Installation Manual Short Shift Kit 2000 and up Toyota Celica 2000 and up MR Spyder
|
|
- Chester Horton
- 5 years ago
- Views:
Transcription
1 Page 1 Installation Manual Short Shift Kit 2000 and up Toyota Celica 2000 and up MR Spyder 1. Unscrew the shift knob and remove the boot. 2. Remove cover which houses the lighter assembly. There are four clips holding it to the center console, they just pop out.
2 Page 2 3. Unplug the lighter assembly. Below you can see the cover off and the four clips which hold it to the center console. 4. Remove the two screws holding the power window controls (if applicable). Next unplug the locks to remove the assembly.
3 Page 3 5. Remove the rubber mat, and the two bolts in the storage compartment of the center console. 6. Remove the two screws on either side of the center console.
4 Page 4 7. Unscrew the 2 screws at the front of the center console. After the bolts and the screws have been removed the entire console will be free and can be taken out 8. Carefully slide an exacto knife under the clip on the right side of the assembly to remove it. CAUTION : Be extremely careful in this step, if the knife is torqued too hard the blade could break and become a dangerous projectile. 9. Insert a flat head screw driver into the gap created by the exacto knife to pry the clip off.
5 Page Use a punch to drive out the pin on the opposite side of the shifter. Tap lightly with a hammer until the pin is driven out of the assembly. 11. Remove the clip on the left side of the assembly. 12. Remove the four bolts securing the assembly to the chassis.
6 Page Remove the retainers holding the shift rods to the assembly by pulling up on them with a set of pliers. 14. Lift up the assembly and remove the bottom clip holding the shifter to the linkage.
7 Page Pull out the pin and the L shaped arm which was held on by the clip and remove the shifter. Step 16: Use the cup remover tool included with the kit to remove both plastic cups on the original shifter. To do so, place the cup remover tool on top of the open jaws of a vice, the jaws should be approximately 1 apart. Hang the shifter from the tool as shown, be sure the shifter is inserted completely into the slot in the tool. Insert a punch into the center hole through the plastic cup and tap firmly with a hammer to separate the original shifter from cup. Repeat for 2nd cup.
8 Re-Installation Page 8 Install the plastic cups which you removed from the original shifter onto the TWM shifter. Grease the cups and pivot balls. Place the cup on a firm surface and push the TWM shifter into it until it pops in. Remove the rubber bushings in the plastic assembly. Install the 4 aluminum spacers included with the kit beneath the plastic assembly bevel edge up. Now replace the plastic assembly on top of the aluminum spacers. Secure with the 4 long bolts and washers included with the kit.
9 Page 9 Lightly grease the large pivot ball before installing the TWM shifter into the plastic assembly in place of the stock shifter. Re-install the clip on the bottom of the shifter.
10 Page 10 Replace the top plastic retaining ring and rubber grommet. Replace the top part of the assembly, drive the rear pin back in, and re-insert the L shaped shift arm.
11 Page 11 Install the clip included in the kit onto the shaft at the front of the assembly. Drive the clip on with a 12mm socket to secure it properly against the plastic assembly. Be sure the shaft is pushed all the way into the assembly and the clip is on all the way so there is no free play.
12 Page 12 Re-install the clip on the driver s side of the L shaped shift arm. Re-install the console, boot, and shift knob and you re ready to drive.
13 Page 13 Legal Disclaimer TWM Performance is not responsible for the misuse, incorrect installation, or failure of any product we sell. Under no circumstances, including but not limited to negligence, will TWM Performance be liable for special or consequential damages that result from the use or inability to use our products. TWM Performance does not assume responsibility for any damage to the user, passenger or vehicle resulting from the operation of a TWM Performance product. TO PROTECT USERS FROM INJURY OR DEATH. THE USER ASSUMES ALL RISKS. Autocrossing, track events, and high speed driving are all dangerous activities - always drive responsibly and safely. Warranty Installation of some TWM Performance products may or may not void factory warranties. Always keep OEM equipment that has been replaced in case work is required at the dealer or the vehicle is sold. This warranty covers the original purchasing consumer. This warranty is limited to repair or replacement by TWM Performance of any TWM Performance product that fails because of a defect in materials or workmanship. Warranty does not cover the following: -Damage incurred to related vehicle components -Regular day to day wear on vehicle -Shipping costs for replacements -Mounting hardware and bearings -Installation costs and vehicle down time -Products that have been modified, incorrectly installed or misused.
