Installation Manual TWM Performance Chevrolet Camaro 5 th Gen Full Replacement Short Shifter
|
|
- Wesley Carpenter
- 6 years ago
- Views:
Transcription
1 Installation Manual TWM Performance Chevrolet Camaro 5 th Gen Full Replacement Short Shifter Begin the installation by parking on a flat surface, place wooden blocks in front or behind the wheels to prevent the car from moving while you re working. Make sure to let the car cool down before you do the install as you will be working around the shifter assembly, the transmission and the exhaust system. The car will need to be jacked up, only use jack stands Please read this installation manual completely before installing the product. This manual is available for download in color at Estimated Installation Time: minutes Tools required: Ratchet Socket set Allen bit set Ratchet extensions Universal joint Philips head screwdriver Flat head screwdriver Flash light or shop light Shop jack Jack stands
2 2 1. Start by prying the back of the console trim with a flathead screwdriver or a trim tool upwards to unclip it, then run your fingers to the front to unclip the whole trim. You can leave the gauges connected and simply move the whole trim over to the passenger side 2. Unscrew the (4) screws holding the shift boot trim in the console using a Philips screwdriver 3. Remove the shift knob by pulling upwards with some force Set the knob and shift boot aside 4. Loosen, but not remove, the (4) screws holding the shifter assembly to the body using a 10mm socket
3 3 5. Underneath the car, remove the black plate towards the back of the car by taking off (4) screws with a 15mm socket Then slide the exhaust shield towards the back of the car, to do this you may need to remove some body nuts with a 10mm socket 6. Next, the transmission support needs to be taken off, with the same 15mm socket, remove the (4) screws holding the support to the body Remove the screw little by little in a star-like pattern to slowly lower the transmission without putting too much strain on individual screw 7. Completely remove the transmission support by removing the (2) nuts underneath with the same 15mm socket Careful not to drop the support 8. Underneath the car, over the drive shaft, locate the shifter assembly and remove the lower dust boot by pulling out and down on the tabs at each corner
4 4 9. Push the dust boot out of the way to reveal the lower section of the shift rod. With a flathead screwdriver, push out one of the clips on each side of the linkage 10. With your fingers, simply slide the linkage pin out, do not misplace the pin and the clips 11. Remove the (2) screws from under the assembly with a 10mm socket, remove the ring and pull the shifter down and out 12. Locate the forward arm of the shifter carrier on the transmission and using a flat head screwdriver pry the pin s clip off the arm of the carrier, swivel the clip completely off the arm
5 5 13. With the same screwdriver, pry the pin out completely, do to this you will need some help to pull down very hard on the transmission/driveshaft to lower the transmission enough that the pin will clear the body of the car to come out completely This needs to be done on both sides on the transmission on the passenger side of the car, there is even less room 14. Now remove the (2) nuts at the back of the shifter assembly holding the bushing onto the body using a 10mm socket with extensions 15. You can now wiggle the carrier around the exhaust and the drive shaft to take it off the car 16. Take your brand new TWM Performance Caramo 5 th Gen Full Replacement carrier and lubricate all the poly bushings (on the legs and on the pin holder) with the provided tube of grease, then insert it into place and reverse steps 14 to 12.
6 6 17. Before inserting the shifter shaft into the carrier, slide the spacer ring into the carrier all the way up to the top plate 18. Then insert the shifter shaft, having a friend in the car to guide the shaft thru the upper dust boot is very helpful 19. Put the retaining plate into position and screw it in with the provided M8 screws and lock washers with a 5mm Allen bit and extensions Reverse steps 10 to From inside the car, pinch the upper dust boot with your fingers and stretch it till the rounded diamond shape fits over the TWM carrier s top plate If you have purchased a TWM Performance shift knob, now is the perfect time to install it, follow the instructions provided in the knob installation manual Reverse steps 3 to 1
