessories for screened cables U0/U (Um) 6/10 (12)kV - 19/33 (36)kV CPS Test-Kit

59 Straight-through joints for 3-core cables CHMSV3 Three-core straight-through joint with screw connector for all 3-core polymeric cables CHMSV 3 straight-through joints are suitable for connecting three-core polymeric cable (PVC, PE, XPE, EPR). They allow the connection of cables with copper wire screen, with different cross sections, conductor materials, semi-conducting layers (graphite-coated, removable or strippable). Screw connectors included. Dimensions = ength Reliable stress control due to flexible silicone stress control elements For both copper and aluminium conductors For all cables with copper-wire screen Wide conductor and cross-section range Quick, safe and easy assembly Ready for iediate operation Suitable for a wide range of applications due to innovative integrated screw connector Indoor Outdoor Underground Water Installation ducts Ductwork Note Incl. screw connectors min. Ø over conductor insulation after removal of outer semi-conducting layer Storage conditions/shelf life Unlimited shelf life Scope of delivery Thick wall heat-shrinkable insulation tubing Thick wall heat-shrinkable outer tubing with hot melt adhesive Silicone stress-control element Copper braid tape Innovative screw connector with conductive sheath Stress control filling tape (blue) Screw connector for copper-wire screen Assembly instructions Nominal cross section ² 12kV 17.5kV 24kV 36kV ) 6/10 (12)kV /11 (12)kV CHMSV 3 12kV ) 8.7 /15 (17.5)kV CHMSV 3 17kV ) 12/20 (24)kV /22 (24)kV CHMSV 3 24kV ) 18/30 (36)kV - 19/33 (36)kV CHMSV 3 36kV Cable accessories for screened cables 59

60 Straight-through joints for 3-core cables Medium Voltage 2013 CHMSV3-1 Straight-through joint with screw connector for connecting from three-core with single-core polymeric cable CHMSV 3-1 straight-through joints are suitable for connecting three-core polymeric cable with three single-core polymeric cable (PVC, PE, XPE, EPR). They allow the connection of cables with copper wire screen, with different cross sections, conductor materials, semi-conducting layers (graphite-coated, removable or strippable). Screw connectors included. Dimensions = ength Cable accessories for screened cables Reliable stress control due to flexible silicone stress control elements For both copper and aluminium conductors For all cables with copper-wire screen Wide conductor and cross-section range Quick, safe and easy assembly Ready for iediate operation Suitable for a wide range of applications due to innovative integrated screw connector Indoor Outdoor Underground Water Installation ducts Ductwork Note Incl. screw connectors min. Ø over conductor insulation after removal of outer semi-conducting layer Storage conditions/shelf life Unlimited shelf life Scope of delivery Thick wall heat-shrinkable insulation tubing Thick wall heat-shrinkable outer tubing with hot melt adhesive Silicone stress-control element Copper braid tape Innovative screw connector with conductive sheath Stress control filling tape (blue) Screw connector for copper-wire screen Assembly instructions Nominal cross section ² 12kV 17.5kV 24kV 36kV ) 6/10 (12)kV /11 (12)kV CHMSV kV ) 8.7/15 (17.5)kV CHMSV kV ) 12/20 (24)kV /22 (24)kV CHMSV kV ) 18/30 (36)kV - 19/33 (36)kV CHMSV kV

61 Straight-through joints for 3-core cables CHM3 Three-core straight-through joint for all 3-core polymeric cables CHM3 straight-through joints are suitable for all three-core plastic-insulated cables (PVC, PE, XPE, EPR). They allow the connection of cables with different cross sections, conductive materials, semi-conducting layers (graphite-coated, removable or strippable) and screen (copper wire or tape). Suitable for compression connectors. Dimensions = ength Reliable stress control due to flexible silicone stress control elements Wide conductor and cross-section range Quick, safe and easy assembly Ready for iediate operation min. Ø over conductor insulation after removal of outer semiconducting layer Indoor Outdoor Underground Water Installation ducts Ductwork Note Compression connectors not included Joints with a range of U m = 12 kv must be used for cables of U m = 7.2 kv. (Check minimum diameter over conductor insulation). max. Ø of connector max. connector length Storage conditions/shelf life Unlimited shelf life Scope of delivery Thick wall heat-shrinkable insulation tubing Thick wall heat-shrinkable outer tubing with hot melt adhesive Silicone stress-control element Copper braid tube Pressure springs Stress control filling tape (blue) Assembly instructions Nominal cross section ² 12kV 17.5kV 24kV 36kV ) 6/10 (12)kV /11 (12)kV CHM3 12kV ) 8.7/15 (17.5)kV CHM3 17kV ) 12/20 (24)kV /22 (24)kV CHM3 24kV ) 18/30 (36)kV - 19/33 (36)kV CHM3 36kV Appropriate compression connectors must be ordered separately. Armour continuity kit for armoured cable available to order. Cable accessories for screened cables 61

62 Straight-through joints for 3-core cables Medium Voltage 2013 CAM3-S Three-core straight-through joint with heat-shrink outer protection for all 3-core polymeric cables CAM3-S straight-through joints are suitable for all three-core plastic-insulated cables (PVC, PE, XPE, EPR). They allow the connection of cables with different cross sections, conductive materials, semi-conducting layers (graphite-coated, removable or strippable) and screening (wire or tape screen). Suitable for compression connectors. Dimensions = ength Cable accessories for screened cables Reliable stress control due to flexible silicone stress control elements Wide conductor and cross-section range Ready for iediate operation Quick, safe and easy assembly Indoor Outdoor Underground Water Installation ducts Ductwork Note Compression connectors not included Joints with a range of U m = 12 kv must be used for cables of U m = 7.2 kv. (Check minimum diameter over conductor insulation). min. Ø over conductor max. connector length Storage conditions/shelf life Unlimited shelf life Scope of delivery Thick wall heat-shrinkable outer tubing with hot melt adhesive Silicone joint body with integrated semi-conducting layer (individually tested) Copper braid tube Pressure spring ubricant Protective gloves Silicone stress-control elements Assembly instructions Nominal cross section ² 12kV 17.5kV 24kV ) 6/10 (12)kV /22 (24)kV CAM3-S 24kV ) 6/10 (12)kV /11 (12)kV CAM3-S 12kV ) 8.7/15 (17.5)kV CAM3-S 17kV Appropriate compression connectors must be ordered separately. Armour continuity kit for armoured cable available to order. 62

63 Termination for 3-core cables CHE-3I(A) Three-core indoor termination for all 3-core polymeric cables CHE-3I(A) terminations are suitable for all three-core plastic-insulated cables (PVC, PE, XPE, EPR) with different types of semi-conducting layers (graphite-coated or strippable) and screening (copper wire or tape). Dimensions = ength Ø S = Diameter of cable shed Flexible silicone stress control elements ensure reliable stress control under all operating conditions Combination of slip-on and heat-shrink components Wide cross-section range Quick, safe and easy assembly Ready for iediate operation Indoor Note Cable lugs not included 12 kv terminations must be used for 7.2 kv cables (Check minimum diameter over conductor insulation). min. Ø over conductor insulation after removal of outer semi-conducting layer Number of sheds per phase Ø S Storage conditions/shelf life Unlimited shelf life Scope of delivery Tracking-resistant heat-shrink tubing Heat-shrink tube Silicone stress-control elements Silicone sheds Pressure spring Silicone stress control element Assembly accessories Sealing tape Assembly instructions Tests CENEEC HD (DIN VDE 0278, part 629-1) Nominal cross section ² 12kV 17.5kV 24kV 36kV ) 6/10 (12)kV /11 (12)kV CHE-3I(A) 12kV ) 8.7/15 (17.5)kV CHE-3I(A) 17kV ) 12/20 (24)kV /22 (24)kV CHE-3I(A) 24kV ) 18/30 (36)kV - 19/33 (36)kV CHE-3I(A) 36kV Appropriate cable lugs must be ordered separately. EGA earthing kit for cables with tape screen and armouring must be ordered separately. Cable accessories for screened cables 63

64 Termination for 3-core cables Medium Voltage 2013 CHE-3F(A) Three-core outdoor termination for all 3-core polymeric cables CHE-3F(A) terminations are suitable for all three-core plastic-insulated cables (PVC, PE, XPE, EPR) with different types of semi-conducting layers (graphite-coated or strippable) and screening (copper wire or tape). Dimensions = ength Ø S = Diameter of cable shed Cable accessories for screened cables Flexible silicone stress control elements ensure reliable stress control under all operating conditions Combination of slip-on and heat-shrink components Wide cross-section range Quick, safe and easy assembly Ready for iediate operation Outdoor Note Cable lugs not included 12 kv terminations must be used for 7.2 kv cables (Check minimum diameter over conductor insulation). min. Ø over conductor insulation after removal of outer semi-conducting layer Number of sheds per phase Ø S Appropriate cable lugs must be ordered separately. EGA earthing kit for cables with tape screen and armouring must be ordered separately. Storage conditions/shelf life Unlimited shelf life Scope of delivery Spreader cap Tracking-resistant heat-shrink tubing Silicone stress-control elements Silicone sheds Sealing tape Pressure spring Assembly accessories Assembly instructions Tests CENEEC HD (DIN VDE 0278, part 629-1) Nominal cross section ² 12kV 17.5kV 24kV 36kV ) 6/10 (12)kV /11 (12)kV CHE-3F(A) 12kV ) 8.7/15 (17.5)kV CHE-3F(A) 17kV ) 12/20 (24)kV /22 (24)kV CHE-3F(A) 24kV ) 18/30 (36)kV - 19/33 (36)kV CHE-3F(A) 36kV

