GT-R MIL ON WITH DTC P0729/P2832 STORED
|
|
|
- Sydney Lucas
- 5 years ago
- Views:
Transcription
1 Classification: Reference: Date: AT NTB February 18, GT-R MIL ON WITH DTC P0729/P2832 STORED APPLIED VEHICLE: GT-R (R35) IF YOU CONFIRM For The MIL is on and DTC P0729 (6GR Incorrect Ratio) is stored, For The MIL is on and DTC P0729 (Sleeve A1 Function) is stored, For The MIL is on and DTC P2832 (Shift Fork A) is stored, ACTION Install Metal Caps on 3 of the shift pistons in the transmission Actuator Control Module (ACM). Metal Caps are listed in the Parts Information. Refer to the Service Procedure for Metal Cap installation. IMPORTANT: The purpose of ACTIONS (above) is to give you a quick idea of the work you will be performing. You MUST closely follow the entire SERVICE PROCEDURE as it contains information that is essential to successfully completing this repair. Nissan Bulletins are intended for use by qualified technicians, not 'do-it-yourselfers'. Qualified technicians are properly trained individuals who have the equipment, tools, safety instruction, and know-how to do a job properly and safely. NOTE: If you believe that a described condition may apply to a particular vehicle, DO NOT assume that it does. See your Nissan dealer to determine if this applies to your vehicle. 1/13
2 PARTS INFORMATION DESCRIPTION P/N QUANTITY Metal Cap (1) KB50A 3 O-ring Seal (1) JF02A 1 O-ring Seal (1) JF03A 1 O-ring Seal (1) JF04A 1 Fill Plug Washer N200 1 Drain Plug JF00E 1 Transmission Oil Pan Gasket JF00A 1 Transmission oil (2) 999MP - GTRT00P 9 qt (1) The Metal cap and O-ring seals were added to the GT-R restricted parts list. Nissan Parts and Service Bulletin titled 2010 Nissan GT-R Unique Service Requirements explains the restricted parts of the GT-R and how these parts can be ordered. (2) Order this item through the Nissan Maintenance Advantage program: Phone: 877-NIS- NMA1 ( ), Fax , Website order via link on dealer portal and click on Tire Advantage link or order direct at CLAIMS INFORMATION Submit a Primary Part (PP) type line claim using the following claims coding: DESCRIPTION PFP OP CODE SYM DIA FRT Install ACM Piston Covers (Metal Caps) 320A0-JF00A JX13AA HD hrs. REQUIRED SPECIAL TOOL (J ACM Holding Pins) 2/13 NTB11-011
3 SERVICE PROCEDURE CAUTION: Do not use fabric gloves or cloth rags that will shed lint or fibers while working with internal transmission components. Be careful not to introduce any contaminants into the transmission. To prevent burns, make sure the transmission and transmission oil temperature is below 40 C (104 F) before beginning work. 1. Remove the front diffuser (cover under the transmission). If needed, refer to section EXT in the Service Manual. 2. Drain the transmission oil. If needed, refer to section TM in the Service Manual. 3. Remove the transmission oil pan. If needed, refer to section TM in the Service Manual. 4. Remove the transmission suction filter. Suction Filter a. Hold the filter with both hands as shown. b. Carefully move the filter back and forth while pulling down. Figure 1 3/13 NTB11-011
4 5. Disconnect the 2 harness connectors shown in Figure 2. Connectors Figure 2 6. Disconnect the main harness connector shown in Figure 3. Main harness Connector Figure 3 7. Disconnect the harness connector shown in Figure 4. Figure 4 4/13 NTB11-011
5 8. Remove the bracket bolt shown in Figure 5. Temp sensor Bolt Harness is pulled back Figure 5 9. Take the temperature sensor loose from the metal bracket. Temp sensor Metal bracket Figure Remove the bracket bolt shown in Figure 7. Electrical connector 11. Disconnect the electrical connector shown in Figure 7. Bolt Figure 7 5/13 NTB11-011
6 12. Install holding pins (special tool J-50392) into the holes shown in Figure 8. ACM NOTE: These retaining pins will prevent rotation of the ACM shift pistons. Figure 8 Make sure the holding pins are very close (almost touching) the ACM. Holding pins almost touching It may require some wiggling of the holding pins, while gently pushing them in, to get them lined up correctly and go all the way in. Figure 9 If there is a gap between the holding pin and the ACM, the holding pin is not in all the way. NG NOTE: If you are unable to get the holding pins all the way in, continue with the procedure. Once the ACM is removed, use the holding pin installation procedure at the end of the bulletin. Figure 10 6/13 NTB11-011
