Installation Manual TWM Performance Short throw shifter 2001 and up Hyundai Accent

Size: px
Start display at page:

Download "Installation Manual TWM Performance Short throw shifter 2001 and up Hyundai Accent"

Transcription

1 Installation Manual TWM Performance Short throw shifter 2001 and up Hyundai Accent 1. Place the vehicle on a flat surface with blocks in front and behind the wheels preventing unwanted movement. The car will be in neutral with the handbrake off for some of the installation so it is important that the vehicle be stable. Unscrew the shift knob by rotating counter clockwise; set it aside for reinstallation later. 2. Remove the Philips head screws from the front of the console on both the passenger s and driver s side. 3. Remove the Philips head screws from the rear of the console on both the passenger and driver s side. 4. Pull the handbrake up. Lift the rear half of the console, then pull the entire console upward to unclip the clips at the front of the console. Remove the rear half of the console from the vehicle and place in a safe location for re-installation. 5. Remove the Philips head screws securing the rear portion of the front half of the console.

2 6. Lift up on the rear portion of the front half of the console to remove it from the vehicle and place in a safe location for re-installation. This may be easier with the handbrake down. 7. Note: Wear safety glasses and use caution during this step. Insert a flat head screwdriver behind the clip on the right front side of the assembly and pry the clip off. The clip may be broken in the process but a new one is included with the TWM shifter. A hammer may be used to insert the flat head screw driver behind the clip as it is quite rigid. Alternatively, a dremel tool with a cutting disc may be used to cut the clip off. 8. Use a hammer to lightly tap the pin out of the assembly. Place the pin in a safe place for reinstallation. 9. Use needle nose pliers to remove the clip securing the side shift cable to the L shaped arm on the driver s side of the assembly. Remove the arm and spring from the assembly while taking note of the orientation of the spring for re-installation. If possible, keep the spring and L shaped arm together to simplify re-installation and put it in a safe place. 10. Use an appropriately sized punch or screwdriver and hammer to lightly tap the spring pin from the rear of the assembly. Use caution not to damage the spring pin as it is required for installation of the TWM short shifter. Now you can remove the top plastic cap from the assembly, as well as the plastic bushing and o-ring from the top of the stock shifter pivot ball. 11. Remove the 4 bolts which secure the shift assembly to the chassis with a ratchet and 12mm socket and set aside for re-use.

3 12. Once the 4 bolts securing the assembly to the chassis are removed, remove the 4 rubber bushings in the base of the assembly. To do this, push the center steel sleeve from the top down through the rubber bushing. Now, push the rubber bushing down through the bottom of the hole in the assembly while pulling down from the bottom side of the assembly to free the rubber bushing. 13. Place the shifter assembly on its side and remove the shifter from the plastic retainer on the shift rod. This is done by spreading the metal retainer clip until it clears the shifter. Slide the shifter free of the rod and remove from the vehicle. 14. Install the 4 large aluminum bushings beneath the shift assembly in place of the rubber bushings. The bushing s top small diameter goes into the hole that the rubber bushing used to be in. Line up the assembly and bushings with the holes in the chassis. Secure the assembly to the chassis with the stock bolts that were previously in place. 15. Use the cup remover tool included with the kit to remove the plastic cup on the bottom of the original shifter. To do so, place the cup remover tool on top of the open jaws of a vice, the jaws should be approximately 1 apart. Hang the shifter from the tool as shown, be sure the shifter is inserted completely into the slot in the tool. Insert a punch into the center hole through the plastic cup and tap firmly with a hammer to separate the original shifter from cup. Repeat for the second cup on the side arm of the shifter. 16. Install the plastic cups, which you removed from the original shifter onto the TWM shifter. Grease the cups and small pivot balls generously. Place the cup on a firm surface and push the TWM shifter into it until it pops in. 17. Remove the 4 nuts securing the top plastic half of the assembly. Remove the top half of the assembly to expose the 4 studs protruding from the steel base of the assembly.

4 18. Install the 4 small black steel spacers on to the 4 studs. 19. Thread all 4 6 mm coupling nuts on to the 4 studs and tighten with a 10mm socket or wrench. 20. Replace the top plastic half of the assembly on top of the coupling nuts you just installed. Secure the plastic assembly with the 4 6 mm bolts, washers and lock washers provided with the kit in the following manner. Place the 6 mm washer on the hole in the plastic assembly. Now slide the lock washer on to the bolt. Insert the bolt/lock washer combo through the washer and tighten down. The correct order for the bolt/lock washer/washer from the top down is: bolt head on top, lock washer, then washer on the bottom. Tighten down. 21. Lightly grease the large pivot ball on the TWM shifter and install the TWM shifter into the assembly in place of the stock shifter. Push the bottom of the shifter into the plastic cup on the end of the shift cable until the retaining clip pops back into the correct position to hold the plastic cup securely. 22. Replace the plastic and rubber bushing on to the top of the large pivot ball and ensure that the orientation is correct so that the plastic bushing s slot accommodates the side arm on the shifter. Also ensure that the rubber o-ring is seated correctly in the plastic bushing. Replace the top cap of the assembly. With the top cap installed, put the L shaped side arm into position and re-seat the spring into it s correct location with each side of the spring resting on either side of the plastic block on the assembly. 23. Replace the large pin that secures the L shaped arm and ensure that it s orientation is correct. Rotate the pin so that it s flat sides line up with the same shaped hole in the assembly. Once lined up, lightly tapping with a hammer may help the pin slide through to the other side. Now re-install the pin that secures the rear of the top cap in place by lightly tapping it through the assembly with a hammer.

