ND DYNAMOC .STATIC STR INTS BERGEN-PATERSON PIPESUPPORT CORPORATION DESIGN INFORMATION WOBURN, MASSACHUSETTS 01888

Transcription

1 CATALOG 82 ENGINEERING SUPPLEMENT NO.3.STATIC ND DYNAMOC STR INTS DESIGN INFORMATION BERGEN-PATERSON PIPESUPPORT CORPORATION WOBURN, MASSACHUSETTS 01888

2 Bergen-Paterson markets the widest selection of restraint assemblies and devices which allows the designer to select devices technically and economically suited for the specific application, by type, size and configuration. Bergen-Paterson restraint systems now cover a broader range of load ratings and allow greater flexi- bility in field adjustment. High precision stainless steel ball bushings and pins are now standard components throughout the line. Also included is a new series of restraint yoke clamps. Bergen-Paterson hydraulic snubbers have also been improved and are available with options to better suit the different conditions the application requires. E Specifications : All Bergen - Paterson restraints are designed to meet requirements of: Manufacturers Standardization Society SP-58, Manufacturers Standardization Society SP-69 and ANSI Code for Pressure Piping ANSI B31.1. Rigid Strut Assemblies RECOMMENDED SERVICE : Used to restrain movement of piping in one direction. Movement due to thermal expansion in other directions should be evaluated. STANDARD DESIGN FEATURES: Designed to restrain tensile and/or compressive forces. Tight fitting connections allow positive control of piping systems. Hydraulic Snubber Assemblies GENERAL APPLICATION: Used for the control and protection of piping and equipment subject to shock (impulse) loading and swaying (cyclic) conditions. Its use transfers any imposed forces on the piping or equipment directly to the building structure at the instant of shock occurrence, while at all other times allowing free unrestricted movement through its normal operating range. SPECIFIC APPLICATIONS: Earthquake protection. To prevent damage by wind in outdoor installations. Employed at points in piping systems subject to shock loadings generated by quick closing valves, water hammer, relief valve reaction or other applied shock loads. STANDARD DESIGN FEATURES: Piping and/or equipment movement is controlled by tamper-proof dual stage flow control poppets designed with self cleaning orifices. Furnished as a complete, compact, and efficient unit, ready for immediate use. Manifold configuration requiring no external piping. Ethylene-propylene (EP) elastomer seals. Spherical, self-aligning ball bushings allow for ± 50 of angular motion or misalignment. Hydraulic fluid - General Electric SF1154 Methyl Phenyl Polysiloxane Silicone Fluid. Pressurized hydraulic reservoir allows mounting in any spatial orientation. Virtually no resistance to normal thermal movements of the piping. 7 Copyright 1982 Bergen-Paterson Pipesupport Corporation, Boston, Mass. 1 Units meeting the requirements of the ASME Boiler and Pressure Vessel Code, Section III are also available in accordance with Bergen-Paterson load capacity data sheets. Spherical, self-aligning ball bushing at both ends of the strut allow for ±5 of angular motion or misalignment. Can be installed in any spatial orientation. Field adjustment is available in all assemblies. All welding work required in the field is recommended to be fillet welds. Paint - Standard primer finish. Paint - standard primer finish. Large restraining forces compared to size. Functions in restraining tension and compression. Designed for continuous operation at 200 F with brief transients to a maximum of 350 F. Seals and fluid have been tested to a cumulative gamma dose of 3 x 107 rads without impairment of operation. Stroke determination is made from built-in datum point located on piston rod. Fluid Level Indicator - Provides concise determination of exact fluid level in the unit, thereby eliminating estimate of reserve fluid level. OPTIONAL DESIGN FEATURES: Stroke Position Indicator - A striped piston rod is available for "at-a-glance" determination of stroke position. Integral Relief Valve - A non-adjustable valve, which is factory preset at 133%, or 200% of rated load. Activation indicator - At 100 psig or greater, a pop-up device indicates that the unit is restraining load. Must be ordered with optional integral relief valve. Rigid Strut Application - When no thermal growth is anticipated after lock-up an optional poppet valve, without bleed, is furnished. Must be ordered with optional integral relief valve. More detailed information and brochures concerning the Bergen-Paterson Snubber are available upon request from your nearest Bergen-Paterson sales office. Dimensions subtect to change wlthoutnotlc.