7 7 Thank you for choosing TMW Performance so you can enjoy your 5 th gen Chevrolet Camaro even more!! Legal Disclaimer TWM Performance is not responsible for the misuse, incorrect installation, or failure of any product we sell. If you do not feel confident to properly install the product, please refer to a professionnal Under no circumstances, including but not limited to negligence, will TWM Performance be liable for special or consequential damages that result from the use or inability to use our products. TWM Performance does not assume responsibility for any damage to the user, passenger or vehicle resulting from the operation of a TWM Performance product. TO PROTECT USERS FROM INJURY OR DEATH. THE USER ASSUMES ALL RISKS. Autocrossing, track events, and high speed driving are all dangerous activities - always drive responsibly and safely. Warranty Installation of some TWM Performance products may or may not void factory warranties. Always keep OEM equipment that has been replaced in case work is required at the dealer or the vehicle is sold. This warranty covers the original purchasing consumer. This warranty is limited to repair or replacement by TWM Performance of any TWM Performance product that fails because of a defect in materials or workmanship. Warranty does not cover the following: -Products that have been modified incorrectly or incorrectly installed or misused. -Damage incurred to related vehicle components -Shipping costs for replacements -Regular day to day wear on vehicle -Installation costs and vehicle down time -Mounting hardware and bearings
Installation Manual TWM Performance Chevrolet Camaro 5 th Gen Short Shifter
Installation Manual TWM Performance Chevrolet Camaro 5 th Gen Short Shifter Begin the installation by parking on a flat surface, place wooden blocks in front or behind the wheels to prevent the car from
More informationInstallation Manual TWM Performance Toyota GT86 / Scion FRS / Subaru BRZ Direct Replacement Short Shifter
Installation Manual TWM Performance Toyota GT86 / Scion FRS / Subaru BRZ Direct Replacement Short Shifter Begin the installation by parking on a flat surface, place wooden blocks in front or behind the
More informationInstallation Manual TWM Performance Honda Accord 2008+
Installation Manual TWM Performance Honda Accord 2008+ Begin the installation by parking on a flat surface, as you will have to engage and disengage the hand brake and shift from gears to neutral. If you
More informationInstallation Manual TWM Performance Full replacement short shifter assembly Civic all trims and models
Installation Manual TWM Performance Full replacement short shifter assembly 2006+ Civic all trims and models Begin the installation by parking on a flat surface, as you will have to engage and disengage
More informationInstallation Manual TWM Performance Kia Forte Short Shifter
Installation Manual TWM Performance Kia Forte 2009+ Short Shifter Begin the installation by parking on a flat surface, as you will have to engage and disengage the hand brake and shift from gears to neutral.
More informationInstallation Manual TWM Performance Short Shift Kit 2003 And Up Saturn Ion
Installation Manual TWM Performance Short Shift Kit 2003 And Up Saturn Ion It s preferable to park on a flat surface, as you may have to engage and disengage the hand brake and shift from gears to neutral.
More information2. Disconnect both plastic connectors beneath the rear part of the center console. Note their locations for re-installation.
Installation Manual TWM Performance Short Shifter 2002 and up Subaru Impreza WRX/RS/TS 1996-2001 Subaru Impreza 2004 and Up Saab 9-2X 1996-2001 Subaru Legacy 1997-2004 Subaru Forester 1. Open the center
More informationInstallation Manual TWM Performance Short Shifter Subaru Forester up to 2005
- 1 - Installation Manual TWM Performance Short Shifter Subaru Forester up to 2005 Please Note: It is preferable to park on a flat surface, as you will have to engage and disengage the hand brake and shift
More informationInstallation Manual TWM Performance 2010 Mazda 3 short shifter 5 and 6 speed non-mazdaspeed
Installation Manual TWM Performance 2010 Mazda 3 short shifter 5 and 6 speed non-mazdaspeed Begin the installation by parking on a flat surface, as you will have to engage and disengage the hand brake
More informationInstallation Manual TWM Performance Short Shift Kit Stage 1 and Stage 2 MazdaSpeed 6
Page 1 Installation Manual TWM Performance Short Shift Kit Stage 1 and Stage 2 MazdaSpeed 6 Please Note: It is preferable to park on a flat surface, as you will have to engage and disengage the hand brake
More informationInstallation Manual TWM Performance Short Shifter Nissan 350Z, 370Z Infiniti G35, G37
Installation Manual TWM Performance Short Shifter Nissan 350Z, 370Z Infiniti G35, G37 It is preferable to park on a flat surface, as you will have to engage and disengage the hand brake and shift from
More informationToyota Celica Short Throw Shift Kit Installation Manual (Metal Assembly)
1992-1993 Toyota Celica Short Throw Shift Kit Installation Manual (Metal Assembly) Page 1 1. Remove shift knob and plastic cover from shift assembly. 2. Remove the three nuts holding the top part of the
More informationInstallation Manual TWM Performance Short Shifter 2008 Mitsubishi Lancer