65 Termination for 3-core cables CHE-3I(B) Three-core indoor termination for all 3-core polymeric cables CHE-3I(B) terminations are suitable for all three-core plastic-insulated cables (PVC, PE, XPE, EPR) with different types of semi-conducting layers (graphite-coated or strippable) and screening (copper wire or tape). Dimensions = ength Ø S = Diameter of cable shed Flexible silicone stress control elements ensure reliable stress control under all operating conditions Combination of slip-on and heat-shrink components Wide cross-section range Quick, safe and easy assembly Ready for iediate operation Indoor Note Cable lugs not included 12 kv terminations must be used for 7.2 kv cables (Check minimum diameter over conductor insulation). min. Ø over conductor insulation after removal of outer semi-conducting layer Number of sheds per phase Ø S Storage conditions/shelf life Unlimited shelf life Scope of delivery Tracking resistant spreader cap Tracking-resistant heat-shrink tubing Silicone stress-control elements Silicone sheds Pressure spring Assembly accessories Sealing tape Assembly instructions Tests CENEEC HD (DIN VDE 0278, part 629-1) Nominal cross section ² 12kV 17.5kV 24kV 36kV ) 6/10 (12)kV /11 (12)kV CHE-3I(B) 12kV ) 8.7/15 (17.5)kV CHE-3I(B) 17kV ) 12/20 (24)kV /22 (24)kV CHE-3I(B) 24kV ) 18/30 (36)kV - 19/33 (36)kV CHE-3I(B) 36kV Appropriate cable lugs must be ordered separately. EGA earthing kit for cables with tape screen must be ordered separately. Cable accessories for screened cables 65

66 Termination for 3-core cables Medium Voltage 2013 CHE-3F(B) Three-core outdoor termination for all 3-core polymeric cables CHE-3F(B) terminations are suitable for all three-core plastic-insulated cables (PVC, PE, XPE, EPR) with different types of semi-conducting layers (graphite-coated or strippable) and screening (copper wire or tape). Dimensions Cable accessories for screened cables Flexible silicone stress control elements ensure reliable stress control under all operating conditions Combination of slip-on and heat-shrink components Wide cross-section range Quick, safe and easy assembly Ready for iediate operation Outdoor Note Cable lugs not included 12 kv terminations must be used for 7.2 kv cables (Check minimum diameter over conductor insulation). min. Ø over conductor insulation after removal of outer semi-conducting layer Number of sheds per phase Ø S = ength Ø S = Diameter of cable shed Storage conditions/shelf life Unlimited shelf life Scope of delivery Tracking-resistant heat-shrink tubing Silicone stress-control elements Silicone sheds Sealing tape Pressure spring Assembly accessories Tracking resistant spreader cap Assembly instructions Tests CENEEC HD (DIN VDE 0278, part 629-1) Nominal cross section ² 12kV 17.5kV 24kV 36kV ) 6/10 (12)kV /11 (12)kV CHE-3F(B) 12kV ) 8.7/15 (17.5)kV CHE-3F(B) 17kV ) 12/20 (24)kV /22 (24)kV CHE-3F(B) 24kV ) 18/30 (36)kV - 19/33 (36)kV CHE-3F(B) 36kV Appropriate cable lugs must be ordered separately. EGA earthing kit for cables with tape screen must be ordered separately. 66

67 Termination for 3-core cables CAE-3I Three-core indoor termination for all 3-core polymeric cables CAE-3I terminations are suitable for all three-core plastic-insulated cables (PVC, PE, XPE, EPR) with different types of semi-conducting layers (graphite-coated or strippable) and screening (wire or tape screen). Suitable for compression cable lugs. Dimensions = ength Ø S = Diameter of cable shed Wide cross-section range Silicone slip-on components for quick, safe and easy assembly Ready for iediate operation Indoor Note Compression cable lugs not included 12 kv terminations must be used for 7.2 kv cables (Check minimum diameter over conductor insulation). min. Ø over conductor insulation after removal of outer semi-conducting layer Number of sheds per phase Ø S Storage conditions/shelf life Unlimited shelf life Scope of delivery 3 one-piece slip-on silicone terminations with integrated stress control element Silicone tube Silicone cold-shrink spreader cap Assembly accessories Sealing tape Assembly instructions Nominal cross section ² 12kV 17.5kV 24kV 36kV ) 6/10 (12)kV /11 (12)kV CAE-3I 12kV ) 8.7/15 (17.5)kV CAE-3I 17kV ) 12/20 (24)kV /22 (24)kV CAE-3I 24kV ) 18/30 (36)kV - 19/33 (36)kV CAE-3I 36kV Appropriate compression cable lugs must be ordered separately. EGA earthing kit for cables with tape screen must be ordered separately. Cable accessories for screened cables 67

68 Termination for 3-core cables Medium Voltage 2013 CAE-3F Three-core outdoor termination for all 3-core polymeric cables CAE-3F terminations are suitable for all three-core plastic-insulated cables (PVC, PE, XPE, EPR) with different types of semi-conducting layers (graphite-coated or strippable) and screening (wire or tape screen). Suitable for compression cable lugs. Dimensions = ength Ø S = Diameter of cable shed Cable accessories for screened cables Wide cross-section range Silicone slip-on components for quick, safe and easy assembly Ready for iediate operation Outdoor Note Compression cable lugs not included 12 kv terminations must be used for 7.2 kv cables (Check minimum diameter over conductor insulation). min. Ø over conductor insulation after removal of outer semi-conducting layer Number of sheds per phase Ø S Storage conditions/shelf life Unlimited shelf life Scope of delivery 3 one-piece slip-on silicone terminations with integrated stress control element Silicone tube Silicone cold-shrink spreader cap Assembly accessories Sealing tape Assembly instructions Nominal cross section ² 12kV 17.5kV 24kV 36kV ) 6/10 (12)kV /11 (12)kV CAE-3F 12kV ) 8.7/15 (17.5)kV CAE-3F 17kV ) 12/20 (24)kV /22 (24)kV CAE-3F 24kV ) 18/30 (36)kV - 19/33 (36)kV CAE-3F 36kV Appropriate compression cable lugs must be ordered separately. EGA earthing kit for cables with tape screen must be ordered separately. 68

69 Termination for 3-core cables Cable accessories for screened cables 69

70 We help you achieve the highest standards 70

71 Page Belted cables Transition joints 72 Straight-through joints 76 Terminations 77 Cable accessories for paper-insulated cables Hoechstaedterkabel Page Transition joints 79 Straight-through joints 81 Terminations 82 Three-core single lead sheath cables Transition joints 84 Straight-through joints 86 Terminations 87 71

72 Transition joints Medium Voltage 2013 M...MSPB6 Three-core transition joint from belted cable to polymeric cable without external conductive layer M.MSPB6 transition joints are suitable for transitions between paper-insulated lead cables and three-core cables with plastic insulation (PVC, PE, XPE, EPR) and no outer semi-conducting layer. They allow the connection of cables with different cross M.MSPB6 transition joints are suitable for transitions between paper-insulated lead cables and three-core cables with plastic insulation (PVC, PE, XPE, EPR) and no outer semi-conducting layer. They allow the connection of cables with different cross sections, conductive materials and structure. They do not contain any substances which inhibit paint wetting and are suitable for use in the automotive industry. Dimensions = ength D = Diameter Cable accessories for paper-insulated cables Quick, safe and easy assembly Resistant to chemical agents ongitudinally and transversely watertight High mechanical strength 1 2 D1 Appropriate connectors must be ordered separately. Indoor Outdoor Underground Water Installation ducts Ductwork Note Connectors not included D2 D3 Cable-Ø Scope of delivery Distance sleeve Hydrolysis-resistant PUR type EG cast-resin, containing the correct volume ready for mixing Transparent plastic moulds Spreader cap Armour continuity kit Fill and air-release funnel Heat-shrinkable tubing for sealing Assembly accessories Assembly instructions 3x Nominal cross section per conductor Polymeric cable ² ) 3.6/6 (7.2)kV - 3.8/6.6 (7.2)kV M4MSPB M5MSPB

73 Transition joints CHMPRSV 3-1 Transition joint with screw connectors, from belted cable to polymeric cables CHMPRSV3-1 hybrid transition joints for transition to three single-core plasticinsulated cables are suitable for both paper-insulated lead cables and Hochsta dter cables up to 17.5 kv. With screw connectors. Dimensions = ength Reliable stress control due to flexible silicone stress control elements Wide cross-section range Quick, safe and easy assembly Ready for iediate operation Suitable for a wide range of applications due to innovative integrated screw connector Indoor Outdoor Underground Water Installation ducts Ductwork Note Incl. Screw connectors min. Ø over conductor insulation after removal of outer semi-conducting layer Storage conditions/shelf life Unlimited shelf life Scope of delivery Spreader cap Thick wall heat-shrinkable outer tubing with hot melt adhesive Oil barrier tubing Heat-shrink tubing Silicone stress-control elements Earthing wire Copper braid tape Pressure spring Assembly accessories Sealing tape Stress control filling tape (blue) Fire protection wrap Screw connector for copper-wire screen Innovative screw connector with conductive sheath Assembly instructions Nominal cross section ² 12kV 17.5kV ) 6/10 (12)kV /15 (17.5)kV CHMPRSV3-1 17kV Cable accessories for paper-insulated cables 73