7 13. Remove the ACM from the transmission. Remove only the 5 bolts (T30 Torx ) circled in Figure 11. CAUTION: Remove only the bolts circled in Figure 11. Removal or loosening of any other ACM bolts will make the ACM unusable. Do Not use power tools. Do Not use fabric gloves. Use only lint free rags. The ACM is heavy (5 kg / 11 lb), make sure to properly hold it (support it) while removing the bolts. Figure 11 7/13 NTB11-011
8 14. Set the ACM in a clean working area. CAUTION: Do Not use fabric gloves. Use only lint free rags. Do NOT clean debris off of the pistons. Any wiping or cleaning of the pistons will scratch the piston coating. Do not wipe, touch, or in anyway clean the debris off of the pistons. Debris on piston, do not clean Debris on piston, do not clean Figure 12 NOTE: If you were unable to install holding pins (special tool J-50392) into the ACM before removal: Go to Installing Holding Pins (special tool J-50392) on page 12. After the holding pins are installed, return here and continue with the procedure. 8/13 NTB11-011
9 15. Install a Metal Cap onto 3 of the ACM shift pistons. Make sure the notch is aligned with the retaining pins. Metal Cap Notch Notch Holding pin Figure 13 Install Metal Caps on the 3 pistons shown in Figure 14. DO NOT install Metal Cap on 3 rd -5 th piston Install Metal Cap on 1 st - reverse piston Install Metal Cap on 6 th piston Install Metal Cap on 2 nd 4 th piston Figure 14 9/13 NTB11-011
10 16. Remove old o-ring seals and install new o- ring seals on the transmission ports shown in Figure 15. If needed, use petroleum jelly to hold the seals in place for installation of the ACM. Ports Figure Reinstall the ACM into the transmission. Be careful not to damage harnesses or connectors. Tighten the bolts in the order shown in Figure 16. Bolt torque: N m ( kg-m, in-lb) Figure 16 10/13 NTB11-011
11 18. Remove the holding pins from the ACM. 19. Reconnect the harness connectors and install bracket bolts in reverse order. Bracket bolt torque: 9.5 N m (0.97 kg-m, 84 in-lb) 20. Reinstall the suction filter. Make sure the edge of the suction filter is aligned with the edge of the transmission case. Install the suction filter; push here until it stops Figure Reinstall the transmission oil pan. Use a new gasket. Bolt torque: 8.5 N m (0.87 kg-m, 75 in-lb). 22. Refill the transmission oil. If needed, refer to section TM in the Service Manual. 23. Use CONSULT-III to perform Clutch Learning before test driving. 24. Test drive the vehicle; make sure the transmission is operating correctly. 25. Make sure there is no transmission oil leaks. 26. Reinstall the front diffuser (cover under the transmission). 11/13 NTB11-011
12 Installing Holding Pins (Special Tool J-50392) NOTE: This operation is required ONLY when the holding pins could not be completely installed before removal of the ACM from the transmission. 1. Locate the magnets inside the shift pistons. NOTE: The shift pistons have magnets inside them that must be aligned with the sensors on the outside of the pistons (see Figure A). The magnet location can be determined in two ways: Fine metal debris buildup at the magnet locations (see Figure A). Hold a pocket magnet next to the piston. The pocket magnet will be repelled (pushed away) when it is next to the magnet inside the shift piston. Pocket magnet pushed away when next to location of piston magnet. Shift sensor Debris accumulated at magnet location Figure A NOTE: Do not wipe the shift pistons or in any way clean off the fine metal debris. 2. Rotate the shift pistons so the magnet locations line up with the shift sensors (see Figure A above and Figure C on the next page). 12/13 NTB11-011
13 3. Hold the shift pistons in place while carefully inserting the holding pin into the valve body (see Figure B). Carefully insert the holding pin. Do Not hit the sides of the shift piston with the holding pin. Insert holding pin Hold pistons in place Figure B Shift Sensors Aligned With Piston Magnets Shift sensor Magnet Magnet Magnet Shift sensor Shift sensor Shift sensor Magnet Shift sensor Figure C Magnet 13/13 NTB11-011
2007 MAXIMA; MIL 'ON' W/DTC P0840 OR P0845