Installation of the Toyota Celica TWM Performance Short Throw Shift Kit Plastic Shifter Assembly
Installation of the 1992-1993 Toyota Celica TWM Performance Short Throw Shift Kit Plastic Shifter Assembly Page 1 1. Remove the stock shift knob and boot cover 2. Carefully slide an exacto knife under
More informationToyota Celica Short Throw Shift Kit Installation Manual (Metal Assembly)
1992-1993 Toyota Celica Short Throw Shift Kit Installation Manual (Metal Assembly) Page 1 1. Remove shift knob and plastic cover from shift assembly. 2. Remove the three nuts holding the top part of the
More informationInstructions to Install TWM Performance Toyota Celica Turbo 4WD Short Throw Shift Kit
Instructions to Install TWM Performance 1990-1991 Toyota Celica Turbo 4WD Short Throw Shift Kit Page 1 Step 1: Unscrew shift knob and remove console piece with boot. Step 2: Unbolt the seven bolts circled
More informationInstructions to Install TWM Performance Toyota Celica Short Throw Shift Kit
Instructions to Install TWM Performance 1990-1991 Toyota Celica Short Throw Shift Kit Page 1 Step 1: Unscrew shift knob and remove console piece with boot. Step 2: Unbolt the seven bolts circled here (one
More information95-97 Toyota Tercel & Paseo Short Throw Shifter Installation Manual
95-97 Toyota Tercel & 92-97 Paseo Short Throw Shifter Installation Manual Estimated Installation Time: 40-60 Minutes Tools Required: -Philips head screwdriver and flat head screwdriver -Bench vise -10mm,
More informationInstallation Manual TWM Performance Short Shift Kit 2006 and up Toyota Yaris
Installation Manual TWM Performance Short Shift Kit 2006 and up Toyota Yaris 1. Unscrew the shift knob by rotating counter clockwise. 2. Remove the carpet or mat at the bottom of the cup holder at the
More informationInstallation Manual TWM Performance Short throw shifter 2001 and up Hyundai Accent
Installation Manual TWM Performance Short throw shifter 2001 and up Hyundai Accent 1. Place the vehicle on a flat surface with blocks in front and behind the wheels preventing unwanted movement. The car
More information2. Disconnect both plastic connectors beneath the rear part of the center console. Note their locations for re-installation.
Installation Manual TWM Performance Short Shifter 2002 and up Subaru Impreza WRX/RS/TS 1996-2001 Subaru Impreza 2004 and Up Saab 9-2X 1996-2001 Subaru Legacy 1997-2004 Subaru Forester 1. Open the center
More informationInstallation Manual TWM Performance Short Shifter 2008 Mitsubishi Lancer
Page 1 Installation Manual TWM Performance Short Shifter 2008 Mitsubishi Lancer Please Note: It is preferable to park on a flat surface, as you will have to engage and disengage the hand brake and shift
More informationInstallation Manual TWM Performance Short Shift Kit 2003 And Up Saturn Ion
Installation Manual TWM Performance Short Shift Kit 2003 And Up Saturn Ion It s preferable to park on a flat surface, as you may have to engage and disengage the hand brake and shift from gears to neutral.
More informationInstallation Manual TWM Performance Honda Accord 2008+
Installation Manual TWM Performance Honda Accord 2008+ Begin the installation by parking on a flat surface, as you will have to engage and disengage the hand brake and shift from gears to neutral. If you
More informationInstallation Manual TWM Performance Short Shifter Subaru Forester up to 2005
- 1 - Installation Manual TWM Performance Short Shifter Subaru Forester up to 2005 Please Note: It is preferable to park on a flat surface, as you will have to engage and disengage the hand brake and shift
More informationInstallation Manual TWM Performance Short Shift Kit Stage 1 and Stage 2 MazdaSpeed 6
Page 1 Installation Manual TWM Performance Short Shift Kit Stage 1 and Stage 2 MazdaSpeed 6 Please Note: It is preferable to park on a flat surface, as you will have to engage and disengage the hand brake
More informationInstallation Manual TWM Performance Full replacement short shifter assembly Civic all trims and models
Installation Manual TWM Performance Full replacement short shifter assembly 2006+ Civic all trims and models Begin the installation by parking on a flat surface, as you will have to engage and disengage
More informationInstallation Manual TWM Performance Kia Forte Short Shifter
Installation Manual TWM Performance Kia Forte 2009+ Short Shifter Begin the installation by parking on a flat surface, as you will have to engage and disengage the hand brake and shift from gears to neutral.
