Toyota Celica Short Throw Shift Kit Installation Manual (Metal Assembly)
|
|
- Maurice Chase
- 5 years ago
- Views:
Transcription
1 Toyota Celica Short Throw Shift Kit Installation Manual (Metal Assembly) Page 1 1. Remove shift knob and plastic cover from shift assembly. 2. Remove the three nuts holding the top part of the assembly and their respective bolts.
2 Page 2 3. Remove the two clips holding the shifter to the shift linkage rods. 4. Remove the two bolts on the upper part of the assembly. Then slide the two pins out of their holes, this will separate the white section and the shifter from the assembly.
3 Page 3 5. Pop the shifter out of the large white cup. This step may require a fair amount of strength. Step 6: Use the cup remover tool included with the kit to remove both plastic cups on the original shifter. To do so, place the cup remover tool on top of the open jaws of a vice, the jaws should be approximately 1 apart. Hang the shifter from the tool as shown, be sure the shifter is inserted completely into the slot in the tool. Insert a punch into the center hole through the plastic cup and tap firmly with a hammer to separate the original shifter from cup. Repeat for 2nd cup.
4 Page 4 7. Put the cups on the TWM shifter, be sure to grease the two smaller balls as well as the main pivot ball. Then pop the large white cup back on. 8. Re-assemble the upper part of the assembly, see step 4. The piece pictured is not necessary and can be removed.
5 Page 5 9. Place the spacers provided between the upper and lower parts of the assembly. Note: This may be easier if the bolt is threaded from the top down (opposite of what is pictured). To help in getting the nut threaded on to the underside you can use some grease to help stick it to your finger. 10. Re-attach the two clips that connect the shifter to the shift linkage rods and replace the plastic cover and boot. Now you are ready to drive.
6 Page 6 Legal Disclaimer TWM Performance is not responsible for the misuse, incorrect installation, or failure of any product we sell. Under no circumstances, including but not limited to negligence, will TWM Performance be liable for special or consequential damages that result from the use or inability to use our products. TWM Performance does not assume responsibility for any damage to the user, passenger or vehicle resulting from the operation of a TWM Performance product. TO PROTECT USERS FROM INJURY OR DEATH. THE USER ASSUMES ALL RISKS. Autocrossing, track events, and high speed driving are all dangerous activities - always drive responsibly and safely. Warranty Installation of some TWM Performance products may or may not void factory warranties. Always keep OEM equipment that has been replaced in case work is required at the dealer or the vehicle is sold. This warranty covers the original purchasing consumer. This warranty is limited to repair or replacement by TWM Performance of any TWM Performance product that fails because of a defect in materials or workmanship. Warranty does not cover the following: -Damage incurred to related vehicle components -Regular day to day wear on vehicle -Shipping costs for replacements -Installation costs and vehicle down time -Products that have been modified, incorrectly installed or misused. -Mounting hardware and bearings
Instructions to Install TWM Performance Toyota Celica Short Throw Shift Kit
Instructions to Install TWM Performance 1990-1991 Toyota Celica Short Throw Shift Kit Page 1 Step 1: Unscrew shift knob and remove console piece with boot. Step 2: Unbolt the seven bolts circled here (one
More informationInstallation of the Toyota Celica TWM Performance Short Throw Shift Kit Plastic Shifter Assembly
Installation of the 1992-1993 Toyota Celica TWM Performance Short Throw Shift Kit Plastic Shifter Assembly Page 1 1. Remove the stock shift knob and boot cover 2. Carefully slide an exacto knife under
More informationInstructions to Install TWM Performance Toyota Celica Turbo 4WD Short Throw Shift Kit
Instructions to Install TWM Performance 1990-1991 Toyota Celica Turbo 4WD Short Throw Shift Kit Page 1 Step 1: Unscrew shift knob and remove console piece with boot. Step 2: Unbolt the seven bolts circled
More informationInstallation Manual Short Shift Kit 2000 and up Toyota Celica 2000 and up MR Spyder
Page 1 Installation Manual Short Shift Kit 2000 and up Toyota Celica 2000 and up MR Spyder 1. Unscrew the shift knob and remove the boot. 2. Remove cover which houses the lighter assembly. There are four
More informationInstallation Manual TWM Performance Short Shift Kit 2006 and up Toyota Yaris
Installation Manual TWM Performance Short Shift Kit 2006 and up Toyota Yaris 1. Unscrew the shift knob by rotating counter clockwise. 2. Remove the carpet or mat at the bottom of the cup holder at the
More information95-97 Toyota Tercel & Paseo Short Throw Shifter Installation Manual
95-97 Toyota Tercel & 92-97 Paseo Short Throw Shifter Installation Manual Estimated Installation Time: 40-60 Minutes Tools Required: -Philips head screwdriver and flat head screwdriver -Bench vise -10mm,
More informationInstallation Manual TWM Performance Short throw shifter 2001 and up Hyundai Accent
Installation Manual TWM Performance Short throw shifter 2001 and up Hyundai Accent 1. Place the vehicle on a flat surface with blocks in front and behind the wheels preventing unwanted movement. The car
More information2. Disconnect both plastic connectors beneath the rear part of the center console. Note their locations for re-installation.