Page 1 Installation Manual TWM Performance Short Shifter 2008 Mitsubishi Lancer Please Note: It is preferable to park on a flat surface, as you will have to engage and disengage the hand brake and shift
More informationInstallation Manual TWM Performance Short Shift Kit 2006 and up Toyota Yaris
Installation Manual TWM Performance Short Shift Kit 2006 and up Toyota Yaris 1. Unscrew the shift knob by rotating counter clockwise. 2. Remove the carpet or mat at the bottom of the cup holder at the
More information95-97 Toyota Tercel & Paseo Short Throw Shifter Installation Manual
95-97 Toyota Tercel & 92-97 Paseo Short Throw Shifter Installation Manual Estimated Installation Time: 40-60 Minutes Tools Required: -Philips head screwdriver and flat head screwdriver -Bench vise -10mm,
More informationInstallation Manual Short Shift Kit 2000 and up Toyota Celica 2000 and up MR Spyder
Page 1 Installation Manual Short Shift Kit 2000 and up Toyota Celica 2000 and up MR Spyder 1. Unscrew the shift knob and remove the boot. 2. Remove cover which houses the lighter assembly. There are four
More informationInstallation of the Toyota Celica TWM Performance Short Throw Shift Kit Plastic Shifter Assembly
Installation of the 1992-1993 Toyota Celica TWM Performance Short Throw Shift Kit Plastic Shifter Assembly Page 1 1. Remove the stock shift knob and boot cover 2. Carefully slide an exacto knife under
More informationInstallation Manual TWM Performance Short Shift Kit Estimated Installation Time: Tools required:
Page 1 Installation Manual TWM Performance Short Shift Kit 1993-2001 Nissan Altima 1991-2001 Infiniti G20 1991-2001 Nissan Sentra- 200SX 1991-1993 Nissan NX 1986-1989 Nissan Stanza 1995-2001 Nissan Maxima
More informationInstructions to Install TWM Performance Toyota Celica Short Throw Shift Kit
Instructions to Install TWM Performance 1990-1991 Toyota Celica Short Throw Shift Kit Page 1 Step 1: Unscrew shift knob and remove console piece with boot. Step 2: Unbolt the seven bolts circled here (one
More informationInstallation Manual TWM Performance Short throw shifter 2001 and up Hyundai Accent
Installation Manual TWM Performance Short throw shifter 2001 and up Hyundai Accent 1. Place the vehicle on a flat surface with blocks in front and behind the wheels preventing unwanted movement. The car
More informationInstallation Manual TWM Performance Short Shifter Cobalt SS/SC, SS/TC, HHR SS, Ion Redline and Saab 9-3
Page 1 Installation Manual TWM Performance Short Shifter Cobalt SS/SC, SS/TC, HHR SS, Ion Redline and Saab 9-3 Please Note: It is preferable to park on a flat surface, as you will have to engage and disengage
More informationInstructions to Install TWM Performance Toyota Celica Turbo 4WD Short Throw Shift Kit
Instructions to Install TWM Performance 1990-1991 Toyota Celica Turbo 4WD Short Throw Shift Kit Page 1 Step 1: Unscrew shift knob and remove console piece with boot. Step 2: Unbolt the seven bolts circled
More informationInstallation Manual TWM Performance Shift Boot 2006 and up Honda Civic Si
Page 1 Installation Manual TWM Performance Shift Boot 2006 and up Honda Civic Si Begin the installation by parking on a flat surface, as you may have to engage and disengage the hand brake and shift from
More informationInstallation Manual TWM Performance Short Shifter Subaru STi 2008+
- 1 - Installation Manual TWM Performance Short Shifter Subaru STi 2008+ Please Note: It is preferable to park on a flat surface, as you will have to engage and disengage the hand brake and shift from
More informationSteeda S550 Mustang Street Short Throw Shift Lever Installation Instructions For Part:
Steeda S550 Mustang Street Short Throw Shift Lever Installation Instructions For Part: 555-7316 Tools required 1. 7mm socket 2. 10mm socket 3. Small flathead screwdriver 4. T20 torx bit or driver 5. Vise
More informationChevrolet Cobalt Short Shifter Installation Manual
Chevrolet Cobalt Short Shifter Installation Manual Pull shift boot down on the shifter shaft. Pull up on the shift knob to remove it. It requires some force. Remove the ebrake console, shifter console
More informationjames Barone Racing Aftermarket Parts and Accessories
Page1 james Barone Racing Aftermarket Parts and Accessories 2010 2013 MAZDASPEED 3 Short Throw Shifter Installation Instructions What you will need: Ratchet wrench 6 socket extension 10mm and 13mm socket
More informationBarton Short Throw Shifter 11/12 V6, GT Mustang:
Barton Short Throw Shifter 11/12 V6, GT Mustang: Tools Required: 10mm deep socket Socket wrench 10 extension for socket wrench Jack Jack stand Small piece of wood Small hook tool (recommended) *can be
More informationSteeda S550 Mustang Street Short Throw Shift Lever Installation Instructions: &
Steeda S550 Mustang Street Short Throw Shift Lever Installation Instructions: 555-7316 & 555-7322 Tools required 1. 7mm socket 2. 10mm socket 3. Small flathead screwdriver 4. T20 torx bit or driver 5.