5 24. Drive the clip included with the kit on to the large pin at the front assembly with a 12mm socket to secure it properly against the plastic assembly. Be sure the shaft is pushed all the way into the assembly and the clip is on all the way so there is no free play. You may need to tap the socket with a hammer and apply pressure to the opposite end of the pin to ensure there is no play in the pin. 25. Replace the shift cable on to the L shaped arm and secure with the clip you removed in step Replace both sections of the center console and the shift knob. Now you re ready to drive! Thank you for Choosing: Legal Disclaimer TWM Performance is not responsible for the misuse, incorrect installation, or failure of any product we sell. Under no circumstances, including but not limited to negligence, will TWM Performance be liable for special or consequential damages that result from the use or inability to use our products. TWM Performance does not assume responsibility for any damage to the user, passenger or vehicle resulting from the operation of a TWM Performance product. TO PROTECT USERS FROM INJURY OR DEATH. THE USER ASSUMES ALL RISKS. Autocrossing, track events, and high speed driving are all dangerous activities - always drive responsibly and safely. Warranty Installation of some TWM Performance products may or may not void factory warranties. Always keep OEM equipment that has been replaced in case work is required at the dealer or the vehicle is sold. This warranty covers the original purchasing consumer. This warranty is limited to repair or replacement by TWM Performance of any TWM Performance product that fails because of a defect in materials or workmanship. Warranty does not cover the following: -Damage incurred to related vehicle components -Regular day to day wear on vehicle -Shipping costs for replacements -Installation costs and vehicle down time -Products that have been modified, incorrectly installed or misused. -Mounting hardware and bearings

Installation Manual TWM Performance Short Shift Kit 2006 and up Toyota Yaris

Installation Manual TWM Performance Short Shift Kit 2006 and up Toyota Yaris Installation Manual TWM Performance Short Shift Kit 2006 and up Toyota Yaris 1. Unscrew the shift knob by rotating counter clockwise. 2. Remove the carpet or mat at the bottom of the cup holder at the

More information

95-97 Toyota Tercel & Paseo Short Throw Shifter Installation Manual

95-97 Toyota Tercel & Paseo Short Throw Shifter Installation Manual 95-97 Toyota Tercel & 92-97 Paseo Short Throw Shifter Installation Manual Estimated Installation Time: 40-60 Minutes Tools Required: -Philips head screwdriver and flat head screwdriver -Bench vise -10mm,

More information

Installation Manual Short Shift Kit 2000 and up Toyota Celica 2000 and up MR Spyder

Installation Manual Short Shift Kit 2000 and up Toyota Celica 2000 and up MR Spyder Page 1 Installation Manual Short Shift Kit 2000 and up Toyota Celica 2000 and up MR Spyder 1. Unscrew the shift knob and remove the boot. 2. Remove cover which houses the lighter assembly. There are four

More information

Installation of the Toyota Celica TWM Performance Short Throw Shift Kit Plastic Shifter Assembly

Installation of the Toyota Celica TWM Performance Short Throw Shift Kit Plastic Shifter Assembly Installation of the 1992-1993 Toyota Celica TWM Performance Short Throw Shift Kit Plastic Shifter Assembly Page 1 1. Remove the stock shift knob and boot cover 2. Carefully slide an exacto knife under

More information

Instructions to Install TWM Performance Toyota Celica Turbo 4WD Short Throw Shift Kit

Instructions to Install TWM Performance Toyota Celica Turbo 4WD Short Throw Shift Kit Instructions to Install TWM Performance 1990-1991 Toyota Celica Turbo 4WD Short Throw Shift Kit Page 1 Step 1: Unscrew shift knob and remove console piece with boot. Step 2: Unbolt the seven bolts circled

More information

Toyota Celica Short Throw Shift Kit Installation Manual (Metal Assembly)

Toyota Celica Short Throw Shift Kit Installation Manual (Metal Assembly) 1992-1993 Toyota Celica Short Throw Shift Kit Installation Manual (Metal Assembly) Page 1 1. Remove shift knob and plastic cover from shift assembly. 2. Remove the three nuts holding the top part of the

More information

Installation Manual TWM Performance Short Shift Kit Stage 1 and Stage 2 MazdaSpeed 6

Installation Manual TWM Performance Short Shift Kit Stage 1 and Stage 2 MazdaSpeed 6 Page 1 Installation Manual TWM Performance Short Shift Kit Stage 1 and Stage 2 MazdaSpeed 6 Please Note: It is preferable to park on a flat surface, as you will have to engage and disengage the hand brake

More information

Instructions to Install TWM Performance Toyota Celica Short Throw Shift Kit

Instructions to Install TWM Performance Toyota Celica Short Throw Shift Kit Instructions to Install TWM Performance 1990-1991 Toyota Celica Short Throw Shift Kit Page 1 Step 1: Unscrew shift knob and remove console piece with boot. Step 2: Unbolt the seven bolts circled here (one

More information

Installation Manual TWM Performance Short Shifter 2008 Mitsubishi Lancer

Installation Manual TWM Performance Short Shifter 2008 Mitsubishi Lancer Page 1 Installation Manual TWM Performance Short Shifter 2008 Mitsubishi Lancer Please Note: It is preferable to park on a flat surface, as you will have to engage and disengage the hand brake and shift

More information

2. Disconnect both plastic connectors beneath the rear part of the center console. Note their locations for re-installation.

2. Disconnect both plastic connectors beneath the rear part of the center console. Note their locations for re-installation. Installation Manual TWM Performance Short Shifter 2002 and up Subaru Impreza WRX/RS/TS 1996-2001 Subaru Impreza 2004 and Up Saab 9-2X 1996-2001 Subaru Legacy 1997-2004 Subaru Forester 1. Open the center

More information

Installation Manual TWM Performance Kia Forte Short Shifter

Installation Manual TWM Performance Kia Forte Short Shifter Installation Manual TWM Performance Kia Forte 2009+ Short Shifter Begin the installation by parking on a flat surface, as you will have to engage and disengage the hand brake and shift from gears to neutral.

More information

Installation Manual TWM Performance Full replacement short shifter assembly Civic all trims and models

Installation Manual TWM Performance Full replacement short shifter assembly Civic all trims and models Installation Manual TWM Performance Full replacement short shifter assembly 2006+ Civic all trims and models Begin the installation by parking on a flat surface, as you will have to engage and disengage

More information

Installation Manual TWM Performance Short Shifter Subaru Forester up to 2005

Installation Manual TWM Performance Short Shifter Subaru Forester up to 2005 - 1 - Installation Manual TWM Performance Short Shifter Subaru Forester up to 2005 Please Note: It is preferable to park on a flat surface, as you will have to engage and disengage the hand brake and shift

More information

Installation Manual TWM Performance Short Shift Kit 2003 And Up Saturn Ion

Installation Manual TWM Performance Short Shift Kit 2003 And Up Saturn Ion Installation Manual TWM Performance Short Shift Kit 2003 And Up Saturn Ion It s preferable to park on a flat surface, as you may have to engage and disengage the hand brake and shift from gears to neutral.