74 Transition joints Medium Voltage 2013 CHMPR 3-1 Transition joint from belted cable to polymeric cables CHMPR3-1 hybrid transition joints for transition to three single-core plasticinsulated cables are suitable for both paper-insulated lead cables and Hochsta dter cables up to 17.5 kv. Padding kits for paper-insulated cables are available for downwards enlargement of the operational area. Suitable for Compression connectors. Dimensions = ength Cable accessories for paper-insulated cables Reliable stress control due to flexible silicone stress control elements Wide conductor and cross-section range Wide cross-section range Quick, safe and easy assembly Ready for iediate operation min. Ø over conductor insulation after removal of outer semiconducting layer ) 6/10 (12)kV /15 (17.5)kV CHMPR3-1 17kV Indoor Outdoor Underground Water Installation ducts Ductwork Note Compression connectors not included Nominal cross section ² 12 kv 17.5 kv max. Ø of connector max. connector length Storage conditions/shelf life Unlimited shelf life Scope of delivery Spreader cap Thick wall heat-shrinkable outer tubing with hot melt adhesive Oil barrier tubing Heat-shrink tubing Silicone stress-control elements Earthing wire Copper braid tape Pressure spring Assembly accessories Sealing tape Stress control filling tape (blue) Fire protection wrap Assembly instructions Nominal cross section ² max. Ø of connector max. connector length Appropriate connectors must be ordered separately. Padding kits must be ordered separately. Padding kit PS(G+H)17/1 (197690) to be used with sur 35-50² (17.5kV) and 35-70² (12kV). 74

75 Transition joints CHMPR 3 Transition joint from belted cable to polymeric cables CHMPR3 hybrid transition joints for transition to three-core plastic-insulated cables are suitable for both paper-insulated lead cables and Hochsta dter cables up to 17.5 kv. Padding kits for paper-insulated cables are available for downwards enlargement of the operational area. Suitable for Compression connectors. Dimensions = ength Reliable stress control due to flexible silicone stress control elements Quick, safe and easy assembly Ready for iediate operation Wide cross-section range min. Ø over conductor insulation after removal of outer semiconducting layer ) 6/10 (12)kV /15 (17.5)kV CHMPR3 17kV Indoor Outdoor Underground Water Installation ducts Ductwork Note Compression connectors not included Nominal cross section ² 12 kv 17 kv max. Ø of connector max. connector length Storage conditions/shelf life Unlimited shelf life Scope of delivery Spreader cap Thick wall heat-shrinkable outer tubing with hot melt adhesive Oil barrier tubing Heat-shrink tubing Silicone stress-control elements Earthing wire Copper braid tape Pressure spring Assembly accessories Sealing tape Stress control filling tape (blue) Fire protection wrap Assembly instructions Nominal cross section ² max. Ø of connector max. connector length Appropriate compression connectors must be ordered separately. Padding kits must be ordered separately. Padding kit PS(G+H)17/1 (197690) tob e used with sur 35-50² (17.5kV and resp ² (12kV). Cable accessories for paper-insulated cables 75

76 Straight-through joints Medium Voltage 2013 CHMPPR3 Straight-through joint for belted cables up to 17.5 kv (MIND) CHMPPR3 hybrid transition joints are suitable for belted cables and Hochsta dter cables up to 17.5 kv. Suitable for compression connectors. Dimensions = ength Cable accessories for paper-insulated cables Quick, safe and easy assembly Ready for iediate operation Wide cross-section range min. Ø over conductor insulation after removal of outer semiconducting layer ) 6/10 (12)kV /15 (17.5)kV CHMPPR3 17kV Indoor Outdoor Underground Water Installation ducts Ductwork Note Compression connectors not included Nominal cross section ² 12 kv 17.5kV max. Ø of connector max. connector length Storage conditions/shelf life Unlimited shelf life Scope of delivery Spreader cap Thick wall heat-shrinkable outer tubing with hot melt adhesive Oil barrier tubing Heat-shrink tubing Earthing wire Copper braid tape Pressure spring Assembly accessories Sealing tape Stress control filling tape (blue) Fire protection wrap Assembly instructions Nominal cross section ² max. Ø of connector max. connector length Appropriate compression connectors must be ordered separately. 76

77 Terminations CHEP-3I Indoor termination for belted cables up to 17.5 kv (MIND) CHEP-3I indoor terminations are suitable for belted cables up to 17.5 kv for MIND cables only. For cables with draining compound please contact us. Dimensions = ength Wide cross-section range Quick, safe and easy assembly Ready for iediate operation Indoor Note Cable lugs not included Storage conditions/shelf life Unlimited shelf life Scope of delivery Tracking resistant spreader cap Tracking-resistant heat-shrink tubing Earthing kit Assembly accessories Sealing tape Assembly instructions Appropriate cable lugs must be ordered separately. min. Ø over conductor Nominal cross section ² 12 kv 17.5kV ) 6/10 (12)kV /15 (17.5)kV CHEP-3I 12kV Cable accessories for paper-insulated cables 77

78 Terminations Medium Voltage 2013 CHEP-3F Outdoor termination for belted cables up to 17.5 kv (MIND) CHEP-3F outdoor terminations are suitable for belted cables up to 17.5 kv for MIND cables only. For cables with draining compound please contact us. Dimensions = ength Ø S = Diameter of cable shed Wide cross-section range Quick, safe and easy assembly Ready for iediate operation Outdoor Note Cable lugs not included Storage conditions/shelf life Unlimited shelf life Scope of delivery Tracking resistant spreader cap Tracking-resistant heat-shrink tubing Silicone sheds Earthing kit Assembly accessories Sealing tape Assembly instructions Cable accessories for paper-insulated cables min. Ø over conductor Number of sheds per phase Ø S Nominal cross section ² 12 kv 17.5kV ) 6/10 (12)kV /15 (17.5)kV CHEP-3F 17kV Appropriate cable lugs must be ordered separately. 78

79 Transition joints CHMP(H) 3-1 Transition joint for H-cables to polymeric cables CHMP(H)3-1 hybrid transition joints for transition to three single-core plasticinsulated cables are suitable for Hochsta dter cables up 24 to 36 kv. Padding kits for paper-insulated cables are available for downwards enlargement of the operational area. Suitable for compression connectors. Dimensions = ength Reliable stress control due to flexible silicone stress control elements Wide conductor and cross-section range Wide cross-section range Quick, safe and easy assembly Ready for iediate operation Indoor Outdoor Underground Water Installation ducts Ductwork Note Compression connectors not included min. Ø over conductor insulation after removal of outer semi-conducting layer max. Ø of connector max. connector length Storage conditions/shelf life Unlimited shelf life Scope of delivery Spreader cap Thick wall heat-shrinkable outer tubing with hot melt adhesive Oil barrier tubing Heat-shrink tubing Silicone stress-control elements Earthing wire Copper braid tape Pressure spring Assembly accessories Sealing tape Stress control filling tape (blue) Fire protection wrap Assembly instructions Nominal cross section ² 24kV 36kV ) 12/20 (24)kV /22 (24)kV CHMP(H) kv ) 18/30 (36)kV - 19/33 (36)kV CHMP(H) kv Appropriate compression connectors must be ordered separately. Padding kits must be ordered separately. Padding kit PS(H)24/1 (197692) to be used with sur 35-70² (24kV) and 35-70² (24kV). Cable accessories for paper-insulated cables 79

80 Transition joints Medium Voltage 2013 CHMP(H) 3 Transition joint for H-cables to polymeric cables CHMP(H)3 hybrid transition joints for transition to three-core plastic-insulated cables are suitable for Hochsta dter cables up 24 to 36 kv. Padding kits for paper-insulated cables are available for downwards enlargement of the operational area. Suitable for compression connectors. Dimensions = ength Cable accessories for paper-insulated cables Reliable stress control due to flexible silicone stress control elements Quick, safe and easy assembly Ready for iediate operation Wide cross-section range Indoor Outdoor Underground Water Installation ducts Ductwork Note Compression connectors not included min. Ø over conductor insulation after removal of outer semi-conducting layer max. Ø of connector max. connector length Storage conditions/shelf life Unlimited shelf life Scope of delivery Spreader cap Thick wall heat-shrinkable outer tubing with hot melt adhesive Oil barrier tubing Heat-shrink tubing Silicone stress-control elements Earthing wire Copper braid tape Pressure spring Assembly accessories Sealing tape Stress control filling tape (blue) Fire protection wrap Assembly instructions Nominal cross section ² 24kV 36kV ) 12/20 (24)kV /22 (24)kV CHMP(H)3 24kV ) 18/30 (36)kV - 19/33 (36)kV CHMP(H)3 36kV Appropriate compression connectors must be ordered separately. Padding kits must be ordered separately. Padding kit PS(H)24/1 (197692) to be used with sur 35-70² (24kV) and 35-70² (24kV). 80

81 Straight-through joints CHMPP(H)3 Straight-through joint for H-cables from 24 up to 36 kv CHMPP(H)3 hybrid transition joints are suitable for Hochsta dter cables up to 24 to 36 kv. Padding kits for paper-insulated cables are available for downwards enlargement of the operational area. Suitable for compression connectors. Dimensions = ength Quick, safe and easy assembly Ready for iediate operation Wide cross-section range Indoor Outdoor Underground Water Installation ducts Ductwork Note Compression connectors not included min. Ø over conductor insulation after removal of outer semi-conducting layer Appropriate compression connectors must be ordered separately. max. Ø of connector max. connector length Storage conditions/shelf life Unlimited shelf life Scope of delivery Spreader cap Thick wall heat-shrinkable outer tubing with hot melt adhesive Oil barrier tubing Heat-shrink tubing Silicone stress-control elements Earthing wire Copper braid tape Pressure spring Assembly accessories Sealing tape Spacers Stress control filling tape (blue) Fire protection wrap Assembly instructions Nominal cross section ² 24kV 36kV ) 12/20 (24)kV /22 (24)kV CHMPP(H)3 24kV ) 18/30 (36)kV - 19/33 (36)kV CHMPP(H)3 36kV Cable accessories for paper-insulated cables 81

