Drying Tumblers 55 Pound Capacity

Transcription

1 Drying Tumblers 55 Pound Capacity Refer to Page 5 for Model Numbers Parts T478C_ Part No R8 February 2012

2

3 Table of Contents Title Page Parts Ordering Information... 3 Serial Plate Location... 3 Model Identification... 5 Product Overview - Heat Source and Voltage... 6 Product Overview - Control Suffixes (Drawing 1 of 3)... 8 Product Overview - Control Suffixes (Drawing 2 of 3) Product Overview - Control Suffixes (Drawing 3 of 3) Dual Digital Timer Control Components DX4 Control Components DMP Control OPL Microprocessor Controls Coin Drop Components for MDC Models BY Control Option for MDC Models Coin Drops Coin Drop Components for Electronic Control Models Card Reader Components for Electronic Control Models Coin Drop Components for Quantum Control Card Reader Components for Quantum Control Network Board for Quantum Control Communication Board for Quantum Control UniLinc Control LED OPL Control Door and Hinge Components Front Panel Assemblies and False Fronts Cabinet Front Components Emergency Stop Button for CE Models Lower Cabinet Components Cylinder Components Cabinet Components Fire Suppression System Components Fire Suppression System Control Box Drive Motor Components Blower Components Moisture Sensing Components Rotation Sensor Airflow Switch Gas Burner Housing and Secondary Stove Limit Gas Valve Assembly - Non-CE and Non-Australian Gas Models Gas Valve and Piping - CE and Australian Gas Models Electric Heater Components Control Tray Harnesses for Gas Models Copyright 2012, Alliance Laundry Systems LLC All rights reserved. No part of the contents of this book may be reproduced or transmitted in any form or by any means without the expressed written consent of the publisher

4 Control Tray for Non-CE and Non-Australian Gas Models Control Tray Components for CE and Australian Gas Models Control Tray Harnesses for Electric Models Control Tray for Non-CE Electric Models Control Tray for CE Electric Models Accessory Box Harnesses for Electric Models Accessory Box for Non-CE Electric Models Accessory Box for CE Electric Models Parts Index

5 If literature or replacement parts are required, contact the source from whom the machine was purchased or contact Alliance Laundry Systems at (920) for the name and address of the nearest authorized parts distributor. Parts Ordering Information For technical assistance, call either of the numbers listed below: (920) Ripon, Wisconsin Wevelgem, Belgium When calling or writing about your product, be sure to mention model and serial numbers. Model and serial numbers are located on serial plate(s) as shown. Serial Plate Location Serial Plate TMB2098N_

6 Notes

7 Model Identification Information in this manual is applicable to these tumbler models: CA055L CA055N CT055E CT055L CT055N CU055E CU055L CU055N DR55SE2-BT055E DR55SE2-BU055E DR55SG2-BA055L DR55SG2-BA055N DR55SG2-BT055L DR55SG2-BT055N DR55SG2-BU055L DR55SG2-BU055N GA055L GA055N GT055E GT055L GT055N GU055E GU055L GU055N HA055L HA055N HT055D HT055E HT055L HT055N HU055E HU055L HU055N IPD55E2-IT055E IPD55G2-IT055L IPD55G2-IT055N KA055L KA055N KT055E KT055L KT055N KU055E KU055L KU055N SA055L SA055N ST055D ST055E ST055L ST055N SU055E SU055L SU055N UA055L UA055N UT055E UT055L UT055N UU055E UU055L UU055N

8 Product Overview - Heat Source and Voltage DESIGN MODEL NO. SERIAL NO. ST055NBCA1G2W VAC. 60 Hz 9.3 AMP 1 Ph 2 WIRES + GROUND 14 REC. AWG WIRE SIZE RECOMMENDED CIRCUIT BREAKER : 15 AMPS WIRING DIAGRAM PART NUMBER: CERTIFIED ANS Z21.5.2bCSA 7.2b-2003 CLOTHES DRYER, VOL.II ANS Z21.5.2bCSA 7.2b-2003 Secheuses, VOL.II C US TMB2818P_

9 Product Overview - Heat Source and Voltage REF PART NO. DESCRIPTION COMMENTS 1 - Heat Source D: Liquid Petroleum Gas (L.P.) E: Electric L: Liquid Petroleum Gas (L.P.) N: Natural Gas (N.G.) 2 - Voltage A1: 100, 200 Volt/50 Hertz/1 Phase A2: 100, Volt/60Hertz/1 Phase B2: 120, Volt/60 Hertz/1 Phase; For high Amp motors B3: 120, Volt/60 Hertz/1 Phase; For low Amp motors F1: 200 Volt/50 Hertz/1 Phase F2: 200 Volt/60 Hertz/1 Phase F4: 200 Volt/50 Hertz/3 Phase F5: Volt/60 Hertz/3 Phase F6: , 240 Volt/60 Hertz/3 Phase G1: 208 Volt/60 Hertz/1 Phase G2: Volt/60 Hertz/1 Phase J1: 230 Volt/50 Hertz/1 Phase J2: Volt/50 Hertz/1 Phase J4: 240 Volt/60 Hertz/1 Phase J5: 230 Volt/50 Hertz/3 Phase J6: Volt/50 Hertz/3 Phase J8: 240 Volt/60 Hertz/3 Phase M1: 380 Volt/50 Hertz/3 Phase M2: 380, Volt/50 Hertz/3 Phase M3: 380 Volt/60 Hertz/3 Phase N1: Volt/50 Hertz/3 Phase P1: 440 Volt/60 Hertz/3 Phase Q1: Volt/60 Hertz/3 Phase