More information

Installation Manual TWM Performance Honda Accord 2008+

Installation Manual TWM Performance Honda Accord 2008+ Installation Manual TWM Performance Honda Accord 2008+ Begin the installation by parking on a flat surface, as you will have to engage and disengage the hand brake and shift from gears to neutral. If you

More information

Installation Manual TWM Performance Short Shifter Cobalt SS/SC, SS/TC, HHR SS, Ion Redline and Saab 9-3

Installation Manual TWM Performance Short Shifter Cobalt SS/SC, SS/TC, HHR SS, Ion Redline and Saab 9-3 Page 1 Installation Manual TWM Performance Short Shifter Cobalt SS/SC, SS/TC, HHR SS, Ion Redline and Saab 9-3 Please Note: It is preferable to park on a flat surface, as you will have to engage and disengage

More information

Installation Manual TWM Performance Short Shift Kit Estimated Installation Time: Tools required:

Installation Manual TWM Performance Short Shift Kit Estimated Installation Time: Tools required: Page 1 Installation Manual TWM Performance Short Shift Kit 1993-2001 Nissan Altima 1991-2001 Infiniti G20 1991-2001 Nissan Sentra- 200SX 1991-1993 Nissan NX 1986-1989 Nissan Stanza 1995-2001 Nissan Maxima

More information

Installation Manual TWM Performance Short Shifter Nissan 350Z, 370Z Infiniti G35, G37

Installation Manual TWM Performance Short Shifter Nissan 350Z, 370Z Infiniti G35, G37 Installation Manual TWM Performance Short Shifter Nissan 350Z, 370Z Infiniti G35, G37 It is preferable to park on a flat surface, as you will have to engage and disengage the hand brake and shift from

More information

Installation Manual TWM Performance 2010 Mazda 3 short shifter 5 and 6 speed non-mazdaspeed

Installation Manual TWM Performance 2010 Mazda 3 short shifter 5 and 6 speed non-mazdaspeed Installation Manual TWM Performance 2010 Mazda 3 short shifter 5 and 6 speed non-mazdaspeed Begin the installation by parking on a flat surface, as you will have to engage and disengage the hand brake

More information

Installation Manual TWM Performance Short Shifter Subaru STi 2008+

Installation Manual TWM Performance Short Shifter Subaru STi 2008+ - 1 - Installation Manual TWM Performance Short Shifter Subaru STi 2008+ Please Note: It is preferable to park on a flat surface, as you will have to engage and disengage the hand brake and shift from

More information

Installation Manual TWM Performance Toyota GT86 / Scion FRS / Subaru BRZ Direct Replacement Short Shifter

Installation Manual TWM Performance Toyota GT86 / Scion FRS / Subaru BRZ Direct Replacement Short Shifter Installation Manual TWM Performance Toyota GT86 / Scion FRS / Subaru BRZ Direct Replacement Short Shifter Begin the installation by parking on a flat surface, place wooden blocks in front or behind the

More information

Installation Manual TWM Performance Shift Boot 2006 and up Honda Civic Si

Installation Manual TWM Performance Shift Boot 2006 and up Honda Civic Si Page 1 Installation Manual TWM Performance Shift Boot 2006 and up Honda Civic Si Begin the installation by parking on a flat surface, as you may have to engage and disengage the hand brake and shift from

More information

Installation Manual TWM Performance Chevrolet Camaro 5 th Gen Short Shifter

Installation Manual TWM Performance Chevrolet Camaro 5 th Gen Short Shifter Installation Manual TWM Performance Chevrolet Camaro 5 th Gen Short Shifter Begin the installation by parking on a flat surface, place wooden blocks in front or behind the wheels to prevent the car from

More information

Installation Manual TWM Performance Chevrolet Camaro 5 th Gen Full Replacement Short Shifter

Installation Manual TWM Performance Chevrolet Camaro 5 th Gen Full Replacement Short Shifter Installation Manual TWM Performance Chevrolet Camaro 5 th Gen Full Replacement Short Shifter Begin the installation by parking on a flat surface, place wooden blocks in front or behind the wheels to prevent

More information

james Barone Racing Aftermarket Parts and Accessories

james Barone Racing Aftermarket Parts and Accessories Page1 james Barone Racing Aftermarket Parts and Accessories 2010 2013 MAZDASPEED 3 Short Throw Shifter Installation Instructions What you will need: Ratchet wrench 6 socket extension 10mm and 13mm socket

More information

Chevrolet Cobalt Short Shifter Installation Manual

Chevrolet Cobalt Short Shifter Installation Manual Chevrolet Cobalt Short Shifter Installation Manual Pull shift boot down on the shifter shaft. Pull up on the shift knob to remove it. It requires some force. Remove the ebrake console, shifter console

More information

JBR Adjustable Short Shift Plate Kit Pre-Installation Instructions. Attaching the stand-off to the Shift Plate

JBR Adjustable Short Shift Plate Kit Pre-Installation Instructions. Attaching the stand-off to the Shift Plate JBR Adjustable Short Shift Plate Kit Pre-Installation Instructions Attaching the stand-off to the Shift Plate 1. With the Shift Plate facing up, insert the male end of the stand-off through the slotted

More information

Subaru 5-Speed Double Adjustable Short Throw Shifter

Subaru 5-Speed Double Adjustable Short Throw Shifter Subaru 5-Speed Double Adjustable Short Throw Shifter 1999+ Subaru Impreza 5-Speed 2004-2005 Subaru Forester XT 5-Speed Congratulations on your purchase of the COBB Tuning Double Adjustable Short Throw

More information

Installation Instructions COMPETITION/PLUS SHIFTER Ford Mustang MT82 6-Speed Manual Transmission Catalog#

Installation Instructions COMPETITION/PLUS SHIFTER Ford Mustang MT82 6-Speed Manual Transmission Catalog# Installation Instructions COMPETITION/PLUS SHIFTER 2015-2017 Ford Mustang MT82 6-Speed Manual Transmission Catalog# 3916037 Rev. 00 WORK SAFELY! For maximum safety, perform this installation on a clean,

