Installation Manual TWM Performance Short Shifter Subaru STi 2008+

Size: px
Start display at page:

Download "Installation Manual TWM Performance Short Shifter Subaru STi 2008+"

Transcription

1 - 1 - Installation Manual TWM Performance Short Shifter Subaru STi Please Note: It is preferable to park on a flat surface, as you will have to engage and disengage the hand brake and shift from gears to neutral. The front of the car must be raised during this install. Always use jack stands while working under a car. Please read this manual completely before beginning to work on your car. Estimated Installation Time: minutes Tools required: Flat head screw drivers (small and large) Philips head screw driver 12mm wrench + ½ wrench Wire cutters Snap ring pliers Flash light or shop light (suggested) Needle nose pliers Shop towels or rags Metric socket set (with 12 mm socket) and a ratchet with extension ½ socket Hammer All purpose automotive grease (white Lithium based grease preferred) Jack At least two (2) jack stands

2 Unscrew the shift knob by rotating it counterclockwise. Put it aside in a safe place for reinstallation later. 2. Pull up on the e-brake cover as pictured and fold it inside out over the e-brake handle. There are two plastic tabs inside the cover that needs to be pushed toward the passenger side. The first tab is at the front of the e-brake cover and the other one at the rear (as pictured to the left). Pushing these tabs will allow the cover to be pulled up. 3. You now have access to a Philips head screw. Remove it with a Philips screwdriver and put it aside for re-install later.

3 Open the center compartment, remove the small carpet piece at the bottom and unbolt the 2 screws using a 10 mm socket with a ratchet and an extension or a Philips head screwdriver. 5. Pull the center console up and backward. You can leave it like that as it does not need to be removed from the car for the install. 6. Pull up on the shifter part of the center console about 1/2 as pictured to the left. Then pull straight toward the back of the car. You will have to pull hard as it s strongly in place. Pull up on the console until the boot is removed from the RL part of the shifter, however be careful as there is a connection under the console.

4 7. Turn the console inside out and unplug the connection as pictured to the left. Place the console aside for re-install later Remove the two white plastic tabs from the sound deadening material as pictured to the left. The second tab is at the front of the shifter. Put it aside for re-install later. 9. Remove the sound deadening material from the stock shifter as pictured to the left. Put it aside for re-install later. The next steps are pictured in a 2004 STi, however the process is the same in the STi.

5 This step requires the help of an assistant. Use the provided thin punch and a hammer to remove the spring pin from the reverse lockout mechanism. Be very careful and put a plastic bag or a rag on the side of the shifter where the spring pin comes out. Put the shifter in neutral and have an assistant with you to hold the shifter firmly in place and to avoid any stress to the transmission. Tap the pin out slowly and gently. Use caution not to lose the spring pin when it comes out. Put the spring pin aside in a safe place for re-installation later. 11. Remove the reverse lockout lever and the spring from the stock shifter and put them aside in a safe place for re-installation later. Cut the zip tie holding the reverse lock cable to the stock shifter.

6 Use a 12 mm wrench and a ratchet with a 12 mm socket to unscrew the bolt going through the shifter and shift rod. Remove the bolt and the nut from the shifter. They will not be re-used, however should be kept in case you revert back to stock in the future. 13. Read this step completely before you proceed. The snap ring at the base of the shifter must now be removed. Begin by removing the excess grease hiding the snap ring so it can be seen clearly. Use snap ring pliers to compress the snap ring. We have found that once the snap ring is compressed it is difficult to lift it out of the cylindrical base with the snap ring pliers alone.

7 - 7 - A small screwdriver can be inserted in the gap between the snap ring and the cylinder wall to hold it in place. With the flat head screwdriver in place, you can now use needle nose pliers to hold free the end of the snap ring and rotate it as pictured while pulling up gently. This will free the snap ring from the groove it is resting in. (Pictured in a 08 WRX) Use caution not to damage the snap ring by pulling up too hard, once you rotate the clip it should come free by pulling up lightly. 14. You can now remove the stock shifter from the car. Pull on the shifter backward, it will come out with the white plastic bushing, o-rings and snap ring attached to the shifter.

8 - 8 - Remove the metal sleeve from inside the shifter barrel as pictured to the left. It will not be re-installed however you should keep it in case you revert back to stock in the future. 15. With the stock shifter out of the car, remove the white bushing with the o-rings and the snap ring. Put them aside for re-install later.

9 Using a Phillips head screwdriver, remove the two (2) screws from the grey plastic piece on the stock shifter. Slide this piece off of the shifter and put everything aside for reinstallation on the TWM short shifter. Remove the small rubber grommet from the stock shifter and put it aside for re-installation on the short shifter later.

10 Grease the bottom pivot ball of the TWM short shifter and install the bottom white bushing on to the short shifter. Also install the snap ring by twisting it slightly to increase the size of the gap so it fits over the bottom shaft of the short shifter as shown to the left. 18. Install the rubber grommet and grey plastic piece with both screws on to the TWM short shifter.

11 Insert the reverse lock cable in the short shifter as pictured to the left. The uncovered portion of the cable should go all the way in to the short shifter. Install the short shifter back in place. Make sure the bottom and top o-rings are properly in place on the white bushing while you install it. If one of the o-rings comes loose from the bushing, remove the shifter and re-install the o-ring correctly in place.

12 Insert the snap ring back in the appropriate groove using snap ring pliers and a flat head screwdriver to push it down in the groove. It s important that the snap ring is seating properly in it s groove to ensure the shifter is solidly in place. 21. Connect the shift rod to the short shifter with the provided bolt and nut as pictured to the left. Using a ½ socket with a ratchet and ½ wrench, tighten it down to approximately 10 ftlbs. 22. Before proceeding to this step, you need to lift the front part of the car. Please refer to your car s owner manual for the procedure to lift the car. Always work safely and use a proper jack and at least two jackstands to hold the car up. Place wooden blocks or bricks behind the back wheels. Also make sure the car has cooled down before this step as you will be working close to the drivetrain and exhaust. Working under the car, locate the reverse lockout cable from under the shifter and follow it to the transmission case. You will need to move the lever where the cable is connected down and toward the rear of the car.

13 Continued from last page. You can use a small screwdriver handle to jam the lever in this position as pictured (we suggest to use a soft screwdriver handle as it will stay in place better than a hard screwdriver handle). It s better to have an assistant in the car to pull up on the RL cable because the access to the cable is restrained in the 08+ because of the heatshield. 23. Inside the car, lightly grease the black sound deadening part of the short shifter as pictured to the right. Use white lithium based grease. Install the spring and reverse lockout mechanism on the short shifter as pictured to the left.