Classification: Reference: Date: AT08-001 NTB08-042 April 3, 2008 2007 MAXIMA; MIL 'ON' W/DTC P0840 OR P0845 APPLIED VEHICLE: 2007 Maxima (A34) IF YOU CONFIRM The MIL is ON with one of the following DTC
SENTRA; REDUCED PERFORMANCE DUE TO CVT FLUID TEMPERATURE PROTECTION LOGIC
Classification: Reference: Date: AT16-017 NTB16-113 November 15, 2016 2011-2012 SENTRA; REDUCED PERFORMANCE DUE TO CVT FLUID TEMPERATURE PROTECTION LOGIC APPLIED VEHICLE: APPLIED ENGINE: 2011-2012 Sentra
Technical Bulletin. Reference: NTB15-087a CVT WITH 4 CYLINDER ENGINE VALVE BODY REPLACEMENT WITH CONFIRMED DTC
2014 Nissan-Datsun Altima Sedan L4-2.5L (QR25DE) Vehicle > ALL Diagnostic Trouble Codes ( DTC ) > Technical Service Bulletins CVT WITH 4 CYLINDER ENGINE VALVE BODY REPLACEMENT WITH CONFIRMED DTC Technical
ROGUE AND ROGUE SELECT; REDUCED PERFORMANCE DUE TO CVT FLUID TEMPERATURE PROTECTION LOGIC
Classification: Reference: Date: AT16-013 NTB16-090 September 9, 2016 2011-2015 ROGUE AND ROGUE SELECT; REDUCED PERFORMANCE DUE TO CVT FLUID TEMPERATURE PROTECTION LOGIC APPLIED VEHICLES: 2011-2013 Rogue
2009 MAXIMA STEERING COLUMN COMFORT ADJUSTMENT
Classification: Reference: Date: ST09-005 NTB09-094 September 23, 2009 2009 MAXIMA STEERING COLUMN COMFORT ADJUSTMENT APPLIED VEHICLES: 2009 Maxima (A35) IF YOU CONFIRM The steering column power adjustment
PATHFINDER, QUEST, MURANO, MAXIMA, ALTIMA V6 CVT JUDDER AND DTC P17F0 OR P17F1 STORED
Classification: Reference: Date: APPLIED VEHICLE: AT15-005b NTB15-015b September 10, 2015 PATHFINDER, QUEST, MURANO, MAXIMA, ALTIMA V6 CVT JUDDER AND DTC P17F0 OR P17F1 STORED This bulletin has been amended
VERSA; CANNOT REMOVE KEY FROM IGNITION
Classification: Reference: Date: EL09-040 NTB09-137 December 2, 2009 VERSA; CANNOT REMOVE KEY FROM IGNITION This bulletin supersedes NTB08-071. Discard all of its copies. APPLIED VEHICLE: 2007 2010 Versa
SENTRA; LONG ENGINE CRANK TIME BEFORE START
Classification: Reference: Date: EC05-001a NTB05-052a September 8, 2006 2002 2006 SENTRA; LONG ENGINE CRANK TIME BEFORE START APPLIED VEHICLES: 2002 Sentra (B15) with QR25 engine only. 2003 2006 Sentra
FX35; DTC P0300 AND IGNITION COILS BLISTERED
Classification: Reference: Date: EC11-007 ITB11-017 March 1, 2011 2003 2008 FX35; DTC P0300 AND IGNITION COILS BLISTERED APPLIED VEHICLES: 2003 2008 FX35 (S50) IF YOU CONFIRM Cylinder Misfire DTC (P0300
MAXIMA; MIL ON WITH DTC S P0014, P0024
Classificatio n: Reference: Date: EC12-026 NTB12-116 December 17, 2012 2009-2012 MAXIMA; MIL ON WITH DTC S P0014, P0024 APPLIED VEHICLE: 2009-2012 Maxima (A35) IF YOU CONFIRM MIL is on with DTC s P0014
G35; CLICKING NOISE FROM REAR AXLES
Classification: Reference: Date: RA04-004b ITB05-002b November 9, 2005 2003 2005 G35; CLICKING NOISE FROM REAR AXLES This bulletin has been amended. The Service Procedure has been revised. No other content
MAXIMA; ABS ACTIVATES WITH NORMAL BRAKING / ABS WARNING LAMP IS ON
Classification: Reference: Date: BR06-011b NTB07-016b July 10, 2007 2004 2007 MAXIMA; ABS ACTIVATES WITH NORMAL BRAKING / ABS WARNING LAMP IS ON The Parts Information section of this bulletin has been
MIL ON WITH P0840/P0845 AND P0710
Classification: Reference: Date: AT09-002a NTB09-044a August 26, 2011 MIL ON WITH P0840/P0845 AND P0710 This bulletin has been amended. ACTIONS, the NOTE under PARTS INFORMATION, a portion of the repair
GT-R RATTLE FROM FLYWHEEL HOUSING
Classification: Reference: Date: AT09-010 NTB09-147 December 18, 2009 2009 2010 GT-R RATTLE FROM FLYWHEEL HOUSING APPLIED VEHICLES: 2009 2010 GT-R (R35) IF YOU CONFIRM A rattle noise coming directly from
ALTIMA SEDAN, COUPE, AND HYBRID; ENGINE NO CRANK / NO START
Classification: Reference: Date: EL10-030 NTB10-139 November 23, 2010 ALTIMA SEDAN, COUPE, AND HYBRID; ENGINE NO CRANK / NO START APPLIED VEHICLES: 2007 2010 Altima Sedan (L32) with CVT only 2008 2010
ALTIMA SEDAN; SLIGHT DRIVER'S POWER SEAT MOVEMENT SIDE-TO-SIDE
Classification: Reference: Date: BT08-025b NTB08-089b November 12, 2009 2007-2010 ALTIMA SEDAN; SLIGHT DRIVER'S POWER SEAT MOVEMENT SIDE-TO-SIDE The ACTION statement, Applied Vehicles/VINs/Dates/, Parts
2007 SENTRA & VERSA; DTC P0031, P2A00, P1148
Classification: Reference: Date: EC08-017a NTB08-074a April 27, 2009 2007 SENTRA & VERSA; DTC P0031, P2A00, P1148 This bulletin has been amended. The Claims Information and Service Procedure have been