More informationInstallation Manual TWM Performance 2010 Mazda 3 short shifter 5 and 6 speed non-mazdaspeed
Installation Manual TWM Performance 2010 Mazda 3 short shifter 5 and 6 speed non-mazdaspeed Begin the installation by parking on a flat surface, as you will have to engage and disengage the hand brake
More informationInstallation Manual TWM Performance Short Shifter Subaru STi 2008+
- 1 - Installation Manual TWM Performance Short Shifter Subaru STi 2008+ Please Note: It is preferable to park on a flat surface, as you will have to engage and disengage the hand brake and shift from
More informationInstallation Manual TWM Performance Toyota GT86 / Scion FRS / Subaru BRZ Direct Replacement Short Shifter
Installation Manual TWM Performance Toyota GT86 / Scion FRS / Subaru BRZ Direct Replacement Short Shifter Begin the installation by parking on a flat surface, place wooden blocks in front or behind the
More informationInstallation Manual TWM Performance Short Shift Kit Estimated Installation Time: Tools required:
Page 1 Installation Manual TWM Performance Short Shift Kit 1993-2001 Nissan Altima 1991-2001 Infiniti G20 1991-2001 Nissan Sentra- 200SX 1991-1993 Nissan NX 1986-1989 Nissan Stanza 1995-2001 Nissan Maxima
More informationInstallation Manual TWM Performance Chevrolet Camaro 5 th Gen Short Shifter
Installation Manual TWM Performance Chevrolet Camaro 5 th Gen Short Shifter Begin the installation by parking on a flat surface, place wooden blocks in front or behind the wheels to prevent the car from
More informationInstallation Manual TWM Performance Chevrolet Camaro 5 th Gen Full Replacement Short Shifter
Installation Manual TWM Performance Chevrolet Camaro 5 th Gen Full Replacement Short Shifter Begin the installation by parking on a flat surface, place wooden blocks in front or behind the wheels to prevent
More informationInstallation Manual TWM Performance Short Shifter Nissan 350Z, 370Z Infiniti G35, G37
Installation Manual TWM Performance Short Shifter Nissan 350Z, 370Z Infiniti G35, G37 It is preferable to park on a flat surface, as you will have to engage and disengage the hand brake and shift from
More informationInstallation Manual TWM Performance Short Shifter Cobalt SS/SC, SS/TC, HHR SS, Ion Redline and Saab 9-3
Page 1 Installation Manual TWM Performance Short Shifter Cobalt SS/SC, SS/TC, HHR SS, Ion Redline and Saab 9-3 Please Note: It is preferable to park on a flat surface, as you will have to engage and disengage
More informationInstallation Manual TWM Performance Shift Boot 2006 and up Honda Civic Si
Page 1 Installation Manual TWM Performance Shift Boot 2006 and up Honda Civic Si Begin the installation by parking on a flat surface, as you may have to engage and disengage the hand brake and shift from
More informationjames Barone Racing Aftermarket Parts and Accessories
Page1 james Barone Racing Aftermarket Parts and Accessories 2010 2013 MAZDASPEED 3 Short Throw Shifter Installation Instructions What you will need: Ratchet wrench 6 socket extension 10mm and 13mm socket
More informationChevrolet Cobalt Short Shifter Installation Manual
Chevrolet Cobalt Short Shifter Installation Manual Pull shift boot down on the shifter shaft. Pull up on the shift knob to remove it. It requires some force. Remove the ebrake console, shifter console
More informationJBR Adjustable Short Shift Plate Kit Pre-Installation Instructions. Attaching the stand-off to the Shift Plate
JBR Adjustable Short Shift Plate Kit Pre-Installation Instructions Attaching the stand-off to the Shift Plate 1. With the Shift Plate facing up, insert the male end of the stand-off through the slotted
More informationSteeda S550 MT-82 Tri-Ax Race Short Throw Shifter Installation Instructions For Parts: ,
Steeda S550 MT-82 Tri-Ax Race Short Throw Shifter Installation Instructions For Parts: 555-7317, 555-7318 Tools required 1. 7mm socket 2. 10mm socket 3. 13mm socket 4. 15mm socket 5. 18mm socket 6. 3/8
More informationSteeda S550 Mustang Street Short Throw Shift Lever Installation Instructions For Part:
Steeda S550 Mustang Street Short Throw Shift Lever Installation Instructions For Part: 555-7316 Tools required 1. 7mm socket 2. 10mm socket 3. Small flathead screwdriver 4. T20 torx bit or driver 5. Vise
More informationJames Barone Racing Aftermarket Parts and Accessories
Page1 James Barone Racing Aftermarket Parts and Accessories What you will need: 2014+ Mazda 3, 6 and CX-5 Adjustable Rear Camber Arm Installation Instructions. Jack, jack stands Socket wrench Socket wrench
More informationInstallation Instructions INDY SHIFTER Fits: Mustang Fastback & Convertible with MT-82 Transmission Catalog #
Installation Instructions INDY SHIFTER Fits: 2015-2018 Mustang Fastback & Convertible with MT-82 Transmission Catalog # 3916036 Watch our installation video on YouTube WORK SAFELY! For maximum safety,
More informationWRANGLER TJ INSTALLATION INSTRUCTIONS Kit #: TJ251K/KN/KST/KSTN TJ401K/KN/KST/KSTN
WRANGLER TJ INSTALLATION INSTRUCTIONS Kit #: TJ251K/KN/KST/KSTN TJ401K/KN/KST/KSTN Before beginning the installation, read these instructions and the enclosed driver s WARNING NOTICE thoroughly and completely.
More informationBD POWER SHORT SHIFTER Dodge Speed Dodge Speed Dodge Speed.