More information

Installation Instructions INDY SHIFTER Fits: Mustang Fastback & Convertible with MT-82 Transmission Catalog #

Installation Instructions INDY SHIFTER Fits: Mustang Fastback & Convertible with MT-82 Transmission Catalog # Installation Instructions INDY SHIFTER Fits: 2015-2018 Mustang Fastback & Convertible with MT-82 Transmission Catalog # 3916036 Watch our installation video on YouTube WORK SAFELY! For maximum safety,

More information

HURST COMP/PLUS SHIFTER 2015 Ford Mustang (Getrag MT82 six-speed manual transmission) Catalog # by Hurst Performance

HURST COMP/PLUS SHIFTER 2015 Ford Mustang (Getrag MT82 six-speed manual transmission) Catalog # by Hurst Performance FORM 159 0205 07/15 HURST COMP/PLUS SHIFTER 2015 Ford Mustang (Getrag MT82 six-speed manual transmission) Catalog #391 0205 2015 by Hurst Performance Thank you for purchasing the Hurst Comp/Plus Shifter.

More information

Push Start Ignition (05-10 All) Installation

Push Start Ignition (05-10 All) Installation Tools Required: Phillips head screwdriver Flat head screwdriver Ratchet 7mm Socket Torx T20 bit Wire strippers/cutters Hand file Needle nose pliers Installation Instructions: Push Start Ignition (05-10

More information

Steeda S550 MT-82 Tri-Ax Race Short Throw Shifter Installation Instructions For Parts: ,

Steeda S550 MT-82 Tri-Ax Race Short Throw Shifter Installation Instructions For Parts: , Steeda S550 MT-82 Tri-Ax Race Short Throw Shifter Installation Instructions For Parts: 555-7317, 555-7318 Tools required 1. 7mm socket 2. 10mm socket 3. 13mm socket 4. 15mm socket 5. 18mm socket 6. 3/8

More information

PARTS TOOLS. Set Screw. Washer (2) Blue Bushing (2) Black Bushing (2) B&M Short Throw Shifter. Jam Nut Grease. Retaining Ring (2) Insert (2)

PARTS TOOLS. Set Screw. Washer (2) Blue Bushing (2) Black Bushing (2) B&M Short Throw Shifter. Jam Nut Grease. Retaining Ring (2) Insert (2) Installation Instructions SHORT THROW SHIFTER Fits: Porsche Boxter, Boxter S, 911, 996 Cayman & Cayman S models See Application Guide for specific year ranges and engine sizes Catalog # 45135 WORK SAFELY!

More information

INSTALLATION INSTRUCTIONS GM Lower Control Arms P/N 52337, 52437, 52364, 52464, 52319, 52419, 52320, 52420, 52366, 52466, 52368, 52468

INSTALLATION INSTRUCTIONS GM Lower Control Arms P/N 52337, 52437, 52364, 52464, 52319, 52419, 52320, 52420, 52366, 52466, 52368, 52468 INSTALLATION INSTRUCTIONS GM Lower Control Arms P/N 52337, 52437, 52364, 52464, 52319, 52419, 52320, 52420, 52366, 52466, 52368, 52468 TOOLS AND SUPPLIES REQUIRED Floor Jack Jack Stands Wrench Set Hex

More information

Steeda S550 Mustang Street Short Throw Shift Lever Installation Instructions For Part:

Steeda S550 Mustang Street Short Throw Shift Lever Installation Instructions For Part: Steeda S550 Mustang Street Short Throw Shift Lever Installation Instructions For Part: 555-7316 Tools required 1. 7mm socket 2. 10mm socket 3. Small flathead screwdriver 4. T20 torx bit or driver 5. Vise

More information

TK08 TUNING KIT TECHNICAL MANUAL FOR 16/26/27/28 SERIES SHOCKS Revised 6/17/14

TK08 TUNING KIT TECHNICAL MANUAL FOR 16/26/27/28 SERIES SHOCKS Revised 6/17/14 Tech Line: (952) 985-5675 Fax (952) 985-5679 21730 Hanover Ave. Lakeville, MN 55044 www.qa1.net www.facebook.com/qa1motorsports TK08 TUNING KIT TECHNICAL MANUAL CONTENTS UNDER PRESSURE! USE EXTREME CAUTION

More information

James Barone Racing Aftermarket Parts and Accessories

James Barone Racing Aftermarket Parts and Accessories Page1 James Barone Racing Aftermarket Parts and Accessories What you will need: 2014+ Mazda 3, 6 and CX-5 Adjustable Rear Camber Arm Installation Instructions. Jack, jack stands Socket wrench Socket wrench

More information

M-7210-Z3 Focus Short-Throw Shifter (fits 2000-April 2002) INSTALLATION INSTRUCTIONS

M-7210-Z3 Focus Short-Throw Shifter (fits 2000-April 2002) INSTALLATION INSTRUCTIONS Please visit www.fordracingparts.com for the most current instruction information!!! PLEASE READ ALL OF THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION. AT ANY TIME YOU DO NOT UNDERSTAND THE

More information

2014 & up MAZDA 3, 6 and CX5 2.0 & 2.5L Oil Catch Can Installation Instructions

2014 & up MAZDA 3, 6 and CX5 2.0 & 2.5L Oil Catch Can Installation Instructions Page1 James Barone Racing Aftermarket Parts and Accessories 2014 & up MAZDA 3, 6 and CX5 2.0 & 2.5L Oil Catch Can Installation Instructions Tooling: Jack Jack stands or ramps Ratchet wrench 3 extension

More information

Sachs shock manual. ( ) 2 & 4 Stroke RR Enduro. ( ) RS Dual Sport

Sachs shock manual. ( ) 2 & 4 Stroke RR Enduro. ( ) RS Dual Sport Sachs shock manual (2013 2015) 2 & 4 Stroke RR Enduro (2014-2015) RS Dual Sport 1 Introduction The procedures in this manual must take place in a clean environment using professional tools and some specific,

More information

2. Remove front wheels.

2. Remove front wheels. 1 PARTS DIAGRAM 2 Installation Instructions: (PASSENGER SIDE) 1. Place jack under center of RUV front end and lift until front wheels clear the ground. Be careful to support the RUV properly so that it

More information

INSTALLATION GUIDE CRF150R Manual Revision:

