VOLUNTARY SERVICE CAMPAIGN ALTIMA; HALOGEN HEADLAMP GROUND PLATE KIT
|
|
- Silas Snow
- 6 years ago
- Views:
Transcription
1 Reference: NTB05-057b March 14, 2008 Date: VOLUNTARY SERVICE CAMPAIGN ALTIMA; HALOGEN HEADLAMP GROUND PLATE KIT This bulletin amends NTB05-057a. The IMPORTANT statements on page 3 and page 20 have been added. Page 10 of the Service Procedure, section Inspect Reflector Housings (left or right side), has been revised. The Parts Information has changed. Please discard all copies of earlier versions. CAMPAIGN ID #: PB135 APPLIED VEHICLES: Altima (L31) APPLIED VINs: 2002 models 1N4(*)L11(**)2C to models 1N4(*)L11(**)3C to APPLIED DATE: Vehicles built before March 19, 2003 INTRODUCTION Nissan has determined that on some 2002 and 2003 model year Nissan Altima vehicles, there is a possibility that a low beam Halogen headlamp bulb may fail to illuminate due to a poor ground contact. To prevent this from occurring, Nissan is conducting a Service Campaign to inspect the headlamp assemblies and then install a halogen terminal ground plate kit and, if needed, install a new low beam halogen bulb. In a limited number of cases, the headlamp assembly may require replacement. IDENTIFICATION NUMBER Nissan has assigned identification number PB135 to this campaign. This number must appear on all communications and documentation of any nature dealing with this campaign. NUMBER OF VEHICLES POTENTIALLY AFFECTED The number of vehicles potentially affected is approximately 308,000. 1/21
2 DEALER RESPONSIBILITY It is the Nissan dealer s responsibility to check Service Comm for the campaign status on each vehicle falling within the range of this Voluntary Service Campaign (PB135) that enters the service department. This includes vehicles purchased from private parties or presented by transient (tourist) owners and vehicles in a Nissan dealer s inventory. SPECIAL CUSTOMER ASSISTANCE FEATURES On some vehicles affected by this campaign, the headlamps may have already been repaired or replaced. If the customer paid to have their headlamps repaired or replaced, the customer may be eligible for reimbursement of the related expense. Please inform the customer that they can request reimbursement by contacting Nissan Consumer Affairs at If the headlamp was repaired or replaced at your dealership (customer pay), please provide a copy of the related repair order/invoice, if available, to the customer. If the repair or replacement was completed at a location other than your dealership, please inform the customer that they will need to provide proof of the repair and proof of payment when they contact Nissan Consumer Affairs. 2/21 NTB05-057b
3 SERVICE PROCEDURE Preparation 1. Make sure the headlamp switch is turned OFF. 2. Write down the radio station presets for later reprogramming. 3. Disconnect the negative battery cable. Diagnostic Flow Chart Perform steps in the flow chart for each headlamp (left and right side). START Check for Installation of Terminal Plate Kit Left side (driver side) page 4 Right side (passenger side) page 7 NO: Kit is not installed Inspect Reflector Housing (page 10) Yes: Already has kit installed Damaged: Reflector Housing is NG No Damage: Reflector Housing is OK Final Steps (Below) Perform Flow Chart for both headlamps (left and right) Replace headlamp assembly (page 15) Install Halogen Terminal Plate Kit (page 12) IMPORTANT: If the headlamp assembly does not have the damage referred to on Page 10, section Inspect Reflector Housings (left or right side), headlamp assembly replacement will not be covered under this campaign. Final Steps 1. Reconnect the negative battery cable. 2. Check the headlamps for correct operation. 3. Reprogram the radio station presets. 3/21 NTB05-057b
4 Check to see if the left side (driver side) headlamp has a Halogen Terminal Plate Kit installed. 1. Remove the securing clips for the air intake tube shown in Figure 2. Air Intake Tube Clips Figure 2 TP Air Intake Tube 2. Remove the air intake tube. Figure 3 TP Disconnect the harness mounting clip shown in Figure 4. Harness Mounting Clip Air Flow Meter Figure 4 TP /21 NTB05-057b
5 4. Unclip the upper half of the air filter box. Lift it off and secure it out of the way. Bungee Cord Upper Half of Air Filter Box Lower Half of Air Filter Box 5. Remove the securing bolt for the lower half of the air filter box. Bolt Figure 5 TP Upper Half of Air Filter Box 6. Remove the lower half of the air filter box. Lower Half of Air Filter Box Figure 6 TP Look behind the headlamp and open the back cover. Turn the cover about 45 degrees counterclockwise. Headlamp Back Cover (Turn Counterclockwise to Remove) Figure 7 TP /21 NTB05-057b
6 STANLEY Look at the location of the black (-) lead. Needs Terminal Plate Kit If the black lead is connected below the red lead as shown in Figure 8, the Terminal Plate Kit has not been installed. Go to Inspect Reflector Housing on page 10. Red (+) lead attached to the headlamp bulb Black (-) lead attached to original location Figure 8 TP Does Not Need Terminal Plate Kit If the black lead is connected above and a little to the side of the red lead as shown in Figure 9, a Terminal Plate Kit has already been installed on that headlamp. Reinstall all parts removed, then proceed to Check to see if the right side (passenger side) headlamp has a Halogen Terminal Plate Kit installed, starting on page 7. Black (-) lead attached to new location. Red (+) lead attached to original location. Figure 9 TP030224b. Turn cover clockwise to install Lettering is up (towards the top) when cover is installed correctly Figure 10 TP030220a 6/21 NTB05-057b