Installation Manual TWM Performance Short Shifter 2002 and up Subaru Impreza WRX/RS/TS 1996-2001 Subaru Impreza 2004 and Up Saab 9-2X 1996-2001 Subaru Legacy 1997-2004 Subaru Forester 1. Open the center
More informationInstallation Manual TWM Performance Honda Accord 2008+
Installation Manual TWM Performance Honda Accord 2008+ Begin the installation by parking on a flat surface, as you will have to engage and disengage the hand brake and shift from gears to neutral. If you
More informationInstallation Manual TWM Performance Short Shifter 2008 Mitsubishi Lancer
Page 1 Installation Manual TWM Performance Short Shifter 2008 Mitsubishi Lancer Please Note: It is preferable to park on a flat surface, as you will have to engage and disengage the hand brake and shift
More informationInstallation Manual TWM Performance Short Shift Kit 2003 And Up Saturn Ion
Installation Manual TWM Performance Short Shift Kit 2003 And Up Saturn Ion It s preferable to park on a flat surface, as you may have to engage and disengage the hand brake and shift from gears to neutral.
More informationInstallation Manual TWM Performance Short Shift Kit Stage 1 and Stage 2 MazdaSpeed 6
Page 1 Installation Manual TWM Performance Short Shift Kit Stage 1 and Stage 2 MazdaSpeed 6 Please Note: It is preferable to park on a flat surface, as you will have to engage and disengage the hand brake
More informationInstallation Manual TWM Performance 2010 Mazda 3 short shifter 5 and 6 speed non-mazdaspeed
Installation Manual TWM Performance 2010 Mazda 3 short shifter 5 and 6 speed non-mazdaspeed Begin the installation by parking on a flat surface, as you will have to engage and disengage the hand brake
More informationInstallation Manual TWM Performance Short Shifter Subaru Forester up to 2005
- 1 - Installation Manual TWM Performance Short Shifter Subaru Forester up to 2005 Please Note: It is preferable to park on a flat surface, as you will have to engage and disengage the hand brake and shift
More informationInstallation Manual TWM Performance Kia Forte Short Shifter
Installation Manual TWM Performance Kia Forte 2009+ Short Shifter Begin the installation by parking on a flat surface, as you will have to engage and disengage the hand brake and shift from gears to neutral.
More informationInstallation Manual TWM Performance Toyota GT86 / Scion FRS / Subaru BRZ Direct Replacement Short Shifter
Installation Manual TWM Performance Toyota GT86 / Scion FRS / Subaru BRZ Direct Replacement Short Shifter Begin the installation by parking on a flat surface, place wooden blocks in front or behind the
More informationInstallation Manual TWM Performance Short Shift Kit Estimated Installation Time: Tools required:
Page 1 Installation Manual TWM Performance Short Shift Kit 1993-2001 Nissan Altima 1991-2001 Infiniti G20 1991-2001 Nissan Sentra- 200SX 1991-1993 Nissan NX 1986-1989 Nissan Stanza 1995-2001 Nissan Maxima
More informationInstallation Manual TWM Performance Chevrolet Camaro 5 th Gen Short Shifter
Installation Manual TWM Performance Chevrolet Camaro 5 th Gen Short Shifter Begin the installation by parking on a flat surface, place wooden blocks in front or behind the wheels to prevent the car from
More informationInstallation Manual TWM Performance Full replacement short shifter assembly Civic all trims and models
Installation Manual TWM Performance Full replacement short shifter assembly 2006+ Civic all trims and models Begin the installation by parking on a flat surface, as you will have to engage and disengage
More informationInstallation Manual TWM Performance Short Shifter Nissan 350Z, 370Z Infiniti G35, G37
Installation Manual TWM Performance Short Shifter Nissan 350Z, 370Z Infiniti G35, G37 It is preferable to park on a flat surface, as you will have to engage and disengage the hand brake and shift from
More informationInstallation Manual TWM Performance Chevrolet Camaro 5 th Gen Full Replacement Short Shifter
Installation Manual TWM Performance Chevrolet Camaro 5 th Gen Full Replacement Short Shifter Begin the installation by parking on a flat surface, place wooden blocks in front or behind the wheels to prevent
More informationInstallation Manual TWM Performance Shift Boot 2006 and up Honda Civic Si
Page 1 Installation Manual TWM Performance Shift Boot 2006 and up Honda Civic Si Begin the installation by parking on a flat surface, as you may have to engage and disengage the hand brake and shift from