ALTIMA; CVT DELAYED ENGAGEMENT WHEN SHIFTING INTO DRIVE OR REVERSE
Classification: Reference: Date: AT15-014b NTB15-085b April 1, 2016 2013-2015 ALTIMA; CVT DELAYED ENGAGEMENT WHEN SHIFTING INTO DRIVE OR REVERSE This bulletin has been amended. Instructions have been changed
EXHAUST RATTLE / BUZZING NOISE
Classification: Reference: Date: EM05-003e NTB05-021e March 10, 2010 EXHAUST RATTLE / BUZZING NOISE This bulletin has been amended. The title, ACTIONS, PARTS INFORMATION, and the SERVICE PROCEDURE have
ALTIMA; MIL ON P1273 (QR25 ENGINE) MAY BE CAUSED BY THE REAR O2 SENSOR
Classification: Reference: Date: EC05-016a NTB06-039a May 17, 2006 2004 2005 ALTIMA; MIL ON P1273 (QR25 ENGINE) MAY BE CAUSED BY THE REAR O2 SENSOR This bulletin has been amended. The Claims Information
FRONTIER WITH QR25 ENGINE; DTC P0420 (TW CATALYST SYS-B1) STORED IN THE ECM
Classification: Reference: Date: EC10-008 NTB10-045 March 19, 2010 2005-2006 FRONTIER WITH QR25 ENGINE; DTC P0420 (TW CATALYST SYS-B1) STORED IN THE ECM APPLIED VEHICLE: 2005-2006 Frontier (D40) APPLIED
2013 ALTIMA SEDAN WITH 4 CYL ENGINE; MIL ON WITH A/F SENSOR DTC STORED
Classificatio n: Reference: Date: EC12-024b NTB12-085b April 4, 2013 2013 ALTIMA SEDAN WITH 4 CYL ENGINE; MIL ON WITH A/F SENSOR DTC STORED This bulletin has been amended in several areas to remove V6
2013 ALTIMA V6 SEDAN AND PATHFINDER SHUDDER FROM TORQUE CONVERTER LOCK UP CLUTCH
Classification: Reference: Date: AT13-007a NTB13-064a June 13, 2013 2013 ALTIMA V6 SEDAN AND PATHFINDER SHUDDER FROM TORQUE CONVERTER LOCK UP CLUTCH This bulletin has been amended to correct a typographical
TITAN AND ARMADA DRIVER SIDE AIR MIX DOOR MOTOR REPLACEMENT
Classification: Reference: Date: HA11-004 NTB11-048 May 5, 2011 2004 2011 TITAN AND ARMADA DRIVER SIDE AIR MIX DOOR MOTOR REPLACEMENT APPLIED VEHICLE: 2004 2011 Titan (A60) 2004 2011 Armada (TA60) IF YOU
MAXIMA DRIVER'S POWER SEAT WILL NOT MOVE FORWARD OR BACKWARD
Classification: Reference: Date: EL01-030d NTB02-001d December 21, 2004 2000-2003 MAXIMA DRIVER'S POWER SEAT WILL NOT MOVE FORWARD OR BACKWARD This bulletin amends NTB02-001. The Applied Vehicles have
ALTIMA V6 SEDAN AND PATHFINDER; JUDDER DURING LIGHT ACCELERATION
Classificatio n: Reference: Date: AT13-017 NTB13-086 September 10, 2013 2013-2014 ALTIMA V6 SEDAN AND PATHFINDER; JUDDER DURING LIGHT ACCELERATION APPLIED VEHICLES, VINS AND DATES: APPLIED TRANSMISSION:
2011 M; NO START AND / OR BATTERY LOW VOLTAGE DUE TO INTELLIGENT KEY AND WELCOME LIGHTING
Classification: Reference: Date: EL11-010 ITB11-029 May 2, 2011 2011 M; NO START AND / OR BATTERY LOW VOLTAGE DUE TO INTELLIGENT KEY AND WELCOME LIGHTING APPLIED VEHICLE : 2011 M37 and M56 (Y51) APPLIED
REMOVAL PROCEDURE FOR SEIZED EXHAUST SENSOR
Classification: Reference: Date: EM09-015 NTB10-009 January 19, 2010 REMOVAL PROCEDURE FOR SEIZED EXHAUST SENSOR APPLIED VEHICLES: All Nissan vehicles SERVICE INFORMATION If an exhaust sensor is seized
QUEST; WATER LEAK IN CARGO AREA
Classification: Reference: Date: BT05-018 NTB05-049 June 22, 2005 2004 2005 QUEST; WATER LEAK IN CARGO AREA APPLIED VEHICLES: 2004 2005 Quest (V42) IF YOU CONFIRM IF YOU CONFIRM Rear Cargo Area Water is
SUNROOF RAIL ASSEMBLY REPAIR
Classification: Reference: Date: BT99-049 NTB00-001 December 15, 1999 SUNROOF RAIL ASSEMBLY REPAIR APPLIED VEHICLES: 1995-97 Maxima (A32) 1996-99 Pathfinder (R50) SERVICE INFORMATION If an applied vehicle
2007 ALTIMA AND SENTRA; DTC P0128 THERMOSTAT FUNCTION
Classification: Reference: Date: EC07-001a NTB07-020a April 23, 2007 2007 ALTIMA AND SENTRA; DTC P0128 THERMOSTAT FUNCTION This bulletin has been amended. Applied Vehicles has been amended to exclude Altima
EX35, G35, G37; STEERING WHEEL SWITCH FINISHER SERVICE PARTS
Classification: Reference: Date: ST12-006 ITB12-050 August 14, 2012 EX35, G35, G37; STEERING WHEEL SWITCH FINISHER SERVICE PARTS APPLIED VEHICLES: 2007-2008 G35 Sedan (V36) 2009-2012 G37 Sedan (V36) 2008-2013
2004 TITAN AND ARMADA; MIL "ON" WITH DTC P1031, P1051, P1148, P1168 A/F SENSOR HEATER / CLOSED LOOP
Classification: Reference: Date: EC04-008a NTB04-032a October 29, 2004 2004 TITAN AND ARMADA; MIL "ON" WITH DTC P1031, P1051, P1148, P1168 A/F SENSOR HEATER / CLOSED LOOP This bulletin amends NTB04-032.
PROCEDURE TO COMPLETE IAVL WHEN IDLE SPEED NEEDS TO BE REDUCED.