7 Check to see if the right side (passenger side) headlamp has a Halogen Terminal Plate Kit installed. 1. Remove the securing bolts for the coolant reservoir bottle (see Figure 11). Coolant Reservoir Bottle Figure 11 Bolts TP Coolant Reservoir Bottle 2. Lift out the reservoir bottle and set it aside. Figure 12 TP Remove the securing bolt for the reservoir bottle support bracket (see Figure 13). Bolt Support Bracket Figure 13 TP /21 NTB05-057b
8 Support Bracket 4. Remove the support bracket and set it aside. Figure 14 TP Look behind the headlamp and open the back cover. Turn the cover about 45 degrees counterclockwise. Headlamp Back Cover (Turn Counterclockwise to Remove) Figure 15 TP /21 NTB05-057b
9 STANLEY Look at the location of the black (-) lead. Needs Terminal Plate Kit If the black lead is connected below the red lead as shown in Figure 16, the Terminal Plate Kit has not been installed. Go to Inspect Reflector housing on page 10. Red (+) lead attached to the headlamp bulb Black (-) lead attached to original location Figure 16 TP Does Not Need Terminal Plate Kit If the black lead is connected above and a little to the side of the red lead as shown in Figure 17, a Terminal Plate Kit has already been installed on that headlamp. Reinstall all parts removed. Black (-) lead attached to new location. Red (+) lead attached to original location. Figure 17 TP030224b. Turn cover clockwise to install Lettering is up (towards the top) when cover is installed correctly Figure 18 TP030220a 9/21 NTB05-057b
10 Inspect Reflector Housings (left or right side) 1. Inspect the lens and reflector. You can inspect the reflector surface through the headlight lens (see Figure 19). If there is significant discoloration or hazing of either the reflector or the inside surface of the lens, go to Replace Headlamp Assembly (left or right side) on page 15.* Possible damaged area Hazing / Discoloration Reflector surface (behind the lens) * If the headlamp assembly is replaced, the repair is complete for that side of the vehicle. If there is no significant discoloration or hazing, go to step 2. Headlight lens Figure 19 TP Disconnect the Red (+), and the Black ( ) terminals (see Figure 20). Low beam bulb Bulb retaining spring 3. Unhook the low beam bulb retaining spring (see Figure 20). 4. Remove the low beam bulb and set it aside. Red (+) terminal CAUTION: Do Not touch the glass surface of the halogen bulb. Touching the bulb s glass surface may shorten its life. Black (-) terminal Figure 20 TP /21 NTB05-057b
11 5. Look at (inspect) the back of the reflector housing where the bulb mounts. It should look like the example shown in Figure 21a (no damage or evidence of corrosion or melting). NOTE: Examples of light to heavy damage are shown in Figure 21b below. If the reflector housing looks like the example in Figure 21a, go to Install Halogen Terminal Plate Kit on page 12. Figure 21a If the reflector housing has any amount of damage (see examples in Figure 21b), go to Replace Headlamp Assembly (left or right side) on page 15. Light Damage Heavy Damage Figure 21b 11/21 NTB05-057b
12 Install Halogen Terminal Plate Kit (left or right side) 1. Loosen the retaining spring screw (see Figure 22) enough to remove the retaining spring about one turn. Retaining spring screw. CAUTION: Do not remove the retaining spring screw. Loosen it just enough to remove and install the spring. 2. Remove and discard the old retaining spring. Figure 22 TP030222a 3. Install the new retaining spring from the service kit (see Parts Information). CORRECT INCORRECT Make sure the new spring is positioned properly under the retaining spring screw and then tighten the screw (see Figure 23). Edge CAUTION: Do not over tighten the screw. The plastic threads may be damaged. Spring should not rest on edge of surface Figure 23 TP /21 NTB05-057b
13 4. Re-install the low beam headlamp bulb: Make sure the bulb is seated properly (see Figure 24). CAUTION: Do Not touch the glass surface of the halogen bulb. Touching the bulb s glass surface may shorten its life. 5. Install the ground plate over the low beam bulb (see Figure 24). It s a new part from the service kit (see Parts Information). Make sure it is positioned correctly. Reflector / Bulb Housing Retaining Spring Terminal 6. Secure the bulb and ground plate in place with the bulb retaining spring. Low beam bulb Ground plate (new part) Figure 24 TP Bend the original ground terminal as shown in Figure 25 so it cannot be used. 8. Attach the Black ( ) terminal to the new location on the ground plate (see Figure 25). 9. Attach the Red (+) terminal to its original location (see Figure 25). Black (-) lead attached to new location. Negative (-) Terminal new location Retaining Spring Screw Retaining Spring Red (+) lead attached to original location. Ground plate Positive (+) Terminal Bend original ground (-) terminal. Figure 25 Original ground / negative (-) terminal Spring Hook TP030224a 13/21 NTB05-057b
14 Turn cover clockwise to install. 10. Reinstall the back cover on the headlamp assembly (see Figure 26). STANLEY 4340 Lettering is up (towards the top) when cover is installed correctly. Figure 26 TP030220a 11. Reinstall all parts removed to access the headlamp bulb in reverse order. 14/21 NTB05-057b
15 Replace Headlamp Assembly (left or right side) 1. Remove the six fascia and grill clips shown in Figure 27. Clips Clips Figure 27 TP Remove the five front clips on the engine splash shield shown in Figure 28. Clips Figure 28 TP Remove both front wheels. 15/21 NTB05-057b
16 NOTE: Steps 4 through 8 are illustrated only for the left side of the vehicle. Make sure to perform these steps for both sides (left and right). 4. Remove the inner fender (fender skirt) screws shown in Figure 29 (2 on each side). Screws Figure 29 TP Remove the fender skirt clips shown in Figure 30 (4 on each side). Clips Figure 30 TP Pull the fender skirt out of the way. Hook it behind the brake rotor. Inner Fender (Fender Skirt) Figure 31 TP /21 NTB05-057b