More informationInstallation Manual TWM Performance Short Shifter Subaru STi 2008+
- 1 - Installation Manual TWM Performance Short Shifter Subaru STi 2008+ Please Note: It is preferable to park on a flat surface, as you will have to engage and disengage the hand brake and shift from
More informationInstallation Manual TWM Performance Short Shifter Cobalt SS/SC, SS/TC, HHR SS, Ion Redline and Saab 9-3
Page 1 Installation Manual TWM Performance Short Shifter Cobalt SS/SC, SS/TC, HHR SS, Ion Redline and Saab 9-3 Please Note: It is preferable to park on a flat surface, as you will have to engage and disengage
More informationjames Barone Racing Aftermarket Parts and Accessories
Page1 james Barone Racing Aftermarket Parts and Accessories 2010 2013 MAZDASPEED 3 Short Throw Shifter Installation Instructions What you will need: Ratchet wrench 6 socket extension 10mm and 13mm socket
More informationJBR Adjustable Short Shift Plate Kit Pre-Installation Instructions. Attaching the stand-off to the Shift Plate
JBR Adjustable Short Shift Plate Kit Pre-Installation Instructions Attaching the stand-off to the Shift Plate 1. With the Shift Plate facing up, insert the male end of the stand-off through the slotted
More informationJames Barone Racing Aftermarket Parts and Accessories
Page1 James Barone Racing Aftermarket Parts and Accessories What you will need: 2014+ Mazda 3, 6 and CX-5 Adjustable Rear Camber Arm Installation Instructions. Jack, jack stands Socket wrench Socket wrench
More information2014+ Mazda 3/6 & CX-5 Front Sway Bar Installation Instructions
Page1 James Barone Racing 2014+ Mazda 3/6 & CX-5 Front Sway Bar Installation Instructions Tools Required: Jack & jack stands or a lift Socket wrench 3 and 12 socket extensions 10mm, 14mm, 17mm, 19mm socket
More informationMAZDASPEED 3 JBR Oil Catch Can VTA Kit Installation Instructions
James Barone Racing Aftermarket Parts and Accessories 07-2013 MAZDASPEED 3 JBR Oil Catch Can VTA Kit Installation Instructions These installation instructions are written assuming you already have a JBR
More informationJames Barone Racing Custom Fabrication of Aftermarket Parts and Accessories Mazda 3 and MAZDASPEED 3 Mud Flap Installation Instructions
James Barone Racing Custom Fabrication of Aftermarket Parts and Accessories 2010+ Mazda 3 and MAZDASPEED 3 Mud Flap Installation Instructions To protect and avoid damage to your new JBR Mud Flaps care
More informationSteeda S550 MT-82 Tri-Ax Race Short Throw Shifter Installation Instructions For Parts: ,
Steeda S550 MT-82 Tri-Ax Race Short Throw Shifter Installation Instructions For Parts: 555-7317, 555-7318 Tools required 1. 7mm socket 2. 10mm socket 3. 13mm socket 4. 15mm socket 5. 18mm socket 6. 3/8
More information4. Remove the cotter pin that secures the castle nut to the axle. Once you have done this remove the castle nut and pull off the hub/rotor assembly.
780 Professional Drive N. Shreveport, LA 71105 Phone (318)-524-2270 Fax (318)-524-2297 Max Clearance Honda Pioneer 1000 Front Forward Arched Control Arm Kit Read before Installation This product is designed
More informationJBR Mazda 3 & Mazdaspeed 3 Adjustable Rear Camber Arm Installation Instructions
james Barone Racing Aftermarket Parts and Accessories JBR 2004 2013 Mazda 3 & Mazdaspeed 3 Adjustable Rear Camber Arm Installation Instructions Tooling: Jack and jack stands Ratchet wrench 17mm socket
More informationCanopy Frame Assembly Instructions
Canopy Frame Assembly Instructions 14 Foot // 22 Foot // 24 Foot // 26 Foot // 28 Foot // 30 Foot // 32 Foot INTRODUCTION The Starr line of Boat Lift Canopy Frames by Great Lakes Entry Systems has been
More informationSteeda S550 Mustang Street Short Throw Shift Lever Installation Instructions For Part:
Steeda S550 Mustang Street Short Throw Shift Lever Installation Instructions For Part: 555-7316 Tools required 1. 7mm socket 2. 10mm socket 3. Small flathead screwdriver 4. T20 torx bit or driver 5. Vise
More informationHalf Door Installation Instructions
Half Door Installation Instructions For: CJ5 (1976-1983) Part Number: 53027 Congratulations on your purchasing decision. Bestop designed these Doors to give you years of dependability and performance with
More information2. Remove front wheels.