82 Terminations Medium Voltage 2013 CHEP(H)-3I Indoor termination for H-cables from 24 up to 36 kv CHEP(H)-3F outdoor terminations are suitable for Hoechstaedter cables from 24 up to 36 kv for MIND cables only. For cables with draining compound please contact us. Dimensions = ength Ø S = Diameter of cable shed Wide cross-section range Quick, safe and easy assembly Ready for iediate operation Indoor Note Cable lugs not included Storage conditions/shelf life Unlimited shelf life Scope of delivery Tracking-resistant heat-shrink tubing Conductive spreader cap Conductive heat-shrink tubing Oil barrier tubing Filling tape Silicone sheds Earthing wire Pressure spring Assembly instructions Cable accessories for paper-insulated cables min. Ø over conductor Number of sheds per phase Ø S Nominal cross section ² 24kV 36kV U0 ) 12/20 (24)kV /22 (24)kV CHEP(H)-3I 24kV ) 18/30 (36)kV - 19/33 (36)kV CHEP(H)-3I 36kV Appropriate cable lugs must be ordered separately. 82

83 Terminations CHEP(H)-3F Outdoor termination for H-cables from 24 up to 36 kv CHEP(H)-3F outdoor terminations are suitable for Hoechstaedter cables from 24 up to 36 kv for MIND cables only. For cables with draining compound please contact us. Dimensions = ength Ø S = Diameter of cable shed Wide cross-section range Quick, safe and easy assembly Ready for iediate operation Outdoor Note Cable lugs not included min. Ø over conductor Number of sheds per phase Ø S Storage conditions/shelf life Unlimited shelf life Scope of delivery Thick wall heat-shrinkable outer tubing with hot melt adhesive Tracking-resistant heat-shrink tubing Conductive spreader cap Oil barrier tubing Filling tape Silicone sheds Earthing wire Pressure spring Sealing tape Oil-barrier stress control filling tape (blue) Assembly instructions Nominal cross section ² 24kV 36kV ) 12/20 (24)kV /22 (24)kV CHEP(H)-3F 24kV ) 18/30 (36)kV - 19/33 (36)kV CHEP(H)-3F 36kV Appropriate cable lugs must be ordered separately. Cable accessories for paper-insulated cables 83

84 Transition joints Medium Voltage 2013 CHMP(3Pb) 3-1 Transition joint for 3-core single lead sheath cables to polymeric cables CHMP(3Pb)3-1 hybrid transition joints for transition to three single-core cables are suitable for all three-core lead sheath cables up to 36 kv. Padding kits for paper-insulated cables are available for downwards enlargement of the operational area. Suitable for compression connectors. Dimensions = ength Cable accessories for paper-insulated cables Reliable stress control due to flexible silicone stress control elements Wide conductor and cross-section range Wide cross-section range Quick, safe and easy assembly Ready for iediate operation min. Ø over conductor insulation after removal of outer semi-conducting layer ) 6/10 (12)kV /15 (17.5)kV CHMP(3Pb) kv Indoor Outdoor Underground Water Installation ducts Ductwork Note Compression connectors not included Nominal cross section ² 12 kv 17 kv max. Ø of connector max. connector length Scope of delivery Spreader cap Thick wall heat-shrinkable outer tubing with hot melt adhesive Oil barrier tubing Heat-shrink tubing Silicone stress-control elements Earthing wire Copper braid tape Pressure spring Assembly accessories Sealing tape Stress control filling tape (blue) Fire protection wrap Assembly instructions Nominal cross section ² max. Ø of connector max. connector length min. Ø over conductor insulation after removal of outer semi-conducting layer ) 12/20 (24)kV /22 (24)kV CHMP3Pb3-1 24kV max. Ø of connector max. connector length Nominal cross section ² Appropriate compression connectors must be ordered separately. Padding kits must be ordered separately. Padding kit PS(3Pb+Pb), (197699) to be used with sur 35-70² (24kV). Please use the padding kit PS(3Pb+Pb), (197701) for the following case: for sur 35-70² (36kV). Please use the padding kit PS(3Pb+Pb), (Art.Nr ) for the following case: for sur ² (36kV). 24kV 36kV ) 18/30 (36)kV - 19/33 (36)kV CHMP3Pb3-1 36kV

85 Transition joints CHMP(3Pb) 3 Transition joint for 3-core single lead sheath cables to polymeric cables CHMPP(3Pb)3 hybrid transition joints are suitable for all three-core lead sheath cables up to 36 kv. Padding kits for paper-insulated cables are available for downwards enlargement of the operational area. Suitable for compression connectors. Dimensions = ength Reliable stress control due to flexible silicone stress control elements Wide cross-section range Quick, safe and easy assembly Ready for iediate operation min. Ø over conductor insulation after removal of outer semi-conducting layer ) 6/10 (12)kV /15 (17.5)kV CHMP(3Pb)3 17kV Indoor Outdoor Underground Water Installation ducts Ductwork Note Compression connectors not included Storage conditions/shelf life Unlimited shelf life Nominal cross section ² 12 kv 17.5 kv max. Ø of connector max. connector length Scope of delivery Spreader cap Thick wall heat-shrinkable outer tubing with hot melt adhesive Oil barrier tubing Heat-shrink tubing Silicone stress-control elements Earthing wire Copper braid tape Pressure spring Assembly accessories Sealing tape Stress control filling tape (blue) Fire protection wrap Assembly instructions Nominal cross section ² max. Ø of connector max. connector length min. Ø over conductor insulation after removal of outer semi-conducting layer ) 12/20 (24)kV /22 (24)kV CHMP(3Pb)3 24kV max. Ø of connector max. connector length Nominal cross section ² Appropriate compression connectors must be ordered separately. Padding kits must be ordered separately. Padding kit PS(3Pb+Pb), (197699) to be used with sur 35-70² (24kV). Please use the padding kit PS(3Pb+Pb), (197701) for the following case: for sur 35-70² (36kV). Please use the padding kit PS(3Pb+Pb), (Art.Nr ) for the following case: for sur ² (36kV). 24kV 36kV ) 18/30 (36)kV - 19/33 (36)kV CHMP(3Pb)3 36kV Cable accessories for paper-insulated cables 85

86 Straight-through joints Medium Voltage 2013 CHMPP(3Pb)3 Straight-through joint for 3-core single lead sheath cables CHMPP(3Pb)3 hybrid transition joints are suitable for all three-core lead sheath cables up to 36 kv. Suitable for compression connectors. Dimensions = ength Cable accessories for paper-insulated cables Quick, safe and easy assembly Ready for iediate operation Wide cross-section range min. Ø over conductor ) 6/10 (12)kV /15 (17.5)kV CHMPP(3Pb)3 12kV Indoor Outdoor Underground Water Installation ducts Ductwork Note Compression connectors not included Nominal cross section ² 12 kv 17.5 kv max. Ø of connector max. connector length Storage conditions/shelf life Unlimited shelf life Scope of delivery Spreader cap Thick wall heat-shrinkable outer tubing with hot melt adhesive Oil barrier tubing Heat-shrink tubing Silicone stress-control elements Earthing wire Copper braid tape Pressure spring Assembly accessories Sealing tape Stress control filling tape (blue) Fire protection wrap Assembly instructions Nominal cross section ² max. Ø of connector max. connector length min. Ø over conductor ) 12/20 (24)kV /22 (24)kV CHMPP(3Pb)3 24kV max. Ø of connector Appropriate compression connector must be ordered separately. max. connector length Nominal cross section ² 24kV 36kV ) 18/30 (36)kV - 19/33 (36)kV CHMPP(3Pb)3 36kV

87 Terminations CHEP(3Pb)-3I Indoor termination for 3-core single lead sheath cables CHEP(3Pb)-3I indoor terminations are suitable for three-core single lead sheath cables from 24 up to 36 kv for MIND cables only. For cables with draining compound please contact us. Dimensions = ength Ø S = Diameter of cable shed Combination of slip-on and heat-shrink components Wide cross-section range Quick, safe and easy assembly Ready for iediate operation Indoor Note Cable lugs not included Storage conditions/shelf life Unlimited shelf life Scope of delivery Tracking-resistant heat-shrink tubing Oil barrier tubing Silicone sheds Sealing tape Oil-barrier stress control filling tape (blue) Earthing wire Pressure spring Assembly instructions min. Ø over conductor Number of sheds per phase Ø S Nominal cross section ² 24kV 36kV ) 12/20 (24)kV /22 (24)kV CHEP(3Pb)-3I 24kV ) 18/30 (36)kV - 19/33 (36)kV CHEP(3Pb)-3I 36kV Appropriate cable lugs must be ordered separately. Cable accessories for paper-insulated cables 87

88 Terminations Medium Voltage 2013 CHEP(3Pb)-3F Outdoor termination for 3-core single lead sheath cables CHEP(3Pb)-3F outdoor terminations are suitable for three-core single lead sheath cables from 24 up to 36 kv for MIND cables only. For cables with draining compound please contact us. Dimensions = ength Ø S = Diameter of cable shed Combination of slip-on and heat-shrink components Wide cross-section range Quick, safe and easy assembly Ready for iediate operation Outdoor Note Cable lugs not included Storage conditions/shelf life Unlimited shelf life Scope of delivery Weatherproof spreader cap Tracking-resistant heat-shrink tubing Oil barrier tubing Silicone sheds Sealing tape Oil-barrier stress control filling tape (blue) Earthing wire Pressure spring Assembly instructions Cable accessories for paper-insulated cables min. Ø over conductor Number of sheds per phase Ø S Nominal cross section ² 24kV 36kV ) 12/20 (24)kV /22 (24)kV CHEP(3Pb)-3F 24kV ) 18/30 (36)kV - 19/33 (36)kV CHEP(3Pb)-3F 36kV Appropriate cable lugs must be ordered separately. 88