17 7. Look up into the area behind the bumper. Locate and remove the bumper fascia bolts shown in Figure 32 (two on each side). Bolts Figure 32 TP Hold the bumper fascia as shown in Figure 33 and carefully pull it loose from the corner support clip. Do this for both the left and right side corners. NOTE: The corner support clip is behind the fascia at about the center of the headlamp (see Figure 33). Figure 33 Fascial Support Clip Clip (Behind (behind Fascia) fascia) TP /21 NTB05-057b
18 9. Carefully lift off the bumper fascia (don t scratch it) and place in out of the way. NOTE: If the vehicle is equipped with fog lamps, disconnect them as you re carefully lifting off the fascia. Foam Support Figure 34 TP Replace the damaged headlamp. The headlamp is held on with 4 bolts shown in Figure 35. You ll need to disconnect three harness connectors from the old headlamp and reconnect them to the new headlamp. Bolts Bolts Figure 35 TP Reinstall the bumper fascia in reverse order. Make sure the foam support is in place while installing the fascia (see Figure 34 above). 18/21 NTB05-057b
19 12. Check headlamp adjustment as shown in Figure 36. Make sure all tires are inflated to correct pressure. Make sure there is no load in the vehicle other then the driver (or equivalent weight in the driver s seat), coolant and engine oil are filled to the correct level, and the fuel tank is full. Place vehicle on a flat surface. Basic illuminating area for adjustment should be within the range shown on the aiming chart. Figure If adjustment is needed, first loosen the adjusting screw all the way and then make adjustment by tightening the screw. Figure 37 19/21 NTB05-057b
20 PARTS INFORMATION DESCRIPTION PART # QUANTITY Kit-Halogen Terminal Plate J020 Halogen Low Beam Bulb Headlamp Assy, RH Z626 As needed Headlamp Assy, LH Z626 CLAIMS INFORMATION Submit a Campaign ( CM ) line claim using the following claims coding information: Campaign I.D.: PB135 OR DESCRIPTION OP CODE FRT Inspection Only; Both Headlights (no kits installed no headlights replaced) PB hrs. DESCRIPTION OP CODE FRT Inspect Both Headlights and PB hrs. Install One Kit OR DESCRIPTION OP CODE FRT Inspect Both Headlights and PB hrs. Install Two Kits OR DESCRIPTION OP CODE FRT Inspect Both Headlights, Install One Kit and Replace One Headlight Assembly PB hrs. OR DESCRIPTION OP CODE FRT Inspect Both Headlights, and Replace Both Headlight Assemblies PB hrs. OR DESCRIPTION OP CODE FRT Inspect Both Headlights, and Replace One Headlight Assembly PB hrs. IMPORTANT: If the headlamp assembly does not have the damage referred to on Page 10, section Inspect Reflector Housings (left or right side), headlamp assembly replacement will not be covered under this campaign. 20/21 NTB05-057b
21 OWNER S LETTER Dear Nissan owner: Nissan is committed to providing the highest levels of product quality and customer satisfaction. On some model year 2002 and 2003 Nissan Altima vehicles, there is a possibility that a low beam Halogen headlamp bulb may fail to illuminate due to a poor ground contact. What Nissan Will Do To prevent this from occurring, Nissan is conducting a Service Campaign to inspect and then repair or replace the headlamp assemblies, as needed. This free service should take about three hours to complete, but your Nissan dealer may require your vehicle for a longer period of time based upon their work schedule. What You Should Do Contact your Nissan dealer at your earliest convenience and arrange an appointment to have your headlamp assemblies inspected and repaired or replaced, as necessary, free of charge. Please bring this notice with you when you keep your service appointment. If you have paid to have your headlamps repaired or replaced prior to this campaign, you may be eligible for reimbursement of the related expense. For additional information, please contact Nissan Consumer Affairs at (800) You will still need to contact your Nissan dealer and have the campaign repair completed in order to ensure your vehicle has the improved parts installed. Thank you for your cooperation. We are indeed sorry for any inconvenience this may cause you. Nissan Division Nissan North America, Inc. 21/21 NTB05-057b
VOLUNTARY SERVICE CAMPAIGN 2006 M35 / M45; RADIATOR FAN CONTROL MODULE
Reference: ITB08-036 August 7, 2008 Date: VOLUNTARY SERVICE CAMPAIGN 2006 M35 / M45; RADIATOR FAN CONTROL MODULE CAMPAIGN ID #: P8227 APPLIED VEHICLE: 2006 M35 / M45 (Y50) Refer to Infiniti Net to confirm
More informationVOLUNTARY SERVICE CAMPAIGN G35 SEDAN AND COUPE SEAT MOUNTED SIDE AIR BAG HARNESS CONNECTOR
Reference: ITB10-034b June 22, 2012 Date: VOLUNTARY SERVICE CAMPAIGN 2003 2004 G35 SEDAN AND COUPE SEAT MOUNTED SIDE AIR BAG HARNESS CONNECTOR This bulletin has been amended. Changes have been made throughout
More informationVOLUNTARY SAFETY RECALL CAMPAIGN ARMADA AND TITAN FRONTIER, PATHFINDER AND XTERRA ECM RELAY
`Reference: NTB10-137b December 22, 2010 Date: VOLUNTARY SAFETY RECALL CAMPAIGN 2004 2006 ARMADA AND TITAN 2005 2006 FRONTIER, PATHFINDER AND XTERRA ECM RELAY This bulletin has been amended. The SERVICE
More informationVOLUNTARY RECALL CAMPAIGN MURANO ALTERNATOR
2003 Nissan Murano 3.5L Eng SE VOLUNTARY RECALL CAMPAIGN 2003-05 MURANO ALTERNATOR SERVICE CAMPAIGN BULLETIN Reference Number(s): NTB05-059, Date of Issue: July 28, 2005 NISSAN: 2003-05 Murano CAMPAIGN
More informationVOLUNTARY RECALL CAMPAIGN FUEL PUMP SCREEN
Reference: NTB03-077a August 21, 2003 VOLUNTARY RECALL CAMPAIGN FUEL PUMP SCREEN Date: This bulletin amends NTB03-077. This version updates the Service Procedure. Please discard all paper copies of the
More informationVOLUNTARY RECALL CAMPAIGN SKYVIEW ROOF GLASS
Reference: NTB04-100a November 5, 2004 VOLUNTARY RECALL CAMPAIGN SKYVIEW ROOF GLASS Date: IMPORTANT: THIS BULLETIN HAS BEEN REVISED. Figure 10 (page 7) was revised to include a rubber seal on the glass.
