75 Ω BNC Style Connector

Size: px

Start display at page:

Download "75 Ω BNC Style Connector"

Diane Holland
5 years ago
Views:

7 Ω BNC Style Connector Frequency Range Characteristic Impedance 7 Ω FETURE 7 Ω of BNC style connector BNC style connectors can be mated. Bayonet coupling mechanism for reliable connection.

at V DC Contact Resistance m Ω Max. V.S.W.R. 1. max. at DC to 1GHz Operating Temperature - +8 * The specifications are typical but may not apply to all connectors.

1 7 Ω BNC Style Connector Frequency Range Characteristic Impedance 7 Ω FETURE 7 Ω of BNC style connector BNC style connectors can be mated. Bayonet coupling mechanism for reliable connection. ock Type Bayonet PPICTIONS Measurement Equipment, Broadcasting, HDTV SPECIFICTIONS Characteristic Impedance 7 Ω Rated Voltage VC(r.m.s.) Dielectric Withstanding Voltage 1V C(r.m.s.)for1 minute Insulation Resistance 1M Ω Mim. at V DC Contact Resistance m Ω Max. V.S.W.R. 1. max. at DC to 1GHz Operating Temperature - +8 * The specifications are typical but may not apply to all connectors. Please check the specifications on each item with its drawing from us when you use. MTERI/FINISH Item Material / Shell () Copper lloy / Ni or g Plating Contact (Male) Copper lloy / g or u Plating Contact (Female) Copper lloy / g or u Plating PTFE Gasket Silicon Rubber 1818

2 Unit:mm Straight Plug BNC7-P-1.CQEW-CF Insutruction 1.C-W. Ni u CR-H-11 1.C-QEW BNC7-P-.CW-CR1B-CF.C-XW 6. Ni u 1 CR-H-11.C-W 1. 9 BNC7-SP-CV-CR1-D1 C-V 6. Ni u 1. ±. φ 9 ±. -φ BNC7-P--CF C-V 7 g g ±. 9 BNC7-P-CW-CF C-W 7 Ni g ±. BNC7-SP-CFB-CF C-FB 9 -φ Ni g φ φ. φ11. BNC7-SP-1.CC-EXBV-CF 1.CC-EXBV ±. Ni u CR-H-111 ±. φ11. ±. φ. Straight Jack ±. -φ. φ11.7 φ φ9. BNC7-J-.CW-CR1-CF.C-XW ±..C-W -φ. ±. Ni u CR-H-11 φ1. Please acknowledge that the specification etc. of this catalog might change φ9. by the improvement etc. without notice. ±. 18. ±.

3 Straight Bulkhead Jack φ BNC7-BJ-.CW-CR1-CF.C-W.C-QEW Ni u Straight Panel Jack Crimp Tool BNC7-PJ-CW-CR1B-CF C-WS Ni u CR-H-11 BNC7-PJ-CV-CR1-CF C-V 11.. Ni u CR-H ±. 1. ±. Panel Mounting Dimensions ±. 9 ±. BNC7-PJ-1.CC-EXBV-CF 1.CC-EXBV. Ni-φ u CR-H-111 BNC7-PJ-1.CV-CR-CF 1.C-V 1.C-QEV. Ni u CR-H-111 BNC7-PJ-.V-CR-Ni-CF.C-V. Ni g CR-H-11 φ -φ φ11. ±. φ. ±. Panel Mounting Dimensions -φ.