INSTALLATION GUIDE CRF150R Manual Revision: REKLUSE MOTOR SPORTS The z-start Pro Clutch INSTALLATION GUIDE CRF150R 191-810 Manual Revision: 032508 2002 Rekluse Motor Sports Rekluse Motor Sports, Inc. 110 E. 43rd Street Boise, Idaho 83714 208-426-0659

More information

M GT 2005 up Mustang ENGINE START Push-Button INSTRUCTION SHEET

M GT 2005 up Mustang ENGINE START Push-Button INSTRUCTION SHEET Please contact the Ford Racing Techline for the most current instruction information @ (800) FORD-788!!! PLEASE READ THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION!!! OVERVIEW: The following

More information

TK08 TUNING KIT TECHNICAL MANUAL FOR 16/26/27/28 SERIES SHOCKS Revised 6/25/14 Tech Line: (952) Fax (952)

TK08 TUNING KIT TECHNICAL MANUAL FOR 16/26/27/28 SERIES SHOCKS Revised 6/25/14 Tech Line: (952) Fax (952) Tech Line: (952) 985-5675 Fax (952) 985-5679 21730 Hanover Ave. Lakeville, MN 55044 www.qa1.net www.facebook.com/qa1motorsports TK08 TUNING KIT TECHNICAL MANUAL CONTENTS UNDER PRESSURE! USE EXTREME CAUTION

More information

Installation Instructions Short Throw Shifter

Installation Instructions Short Throw Shifter Installation Instructions Short Throw Shifter 1996-1999 VW Golf VR6 1998-1999 VW eetle 1998-1999 VW Jetta/ora VR6 Part Number 45106 2001 by &M Racing and Performance Products LLC This &M Short Throw Shifter

More information

Steeda S550 Mustang Street Short Throw Shift Lever Installation Instructions: &

Steeda S550 Mustang Street Short Throw Shift Lever Installation Instructions: & Steeda S550 Mustang Street Short Throw Shift Lever Installation Instructions: 555-7316 & 555-7322 Tools required 1. 7mm socket 2. 10mm socket 3. Small flathead screwdriver 4. T20 torx bit or driver 5.

More information

ADVANCE ADAPTERS INC. P/N: JEEP TJ & (XJ 84-01) ATLAS 4 SPEED CABLE SHIFTER units built after 5/1/12

ADVANCE ADAPTERS INC. P/N: JEEP TJ & (XJ 84-01) ATLAS 4 SPEED CABLE SHIFTER units built after 5/1/12 Paso Robles, CA 93447 PAGE 1 OF 9 Telephone: (800) 350-2223 Fax: (805) 238-4201 Page Rev. Date: 05-12-15 KIT CONSISTS OF: No. Qty Part No. Description 1 1 302051 BASE- TWIN STICK MOUNT 2 1 302080 STUD

More information

Technical Support Line: (952) Fax Line: (952) Hanover Ave. Lakeville, MN

Technical Support Line: (952) Fax Line: (952) Hanover Ave. Lakeville, MN Technical Support Line: (952) 985-5675 Fax Line: (952) 985-5679 21730 Hanover Ave. Lakeville, MN 55044 www.qa1.net INSTALLATION INSTRUCTIONS QA1 P/N CC104MU Camber Caster Plates 1994-2004 Mustang 5.0/4.6

More information

Suzuki Samurai 6.5 Transfer Case Gear Kit, KIT

Suzuki Samurai 6.5 Transfer Case Gear Kit, KIT Suzuki Samurai 6.5 Transfer Case Gear Kit, 105004-3-KIT Kit Contents: Gear, 26 Spline/26 Tooth 1.0 Gear, 44 Tooth 1.0 Gear, 58 Tooth/23 Tooth 1.0 Gear, 67 Tooth/ 27 Tooth 1.0 Counter Shaft 1.0 Counter

More information

CERTAIN MODEL YEAR FUSION AND ESCAPE VEHICLES EQUIPPED WITH A 6F35 TRANSMISSION SHIFTER CABLE BUSHING REPLACEMENT

CERTAIN MODEL YEAR FUSION AND ESCAPE VEHICLES EQUIPPED WITH A 6F35 TRANSMISSION SHIFTER CABLE BUSHING REPLACEMENT PAGE 1 OF 9 CERTAIN 2013-2016 MODEL YEAR FUSION AND 2013-2014 ESCAPE VEHICLES EQUIPPED WITH A 6F35 TRANSMISSION SHIFTER CABLE BUSHING REPLACEMENT OVERVIEW In some of the affected vehicles, the bushing

More information

NOTICE- THIS K-MEMBER REQUIRES THE USE OF COIL OVER SUSPENSION. K-MEMBER WILL NOT WORK WITH FACTORY STYLE SPRINGS.

NOTICE- THIS K-MEMBER REQUIRES THE USE OF COIL OVER SUSPENSION. K-MEMBER WILL NOT WORK WITH FACTORY STYLE SPRINGS. Technical Support Line: (952) 985-5675 Email: Info@QA1.net 21730 Hanover Ave. Lakeville, MN 55044 www.qa1.net INSTALLATION INSTRUCTIONS MUSTANG K-MEMBER P/N MUK11, MUK12, MUK13 NOTICE- THIS K-MEMBER REQUIRES

More information

INSTALLATION GUIDE. KTM 125, 144, Stroke KTM 250, Stroke KTM 250 SXF, XC, XC-W KTM 450, 505 SXF Manual Revision:

INSTALLATION GUIDE. KTM 125, 144, Stroke KTM 250, Stroke KTM 250 SXF, XC, XC-W KTM 450, 505 SXF Manual Revision: REKLUSE MOTOR SPORTS The z-start Pro Clutch INSTALLATION GUIDE KTM 125, 144, 200 2-Stroke KTM 250, 300 2-Stroke KTM 250 SXF, XC, XC-W KTM 450, 505 SXF 191-836 Manual Revision: 050307 2002 Rekluse Motor

More information

Installation Instructions HURST COMPETITION AND BILLET/PLUS SHIFTER Mustang w/5-speed Manual Transmission (GT only)

Installation Instructions HURST COMPETITION AND BILLET/PLUS SHIFTER Mustang w/5-speed Manual Transmission (GT only) Installation Instructions HURST COMPETITION AND BILLET/PLUS SHIFTER 2005-2010 Mustang w/5-speed Manual Transmission (GT only) Catalog# 3915201 WORK SAFELY! For maximum safety, perform this installation

More information

JEEP TJ & (XJ 84-01) ATLAS 2 SP.