More informationVOLUNTARY RECALL CAMPAIGN PASSENGER AIR BAG OCCUPANT CLASSIFICATION SYSTEM (OCS)
Reference: NTB08-095c December 4, 2008 Date: VOLUNTARY RECALL CAMPAIGN 2007 2009 PASSENGER AIR BAG OCCUPANT CLASSIFICATION SYSTEM (OCS) This bulletin has been amended. Instruction for the AC adapter has
More informationVOLUNTARY RECALL CAMPAIGN ELECTRONIC CONTROL MODULE (ECM) CASE HOLDER FOAM
Reference: NTB03-112 December 10, 2003 VOLUNTARY RECALL CAMPAIGN ELECTRONIC CONTROL MODULE (ECM) CASE HOLDER FOAM Date: CAMPAIGN I.D. # / NHTSA #: P3163 / 03V-477 APPLIED VEHICLES: 2000-2003 Sentra (B15)
More informationVOLUNTARY RECALL CAMPAIGN PASSENGER AIR BAG OCCUPANT CLASSIFICATION SYSTEM (OCS)
Reference: ITB08-045d December 4, 2008 Date: VOLUNTARY RECALL CAMPAIGN 2007 2008 PASSENGER AIR BAG OCCUPANT CLASSIFICATION SYSTEM (OCS) This bulletin has been amended. Instruction for the AC adapter has
More informationVOLUNTARY RECALL CAMPAIGN FUEL HOSES
Reference: ITB06-006b April 4, 2006 Date: VOLUNTARY RECALL CAMPAIGN FUEL HOSES This bulletin has been amended. The Re-Assembly procedure for FX and G35 has been expanded. Please discard all previous versions
More informationVOLUNTARY SAFETY RECALL CAMPAIGN 2006 AND 2008 FRONTIER, XTERRA, PATHFINDER FUEL GAUGE INACCURACY
Reference: NTB10-031 March 18, 2010 Date: VOLUNTARY SAFETY RECALL CAMPAIGN 2006 AND 2008 FRONTIER, XTERRA, PATHFINDER FUEL GAUGE INACCURACY CAMPAIGN ID #: PC042 NHTSA #: 10V-075 APPLIED VEHICLES: 2006
More information2004 NISSAN TITAN; UPPER INTERIOR OCCUPANT PROTECTION VOLUNTARY SAFETY RECALL CAMPAIGN
Reference: NTB04-086 September 22, 2004 Date: 2004 NISSAN TITAN; UPPER INTERIOR OCCUPANT PROTECTION VOLUNTARY SAFETY RECALL CAMPAIGN CAMPAIGN I.D. # / NHTSA #: R0406 / 04V-345 APPLIED VEHICLE: 2004 Titan
More informationVOLUNTARY SAFETY RECALL CAMPAIGN QUEST FUEL PUMP CONTROL MODULE
Reference: NTB12-022a April 12, 2012 Date: VOLUNTARY SAFETY RECALL CAMPAIGN 2011-2012 QUEST FUEL PUMP CONTROL MODULE This bulletin has been amended. The NHTSA # and OWNER S LETTER have been added. Please
More informationZ; BOSE AUDIO AMPLIFIER CUSTOMER SATISFACTION INITIATIVE
Classification: Reference: Date: EL03-026 NTB03-086 October 1, 2003 2003 350Z; BOSE AUDIO AMPLIFIER CUSTOMER SATISFACTION INITIATIVE IMPORTANT This bulletin supercedes bulletin NTB02-111a Refer to this
More informationVOLUNTARY SAFETY RECALL CAMPAIGN 2014 LEAF ; REPLACEMENT OF THE TRACTION MOTOR INVERTER
Reference: NTB14-046 May 22, 2014 Date: VOLUNTARY SAFETY RECALL CAMPAIGN 2014 LEAF ; REPLACEMENT OF THE TRACTION MOTOR INVERTER CAMPAIGN I.D. #: PC281 APPLIED VEHICLE: 2014 LEAF (ZE0) Check Service Comm
More informationService Bulletin Product Update: Moisture in Headlight. March 10, WARRANTY CLAIM INFORMATION In warranty: The normal warranty applies.
Service Bulletin 07-016 Applies To: 2004 05 TSX ALL March 10, 2007 Product Update: Moisture in Headlight BACKGROUND The hood contacts the headlight lens and, over time, may create a small gap for water
More informationMAXIMA DRIVER'S POWER SEAT WILL NOT MOVE FORWARD OR BACKWARD
Classification: Reference: Date: EL01-030d NTB02-001d December 21, 2004 2000-2003 MAXIMA DRIVER'S POWER SEAT WILL NOT MOVE FORWARD OR BACKWARD This bulletin amends NTB02-001. The Applied Vehicles have
More informationService Bulletin
Service Bulletin 10-082 Applies To: 2007 08 Fit ALL March 11, 2011 Safety Recall: 2007 08 Fit Low Beam Headlights May Not Work (Supersedes 10-082, dated January 28, 2011, to revise the information marked
More informationALTIMA SEDAN; SLIGHT DRIVER'S POWER SEAT MOVEMENT SIDE-TO-SIDE
Classification: Reference: Date: BT08-025b NTB08-089b November 12, 2009 2007-2010 ALTIMA SEDAN; SLIGHT DRIVER'S POWER SEAT MOVEMENT SIDE-TO-SIDE The ACTION statement, Applied Vehicles/VINs/Dates/, Parts
More informationSERVICE BULLETIN FIREBOLT HEADLIGHTS PRODUCT PROGRAM 0501 Reason For Revision. Purpose. Kit Ordering Information. Motorcycles Affected
SERVICE BULLETIN B-076A July 10, 2008 2003-2006 FIREBOLT HEADLIGHTS PRODUCT PROGRAM 0501 Reason For Revision This revised bulletin includes corrected part information in the credit procedure tables, and
More information1 of 15 7/1/2015 10:02 AM 1Search FOG LIGHTS 2008 Nissan Xterra 4.0L Eng Off Road FRONT FOG LAMP [ FUNCTION DIAGNOSIS ] System Diagram Fig 1: Front Fog Lamp System Diagram System Description The front
More informationCustomerServicesDivision Toyota Motor Sales, U.S.A., Inc South Western Avenue P.O. Box 2991 Torrance, CA
CustomerServicesDivision Toyota Motor Sales, U.S.A., Inc. 19001 South Western Avenue P.O. Box 2991 Torrance, CA 90509 2991 TO: ALL TOYOTA DEALER PRINCIPALS, SERVICE MANAGERS, PARTS MANAGERS SUBJECT: SPECIAL
More informationQX4; DRIVER'S SEAT (WITH ADP ONLY) WON'T MOVE FORWARD OR BACKWARD
Classification: Reference: Date BT00-030a ITB00-065a December 21, 2004 2001 2003 QX4; DRIVER'S SEAT (WITH ADP ONLY) WON'T MOVE FORWARD OR BACKWARD This bulletin amends ITB00-065. This version amends the
More informationMAXIMA DRIVER'S POWER SEAT WILL NOT MOVE FORWARD OR BACKWARD TECHNICAL SERVICE BULLETIN
Page 1 of 11 2000-2003 MAXIMA DRIVER'S POWER SEAT WILL NOT MOVE FORWARD OR BACKWARD TECHNICAL SERVICE BULLETIN Reference Number(s): NTB02-001d, Date of Issue: December 21, 2004 NISSAN: 2000-2003 Maxima
More informationService Bulletin. Safety Recall: Fit Low Beam Headlights May Not Work
Service Bulletin 10-082 Applies To: 2007 08 Fit ALL January 28, 2011 Safety Recall: 2007 08 Fit Low Beam Headlights May Not Work (Supersedes 10-082, dated January 7, 2011, to revise the information marked
More informationService Bulletin. Safety Recall: TL Power Steering Feed Hose Leak (Supersedes , dated June 27, 2012; see REVISION SUMMARY)
Service Bulletin Applies To: 2007 08 TL Check the in VIN status for eligibility 12-020 August 10, 2012 Safety Recall: 2007 08 TL Power Steering Feed Hose Leak (Supersedes 12-020, dated June 27, 2012; see
More informationRetailer Technical Journal Headlamp low beam connector replacement
Retailer Technical Journal 19254 Headlamp low beam connector replacement Date 7-6-2009 Volvo Cars of North America, LLC Technical Support Reference: VIDA, Retailer Technical Journal 19636 Note! If using
More informationNISSAN BULLETIN 2015 Murano ABS Actuator Voluntary Safety Recall Campaign
NISSAN BULLETIN 2015 Murano ABS Actuator Voluntary Safety Recall Campaign Attention: Dealer Principal, Sales, Service & Parts Managers Reference: PC375 Date: June 5, 2015 A STOP SALE CONDITION IS IN EFFECT.