More informationFord Mustang V6 OEM-Style Fog Light Kit Parts List: Quantity: Tool List:
2015-2017 Ford Mustang V6 OEM-Style Fog Light Kit Parts List: Quantity: Tool List: LED Foglights/ Bezels 2 Flat head & Phillips screwdriver (if you ordered part#3600) Ratchet & Socket set OR Wiring harness
More information2014 & up MAZDA 3, 6 and CX5 2.0 & 2.5L Oil Catch Can Installation Instructions
Page1 James Barone Racing Aftermarket Parts and Accessories 2014 & up MAZDA 3, 6 and CX5 2.0 & 2.5L Oil Catch Can Installation Instructions Tooling: Jack Jack stands or ramps Ratchet wrench 3 extension
More informationJames Barone Racing Aftermarket Parts and Accessories
Page1 James Barone Racing Aftermarket Parts and Accessories What you will need: 2014+ Mazda 3, 6 and CX-5 Adjustable Rear Camber Arm Installation Instructions. Jack, jack stands Socket wrench Socket wrench
More informationInstallation Instructions HURST COMPETITION AND BILLET/PLUS SHIFTER Mustang w/5-speed Manual Transmission (GT only)
Installation Instructions HURST COMPETITION AND BILLET/PLUS SHIFTER 2005-2010 Mustang w/5-speed Manual Transmission (GT only) Catalog# 3915201 WORK SAFELY! For maximum safety, perform this installation
More informationPARTS LIST INSTALLATION INSTRUCTIONS PARTS LIST AND INSTALLATION GUIDE INSTALL TIME: 2 HOURS INSTALL DIFFICULTY: 3/5
PARTS LIST AND PARTS LIST 1PC MISHIMOTO INTERCOOLER 1PC M6 X 1.0 X 20MM FLANGE BOLT 1PC M4 X 0.7 X 12MM BUTTON-HEAD BOLT 1PC M4 LOCK WASHER 1PC MAP SENSOR O-RING 2. Remove the eight pop clips that hold
More informationJames Barone Racing Custom Fabrication of Aftermarket Parts and Accessories Mazda 3 and MAZDASPEED 3 Mud Flap Installation Instructions
James Barone Racing Custom Fabrication of Aftermarket Parts and Accessories 2010+ Mazda 3 and MAZDASPEED 3 Mud Flap Installation Instructions To protect and avoid damage to your new JBR Mud Flaps care
More informationCorkSport AluminumShift Knob Mazda's with manual transmissions.
CorkSport AluminumShift Knob 2014+ Mazda's with manual transmissions. Thank you for purchasing the CorkSport Mazda Aluminum Shift Knob. Adjustable weights to adjust your throw, increase the response and
More informationSubaru 5-Speed Double Adjustable Short Throw Shifter
Subaru 5-Speed Double Adjustable Short Throw Shifter 1999+ Subaru Impreza 5-Speed 2004-2005 Subaru Forester XT 5-Speed Congratulations on your purchase of the COBB Tuning Double Adjustable Short Throw
More informationJBR Mazda 3 & Mazdaspeed 3 Adjustable Rear Camber Arm Installation Instructions
james Barone Racing Aftermarket Parts and Accessories JBR 2004 2013 Mazda 3 & Mazdaspeed 3 Adjustable Rear Camber Arm Installation Instructions Tooling: Jack and jack stands Ratchet wrench 17mm socket
More information2012 and up Ford Focus ST Valve Cover Oil Catch Can Installation Instructions
Page1 James Barone Racing Aftermarket Parts and Accessories 2012 and up Ford Focus ST Valve Cover Oil Catch Can Installation Instructions Tooling: Jack, Jack Stands or ramps Ratchet Short extension 8mm
More informationInstallation Instructions BILLET/PLUS PISTOL-GRIP SHIFTER Fits: 2016 Camaro V6 with Manual Transmission Catalog #
Installation Instructions BILLET/PLUS PISTOL-GRIP SHIFTER Fits: 2016 Camaro V6 with Manual Transmission Catalog # 3916034 WORK SAFELY! For maximum safety, perform this installation on a clean, level surface
More informationSteeda S550 MT-82 Tri-Ax Race Short Throw Shifter Installation Instructions For Parts: ,
Steeda S550 MT-82 Tri-Ax Race Short Throw Shifter Installation Instructions For Parts: 555-7317, 555-7318 Tools required 1. 7mm socket 2. 10mm socket 3. 13mm socket 4. 15mm socket 5. 18mm socket 6. 3/8
More informationHybrid Racing Civic Si Shifter Cables
Hybrid Racing 06-11 Civic Si Shifter Cables Install Guide This product may not be legal for highway use. Hybrid Racing is not responsible for any direct or indirect, actual or incidental expense attributed
More informationShort Shifter Installation Instructions Miata 6-Speed manual
Tools required: 10mm deep socket long extension ratchet small flathead screwdriver phillips-head screwdriver Short Shifter Installation Instructions 2006-14 Miata 6-Speed manual IMPORTANT NOTE: This shifter
More informationJames Barone Racing Aftermarket Parts and Accessories Ford Focus ST Front Sway Bar Installation Instructions. Page1
Page1 James Barone Racing Aftermarket Parts and Accessories 2013+ Ford Focus ST Front Sway Bar Installation Instructions Tools Required: Jack Lift or ramps Ratchet wrench Torque Wrench 6 and 12 Extension