10 Product Overview - Control Suffixes (Drawing 1 of 3) DESIGN MODEL NO. SERIAL NO. ST055NBCA1G2W VAC. 60 Hz 9.3 AMP 1 Ph 2 WIRES + GROUND 14 REC. AWG WIRE SIZE RECOMMENDED CIRCUIT BREAKER : 15 AMPS WIRING DIAGRAM PART NUMBER: CERTIFIED ANS Z21.5.2bCS A 7.2b-2003 CLOTHES DRYER, VOL.II ANS Z21.5.2bCS A 7.2b-2003 Secheuses, VOL.II C US or S E L E C T INS E R T INS E R T P US H T E MP C OIN C A R D S T A R T 25 C DRYING COOL DOWN START 3O, 3V and 3X Control Suffixes BC and BX Control Suffixes 1 S L E C T T E MP 2 INS E R T C A R D 3 P US H S T A R T DRYING COOL DOWN START DRYING COOLING TEMPERATURE BL and BY Control Suffixes REV START STOP (CANCE L) DO Control Suffix or S L E C T INS E R T INS E R T P US H T E MP C OIN C A R D S T A R T 25 C INS E R T COINS/CARD DR YING COOL DOWN START DV and DX Control Suffixes NC and NX Control Suffixes TMB2819P_

11 Product Overview - Control Suffixes (Drawing 1 of 3) REF PART NO. DESCRIPTION COMMENTS 1 - Control - Nonreversing 3O: DX4 OPL 3V: DX4 vended 3X: DX4 prep for coin 2 - Control - Nonreversing BC: basic electronic, coin BX: basic electronic, prep for coin 3 - Control - Nonreversing BL: basic electronic, central pay BY: basic electronic, prep for card 4 - Control - Nonreversing DO: DMP OPL 5 - Control - Nonreversing DV: DMP vended DX: DMP prep for coin 6 - Control - Nonreversing NC: NetMaster coin NX: NetMaster, prep for coin NOTE: Coin models have the following control suffixes: 3V, 3X, BC, BX, DV, DX, NC and NX NOTE: OPL models have the following control suffixes: 3O, BL, BY and DO

12 Product Overview - Control Suffixes (Drawing 2 of 3) All Models Except D Models DESIGN MODEL NO. SERIAL NO. ST055NBCA1G2W VAC. 60 Hz 9.3 AMP 1 Ph 2 WIRES + GROUND 14 REC. AWG WIRE SIZE RECOMMENDED CIRCUIT BREAKER : 15 AMPS WIRING DIAGRAM PART NUMBER: CERTIFIED ANS Z21.5.2bCSA 7.2b-2003 CLOTHES DRYER, VOL.II ANS Z21.5.2bCSA 7.2b-2003 Secheuses, VOL.II C US 1 SELECT TEMP 2 INSERT CARD 3 PUSH START INSERT REMOVE CARD CARD ADD TIME DRYING COOL DOWN START ON / SELECT HIGH MEDIUM MED LOW LOW NO HEAT START STOP/RESET TEMP DISPLAY F/ C SIGNAL STATUS DRYING COOL DOWN DOOR OPEN CUSTOM * AUTO AUTO SPECIAL CYCLE AUTO TEMP CONDITION PROGRAM * TIME SPECIAL TIME COOL DOWN MORE LESS + -- SAVE CUSTOM PROG NY Control Suffix OM Control Suffix or SELECT INSERT INSERT PUSH TEMP COIN CARD START 25 C QT Control Suffix LC, LX, LY, WC, WX and WY Control Suffixes TMB2931P_

13 Product Overview - Control Suffixes (Drawing 2 of 3) REF PART NO. DESCRIPTION COMMENTS 1 - Control - Nonreversing NY: NetMaster, prep for card 2 - Control - Nonreversing OM: OPL micro 3 - Control - Nonreversing QT: dual digital timer 4 - Control - Nonreversing LC: network adaptable coin LX: network adaptable, prep for coin LY: network adaptable, prep for card WC: network ready coin WX: network ready, prep for coin WY: network ready, prep for card NOTE: Coin models have the following control suffixes: LC, LX, LY, WC, WX and WY NOTE: OPL models have the following control suffixes: NY, OM and QT

14 Product Overview - Control Suffixes (Drawing 3 of 3) DESIGN MODEL NO. SERIAL NO. HT055NEOF6G1W VAC. 60 Hz 9.3 AMP 1 Ph 2 WIRES + GROUND 14 REC. AWG WIRE SIZE RECOMMENDED CIRCUIT BREAKER : 15 AMPS WIRING DIAGRAM PART NUMBER: CERTIFIED ANS Z21.5.2bCSA 7.2b-2003 CLOTHES DRYER, VOL.II ANS Z21.5.2bCSA 7.2b-2003 Secheuses, VOL.II C US PROGRAM ENERGY SAVER HEATING STOP BACK START UO Control Suffix EO Control Suffix 1 Load clothes Cargue ropa 2 Close door Cierre la puerta PROGRAM ENERGY HEATING SAVER PROGRAM ENERGY SAVER HEATING 3 Select cycle Seleccione ciclo STOP 4 Push START Presione INICIO BACK START EO Control Suffix EO Control Suffix ECO BACK PROSERIESII EO Control Suffix EO Control Suffix TMB3149P_

15 Product Overview - Control Suffixes (Drawing 3 of 3) REF PART NO. DESCRIPTION COMMENTS 1 - Control - Nonreversing U models; UO: UniLinc OPL 2 - Control - Nonreversing S models; EO: LED OPL 3 - Control - Nonreversing H models; EO: LED OPL 4 - Control - Nonreversing U models; EO: LED OPL 5 - Control - Nonreversing C, D and I models; EO: LED OPL 6 - Control - Nonreversing G and K models; EO: LED OPL NOTE: OPL models have the following control suffixes: EO and UO