1 PARTS DIAGRAM 2 Installation Instructions: (PASSENGER SIDE) 1. Place jack under center of RUV front end and lift until front wheels clear the ground. Be careful to support the RUV properly so that it
More informationINSTALLATION INSTRUCTIONS AND OWNER S MANUAL
INSTALLATION INSTRUCTIONS AND OWNER S MANUAL Thank you for purchasing ADARAC Truck Bed Rack. Agri-Cover, Inc. proudly manufactured this product using superior quality materials and workmanship. With proper
More informationStop! Read This Important Information.
Stop! Read This Important Information. Stop, Do Not Proceed, Read This This door replacement kit is designed for the replacement of doors on a Supertop ONLY! This door will not work on any other style
More informationChevrolet Cobalt Short Shifter Installation Manual
Chevrolet Cobalt Short Shifter Installation Manual Pull shift boot down on the shifter shaft. Pull up on the shift knob to remove it. It requires some force. Remove the ebrake console, shifter console
More informationInstallation Instructions INDY SHIFTER Fits: Mustang Fastback & Convertible with MT-82 Transmission Catalog #
Installation Instructions INDY SHIFTER Fits: 2015-2018 Mustang Fastback & Convertible with MT-82 Transmission Catalog # 3916036 Watch our installation video on YouTube WORK SAFELY! For maximum safety,
More informationREPAIR PARTS MANUAL MODEL NUMBER SB240 (MFG. ID. NO ) Snow Thrower Rev BY Printed in U.S.A.
MANUAL MODEL NUMBER SB0 (MFG. ID. NO. 919100000) Snow Thrower 19 9- Rev. 0..0 BY Printed in U.S.A. AUGER HOUSING / IMPELLER ASSEMBLY 1 1 1 7 1 10 1 9 7 8 7 8 11 1 0 9 0 9 10 18 8 19 8 19 19 0 10 8 19 1
More informationSubaru 5-Speed Double Adjustable Short Throw Shifter
Subaru 5-Speed Double Adjustable Short Throw Shifter 1999+ Subaru Impreza 5-Speed 2004-2005 Subaru Forester XT 5-Speed Congratulations on your purchase of the COBB Tuning Double Adjustable Short Throw
More informationPREDICTIVE STEERING HUBS. Service Manual
2015 PREDICTIVE STEERING HUBS Service Manual SRAM LLC WARRANTY EXTENT OF LIMITED WARRANTY Except as otherwise set forth herein, SRAM warrants its products to be free from defects in materials or workmanship
More information16K Revolution Service Kit Instructions 86016
86016 Equipment Required: Wrenches: 15/16, 1 1/8, Torque Wrench, Rubber Mallet Included Service Kit Items: 1 Qty. (1) Wear Plate 2 Qty. (1) Pivot Bushing 3 Qty. (1) Bearing Cup 4 Qty. (1) Bearing 1 5 Qty.
More information2017-Present Can-Am Maverick X3 XRS Front Upper A-Arm Kit *Installation Instructions*
2017-Present Can-Am Maverick X3 XRS Front Upper A-Arm Kit *Installation Instructions* PART# 370-90350 Introduction - Installation requires a qualified mechanic. - Read instructions carefully and study
More informationHAND THROTTLE CONTROL KIT
1 HAND THROTTLE CONTROL KIT www.teraflex.com #87000 #87002 Important Notes: Prior to beginning this or any installation read these instructions to familiarize yourself with the required steps and evaluate
More informationTrail-Creeper Dual Transfer Case Adapter
Trail-Creeper Dual Transfer Case Adapter Installation Instructions For Kits: 100001-1-KIT 21 Spline 100006-1-KIT 23 Spline KIT Contents: 23 or 21 Spline Coupler 1.0 Adapter Plate w/ Bearings Installed
More informationASSEMBLY INSTRUCTIONS Reese Elite Series FIFTH WHEEL SLIDER HITCH
ASSEMBLY INSTRUCTIONS Reese Elite Series FIFTH WHEEL SLIDER HITCH DEALER/INSTALLER: (1) Provide this Manual to end user. (2) Physically demonstrate procedures in this Manual to end user. (3) Have end user
More informationINSTALLATION/OPERATION
INSTALLATION/OPERATION ULTRA POWER TWIN II-30 P/N 39-941705 APPLICATION The primary purpose of your Power Twin II is to provide rock solid stabilization for maximum comfort while using your RV in a parked
More informationREPAIR PARTS MANUAL MODEL NUMBER PM105 (MFG. ID. NO ) Snow Thrower BY Printed in U.S.A.