More informationALTIMA SEDAN, COUPE, AND HYBRID; ENGINE NO CRANK / NO START
Classification: Reference: Date: EL10-030 NTB10-139 November 23, 2010 ALTIMA SEDAN, COUPE, AND HYBRID; ENGINE NO CRANK / NO START APPLIED VEHICLES: 2007 2010 Altima Sedan (L32) with CVT only 2008 2010
More informationService Bulletin
Service Bulletin 12-057 Applies To: 2007 11 Element ALL September 19, 2012 Safety Recall: Accessory Trailer Hitch Wire Harness Is Mis-Wired (Supersedes 12-057, dated August 31, 2012, to revise the information
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS 1. 2. 3. 4. DESCRIPTION: APPLICATION: PART NUMBER: KIT CONTENTS: Fog Lamp Kit Versa Note (SV Only) 999L1 4Z000 - Fog Lamp Kit Item QTY Description Service Part Number
More informationEmissions Recall Circular
IMPORTANT INFORMATION Please inform and provide a copy of this document to every person in your dealership with campaign-related responsibilities, including Service, Parts and Accounting personnel. By
More informationTOYOTA HIGHLANDER FOG LIGHTS Preparation Part Number: PT , BLACK Part Number: PT , ALUMINIZED
Preparation Part Number: PT413-42191, BLACK Part Number: PT413-42190, ALUMINIZED Kit Contents Item # Quantity Reqd. Description 1 1 RH Fog Light 2 1 LH Fog Light Hardware Bag Contents Item # Quantity Reqd.
More informationSENTRA; LONG ENGINE CRANK TIME BEFORE START
Classification: Reference: Date: EC05-001a NTB05-052a September 8, 2006 2002 2006 SENTRA; LONG ENGINE CRANK TIME BEFORE START APPLIED VEHICLES: 2002 Sentra (B15) with QR25 engine only. 2003 2006 Sentra
More informationLANCER FOG LAMP KIT MZ380479EX (for RHD) INSTALLATION AND HANDLING INSTRUCTIONS
LANCER FOG LAMP KIT MZ380479EX (for RHD) INSTALLATION AND HANDLING INSTRUCTIONS Fog lamp Thank you for purchasing the Mitsubishi Genuine Accessory. To install and use the product correctly with proper
More informationTECHNICAL INSTRUCTIONS FOR SPECIAL SERVICE CAMPAIGN 40F
TECHNICAL INSTRUCTIONS FOR SPECIAL SERVICE CAMPAIGN 40F 2002 THROUGH EARLY 2004 MODEL YEAR NORTH AMERICAN PRODUCED (NAP) TOYOTA CAMRY CURTAIN SIDE AIRBAG Page 1 of 26 I. OPERATION FLOW CHART Verify Vehicle
More informationSENTRA; HEATER CASE DOORS BECOME STUCK
Classification: Reference: Date HA02-008a NTB03-005a February 26, 2003 2002-2003 SENTRA; HEATER CASE DOORS BECOME STUCK The Service Procedure section of this bulletin has been amended to include additional
More informationSCION tc FOG LIGHT (Halogen or LED)
Part Number: STC-314 / STC-814 Kit Contents Item # Quantity Reqd. Description 1 2 Fog Lamps 2 2 Fog Light bezels 3 1 Switch Assembly 4 1 Fog Light Operation guide 5 1 Harness Bag Hardware Bag Contents
More informationSERVICE PROGRAM BULLETIN
ATTENTION: GENERAL MANAGER PARTS MANAGER CLAIMS PERSONNEL SERVICE MANAGER IMPORTANT - All Service Personnel Should Read and Initial SERVICE PROGRAM BULLETIN APPLICABILITY: SUBJECT: 2000MY Subaru Legacy
More informationShelby GT500 Front Fascia Conversion Kit (05-09 All) Item # Installation Time: 1 Day. Required tools:
Shelby GT500 Front Fascia Conversion Kit (05-09 All) Item #53611 Installation Time: 1 Day Required tools: Phillips Screw driver 10mm Socket + Ratchet/Wrench 8mm Socket + Ratchet/Wrench 5mm Socket + Ratchet/Wrench
More informationProduct Campaign Bulletin
Nissan Ireland Cedar House Park West Business Park Nangor Road, Dublin 12 Product Campaign Bulletin REFERENCE: MODEL: PCB-NES-12-052 J10 & J10+2 Qashqai SUBJECT: PCB J10 - PG2B9 and PS2B7- Steering wheel
More informationSPECIAL SERVICE CAMPAIGN (SSC) 10F ( MY ECHO AND AVALON TETHER ANCHOR UPGRADE)
TO: SUBJECT: ALL TOYOTA DEALER PRINCIPALS, SERVICE MANAGERS, PARTS MANAGERS SPECIAL SERVICE CAMPAIGN (SSC) 10F (2000-2001 MY ECHO AND AVALON TETHER ANCHOR UPGRADE) Toyota will initiate a Special Service
More informationJuly Models. Subject
Dealer Service Instructions for: July 2001 Safety Recall No. 970 Models 1994-1996 (BR) Dodge Ram Pickup Trucks NOTE: This recall applies only to the above vehicles equipped with a 5.9L Cummins turbo diesel
More informationMazda North American Operations Irvine, CA
Service Bulletin Mazda North American Operations Irvine, CA 92618-2922 Subject: MIL ON - P2070 SET Bulletin No: 01-019/08 2004-2007 RX-8 - MIL ON - P2070 SET BULLETIN NOTE This bulletin supersedes the
More informationCOMPONENTS ILLUSTRATION
COMPONENTS ILLUSTRATION ILLUSTRATION ILLUSTRATION ILLUSTRATION ILLUSTRATION REMOVAL 1. REMOVE REAR NO. 2 FLOOR BOARD (for Separate Type) 2. REMOVE REAR DECK FLOOR BOX 3. REMOVE REAR NO. 3 FLOOR BOARD