3 Structural Attachment Part 1000 Sizes.7 through 4 Sizes 7 through 130 SIZE RANGE : 700 through 130,000 pounds load. MATERIAL : Carbon steel except load pin which is stainless steel. SERVICE: For attachment of struts to structures. MAX. TEMP.: 350 F for the rated loads shown. FEATURES : Can be used as a second end attachment. USED WITH : Bergen-Paterson parts 2015, 2250, 2252, 2525, ORDERING: Specify part number and size. NOTE: This product is designed to function with a 10 cone of action, and a 90 arc of loading. Loading beyond this cone or arc is not recommended. Inches Size n E G L N P R T W /2 1 1/2 3 1/2 Weight lbs. (APPROX.) 3 11/ /4 5 11/2 3/4 1/2 3/4 1/2 13/ /4 5 11/2 3/4 1/2 3/4 1/2 13/ /2 11/2 3/4 1 3/4 31/ /R /2 11/2 3/a 1 3/a 31/ /2 1 41/ /4 11/2 53/ /4 13/4 11/ /4 3 11/2 21/4 1 1/ / / /4 21/2 13/4 73/ / /2 31/4 13/4 87/ n Size designation indicates load rating in kips. Light Duty Rigid Rod Strut Part 2015 E R SIZE RANGE : 700 to 4,000 pounds load. MATERIAL: Carbon steel except load pin which is stainless steel. SERVICE: For rigid restraint applications where short pin to pin dimensions are required. INSTALLATION: Securely fasten end bracket to structure. Screw rod into paddles and adjust for the desired overall length. Fasten strut to pipe attachment (in place). After all minor adjustments are made the unit is locked by tightening the hex nut against the paddle. NOTE: Rods should be visible in paddle sight holes to insure proper thread engagement. FIELD ADJUSTMENT: Plus or minus 11/2 ". USED WITH: Bergen-Paterson parts 6175, 6202, 6222, 6252, 6520, 6521, 6525, ORDERING: Specify part number, size, strut length (pin to pin in inches) and customer mark number (if any). Restraint attachments must be ordered separately. 1 is Size n Inches Wgt. Torque O P to P Min. P to P ft.-ibs. A E P R S T Min. Max. (APPROX.) (NOMINAL).7 103/4 33 3/ /2 1/ /4 33 3/a 21/4 1/2 11/8 11/2 5/ /4 42 ' 1 21/4 1/2 11/4 13/4 5/ n Size designation indicates load rating in kips. -2-

4 Adjustable Rigid Strut Part 2250 SIZE RANGE: 700 to 130,000 pounds load. MATERIAL: Carbon steel except load pin which is stainless steel. SERVICE : For rigid restraint applications allowing the greatest amount of field adjustment-without field welding. INSTALLATION: Securely fasten end bracket to structure. Attach strut paddle to end bracket. Adjust strut for the desired overall length. Fasten strut to pipe attachment (in place). After all minor adjustments are made, the unit is locked by tightening the hex nuts against the extension piece. NOTE: Rods should be visible in the sight holes at each end of the strut to assure proper thread engagement. All struts are normally fabricated in four inch increments between minimum and maximum pin to pin. Special lengths or other increments available upon request. FIELD ADJUSTMENT : Plus or minus two inches (min. standard). USED WITH : Bergen-Paterson parts 6175, 6202, 6222, 6252, 6520, 6521, 6525, ORDERING: Specify part number, size, strut length (pin to pin in inches) and customer mark number (if any) Size n Inches Wgt. Torque a P to P Pipe Size E P R S T W Min. P to P ft.-lbs. (APPROX.) (NOMINAL) Min. Max. D /2 S/40 17/ /2 1/ /2 S/40 21/4 1/ /2 % S/80 21/4 1/2 11/4 13/4 % /2 S/80 27/. 3/4 2 21/2 7 1/ /2 S/80 27/8 3/4 2 21/2 7/8 1/ S/ / /2 S/80 41/4 11/ /2 11/2 1/ S/80 55/8 11/ / S/80 61/4 13/ SL S/80 81/2 21/2 6 51/4 21/16 1/ n Size designation indicates load rating in kips. 0 Field Welded Adjustable Rigid Strut Part 2252 For sizes and dimensions refer to Part 2250 above. SIZE RANGE : 700 to 130,000 pounds load. MATERIAL: Carbon steel except load pin which is stainless steel. SERVICE: For rigid restraint applications where pin to pin dimension is to be determined in the field. All struts will be shipped at maximum pin to pin dimension. INSTALLATION: Determine pin to pin dimension, cut strut tube to required length and weld adapter end to strut. Securely fasten end bracket to structure. Adjust strut to desired overall length. Fasten strut to pipe attachment (in place). After all minor adjustments are made, the unit is locked by tightening the hex nuts against the extension piece. NOTE: Rods should be visible in the sight holes at each end of the strut to assure proper thread engagement. One end shipped loose for field welding. FIELD ADJUSTMENT : Plus or minus four inches after final welding. ORDERING: Specify part number, size, and customer mark number (if any). 0