Classification: Reference: Date: EC05-009 NTB05-067 October 5, 2005 PROCEDURE TO COMPLETE IAVL WHEN IDLE SPEED NEEDS TO BE REDUCED. APPLIED VEHICLES: All 2002 2005 models IF YOU CONFIRM The idle, in Park
QUEST; REVISED SLIDING DOOR INITIALIZATION PROCEDURE
Classification: Reference: Date: BT04-043 NTB04-125 October 26, 2004 2004-2005 QUEST; REVISED SLIDING DOOR INITIALIZATION PROCEDURE APPLIED VEHICLES: 2004 2005 Quest (V42) with power sliding doors. IF
PATHFINDER / XTERRA / FRONTIER; BUZZING / WHINING NOISE FROM TIMING CHAIN AREA
Classification: Reference: Date: EM09-007a NTB09-128a May 25, 2010 PATHFINDER / XTERRA / FRONTIER; BUZZING / WHINING NOISE FROM TIMING CHAIN AREA This bulletin has been amended. PARTS INFORMATION and CLAIMS
2007 G35; CRUISE CONTROL SYMPTOMS WHEN TRAVELING DOWNHILL
Classification: Reference: Date: EL07-022a ITB07-028a October 24, 2007 2007 G35; CRUISE CONTROL SYMPTOMS WHEN TRAVELING DOWNHILL The Applied VIN/Date, ACTION, Parts Information, Claims Information, Service
MIL ON WITH DTC P0102/P1102 (MASS AIRFLOW SENSOR MAFS) STORED
Classification: Reference: Date: EC02-026 NTB02-109 November 5, 2002 MIL ON WITH DTC P0102/P1102 (MASS AIRFLOW SENSOR MAFS) STORED APPLIED VEHICLE: 2002 Maxima (A33) APPLIED DATE: Vehicles built before
MURANO; AUTOMATIC BACK DOOR DOES NOT OPERATE AND RELATED DTCS
Classification: Reference: Date: BT15-020b NTB15-073b March 22, 2016 2015-2016 MURANO; AUTOMATIC BACK DOOR DOES NOT OPERATE AND RELATED DTCS This bulletin has been amended. Changes have been made to all
QX4; DRIVER'S SEAT (WITH ADP ONLY) WON'T MOVE FORWARD OR BACKWARD
Classification: Reference: Date BT00-030a ITB00-065a December 21, 2004 2001 2003 QX4; DRIVER'S SEAT (WITH ADP ONLY) WON'T MOVE FORWARD OR BACKWARD This bulletin amends ITB00-065. This version amends the
MAXIMA A/T SHIFT CONTROL DEVICE - HARD TO SHIFT
Classification: Reference: Date: AT99-001a NTB99-014a June 19, 2000 1998-1999 MAXIMA A/T SHIFT CONTROL DEVICE - HARD TO SHIFT This bulletin amends NTB99-014 and includes updated Service and Warranty Information.
G COUPE AND SEDAN; BRAKE JUDDER
Classification: Reference: Date: BR09-002b ITB09-037b January 28, 2010 G COUPE AND SEDAN; BRAKE JUDDER This bulletin has been amended. CLAIMS INFORMATION has been corrected. The SERVICE PROCEDURE has been
ALIGNMENT AND ROAD CROWN
Classification: Reference: Date: ST08-001 NTB08-097 October 9, 2008 ALIGNMENT AND ROAD CROWN APPLIED VEHICLES: All Nissan - except GT-R SERVICE INFORMATION Customers may report that their vehicle pulls
WITHOUT NAVIGATION SYSTEM HANDS-FREE PHONE POOR SOUND QUALITY
Classification: Reference: Date: EL12-064b ITB12-062b October 25, 2012 WITHOUT NAVIGATION SYSTEM HANDS-FREE PHONE POOR SOUND QUALITY This bulletin has been amended. Changes have been made throughout to
I30 MIL "ON" WITH DTC P0420 STORED - THREE WAY CATALYST FUNCTION
Classification: Reference: Date: EC00-025b ITB00-054b June 7, 2004 2000-2001 I30 MIL "ON" WITH DTC P0420 STORED - THREE WAY CATALYST FUNCTION IMPORTANT: THIS BULLETIN HAS BEEN REVISED. The Service Information
SUNROOF SUNSHADE FABRIC WORN/RIPPED
AMClassification: Reference: Date: BT04-055 NTB05-016 February 24, 2005 SUNROOF SUNSHADE FABRIC WORN/RIPPED APPLIED VEHICLE: APPLIED VIN: 2004 Titan (A60) Crew Cab ONLY 2004 Armada (TA60) Titan: Vehicles
Vehicle Level Technical Service Bulletins All Technical Service Bulletins Engine Controls - Engine Idle Speed 25RPM Too High
Select Vehicle New TSBs Technician's Reference Component Search: Conversion Calculator 2005 Nissan-Datsun Maxima V6-3.5L (VQ35) Vehicle Level Technical Service Bulletins All Technical Service Bulletins
MAXIMA DRIVER'S POWER SEAT WILL NOT MOVE FORWARD OR BACKWARD TECHNICAL SERVICE BULLETIN
Page 1 of 11 2000-2003 MAXIMA DRIVER'S POWER SEAT WILL NOT MOVE FORWARD OR BACKWARD TECHNICAL SERVICE BULLETIN Reference Number(s): NTB02-001d, Date of Issue: December 21, 2004 NISSAN: 2000-2003 Maxima
2002 ALTIMA; MANUAL A/C TEMPERATURE NOT ADJUSTABLE
Classification: Reference: Date: HA02-003 NTB02-048 June 12, 2002 2002 ALTIMA; MANUAL A/C TEMPERATURE NOT ADJUSTABLE APPLIED VEHICLE: APPLIED VIN: 2002 Altima (L31) with Manual A/C ONLY All vehicles built
EM06-004b NTB06-072b September 3, 2009 DRIVE BELT NOISE
Classification: Reference: Date: EM06-004b NTB06-072b September 3, 2009 DRIVE BELT NOISE This bulletin has been amended. The Service Procedure, Applied Vehicles / VIN / Date, ACTION, and Claims Information
2005 Nissan Quest QUEST; WATER LEAK IN CARGO AREA QUEST; WATER LEAK IN CARGO AREA TECHNICAL SERVICE BULLETIN