14 Continued. 24. Line up the hole in the reverse lockout sleeve with the slot in the short shifter shaft and the hole in the reverse lockout cable inside the short shifter shaft. If you do not see the hole in the cable, the screwdriver holding the cable in place may have dropped from it s position. In this case, go back under the car to place the screwdriver handle back in position. Use the provided small punch and insert it sharp side first through the reverse lockout lever, short shifter slot and reverse lockout cable as pictured to the left. Do not pull up on the reverse lockout mechanism once the punch is in place. 25. Please read steps 25 and 26 entirely before proceeding. Do not pull up on the reverse lockout mechanism before these steps are completed Insert the spring pin in the provided special tool as pictured to the left. Press the pin on to the small punch as pictured on the next page.

15 This part requires the help of an assistant. Using the special tool, press the spring pin about halfway inside the shifter, pushing the punch out of the shifter from the other end at the same time. You should be able to do it by hand but a few light taps with a hammer may be required to push the pin in as far as shown to the left. Your assistant should recover the punch from the other side of the shifter to prevent it from dropping in the shifter assembly. 26. With the spring pin halfway inserted and the shifter in neutral, use the thin punch as pictured to the left to finish inserting the spring pin in the short shifter. The pointed end of the punch should be on the spring pin side and the flat side where you tap with the hammer. While your assistant holds the shifter very firmly in place, use a hammer on the punch to push the spring pin completely in place.

16 Continued. The spring pin is correctly in place once it sits flush on both sides with the reverse lockout lever as pictured to the left. The spring pin is inserted all the way in place. Once it s correctly in place, move the reverse lockout mechanism up and down a few times to make sure it s properly working. The screwdriver holding the lever in place under the car will fall off by itself. Before lowering the car to the ground, you will need to remove the 2 front bolts of the heat shield to access the RL cable. Use a 12 mm socket with a ratchet and extension and a 12 mm wrench for the second one as it s over the exhaust piping.

17 Using the provided zip tie, attach the RL cable to the shift rod as pictured. You do not need to over tighten the zip tie. Cut the excess of the zip tie and lower the car to the ground. 27. Use the provided zip tie to secure the reverse lockout cable to the short shifter as pictured to the left. Cut the excess of the zip tie, making sure not to leave sharp edges.

18 Re-install the center console, shift boot and shift knob by reversing steps 1 to 9. You are done, enjoy the drive and thank you for choosing TWM Performance! Legal Disclaimer TWM Performance is not responsible for the misuse, incorrect installation, or failure of any product we sell. Under no circumstances, including but not limited to negligence, will TWM Performance be liable for special or consequential damages that result from the use or inability to use our products. TWM Performance does not assume responsibility for any damage to the user, passenger or vehicle resulting from the operation of a TWM Performance product. TO PROTECT USERS FROM INJURY OR DEATH. THE USER ASSUMES ALL RISKS. Autocrossing, track events, and high speed driving are all dangerous activities - always drive responsibly and safely. Warranty Installation of some TWM Performance products may or may not void factory warranties. Always keep OEM equipment that has been replaced in case work is required at the dealer or the vehicle is sold. This warranty covers the original purchasing consumer. This warranty is limited to repair or replacement by TWM Performance of any TWM Performance product that fails because of a defect in materials or workmanship. Warranty does not cover the following: -Damage incurred to related vehicle components -Regular day to day wear on vehicle -Shipping costs for replacements -Installation costs and vehicle down time -Products that have been modified, incorrectly installed or misused. -Mounting hardware and bearings

Installation Manual TWM Performance Short Shifter Nissan 350Z, 370Z Infiniti G35, G37

Installation Manual TWM Performance Short Shifter Nissan 350Z, 370Z Infiniti G35, G37 Installation Manual TWM Performance Short Shifter Nissan 350Z, 370Z Infiniti G35, G37 It is preferable to park on a flat surface, as you will have to engage and disengage the hand brake and shift from

More information

Installation Manual TWM Performance Short Shifter Subaru Forester up to 2005

Installation Manual TWM Performance Short Shifter Subaru Forester up to 2005 - 1 - Installation Manual TWM Performance Short Shifter Subaru Forester up to 2005 Please Note: It is preferable to park on a flat surface, as you will have to engage and disengage the hand brake and shift

More information

Installation Manual TWM Performance Short Shifter 2008 Mitsubishi Lancer

Installation Manual TWM Performance Short Shifter 2008 Mitsubishi Lancer Page 1 Installation Manual TWM Performance Short Shifter 2008 Mitsubishi Lancer Please Note: It is preferable to park on a flat surface, as you will have to engage and disengage the hand brake and shift

More information

Installation Manual TWM Performance Kia Forte Short Shifter

Installation Manual TWM Performance Kia Forte Short Shifter Installation Manual TWM Performance Kia Forte 2009+ Short Shifter Begin the installation by parking on a flat surface, as you will have to engage and disengage the hand brake and shift from gears to neutral.

More information

Installation Manual TWM Performance Short Shifter Cobalt SS/SC, SS/TC, HHR SS, Ion Redline and Saab 9-3

Installation Manual TWM Performance Short Shifter Cobalt SS/SC, SS/TC, HHR SS, Ion Redline and Saab 9-3 Page 1 Installation Manual TWM Performance Short Shifter Cobalt SS/SC, SS/TC, HHR SS, Ion Redline and Saab 9-3 Please Note: It is preferable to park on a flat surface, as you will have to engage and disengage

More information

Installation Manual TWM Performance Short Shift Kit Stage 1 and Stage 2 MazdaSpeed 6

Installation Manual TWM Performance Short Shift Kit Stage 1 and Stage 2 MazdaSpeed 6 Page 1 Installation Manual TWM Performance Short Shift Kit Stage 1 and Stage 2 MazdaSpeed 6 Please Note: It is preferable to park on a flat surface, as you will have to engage and disengage the hand brake

More information

Installation Manual TWM Performance Full replacement short shifter assembly Civic all trims and models

Installation Manual TWM Performance Full replacement short shifter assembly Civic all trims and models Installation Manual TWM Performance Full replacement short shifter assembly 2006+ Civic all trims and models Begin the installation by parking on a flat surface, as you will have to engage and disengage

More information

Installation Manual TWM Performance Honda Accord 2008+

Installation Manual TWM Performance Honda Accord 2008+ Installation Manual TWM Performance Honda Accord 2008+ Begin the installation by parking on a flat surface, as you will have to engage and disengage the hand brake and shift from gears to neutral. If you

More information

Installation Manual TWM Performance 2010 Mazda 3 short shifter 5 and 6 speed non-mazdaspeed

Installation Manual TWM Performance 2010 Mazda 3 short shifter 5 and 6 speed non-mazdaspeed Installation Manual TWM Performance 2010 Mazda 3 short shifter 5 and 6 speed non-mazdaspeed Begin the installation by parking on a flat surface, as you will have to engage and disengage the hand brake

More information

Installation Manual TWM Performance Short Shift Kit 2003 And Up Saturn Ion

Installation Manual TWM Performance Short Shift Kit 2003 And Up Saturn Ion Installation Manual TWM Performance Short Shift Kit 2003 And Up Saturn Ion It s preferable to park on a flat surface, as you may have to engage and disengage the hand brake and shift from gears to neutral.