MANUAL MODEL NUMBER PM10 (MFG. ID. NO. 9191001103) Snow Thrower 3 0 1-8 08.11.0 BY Printed in U.S.A. AUGER HOUSING / IMPELLER ASSEMBLY SNOW THROWER - MODEL NO. PM10 (9191001103), PRODUCT NO. 91 91 00-11
More informationGeneral Guidelines. Instructions for Part # SC-SWING-AWAY-V2. Safety
Instructions for Part # SC-SWING-AWAY-V2 General Guidelines It is the user s responsibility to read and follow all instructions. Keep these instructions with the product at all times and review before
More informationInstallation Guide for the JK Wrangler 4-Inch Suspension System with FlexArms
INSTALLATION GUIDE Installation Guide for the JK Wrangler 4-Inch Suspension System with FlexArms TeraFlex, Inc. Tera5680 Manufacturing, Inc. W Dannon Way 5251 South Commerce West Jordan, UT 84081 Dr. Phone/801.288.2585
More informationInstallation manual. Toyota Tundra 4WD & 2WD. 2.5 Suspension kit. Part # Part # Important customer information:
Installation manual 2007-2016 Toyota Tundra 4WD & 2WD 2.5 Suspension kit Part # 53070 sj11082011rev.03 Part # 53070 2007-2016 Toyota Tundra 4WD & 2WD 2.5 Suspension kit Part # Description Qty. 53070-01
More informationINSTRUCTION MANUAL 22K - Fifth Wheel Hitch
You can take it with you. INSTRUCTION MANUAL 22K - Fifth Wheel Hitch Product No. 30033 DEALER/INSTALLER: (1) Provide this Manual to end user. (2) Physically demonstrate hitching and unhitching procedures
More informationSteeda S550 Mustang Street Short Throw Shift Lever Installation Instructions: &
Steeda S550 Mustang Street Short Throw Shift Lever Installation Instructions: 555-7316 & 555-7322 Tools required 1. 7mm socket 2. 10mm socket 3. Small flathead screwdriver 4. T20 torx bit or driver 5.
More informationREPAIR PARTS MANUAL MODEL NUMBER PM85 (MFG. ID. NO ) Snow Thrower Rev SR Printed in U.S.A.
MANUAL MODEL NUMBER PM8 (MFG. ID. NO. 990000) Snow Thrower 3 0 8-3 Rev. 0.08.09 SR Printed in U.S.A. AUGER HOUSING / IMPELLER ASSEMBLY SNOW THROWER - MODEL NO. PM8 (990000), PRODUCT NO. 9 9 00-0 3 0 9
More informationOWNER'S MANUAL. Please Do Not Return This Product To The Store!
TABLE TENNIS TABLE MODEL NO. T87 OWNER'S MANUAL 1. Read this manual carefully before starting assembly. Read each step completely before beginning each step. 2. Some smaller parts may be shipped inside
More informationUNIVERSAL FLOOR SHIFT CONVERSION KIT
UNIVERSAL FLOOR SHIFT CONVERSION #7668 These instructions apply to the following MR. GASKET products: 7668 - Universal Floor Shift Conversion Kit, Fits Most Rear-Wheel Drive Car Applications With Automatic
More informationJames Barone Racing Custom Fabrication of Aftermarket Parts and Accessories Ford Focus ST Rear Engine Mount Installation Instructions
James Barone Racing Custom Fabrication of Aftermarket Parts and Accessories 2013+ Ford Focus ST Rear Engine Mount Installation Instructions Tools Required: Ratchet 6 Extension 13mm 6-Point Socket 15mm
More informationInstallation Instructions
Installation Instructions To ensure that your installation proceeds smoothly--please read these instructions carefully before you begin. P r o d u c t s Luxury Faucets and Accessories Savina Product Numbers
More information5 th Airborne Sidewinder Service Kit Instructions 94316
94316 Equipment Required: Wrenches: 15/16, Torque Wrench, Rubber Mallet 3 4 5 2 Included Service Kit Items: 1 Qty. (1) Wear Plate 2 Qty. (1) Wear Bushing 3 Qty. (1) Wear Disc 4 Qty. (4) 5/8-11x2 GRD8 Bolt
More information16K and 19K Sidewinder TM Service Kit Instructions 86005
86005 Equipment Required: Wrenches: 15/16, 1 1/8, Torque Wrench, Rubber Mallet Included Service Kit Items: 1 Qty. (1) Wear Plate 2 Qty. (6) 5/8 Conical Washer 3 Qty. (2) Wedge Bolt, 5/8-11 X 1 3/4 GRD
More informationInstruction set # 7068 Cognito Motorsports, Inc. Upper Control Arm Leveling Kit for GM 8-Lug #UCAK (Boxed Style)
Cognito Motorsports, Inc. Upper Control Arm Leveling Kit for 2001-2010 GM 8-Lug #UCAK100010 (Boxed Style) Introduction - These control arms will not affect the height of the truck, the height is determined
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Thank you for purchasing ROXTERTM Hitch Mounted Mud Flaps. Agri-Cover, Inc. proudly manufactured these mud flaps using superior quality materials and workmanship. With proper
More informationReplace - A - Top Installation Instructions
Replace - A - Top Installation Instructions For: Suzuki Samurai Part Number: 51361 Congratulations on your purchasing decision. Bestop designed this Convertible Top to give you years of dependability and
More informationNOTICE- THIS K-MEMBER REQUIRES THE USE OF COIL OVER SUSPENSION. K-MEMBER WILL NOT WORK WITH FACTORY STYLE SPRINGS.