More informationALLDATA Online Lexus Truck RX 330 FWD V6-3.3L (3MZ-FE) - Headlight As... Page 1 of 10. Headlight Assembly. LH Headlamp Assy Part 1
ALLDATA Online - 2005 Lexus Truck RX 330 FWD V6-3.3L (3MZ-FE) - Headlight As... Page 1 of 10 Home Account Contact ALLDATA Log Out Help PAUL REDEHOFT Select Vehicle New TSBs Technician's Reference Component
More informationRecall - Parking Brake Lever Assembly
1991 Buick Park Avenue V6-231 3.8L VIN L SFI Copyright 2013, ALLDATA 10.52 Page 1 Technical Service Bulletin # 92C25 Date: 911001 Recall - Parking Brake Lever Assembly Model Year: 1992 Bulletin No.: 92-C-2
More informationFILE: SERVICE: GROUP 00 OF SERVICE INFORMATION BINDER PARTS: GROUP I OF INFORMATION _ PARTS & ACCESSORIES BINDER
FILE: SERVICE: GROUP 00 OF SERVICE INFORMATION BINDER PARTS: GROUP I OF INFORMATION _ PARTS & ACCESSORIES BINDER Campaign No. 2006080004, November 2006 Revision History Revision Date Purpose A 11/03/06
More information2003 (LH) Dodge Intrepid, Chrysler Concorde and 300M (PT) Chrysler PT Cruiser (PL) Dodge Neon (JR) Dodge Stratus Sedan
Dealer Service Instructions for: Customer Satisfaction Notification No. C08 March 2003 Effective immediately, all repairs on involved vehicles are to be performed according to this notification. Rapid
More informationGENUINE FOG LAMP KIT
GENUINE FOG LAMP KIT Using (Installation) Instructions Applicable model:mazda CX-5 Part number:kd33 V4 600 Thank you very much for buying the Mazda Genuine Parts. Before removal and installation, you are
More informationCampaign No , September 2006
Campaign No. 2006080004, September 2006 Effective Serial Number Range Models Chassis End Number From To Every vehicle in the VIN range may not be included in the campaign. VMI must always be checked before
More informationService Bulletin
Service Bulletin 08-043 Applies To: 2003 Accord 4-door ALL October 15, 2008 Safety Recall: Windshield Wiper Motor Does Not Work (Supersedes 08-043, dated July 17, 2008, to update the information marked
More informationCertain Model Year Tacoma 2TR-FE Vehicles Exhaust Pipe Replacement for Catalytic Converter
To: Subject: All Toyota Dealer Principals, Service Managers, and Parts Managers Special Service Campaign (SSC) F0U Certain 2010-2014 Model Year Tacoma 2TR-FE Vehicles Exhaust Pipe Replacement for Catalytic
More informationVOLUNTARY SERVICE CAMPAIGN FRONT SEAT BELT BUCKLES
Reference: 95V-103.002 September 22, 1995 Date: VOLUNTARY SERVICE CAMPAIGN FRONT SEAT BELT BUCKLES This amended version of NTB95-085 updates information in the Front Seat Belt Buckles. Please discard all
More informationItem C& D Not Applicable C
GENUINE PARTS INSTALLATION INSTRUCTIONS DESCRIPTION: APPLICATION: PART NUMBER(S) REQUIRED FOR INSTALLATION: KIT CONTENTS: LED Fog Lamp Upgrade Rogue Sport 999F1 V4001 A B Item C& D Not Applicable C D Do
More information#14062A: Product Safety - Brake Booster Pump - Cavity Plug - (Apr 4, 2014)
1 of 12 6/18/2014 9:30 AM Document ID: 3802123 #14062A: Product Safety - Brake Booster Pump - Cavity Plug - (Apr 4, 2014) Subject: 14062A Brake Booster Pump Cavity Plug Models: 2013 and some 2014 Cadillac
More informationService Bulletin
Service Bulletin 17-090 November 10, 2017 07659 Version 1 Product Update: 2018 Odyssey Rear Power Window Switches AFFECTED VEHICLES Year Model Trim VIN Range 2018 Odyssey ALL except LX Check the in VIN
More informationService Bulletin 1988 PRELUDE. RECALL: 1988 Prelude Power Steering Supply Hose
Service Bulletin Model Applicable To File Under Bulletin No. 1988 PRELUDE See VEHICLES AFFECTED ENGINE 88-014 Issue Date APRIL 20, 1988 RECALL: 1988 Prelude Power Steering Supply Hose PROBLEM When subjected
More informationProduct Update Circular
IMPORTANT INFORMATION Please inform and provide a copy of this document to every person in your dealership with campaign-related responsibilities, including Service, Parts and Accounting personnel. By
More information2007 MAXIMA; MIL 'ON' W/DTC P0840 OR P0845
Classification: Reference: Date: AT08-001 NTB08-042 April 3, 2008 2007 MAXIMA; MIL 'ON' W/DTC P0840 OR P0845 APPLIED VEHICLE: 2007 Maxima (A34) IF YOU CONFIRM The MIL is ON with one of the following DTC
More informationMAXIMA A/T SHIFT CONTROL DEVICE - HARD TO SHIFT
Classification: Reference: Date: AT99-001a NTB99-014a June 19, 2000 1998-1999 MAXIMA A/T SHIFT CONTROL DEVICE - HARD TO SHIFT This bulletin amends NTB99-014 and includes updated Service and Warranty Information.