JEEP TJ & (XJ 84-01) ATLAS 2 SP. KIT CONSISTS OF: No. Qty Part No. Description 4320 Aerotech Center Way, Page 1 of 9 1 1 302051-RLE BASE- TWIN STICK MOUNT 42RLE 2 1 302080 STUD BOLT 1/2"-13 X 7 (XJ) 3 1 303120 SERRATED LOCK NUT 1/2" X

More information

Trail-Creeper Dual Transfer Case Adapter

Trail-Creeper Dual Transfer Case Adapter Trail-Creeper Dual Transfer Case Adapter Installation Instructions For Kits: 100001-1-KIT 21 Spline 100006-1-KIT 23 Spline KIT Contents: 23 or 21 Spline Coupler 1.0 Adapter Plate w/ Bearings Installed

More information

CorkSport ort Mazda 3 Adjustable Shifter Mazdaspeed 3, Mazda 3 6-speed and Mazda3 SkyActiv 6-speed

CorkSport ort Mazda 3 Adjustable Shifter Mazdaspeed 3, Mazda 3 6-speed and Mazda3 SkyActiv 6-speed Part # Axl-6-963 CorkSport ort Mazda 3 Adjustable Shifter 2010-2013 Mazdaspeed 3, 2010-2013 Mazda 3 6-speed and 2012-2013 Mazda3 SkyActiv 6-speed Pre-Installation Notes: The CorkSport Adjustable Short

More information

Short Shifter Installation Instructions Miata 6-Speed manual

Short Shifter Installation Instructions Miata 6-Speed manual Tools required: 10mm deep socket long extension ratchet small flathead screwdriver phillips-head screwdriver Short Shifter Installation Instructions 2006-14 Miata 6-Speed manual IMPORTANT NOTE: This shifter

More information

Short Shifter Installation Instructions For Miata, 6-speed Manual Transmission

Short Shifter Installation Instructions For Miata, 6-speed Manual Transmission Short Shifter Installation Instructions For 2006-15 Miata, 6-speed Manual Transmission PART# 994-060 Required tools: 10mm deep socket Long extension Ratchet Small flathead screwdriver Phillips-head screwdriver

More information

SPL HICAS ELIMINATOR KIT

SPL HICAS ELIMINATOR KIT SPL HICAS ELIMINATOR KIT Steps to installing the Hicas eliminator kit: 1. Unbolt and remove Hicas actuator. 2. Remove Hicas ball joint and install toe bushing 3. Install Hicas eliminator bracket and toe

More information

James Barone Racing Custom Fabrication of Aftermarket Parts and Accessories Ford Focus ST Rear Engine Mount Installation Instructions

James Barone Racing Custom Fabrication of Aftermarket Parts and Accessories Ford Focus ST Rear Engine Mount Installation Instructions James Barone Racing Custom Fabrication of Aftermarket Parts and Accessories 2013+ Ford Focus ST Rear Engine Mount Installation Instructions Tools Required: Ratchet 6 Extension 13mm 6-Point Socket 15mm

More information

IPSCO STS (Short Throw Shifter) Installation Instructions Dodge Viper WARNING

IPSCO STS (Short Throw Shifter) Installation Instructions Dodge Viper WARNING WARNING Modification of your vehicle with the parts identified above may alter its stock performance; the buyer hereby expressly assumes all risks associated with any such modification. DISCLAIMER OF WARRANTY

More information

Installation Instructions

Installation Instructions Instructions Created by an: Inchworm Tacoma Dual Case Adapter Installation Instructions Suggested Tools: CAUTION: Safety glasses should be worn at all times when working with vehicles and related tools

More information

Installation Instructions

Installation Instructions Instructions Created by an: 2005+ Toyota Tacoma BTB Front Coilovers by Low Range Off Road SKU# TAC-SP-05CO-BTB-650 Diff Drop Kit (SKU# LR-2GDDK) Instructions included Installation Instructions Revised

More information

Installation Instructions

Installation Instructions 86-89 Suzuki Samurai Pedal Rebuild Kit SKU# SIB-PRB! Instructions also includes clutch adjustment procedures. Installation Instructions W e a l s o s u p p l y replacement peddle pads. Click HERE for more

More information

INSTALLATION GUIDE. KTM RFS Husaberg Polaris 450/525 Outlaw KTM 450/525 XC ATV Manual Revision:

INSTALLATION GUIDE. KTM RFS Husaberg Polaris 450/525 Outlaw KTM 450/525 XC ATV Manual Revision: REKLUSE MOTOR SPORTS The z-start Pro Clutch INSTALLATION GUIDE KTM RFS 03-07 Husaberg Polaris 450/525 Outlaw KTM 450/525 XC ATV 191-833 Manual Revision: 010615 2002 Rekluse Motor Sports Rekluse Motor Sports,

More information

Installation Instructions Z-Gate Shifter

Installation Instructions Z-Gate Shifter Installation Instructions Z-Gate Shifter Part Number 80681 1998, 2001 by B&M Racing and Performance Products The B&M Z-Gate shifter can be used in vehicles equipped with most popular three speed automatic

More information

SEAL REPLACEMENT SeaStar ATM, Inboard Steering Cylinders, -3 Models

SEAL REPLACEMENT SeaStar ATM, Inboard Steering Cylinders, -3 Models Copy Part# 343321, Rev. D, 05/2015 Page 1 of 6 SEAL REPLACEMENT SeaStar ATM, Inboard Steering Cylinders, -3 Models CAUTION Applicable Cylinders Throughout this publication, Warnings and Cautions (accompanied

More information

INSTALLATION GUIDE. Kawasaki KLR Manual Revision:

INSTALLATION GUIDE. Kawasaki KLR Manual Revision: REKLUSE MOTOR SPORTS The z-start Pro Clutch INSTALLATION GUIDE Kawasaki KLR650 191-640 Manual Revision: 030308 2007 Rekluse Motor Sports Rekluse Motor Sports, Inc. 110 E. 43rd Street Boise, Idaho 83714

More information

Installation Instructions

Installation Instructions Instructions Created by an: Inchworm Gear Clockable Toyota Dual Transfer Case Adapter Kit, 21 or 23 Spline SKU# TCASE-IW-300-000 Installation Instructions CAUTION: Safety glasses should be worn at all

More information

Tru-Billet Climate Control Knob Installation Instructions

Tru-Billet Climate Control Knob Installation Instructions P/N S197-525-07 2007-08 Tru-Billet Climate Control Knob Installation Instructions Thank you for your purchase of SilverHorse Racing products. Please read all directions before beginning the installation.