TECHNICAL SERVICE BULLETIN Reference Number(s): NTB05-049, Date of Issue: June 22, 2005 NISSAN: 2004-2005 Quest CLASSIFICATION: BT05-018 APPLIED VEHICLES: 2004-2005 Quest (V42) IF YOU CONFIRM Water is
MAXIMA MIL "ON" WITH FRONT O2 SENSOR DTC P0134, P0135, P0154, OR P0155
Classification: Reference: Date: EC01-029 NTB02-002 January 1, 2002 2000-2001 MAXIMA MIL "ON" WITH FRONT O2 SENSOR DTC P0134, P0135, P0154, OR P0155 APPLIED VEHICLES: 2000-2001 Maxima (A33) SERVICE INFORMATION
CLUNK, RATTLE, OR KNOCKING NOISE FROM REAR BRAKE CALIPER
Classification: Reference: Date BR01-001A NTB01-069A March 7, 2002 CLUNK, RATTLE, OR KNOCKING NOISE FROM REAR BRAKE CALIPER This bulletin amends NTB01-069. This version includes additional Model and Model
SB Service Bulletin
SB-10052924-4799 Service Bulletin Applies To: 2013 Pilot 2WD From VIN 5FNYF3...DB014058 thru 5FNYF3...DB025447 2013 Pilot 4WD From VIN 5FNYF4...DB025128 thru 5FNYF4...DB048530 13-055 July 19, 2013 MIL
ECM REPLACEMENT PROCEDURES
Classification: Reference: Date: EC00-007c NTB00-052c April 16, 2004 ECM REPLACEMENT PROCEDURES ATTENTION: THIS BULLETIN HAS BEEN REVISED. The Service Procedures for replacing an ECM on an Applied vehicle
2001 MAXIMA ALARM SOUNDS AFTER 30 MINUTES AND/OR TRUNK LAMP INOPERATIVE
Classification: Reference: Date: EL0-00 NTB0-009 February 9, 00 00 MAXIMA ALARM SOUNDS AFTER 30 MINUTES AND/OR TRUNK LAMP INOPERATIVE APPLIED VEHICLES: 00 Maxima (A33) APPLIED VINS: Vehicles built before:
Service Bulletin 1988 PRELUDE. RECALL: 1988 Prelude Power Steering Supply Hose
Service Bulletin Model Applicable To File Under Bulletin No. 1988 PRELUDE See VEHICLES AFFECTED ENGINE 88-014 Issue Date APRIL 20, 1988 RECALL: 1988 Prelude Power Steering Supply Hose PROBLEM When subjected
Mazda North American Operations Irvine, CA
Service Bulletin Mazda North American Operations Irvine, CA 92618-2922 Subject: MIL ON - P2070 SET Bulletin No: 01-019/08 2004-2007 RX-8 - MIL ON - P2070 SET BULLETIN NOTE This bulletin supersedes the
Authorized Field Change
Authorized Field Change AFC 08907R Date: June, 2008 Subject File: ENGINE Subject: Fuel Pressure Regulator and Fuel Pressure Switch on VT 275 Engines in Workhorse Commercial Chassis Model: Workhorse Start
2003 G35 SEDAN; NOISE FROM ENGINE AREA WITH A/C ON
Classification: Reference: Date: HA02-005b ITB02-056b December 5, 2003 2003 G35 SEDAN; NOISE FROM ENGINE AREA WITH A/C ON This bulletin contains amended Applied VIN. Please discard all previous copies
Installation Instructions for Series 3100V Low Level Indicator
Instruction Sheet P/N Installation Instructions for Series 3100V Low Level Indicator WARNING: Allow only qualified personnel to perform the following tasks. Follow the safety instructions in this document
ALL NISSAN; BRAKE NOISE/JUDDER/PEDAL FEEL DIAGNOSIS AND REPAIR
Classification: Reference: Date: BR00-004e NTB00-033e July 23, 2013 ALL NISSAN; BRAKE NOISE/JUDDER/PEDAL FEEL DIAGNOSIS AND REPAIR This bulletin has been amended to include vehicles built up to the publication
ALTIMA; POOR HEATER PERFORMANCE
Classification: Reference: Date: HA02-002b NTB02-047b September 9, 2003 2002 2003 ALTIMA; POOR HEATER PERFORMANCE This bulletin amends NTB02-047a. This version updates the Service Procedure. Please discard
Service Bulletin
Service Bulletin 13-082 May 18, 2015 51869-02164 Version 7 Warranty Extension: MIL Comes On With DTCs P0301 thru P0304 Supersedes 13-082, dated September 12, 2015, to revise the information highlighted
Z; BOSE AUDIO AMPLIFIER CUSTOMER SATISFACTION INITIATIVE
Classification: Reference: Date: EL03-026 NTB03-086 October 1, 2003 2003 350Z; BOSE AUDIO AMPLIFIER CUSTOMER SATISFACTION INITIATIVE IMPORTANT This bulletin supercedes bulletin NTB02-111a Refer to this
Service Bulletin
Service Bulletin 13-053 Applies To: See VEHICLES AFFECTED August 28, 2013 Surge, Hesitation, or Judder on Light Acceleration from a Stop (Supersedes 13-053, dated July 13, 2013, to revise the information
Service Bulletin. Fuel Fill Cap Binds and Possible MIL Comes On With DTC P1456 (Supersedes , dated January 30, 2004)
Service Bulletin 04-002 Applies To: See VEHICLES AFFECTED February 13, 2004 Fuel Fill Cap Binds and Possible MIL Comes On With DTC P1456 (Supersedes 04-002, dated January 30, 2004) SYMPTOM The fuel fill
Service Bulletin
Service Bulletin 13-080 February 03, 2018 08193 Version 7 Warranty Extension: MIL Comes On With DTCs P0301 thru P0304 Supersedes 13-080, dated May 18, 2016, to revise the information highlighted in yellow.