More information2014+ Mazda 3/6 & CX-5 Front Sway Bar Installation Instructions
Page1 James Barone Racing 2014+ Mazda 3/6 & CX-5 Front Sway Bar Installation Instructions Tools Required: Jack & jack stands or a lift Socket wrench 3 and 12 socket extensions 10mm, 14mm, 17mm, 19mm socket
More informationMAZDASPEED 3 JBR Oil Catch Can VTA Kit Installation Instructions
James Barone Racing Aftermarket Parts and Accessories 07-2013 MAZDASPEED 3 JBR Oil Catch Can VTA Kit Installation Instructions These installation instructions are written assuming you already have a JBR
More informationMINI Smartphone Mount Pro Series Ver 1.1 CRMC-1000-R130. Instructions for both the XL Scissor and XXL Clamshell Cradles for Gen 2 MINIs.
MINI Smartphone Mount Pro Series Ver 1.1 CRMC-1000-R130 Instructions for both the XL Scissor and XXL Clamshell Cradles for Gen 2 MINIs 1 of 5 Overview XL Scissor and XXL Clamshell Cradles for Gen 2 MINIs
More information2017 Current Ford Raptor HoneyBadger Rear Bumper Installation Instructions
2017 Current Ford Raptor HoneyBadger Rear Bumper Installation Instructions PREPARATION 1. Disconnect the negative terminal on the battery. Park the vehicle on level ground and set the emergency brake.
More informationInstallation Instructions for the EVO3 Height-Adjustable Ultimate Short Shifter. for F80 M3 and F82 M4
Installation Instructions for the EVO3 Height-Adjustable Ultimate Short Shifter for 2013+ F80 M3 and F82 M4 part number USSF80 Thank you for purchasing the Ultimate Shift Kit. Please read these directions
More informationSubaru WRX Performance Charge-Pipe System, 2015+
PARTS LIST AND PARTS LIST 1PC BAR-AND-PLATE INTERCOOLER 1PC INTERCOOLER MOUNTING BRACKET 1PC CHARGE-PIPE ASSEMBLY 1PC AIR DIVERTER WITH ATTACHED RUBBER GASKETS 1PC CHARGE-PIPE-TO-INTERCOOLER HOSE INSTALLATION
More informationJBR Adjustable Short Shift Plate Kit Pre-Installation Instructions. Attaching the stand-off to the Shift Plate
JBR Adjustable Short Shift Plate Kit Pre-Installation Instructions Attaching the stand-off to the Shift Plate 1. With the Shift Plate facing up, insert the male end of the stand-off through the slotted
More informationROUSH Short Throw Shifter Kit
ROUSH Short Throw Shifter Kit Part Number 1310R7400 Application: 2010 Ford Mustang GT Installation Instructions Before installing your ROUSH Performance Product(s), read through the entire installation
More informationJBR MAZDASPEED
Page1 james Barone Racing Aftermarket Parts and Accessories JBR 2007 2009 MAZDASPEED 3 Front Mount Intercooler Piping Kit Installation Instructions for TR8 Intercooler Tooling: o Jack, Jack Stands, Ramps
More informationJames Barone Racing Custom Fabrication of Aftermarket Parts and Accessories Ford Focus ST Rear Engine Mount Installation Instructions
James Barone Racing Custom Fabrication of Aftermarket Parts and Accessories 2013+ Ford Focus ST Rear Engine Mount Installation Instructions Tools Required: Ratchet 6 Extension 13mm 6-Point Socket 15mm
More informationCognito Motorsports 2014 Polaris RZR XP1000 2/4 seat Tie Rod Kit *Installation Instructions*
Cognito Motorsports 2014 Polaris RZR XP1000 2/4 seat Tie Rod Kit *Installation Instructions* For long travel and stock width kit #s: 360-90021 and 360-90060 Introduction - Installation requires a qualified
More informationToggle Button Kit. Installation Instructions MK5 / MK6 Golf, MK5 Jetta
Toggle Button Kit Installation Instructions MK5 / MK6 Golf, MK5 Jetta Thank you for choosing the Double Apex Toggle Button kit. If you have any questions about the installation please do not hesitate to
More informationInstallation Instructions COMPETITION/PLUS SHIFTER Ford Mustang MT82 6-Speed Manual Transmission Catalog#
Installation Instructions COMPETITION/PLUS SHIFTER 2015-2017 Ford Mustang MT82 6-Speed Manual Transmission Catalog# 3916037 Rev. 00 WORK SAFELY! For maximum safety, perform this installation on a clean,
More informationIPSCO STS (Short Throw Shifter) Installation Instructions Dodge Viper WARNING
WARNING Modification of your vehicle with the parts identified above may alter its stock performance; the buyer hereby expressly assumes all risks associated with any such modification. DISCLAIMER OF WARRANTY
More informationPlease read BOTH these Installation Instructions and the General Information sheet prior to installing or operating this equipment.