June 05 Cummins Short Shift Kit (1031050/1031055/103156) 1 BD POWER SHORT SHIFTER for Dodge Cummins 1998-2005 Manual Transmissions Application Chart 1031056 Dodge 1998-2002 5 Speed 1031050 Dodge 2000-2002
More informationSteeda S550 Mustang Street Short Throw Shift Lever Installation Instructions: &
Steeda S550 Mustang Street Short Throw Shift Lever Installation Instructions: 555-7316 & 555-7322 Tools required 1. 7mm socket 2. 10mm socket 3. Small flathead screwdriver 4. T20 torx bit or driver 5.
More information97-06 Jeep Wrangler TJ Installation Instructions Kit #: TJ251K-SVX / TJ253K-SVX TJ401K-SVX / TJ403K-SVX
www.skyjacker.com 97-06 Jeep Wrangler TJ Installation Instructions Kit #: TJ251K-SVX / TJ253K-SVX TJ401K-SVX / TJ403K-SVX Before beginning the installation, read these instructions and the enclosed driver
More information97-06 Jeep TJ Wrangler Installation Instructions Models Kit# TJ251K/TJ401K-SX -DX 03 Models Kit# TJ253K/TJ403K-SX -DX
97-06 Jeep TJ Wrangler Installation Instructions 97-02 Models Kit# TJ251K/TJ401K-SX -DX 03 Models Kit# TJ253K/TJ403K-SX -DX Before beginning the installation, read these instructions and the enclosed driver
More informationSubaru 5-Speed Double Adjustable Short Throw Shifter
Subaru 5-Speed Double Adjustable Short Throw Shifter 1999+ Subaru Impreza 5-Speed 2004-2005 Subaru Forester XT 5-Speed Congratulations on your purchase of the COBB Tuning Double Adjustable Short Throw
More informationInstallation Instructions COMPETITION/PLUS SHIFTER Ford Mustang MT82 6-Speed Manual Transmission Catalog#
Installation Instructions COMPETITION/PLUS SHIFTER 2015-2017 Ford Mustang MT82 6-Speed Manual Transmission Catalog# 3916037 Rev. 00 WORK SAFELY! For maximum safety, perform this installation on a clean,
More informationWRANGLER TJ INSTALLATION INSTRUCTIONS
WRANGLER TJ INSTALLATION INSTRUCTIONS 1997-02 Models Kit# TJ251K/TJ401K 2003-06 Models Kit# TJ253K/TJ403K Before beginning the installation, read these instructions and the enclosed driver s WARNING NOTICE
More informationPARTS TOOLS. Set Screw. Washer (2) Blue Bushing (2) Black Bushing (2) B&M Short Throw Shifter. Jam Nut Grease. Retaining Ring (2) Insert (2)
Installation Instructions SHORT THROW SHIFTER Fits: Porsche Boxter, Boxter S, 911, 996 Cayman & Cayman S models See Application Guide for specific year ranges and engine sizes Catalog # 45135 WORK SAFELY!
More information2014+ Mazda 3/6 & CX-5 Front Sway Bar Installation Instructions
Page1 James Barone Racing 2014+ Mazda 3/6 & CX-5 Front Sway Bar Installation Instructions Tools Required: Jack & jack stands or a lift Socket wrench 3 and 12 socket extensions 10mm, 14mm, 17mm, 19mm socket
More informationTK08 TUNING KIT TECHNICAL MANUAL FOR 16/26/27/28 SERIES SHOCKS Revised 6/17/14
Tech Line: (952) 985-5675 Fax (952) 985-5679 21730 Hanover Ave. Lakeville, MN 55044 www.qa1.net www.facebook.com/qa1motorsports TK08 TUNING KIT TECHNICAL MANUAL CONTENTS UNDER PRESSURE! USE EXTREME CAUTION
More informationHURST COMP/PLUS SHIFTER 2015 Ford Mustang (Getrag MT82 six-speed manual transmission) Catalog # by Hurst Performance
FORM 159 0205 07/15 HURST COMP/PLUS SHIFTER 2015 Ford Mustang (Getrag MT82 six-speed manual transmission) Catalog #391 0205 2015 by Hurst Performance Thank you for purchasing the Hurst Comp/Plus Shifter.
More information2. Remove front wheels.
1 PARTS DIAGRAM 2 Installation Instructions: (PASSENGER SIDE) 1. Place jack under center of RUV front end and lift until front wheels clear the ground. Be careful to support the RUV properly so that it
More information97-06 Jeep TJ Wrangler 2. 5 " & 4 " S u s p e n s i o n L i f t Installation Instructions
97-06 Jeep TJ Wrangler 2. 5 " & 4 " S u s p e n s i o n L i f t Installation Instructions Safety Glasses Metric / Standard Wrenches & Sockets Drill / Assorted Drill Bits Floor Jack Jack Stands Measuring
More informationTrail-Creeper Dual Transfer Case Adapter
Trail-Creeper Dual Transfer Case Adapter Installation Instructions For Kits: 100001-1-KIT 21 Spline 100006-1-KIT 23 Spline KIT Contents: 23 or 21 Spline Coupler 1.0 Adapter Plate w/ Bearings Installed
More informationADVANCE ADAPTERS INC. P/N: JEEP TJ & (XJ 84-01) ATLAS 4 SPEED CABLE SHIFTER units built after 5/1/12
Paso Robles, CA 93447 PAGE 1 OF 9 Telephone: (800) 350-2223 Fax: (805) 238-4201 Page Rev. Date: 05-12-15 KIT CONSISTS OF: No. Qty Part No. Description 1 1 302051 BASE- TWIN STICK MOUNT 2 1 302080 STUD
More information4. Remove the cotter pin that secures the castle nut to the axle. Once you have done this remove the castle nut and pull off the hub/rotor assembly.