More information2002 ALTIMA; MANUAL A/C TEMPERATURE NOT ADJUSTABLE
Classification: Reference: Date: HA02-003 NTB02-048 June 12, 2002 2002 ALTIMA; MANUAL A/C TEMPERATURE NOT ADJUSTABLE APPLIED VEHICLE: APPLIED VIN: 2002 Altima (L31) with Manual A/C ONLY All vehicles built
More informationSAFETY RECALL. CERTAIN YZF-R3F/G MODELS FACTORY MODIFICATION CAMPAIGN Clutch Pressure Plate and Oil Pump
MOTORCYCLE 7/6/2016 M2016-005R 2016 YAMAHA MOTOR CORPORATION, U.S.A. SAFETY RECALL This modification has top priority. This bulletin must be performed immediately to ensure customer safety. NOTE: Bulletins
More informationSCION tc FOG LIGHT. Part Number: STC-312 / STC-812
SCION tc 2011-2013 FOG LIGHT Part Number: STC-312 / STC-812 Kit Contents Item # Quantity Reqd. Description 1 2 Fog Lamps 2 2 Fog Light bezels 3 1 Switch Assembly 4 1 Fog Light Operation guide 5 1 Harness
More informationService Bulletin American Honda Motor Co., Inc.
Service Bulletin American Honda Motor Co., Inc. 2008-2009 CRF450X Decompressor Shaft Pin PRODUCT UPDATE CAMPAIGN Campaign end date: June 30, 2015 American Honda s Motorcycle Division is conducting a Product
More informationPart Number: STC-314. Special Chemicals 3M Silicon Sealant
Date: 08.11.2014 SCION tc 2014-15 FOG LIGHT (Halogen or LED) Part Number: STC-314 Kit Contents Item # Quantity Reqd. Description 1 2 Fog Lamps 2 2 Fog Light bezels 3 1 Switch Assembly 4 1 Fog Light Operation
More informationROGUE AND ROGUE SELECT; REDUCED PERFORMANCE DUE TO CVT FLUID TEMPERATURE PROTECTION LOGIC
Classification: Reference: Date: AT16-013 NTB16-090 September 9, 2016 2011-2015 ROGUE AND ROGUE SELECT; REDUCED PERFORMANCE DUE TO CVT FLUID TEMPERATURE PROTECTION LOGIC APPLIED VEHICLES: 2011-2013 Rogue
More informationECM REPLACEMENT PROCEDURES
Classification: Reference: Date: EC00-007c NTB00-052c April 16, 2004 ECM REPLACEMENT PROCEDURES ATTENTION: THIS BULLETIN HAS BEEN REVISED. The Service Procedures for replacing an ECM on an Applied vehicle
More information#88-C-19: CAMPAIGN SEAT BELT BUCKLES - (Nov 1, 1988)
#88-C-19: CAMPAIGN SEAT BELT BUCKLES - (Nov 1, 1988) MODELS AFFECTED 1988 PONTIAC LEMANS TO: ALL PONTIAC DEALERS The National Traffic and Motor Vehicle Safety Act, as amended, provides that each vehicle
More informationFILE: SERVICE: GROUP 00 OF SERVICE INFORMATION BINDER PARTS: GROUP I OF INFORMATION PARTS & ACCESSORIES BINDER
FILE: SERVICE: GROUP 00 OF SERVICE INFORMATION BINDER PARTS: GROUP I OF INFORMATION PARTS & ACCESSORIES BINDER Campaign No. 2003040005, October 2008 Revision History Revision Date Purpose d 10/31/08 Relaunched
More informationSafety Recall Circular
IMPORTANT INFORMATION Please inform and provide a copy of this document to every person in your dealership with campaign-related responsibilities, including Service, Parts and Accounting personnel. By
More informationHeadlight Assembly. Headlight Assembly
Headlight Assembly Headlight Assembly Headlight Assembly HEADLIGHT ASSEMBLY REMOVAL Use the same procedures for the RH and LH sides. The procedures listed below are for the LH side. 1. DISCONNECT CABLE
More information#06083: Product Safety - Crankshaft Position Sensor Engine Stall - (Dec 11, 2007)
Page 1 of 6 2001 Chevrolet Chevy K Silverado - 4WD Sierra, Silverado, Suburban, Tahoe, Yukon (VIN C/K) Service Manual Campaigns Safety Document ID: 2044115 #06083: Product Safety - Crankshaft Position
More informationService Bulletin American Honda Motor Co., Inc.
Service Bulletin American Honda Motor Co., Inc. SAFETY RECALL 2001-2012 GL1800/A Secondary Master Cylinder Inspection/Replacement Honda Motor Co., Ltd. is conducting a Safety Recall to inspect and, if
More informationALTIMA; MIL ON P1273 (QR25 ENGINE) MAY BE CAUSED BY THE REAR O2 SENSOR
Classification: Reference: Date: EC05-016a NTB06-039a May 17, 2006 2004 2005 ALTIMA; MIL ON P1273 (QR25 ENGINE) MAY BE CAUSED BY THE REAR O2 SENSOR This bulletin has been amended. The Claims Information
More informationService Bulletin Safety Recall: Accord Power Steering Feed Hose Leak. January 26, 2013
Service Bulletin Applies To: 2003 07 Accord V6 Check the in VIN status for eligibility 13-012 January 26, 2013 Safety Recall: 2003 07 Accord Power Steering Feed Hose Leak BACKGROUND Prolonged high under-hood
More informationALTIMA; POOR HEATER PERFORMANCE
Classification: Reference: Date: HA02-002b NTB02-047b September 9, 2003 2002 2003 ALTIMA; POOR HEATER PERFORMANCE This bulletin amends NTB02-047a. This version updates the Service Procedure. Please discard
More informationCUSTOMER SATISFACTION PROGRAM
Program Bulletin Bulletin No.: Date: 30990 April 2016 SUBJECT: CUSTOMER SATISFACTION PROGRAM Oil Pickup Tube Bolt Retention MODELS: 2016 Cadillac CTS-V Equipped with 6.2L V-8 (RPO LT4) 2016 Chevrolet Camaro
More informationGENUINE FOG LIGHT INSTALLATION AND USER S INSTRUCTIONS
GENUINE FOG LIGHT INSTALLATION AND USER S INSTRUCTIONS Thank you for purchasing a genuine Mazda accessory. Before removal and installation, be sure to thoroughly read these instructions. Please read the
More informationGENUINE FOG LAMP KIT
GENUINE FOG LAMP KIT Using (Installation) Instructions Applicable model : MAZDA CX-7 Part Number : ER18 V4 600 (small tank) ER19 V4 600 (large tank) Thank you very much for buying the Mazda Genuine Parts.