16 Dual Digital Timer Control Components C, H, I, S and U Models G and K Models Starting 1/16/12 Models with QT Control Suffix TMB2646P_

17 Dual Digital Timer Control Components REF PART NO. DESCRIPTION COMMENTS NA P Control Set Includes items 1, 2, 4-8, 10, 12-16, 19, 20 and Nut Screw Main Harness Assembly Electric models need Harness Strap to hold harness out of the way of heater elements; Models through 7/31/ Main Harness Electric models need Harness Strap to hold harness out of the way of heater elements; Models starting 8/1/ Control Chassis Mounting Bracket P Control Assembly P Control Panel Harness P Display Assembly Nut Jumper Calibration Wire Panel Locator 11 M4860P3 Buzzer Kit Includes buzzer, bracket and harness Male Tab Terminal Temperature Selector Switch Temperature Selector Switch Bracket Nut Temperature Knob Bypass Harness Foam Gasket Rocker Switch Start Rocker Switch Overlay Screw Control Plate Assembly

18 DX4 Control Components D and I Models with 3O, 3V and 3X Control Suffixes TMB3156P_

19 DX4 Control Components REF PART NO. DESCRIPTION COMMENTS Foam Gasket Graphic Overlay OPL; Models through 7/31/ Graphic Overlay OPL; Models starting 8/1/ Graphic Overlay Coin; Single drop; Models through 7/31/ Graphic Overlay Coin; Single drop; Models starting 8/1/ Graphic Overlay Coin; Dual drop; Models through 7/31/ Graphic Overlay Coin; Dual drop; Models starting 8/1/ P Control Plate Kit Sleeve 4 required P Control Assembly 3O control suffix P Control Assembly 3V and 3X control suffixes Nut Control Panel Harness Assembly Australian and CE models P Control Panel Harness All other models

20 DMP Control C and I Models with DO, DV and DX Control Suffixes Coin Models Through 4/1/10; OPL Models Through 7/31/11 Coin OPL TMB3013P_

21 DMP Control REF PART NO. DESCRIPTION COMMENTS P Membrane Switch Coin; DV and DX control suffixes Control Plate Assembly Coin; Includes studs; DV and DX control suffixes Nut P Electronic Control P Coin Drop Assembly United States; $ Coin Drop Assembly Mexico; 2 peso Coin Drop Assembly Token; Coin Drop Assembly Japan; 100 yen Coin Drop Assembly England; 20 pence Coin Drop Assembly Token; Coin Drop Assembly England; 50 pence Foam Gasket Relay/Buzzer Bracket 8 M Relay 9 M Screw Male Tab Terminal Adjustable Buzzer Control Plate Assembly OPL; Includes studs; DO control suffix P Membrane Switch OPL; DO control suffix

22 HIGH STOP/RESET TEMP DISPLAY DRYING AUTO CONDITION LESS SAVE CUSTOM PROG OPL Microprocessor Controls G and K Models H, S and U Models Through 7/31/11 Models with OM Control Suffix ON / SELECT MEDIUM MED LOW START STATUS LOW COOL DOWN PROGRAM NO HEAT F/ C SIGNAL DOOR OPEN CUSTOM AUTO * SPECIAL CYCLE AUTO TEMP MORE + -- TIME * SPECIAL TIME COOL DOWN TMB3024P_

23 OPL Microprocessor Controls REF PART NO. DESCRIPTION COMMENTS NA M4689P3 Electronic OPL Control Kit Dual secondary transformers (M Transformer for VAC and M Transformer for VAC) must be used with this kit; Does not include overlay or harness Bypass Harness P Control Panel Harness 3 M413930P Ferrite Core Assembly Main Harness Assembly Electric models need Harness Strap to hold harness out of the way of heater elements; Models through 7/31/ Main Harness Electric models need Harness Strap to hold harness out of the way of heater elements; Models starting 8/1/ Jumper Calibration Assembly P Control Kit Fuse 1.25 Amp Nut Control Plate Assembly Includes studs Overlay S and U models; Icon and English Overlay S and U models; Icon Overlay H models; Icon and English Overlay H models; Icon Overlay G and K models Foam Gasket

24 1 SELECT TEMP 2 INSERT CARD 3 PUSH START 25 C Coin Drop Components for MDC Models H, K and S Models with BC, BL and BX Control Suffixes TMB3015P_

25 Coin Drop Components for MDC Models REF PART NO. DESCRIPTION COMMENTS Pushbutton Switch Screw 4 required for mounting control Jumper Calibration Wire P Control Panel Harness Control panel to main harness P Control Assembly P Coin Vault Switch Harness Nut 3 required Main Harness Assembly Electric models need Harness Strap to hold harness out of the way of heater elements; Models through 7/31/ Main Harness Electric models need Harness Strap to hold harness out of the way of heater elements; Models starting 8/1/ Control Plate Assembly Overlay S models; BC, BL* and BX control suffixes; Text; Single drop Overlay S models; BC, BL* and BX control suffixes; Icon; Single drop Overlay S models; BC and BX control suffixes; Text; Dual drop Overlay S models; BC and BX control suffixes; Icon; Dual drop Overlay H models; BC, BL* and BX control suffixes; Text; Single drop Overlay H models; BC, BL* and BX control suffixes; Icon; Single drop Overlay H models; BC and BX control suffixes; Text; Dual drop Overlay H models; BC and BX control suffixes; Icon; Dual drop Overlay H models; BC, BL* and BX control suffixes; Text; Single drop Overlay K models; Text; Single drop Overlay K models; Text; Dual drop Coin Drop Overlay S models; BL* control suffix; Cover Coin Cover Overlay H models; BL* control suffix; Cover Foam Gasket * NOTE: BL control suffix requires an overlay and overlay cover specific to model