More information

Step 4: Remove rear fuel line banjo bolt. Be sure to catch copper washer between pump and front of the rear fuel line.

Step 4: Remove rear fuel line banjo bolt. Be sure to catch copper washer between pump and front of the rear fuel line. Denny T AFC Delete Installation Instructions Tools Needed: 10mm Wrench, 13mm Wrench, 12mm Wrench, 14mm Wrench, 17mm Wrench 5mm Ball End Allen Wrench, 8mm Allen Wrench Needle Nose Pliers, Hammer, Small

More information

16K and 19K Sidewinder TM Service Kit Instructions 86005

16K and 19K Sidewinder TM Service Kit Instructions 86005 86005 Equipment Required: Wrenches: 15/16, 1 1/8, Torque Wrench, Rubber Mallet Included Service Kit Items: 1 Qty. (1) Wear Plate 2 Qty. (6) 5/8 Conical Washer 3 Qty. (2) Wedge Bolt, 5/8-11 X 1 3/4 GRD

More information

C6 (includingg Z06) Catalog # 45034

C6 (includingg Z06) Catalog # 45034 Installation Instructionss Precision Sport Shifter Fits: 2008-20133 Corvette C6 (includingg Z06) Catalog # 45034 WORK SAFELY! For maximum safety, perform this installation on a clean, level surface and

More information

JBR MAZDASPEED

JBR MAZDASPEED Page1 james Barone Racing Aftermarket Parts and Accessories JBR 2007 2009 MAZDASPEED 3 Front Mount Intercooler Piping Kit Installation Instructions for TR8 Intercooler Tooling: o Jack, Jack Stands, Ramps

More information

INSTALLATION GUIDE. Clutch Cable Actuated Models Manual Revision:

INSTALLATION GUIDE. Clutch Cable Actuated Models Manual Revision: REKLUSE MOTOR SPORTS The z-start Pro Clutch INSTALLATION GUIDE Clutch Cable Actuated Models 191-800 Manual Revision: 041513 2012 Rekluse Motor Sports Rekluse Motor Sports, Inc. 12000 W Franklin Rd. Boise,

More information

INSTALLATION GUIDE. Clutch Cable Actuated Models Manual Revision:

INSTALLATION GUIDE. Clutch Cable Actuated Models Manual Revision: REKLUSE MOTOR SPORTS The z-start Pro Clutch INSTALLATION GUIDE Clutch Cable Actuated Models 191-800 Manual Revision: 061810 2002 Rekluse Motor Sports Rekluse Motor Sports, Inc. 110 E. 43rd Street Boise,

More information

5 th Airborne Sidewinder Service Kit Instructions 94316

5 th Airborne Sidewinder Service Kit Instructions 94316 94316 Equipment Required: Wrenches: 15/16, Torque Wrench, Rubber Mallet 3 4 5 2 Included Service Kit Items: 1 Qty. (1) Wear Plate 2 Qty. (1) Wear Bushing 3 Qty. (1) Wear Disc 4 Qty. (4) 5/8-11x2 GRD8 Bolt

More information

Stop! Read This Important Information.

Stop! Read This Important Information. Stop! Read This Important Information. Stop, Do Not Proceed, Read This This door replacement kit is designed for the replacement of doors on a Supertop ONLY! This door will not work on any other style

More information

IPSCO STS (Short Throw Shifter) Installation Instructions (GEN II) Dodge Viper WARNING

IPSCO STS (Short Throw Shifter) Installation Instructions (GEN II) Dodge Viper WARNING WARNING Modification of your vehicle with the parts identified above may alter its stock performance; the buyer hereby expressly assumes all risks associated with any such modification. DISCLAIMER OF WARRANTY

More information

Half Door Installation Instructions

Half Door Installation Instructions Half Door Installation Instructions For: CJ5 (1976-1983) Part Number: 53027 Congratulations on your purchasing decision. Bestop designed these Doors to give you years of dependability and performance with

More information

16K Revolution Service Kit Instructions 86016

16K Revolution Service Kit Instructions 86016 86016 Equipment Required: Wrenches: 15/16, 1 1/8, Torque Wrench, Rubber Mallet Included Service Kit Items: 1 Qty. (1) Wear Plate 2 Qty. (1) Pivot Bushing 3 Qty. (1) Bearing Cup 4 Qty. (1) Bearing 1 5 Qty.

More information

WJ AUTO TRANS. ATLAS SHIFTER

WJ AUTO TRANS. ATLAS SHIFTER KIT CONSISTS OF: No. Qty Part No. Description 4320 Aerotech Center Way, Page 1 of 8 1 1 302051 BASE- ATLAS TWIN STICK MOUNT 2 1 302080 STUD BOLT 1/2-13 X 7 B7 3 1 303120 Serrated-Flange Hex Locknut 1/2-13

More information

2006, 2005 by B&M Racing and Performance Products

2006, 2005 by B&M Racing and Performance Products Installation Instructions Precision Sport Shifter 1997 and up C5 & C6 Chevrolet Corvette (see www.bmracing.com for the latest vehicle fitment applications and model years) Part Number 45044 2006, 2005

More information

INSTALLATION INSTRUCTIONS: LONG TRAVEL KIT 07+ FJ CRUISER and 05+ TACOMA

INSTALLATION INSTRUCTIONS: LONG TRAVEL KIT 07+ FJ CRUISER and 05+ TACOMA INSTALLATION INSTRUCTIONS: LONG TRAVEL KIT 07+ FJ CRUISER and 05+ TACOMA ISNTALLATION DIFFICULTY: Advanced APPROX TIME: 6-8 Hours REQUIRED TOOLS: 14mm-35mm sockets, wrenches, and ratchet 9/16 and 5/8 12