5 Short Strut Hydraulic Snubber 10 Part 2525 SIZE RANGE : Available in seven sizes from 3,000 to 130,000 pounds and stroke lengths of 6, 12, and 18 inches. SERVICE: For dynamic restraint applications requiring the smallest overall assembly length in tight fit applications. PISTON ROD SETTING: The factory will preset and clamp the piston rod at the proper cold installing stroke position. Unless specified otherwise, this setting will position the piston so that its calculated thermal movement will straddle the mid-stroke position of the unit, giving equal reserve at each end of the stroke. See Installation Instructions to determine or change piston rod setting. USED WITH : Bergen-Paterson parts 6175, 6202, 6222, 6252, 6520, 6521, 6525, ORDERING: Specify part number, size, cylinder stroke, thermal movement and direction (tension or compression), preset, overall assembly length (pin to pin in inches), options (if any), and customer mark number (if any). Restraint attachments must be ordered separately. Sizes Cyl P to Pt Bore Min. A Inches E H* LAt L 1 P R S T Weight A Preset lbs. Min. Max.A (APPROX.) 3 11/2 223/4 ; 21/ /4 41/2 1/2 11/4 13/4 5 3/ / /4 61/4 3/a 2 21/2 7 3/ / s / /4 81/2 221/ /2 11/2 3/a ' 101/4 23 ' 10 11/ /2 111//, 3/ /4 61/4 1 T7/ /4 13/ /16 1 3/ /16 81/ /2 6 51/4 121/16 1 3/ n Size designation indicates load rating in kips. t Unit length fully retracted. Dimensions shown are for 6" stroke unit. For 12" and 18" stroke units add stroke difference. * Envelope radius. Adjustable Strut Hydraulic Snubber Part Sizes 100 Inches Weight P to P t Pipe lbs. Min. A Max. L1 Size (APPROX.) Torque 0 ft.-lbs. (NOMINAL) S/ /2 S/ /4 ^ 3 S/ /2 S/ / /4 5 S/ /4 ' /4 6 S/ / /8 1 8 S/ SIZE RANGE: Available in seven sizes from 3,000 to 130,000 pounds and stroke lengths of 6, 12, and 18 inches. SERVICE: For dynamic restraint applications allowing the greatest amount of field adjustment or where the exact overall length must be determined on-site. USED WITH: Bergen-Paterson parts 6175, 6202, 6222, 6252, 6520, 6521, 6525, ORDERING: Specify part number, size, cylinder stroke, thermal movement and direction (tension or compression), preset, overall assembly length (pin to pin in inches), options (if any), and customer mark number (if any). Restraint attachments must be ordered separately. For dimensions not given refer to Part 2525 above. n Size designation indicates load rating in kips. Dimensions shown are for 6" stroke units. For 12" and 18" stroke units add stroke difference. t Unit length snubber full retracted. Weight shown is for minimum P to P and 6" stroke unit.

6 PIPE CLAMPS AND ATTACHMENTS Restraint Yoke Clamps Part On Axis Q TORQUE I LOAD 10 (TYP).f1\^/jln T SIZES.7 through 60 SIZE RANGE : 700 to 130,000 pounds load. MATERIAL: Carbon steel except U-bolt which is alloy steel and load pin which is stainless steel. FINISH : Black. MAX. TEMP.: 650 F. SERVICE: For non-integral on-axis attachment to the T piping system in restraint applications. USED WITH : Bergen-Paterson parts 2015, 2250, 2252, 2525, SIZES 80 and 130 ORDERING: Specify part number, load size and pipe size. Strut assembly must be ordered separately. NOTE: This clamp is designed to function within a 10 cone of action, perpendicular to the pipe. Loading beyond this cone is not recommended. Load Size Inc hes Torque Q (kips) D G P T ft.-ibs. (NOMINAL).7 3/4 1/ /4 s 1/ /4 5 '/2 11/4 32 T 11/4 7 3/4 13/ /4 7 3/4 13/ / /2 11/2 11/ /2 1 t' 11/2 31/ /4 j 33 13/ /16 21/ , 1 Pipe Size E W t. E W t. E W t. E W t. E W t. E W t. E W t. E W t. E W t. E W t / /2 5 61/2 51/2 61/2 6 81/ / / / /16 61/ / / / / / /16, / / / / / / / /g / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / /

7 0 0 1 O Restraint Pipe Clamps Part Carbon Steel Part Alloy Steel SIZES.7 through 35 SIZES 60 and 80 SIZE 130 Part 6202 SIZE RANGE : 700 to 130,000 pounds of force in various pipe sizes from 3/4 through 36 inches. MATERIAL: Carbon steel except the load pin which is LOAD stainless steel. I ^,10 (TYP1 SERVICE: For non-integral on-axis attachment to the piping system in restraint applications. MAX. TEMP.: 650 F for the rated loads shown. FEATURES: Designed for use with spherical ball bushings. Tight tolerances provide for low lost motion. Interchangeable with a variety of Bergen-Paterson struts. USED WITH : Bergen-Paterson parts 2015, 2250, 2252, 2525, ORDERING: Specify part number, load size, and pipe size. Strut attachment must be ordered separately. NOTE: This clamp is designed to function within a 10 cone of action perpendicular to the pipe. Loading beyond this cone is not recommended. Part 6222 SIZE RANGE: Same as 6202 adjusted for temperature. MATERIAL: Chrome molybdenum steel, except pin which is stainless steel and bolts which are alloy steel. MAX. TEMP.:1100 F. Load sizes shown must be multiplied by 0.3 for service at 1100 F. ORDERING: Specify part number, load size, and pipe size. Strut attachment must be ordered separately. INSTALLATION NOTE: Tension bolts to remove slack, (while maintaining dim. "G") plus 1/2 turn of the nut. Then lock jam nut to full nut. Pipe Load Size (kips) Size E W Wgt. E W W t. E W W t. E W t. E W Wgt. E W W t. E W Wgt. E W Wgt. E W W t. E W Wgt. 3/4 41/4 1'/2 2 41/ /2 11/2 2 41/ /4 43/4 11/2 2 43/ /2 43/4 11/2 2 43/ / /2 53/4 11/2 3 53/ / /4 21/ / / / /4 21/ / / / /2 11/2 4 71/ / /4 41/ /4 41/ / / /2 41/ /2 41/ / / / /2 41/ /2 41/ / / / , / / '/ / / / /4' / / / / / / / / / / '/ ' / '/ / G D P 17/32 21/32 5/8 3/4 3/8 1/2 21/32 7/8 1/2 29/32 29/32 11/ /4 3/4 21/ /32 2% 11/4 13/4 21/4 17/8 3 23/32 31/s 11/2 1 13/4 1 21/2-6_ - fi'r

8 Off Axis Restraint Pipe Clamp Part 6252 SIZE RANGE: 700 to 60,000 pounds of force in various pipe sizes from 11/2 through 36 inches. MATERIAL: Carbon steel except the load pin which is stainless steel. SERVICE: For non-integral off-axis attachment to the piping system in restraint applications. MAX. TEMP.: 650 F for the rated loads shown. USED WITH : Bergen-Paterson parts 2015, 2250, , ORDERING: Specify part number, load size, and pipe size. Strut attachment must be ordered separately. NOTE: This clamp is designed to function within a 10 cone of action and a 90 arc of loading. Loading beyond the cone or arc is not recommended. INSTALLATION NOTE: Tension bolts to remove slack, (while maintaining dimension "G") plus 1/2 turn of nut. Then lock jam nut to full nut. 11 i i Typel Type U Inches Pipe Size E W W t. E _±_ W W. E W W t. E W W t. E W W t. E W W. 11/2 43/ /2 53/4 21/2 8 53/ / / / / / / /2 21/ / / / / / / / / / / / / / / / / / / / /2t / /2 223/ / / / / / / G 17/32 21/32 21/32 29/32 29/32 17/16 117/32 13/4 0 7/16 5/8 7/8 11/4 11/4 21/4 25/6 21/4 P 3/g 1/2 1/2 3/4 3/4 1 11/4 1 S Sizes above solid line are Type I: below are Type II.