VOLUNTARY SERVICE CAMPAIGN ALTIMA; HALOGEN HEADLAMP GROUND PLATE KIT
Reference: NTB05-057b March 14, 2008 Date: VOLUNTARY SERVICE CAMPAIGN 2002 2003 ALTIMA; HALOGEN HEADLAMP GROUND PLATE KIT This bulletin amends NTB05-057a. The IMPORTANT statements on page 3 and page 20
Service Bulletin
Service Bulletin 13-081 February 03, 2018 08191 Version 13 Warranty Extension: MIL Comes On With DTCs P0301 thru P0304 Supersedes 13-081, dated January 23, 2018, to revise the information highlighted in
Mazda North American Operations Irvine, CA
Service Bulletin Mazda North American Operations Irvine, CA 92618-2922 Subject: HEAVY STEERING EFFORT WITH POWER STEERING MALFUNCTION INDICATOR LAMP ON AND DTC C1099 Bulletin No: 06-002/09 2007-2009 MAZDA3
Service Bulletin. Applies To: MDX ALL 2006 MDX From VIN 2HNYD18..6H thru 2HNYD18..6H535538
Service Bulletin Applies To: 2003 05 MDX ALL 2006 MDX From VIN 2HNYD18..6H500001 thru 2HNYD18..6H535538 06-028 July 13, 2007 MIL Comes On With DTC P0335, P0339, P0385, or P0389, and the Engine Runs Roughly
Service Manual. Climate Control Inc.
SECTION 2 Service - Clutch Servicing (Removal & Installation) - Shaft Seal Servicing (Removal & Installation) - Head & Valve Plate Servicing (Removal & Installation) - Baseplate Servicing (Removal & Installation)
VOLUNTARY SAFETY RECALL CAMPAIGN 2014 LEAF ; REPLACEMENT OF THE TRACTION MOTOR INVERTER
Reference: NTB14-046 May 22, 2014 Date: VOLUNTARY SAFETY RECALL CAMPAIGN 2014 LEAF ; REPLACEMENT OF THE TRACTION MOTOR INVERTER CAMPAIGN I.D. #: PC281 APPLIED VEHICLE: 2014 LEAF (ZE0) Check Service Comm
# D: No Reverse, Second Gear or Fourth Gear (Replace Reaction Sun Shell with More Robust Heat Treated Parts) - (Jun 10, 2008)
Page of 5 200 Chevrolet Astro - 4WD Astro, Safari (VIN M/L) Service Manual Document ID: 250887 #00-07-30-022D: No Reverse, Second Gear or Fourth Gear (Replace Reaction Sun Shell with More Robust Heat Treated
Page 1 of 7 Section 07-01A: Transmission, Automatic, E4OD IN-VEHICLE SERVICE 1993 Bronco/Econoline/F-Series Workshop Manual Valve Bodies and Intermediate Band Servo NOTE: If a transmission has been disassembled
Aftertreatment System December Removal of the 1-BOX from the Vehicle. Installation of the 1- BOX to the Vehicle
12 13-18 1 12 13-18 SUBJECT DATE Aftertreatment System December 2018 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change Removal of the 1-BOX from the Vehicle Installation
Service Bulletin
Service Bulletin 17-014 February 27, 2018 08343 Version 2 2016 17 Pilot: Judder from the Torque Converter Lock-Up Clutch (Snapshot Upload Required) Supersedes 17-014, 2016 17 Pilot: Judder from the Torque
Service Bulletin
Service Bulletin 16-062 November 2, 2016 05121 Version 1 2014 15 MDX: Judder from the Torque Converter Lock-Up Clutch AFFECTED VEHICLES Year Model Trim VIN Range 2014 15 MDX ALL ALL BACKGROUND A judder
Service Bulletin
Service Bulletin 05-019 Applies To: 2001 02 MDX ALL February 5, 2008 Warranty Extension: EGR Valve Contamination May Cause Engine Hesitation/Surge or DTC P1491 (Supersedes 05-019, dated July 20, 2005,
Service Bulletin
Service Bulletin 16-062 February 11, 2017 05595 Version 2 2012 15 MDX: Judder from the Torque Converter Lock-Up Clutch Supersedes 16-062, dated November 2, 2016, see REVISION SUMMARY AFFECTED VEHICLES
Engine - Timing Chain/Front Cover Revised Procedure Classification: EM98-009
1995 Nissan-Datsun 200SX L4-1597cc 1.6L DOHC MFI (GA16DE) Page 1 Technical Service Bulletin # 98-107 Date: 990111 Engine - Timing Chain/Front Cover Revised Procedure Classification: EM98-009 Reference:
MIL ON WITH DTC P0106 STORED
Classification: Reference: Date: EC12-010f ITB12-026f March 15, 2016 MIL ON WITH DTC P0106 STORED This bulletin has been amended to edit the part numbers in Table A on page 5 and remove 2010 G37 Convertible
Actions Required to Avoid Repeat Turbocharger Failures
SERVICE BULLETIN (Also applies to Mack Trucks Australia) (Supersedes SB214020 dated 7/26/04) Number: SB214020 Date: 07/21/05 Model: ASET, E-Tech Actions Required to Avoid Repeat Turbocharger Failures When
G37, M37, M56, AND QX56; MIL ON WITH DTC P0106 STORED
Classification: Reference: Date: EC12-010d ITB12-026d June 6, 2013 G37, M37, M56, AND QX56; MIL ON WITH DTC P0106 STORED This bulletin has been amended. The ECM P/N Table has been updated. No other changes
BATTERY TESTING: NISSAN ORIGINAL EQUIPMENT AND GENUINE NISSAN REPLACEMENT BATTERIES
Classification: Reference: Date: EL99-016k NTB99-048k October 7, 2004 BATTERY TESTING: NISSAN ORIGINAL EQUIPMENT AND GENUINE NISSAN REPLACEMENT BATTERIES This bulletin has been amended. Please discard
TECHNICAL INSTRUCTIONS FOR SAFETY RECALL ALE VALVE SPRING AND LASH ADJUSTER REPLACEMENT GS 350: IS 350:
TECHNICAL INSTRUCTIONS FOR SAFETY RECALL ALE VALVE SPRING AND LASH ADJUSTER REPLACEMENT GS 350: 2007 2008 IS 350: 2006 2008 I. OPERATION FLOWCHART Verify Vehicle Eligibility 1. Check the VIN range. 2.