4 Unit:mm Receptacle Jack BNC7-R--CF Ni u -φ. φ9. ±. ±. Panel Mounting Dimensions

5 (1) Parts Configulration Heat-shrinkable tube Ferule Sleeve Contact Insert the heat-shrinkable tube into the cable and cut the cable as fig.1. Please be carefule to not damage the outer conductor. Heat-shrinkable tube Sheath Ferule Insert the ferule from the end of outer conductor to the sheath. Spread the top of outer conductor and insert the Sleeve sleeve between insulator and outer conductor. To push the sleeve into the cable, please refer to Push into sleeve on this side min. Inserting Too for Sleeve the tool as fig.. nd cut the outer conductor along the sleeve. 7.. Cut the insulator and center conductor as fig.. Cut the center conductor after pre-soldering. (Pre-soldering) Soldering Contact Insert the insulator and solder the center conductor and contact. Pre-solder the contact. Shave the extra solder from the contact along the No gap round of contact. Inser above cable into the body. nd insert the contact. 6 Crimping position is as fig.6. 6 BNC7-P-.CW-CR1B-CF CR-H-11 BNC7-P-CW-CR1B-CF CR-H Cover the heat-shrinkable tube on the root of the connector body and heat up the tube. Heat-shrinkable tube

6 Unit:mm () Parts Configulration Boot Ferule Sleeve Contact The cable length require for the double-ended cable assembly. -1mm Insert the boot into the cable and cut the cable as fig.1. Please be carefule to not damage the outer conductor. Boot Sheath Ferule Sleeve Insert the ferule toward outer conductor. Spread the outer conductor and press in the sleeve with stripper (P/N:891). Pull out the edge Stripper(P/N:891) Cut the extra outer conductor and insulator from the stripper along the surface as fig.. Cut the insulator and center conductor along this side Push the edge of the stripper and rotate. Separate the insulator toward the arrow. Cut the outer conductor along the surface of sleeve. Cut off the outer conductor 6

7 () Crimping Hole Pinch the contact in the crimping hole(center hole) and insert the center conductor of the cable. Crimp the contact (match the side hole of contact with the curve of crimping hole of tool.).8. Contact Crimped 6 Push the crimp tool into the root of body. 6 Insert the above contact into the body until the top of the contact is same level of the top of insulator. Please do not rotate the body and cable before crimping. Crimp the root of the body as fig.6. Crimp Position 7 7 Cover the boot on the body. Boot 7

8 Unit:mm () Parts Configulration Nut Washer Gasket Clamp Male Contact Plug Shell Cut the cable as fig.1 Please be carefule to not damage the outer conductor. Insert the nut, washer, gasket and clamp as fig.. The clamp is holded on the sheath and pick the outer conductor. 6 Cut the insulator and center conductor. Turn down the outer conductor to the clamp and cut the outer conductor along the clamp. Cut the insulator and center conductor as fig.. Please be careful to not damage the center conductor. Solder up the contact to the center conductor. Please be careful to not be swelled up the solder. Please be careful to not gap between contact and insulator. Please be careful to not deform the insulator by soldering. Inser the above contact into the body and screw up the nut. Please screw up the nut by wrench. 8

9 () Parts Configulration Heat-shrinkable tube Ferule Sleeve Contact 1 1 Insert the heat-shrinkable tube into the cable and cut the cable as fig.1. Heat-shrinkable tube Sheath Cut off extra outer conductor Ferule. Sleeve Soldering Insert the ferule on the outer conductor. Pick the outer conductor and spread the top of center conductor. Insert the insulator from the outer conductor. Cut the extra outer conductor along the sleeve. Cut the insulator in length. Cut the center conductor after pre-soldering. BNC7-J-.CW-CR1-CF BNC7-PJ-CW-CR1B-CF Insert the insulator and solder the contact. 7.mm 6.8mm Contact Same level Insert the above contact into the body and crimp the body as fig.. BNC7-J-.CW-CR1-CF CR-H-11 BNC7-PJ-CW-CR1B-CF CR-H-11 Cover the heat-shrinkable tube on the root of the connector body and heat up the tube. Heat-shrinkable tube 9

N Series. N Type Connectors CONFORMING STANDARD SPECIFICATION MATERIAL/FINISH JIS-C-5411 MIL-C-39012

N Series. N Type Connectors CONFORMING STANDARD SPECIFICATION MATERIAL/FINISH JIS-C-5411 MIL-C-39012 N Type Connectors N series is the most practical coaxial cable connectors for 7mm (inner diameter of outer conductor) of 50Ω group. High frequency performance is superior. Many types of connectors are