9 Restraint Pipe Clamps Part 6520, 6525 Part 6521, 6526 LOAD i /x.10 trrf) Part 6520, 6521 SIZE RANGE : 700 to 1500 pounds of force in various pipe sizes from 1/2 through 21/2 inches. MAX. TEMP.: 350 F (11/2" insulation max.) Part 6525, 6526 SIZE RANGE : 700 to 1500 pounds of force in various pipe sizes from 1/2 through 21/2 inches. MAX TEMP.: 650 F (21/2" insulation max.) MATERIAL: Carbon steel except the load pin which is stainless steel. SERVICE: For non-integral on-axis attachment to the piping system in restraint applications. FEATURES: Designed for use with spherical ball bushings. Tight tolerances provide for low lost motion. Interchangeable with a variety of Bergen-Paterson struts. INSTALLATION NOTE: Torque u-bolts to 15 ft.-lbs. (nominal). Then lock jam nut to full nut. PIN ORIENTATION : Parts 6520 & 6525 are perpendicular to pipe center line. Part 6521 & 6526 are parallel to pipe center line. NOTE: This clamp is designed to function within a 10 cone of action perpendicular to the pipe. Loading beyond this cone is not recommended. USED WITH : Bergen-Paterson parts 2015, 2250, 2252, 2525, ORDERING: Specify part number, load size, and pipe size. Part 6520,6521 ( 11/2 "Insulation Max.) Pipe Load Size. 7 Load Size 1.5 Size A B E G P R Wgt. A B E G P R Wgt. 1/2 31/4 23/4 9/1 r,.51 % 1/ /4 31/ /2 3/a 3 3/4 31/4 23/ % 1/ / /2 3/ / % 1/ / /2 3/4 3 11/4 4 33/ /2 3 41/4 33/4 37/.63 1/2 3/4 4 11/2 4 33/4 31/16.51 % 1/2 3 41/4 33/4 39/ /2 3/ /2 3 41/4 41/ /2 3/a 4 21/2 41/4 41/ / 1/2 3 41/4 41/2 41/ / Part 6525,6526 ( 21/2 "Insulation Max.) Pipe Load Size. 7 Load Size 1.5 Size A B E G P R Wgt. A B E G P R Wgt. E 1/2 31/4 23/4 31/2.51 % 1/ /4 33/4.63 1/2 3/ /4 31/4 23/4 1 39/16 ' / / /2 3/a / / /13 1/ / /2 3/ / /2 3 41/4 33/ /2 I 3/a 5 11/2 4 33/ /2 3 41/4 33/4 41/4.63 1/2 3/ /4 41/ /2 3 41/4 41/4 41/2.63 1/2 3/a 5 21/2 41/4 41/2 411/ /a 1 1/2 3 41/4 41/ /2 3/4 5

10 Restraint Riser Clamps Part 6280 Carbon Steel Part Alloy Steel Part Carbon Steel MATERIAL Carbon steel except load pin which is stainless steel. FINISH: Black. MAX. TEMP.: 650 F. SERVICE For axial restraint of vertical or horizontal piping where two struts are required. Load is carried by shear lugs which are welded to the pipe. ORDERING: Specify part number, exact pipeo.d., load, operating temperature, C-C dimension and strut size. Strut assembly must be ordered separately. Part Alloy Steel MATERIAL Chrome molybdenum steel except load pin which is stainless steel. FINISH: Black. MAX. TEMP.: 1100 F. SERVICE For axial restraint of vertical or horizontal piping where two struts are required. Load is carried by shear lugs which are welded to the pipe. ORDERING: Specify part number, exact pipe O.D., load, operating temperature, C-C dimension and strut size. Strut assembly must be ordered separately. Refer to the Bergen -Paterson Riser Clamp Bulletin to aid in sizing and selecting the appropriate restraint riser clamp. TYPE 2 TYPE 3 0

11 BERGEN-PATERSON PIPESUPPORT CORP. GENERAL OFFICE: 74 COMMERCE WAY WOBURN, MASS SALES & ENGINEERING WOBURN, MASS. CHICAGO, ILL HEMPSTEAD, N.Y. LOS ANGELES, CALIF. PITTSBURGH, PA. HAYWARD, CALIF. HOUSTON, TX ATLANTA, GEORGIA CLIFTON, NJ. MANUFACTURING: LACONIA, N.H. CHICAGO, ILL MOULTON, AL