More information

5X Racing Mazda Miata Aluminum Shifter Bushing Installation Instructions

5X Racing Mazda Miata Aluminum Shifter Bushing Installation Instructions 5X Racing Mazda Miata Aluminum Shifter Bushing Installation Instructions Thank you for your purchase! These instructions will explain how to properly install a 5X Racing Aluminum Shifter Bushing in your

More information

INSTALLATION GUIDE Manual Revision:

INSTALLATION GUIDE Manual Revision: REKLUSE MOTOR SPORTS The z-start Pro Clutch INSTALLATION GUIDE KTM 125, 144, 200 2-Stroke KTM 250, 300 2-Stroke KTM 250 SXF, XC, XC-W KTM 400 XC-W KTM 450, 505 SXF, XC-F KTM 450, 530 XCR-W, EXC-R Husaberg

More information

ASSEMBLY INSTRUCTIONS Reese Elite Series FIFTH WHEEL SLIDER HITCH

ASSEMBLY INSTRUCTIONS Reese Elite Series FIFTH WHEEL SLIDER HITCH ASSEMBLY INSTRUCTIONS Reese Elite Series FIFTH WHEEL SLIDER HITCH DEALER/INSTALLER: (1) Provide this Manual to end user. (2) Physically demonstrate procedures in this Manual to end user. (3) Have end user

More information

TJ 231/241 CABLE SHIFTER

TJ 231/241 CABLE SHIFTER KIT CONSISTS OF: # Qty Part No. Description P.O. Box 247, 4320 Aerotech Center Way PAGE 1 OF 10 Page Rev. Date: 08-29-16 1 1 300474 WASHER-RUBBER YOKE SEAL 32 SPLINE 2 1 300476 NUT- 7/8"-20 FLANGE LOCKNUT

More information

INSTALLATION GUIDE. KTM 950/990 LC8 Engine Manual Revision:

INSTALLATION GUIDE. KTM 950/990 LC8 Engine Manual Revision: REKLUSE MOTOR SPORTS The z-start Pro Clutch INSTALLATION GUIDE KTM 950/990 LC8 Engine 191-631 Manual Revision: 071510 2007 Rekluse Motor Sports Rekluse Motor Sports, Inc. 110 E. 43rd Street Boise, Idaho

More information

INSTALLATION INSTRUCTIONS QA1 P/N x400, x500, x600, x400, x500, x F100 Front Coil-over Suspension System

INSTALLATION INSTRUCTIONS QA1 P/N x400, x500, x600, x400, x500, x F100 Front Coil-over Suspension System INSTALLATION INSTRUCTIONS QA1 P/N 52620-x400, 52620-x500, 52620-x600, 52621-x400, 52621-x500, 52621-x600 65-72 F100 Front Coil-over Suspension System TOOLS AND SUPPLIES REQUIRED Floor Jack Two (2) Jack

More information

FRONT DROP SPINDLES

FRONT DROP SPINDLES 92725000 88-98 2 FRONT DROP SPINDLES Thank you for choosing Rough Country for all your suspension needs. Rough Country recommends a certified technician install this system. In addition to these instructions,

More information

Installation Instructions for the EVO3 Height-Adjustable Ultimate Short Shifter

Installation Instructions for the EVO3 Height-Adjustable Ultimate Short Shifter Installation Instructions for the EVO3 Height-Adjustable Ultimate Short Shifter for 1992-2005 325, 323, 318 and 1986-1994 525, 528, 535, 540 5-speed models only. (part number USSE3 and USSE5) Thank you

More information

1989 Jeep Cherokee. STEERING COLUMN' '1989 STEERING Jeep Steering Columns STEERING COLUMN STEERING Jeep Steering Columns

1989 Jeep Cherokee. STEERING COLUMN' '1989 STEERING Jeep Steering Columns STEERING COLUMN STEERING Jeep Steering Columns STEERING COLUMN 1989 STEERING Jeep Steering Columns DESCRIPTION All models use collapsible steering columns. All columns have integral ignition switch and locking device. Optional tilt wheel is available

More information

2014+ Mazda 3/6 & CX-5 Front Sway Bar Installation Instructions

2014+ Mazda 3/6 & CX-5 Front Sway Bar Installation Instructions Page1 James Barone Racing 2014+ Mazda 3/6 & CX-5 Front Sway Bar Installation Instructions Tools Required: Jack & jack stands or a lift Socket wrench 3 and 12 socket extensions 10mm, 14mm, 17mm, 19mm socket

More information

Evora shiftr111 Installation Instructions Rev. B Page 1 of 14

Evora shiftr111 Installation Instructions Rev. B Page 1 of 14 Evora shiftr111 Installation Rev. B Page 1 of 14 READ FITTING INSTRUCTIONS IN FULL BEFORE INSTALLATION This article is sold without warranty expressed or implied. No warranty or representation is made

More information

Installation Instructions

Installation Instructions 2003-Present Toyota 4Runner 2007-2014 FJ Cruiser LRT 3" Lift Kit by Low Range Off-Road (SKU# LR-LRFJ4RU) Installation Instructions Suggested Tools: CAUTION: Safety glasses should be worn at all times when

More information

Installation Instructions Sport Bar Covers

Installation Instructions Sport Bar Covers Installation Instructions Sport Bar Covers Vehicle Application Jeep TJ Wrangler 2003-2006 Part Number: 80022 Jeep TJD Wrangler Unlimited 2004-2006 Part Number: 80023 www.bestop.com - We re here to help!

More information

KJ09168BK Renegade 1.5 Lift Kit

KJ09168BK Renegade 1.5 Lift Kit KJ09168BK Renegade 1.5 Lift Kit www.daystarweb.com Tech Support Contact Info Tech@DaystarWeb.com Phone: 623.907.0081 Fax: 623.907.0088 841 South 71 st Avenue Phoenix, AZ 85043 Instruction Sheet: P21677

More information

JK HD Skid Plate for Rear Falcon Shocks

JK HD Skid Plate for Rear Falcon Shocks 1 JK HD Skid Plate for Rear Falcon Shocks Kit # 36-07-01-300 Important Notes: Prior to beginning this or any installation read these instructions to familiarize yourself with the required steps and evaluate

More information