89 Terminations Cable accessories for paper-insulated cables 89

90 Complete safety 90

91 Medium Voltage 2013 Page Straight-through joints for single-core cables 92 Straight-through joints for 3-core cables 93 Terminations for single-core cables 94 Terminations for 3-core cables 96 Accessories 98 Cable accessories for screened cables according to British Standard 91

92 Straight-through joints for single-core cables Medium Voltage 2013 CHM(BS) Single-core straight-through joint for all polymeric single-core cables CHM (BS) straight-through joints are suitable for all single-core plasticinsulated cables (PVC, PE, XPE, EPR). They allow the connection of cables with different cross sections, conductive materials, semi-conducting layers (graphite-coated, removable or strippable) and screening (copper wire or tape). Suitable for compression connectors. Dimensions = ength Cable accessories for screened cables according to British Standard Reliable stress control due to flexible silicone stress control elements Quick, safe and easy assembly Ready for iediate operation Wide cross-section range Indoor Outdoor Underground Water Installation ducts Ductwork Note Compression connectors not included Joints with a range of U m = 12 kv must be used for cables of U m = 7.2 kv. (Check minimum diameter over conductor insulation). Storage conditions/shelf life Unlimited shelf life Scope of delivery Thick wall heat-shrinkable insulation tubing Thick wall heat-shrinkable outer tubing with hot melt adhesive Silicone stress-control elements Copper braid tube Pressure springs Assembly accessories Steel cage Stress control filling tape (blue) Assembly instructions min. Ø over conductor insulation after removal of outer semi-conducting layer max. Ø of connector max. connector length Nominal cross section ² ) 6/10 (12)kV /11 (12)kV CHM(BS) 12kV ) 18/30 (36)kV - 19/33 (36)kV CHM(BS) 36kV Appropriate compression connectors must be ordered separately. 12kV 36kV 92

93 Straight-through joints for 3-core cables CHM3(BS) Three-core straight-through joint for all 3-core polymeric cables CHM3(BS) straight-through joints are suitable for all three-core plastic-insulated cables (PVC, PE, XPE, EPR). They allow the connection of cables with different cross sections, conductive materials, semi-conducting layers (graphite-coated, removable or strippable) and screening (copper wire or tape). Suitable for compression connectors. Dimensions = ength Reliable stress control due to flexible silicone stress control elements For all cables with copper wire or tape screen Quick, safe and easy assembly Ready for iediate operation Wide cross-section range Indoor Outdoor Underground Water Installation ducts Ductwork Note Compression connectors not included Joints with a range of U m = 12 kv must be used for cables of U m = 7.2 kv. (Check minimum diameter over conductor insulation). Storage conditions/shelf life Unlimited shelf life Scope of delivery Thick wall heat-shrinkable insulation tubing Thick wall heat-shrinkable outer tubing with hot melt adhesive Silicone stress-control element Copper braid tube Pressure springs Stress control filling tape (blue) Assembly instructions Steel cage Assembly accessories Cable accessories for screened cables according to British Standard min. Ø over conductor insulation after removal of outer semiconducting layer U0/U (Um) 6/10 (12)kV /11 (12)kV CHM3(BS) 12kV max. Ø of connector max. connector length Nominal cross section ² 12kV 17.5kV 24kV 36kV U0/U (Um) 8.7/15 (17.5)kV CHM3(BS) 17kV U0/U (Um) 12/20 (24)kV /22 (24)kV CHM3(BS) 24kV U0/U (Um) 18/30 (36)kV - 19/33 (36)kV CHM3(BS) kV Appropriate compression connectors must be ordered separately. 93

94 Terminations for single-core cables Medium Voltage 2013 CHE-I (BS) Single-core indoor termination for all polymeric single-core cables CHE-I(BS) terminations are suitable for all single-core plastic-insulated cables (PVC, PE, XPE, EPR) with different types of semi-conducting layers (graphite-coated or strippable) and screening (copper wire or tape). Dimensions Cable accessories for screened cables according to British Standard Flexible silicone stress control elements ensure reliable stress control under all operating conditions Combination of slip-on and heat-shrink components Compatible with all cable lugs Wide cross-section range Quick, safe and easy assembly Ready for iediate operation Indoor Note Cable lugs not included 12 kv terminations must be used for 7.2 kv cables (Check minimum diameter over conductor insulation). = ength Ø S = Diameter of cable shed Storage conditions/shelf life Unlimited shelf life Scope of delivery 1 Set for 3 phases Tracking-resistant heat-shrink tubing Silicone stress-control elements Silicone sheds Earthing kit Sealing tape Assembly instructions min. Ø over conductor insulation after removal of outer semi-conducting layer Number of sheds per phase Ø S Nominal cross section ² 12kV 36kV ) 6/10 (12)kV /11 (12)kV CHE-I(BS) 12kV ) 18/30 (36)kV - 19/33 (36)kV CHE-I(BS) 36kV Appropriate cable lugs must be ordered separately. 94

95 Terminations for single-core cables CHE-F(BS) Single-core outdoor termination for all polymeric single-core cables CHE-F(BS) terminations are suitable for all single-core plastic-insulated cables (PVC, PE, XPE, EPR) with different types of semi-conducting layers (graphite-coated or strippable) and screening (copper wire or tape). Dimensions Flexible silicone stress control elements ensure reliable stress control under all operating conditions Combination of slip-on and heat-shrink components Wide cross-section range Quick, safe and easy assembly Ready for iediate operation Outdoor Note Cable lugs not included 12 kv terminations must be used for 7.2 kv cables (Check minimum diameter over conductor insulation). = ength Ø S = Diameter of cable shed Storage conditions/shelf life Unlimited shelf life Scope of delivery 1 Set for 3 phases Tracking-resistant heat-shrink tubing Silicone stress-control elements Silicone sheds Earthing kit Sealing tape Assembly instructions Cable accessories for screened cables according to British Standard min. Ø over conductor insulation after removal of outer semi-conducting layer Number of sheds per phase Ø S Nominal cross section ² 12kV 36kV ) 6/10 (12)kV /11 (12)kV CHE-F(BS) 12kV ) 18/30 (36)kV - 19/33 (36)kV CHE-F(BS) 36kV Appropriate cable lugs must be ordered separately. 95

96 Terminations for 3-core cables Medium Voltage 2013 CHE-3I(BS) Three-core indoor termination for all 3-core polymeric cables CHE-3I(BS) terminations are suitable for all three-core plastic-insulated cables (PVC, PE, XPE, EPR) with different types of semi-conducting layers (graphite-coated or strippable) and screening (copper wire or tape). Dimensions Cable accessories for screened cables according to British Standard Flexible silicone stress control elements ensure reliable stress control under all operating conditions Combination of slip-on and heat-shrink components Wide cross-section range Quick, safe and easy assembly Ready for iediate operation Indoor Note Cable lugs not included 12 kv terminations must be used for 7.2 kv cables (Check minimum diameter over conductor insulation). Each unit contains materials for one set of three terminations. = ength Ø S = Diameter of cable shed Storage conditions/shelf life Unlimited shelf life Scope of delivery Tracking-resistant heat-shrink tubing Silicone stress-control elements Silicone sheds Earthing kit Sealing tape Tracking resistant spreader cap Assembly instructions min. Ø over conductor insulation after removal of outer semi-conducting layer Number of sheds per phase Ø S Nominal cross section ² 12kV 17.5kV 36kV ) 6/10 (12)kV /11 (12)kV CHE-3I(BS) 12kV ) 8.7/15 (17.5)kV CHE-3I(BS) 17kV ) 18/30 (36)kV - 19/33 (36)kV CHE-3I(BS) 36kV Appropriate cable lugs must be ordered separately. 96

97 Terminations for 3-core cables CHE-3F(BS) Three-core outdoor termination for all 3-core polymeric cables CHE-3F(BS) terminations are suitable for all three-core plastic-insulated cables (PVC, PE, XPE, EPR) with different types of semi-conducting layers (graphite-coated or strippable) and screening (copper wire or tape). Dimensions Flexible silicone stress control elements ensure reliable stress control under all operating conditions Combination of slip-on and heat-shrink components Wide cross-section range Quick, safe and easy assembly Ready for iediate operation Outdoor Note Cable lugs not included 12 kv terminations must be used for 7.2 kv cables (Check minimum diameter over conductor insulation). = ength Ø S = Diameter of cable shed Storage conditions/shelf life Unlimited shelf life Scope of delivery Tracking-resistant heat-shrink tubing Silicone stress-control elements Silicone sheds Earthing kit Sealing tape Tracking resistant spreader cap Assembly instructions Cable accessories for screened cables according to British Standard min. Ø over conductor insulation after removal of outer semi-conducting layer Number of sheds per phase Ø S Nominal cross section ² 12kV 17.5kV 36kV ) 6/10 (12)kV /11 (12)kV CHE-3F(BS) 12kV ) 8.7/15 (17.5)kV CHE-3F(BS) 17kV ) 18/30 (36)kV - 19/33 (36)kV CHE-3F(BS) 36kV Appropriate cable lugs must be ordered separately. 97

98 Accessories Medium Voltage 2013 AUF(BS) Armour continuity for three-core joints Armour continuity for armoured three-core polymeric cables in accordance with British Standard. Dimensions = ength Cable accessories for screened cables according to British Standard Quick, safe and easy assembly Superior electrical properties High mechanical strength Earthing continuity and earth contactor For cast resin, heat-shrink and slip-on cable accessories Enables solder-free electrical connection of metal cable components (screen, armouring, metal sheath). Storage conditions/shelf life Unlimited shelf life Scope of delivery Hose clamp Steel cage Cloth tape Backup-ring Internal-Ø Nominal cross section ² 7.2 kv 12 kv 17.5 kv 24 kv 36 kv AUF 1100/ / / / /