More information

2. Disconnect both plastic connectors beneath the rear part of the center console. Note their locations for re-installation.

2. Disconnect both plastic connectors beneath the rear part of the center console. Note their locations for re-installation. Installation Manual TWM Performance Short Shifter 2002 and up Subaru Impreza WRX/RS/TS 1996-2001 Subaru Impreza 2004 and Up Saab 9-2X 1996-2001 Subaru Legacy 1997-2004 Subaru Forester 1. Open the center

More information

Installation Manual TWM Performance Short Shift Kit 2006 and up Toyota Yaris

Installation Manual TWM Performance Short Shift Kit 2006 and up Toyota Yaris Installation Manual TWM Performance Short Shift Kit 2006 and up Toyota Yaris 1. Unscrew the shift knob by rotating counter clockwise. 2. Remove the carpet or mat at the bottom of the cup holder at the

More information

Installation Manual TWM Performance Short throw shifter 2001 and up Hyundai Accent

Installation Manual TWM Performance Short throw shifter 2001 and up Hyundai Accent Installation Manual TWM Performance Short throw shifter 2001 and up Hyundai Accent 1. Place the vehicle on a flat surface with blocks in front and behind the wheels preventing unwanted movement. The car

More information

Installation Manual TWM Performance Short Shift Kit Estimated Installation Time: Tools required:

Installation Manual TWM Performance Short Shift Kit Estimated Installation Time: Tools required: Page 1 Installation Manual TWM Performance Short Shift Kit 1993-2001 Nissan Altima 1991-2001 Infiniti G20 1991-2001 Nissan Sentra- 200SX 1991-1993 Nissan NX 1986-1989 Nissan Stanza 1995-2001 Nissan Maxima

More information

95-97 Toyota Tercel & Paseo Short Throw Shifter Installation Manual

95-97 Toyota Tercel & Paseo Short Throw Shifter Installation Manual 95-97 Toyota Tercel & 92-97 Paseo Short Throw Shifter Installation Manual Estimated Installation Time: 40-60 Minutes Tools Required: -Philips head screwdriver and flat head screwdriver -Bench vise -10mm,

More information

Installation Manual Short Shift Kit 2000 and up Toyota Celica 2000 and up MR Spyder

Installation Manual Short Shift Kit 2000 and up Toyota Celica 2000 and up MR Spyder Page 1 Installation Manual Short Shift Kit 2000 and up Toyota Celica 2000 and up MR Spyder 1. Unscrew the shift knob and remove the boot. 2. Remove cover which houses the lighter assembly. There are four

More information

Installation of the Toyota Celica TWM Performance Short Throw Shift Kit Plastic Shifter Assembly

Installation of the Toyota Celica TWM Performance Short Throw Shift Kit Plastic Shifter Assembly Installation of the 1992-1993 Toyota Celica TWM Performance Short Throw Shift Kit Plastic Shifter Assembly Page 1 1. Remove the stock shift knob and boot cover 2. Carefully slide an exacto knife under

More information

Instructions to Install TWM Performance Toyota Celica Short Throw Shift Kit

Instructions to Install TWM Performance Toyota Celica Short Throw Shift Kit Instructions to Install TWM Performance 1990-1991 Toyota Celica Short Throw Shift Kit Page 1 Step 1: Unscrew shift knob and remove console piece with boot. Step 2: Unbolt the seven bolts circled here (one

More information

Instructions to Install TWM Performance Toyota Celica Turbo 4WD Short Throw Shift Kit

Instructions to Install TWM Performance Toyota Celica Turbo 4WD Short Throw Shift Kit Instructions to Install TWM Performance 1990-1991 Toyota Celica Turbo 4WD Short Throw Shift Kit Page 1 Step 1: Unscrew shift knob and remove console piece with boot. Step 2: Unbolt the seven bolts circled

More information

Installation Manual TWM Performance Shift Boot 2006 and up Honda Civic Si

Installation Manual TWM Performance Shift Boot 2006 and up Honda Civic Si Page 1 Installation Manual TWM Performance Shift Boot 2006 and up Honda Civic Si Begin the installation by parking on a flat surface, as you may have to engage and disengage the hand brake and shift from

More information

Installation Manual TWM Performance Toyota GT86 / Scion FRS / Subaru BRZ Direct Replacement Short Shifter

Installation Manual TWM Performance Toyota GT86 / Scion FRS / Subaru BRZ Direct Replacement Short Shifter Installation Manual TWM Performance Toyota GT86 / Scion FRS / Subaru BRZ Direct Replacement Short Shifter Begin the installation by parking on a flat surface, place wooden blocks in front or behind the

More information

Installation Manual TWM Performance Chevrolet Camaro 5 th Gen Short Shifter

Installation Manual TWM Performance Chevrolet Camaro 5 th Gen Short Shifter Installation Manual TWM Performance Chevrolet Camaro 5 th Gen Short Shifter Begin the installation by parking on a flat surface, place wooden blocks in front or behind the wheels to prevent the car from

More information

Toyota Celica Short Throw Shift Kit Installation Manual (Metal Assembly)

Toyota Celica Short Throw Shift Kit Installation Manual (Metal Assembly) 1992-1993 Toyota Celica Short Throw Shift Kit Installation Manual (Metal Assembly) Page 1 1. Remove shift knob and plastic cover from shift assembly. 2. Remove the three nuts holding the top part of the

More information

Installation Manual TWM Performance Chevrolet Camaro 5 th Gen Full Replacement Short Shifter

Installation Manual TWM Performance Chevrolet Camaro 5 th Gen Full Replacement Short Shifter Installation Manual TWM Performance Chevrolet Camaro 5 th Gen Full Replacement Short Shifter Begin the installation by parking on a flat surface, place wooden blocks in front or behind the wheels to prevent

More information

Installation Instructions COMPETITION/PLUS SHIFTER Ford Mustang MT82 6-Speed Manual Transmission Catalog#