Technical Support Line: (952) 985-5675 Email: Info@QA1.net 21730 Hanover Ave. Lakeville, MN 55044 www.qa1.net INSTALLATION INSTRUCTIONS MUSTANG K-MEMBER P/N MUK11, MUK12, MUK13 NOTICE- THIS K-MEMBER REQUIRES
More informationHURST COMP/PLUS SHIFTER 2015 Ford Mustang (Getrag MT82 six-speed manual transmission) Catalog # by Hurst Performance
FORM 159 0205 07/15 HURST COMP/PLUS SHIFTER 2015 Ford Mustang (Getrag MT82 six-speed manual transmission) Catalog #391 0205 2015 by Hurst Performance Thank you for purchasing the Hurst Comp/Plus Shifter.
More information04 & 14 F FRONT 1.0 REAR LEVELING KIT INSTALLATION
INSTRUCTION PART NO 15312 KIT NO 3836 04 & 14 F-150 2.0 FRONT 1.0 REAR LEVELING KIT INSTALLATION READ INSTRUCTIONS COMPLETELY THROUGH BEFORE STARTING. FAILURE TO ADHERE TO THE INSTRUCTIONS WILL VOID ANY
More informationHi-Rise 18K 5TH WHEEL CONVERSION HITCH
ASSEMBLY INSTRUCTIONS Hi-Rise 18K 5TH WHEEL CONVERSION HITCH DEALER/INSTALLER: (1) Provide this Manual to end user. END USER: (1) Read and follow this Manual every time you use Hitch. (2) Save this Manual
More information4331 EUCALYPTUS AVE. ~~ CHINO, CA Fax FORD F-250/350 SUPER DUTY 4WD FTS RADIUS ARM BOX KIT
4331 EUCALYPTUS AVE. ~~ CHINO, CA 91710 909-597-7800 Fax 909-597-7185 2005-2007 FORD F-250/350 SUPER DUTY 4WD FTS22099 10 RADIUS ARM BOX KIT 4331 EUCALYPTUS AVE. ~~ CHINO, CA 91710 909-597-7800 Fax 909-597-7185
More informationInstallation manual 3 suspension system Toyota Tacoma 4 x 4 & PreRunner Part # sj rev.03
Part #: 52904 1995-2004 Toyota Tacoma 4 x 4 & PreRunner 3 suspension system Parts list: Part # Description Qty. 52904-01 Rear brake proportioning valve bracket 1 52907-02 Front pre load spacer 2 52904-03
More informationInstallation Instructions READ THOROUGHLY BEFORE BEGINNING Signature Series Rail Kit Dodge Ram Trucks-all, including Mega-cabs
INDEX Failure to follow all of these instructions may result in death or serious injury!. GUIDELINES FOR MATCHING TOW VEHICLE AND TRAILER. Pages -. DRILLED AND BOLTED INSTALLATION FIGURE. Page 4. NO-DRILL,
More informationJames Barone Racing Custom Fabrication of Aftermarket Parts and Accessories. JBR MAZDASPEED 3 Small Battery Box Installation Instruction
James Barone Racing Custom Fabrication of Aftermarket Parts and Accessories Tools Required: Socket wrench 10mm Deep Socket Socket Extension 10mm wrench Philips head screw driver JBR MAZDASPEED 3 Small
More informationFORD F-250/350 SUPER DUTY 4WD FTS22142 FRONT DUAL SHOCK SYSTEM
2011-2015 FORD F-250/350 SUPER DUTY 4WD FTS22142 FRONT DUAL SHOCK SYSTEM FTS22142 2011 F250/350 MULTI SHK KIT FT30446 Hardware Kit 1 FT30167BK UPPER HOOP DRVR 05 FORD SD 10 1/2-13 X 3 HEX CAP SCREW ZINC
More informationTOYOTA L/C TRANSFER CASE TWIN STICK
KIT CONSITS OF: No: Qty Part No. Description PAGE 1 OF 5 Page Rev. Date: 10-16-18 1. 1 *715575 HIGH LOW PIVOT BLOCK 2. 1 715576 T/C HIGH LOW SHIFTER LEVER 3. 1 *715577 2WD/4WD PIVOT BLOCK 4. 1 715579 PIVOT
More informationImproving the gearshift feel in an SW20.