780 Professional Drive N. Shreveport, LA 71105 Phone (318)-524-2270 Fax (318)-524-2297 Max Clearance Honda Pioneer 1000 Front Forward Arched Control Arm Kit Read before Installation This product is designed
More informationM-7210-Z3 Focus Short-Throw Shifter (fits 2000-April 2002) INSTALLATION INSTRUCTIONS
Please visit www.fordracingparts.com for the most current instruction information!!! PLEASE READ ALL OF THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION. AT ANY TIME YOU DO NOT UNDERSTAND THE
More informationIPSCO STS (Short Throw Shifter) Installation Instructions Dodge Viper WARNING
WARNING Modification of your vehicle with the parts identified above may alter its stock performance; the buyer hereby expressly assumes all risks associated with any such modification. DISCLAIMER OF WARRANTY
More informationStop! Read This Important Information.
Stop! Read This Important Information. Stop, Do Not Proceed, Read This This door replacement kit is designed for the replacement of doors on a Supertop ONLY! This door will not work on any other style
More informationJEEP TJ & (XJ 84-01) ATLAS 2 SP.
KIT CONSISTS OF: No. Qty Part No. Description 4320 Aerotech Center Way, Page 1 of 9 1 1 302051-RLE BASE- TWIN STICK MOUNT 42RLE 2 1 302080 STUD BOLT 1/2"-13 X 7 (XJ) 3 1 303120 SERRATED LOCK NUT 1/2" X
More informationTK08 TUNING KIT TECHNICAL MANUAL FOR 16/26/27/28 SERIES SHOCKS Revised 6/25/14 Tech Line: (952) Fax (952)
Tech Line: (952) 985-5675 Fax (952) 985-5679 21730 Hanover Ave. Lakeville, MN 55044 www.qa1.net www.facebook.com/qa1motorsports TK08 TUNING KIT TECHNICAL MANUAL CONTENTS UNDER PRESSURE! USE EXTREME CAUTION
More informationIPSCO STS (Short Throw Shifter) Installation Instructions (GEN II) Dodge Viper WARNING
WARNING Modification of your vehicle with the parts identified above may alter its stock performance; the buyer hereby expressly assumes all risks associated with any such modification. DISCLAIMER OF WARRANTY
More informationHAND THROTTLE CONTROL KIT
1 HAND THROTTLE CONTROL KIT www.teraflex.com #87000 #87002 Important Notes: Prior to beginning this or any installation read these instructions to familiarize yourself with the required steps and evaluate
More informationJackhammer Trolley JHT
Jackhammer Trolley JHT OPERATOR S MANUAL CONTENTS ABOUT THIS MANUAL 2 - Key Terms 2 - Disclaimer 3 PRODUCT INFORMATION 4 - Safety Information 4 o General Safety Instructions 4 o Safety Stickers 5-6 - Warranty
More informationREPAIR PARTS MANUAL MODEL NUMBER SB240 (MFG. ID. NO ) Snow Thrower Rev BY Printed in U.S.A.
MANUAL MODEL NUMBER SB0 (MFG. ID. NO. 919100000) Snow Thrower 19 9- Rev. 0..0 BY Printed in U.S.A. AUGER HOUSING / IMPELLER ASSEMBLY 1 1 1 7 1 10 1 9 7 8 7 8 11 1 0 9 0 9 10 18 8 19 8 19 19 0 10 8 19 1
More informationSachs shock manual. ( ) 2 & 4 Stroke RR Enduro. ( ) RS Dual Sport
Sachs shock manual (2013 2015) 2 & 4 Stroke RR Enduro (2014-2015) RS Dual Sport 1 Introduction The procedures in this manual must take place in a clean environment using professional tools and some specific,
More informationINSTALLATION GUIDE Bolt-On Drag-Race Strut Clip Chevy II
INSTALLATION GUIDE 7702 Bolt-On Drag-Race Strut Clip 1962-67 Chevy II Description: STRUT CLIP 4130 BOLT ON 62-67 CHEVY II, INCLUDES 4130 ROUND TUBE FRAME CLIP, DOUBLE-ADJUSTABLE STRUTS, ADJUSTABLE-HEIGHT
More informationJames Barone Racing Custom Fabrication of Aftermarket Parts and Accessories Mazda 3 and MAZDASPEED 3 Mud Flap Installation Instructions
James Barone Racing Custom Fabrication of Aftermarket Parts and Accessories 2010+ Mazda 3 and MAZDASPEED 3 Mud Flap Installation Instructions To protect and avoid damage to your new JBR Mud Flaps care
More informationInstallation Instructions Z-Gate Shifter
Installation Instructions Z-Gate Shifter Part Number 80681 1998, 2001 by B&M Racing and Performance Products The B&M Z-Gate shifter can be used in vehicles equipped with most popular three speed automatic
More informationREPAIR PARTS MANUAL MODEL NUMBER PM105 (MFG. ID. NO ) Snow Thrower BY Printed in U.S.A.