26 1 2 3 BY Control Option for MDC Models H, K and S Models TMB3016P_

27 BY Control Option for MDC Models REF PART NO. DESCRIPTION COMMENTS Overlay S models; Text or icon Overlay H models; Text or icon Overlay K models Pushbutton Switch Control Plate Assembly Screw 4 required Main Harness Assembly Electric models need Harness Strap to hold harness out of the way of heater elements; Models through 7/31/ Main Harness Electric models need Harness Strap to hold harness out of the way of heater elements; Models starting 8/1/ P Control Panel Harness P Control Assembly Jumper Calibration Wire Nut Bypass Harness Slot Card Plate Assembly Included in literature packet Mounting Plate Card Reader Overlay Black; Included in literature packet Card Reader Overlay Gray; Included in literature packet Foam Gasket

28 Coin Drops TMB2921P_

29 Coin Drops REF PART NO. DESCRIPTION COMMENTS NA CK502 Electronic Coin Drop Kit Includes item 2 and wiring diagram supplement NA CK115 Electronic Coin Drop Kit USA and Canada; Also order CK502 Electronic Coin Drop Kit NA CK113 Electronic Coin Drop Kit Japan and Taiwan; Also order CK502 Electronic Coin Drop Kit NA CK099 Electronic Coin Drop Kit Australia (default), New Zealand, Hong Kong, South Korea and Malaysia; Also order CK502 Electronic Coin Drop Kit NA CK100 Electronic Coin Drop Kit United Kingdom (default) and Europe; Also order CK502 Electronic Coin Drop Kit NA CK101 Electronic Coin Drop Kit Europe (default), Denmark and Norway; Also order CK502 Electronic Coin Drop Kit NA CK103 Electronic Coin Drop Kit Lithuania (default), Latvia and Europe; Also order CK502 Electronic Coin Drop Kit NA CK106 Electronic Coin Drop Kit Malaysia (default), China, Russia and Singapore; Also order CK502 Electronic Coin Drop Kit NA CK108 Electronic Coin Drop Kit South Africa; Also order CK502 Electronic Coin Drop Kit NA CK109 Electronic Coin Drop Kit Euro; Also order CK502 Electronic Coin Drop Kit Coin Identification Paper Electronic Coin Drop Harness P Electronic Coin Drop Assembly United Kingdom (default) and Europe Electronic Coin Drop Assembly Europe (default), Denmark and Norway P Electronic Coin Drop Assembly Australia (default), New Zealand, Hong Kong, South Korea and Malaysia Electronic Coin Drop Assembly Mexico (default), Ecuador and United States Electronic Coin Drop Assembly Lithuania (default), Latvia and Europe Electronic Coin Drop Assembly Malaysia (default), China, Russia and Singapore Electronic Coin Drop Assembly Euro;.10,.20,.50, 1.00 and P Coin Drop USA; $ P Coin Drop USA; Dual; $.25 and $ Coin Drop D models; USA Coin Drop Assembly Japan; 100 yen Coin Drop Assembly Japan; 100 and 500 yen Coin Drop Assembly Australia;.20 and Coin Drop Assembly Australia; 1.00 and Coin Drop Assembly Euro;.20 and Coin Drop Assembly Euro;.50 and P Coin Drop Assembly Token; STD Coin Drop Assembly Token; STD Coin Drop Assembly Token; 7K P Coin Drop Assembly Canada; Coin Drop Assembly Canada;.25 and Coin Drop Assembly England; 20 pence and 1 pound Coin Drop Assembly Korea; 100 and 500 won P Coin Drop Token; STD Coin Drop Assembly Israel; Shekel 3 CK077 Coin Drop Kit Taiwan; 10 NT P Opto Coupler P Wire Guard

30 1 SELECT TEMP 2 INSERT CARD 3 PUSH START 25 C Coin Drop Components for Electronic Control Models K Models Through Serial No with NC and NX Control Suffixes TMB3021P_

31 Coin Drop Components for Electronic Control Models REF PART NO. DESCRIPTION COMMENTS Overlay Single drop Overlay Dual drop Pushbutton Switch Control Plate Assembly Screw For mounting electronic control Jumper Calibration Wire P Control Panel Harness P Control Kit P Coin Vault Switch Harness Nut Main Harness Assembly Electric models need Harness Strap to hold harness out of the way of heater elements Foam Gasket

32 1 2 3 SELECT TEMP INSERT CARD PUSH START Card Reader Components for Electronic Control Models K Models Through Serial No with NY Control Suffix TMB3025P_

33 Card Reader Components for Electronic Control Models REF PART NO. DESCRIPTION COMMENTS Overlay Pushbutton Switch Control Plate Assembly Card ready models Screw P Control Kit Nut Main Harness Assembly Electric models need Harness Strap to hold harness out of the way of heater elements P Control Panel Harness Jumper Calibration Wire Card Reader Network Harness Card reader to network board Assembly Card Reader Harness Assembly Card reader to control P Card Reader and Bracket Assembly Mounting Plate Use with item Foam Gasket