More informationService Bulletin
Service Bulletin Applies To: 2004 TL ALL 2005 TL From VIN 19UUA6...5A000033 thru 19UUA6...5A058279 08-013 October 15, 2008 Safety Recall: Windshield Wiper Motor Does Not Work (Supersedes 08-013, dated
More informationPart Number: TRA-316/TRA-816
Date: 07.29.2016 TOYOTA RAV4 2016- FOG LIGHT (Halogen/LED) Part Number: TRA-316/TRA-816 Kit Contents Item # Quantity Reqd. Description 1 2 Light Housings 2 2 Light Bezels 3 1 Wire Harness Bag* 4 1 Connector
More informationSubject: Brake Light Pressure Switches. Models Affected: Specific Freightliner Cascadia and Western
Subject: Brake Light Pressure Switches Models Affected: Specific Freightliner Cascadia and Western Star 4700, 4900, 5700, 6900 model vehicles manufactured March 27, 2007, through November 21, 2017. General
More informationTOYOTA PRIUS FOG LIGHT (Halogen or LED)
Part Number: TPR-413 / TPR-813 Kit Contents Item # Quantity Reqd. Description 1 2 Fog Lamps 2 1 Lower Grill 3 1 Switch Assembly 4 1 Fog Light Operation guide 5 1 Harness Bag Hardware Bag Contents Item
More informationPATHFINDER, QUEST, MURANO, MAXIMA, ALTIMA V6 CVT JUDDER AND DTC P17F0 OR P17F1 STORED
Classification: Reference: Date: APPLIED VEHICLE: AT15-005b NTB15-015b September 10, 2015 PATHFINDER, QUEST, MURANO, MAXIMA, ALTIMA V6 CVT JUDDER AND DTC P17F0 OR P17F1 STORED This bulletin has been amended
More information#04017A: Special Policy - Tail Lamps/Stop Lamps - (Aug 6, 2004)
Page 1 of 9 2004 Chevrolet TrailBlazer - 4WD Bravada, Envoy, Rainier, TrailBlazer (VIN S/T) Service Manual Campaigns Special Policy #04017A: Special Policy - Tail Lamps/Stop Lamps - (Aug 6, 2004) Subject:
More information(WK) Jeep Grand Cherokee (WD) Dodge Durango
Dealer Service Instructions for: Safety Recall S16 Left Front Brake Caliper Revised May 2016 Models NOTE: The wheel lug nut torque specification has been updated. 2015-2016 (WK) Jeep Grand Cherokee (WD)
More information14371B Special Coverage Adjustment Engine Coolant Leak from the Water Pump
14371B Special Coverage Adjustment Engine Coolant Leak from the Water Pump 2011-2014 Chevrolet Cruze 2012-2014 Chevrolet Sonic With 1.4L Engine (RPO LUJ or LUV) The Warranty Transaction Information section
More informationFront Bumper Fascia Replacement
Page 1 of 10 2008 Pontiac G8 G8 Service Manual Body Repair Bumpers and Fascias Repair Instructions Document ID: 2044380 Front Bumper Fascia Replacement Removal Procedure Caution: Refer to Safety Glasses
More informationSAFETY RECALL GL1800/A. Frame Weld Inspection
Service Bulletin American Honda Motor Co., Inc. SAFETY RECALL 2001-2002 GL1800/A Frame Weld Inspection American Honda is conducting a Safety Recall on affected 2001-2002 GL1800/A Gold Wings to inspect
More informationMustang GT Splitter Bracket Kit M-17A626-MB INSTALLATION INSTRUCTIONS
!!! PLEASE READ THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION!!! Caution: If you are not confident that you can complete the installation safely, have it completed by a certified technician!
More informationTOYOTA TACOMA FOG LIGHT (Halogen or LED)
Part Number: TTA-312 / TTA-812 Kit Contents Item # Quantity Reqd. Description 1 2 Fog Lamps 2 1 Switch Assembly 3 1 Fog light operation guide 4 1 Harness bag Hardware Bag Contents Item # Quantity Reqd.
More informationQUEST; WATER LEAK IN CARGO AREA
Classification: Reference: Date: BT05-018 NTB05-049 June 22, 2005 2004 2005 QUEST; WATER LEAK IN CARGO AREA APPLIED VEHICLES: 2004 2005 Quest (V42) IF YOU CONFIRM IF YOU CONFIRM Rear Cargo Area Water is
More informationDecember 2000 Dealer Service Instructions for:
December 2000 Dealer Service Instructions for: Safety Recall No. 964 -- Starter Terminal Block Models 2001 (PL) Dodge Neon R/T NOTE: This recall applies only to the above vehicles equipped with a 2.0L
More informationI30 MIL "ON" WITH DTC P0420 STORED - THREE WAY CATALYST FUNCTION
Classification: Reference: Date: EC00-025b ITB00-054b June 7, 2004 2000-2001 I30 MIL "ON" WITH DTC P0420 STORED - THREE WAY CATALYST FUNCTION IMPORTANT: THIS BULLETIN HAS BEEN REVISED. The Service Information
More informationLEXUS LC/LCh CARBON FIBER LOWER GRILLE Preparation
Preparation Part Number: PT478-11175-05 Kit Contents Item # Quantity Reqd. Description 1 1 Carbon Fiber Lower Grille Insert 2 3 Hardware Bag Contents Item # Quantity Reqd. Description 1 2 3 Additional
More informationQUEST; REVISED SLIDING DOOR INITIALIZATION PROCEDURE
Classification: Reference: Date: BT04-043 NTB04-125 October 26, 2004 2004-2005 QUEST; REVISED SLIDING DOOR INITIALIZATION PROCEDURE APPLIED VEHICLES: 2004 2005 Quest (V42) with power sliding doors. IF
More information#04039B: Special Coverage Adjustment - Injectors- Replace - (Nov 19, 2007)
Page 1 of 6 Document ID: 2038809 #04039B: Special Coverage Adjustment - Injectors- Replace - (Nov 19, 2007) Subject: 04039B - Special Policy Adjustment - Injector - Replace Models: 2001-2004 Chevrolet
More information10134C Special Coverage Adjustment Catalytic Converter Warranty Extension
10134C Special Coverage Adjustment Catalytic Converter Warranty Extension 2006-2007 Chevrolet Malibu Equipped with 2.2L Engine (L61) 2008 Chevrolet Malibu 2006-2008 Pontiac G6 2008 Saturn AURA Equipped
More informationZ ROADSTER; SOFT TOP ASSEMBLY REMOVAL AND INSTALLATION
Classification: Reference: Date: BT03-046a NTB03-116a January 29, 2004 2004 350Z ROADSTER; SOFT TOP ASSEMBLY REMOVAL AND INSTALLATION This bulletin amends NTB03-116. This version updates the Parts Information.
More information