Attachment Tab Height: 24-1/4 Serial Number Attachment Tab Width: 24 Please read BOTH these and the General Information sheet prior to installing or operating this equipment. 1. Blue Ox towing products
More informationShort Shifter Installation Instructions For Miata, 6-speed Manual Transmission
Short Shifter Installation Instructions For 2006-15 Miata, 6-speed Manual Transmission PART# 994-060 Required tools: 10mm deep socket Long extension Ratchet Small flathead screwdriver Phillips-head screwdriver
More informationBD POWER SHORT SHIFTER Dodge Speed Dodge Speed Dodge Speed.
June 05 Cummins Short Shift Kit (1031050/1031055/103156) 1 BD POWER SHORT SHIFTER for Dodge Cummins 1998-2005 Manual Transmissions Application Chart 1031056 Dodge 1998-2002 5 Speed 1031050 Dodge 2000-2002
More informationTechnical Support (707)
Installation Instructions CONSOLE MEGASHIFTER Fits: 1982-1992 Camaro & Firebird w/automatic Transmission *except 1988-1992 Firebird Formula Model Catalog # 80692 WORK SAFELY! For maximum safety, perform
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS BMW S1000RR 2015+ TracStar Replacement Handlebars P/N: TS05099 IMPORTANT: PLEASE GIVE CUSTOMER ENCLOSED INFORMATION! Thank you for your purchase of our HeliBars. They are designed
More informationInstallation Instructions
Suzuki Samurai 1 Inch and 2 Inch Body Lift Kit (SKU# SSP-BL) Installation Instructions Background: These instructions are designed for installing the 2 body lift. Our approach is to raise the entire body
More information57-1. Front door. Tools. Special tools and equipment. T Socket 3320/2 Bit insert for Socket T Assembly tool
57-1 Front door Tools Special tools and equipment T 10011 Socket 3320/2 Bit insert for 3320 3410 Socket T 10034 Assembly tool 57-2 Front door, assembly overview Note: The instrument panel must be removed
More informationHurst Billet Competition Plus Shifter - TR-3650 (05-10 GT) Installed in: 2010 Ford Mustang GT
Tools Required: Socket Ratchet 10 mm Wrench/Socket 10 mm Deep Socket 13 mm Wrench/Socket Socket Extension Flat Head Screw Driver WD-40 Hurst Billet Competition Plus Shifter - TR-3650 (05-10 GT) Installed
More informationInstallation Instructions QUICKSILVER CONSOLE SHIFTER Fits: Chevelle / El Camino
WORK SAFELY! For maximum safety, perform this installation on a clean, level surface and with the engine turned off. Place blocks or wedges in front of and behind both rear wheels to prevent movement in
More informationChrome Upper Stick. Catalog# product too your PARTS
Installation Instructionss HURST COMPETITION/PLUS SHIFTER 2011-2014 Ford Mustang Getrag MT82 6-Speed Manual Transmission Catalog# 3916039 02/14/17 WORK SAFELY! For maximum safety, perform this installation
More informationHURST COMP/PLUS SHIFTER 2015 Ford Mustang (Getrag MT82 six-speed manual transmission) Catalog # by Hurst Performance
FORM 159 0205 07/15 HURST COMP/PLUS SHIFTER 2015 Ford Mustang (Getrag MT82 six-speed manual transmission) Catalog #391 0205 2015 by Hurst Performance Thank you for purchasing the Hurst Comp/Plus Shifter.