MANUAL MODEL NUMBER PM10 (MFG. ID. NO. 9191001103) Snow Thrower 3 0 1-8 08.11.0 BY Printed in U.S.A. AUGER HOUSING / IMPELLER ASSEMBLY SNOW THROWER - MODEL NO. PM10 (9191001103), PRODUCT NO. 91 91 00-11
More information16K Revolution Service Kit Instructions 86016
86016 Equipment Required: Wrenches: 15/16, 1 1/8, Torque Wrench, Rubber Mallet Included Service Kit Items: 1 Qty. (1) Wear Plate 2 Qty. (1) Pivot Bushing 3 Qty. (1) Bearing Cup 4 Qty. (1) Bearing 1 5 Qty.
More informationBRAKE SYSTEM Toyota Celica DESCRIPTION DRUM BRAKES ADJUSTMENTS BRAKE PEDAL HEIGHT ADJUSTMENTS BRAKE PEDAL FREE PLAY ADJUSTMENTS
BRAKE SYSTEM 1988 Toyota Celica 1988-89 BRAKES Toyota Celica, Corolla, MR2, Tercel DESCRIPTION The hydraulic brake system uses a tandem master cylinder with a vacuum power assist servo. MR2 and some Celica
More informationUNIVERSAL FLOOR SHIFT CONVERSION KIT
UNIVERSAL FLOOR SHIFT CONVERSION #7668 These instructions apply to the following MR. GASKET products: 7668 - Universal Floor Shift Conversion Kit, Fits Most Rear-Wheel Drive Car Applications With Automatic
More information2017-Present Can-Am Maverick X3 XRS Front Upper A-Arm Kit *Installation Instructions*
2017-Present Can-Am Maverick X3 XRS Front Upper A-Arm Kit *Installation Instructions* PART# 370-90350 Introduction - Installation requires a qualified mechanic. - Read instructions carefully and study
More informationINSTALLATION INSTRUCTIONS GM Lower Control Arms P/N 52337, 52437, 52364, 52464, 52319, 52419, 52320, 52420, 52366, 52466, 52368, 52468
INSTALLATION INSTRUCTIONS GM Lower Control Arms P/N 52337, 52437, 52364, 52464, 52319, 52419, 52320, 52420, 52366, 52466, 52368, 52468 TOOLS AND SUPPLIES REQUIRED Floor Jack Jack Stands Wrench Set Hex
More informationInstallation Instructions for the EVO3 Height-Adjustable Ultimate Short Shifter
Installation Instructions for the EVO3 Height-Adjustable Ultimate Short Shifter for 1992-2005 325, 323, 318 and 1986-1994 525, 528, 535, 540 5-speed models only. (part number USSE3 and USSE5) Thank you
More informationREPAIR PARTS MANUAL MODEL NUMBER PM85 (MFG. ID. NO ) Snow Thrower Rev SR Printed in U.S.A.
MANUAL MODEL NUMBER PM8 (MFG. ID. NO. 990000) Snow Thrower 3 0 8-3 Rev. 0.08.09 SR Printed in U.S.A. AUGER HOUSING / IMPELLER ASSEMBLY SNOW THROWER - MODEL NO. PM8 (990000), PRODUCT NO. 9 9 00-0 3 0 9
More informationURD Short Shifter Installation Tacoma 5 speed Runner 5 speed
URD Short Shifter Installation 1995-2004 Tacoma 5 speed 1996-2002 4Runner 5 speed Introduction: URD introduced our first short throw shifter for the 05+ Tacoma 6 speed transmission. This unit became very
More informationHalf Door Installation Instructions
Half Door Installation Instructions For: CJ5 (1976-1983) Part Number: 53027 Congratulations on your purchasing decision. Bestop designed these Doors to give you years of dependability and performance with
More informationINSTALLATION INSTRUCTIONS: LONG TRAVEL KIT 07+ FJ CRUISER and 05+ TACOMA
INSTALLATION INSTRUCTIONS: LONG TRAVEL KIT 07+ FJ CRUISER and 05+ TACOMA ISNTALLATION DIFFICULTY: Advanced APPROX TIME: 6-8 Hours REQUIRED TOOLS: 14mm-35mm sockets, wrenches, and ratchet 9/16 and 5/8 12
More informationSuzuki Samurai 6.5 Transfer Case Gear Kit, KIT
Suzuki Samurai 6.5 Transfer Case Gear Kit, 105004-3-KIT Kit Contents: Gear, 26 Spline/26 Tooth 1.0 Gear, 44 Tooth 1.0 Gear, 58 Tooth/23 Tooth 1.0 Gear, 67 Tooth/ 27 Tooth 1.0 Counter Shaft 1.0 Counter
More informationPush Start Ignition (05-10 All) Installation
Tools Required: Phillips head screwdriver Flat head screwdriver Ratchet 7mm Socket Torx T20 bit Wire strippers/cutters Hand file Needle nose pliers Installation Instructions: Push Start Ignition (05-10
More information16K and 19K Sidewinder TM Service Kit Instructions 86005