Improving the gearshift feel in an SW20. Part one In 3 parts. The SW20 gearshift can be often be greatly improved by eliminating play in the shift linkages, and this article covers three areas that need
More informationSHOTLOCK OWNER S MANUAL TABLE OF CONTENTS -3-
SHOTLOCK OWNER S MANUAL Thank you for purchasing a ShotLock Solo Vault. Now, you can enjoy peace-of-mind knowing your personal defense shotgun is always close, secure and ready. When the first-responder
More informationInstallation Instructions
Installation Instructions To ensure that your installation proceeds smoothly--please read these instructions carefully before you begin. P r o d u c t s Luxury Faucets and Accessories Savina Product Numbers
More informationDetroit Speed, Inc. Rear Coilover Tower Brace Kit Camaro P/N:
Detroit Speed, Inc. Rear Coilover Tower Brace Kit 2016+ Camaro P/N: 042433 The Detroit Speed, Inc. 2016+ Camaro Rear Coilover Tower Brace Kit is a bolt-in design that increases overall vehicle stiffness.
More informationInstallation manual 3 front / 2 rear suspension system FJ / Runner Part # sj110607rev.03
Part #: 52000 2007-2014 Toyota FJ / 2003-2009 4Runner 3 front / 2 rear suspension system Parts list: Part # Description Qty. 52907-01 Pre load spacer 2 52907-02 Strut spacer 2 MO3531BK-01 Rear coil spring
More informationInstallation Instructions To ensure that your installation proceeds smoothly--please read these instructions carefully before you begin.
Single Lever Vessel Faucet Installation Instructions To ensure that your installation proceeds smoothly--please read these instructions carefully before you begin. P r o d u c t s Luxury Faucets and Accessories
More informationJackhammer Trolley JHT
Jackhammer Trolley JHT OPERATOR S MANUAL CONTENTS ABOUT THIS MANUAL 2 - Key Terms 2 - Disclaimer 3 PRODUCT INFORMATION 4 - Safety Information 4 o General Safety Instructions 4 o Safety Stickers 5-6 - Warranty
More informationINSTALLATION INSTRUCTIONS QA1 P/N R , R , R R , R , R F100 Rear Coil-over Conversion System
INSTALLATION INSTRUCTIONS QA1 P/N R120-170, R120-200, R120-250 R220-170, R220-200, R220-250 65-72 F100 Rear Coil-over Conversion System TOOLS AND SUPPLIES REQUIRED Floor Jack Two (2) Jack Stands Drill
More informationPontoon and Tri-Toon Bunk Assembly Instructions
Pontoon and Tri-Toon Bunk Assembly Instructions INTRODUCTION The Starr line of Boat Lift Canopy Frames by Great Lakes Entry Systems has been engineered to provide the best possible performance, long term
More informationB C A. EN bike trays with ratchet arms 2. EN front wheel holder 2. EN rear wheel holder assembly 2. EN 4mm self tapping screw 10
T2 PRO 9036 2 BIKE ADD-ON FOR (2" HITCH) = North American English PARTS INCLUDED B C A D A E F G H I J K L M N part description qty. A add-on mast 1 B bike trays with ratchet arms 2 C front wheel holder
More informationOperator s Manual. Twin Rear Bagger For FastAttach Compatible Lawn Tractors
Operator s Manual Twin Rear Bagger For FastAttach Compatible Lawn Tractors Models OEM-190-601 (for 38-inch & 42-inch decks) OEM-190-602 (for 46-inch decks) MTD PRODUCTS INC. P.O. BOX 368022 CLEVELAND,
More informationInstallation Instructions COMPETITION/PLUS SHIFTER Ford Mustang MT82 6-Speed Manual Transmission Catalog#
Installation Instructions COMPETITION/PLUS SHIFTER 2015-2017 Ford Mustang MT82 6-Speed Manual Transmission Catalog# 3916037 Rev. 00 WORK SAFELY! For maximum safety, perform this installation on a clean,
More informationWRANGLER TJ INSTALLATION INSTRUCTIONS Kit #: TJ251K/KN/KST/KSTN TJ401K/KN/KST/KSTN
WRANGLER TJ INSTALLATION INSTRUCTIONS Kit #: TJ251K/KN/KST/KSTN TJ401K/KN/KST/KSTN Before beginning the installation, read these instructions and the enclosed driver s WARNING NOTICE thoroughly and completely.