Installation Instructions COMPETITION/PLUS SHIFTER Ford Mustang MT82 6-Speed Manual Transmission Catalog# Installation Instructions COMPETITION/PLUS SHIFTER 2015-2017 Ford Mustang MT82 6-Speed Manual Transmission Catalog# 3916037 Rev. 00 WORK SAFELY! For maximum safety, perform this installation on a clean,

More information

Short Shifter Installation Instructions For Miata, 6-speed Manual Transmission

Short Shifter Installation Instructions For Miata, 6-speed Manual Transmission Short Shifter Installation Instructions For 2006-15 Miata, 6-speed Manual Transmission PART# 994-060 Required tools: 10mm deep socket Long extension Ratchet Small flathead screwdriver Phillips-head screwdriver

More information

Installation Instructions QUICKSILVER CONSOLE SHIFTER Fits: Chevelle / El Camino

Installation Instructions QUICKSILVER CONSOLE SHIFTER Fits: Chevelle / El Camino WORK SAFELY! For maximum safety, perform this installation on a clean, level surface and with the engine turned off. Place blocks or wedges in front of and behind both rear wheels to prevent movement in

More information

HURST COMP/PLUS SHIFTER 2015 Ford Mustang (Getrag MT82 six-speed manual transmission) Catalog # by Hurst Performance

HURST COMP/PLUS SHIFTER 2015 Ford Mustang (Getrag MT82 six-speed manual transmission) Catalog # by Hurst Performance FORM 159 0205 07/15 HURST COMP/PLUS SHIFTER 2015 Ford Mustang (Getrag MT82 six-speed manual transmission) Catalog #391 0205 2015 by Hurst Performance Thank you for purchasing the Hurst Comp/Plus Shifter.

More information

james Barone Racing Aftermarket Parts and Accessories

james Barone Racing Aftermarket Parts and Accessories Page1 james Barone Racing Aftermarket Parts and Accessories 2010 2013 MAZDASPEED 3 Short Throw Shifter Installation Instructions What you will need: Ratchet wrench 6 socket extension 10mm and 13mm socket

More information

Short Shifter Installation Instructions Miata 6-Speed manual

Short Shifter Installation Instructions Miata 6-Speed manual Tools required: 10mm deep socket long extension ratchet small flathead screwdriver phillips-head screwdriver Short Shifter Installation Instructions 2006-14 Miata 6-Speed manual IMPORTANT NOTE: This shifter

More information

Subaru 5-Speed Double Adjustable Short Throw Shifter

Subaru 5-Speed Double Adjustable Short Throw Shifter Subaru 5-Speed Double Adjustable Short Throw Shifter 1999+ Subaru Impreza 5-Speed 2004-2005 Subaru Forester XT 5-Speed Congratulations on your purchase of the COBB Tuning Double Adjustable Short Throw

More information

Steeda S550 Mustang Street Short Throw Shift Lever Installation Instructions For Part:

Steeda S550 Mustang Street Short Throw Shift Lever Installation Instructions For Part: Steeda S550 Mustang Street Short Throw Shift Lever Installation Instructions For Part: 555-7316 Tools required 1. 7mm socket 2. 10mm socket 3. Small flathead screwdriver 4. T20 torx bit or driver 5. Vise

More information

Remove the 3-11mm nuts holding mirror on. Don t drop the nuts!

Remove the 3-11mm nuts holding mirror on. Don t drop the nuts! 2005-2012 Ford Mustang Puddle Lamp Kit Parts List: Quantity: Tool List: LED Lamps 2 Flat head screwdriver Seals 2 Ratchet & Socket set OR Nuts 2 Adjustable Wrench Wiring harness 1 Drill & 11/16 th bit

More information

M-7210-Z3 Focus Short-Throw Shifter (fits 2000-April 2002) INSTALLATION INSTRUCTIONS

M-7210-Z3 Focus Short-Throw Shifter (fits 2000-April 2002) INSTALLATION INSTRUCTIONS Please visit www.fordracingparts.com for the most current instruction information!!! PLEASE READ ALL OF THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION. AT ANY TIME YOU DO NOT UNDERSTAND THE

More information

JBR Adjustable Short Shift Plate Kit Pre-Installation Instructions. Attaching the stand-off to the Shift Plate

JBR Adjustable Short Shift Plate Kit Pre-Installation Instructions. Attaching the stand-off to the Shift Plate JBR Adjustable Short Shift Plate Kit Pre-Installation Instructions Attaching the stand-off to the Shift Plate 1. With the Shift Plate facing up, insert the male end of the stand-off through the slotted

More information

Installation Instructions INDY SHIFTER Fits: Mustang Fastback & Convertible with MT-82 Transmission Catalog #

Installation Instructions INDY SHIFTER Fits: Mustang Fastback & Convertible with MT-82 Transmission Catalog # Installation Instructions INDY SHIFTER Fits: 2015-2018 Mustang Fastback & Convertible with MT-82 Transmission Catalog # 3916036 Watch our installation video on YouTube WORK SAFELY! For maximum safety,

More information

Steeda S550 MT-82 Tri-Ax Race Short Throw Shifter Installation Instructions For Parts: ,

Steeda S550 MT-82 Tri-Ax Race Short Throw Shifter Installation Instructions For Parts: , Steeda S550 MT-82 Tri-Ax Race Short Throw Shifter Installation Instructions For Parts: 555-7317, 555-7318 Tools required 1. 7mm socket 2. 10mm socket 3. 13mm socket 4. 15mm socket 5. 18mm socket 6. 3/8

More information

Installation Instructions HURST COMPETITION AND BILLET/PLUS SHIFTER Mustang w/5-speed Manual Transmission (GT only)

Installation Instructions HURST COMPETITION AND BILLET/PLUS SHIFTER Mustang w/5-speed Manual Transmission (GT only) Installation Instructions HURST COMPETITION AND BILLET/PLUS SHIFTER 2005-2010 Mustang w/5-speed Manual Transmission (GT only) Catalog# 3915201 WORK SAFELY! For maximum safety, perform this installation

More information

Installation Instructions Console Megashifter

Installation Instructions Console Megashifter Installation Instructions Console Megashifter 1968-1969 Camaro Part Number 81035 This B&M Megashifter is designed to fit in the console of a 1968-1969 Chevrolet Camaro. In 1968, these vehicles were equipped

More information

Chevrolet Cobalt Short Shifter Installation Manual

Chevrolet Cobalt Short Shifter Installation Manual Chevrolet Cobalt Short Shifter Installation Manual Pull shift boot down on the shifter shaft. Pull up on the shift knob to remove it. It requires some force. Remove the ebrake console, shifter console