86005 Equipment Required: Wrenches: 15/16, 1 1/8, Torque Wrench, Rubber Mallet Included Service Kit Items: 1 Qty. (1) Wear Plate 2 Qty. (6) 5/8 Conical Washer 3 Qty. (2) Wedge Bolt, 5/8-11 X 1 3/4 GRD
More information5 th Airborne Sidewinder Service Kit Instructions 94316
94316 Equipment Required: Wrenches: 15/16, Torque Wrench, Rubber Mallet 3 4 5 2 Included Service Kit Items: 1 Qty. (1) Wear Plate 2 Qty. (1) Wear Bushing 3 Qty. (1) Wear Disc 4 Qty. (4) 5/8-11x2 GRD8 Bolt
More informationNOTICE- THIS K-MEMBER REQUIRES THE USE OF COIL OVER SUSPENSION. K-MEMBER WILL NOT WORK WITH FACTORY STYLE SPRINGS.
Technical Support Line: (952) 985-5675 Email: Info@QA1.net 21730 Hanover Ave. Lakeville, MN 55044 www.qa1.net INSTALLATION INSTRUCTIONS MUSTANG K-MEMBER P/N MUK11, MUK12, MUK13 NOTICE- THIS K-MEMBER REQUIRES
More informationJBR Mazda 3 & Mazdaspeed 3 Adjustable Rear Camber Arm Installation Instructions
james Barone Racing Aftermarket Parts and Accessories JBR 2004 2013 Mazda 3 & Mazdaspeed 3 Adjustable Rear Camber Arm Installation Instructions Tooling: Jack and jack stands Ratchet wrench 17mm socket
More informationJames Barone Racing Aftermarket Parts and Accessories Ford Focus ST Front Sway Bar Installation Instructions. Page1
Page1 James Barone Racing Aftermarket Parts and Accessories 2013+ Ford Focus ST Front Sway Bar Installation Instructions Tools Required: Jack Lift or ramps Ratchet wrench Torque Wrench 6 and 12 Extension
More informationInstallation Instructions LamboStyleDoors (The instruction are to be used as a reference. Please repeat for both doors)
Installation Instructions LamboStyleDoors (The instruction are to be used as a reference. Please repeat for both doors) Pre installation check list: - Double check vehicles data with TUV certificate -
More information2006, 2005 by B&M Racing and Performance Products
Installation Instructions Precision Sport Shifter 1997 and up C5 & C6 Chevrolet Corvette (see www.bmracing.com for the latest vehicle fitment applications and model years) Part Number 45044 2006, 2005
More informationINSTALLATION GUIDE. KTM 125, 144, Stroke KTM 250, Stroke KTM 250 SXF, XC, XC-W KTM 450, 505 SXF Manual Revision:
REKLUSE MOTOR SPORTS The z-start Pro Clutch INSTALLATION GUIDE KTM 125, 144, 200 2-Stroke KTM 250, 300 2-Stroke KTM 250 SXF, XC, XC-W KTM 450, 505 SXF 191-836 Manual Revision: 050307 2002 Rekluse Motor
More informationInstallation Instructions LamboStyleDoors (The instruction are to be used as a reference. Please repeat for both doors)
Installation Instructions LamboStyleDoors (The instruction are to be used as a reference. Please repeat for both doors) Mercedes C-Class Sport coupé type W203 Part number 500 25 009 Pre installation check
More informationA Division of Thiessen Products, Inc.
The JIMS FORCEFLOW CYLINDER HEAD COOLER is designed for Twin Cam Models 1999 to present. Also fits all JIMS Twin Cam Race Engines. NOTE: These instructions show the installation of this product on a 2012
More informationStar Mini Phantom. Interior Undercover Mini LED Light. PATENTS D530,029 and D632,421. ULB9E Series
Star Mini Phantom Interior Undercover Mini LED Light PATENTS D530,029 and D632,421 ULB9E Series IMPORTANT: Please read all of the following instructions before installing your new light. CAUTION: Please
More informationJBR MAZDASPEED
Page1 james Barone Racing Aftermarket Parts and Accessories JBR 2007 2009 MAZDASPEED 3 Front Mount Intercooler Piping Kit Installation Instructions for TR8 Intercooler Tooling: o Jack, Jack Stands, Ramps
More informationFactory Five Racing, Inc. 818 Kit Assembly manual revision 1J update
Factory Five Racing, Inc. 818 Kit Assembly manual revision 1J update Turbo coolant overflow tank...1 Shifter handle...4 Install...4 Door skin...7 Door Liner... 10 Side mirrors... 14 Door handles and pulls...