34 Coin Drop Components for Quantum Control S Models with LC, LX, WC and WX Control Suffixes TMB3019P_

35 Coin Drop Components for Quantum Control REF PART NO. DESCRIPTION COMMENTS NA NK206 Network Retrofit Kit LC and LX control suffixes NA NK220 Network Controller Kit LC and LX control suffixes Control Overlay Model ST055D Control Overlay Model ST055D Control Overlay Single drop; All models except ST055D Control Overlay Dual drop; All models except ST055D Pushbutton Switch P Control Plate Kit Screw For mounting item Jumper Calibration Wire P Control Panel Harness P Control Kit P Coin Vault Switch Harness Nut Main Harness Assembly Electric models need Harness Strap; Models through 7/31/ Main Harness Electric models need Harness Strap; Models starting 8/1/ Foam Gasket

36 Card Reader Components for Quantum Control S Models with LY and WY Control Suffixes TMB3020P_

37 Card Reader Components for Quantum Control REF PART NO. DESCRIPTION COMMENTS NA NK206 Network Retrofit Kit LY control suffix NA NK220 Network Controller Kit LY control suffix Overlay Pushbutton Switch Control Plate Assembly Screw P Control Kit Main Harness Assembly Electric models need Harness Strap; Models through 7/31/ Main Harness Electric models need Harness Strap; Models starting 8/1/ P Control Panel Harness Jumper Calibration Wire Bypass Harness Slot Card Plate Assembly Mounting Plate Foam Gasket

38 1 2 3 SELECT TEMP INSERT COIN PUSH START HIGH TEMP MED TEMP START LOW TEMP NO HEAT 25 C Network Board for Quantum Control S Models with WC, WX and WY Control Suffixes TMB2928P_

39 Network Board for Quantum Control REF PART NO. DESCRIPTION COMMENTS NA Communication Wire Harness Assembly Control Housing Cover Screw Network Board Assembly P Network Wire Harness Assembly

40 Communication Board for Quantum Control S Models with WC Control Suffix H UPPER/SINGLE LOWER H TMB1935P_

41 Communication Board for Quantum Control REF PART NO. DESCRIPTION COMMENTS P Communication Board PC Board Standoff 4 required Communication Connector

42 UniLinc Control U Models with UO Control Suffix TMB3123P_

43 UniLinc Control REF PART NO. DESCRIPTION COMMENTS Control Plate Assembly Nut Control Assembly Screw P Control Assembly Output Harness Use between item 3 and item Control Panel Harness Goes from item 5 to main harness Main Harness Screw Overlay

44 LED OPL Control C, D, H, I, S and U Models G and K Models Starting 1/16/12 Models with EO Control Suffix TMB3124P_

45 LED OPL Control REF PART NO. DESCRIPTION COMMENTS Overlay S models Overlay H models Overlay C, D and I models Overlay U models Overlay G and K models Control Plate and Studs Assembly Screw Nut Control Assembly P Control Assembly H, S and U models P Control Assembly C, D and I models P Control Assembly G and K models Output Harness Use between item 5 and item Control Panel Harness Goes from item 6 to main harness Main Harness

46 Door and Hinge Components TMB3152P_

47 Door and Hinge Components REF PART NO. DESCRIPTION COMMENTS NA P Replacement Door Handle Kit H models P Door Assembly S and U models; Excludes hinge P Door Assembly H models; Excludes hinge Door Assembly C and I models through 7/31/ Door Assembly C, D and I models starting 8/1/11; Excludes hinge Door Assembly G and K models; Excludes hinge P Door Ring Gasket Nut H, S, and U models; 4 required Nut P Door Switch Actuator Kit * Door Hinge Assembly H, S and U models; C models starting 8/1/ Door Hinge Assembly C, H, S and U models; I models through 7/31/11; Stainless steel B Door Hinge Assembly G and K models; D and I models starting 8/1/ Screw Screw 9 M4772P3 Cam and Hinge Kit C, H, S and U models; I models through 7/31/11 9 M4773P3 Cam and Hinge Kit G and K models; D and I models starting 8/1/ Screw C, H, S and U models; I models through 7/31/ Screw G and K models; D and I models starting 8/1/ Door Hinge Lug Assembly C, H, S and U models; I models through 7/31/ Door Hinge Lug Assembly G and K models; D and I models starting 8/1/ Pin Pop Rivet B Handle Bar G and K models P Door Seal Kit P Door Glass H models P Door Glass All other models 17 M4221P4 Door Glass Installation Tool Pop Rivet G and K models; 4 required Washer G and K models Nameplate Overlay G models; Coin Nameplate Overlay K models; Coin 21 M Nut H, S and U models; For door strike; Mounts between door strike screw and door handle Door Handle S and U models; C, D and I models starting 8/1/ Door Handle H models Door Ring Assembly H, S and U models Door Ring and Handle Assembly C and I models through 7/31/ B Door Ring C, D and I models starting 8/1/ B Door Ring G and K models Screw H, S and U models; Use with door handle Hole Plug C, D and I models; 4 required 25 M Screw All other models * Add Letter To Designate Color. Q - Bisque W - White

48 Front Panel Assemblies and False Fronts TMB3089P_

49 Front Panel Assemblies and False Fronts REF PART NO. DESCRIPTION COMMENTS * False Front 72 inches False Front 72 inches; Stainless steel * False Front 76 inches False Front 76 inches; Stainless steel * Control Panel S and U models Control Panel S and U models; Stainless steel * Control Panel H models Control Panel H models; Stainless steel * Control Panel C models; I models through 7/31/11; QT control suffix Control Panel C models; I models through 7/31/11; QT and SD control suffixes; Stainless steel * Control Panel C models; I models through 7/31/11; DO control suffix Control Panel C models; I models through 7/31/11; DO, DV and DX control suffixes; Stainless steel B Control Panel D and I models starting 8/1/ * Control Panel K models; OM and NC control suffixes Control Panel K models; NC control suffix; Stainless steel * Front Panel Assembly H, K and S models; BC, BX, LC and LX control suffixes Front Panel Assembly H, K and S models; BC, BX, LC and LX control suffixes; Stainless steel *P Front Panel Assembly S models; BL control suffix Front Panel Assembly S models; BL control suffix; Stainless steel * Front Panel Assembly 3O, DO, OM and QT control suffixes P Front Panel Assembly OM and QT control suffixes; Stainless steel Label G and K models; Coin 5 M Warning Label Front Cylinder Seal * Add Letter To Designate Color. Q - Bisque W - White