99 Accessories EGA(BS) Earthing accessories for cables with tape screen and/or armouring for terminations EGA(BS) earthing kit for three-core polymeric cables in accordance with British Standard. Quick, safe and easy assembly Superior electrical properties High mechanical strength Suitable for indoor and outdoor use Earth connection and contactor For cast resin, heat-shrink and slip-on cable accessories Enables solder-free electrical connection of metal cable components (screen, armouring, metal sheath). Note Incl. cable lug Storage conditions/shelf life Unlimited shelf life Scope of delivery Heat-shrink tube Earthing wire Earthing accessories Pressure springs Hose clamp Backup-ring Cable accessories for screened cables according to British Standard EGA3BS Internal-Ø Nominal cross section Copper braid ² Nominal cross section ² 7.2 kv 12 kv 17.5 kv 24 kv 36 kv (53) (68) (73) (87) (97) (107)

100 Accessories Medium Voltage 2013 CG Cable entry points for XPE- and paper-insulated cables Cable entry point for junction boxes for transformers and substations. Dimensions CG A CG B Cable accessories for screened cables according to British Standard Scope of delivery Heat-shrink tube 1 Cable entry point Assembly accessories Assembly instructions Ø ² under armouring paper-insulated cable under armouring of XPE-cable CGA CGB

101 Accessories Cable accessories for screened cables according to British Standard 101

102 Medium Voltage 2013 Customised solutions 102

103 Cable accessories for the industries Page Cable accessories for industries

104 Cable accessories for shipyard-industrie Medium Voltage 2013 Cellpack s product portfolio also includes special solutions for the oil and gas, mining and shipbuilding industries as well as for offshore applications.these cable accessories are exposed to rain, salt, chemicals and extreme mechanical loads. The products especially designed for these applications comply with current international norms such as IEC and Cenelec, and with industry specific accreditation requirements. More specific information is available on request. Cable accessories for the shipbuilding industry 104

105 Cable accessories for shipyard-industrie Cable accessories for the shipbuilding industry 105

106 Medium Voltage

107 Medium Voltage 2013 We won t leave you in the lurch! Page Heat-shrink tubing 106 Compression cable lugs and Compression connectors complying with DIN 112 Screw cable lugs 119 Earthing components 120 Tapes 123 Tools 127 Chemical products 131 Accessories 107

108 Heat-shrink tubing Medium Voltage 2013 SRBB Heat-shrink tubing up to 36kV protection for busbar systems and reduction of minimum clearance Medium-walled Stabilized against UV rays Halogen-free Tracking resistant Non-corrosive Resistant to bacteria and fungi Allows for clearance reduction between busbars in medium voltage substations up to 36kV. Corrosion protection Colour(s) red brown Material Cross-linked polyolefin SRBB Recoended application range round Ø Recoended application range Width (B) + Height (H) rectangular min. max. min. max Accessories Typ SRBB SRBB Internal-Ø Recovered Packing unit wall thickness m before shrinkage after shrinkage piece x m x x x x x x 30 (Roll) x 30 (Roll) x 30 (Roll) x 30 (Roll) x 30 (Roll)

109 Heat-shrink tubing Technical Data Value Test Physical properties Density 1.22 g/cm³ IEC Hardness 89 Shore A DIN Elongation at break 500 % IEC Tensile strength at break 16 N/² IEC ongitudinal shrinkage +5 % / -10 % IEC Shrink ratio 3:1 IEC Concentricity expanded Concentricity recovered 50 % 85 % IEC Thermal properties Operating temperature range -40 C up to 120 C IEC Shrinkage temperature > 125 C CP-PM-1004* Burning behaviour not self-extinguishing IEC mode C Flexibility at low temperatures -40 C IEC Electrical properties Dielectric strength 20 kv/ IEC Volume resistivity Ω x cm IEC Chemical properties Corrosion none IEC Water absorption < 0.15 % IEC Resistance to fungus and decay Ra. 1 IEC Minimum allowance between the busbars: 12kV 17.5kV Busbar (round shaped) without isolation Ph/Ph and Ph/E with isolation Ph/Ph with isolation Ph/E Busbar (rectangular shaped) without isolation Ph/Ph and Ph/E with isolation Ph/Ph with isolation Ph/E kV 36kV Accessories 109

110 Heat-shrink tubing Medium Voltage 2013 SRAT Thick wall heat-shrink tubing Shrinkage ratio 3:1 Thick-walled Stabilized against UV rays Halogen-free Non-corrosive Infusible Highly resistant to electrical breakdown Tracking resistance in compliance with IEC 112 High tensile strength Resistant to cold flow (thermally stable) Insulation tube for conductors in terminations of 3.6 to 42 kv Corrosion protection Colour(s) red brown Material Cross-linked polyolefin Free of lead and cadmium Accessories m before shrinkage Internal-Ø after shrinkage Recovered wall thickness Packing unit piece x m in 1m sections x x x SRAT x x x x on rolls x 30 (Roll) x 30 (Roll) SRAT x 30 (Roll) x 30 (Roll) x 30 (Roll) x 30 (Roll)

111 Heat-shrink tubing Technical Data Value Test Physical properties Density 1.30 g/cm³ DIN Hardness 50 Shore D DIN Elongation at break 350 % DIN IEC 15C/590/CD Tensile strength at break 13 N/² DIN IEC 15C/590/CD ongitudinal shrinkage +5% / -15% DIN IEC 15C/590/CD Shrink ratio > 3:1 DIN IEC 15C/590/CD Concentricity expanded Concentricity recovered 50 % 85 % DIN IEC 15C/590/CD Thermal properties Operating temperature range -40 C up to 120 C DIN IEC 15C/590/CD Shrinkage temperature > 125 C CP-PM-1004* Burning behaviour not self-extinguishing DIN VDE 0304 Flexibility at low temperatures -40 C DIN IEC 15C590/CD Effect of thermal ageing (168h at 150 C) on elongation at break 300 % Electrical properties Dielectric strength 16 kv/ DIN VDE 0303 Part 2 Chemical properties Water absorption < 0.15 % Resistance to fungus and decay Ra. 1 DIN IEC 15C/590/CD Accessories 111

112 Compression cable lugs and Compression connectors complying with DIN Medium Voltage 2013 DV-CU-V Cu compression connector complies with DIN 46267, without separator Strain relief connector (hexagonally compressed) for copper conductor, suitable for joints. Dimensions D = ength D = Centric bore hole Q = Cross section K = Die code no.~outer diameter For RM/SM copper conductors complying with DIN VDE 0295 Material Copper tin-plated Accessories DV-CU-V To be used with suitable compression tool with DIN dies. Fixed price no metal surcharge D Q ² K

113 Compression cable lugs and Compression connectors complying with DIN DVZ-CU-V-D Cu compression connector complies with DIN 46267, with separator Strain relief connector (hexagonally compressed) with separator for copper conductor, suitable for joints. Dimensions D = ength D = Centric bore hole Q = Cross section K = Die code no.~outer diameter Especially for transition sleeves and pot end joints For RM/SM copper conductors complying with DIN VDE 0295 Material Copper tin-plated m D Q ² DVZ-CU-V-D To be used with suitable compression tool with DIN dies. Fixed price no metal surcharge K Accessories 113

114 Compression cable lugs and Compression connectors complying with DIN Medium Voltage 2013 DV-A Al Compression connector complies with DIN 46267, without separator Strain relief connector (hexagonally compressed) without separator for aluminium conductor, suitable for joints. Dimensions D RM/SM, SE and RE aluminium conductors complying with DIN VDE 0295 Note *does not comply with DIN Standards = ength D = Centric bore hole Q = Cross section RM = Multi-core stranded round SM = Multi-core stranded sector shaped SE = Sector shaped solid RE = Round solid K = Die code no.~outer diameter Material Blank aluminium Accessories D Q ² K RM/SM SE RE 16* DV-A To be used with suitable compression tool with DIN dies. Fixed price no metal surcharge 114

115 Compression cable lugs and Compression connectors complying with DIN DVZ-A-D Al Compression connector complies with DIN 46267, with separator Strain relief connector (hexagonally compressed) with separator for aluminium conductor. Dimensions D RM/SM, SE and RE aluminium conductors complying with DIN VDE 0295 Especially for transition sleeves and pot end joints = ength D = Centric bore hole Q = Cross section RM = Multi-core stranded round SM = Multi-core stranded sector shaped SE = Sector shaped solid K = Die code no.~outer diameter Material Blank aluminium D RM/SM Q ² K SE DVZ-A-D To be used with suitable compression tool with DIN dies. Fixed price no metal surcharge Accessories 115

116 Compression cable lugs and Compression connectors complying with DIN Medium Voltage 2013 DK-CU-V Cu compression cable lug complies with DIN Cable lugs (hexagonally compressed) for copper conductors, suitable for indoor terminations. Dimensions D D1 B = ength B = Width D = Centric bore hole D1 = Flat hole diameter Q = Cross section K = Die code no.~outer diameter Cable lugs for RM/SM copper conductors complying with DIN VDE 0295 Note *does not comply with DIN Standards Material Copper tin-plated Test standard DIN 46235, Cable lugs for compression connections (lug mould for copper conductor) Accessories B 6/ /8* / /12* / / / / / / / / / DK-CU-V 95/ / / / / / / / / /14* / / /16* /16* / To be used with suitable compression tool with DIN dies. Fixed price no metal surcharge D D1 Q ² K 116

117 Compression cable lugs and Compression connectors complying with DIN DK-CU-V-D Cu compression cable lug complies with DIN 46235, blocked Cable lugs Cu (hexagonal compression type) for copper conductors, designed for outdoor terminations. Dimensions D D1 B Cable lugs for RM/SM copper conductors complying with DIN VDE 0295 Note *does not comply with DIN Standards = ength B = Width D = Centric bore hole D1 = Flat hole diameter Q = Cross section K = Die code no.~outer diameter Material Copper tin-plated Test standard DIN 46235, Cable lugs for compression connections (lug mould for copper conductor) DK-CU-V-D B To be used with suitable compression tool with DIN dies. Fixed price no metal surcharge D D1 Q ² K 16/12* / / / / / / / / / / / /16* Accessories 117