More information

Installation Instructions

Installation Instructions Installation Instructions AMP RESEARCH Power Step by Bestop Automatic Retracting Running Board Vehicle Application Nissan Titan King Cab 2004 and newer (5 ft.) Part Number: 75106-01 Nissan Titan Crew Cab

More information

Ford Mustang V6 OEM-Style Fog Light Kit Parts List: Quantity: Tool List:

Ford Mustang V6 OEM-Style Fog Light Kit Parts List: Quantity: Tool List: 2015-2017 Ford Mustang V6 OEM-Style Fog Light Kit Parts List: Quantity: Tool List: LED Foglights/ Bezels 2 Flat head & Phillips screwdriver (if you ordered part#3600) Ratchet & Socket set OR Wiring harness

More information

MANUAL FOR THE NM100 ADJUSTABLE SHORT SHIFTER

MANUAL FOR THE NM100 ADJUSTABLE SHORT SHIFTER MANUAL FOR THE NM100 ADJUSTABLE SHORT SHIFTER P.O. BOX 313 ~ ODESSA, FL 33556 ~ 1-844-NUM-RACE Tools Needed T20 Torx Driver T27 Torx Driver Needle Nose Pliers ¼ Ratchet with 10MM Socket 3MM Allen Wrench

More information

Installation Instructions for the EVO3 Height-Adjustable Ultimate Short Shifter

Installation Instructions for the EVO3 Height-Adjustable Ultimate Short Shifter Installation Instructions for the EVO3 Height-Adjustable Ultimate Short Shifter for 1992-2005 325, 323, 318 and 1986-1994 525, 528, 535, 540 5-speed models only. (part number USSE3 and USSE5) Thank you

More information

Steeda S550 Mustang Street Short Throw Shift Lever Installation Instructions: &

Steeda S550 Mustang Street Short Throw Shift Lever Installation Instructions: & Steeda S550 Mustang Street Short Throw Shift Lever Installation Instructions: 555-7316 & 555-7322 Tools required 1. 7mm socket 2. 10mm socket 3. Small flathead screwdriver 4. T20 torx bit or driver 5.

More information

Performance Air Intake, 2015+

Performance Air Intake, 2015+ PARTS LIST AND PARTS LIST 1PC ALUMINUM INTAKE PIPE 1PC HIGH-FLOW, OILED AIR FILTER 1PC SILICONE INDUCTION HOSE 1PC AIRBOX 1PC 1/16 RUBBER STRIPPING, 9 LENGTH 1PC 1/16 RUBBER STRIPPING, 8.5 LENGTH 1PC WORM-GEAR

More information

PARTS TOOLS. Set Screw. Washer (2) Blue Bushing (2) Black Bushing (2) B&M Short Throw Shifter. Jam Nut Grease. Retaining Ring (2) Insert (2)

PARTS TOOLS. Set Screw. Washer (2) Blue Bushing (2) Black Bushing (2) B&M Short Throw Shifter. Jam Nut Grease. Retaining Ring (2) Insert (2) Installation Instructions SHORT THROW SHIFTER Fits: Porsche Boxter, Boxter S, 911, 996 Cayman & Cayman S models See Application Guide for specific year ranges and engine sizes Catalog # 45135 WORK SAFELY!

More information

Installation Instructions for the EVO3 Height-Adjustable Ultimate Short Shifter. for F80 M3 and F82 M4

Installation Instructions for the EVO3 Height-Adjustable Ultimate Short Shifter. for F80 M3 and F82 M4 Installation Instructions for the EVO3 Height-Adjustable Ultimate Short Shifter for 2013+ F80 M3 and F82 M4 part number USSF80 Thank you for purchasing the Ultimate Shift Kit. Please read these directions

More information

Detroit Speed, Inc. Electric Headlight Door Kit Corvette P/N: &

Detroit Speed, Inc. Electric Headlight Door Kit Corvette P/N: & Detroit Speed, Inc. Electric Headlight Door Kit 1968-82 Corvette P/N: 122006 & 122007 The Detroit Speed Inc. Electric Headlight Door Kit replaces the stock vacuum actuated system on all 1968-82 Corvettes.

More information

PARTS B&M Billet Knob B&M Billet Insert. O-Ring. Reverse Lockout Plate. Isolator. Nylon Slide Assy and Jam nut. Printed in the U.S.A.

PARTS B&M Billet Knob B&M Billet Insert. O-Ring. Reverse Lockout Plate. Isolator. Nylon Slide Assy and Jam nut. Printed in the U.S.A. Installation Instructions Precision Sport Shifter 2000 and up VW GOLF IV, JETTA IV (including GLI 6-spd), GTI, CABRIO, BEETLE, R32 (including 4-motion) 2000 and up Audi A3 1.8L and 1.9L Turbo Diesel, 1999-2002

More information

Installation Instructions Z-Gate Shifter

Installation Instructions Z-Gate Shifter Installation Instructions Z-Gate Shifter Part Number 80681 1998, 2001 by B&M Racing and Performance Products The B&M Z-Gate shifter can be used in vehicles equipped with most popular three speed automatic

More information

Ford Mustang GT-Style Fog Light Kit Parts List: Quantity: Tool List:

Ford Mustang GT-Style Fog Light Kit Parts List: Quantity: Tool List: 2013-2014 Ford Mustang GT-Style Fog Light Kit Parts List: Quantity: Tool List: Fog light (Left& Right) 2 Flat head & Phillips screwdriver Upper grille with surround 1 Ratchet & Socket set OR Lower grille

More information

Detroit Speed, Inc. Electric Headlight Door Kit Corvette P/N: &

Detroit Speed, Inc. Electric Headlight Door Kit Corvette P/N: & Detroit Speed, Inc. Electric Headlight Door Kit 1968-82 Corvette P/N: 122006 & 122007 The Detroit Speed Inc. Electric Headlight Door Kit replaces the stock vacuum actuated system on all 1968-82 Corvettes.