More informationInstallation Instructions
Instructions Created by an: 2005+ Toyota Tacoma BTB Front Coilovers by Low Range Off Road SKU# TAC-SP-05CO-BTB-650 Diff Drop Kit (SKU# LR-2GDDK) Instructions included Installation Instructions Revised
More informationInstallation Instructions HURST BILLET COMPETITION/PLUS SHIFTER Dodge Challenger
Installation Instructions HURST BILLET COMPETITION/PLUS SHIFTER 2009-2015 Dodge Challenger Catalog #3916020 WORK SAFELY! For maximum safety, perform this installation on a clean, level surface and with
More informationCOLD AIR INTAKE INSTALLATION INSTRUCTIONS PART NUMBER D A. APPLICATION: E36/7 M-Roadster or M-Coupe 3.
COLD AIR INTAKE INSTALLATION INSTRUCTIONS PART NUMBER D760-0323A APPLICATION: 1998-00 E36/7 M-Roadster or M-Coupe 3.2 Liter PARTS LIST Air Filter Assembly 3 1/2" Tube Intake Shield Silicone Hose Airflow
More informationIPSCO STS (Short Throw Shifter) Installation Instructions (GEN II) Dodge Viper WARNING
WARNING Modification of your vehicle with the parts identified above may alter its stock performance; the buyer hereby expressly assumes all risks associated with any such modification. DISCLAIMER OF WARRANTY
More informationINSTALLATION INSTRUCTIONS Unitronic Intercooler Upgrade Kit for 2.0 TFSI (EA113) UH007-ICA
Unitronic recommends that you read through the entire installation instructions prior to beginning the installation to familiarize yourself with the included components, tools required, and procedures
More informationCOBB SF SHORT RAM INTAKE SYSTEM MazdaSpeed3
COBB SF SHORT RAM INTAKE SYSTEM MazdaSpeed3 Congratulations on your purchase of the COBB Tuning SF Intake System. The following instructions should assist you through your installation process. Please
More informationInstallation Instructions QUICKSILVER SHIFTER Fits: Chevrolet Camaro Pontiac Firebird Catalog # 80688
Installation Instructions QUICKSILVER SHIFTER Fits: 1973-1981 Chevrolet Camaro 1970-1981 Pontiac Firebird Catalog # 80688 WORK SAFELY! For maximum safety, perform this installation on a clean, level surface
More informationJK HD Skid Plate for Rear Falcon Shocks
1 JK HD Skid Plate for Rear Falcon Shocks Kit # 36-07-01-300 Important Notes: Prior to beginning this or any installation read these instructions to familiarize yourself with the required steps and evaluate
More informationINSTALLATION INSTRUCTIONS C-VS-2000-DUR-1 20 VEHICLE SPECIFIC CONSOLE for 2018 Dodge Durango with Standard Shifter
INSTALLATION INSTRUCTIONS C-VS-2000-DUR-1 20 VEHICLE SPECIFIC CONSOLE for 2018 Dodge Durango with Standard Shifter TOOLS REQUIRED: Phillips Screw Driver T-20 Torx bit Standard Socket set 9/64 Allen wrench
More informationIntegrated Engineering MK7/MQB Cold Air Intake Install Guide IEINCI2 & IEINCI8
Integrated Engineering MK7/MQB Cold Air Intake Install Guide IEINCI2 & IEINCI8 Thank you for purchasing another high quality Integrated Engineering product! This instruction guide is used for installation
More informationINSTALLATION INSTRUCTIONS
Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 21-8029 2011-2010 CHEVROLET Camaro V8-6.2L SEE * NOTE * NOTE: Legal in California only for racing vehicles which
More informationInstallation Instructions
Installation Instructions Application Fits 2015+ Subaru Legacy X7271 & X7272 2 & 1.25 EcoHitch Stealth LEGACY 2,000 lbs Weight Carrying/200 lbs Tongue Weight Torklift Central 315 Central Ave N Kent, WA
More informationINSTALLATION INSTRUCTIONS Unitronic DV Relocation Kit for 2.0 TSI Gen2 UH003-ICA
Unitronic recommends that you read through the entire installation instructions prior to beginning the installation to familiarize yourself with the included components, tools required, and procedures
More informationINSTALLATION INSTRUCTIONS GM Lower Control Arms P/N 52337, 52437, 52364, 52464, 52319, 52419, 52320, 52420, 52366, 52466, 52368, 52468
INSTALLATION INSTRUCTIONS GM Lower Control Arms P/N 52337, 52437, 52364, 52464, 52319, 52419, 52320, 52420, 52366, 52466, 52368, 52468 TOOLS AND SUPPLIES REQUIRED Floor Jack Jack Stands Wrench Set Hex
More informationSUBARU STI SUBARU WRX SHIFT BOOT INSTALL V1.0
2008-2018 SUBARU STI 2009-2018 SUBARU WRX SHIFT BOOT INSTALL V1.0 Congratulations on purchasing the finest automotive accessories on the market available for your vehicle. They will add a nice touch of
More informationPlease visit for the latest version of these installation instructions.