50 Cabinet Front Components TMB3129P_

51 Cabinet Front Components REF PART NO. DESCRIPTION COMMENTS P Coin Vault Switch Harness Nut Coin Chute Assembly Pushbutton Switch Panel Locator 9 required Screw Control Trim K, S and U models; Black Control Trim H models; Gray Coin Vault Assembly 9 M Shadow Box Clip Expansion Clip 8 required; Use with item 11, between front panel and cabinet Screw Lock Shim Key RL P Lock, Key and Nut Kit RL Pop Rivet 16 M Door Latch Coin Vault Trim W Switch Hole Plug White Q Switch Hole Plug Bisque B Switch Hole Plug Black Access Panel Trim K models; OPL Access Panel Trim K models; Coin Key RL Nameplate Overlay K models; OPL Nameplate Overlay G models; OPL P Lock, Key and Nut Kit RL

52 Emergency Stop Button for CE Models TMB2375P_

53 Emergency Stop Button for CE Models REF PART NO. DESCRIPTION COMMENTS NA F Contact Switch Models starting 10/1/07; Does not include mounting base Contact Block Includes base; Models through 9/30/07 1 F Contact Block Switch Models starting 10/1/07; Includes mounting base P Emergency Stop Contact Harness 1 contact P Emergency Stop Harness 2 contacts 3 M Emergency Stop Label Pushbutton Models through 9/30/07 4 F Emergency Stop Pushbutton Models starting 10/1/

54 Lower Cabinet Components TMB2641P_

55 Lower Cabinet Components REF PART NO. DESCRIPTION COMMENTS Kickplate H models; Dark gray Kickplate All other models; Black Handle and Caps Assembly C, D, I, S and U models; Black Handle and Caps Assembly H models; Dark gray Handle Bumper G and K models * Lint Panel Assembly H models; Coin * Lint Panel Assembly H models; OPL 3 N/A Lint Panel Assembly OM and QT control suffixes Lint Panel Assembly OM and QT control suffixes; Stainless steel * Lint Panel Lint Panel Stainless Steel Screw For attaching handle; 6 required P Lint Panel Gasket Sold per foot Rear Lint Panel Screw Attaching roller catch Nut Roller Catch Wheel Roller Catch Spacer Screw Roller Catch Arm Nut Attaching roller catch Pop Rivet For attaching kickplate; Black; 6 required Pop Rivet For attaching kickplate; Gray; 6 required Panel Locator Screw * Add Letter To Designate Color. L - Almond Q - Bisque W - White N/A = Part no longer available

56 Cylinder Components TMB3162P_

57 Cylinder Components REF PART NO. DESCRIPTION COMMENTS NA P Drywall Screw Magnet Kit Cylinder Assembly G and K models; Non-moisture sensing Cylinder and Trunnion Assembly G and K models; Moisture sensing P Cylinder Assembly All other models; Galvanized; Non-moisture sensing Cylinder and Trunnion Assembly All other models; Galvanized; Moisture sensing P Cylinder Assembly All other models; Stainless steel; Non-moisture sensing Cylinder and Trunnion Assembly All other models; Stainless steel; Moisture sensing Screw 16 required 3 263P4 Cylinder Guide Tool 4 M4963P3 Trunnion and Seal Kit Includes item 8; Also order Adhesive; Non-moisture sensing Trunnion and Wire Assembly Moisture sensing; Includes Trunnion Assembly Screw 10 required Center Cylinder Seal Cylinder Bearing Stud Plate Assembly P Rear Cylinder Seal Use with Adhesive Rear Cylinder Seal Support Rear Bearing Shim Support Bearing Rear Cylinder Bearing Housing 13 M Washer 14 M Nut 15 M Nut 16 M Nut 4 required Rear Cylinder Channel Plate Cylinder Motor Harness Assembly Models through 2/28/10; 1 Phase; 3 Phase electric models with 240 Volt and below Cylinder Motor Harness Assembly Models starting 3/1/10; 1 Phase; 3 Phase electric models with 240 Volt and below Cylinder Motor Harness Assembly Models through 2/28/10; 3 Phase models except electric models with 240 Volt and below Cylinder Motor Harness Assembly Models starting 3/1/10; 3 Phase models except electric models with 240 Volt and below Nut 8 required Washer 8 required Rear Cylinder Channel Non-moisture sensing Rear Cylinder Channel Moisture sensing Screw 8 required End Cap Non-moisture sensing End Cap Moisture sensing