More information

97-02 JEEP TJ BODY LIFT KIT INSTRUCTIONS

97-02 JEEP TJ BODY LIFT KIT INSTRUCTIONS 92RC60500 97-02 JEEP TJ BODY LIFT KIT INSTRUCTIONS Congratulations on your purchase of a new Rough Country 2 /3 Body Lift. We are committed to providing you with the best product available for the best

More information

Installation Instructions Short Throw Shifter

Installation Instructions Short Throw Shifter Installation Instructions Short Throw Shifter 1996-1999 VW Golf VR6 1998-1999 VW eetle 1998-1999 VW Jetta/ora VR6 Part Number 45106 2001 by &M Racing and Performance Products LLC This &M Short Throw Shifter

More information

Z-Gate Universal Shifter

Z-Gate Universal Shifter Installation Instructions Z-Gate Universal Shifter Fits: GM, Ford, Lincoln and Chrysler Transmissions See Application Guide for Specific Applications Part #80681 Rev 06/01/2018 WORK SAFELY! For maximum

More information

Installation Instructions HURST COMP STICK KIT Dodge Challenger (with AUTO-STICK)

Installation Instructions HURST COMP STICK KIT Dodge Challenger (with AUTO-STICK) Installation Instructions HURST COMP STICK KIT 2008-2012 Dodge Challenger (with AUTO-STICK) 1590402 REV01 08/17/15 Catalog# 538 0402 & 538 0403 2009, 2015 Hurst Performance WORK SAFELY! For maximum safety,

More information

Installation Instructions

Installation Instructions Instructions Created by an: Inchworm Tacoma Dual Case Adapter Installation Instructions Suggested Tools: CAUTION: Safety glasses should be worn at all times when working with vehicles and related tools

More information

C6 (includingg Z06) Catalog # 45034

C6 (includingg Z06) Catalog # 45034 Installation Instructionss Precision Sport Shifter Fits: 2008-20133 Corvette C6 (includingg Z06) Catalog # 45034 WORK SAFELY! For maximum safety, perform this installation on a clean, level surface and

More information

ADVANCE ADAPTERS INC. P/N: JEEP TJ & (XJ 84-01) ATLAS 4 SPEED CABLE SHIFTER units built after 5/1/12

ADVANCE ADAPTERS INC. P/N: JEEP TJ & (XJ 84-01) ATLAS 4 SPEED CABLE SHIFTER units built after 5/1/12 Paso Robles, CA 93447 PAGE 1 OF 9 Telephone: (800) 350-2223 Fax: (805) 238-4201 Page Rev. Date: 05-12-15 KIT CONSISTS OF: No. Qty Part No. Description 1 1 302051 BASE- TWIN STICK MOUNT 2 1 302080 STUD

More information

DISASSEMBLY We suggest the vehicle be allowed to cool for an hour or two before you begin since you will be working around the exhaust system.

DISASSEMBLY We suggest the vehicle be allowed to cool for an hour or two before you begin since you will be working around the exhaust system. Installation Instructions Short Throw Shifter Fits: 1984-2006 BMW 3 Series E30, E36 & E46 1987-2006 BMW 3 Series M3 & 1996-2002 BMW 5 Series Catalog # 45126 WORK SAFELY! For maximum safety, perform this

More information

SUBARU STI SUBARU WRX V1.0

SUBARU STI SUBARU WRX V1.0 2008-2018 SUBARU STI 2009-2018 SUBARU WRX V1.0 Congratulations on purchasing the finest automotive accessories on the market available for your vehicle. They will add a nice touch of class to your vehicle

More information

Evora shiftr111 Installation Instructions Rev. B Page 1 of 14

Evora shiftr111 Installation Instructions Rev. B Page 1 of 14 Evora shiftr111 Installation Rev. B Page 1 of 14 READ FITTING INSTRUCTIONS IN FULL BEFORE INSTALLATION This article is sold without warranty expressed or implied. No warranty or representation is made

More information

IPSCO STS (Short Throw Shifter) Installation Instructions Dodge Viper WARNING

IPSCO STS (Short Throw Shifter) Installation Instructions Dodge Viper WARNING WARNING Modification of your vehicle with the parts identified above may alter its stock performance; the buyer hereby expressly assumes all risks associated with any such modification. DISCLAIMER OF WARRANTY

More information

Technical Support (707)

Technical Support (707) Installation Instructions CONSOLE MEGASHIFTER Fits: 1982-1992 Camaro & Firebird w/automatic Transmission *except 1988-1992 Firebird Formula Model Catalog # 80692 WORK SAFELY! For maximum safety, perform

More information

Installation Instructions. QuickSilver Shifter. Fits: GM, Ford, Chrysler Transmissions See Application Guide for Specific Applications Part # 80683

Installation Instructions. QuickSilver Shifter. Fits: GM, Ford, Chrysler Transmissions See Application Guide for Specific Applications Part # 80683 Installation Instructions QuickSilver Shifter Fits: GM, Ford, Chrysler Transmissions See Application Guide for Specific Applications Part # 80683 WORK SAFELY! For maximum safety, perform this installation

More information

Changing the Struts on a WK Jeep CRD

Changing the Struts on a WK Jeep CRD Changing the Struts on a WK Jeep CRD Step by Step By Chirpz Disclaimer: I do not claim that this procedure is the right way or even the best way to change your struts. This is what I did after reading

More information

Remove 4 circled pins. Route wiring along dashed line. Remove the 2 9mm nuts and black retaining plate that secure extractor.

Remove 4 circled pins. Route wiring along dashed line. Remove the 2 9mm nuts and black retaining plate that secure extractor. 2015 Ford Mustang Turn Signal Hood Kit Parts List: Quantity: Tool List: Bracket & pre-installed lamp 2 Flat head screwdriver Wiring harness 1 Phillips screwdriver PB-3660 Parts Bag 1 Ratchet & Socket set

More information

JEEP TJ & (XJ 84-01) ATLAS 2 SP.

JEEP TJ & (XJ 84-01) ATLAS 2 SP. KIT CONSISTS OF: No. Qty Part No. Description 4320 Aerotech Center Way, Page 1 of 9 1 1 302051-RLE BASE- TWIN STICK MOUNT 42RLE 2 1 302080 STUD BOLT 1/2"-13 X 7 (XJ) 3 1 303120 SERRATED LOCK NUT 1/2" X

More information

Low Range HD 2 Inch Body Lift Kit (Sidekick, GV, Vitara, Tracker, X90) SKU# KSP-BL2

Low Range HD 2 Inch Body Lift Kit (Sidekick, GV, Vitara, Tracker, X90) SKU# KSP-BL2 Low Range HD 2 Inch Body Lift Kit (Sidekick, GV, Vitara, Tracker, X90) SKU# KSP-BL2 Installation Instructions Background: These instructions are designed for installing the 2 body lift. They can also be

More information

2014 & up MAZDA 3, 6 and CX5 2.0 & 2.5L Oil Catch Can Installation Instructions

2014 & up MAZDA 3, 6 and CX5 2.0 & 2.5L Oil Catch Can Installation Instructions Page1 James Barone Racing Aftermarket Parts and Accessories 2014 & up MAZDA 3, 6 and CX5 2.0 & 2.5L Oil Catch Can Installation Instructions Tooling: Jack Jack stands or ramps Ratchet wrench 3 extension