More informationINSTALLATION INSTRUCTIONS QA1 P/N x400, x500, x600, x400, x500, x F100 Front Coil-over Suspension System
INSTALLATION INSTRUCTIONS QA1 P/N 52620-x400, 52620-x500, 52620-x600, 52621-x400, 52621-x500, 52621-x600 65-72 F100 Front Coil-over Suspension System TOOLS AND SUPPLIES REQUIRED Floor Jack Two (2) Jack
More informationValveSentry USER S MANUAL REVISED 8/6/16 IMPORTANT! PLEASE READ CAREFULLY AND SAVE
ValveSentry USER S MANUAL REVISED 8/6/16 IMPORTANT! PLEASE READ CAREFULLY AND SAVE This user s manual contains important information about your ValveSentry device s operation. If you are installing this
More informationSuzuki Samurai 6.5 Transfer Case Gear Kit, KIT
Suzuki Samurai 6.5 Transfer Case Gear Kit, 105004-3-KIT Kit Contents: Gear, 26 Spline/26 Tooth 1.0 Gear, 44 Tooth 1.0 Gear, 58 Tooth/23 Tooth 1.0 Gear, 67 Tooth/ 27 Tooth 1.0 Counter Shaft 1.0 Counter
More informationJames Barone Racing Aftermarket Parts and Accessories Ford Focus ST Front Sway Bar Installation Instructions. Page1
Page1 James Barone Racing Aftermarket Parts and Accessories 2013+ Ford Focus ST Front Sway Bar Installation Instructions Tools Required: Jack Lift or ramps Ratchet wrench Torque Wrench 6 and 12 Extension
More informationWarnings and Precautions FAILURE TO READ, UNDERSTAND AND FOLLOW THESE INSTRUCTIONS MAY LEAD TO SERIOUS INJURY OR DEATH!
Instruction Booklet 2006 Summit ATV Pak-Mule Single Axle 84000 Summit ATV Pak-Mule Tandem Axle 84002!! READ ME FIRST!!! Please read carefully BEFORE using you new Summit ATV Product. Congratulations! You
More informationTK08 TUNING KIT TECHNICAL MANUAL FOR 16/26/27/28 SERIES SHOCKS Revised 6/17/14
Tech Line: (952) 985-5675 Fax (952) 985-5679 21730 Hanover Ave. Lakeville, MN 55044 www.qa1.net www.facebook.com/qa1motorsports TK08 TUNING KIT TECHNICAL MANUAL CONTENTS UNDER PRESSURE! USE EXTREME CAUTION
More informationINSTALLATION INSTRUCTIONS GM Lower Control Arms P/N 52337, 52437, 52364, 52464, 52319, 52419, 52320, 52420, 52366, 52466, 52368, 52468
INSTALLATION INSTRUCTIONS GM Lower Control Arms P/N 52337, 52437, 52364, 52464, 52319, 52419, 52320, 52420, 52366, 52466, 52368, 52468 TOOLS AND SUPPLIES REQUIRED Floor Jack Jack Stands Wrench Set Hex
More informationRENEGADE SLATE BUMPER POOL TABLE ASSEMBLY INSTRUCTIONS
RENEGADE SLATE BUMPER POOL TABLE ASSEMBLY INSTRUCTIONS NG2404PG THANK YOU! Thank you for purchasing this product. We work around the clock and around the globe to ensure that our products maintain the
More informationInstallation manual Toyota Tundra 4WD & 2WD - 2 front leveling kit Toyota Sequoia 4WD & 2WD - 2 front leveling kit Part # 52070
Part # 52070 2007-2016 Toyota Tundra 4WD & 2WD 2008-2011 Toyota Sequoia 4WD & 2WD 2 front leveling kit Part # Description Qty. 52070-01 Front strut spacers 2 52070NB Hardware bag 1 52070INST Instruction
More informationMULTI-STAGE FILTRATION SYSTEM INSTALLATION INSTRUCTIONS
MULTI-STAGE FILTRATION SYSTEM INSTALLATION INSTRUCTIONS Model #: 30101 Model #: 30102 Replacement Cartridge INSTALLATION GUIDE ABOUT THIS SYSTEM Congratulations on your purchase of the 30101 Multi-Stage
More informationREPAIR PARTS MANUAL MODEL NUMBER SB300 (MFG. ID. NO ) Snow Thrower Rev BY Printed in U.S.A.
MANUAL MODEL NUMBER SB00 (MFG. ID. NO. 990000) Snow Thrower 9 9-9 Rev. 0..0 BY Printed in U.S.A. AUGER HOUSING / IMPELLER ASSEMBLY 9 0 9 0 9 9 9 9 0 9 9 9 0 0 KEY PART NO. NO. DESCRIPTION AUGER HOUSING
More information