CHANGING AUTOMATIC TRANSMISSION FLUID
CHANGING AUTOMATIC TRANSMISSION FLUID Changing your automatic transmission fluid yourself is a quick and simple process when you know how! To help you out, we ve put together a quick step-by-step guide
Document ID: General Motors Corporation. All rights reserved.
Page 1 of 7 Document ID: 1274962 #02-06-01-016A: (MIL) Service Engine Soon Telltale Illuminated With DTCs P0171 and/or P0174 (Retorque Intake Manifold Vacuum Chamber Bolts, Install Vacuum Chamber Springs)
Service Bulletin. Applies To: Odyssey ALL 2010 Odyssey From VIN 5FNRL3...AB thru 5FNRL3...AB028891
Service Bulletin Applies To: 2007 09 Odyssey ALL 2010 Odyssey From VIN 5FNRL3...AB000001 thru 5FNRL3...AB028891 10-042 May 16, 2012 Clunking, Popping, or Clicking While Turning (Supersedes 10-042, dated
SYSTEM READINESS TEST (SRT) DRIVE PATTERNS
Classification: Reference: Date: EC98-001f NTB98-018f November 7, 2012 SYSTEM READINESS TEST (SRT) DRIVE PATTERNS This bulletin has been amended. Several Changes were made on page 9. Please discard all
Automotive FORENZA / RENO October 6, 2014 Technical Service Bulletin Engine Bulletin No. TS R1
Service Automotive FORENZA / RENO October 6, 2014 SUBJECT: MODEL(S): YEAR: Revisions: Throttle Position Sensor Replacement Forenza (RQ420) Reno (RQ420) 2006 2008 Forenza 2006 2008 Reno R1-10/08/14. This
SENTRA; HEATER CASE DOORS BECOME STUCK
Classification: Reference: Date HA02-008a NTB03-005a February 26, 2003 2002-2003 SENTRA; HEATER CASE DOORS BECOME STUCK The Service Procedure section of this bulletin has been amended to include additional
Service Bulletin Chirp From the Timing Belt Area (Supersedes , dated May 21, 2010, to revise the information marked by the black bars)
Service Bulletin 08-031 Applies To: See VEHICLES AFFECTED February 17, 2011 Chirp From the Timing Belt Area (Supersedes 08-031, dated May 21, 2010, to revise the information marked by the black bars) REVISION
TECHNICAL BULLETIN No:
CIRCULATE TO: TECHNICAL BULLETIN No: Date: 20 MAY 2010 SERVICE PARTS WARRANTY BODY SHOP THIS BULLETIN SUPERSEDES LA501-12; CHANGES ARE LIMITED TO INSTRUCTING TECHNICIANS TO CARRY OUT THIS REPAIR PROCEDURE
# H: Use of "Surface Conditioning Disks" When Cleaning Gasket Sealing Surfaces and/or Reused Parts - (Sep 12, 2017)
Page 1 of 5 Document ID: 4861675 #00-06-01-012H: Use of "Surface Conditioning Disks" When Cleaning Gasket Sealing Surfaces and/or Reused Parts - (Sep 12, 2017) Subject: Use of "Surface Conditioning Disks"
DTC P0340 CMP SENSOR (PHASE) DTC No. Trouble diagnosis name DTC detecting condition Possible cause
DTC P0340 CMP SENSOR (PHASE) Component Description DTC P0340 CMP SENSOR (PHASE) The camshaft position sensor (PHASE) senses the retraction with intake valve camshaft to identify a particular cylinder.
1998 Contour/Mystique Workshop Manual
SECTION 30-01: Automatic Transmission/Transaxle 1998 Contour/Mystique Workshop Manual IN-VEHICLE REPAIR Procedure revision date: 09/14/2001 Main Controls Special Tool(s) Aligner, Selector Shaft 30-S290
SYSTEM READINESS TEST (SRT) DRIVE PATTERNS
Classification: Reference: D ate: EC98-001g NTB98-018g June 7, 2013 SYSTEM READINESS TEST (SRT) DRIVE PATTERNS This bulletin has been amended. Additional changes were made on page 9. Please discard all
Emissions - Refuel Vapor Control Valve Damaged/MIL ON Section Title: Engine TSB No. TS R
1999 Suzuki Esteem GL Sedan L4-1.8L Page 1 Technical Service Bulletin # TS02R Date: 020308 Emissions - Refuel Vapor Control Valve Damaged/MIL ON Section Title: Engine TSB No. TS 02 03082R Division: Automotive