More information

Suzuki Samurai 6.5 Transfer Case Gear Kit, KIT

Suzuki Samurai 6.5 Transfer Case Gear Kit, KIT Suzuki Samurai 6.5 Transfer Case Gear Kit, 105004-3-KIT Kit Contents: Gear, 26 Spline/26 Tooth 1.0 Gear, 44 Tooth 1.0 Gear, 58 Tooth/23 Tooth 1.0 Gear, 67 Tooth/ 27 Tooth 1.0 Counter Shaft 1.0 Counter

More information

TK08 TUNING KIT TECHNICAL MANUAL FOR 16/26/27/28 SERIES SHOCKS Revised 6/17/14

TK08 TUNING KIT TECHNICAL MANUAL FOR 16/26/27/28 SERIES SHOCKS Revised 6/17/14 Tech Line: (952) 985-5675 Fax (952) 985-5679 21730 Hanover Ave. Lakeville, MN 55044 www.qa1.net www.facebook.com/qa1motorsports TK08 TUNING KIT TECHNICAL MANUAL CONTENTS UNDER PRESSURE! USE EXTREME CAUTION

More information

***THE OWNER'S MANUAL MUST BE GIVEN TO THE END USE CUSTOMER AFTER COMPLETING THE INSTALLATION.***

***THE OWNER'S MANUAL MUST BE GIVEN TO THE END USE CUSTOMER AFTER COMPLETING THE INSTALLATION.*** INSTALLATION INSTRUCTIONS FOR THE MOTOR TRIKE HARLEY MECHANICAL REVERSE 1999-2006 FIVE SPEED FLH LAST UPDATED: OCTOBER 2011 AS THE INSTALLER OF THIS MECHANICAL REVERSE, YOU MUST BECOME FAMILIAR WITH PROPER

More information

INSTALLATION INSTRUCTIONS JEEP 2011-UP JK SECURITY FULL CONSOLE #274

INSTALLATION INSTRUCTIONS JEEP 2011-UP JK SECURITY FULL CONSOLE #274 INSTALLATION INSTRUCTIONS JEEP 2011-UP JK SECURITY FULL CONSOLE #274 PARTS CHECKLIST Tuffy Console #9 Left Front Mounting Bracket #10 Right Front Mounting Bracket #11 Electronics mounting bracket #12 Divider

More information

ROUSH Active IO Exhaust. Installation Instructions P/N: (R LITE) Fastback GT Convertible GT V8

ROUSH Active IO Exhaust. Installation Instructions P/N: (R LITE) Fastback GT Convertible GT V8 Installation Instructions P/N: 422128 (R1318-5231LITE) Fastback GT Convertible GT V8 39555 Schoolcraft Rd, Plymouth MI, 48170 800.59.ROUSH ROUSH Active IO Exhaust Installation Instructions P/N: 422128

More information

TK08 TUNING KIT TECHNICAL MANUAL FOR 16/26/27/28 SERIES SHOCKS Revised 6/25/14 Tech Line: (952) Fax (952)

TK08 TUNING KIT TECHNICAL MANUAL FOR 16/26/27/28 SERIES SHOCKS Revised 6/25/14 Tech Line: (952) Fax (952) Tech Line: (952) 985-5675 Fax (952) 985-5679 21730 Hanover Ave. Lakeville, MN 55044 www.qa1.net www.facebook.com/qa1motorsports TK08 TUNING KIT TECHNICAL MANUAL CONTENTS UNDER PRESSURE! USE EXTREME CAUTION

More information

TCI Trans-Scat

TCI Trans-Scat Page 1 of 5 Return to Instruction Sheet index TCI 400000 Trans-Scat Turbo Hydramatic 400-1965-Up This kit will allow you to re-program your transmission valve body. This kit will give you firm positive

More information

Max IV Rear Axle Replacement For models after Serial Number and all rear splined axle replacements.

Max IV Rear Axle Replacement For models after Serial Number and all rear splined axle replacements. Max IV Rear Axle Replacement For models after Serial Number 19089 and all rear splined axle replacements. 10/8/03 Max IV Snap Ring Rear Axle replacement.doc Tools required: 9/16 Wrench 6 Extension Steel

More information

Depress each tab as you pull the bezel off. The bezels are tight. L.H. shown.

Depress each tab as you pull the bezel off. The bezels are tight. L.H. shown. 2013-2014 Ford Mustang V6 & Boss 302 Lower Valance Fog Light Kit Parts List: Quantity: Tool List: Fog light & bulb with bracket 2 Flat head & Phillips screwdriver Black bezels 2 Ratchet & Socket set OR

More information

Installation Instructions

Installation Instructions Instructions Created by an: 1986-1995 Toyota Pickup 4Runner Hilux Front Ball Joint Spacer Kit - 2.5" 64mm Lift by Low Range Off-Road (SKU# TSP-BJS-1.5 & TSP-BJS-1.5-W/Shocks) Installation Instructions

More information

Installation Instructions

Installation Instructions Instructions Created by an: Inchworm Gear Clockable Toyota Dual Transfer Case Adapter Kit, 21 or 23 Spline SKU# TCASE-IW-300-000 Installation Instructions CAUTION: Safety glasses should be worn at all

More information

Holden VE Pontiac G8 Vauxhall VXR8 & Chevrolet Lumina - Ripshift Installation Instructions

Holden VE Pontiac G8 Vauxhall VXR8 & Chevrolet Lumina - Ripshift Installation Instructions Holden VE Pontiac G8 Vauxhall VXR8 & Chevrolet Lumina - Ripshift Installation Instructions 1 P a g e Thank you for purchasing a GM Motorsport RIPSHIFT Some of the feature of your new shifter are 1. Adjustable

More information

HURST COMP STICK KIT 2008 and up DODGE CHALLENGER (with AUTO-STICK) Catalog # &

HURST COMP STICK KIT 2008 and up DODGE CHALLENGER (with AUTO-STICK) Catalog # & FORM 159 0402 03/09 HURST COMP STICK KIT 2008 and up DODGE CHALLENGER (with AUTO-STICK) Catalog #538 0402 & 538 0403 2009 by Hurst Perfomance Thank you for purchasing the Hurst Comp Stick Kit for your

More information

Barton Short Throw Shifter 11/12 V6, GT Mustang:

Barton Short Throw Shifter 11/12 V6, GT Mustang: Barton Short Throw Shifter 11/12 V6, GT Mustang: Tools Required: 10mm deep socket Socket wrench 10 extension for socket wrench Jack Jack stand Small piece of wood Small hook tool (recommended) *can be

More information

Porsche 911/996/997 Carrera Do-It-Yourself Convertible Top Hydraulic Cylinder Inspection, Removal and Shipping Instructions