58 Cabinet Components TMB3026P_

59 Cabinet Components REF PART NO. DESCRIPTION COMMENTS NA M4379P4 Tumbler Dolly Kit NA 298P4P Spray Paint White NA 297P4 Spray Paint Almond NA 286P4 Spray Paint Blue NA 122P4P Porcelain Touch-Up Paint White NA 215P4P Porcelain Touch-Up Paint Almond NA 370P4P Porcelain Touch-Up Paint Bisque Top Panel Top Pan Screw *P Side Panel Upper *P Side Panel Lower Nut Leveling Leg Hole Plug Lint Panel Switch Bracket Pop Rivet 16 required; Upper side panel Switch Assembly Center Pan Hold-Down Clip Hold-Down Clip 2 required Lint Screen Sheet Metal Edge Gasket Lower P Roller Bearing Assembly Roller Seal Models starting 3/1/ Roller Shaft Washer 21 M Nut Nut Sheet Metal Edge Gasket Upper Cylinder Shroud Left Cylinder Shroud Right Center Partition * Add Letter To Designate Color. Q - Bisque W - White

60 Fire Suppression System Components TMB2918P_

61 Fire Suppression System Components REF PART NO. DESCRIPTION COMMENTS Union Tee 2 required Spray Nozzle Hose 3 required Tube Assembly Elbow 2 required Screw 20 required Nozzle Hole Cover Nozzle Bracket 3 required Thermistor Plate 2 required Thermistor 2 required Screw 4 required Spray Nozzle 3 required Nozzle Bracket 3 required Tee

62 Fire Suppression System Control Box TMB2912P_

63 Fire Suppression System Control Box REF PART NO. DESCRIPTION COMMENTS Screw 2 M Drive Rivet Control Box Top P Control Harness Control Box Housing Screw Circuit Board Support 4 required P Control Control Box Cover P Lock, Key and Nut Kit RL001 key code; Optional if same key is to be used for control lock Light 12 F Water Hose 2 required Hose Fitting Thermistor 2 required Hose Clamp Hose 14 inches; Outlet hose P Mixing Valve W Push-to-Start Switch 2 required Control Box Base P Sensor Harness Snap Bushing Bracket

64 Drive Motor Components TMB3083P_

65 Drive Motor Components REF PART NO. DESCRIPTION COMMENTS P Belt inches Cylinder Motor Harness Assembly Models through 2/28/10; 1 Phase; 3 Phase electric models with 240 Volt and below Cylinder Motor Harness Assembly Models through 2/28/10; 3 Phase except electric models with 240 Volt and below Cylinder Motor Harness Assembly Models starting 3/1/10; 1 Phase; 3 Phase electric models with 240 Volt and below Cylinder Motor Harness Assembly Models starting 3/1/10; 3 Phase except electric models with 240 Volt and below Screw 2 required Motor Conduit Mounting Bracket Drive Motor 100 or 200 Volt/50 Hertz/1 Phase; No capacitor P Drive Motor , Volt/60 Hertz/1 Phase Drive Motor Volt/50 Hertz/1 Phase; No capacitor Drive Motor 380 Volt/50 Hertz/3 Phase; No capacitor Drive Motor Volt/50 Hertz/3 Phase; No capacitor P Drive Motor Volt/60 Hertz/3 Phase; No capacitor Motor Capacitor Start; For Drive Motor on 20 Amp models Motor Capacitor Run; For Drive Motor on 20 Amp models Motor Pulley 60 Hertz Motor Pulley 50 Hertz Bolt Screw Drive Access Cover Nut 4 required 12 M Screw Motor Mount Bracket 14 M Nut 15 M4853P3 Belt Tension Tool Kit Motor Channel Nut Idler Bracket Washer Drum Idler Spring With silencer Washer 22 M Screw Screw P Idler Wheel Assembly Cylinder Idler Arm Nut Double Ended Stud

66 Blower Components TMB2919P_

67 Blower Components REF PART NO. DESCRIPTION COMMENTS Lower Rear Panel Screw Exhaust Thimble 8 inches 4 M Screw Drive Access Cover Motor Drip Pan Motor Conduit Mounting Bracket Screw 2 required Motor Capacitor Start; For P Blower Motor and Blower Motor Motor Capacitor Run; For P Blower Motor and Blower Motor Key P Blower Motor Volt/60 Hertz/1 Phase Blower Motor 100 or 200, Volt/50 Hertz/1 Phase P Blower Motor , 240 Volt/60 Hertz/3 Phase; No capacitor Blower Motor Mounting Plate Screw 14 M Washer P Blower Assembly 16 M Nut 17 M Nut Fan Motor Harness Assembly Models through 2/28/10; 3 Phase except electric models with 240 Volt and below Fan Motor Harness Assembly Models starting 3/1/10; 3 Phase except electric models with 240 Volt and below Fan Motor Harness Assembly Models through 2/28/10; 1 Phase; 3 Phase electric models with 240 Volt and below Fan Motor Harness Assembly Models starting 3/1/10; 1 Phase; 3 Phase electric models with 240 Volt and below Damper and Hinge Exhaust Assembly 21 N/A Damper Spacer 22 M Thermistor 23 M Limit Thermostat P Gasket For blower housing opening N/A = Part no longer available

68 Moisture Sensing Components TMB3147P_

69 Moisture Sensing Components REF PART NO. DESCRIPTION COMMENTS 1 M Nut Slip Ring Holder Slip Ring Assembly Moisture Sensor Harness Assembly

70 Rotation Sensor C, D and I models TMB2384P_

71 Rotation Sensor REF PART NO. DESCRIPTION COMMENTS P Rotation Sensor Rotation Sensor Cable Assembly With receptacle Rotation Sensor Bracket Bearing Housing Bracket Rotation Sensor Cover Screw

72 Airflow Switch TMB3126P_

73 Airflow Switch REF PART NO. DESCRIPTION COMMENTS Airflow Switch Cover Non-moisture sensing Airflow Switch Cover Moisture sensing Airflow Switch Wrapper Switch Airflow Switch Arm Screw Switch Bracket Airflow Switch and Arm Bracket Airflow Switch Vane