118 Compression cable lugs and Compression connectors complying with DIN Medium Voltage 2013 DK-A-D Al compression cable lug complies with DIN 46329, blocked Cable lugs (hexagonally compressed) for aluminium conductors, suitable for indoor and outdoor terminations. Dimensions D D1 B Note *does not comply with DIN Standards = ength B = Width D = Centric bore hole D1 = Flat hole diameter Q = Cross section RM = Multi-core stranded round SM = Multi-core stranded sector shaped SE = Sector shaped solid RE = Round solid K = Die code no.~outer diameter Material Blank aluminium Test standard DIN 46329, Cable lugs for compression connections (circular mould for aluminium conductor) Accessories DK-A-D B To be used with suitable compression tool with DIN dies. Fixed price no metal surcharge D D1 Q ² RM/SM RE SE K 16/10* / / / / / / / /16* / / / / / / / / / /

119 Screw cable lugs CSK Screw cable lugs for Cu and AI blocked, aluminium tin-plated with shear bolts Screw cable lugs for RM, RE, SM, and SE aluminium and copper conductors, suitable for indoor and outdoor terminations. Dimensions Note *CSK : RM/RE cross section from 240 to 400 ², SM/SE cross section from 240 to 300². Cellpack counter bracket recoended for installation. = ength 1 = Centric bore hole D = Outer diameter D1 = Flat hole diameter D2 = Bore hole diameter Q = Cross section S = Number of bolts Material Aluminium, tin-plated Test standard EN D CSK * Other screw connectors available to order. Fixed price no metal surcharge D1 D2 Q ² S Accessories 119

120 Earthing components Medium Voltage 2013 EGA Earthing accessories for cables with tape screen and/or armouring for terminations EGA earthing kits for terminations for single-core cables with copper braid or aluminium screen (Fig. 1), and for unarmoured three-core cables (Fig. 3). Kit components: 3 flat-rolled copper wires and 3 pressure springs Dimensions 1 2 Quick, safe and easy assembly Superior electrical properties High mechanical strength Suitable for indoor and outdoor use Earthing continuity and earth contactor For cast resin, heat-shrink and slip-on cable accessories Enables solder-free electrical connection of metal cable components (screen, armouring, metal sheath). Note 1) Single core cables with copper tape or aluminium screens, non armoured. 2) Single core cables with copper tape or aluminium screens, armoured: Please order extra pressure spring ZR1. 3) Three core cables with copper tape or aluminium screens, non armoured. 4) Three core cables with copper tape or aluminium screens, armoured: Please order extra pressure spring ZR2. Scope of delivery Copper wire Pressure spring 3 4 S = external semi-conducting layer BS = Cu-Tape screen KM = Cable sheath RF = RF pressure spring ES = Cu-Earthing wire, flat tin-plated AR = Armouring ZR = Additional type RF pressure spring Accessories EGA Pressure spring Copper braid Ø of hole Nominal cross section ² For armoured cables, please order the pressure springs separately. Nominal cross section ² 7.2 kv 12 kv 17.5 kv 24 kv 36 kv ZR1 ZR RF RF 3 RF RF RF 4 RF RF RF 4 RF RF RF 5 RF RF RF 5 RF RF RF

121 Earthing components AUF Armour continuity for three-core joints Armour continuity kit for armoured three-core polymeric cables. Dimensions = ength 1. Pressure spring 2. Copper wire 3. Pressure spring Quick, safe and easy assembly Superior electrical properties High mechanical strength Earthing continuity and earth contactor For cast resin, heat-shrink and slip-on cable accessories Enables solder-free electrical connection of metal cable components (screen, armouring, metal sheath). Scope of delivery Copper wire Pressure springs Pressure spring Nominal cross section ² Copper braid 7.2kV 12kV 17.5kV 24kV 36kV AUF RF AUF RF For armoured cables, please order the pressure springs separately. Accessories 121

122 Earthing components Medium Voltage 2013 RF Pressure spring Corrosion-resistant Fatigue-proof Guarantees consistent radial contact stress For cast resin, heat-shrink and slip-on cable accessories Enables solder-free electrical connection of metal cable components (screen, armouring, metal sheath) and earthing materials (copper grounding wire, cooper mesh sleeve) Colour(s) brass Material Special stainless steel Accessories Width Pressure springs are no current-carrying parts. External-Ø Cable-Ø RF RF RF RF RF

123 Tapes No. 60, No. 62 High-voltage insulation tape self-amalgamating, pliable Easy application Fuses to form a homogeneous, cavity-free compound within a short space of time. Fully removable Durable Ozone-resistant No electrolytic corrosion Non tacky Extremely ductile Superior electrical properties Excellent adherence to a wide range of substances Superior physical properties Weatherproof Sealing of casting moulds Padding of cable insulation Conductor insulation for plastic-insulated cables up to 69 kv Repairing and connection of various insulating and cable materials e.g. PE, XPE, EPR, PVC, butyl, neoprene Colour(s) black Material EPR-Base ength m Width Thickness No No Accessories Technical Data Value Elongation at break 900 % Tensile strength at break 3 N/² Dielectric constant 2.8 Dissipation factor (50Hz) Dielectric strength 42 kv/ Volume resistivity Ω x cm Temperature range -40 C up to 100 C Water absorption 0.05 % 123

124 Tapes Medium Voltage 2013 No. 61 Conductive tape highly elastic, self-amalgamating Printed CAUTION-CONDUCTING TAPE to eliminate danger of confusion Fuses to form a homogeneous, cavity-free compound within a short space of time. Durable Ozone-resistant No electrolytic corrosion Self-fusing Highly flexible Superior physical properties Repairing of semi-conducting layer in medium voltage cables Electrical field smoothing For smoothing rough surfaces of connectors and cable lugs Colour(s) black Material EPR-Base Accessories No. 61 ength m Width Thickness Technical Data Value Elongation at break 900 % Tensile strength at break 3 N/² Volume resistivity 10 Ω x cm Temperature range -40 C up to 100 C 124

125 Tapes No. 63 Copper braid tape tinned Wrinkle-free application to all contours High flexibility Break-proof Earthing continuity and earth contactor Electrostatic shielding continuity Semi-conducting continuity for connectors Voltage grading continuity Colour(s) silver Material Braided tinned copper wires No. 63 ength m Width Thickness 25 x 9.1m x 5m x 10m x 5m Accessories 125

126 Tapes Medium Voltage 2013 No. 72 Repair tape Self-fusing 100% waterproof Superior electrical properties High tensile strength Repairing of damaged sheaths of all plastic- and rubber-insulated cables and conductors Note The use of a repair joint such as MZ is mandatory in case of damage extending beyond the cable sheath to the core insulation, screen or armour. Colour(s) black ength m Width Thickness No Accessories 126

127 Tools CPB Heat-shrink torch kit User-friendly rotating tube connector Gas supply shuts off automatically if burner head not installed Minimal risk of overheating Flame extinguished iediately upon releasing push button Continuously adjustable flame Bayonet fitting facilitates substitution of burner head Quick-starting piezo ignition Suitable for thick wall adhesive-lined heat-shrink tubing Shrinking of heat-shrinkable polyolefin products using flame or hot air on pre-extruded compound Caution note Warning: liquid gas is heavier than air. Adhere strictly to safety instructions provided with heat-shrink torch kit. Scope of delivery Wooden case with aluminium profile Handle Angulated hot-air torch Angulated heat-shrink torch Angulated needle point burner 3 x R 3 pressure control device, 8 li Anti-rupture device for tubing Gas tube Open-end spanner SW 17/19 Small gas bottle (0.4l content), incl. tube connection valve and suspension hook (CPB6) Refill connector for a small gas bottle (CPB6) 3 x DIN Kombi pressure control device (CPB5 8 li) ength m Content ml CPB 5 (Set) * CPB 6 (Set) * Handle CPB 5/6 with piezo ignition Needle point burner Heat-shrink torch Hot-air torch Gas tube HD 4.4 R 3/8 H x R 3/8 H Anti-rupture device for tubing R 3/8 x 3/8 H Pressure balance R 3/8 x 3/8 H Pressure balance DIN/Kombi 21,8-14 H x R 3/8 H Refill connector, DIN Kombi Small gas bottle, refillable Delivered in an aluminium side-faced wooden case. Components can also be ordered separately. Accessories 127

128 Tools Medium Voltage 2013 Clamp tool Assembly guide for CSV screw connectors and CSK screw cable lugs Assembly guide for CSV screw connectors and CSK screw cable lug with a diameter Scope of delivery Clamp tool Tool for diameter reduction Clamp tool CSV/CSK Accessories 128

129 Tools CP-FM20 Multi tool The CP-FM20 is designed for the cutting and stripping of outer cable sheaths and conductor insulation, in addition to cold-strippable semi-conducting layers. Suitable for cables with a diameter of For cold-strippable conducting layer. 0.3/0.4 or 0.7/0.8 according to thickness of material Adjustable stop and limiting bar Cut depth of the insulation and external sheath up to 10 Suitable for PVC/PE/XPE insulation Adjustable feed motion Cutting and stripping of outer sheath Controlled initial cutting of cold-strippable semi-conducting layer Cutting and stripping of conductor insulation Scope of delivery Allen key Carrying case CP-FM20 Multi-tool CP-FM 20-S1 (for cable sheath) Replacement cutter CP-FM 20-S2 (for semiconductor-layer) Multitool CP-FM Accessories 129