Porsche 911/996/997 Carrera Do-It-Yourself Convertible Top Hydraulic Cylinder Inspection, Removal and Shipping Instructions Porsche 911/996/997 Carrera Do-It-Yourself Convertible Top Hydraulic Cylinder Inspection, Removal and Shipping Instructions Disclaimer: These instructions are intended as a guide. Cabriolet Hydraulics

More information

R O A D S M I T H TRIKE CONVERSIONS BY THE TRIKE SHOP

R O A D S M I T H TRIKE CONVERSIONS BY THE TRIKE SHOP R O A D S M I T H TRIKE CONVERSIONS BY THE TRIKE SHOP Please thoroughly review the instructions before and during installation. Keep in mind that this product was designed to be installed by trained dealer

More information

MAX FLOW FUEL KIT KIA FORTE SX HYUNDAI VELOSTER TURBO INSTALLATION INSTRUCTIONS

MAX FLOW FUEL KIT KIA FORTE SX HYUNDAI VELOSTER TURBO INSTALLATION INSTRUCTIONS MAX FLOW FUEL KIT KIA FORTE SX 2014+ HYUNDAI VELOSTER TURBO INSTALLATION INSTRUCTIONS Installation: Tools needed: 1/4 or 3/8 drive ratchet Different length extensions 8mm socket / 10mm socket / 12mm socket

More information

INSTALLATION INSTRUCTIONS: LONG TRAVEL KIT 07+ FJ CRUISER and 05+ TACOMA

INSTALLATION INSTRUCTIONS: LONG TRAVEL KIT 07+ FJ CRUISER and 05+ TACOMA INSTALLATION INSTRUCTIONS: LONG TRAVEL KIT 07+ FJ CRUISER and 05+ TACOMA ISNTALLATION DIFFICULTY: Advanced APPROX TIME: 6-8 Hours REQUIRED TOOLS: 14mm-35mm sockets, wrenches, and ratchet 9/16 and 5/8 12

More information

Installation Instructions QUICKSILVER SHIFTER Fits: Chevrolet Camaro Pontiac Firebird Catalog # 80688

Installation Instructions QUICKSILVER SHIFTER Fits: Chevrolet Camaro Pontiac Firebird Catalog # 80688 Installation Instructions QUICKSILVER SHIFTER Fits: 1973-1981 Chevrolet Camaro 1970-1981 Pontiac Firebird Catalog # 80688 WORK SAFELY! For maximum safety, perform this installation on a clean, level surface

More information

AmTryke Adult Recumbent Model HP1000 #50-HC-1000

AmTryke Adult Recumbent Model HP1000 #50-HC-1000 AmTryke Adult Recumbent Model HP1000 #50-HC-1000 TOOLS Needed for Assembly 5 mm Allen Wrench 8 mm Socket or Wrench 10 mm Socket or Wrench 14 mm Socket or Wrench 15 mm Socket or Wrench 22 mm Socket or Adjustable

More information

Installation Instructions Unimatic Shifter

Installation Instructions Unimatic Shifter Installation Instructions Unimatic Shifter Universal Shifter for Automatic Transmissions Part Number 80775 2010, 2000 by B&M Racing & Performance Products The B&M Unimatic is a universal shifter that will

More information

PRO RATCHET UNIVERSAL SHIFTER

PRO RATCHET UNIVERSAL SHIFTER Installation Instructions PRO RATCHET UNIVERSAL SHIFTER Fits: GM, Ford and Chryslers w/automatic Transmission See Application Guide for Specific Vehicles Catalog # 80842 WORK SAFELY! For maximum safety,

More information

URD Short Shifter Installation Tacoma 5 speed Runner 5 speed

URD Short Shifter Installation Tacoma 5 speed Runner 5 speed URD Short Shifter Installation 1995-2004 Tacoma 5 speed 1996-2002 4Runner 5 speed Introduction: URD introduced our first short throw shifter for the 05+ Tacoma 6 speed transmission. This unit became very

More information

TH400 STREETFIGHTER SERIES VALVE BODY MANUAL/AUTO VALVE BODY INSTALLATION INSTRUCTIONS

TH400 STREETFIGHTER SERIES VALVE BODY MANUAL/AUTO VALVE BODY INSTALLATION INSTRUCTIONS 1 INSTRUCTIONS TH400 STREETFIGHTER SERIES VALVE BODY 1965-87 MANUAL/AUTO VALVE BODY INSTALLATION INSTRUCTIONS TCI 222400 TCI 222400 ALLOWS AUTOMATIC SHIFT FEATURES IN THE DRIVE POSITION Thank you for choosing

More information

James Barone Racing Custom Fabrication of Aftermarket Parts and Accessories Ford Focus ST Rear Engine Mount Installation Instructions

James Barone Racing Custom Fabrication of Aftermarket Parts and Accessories Ford Focus ST Rear Engine Mount Installation Instructions James Barone Racing Custom Fabrication of Aftermarket Parts and Accessories 2013+ Ford Focus ST Rear Engine Mount Installation Instructions Tools Required: Ratchet 6 Extension 13mm 6-Point Socket 15mm

More information

INSTALLATION INSTRUCTIONS QA1 P/N x400, x500, x600, x400, x500, x F100 Front Coil-over Suspension System

INSTALLATION INSTRUCTIONS QA1 P/N x400, x500, x600, x400, x500, x F100 Front Coil-over Suspension System INSTALLATION INSTRUCTIONS QA1 P/N 52620-x400, 52620-x500, 52620-x600, 52621-x400, 52621-x500, 52621-x600 65-72 F100 Front Coil-over Suspension System TOOLS AND SUPPLIES REQUIRED Floor Jack Two (2) Jack

More information

R O A D S M I T H TRIKE CONVERSIONS BY THE TRIKE SHOP

R O A D S M I T H TRIKE CONVERSIONS BY THE TRIKE SHOP R O A D S M I T H TRIKE CONVERSIONS BY THE TRIKE SHOP Please thoroughly review the instructions before and during installation. Keep in mind that this product was designed to be installed by trained dealer

More information

Slave Cylinder Weep Hole Drilling Procedure

Slave Cylinder Weep Hole Drilling Procedure Slave Cylinder Weep Hole Drilling Procedure Tools Required: T20 Torx Driver T25 Torx Driver T25 Torx Bit with ¼ Ratchet Wrench 4mm Hex Key (Allen wrench) 5mm Hex Key 6mm Hex Key 8mm Hex Key 12mm Hex Key

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Accessory Application Publications No. AII 24307 SYSTEM 2003 ELEMENT Issue Date DEC 2002 NOTE: An optional keyless entry system (sold seperately) must be installed before you

More information