More informationTechnical Support Line: (952) Fax Line: (952) Hanover Ave. Lakeville, MN
Technical Support Line: (952) 985-5675 Fax Line: (952) 985-5679 21730 Hanover Ave. Lakeville, MN 55044 www.qa1.net INSTALLATION INSTRUCTIONS QA1 P/N CC104MU Camber Caster Plates 1994-2004 Mustang 5.0/4.6
More informationInstallation Instructions Short Throw Shifter
Installation Instructions Short Throw Shifter 2000-2001 Audi TT 1.8L Turbo Including FWD and AWD (Quattro) Part Number 45146 2003,2001 by B&M Racing and Performance Products LLC This B&M Short Throw Shifter
More informationMC624ES. Part's Manual
MCES Part's Manual Gasoline containing up to 0% ethanol (E0) is acceptable for use in this machine. The use of any gasoline exceeding 0% ethanol (E0) will void the product warranty. 8 8-7 REPAIR S SNOW
More informationInstallation Instructions for the EVO3 Height-Adjustable Ultimate Short Shifter. for F80 M3 and F82 M4
Installation Instructions for the EVO3 Height-Adjustable Ultimate Short Shifter for 2013+ F80 M3 and F82 M4 part number USSF80 Thank you for purchasing the Ultimate Shift Kit. Please read these directions
More informationDetroit Speed, Inc. Rear Coilover Tower Brace Kit Camaro P/N:
Detroit Speed, Inc. Rear Coilover Tower Brace Kit 2016+ Camaro P/N: 042433 The Detroit Speed, Inc. 2016+ Camaro Rear Coilover Tower Brace Kit is a bolt-in design that increases overall vehicle stiffness.
More informationDetroit Speed, Inc. Selecta-Speed Wiper Kit Corvette P/N:
Detroit Speed, Inc. Selecta-Speed Wiper Kit 1968-72 Corvette P/N: 121621 A downpour of rain will no longer hinder your ability to clearly see the road. The Detroit Speed Selecta-Speed Wiper Kit provides
More informationREPAIR PARTS MANUAL MODEL NUMBER SB300 (MFG. ID. NO ) Snow Thrower Rev BY Printed in U.S.A.
MANUAL MODEL NUMBER SB00 (MFG. ID. NO. 990000) Snow Thrower 9 9-9 Rev. 0..0 BY Printed in U.S.A. AUGER HOUSING / IMPELLER ASSEMBLY 9 0 9 0 9 9 9 9 0 9 9 9 0 0 KEY PART NO. NO. DESCRIPTION AUGER HOUSING
More informationDetroit Speed, Inc. Electric Headlight Door Kit Corvette P/N: &
Detroit Speed, Inc. Electric Headlight Door Kit 1968-82 Corvette P/N: 122006 & 122007 The Detroit Speed Inc. Electric Headlight Door Kit replaces the stock vacuum actuated system on all 1968-82 Corvettes.
More informationULTRA WEIGHT DISTRIBUTING HITCH SYSTEM INSTALLATION/OPERATION INSTRUCTIONS
ULTRA-FAB PRODUCTS, INC. 57985 St. Rd. 19 South, Elkhart, Indiana 46517 ULTRA WEIGHT DISTRIBUTING HITCH SYSTEM ULTRA WEIGHT DISTRIBUTING HITCH SYSTEM INSTALLATION/OPERATION INSTRUCTIONS ITEM # 1 EXPLODED
More informationRhino Long Travel Spindle Kit Yamaha Rhino FTR10072
4331 EUCALYPTUS AVE. ~~ CHINO, CA 91710 909-597-7800 Fax 909-597-7185 Rhino Long Travel Spindle Kit 2005-08 Yamaha Rhino FTR10072 PARTS LIST: QTY. Part # Description 1 FTS95061D Rhino Spindle Driver 1
More informationInstallation Instructions
Installation Instructions AMP RESEARCH Power Step by Bestop Automatic Retracting Running Board Vehicle Application Nissan Titan King Cab 2004 and newer (5 ft.) Part Number: 75106-01 Nissan Titan Crew Cab
More informationINSTALLATION/OPERATION
INSTALLATION/OPERATION ULTRA POWER TWIN II-30 P/N 39-941705 APPLICATION The primary purpose of your Power Twin II is to provide rock solid stabilization for maximum comfort while using your RV in a parked
More informationInstallation Instructions. QuickSilver Shifter. Fits: GM, Ford, Chrysler Transmissions See Application Guide for Specific Applications Part # 80683
Installation Instructions QuickSilver Shifter Fits: GM, Ford, Chrysler Transmissions See Application Guide for Specific Applications Part # 80683 WORK SAFELY! For maximum safety, perform this installation
More information