130 Tools Medium Voltage 2013 CP-P20 Peeling tool For removal of the co-extruded semi-conducting layer of medium voltage cables. Minimum strip length ca.30 Stripping depth adjustable from 0-1,2 in 0,1 steps Maintains high quality of stripped surface Hard metal peeling knife Operating range Predefined rounded corners Begin stripping at cable end Automatic working feed Cutting and stripping of solid extruded semi-conducting layer. Accessories ength Width Height Case assembly Peeling tool CP-P

131 Chemical products UNIVERSA CEANER 121 Detergent For use with Neoprene, Polyethylene, EPR, XPE, PVC; Butyl rubber and thermoplastic insulation Protection against accidental discharge Cleans and degreases without leaving residue. Non-conductive Fast-acting, safe No degradation Cleaning of semi-conducting layers Removal of semi-conductive residues (such as graphite) Cleaning and degreasing of motors and electrical equipment Cleaning of cables and conductors Note Clean all parts thoroughly. Air dry or wipe with a cloth. Repeat operation as required. Always test a small area prior to cleaning plastics or finished surfaces. Colour(s) clear Universal Cleaner Content l No No No No No Accessories Technical Data Value Density 0.62 g/cm 3 Vapour pressure (at 20 C) 200 hpa Flash point -19 C Ignition temperature 260 C ower explosion limit (Vol.-%) 1.1 Upper explosion limit Vol.-%

132 Chemical products Medium Voltage 2013 ZINC SPRAY 171 Anti-corrosion spray Zinc spray No. 171 binds to steel and iron surfaces using an electrochemical application to build a flexible protection film. This gives the parts an active cathodic corrosion protection. Smooth, fine porous film With hydrocarbon propellant (flaable) Varnishable Can be spot-welded Dries quickly Unmarked in compliance with ARB material regulations No hazard rating, in compliance with VBF Weatherproof Electrically conductive Frost-resistant ong-lasting corrosion protection Repairing of damaged zinc layer Repairing of galvanised surfaces Substitute for red lead primer Primer for use in auto repair Sealing of cavities Cold galvanising Oxidation protection Rust prevention Underground protection Colour(s) grey Accessories Content l Zinc spray No Zinc spray No. 171 is not approved according to the the food regulations and the construction material norms release 8/76 from the Institute for Construction Technology. Technical Data Value Density 0.95 g/cm 3 Degree of zinc purity 99 % 132

133 Chemical products INDUSTRIE 3-36 Protective agent Forms a clear, transparent film ubricates and permeates Dissolves rust Corrosion protection Protection of ferrous and non-ferrous metals during storage, processing, and transport Release of tightly-sealed components Moisture protection Farbe green Industrie 3-36 Content l Accessories Technical Data Value Density 0.81 g/cm 3 Viscosity (cp) 30/40 C Flash point 105 C Dielectric strength 180 kv/ 133

134 Chemical products Medium Voltage 2013 Easy Glide ubricant Easy-Glide simplifies and accelerates the feeding of cables through electrical installation conduits and cable ducts. Damage to the outer sheath is thus avoided. Available in light, practical 1050 ml plastic bottle or in handy 5 litre-buckets Agreeable odour Harmless ingredients Biologically degradable Non-corrosive Superior lubricating properties Non-adherent and does not stain Does not cause skin irritation, easily washable Nonflaable ubricant for feeding cables and wires through electrical installation conduits Accessories Drum Content l 1050ml Plastic bottle Easy Glide 5000ml Bucket Easy-Glide can be used with bare hands. Apply evenly. Technical Data Value max. Heat resistance 80 C 134

135 Chemical products Easy Clean Hand wipes Easy Clean combines a powerful cleaning solution with a microfiber cloth developed especially for thorough wiping. The special Easy Clean cleaning solution dissolves grime but is gentle on hands. It removes heavy fat stains, grease, glue, oil, tar, asphalt, ink, wax, carbon stains, graphite, grass stains and resin, amongst others. Heavy-duty one-step cleaning system Easily removes even the toughest stains Retains dirt without leaving traces Quick-drying cleaning solution with moisturising effect Biodegradable wipes Antibacterial Free from harmful substances Non-toxic Nonirritant Contains moisturising substances To remove ingrained dirt apply the darker side of the cloth. eave to soak in, then rub. If the stain has not come out, leave to soak for longer Remove most of the dirt using the darker textured side of the cloth, then polish with the soft side to achieve a completely clean residue-free finish Skin may feel slightly sticky after use due to moisturising emulsion, as absorption time varies according to skin type Note For external use only Avoid contact with eyes Keep dispenser away from heat sources Keep out of reach of children Easy Clean Content Piece Sales display in plastic dispenser Accessories 135

136 136 Medium Voltage 2013

137 Ahead through groundbreaking technology Page index 138 Catalogue number index 140 Index 137

138 Index A Accessory Kit for CTS 630A Cellplux Plug-In Cable Connectors...54 Al compression cable lug Al Compression connector...114, 115 Anti-corrosion spray Armour continuity for three-core joints...98, 121 Assembly guide for CSV screw connectors and CSK screw cable lugs AUF AUF(BS)...98 C Cable entry points for XPE- and paper-insulated cables CAE-3F...68 CAE-3I...67 CAE-F...44 CAE-I...42 CAESK-F...43 CAESK-I...41 CAM3-S...62 CAM-S...35 CG CGS 250A...46 CHE-3F(A)...64 CHE-3F(B)...66 CHE-3F(BS)...97 CHE-3I(A)...63 CHE-3I(B)...65 CHE-3I(BS)...96 CHE-F...39 CHE-F(BS)...95 CHE-I...37 CHE-I...94 CHEP(3Pb)-3F...88 CHEP(3Pb)-3I...87 CHEP(H)-3F...83 CHEP(H)-3I...82 CHEP-3F...78 CHEP-3I...77 CHM...33 CHM(BS)...92 CHM CHM3(BS)...93 CHMP(3Pb) CHMP(3Pb) CHMP(H) CHMP(H) CHMPP(3Pb) CHMPP(H) CHMPPR CHMPR CHMPR CHMPRSV CHMSV...32 CHMSV CHMSV CIK...53 CKM...36 CKS 630A...56 Clamp tool Conductive tape Connector element up to 24kV...47 Copper braid tape Coupling connector 630A up to 24kV...56 CPB CPES...57 CP-FM CP-P CPS...58 CSK CTKS 630A...50 CTKSA...51 CTKSA...52 CTS 630A...49 Cu compression cable lug...116, 117 Cu compression connector...112, 113 CVS 250A...47 CWS 250A...45 CWS 400A...48 D Detergent DK-A-D DK-CU-V DK-CU-V-D DV-A DV-CU-V DVZ-A-D DVZ-CU-V-D E Earthing accessories...99, 120 Easy Clean Easy Glide EGA EGA(BS)...99 Elbow plug-in cable connector...48 Elbow plug-in cable connector with capacitive measurement...45 H Hand wipes Heat-shrink torch kit Heat-shrink tubing up to 36kV High-voltage insulation tape I Indoor termination...77, 82, 87 INDUSTRIE ubricant M M...MS M...MSPB Mounting Ring...55 Multi tool

139 N No. 60, No No No No O Outdoor termination...78, 83, 88 Z ZINC SPRAY ZS-CTS...54 P Peeling tool Plug- In Surge Arrester...51, 52 Pressure spring Protective agent R Repair tape RF S Screw cable lugs for Cu and AI SEEV...28 SEEV-F...29 Single-core indoor termination...37, 42, 94 Single-core indoor termination with screw cable lugs...41 Single-core outdoor termination...39, 44, 95 Single-core outdoor termination with screw cable lugs...43 Single-core straight-through joint...33, 35, 92 Single-core straight-through joint with screw connector...32, 36 SMH3MS SRAT SRBB Straight plug-in cable connector with capacitive measurement...46 Straight-through joint...76, 81, 86 Straight-through joint with screw connector...60 T Test and Earthing Kit...57 Test-Kit...58 Thick wall heat-shrink tubing Three-core indoor termination...28, 63, 65, 67, 96 Three-core outdoor termination...29, 64, 66, 68, 97 Three-core straight-through joint...26, 27, 61, 93 Three-core straight-through joint with heat-shrink outer protection...62 Three-core straight-through joint with screw connector...59 Three-core transisition joint...72 T-plug and socket connexion...50 Transition joint 73, 74, 75, 79, 80, 84, 85 T-socket connexion...49 U UNIVERSA CEANER Index V Voltage-proof Insulating Cap

140 Medium Voltage 2013 Index

141 Medium Voltage 2013 Index

142 Medium Voltage 2013 Index

143 Index 143

144 Cellpack AG Electrical Products Anglikerstrasse Villmergen Schweiz Tel Fax Cellpack GmbH Carl-Zeiss-Straße Waldshut-Tiengen Deutschland Tel Fax Cellpack Benelux B.V. Keersluisweg EE Almere Buiten Nederland Tel Fax Cellpack Far East (PTE) TD. 128 Joo Seng Road # Singapore Tel Fax info@cellpack.com.sg Behr Bircher Cellpack BBC Malaysia Sdn. Bhd. No. 8, Jalan TU 50 Taman Tasik Utama Ayer Keroh Melaka Malaysia Tel Fax info@cellpack.com.my.my Behr Bircher Cellpack Ibérica, S.A. C/.Mas Pujol, nr. 47 Nave 4 Pol. Ind. Sector V es Franqueses del Vàllès Barcelona España Tel Fax comercial@cellpackiberica.com Behr Bircher Cellpack BBC France s.à.r.l. 277, Boulevard des Technologies udres France Tel Fax info@cellpack-ep.fr Cellpack Polska Sp. z o.o. ul. Matuszewska 14, Warszawa Polska Tel Fax biuro@cellpack.pl