Please visit www.blueox.com for the latest version of these installation instructions. Attachment Tab Height: 19-1/2 Serial Number Attachment Tab Width: 19 Please read BOTH these and the General Information
More informationPush Start Ignition (05-10 All) Installation
Tools Required: Phillips head screwdriver Flat head screwdriver Ratchet 7mm Socket Torx T20 bit Wire strippers/cutters Hand file Needle nose pliers Installation Instructions: Push Start Ignition (05-10
More informationPlease visit for the latest version of these installation instructions.
Please visit www.blueox.com for the latest version of these installation instructions. Attachment Tab Height: 18 Serial Number Attachment Tab Width: 18 Please read BOTH these and the General Information
More informationPlease visit for the latest version of these installation instructions.
Please visit www.blueox.com for the latest version of these installation instructions. BX1726 (All Models) (No Active Shutters or E-Assist) Attachment Tab Height: 12 Serial Number Attachment Tab Width:
More informationDepress each tab as you pull the bezel off. The bezels are tight. L.H. shown.
2013-2014 Ford Mustang V6 & Boss 302 Lower Valance Fog Light Kit Parts List: Quantity: Tool List: Fog light & bulb with bracket 2 Flat head & Phillips screwdriver Black bezels 2 Ratchet & Socket set OR
More informationPARTS B&M Billet Knob B&M Billet Insert. O-Ring. Reverse Lockout Plate. Isolator. Nylon Slide Assy and Jam nut. Printed in the U.S.A.
Installation Instructions Precision Sport Shifter 2000 and up VW GOLF IV, JETTA IV (including GLI 6-spd), GTI, CABRIO, BEETLE, R32 (including 4-motion) 2000 and up Audi A3 1.8L and 1.9L Turbo Diesel, 1999-2002
More informationInstallation Instructions Z-Gate Shifter
Installation Instructions Z-Gate Shifter Part Number 80681 1998, 2001 by B&M Racing and Performance Products The B&M Z-Gate shifter can be used in vehicles equipped with most popular three speed automatic
More informationSport Sway Bar Kit (22425) Scion tc
Sport Sway Bar Kit (22425) Scion tc Thank you for your purchase from our new line of Scion tc parts. Please call us at (877) 4NO - ROLL if you have any questions regarding the service or installation of
More informationPlease visit for the latest version of these installation instructions.
Please visit www.blueox.com for the latest version of these installation instructions. Attachment Tab Height: 15-1/2 Serial Number Attachment Tab Width: 24 Please read BOTH these and the General Information
More informationFigure 1: Removal of shifter trim 2. Unscrew the 4 retaining screws holding the shifter boot down. See Figure 2.
PART #60055A Shifter, Short Throw, 2010-up Camaro, Manual PACKING LIST Before installation, use this checklist to make sure all necessary parts have been included. ITEM QTY CHECK PART NUMBER DESCRIPTION
More informationPlease visit for the latest version of these installation instructions.
Please visit www.blueox.com for the latest version of these installation instructions. Attachment Tab Height: 17-3/4 Attachment Tab Width: 18 Serial Number BX1708 2013-16 GMC Acadia (Includes Denali) 2017
More information2006, 2005 by B&M Racing and Performance Products
Installation Instructions Precision Sport Shifter 1997 and up C5 & C6 Chevrolet Corvette (see www.bmracing.com for the latest vehicle fitment applications and model years) Part Number 45044 2006, 2005
More informationM-7210-Z3 Focus Short-Throw Shifter (fits 2000-April 2002) INSTALLATION INSTRUCTIONS
Please visit www.fordracingparts.com for the most current instruction information!!! PLEASE READ ALL OF THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION. AT ANY TIME YOU DO NOT UNDERSTAND THE
More informationLegacy 3.6R CVT Cooler Installation
2015-2017 Legacy 3.6R CVT Cooler Installation WARNING!! - Modification and working on your car involves some dangers and risks and may cause injury to you or damage to your vehicle if not done properly
More informationMustang Short Throw Sport Shifter (All 83 - Early 01 & V6 T-5/T-45 Transmission) - Installation Instructions
Mustang Short Throw Sport Shifter (All 83 - Early 01 & 01-04 V6 T-5/T-45 Transmission) - Installation Instructions The below installation instructions work for the following products: Mustang Short Throw
More informationKit Part Number:
Equipped with AEM DRYFLOW Filter No oil required! Kit Part Number: 21-8203 2003-2005 Dodge Ram 5.7L V8 CARB EO # D-392-28 2005 Dodge Powerwagon Hemi CARB EO # D-392-28 Brute Force Intake Systems that are
More information