74 Gas Burner Housing and Secondary Stove Limit TMB2642P_

75 Gas Burner Housing and Secondary Stove Limit REF PART NO. DESCRIPTION COMMENTS Screw 2 M Limit Thermostat Rear Valve Cover Pipe Clip P Spark Electrode Screw Igniter Cover Stove Limit Harness 9 M Screw 2 required P Gas Burner 11 M Thermostat Cover Limit Thermostat Secondary Burner Grill Stove Top and Sides Stove Back

76 Gas Valve Assembly - Non-CE and Non-Australian Gas Models TMB3131P_

77 Gas Valve Assembly - Non-CE and Non-Australian Gas Models REF PART NO. DESCRIPTION COMMENTS NA M4924P3 L.P. Conversion Kit 0-2,000 feet; 90,000 Btu input NA High Voltage Lead Primary Air Adjustment Sleeve 2 M Burner Orifice Liquid Petroleum Gas (L.P.); Drill no. 31 (3.0 mm); 0-2,000 feet 2 N/A Burner Orifice L.P.; Drill no. 32 (2.9 mm); 2,001-4,000 feet 2 M Burner Orifice L.P.; Drill no. 33 (2.9 mm); 4,001-6,000 feet; 60 Hertz; Models HT055D and ST055D 2 M Burner Orifice L.P.; Drill no. 35 (2.8 mm); 6,001-8,000 feet 2 M Burner Orifice L.P.; Drill no. 36 (2.7 mm); 8,001-10,000 feet Burner Orifice L.P.; Drill no. 7/64 (2.8 mm); 50 Hertz; Models HT055D and ST055D 2 M Burner Orifice Natural Gas (N.G.); Drill no. 8 (5.1 mm); 0-2,000 feet 2 M Burner Orifice N.G.; Drill no. 10 (4.9 mm); 2,001-4,000 feet 2 M Burner Orifice N.G.; Drill no. 12 (4.8 mm); 4,001-6,000 feet 2 M Burner Orifice N.G.; Drill no. 14 (4.6 mm); 6,001-8,000 feet 2 M Burner Orifice N.G.; Drill no. 16 (4.5 mm); 8,001-10,000 feet Orifice Holder Bracket Orifice Keeper Bracket Orifice Adapter Screw 10 required Pop Rivet 8 M Snap Bushing Rear Valve Cover P Gas Valve N.G P Gas Valve L.P. 11 H Street Elbow Valve Support Bracket Forward Valve Cover 14 M Harness Assembly Screw 2 required N/A = Part no longer available

78 Gas Valve and Piping - CE and Australian Gas Models TMB3049P_

79 Gas Valve and Piping - CE and Australian Gas Models REF PART NO. DESCRIPTION COMMENTS 1 M412562P Gas Shut-Off Valve Models through 1/31/ Pipe Nipple 1/2 NPT; Models through 1/31/10 3 H Union Models through 1/31/ Pipe Nipple Elbow Adapter BPT/NPT Screw Screw Gas Valve Bracket Primary Air Adjustment Sleeve Screw Spud Adapter O-Ring P N.G. Valve Regulated P L.P. Valve Unregulated Gas Valve Coil 24 Volt NOTE: For CE gas and orifice information, refer to Installation Manual

80 Electric Heater Components TMB3148P_

81 Electric Heater Components REF PART NO. DESCRIPTION COMMENTS Stove Connectors Cover Screw 3 M Limit Thermostat Nut Jumper Bar 2 required for 380, 400, and Volt 5 M Jumper Strip 3 required for Volt models; 6 required for all other models Stove Grill Stove Partition P Heater Element 3 required; 208 Volt/1 or 3 Phase, 8 kw heater element for Volt models P Heater Element 3 required; 220 Volt/1 or 3 Phase, 8 kw heater element for 380 Volt models P Heater Element 3 required; 240 Volt/1 or 3 Phase and Volt/3 Phase, 8 kw heater element for , and Volt models Stove Limit Bypass Harness Jumper Wire 1 required for Volt P Cable Set Heater Assembly H1-H P Cable Set Heater Assembly H4-H6; 240 Volt or less

82 Control Tray Harnesses for Gas Models TMB2798P_

83 Control Tray Harnesses for Gas Models REF PART NO. DESCRIPTION COMMENTS NA High Voltage Lead Junction Box Harness Ignition Control Harness CE and Australian models Ignition Control Harness All other models P Power Harness CE and Australian models through 2/28/10; 3 Phase models with less than 380 Volts P Power Harness Models through 2/28/10; Contactor; 1 Phase Power Harness Models through 2/28/10; 3 Phase models with 380 Volts or higher Power Harness CE and Australian models starting 3/1/10; 3 Phase models with less than 380 Volts Power Harness Models starting 3/1/10; Contactor; 1 Phase Power Harness Models starting 3/1/10; 3 Phase models with 380 Volts or higher Jumper Disconnect Assembly CE and Australian models Motor Contactor Harness Models through 2/28/10; 3 Phase P Motor Contactor Harness Models starting 3/1/10; 3 Phase 6 M Jumper Harness Assembly 100 Volt 6 M Jumper Harness Assembly 120 Volt 6 M Jumper Harness Assembly 208 Volt 6 M Jumper Configuration Assembly 240 Volt 6 M Jumper Harness Assembly 380 Volt 6 M Jumper Configuration Assembly 480 Volt 7 M Network Capacitor Assembly 3O, 3V, 3X, DO, DV, DX and OM control suffixes 8 M Capacitor Network Harness Assembly 3O, 3V, 3X, DO, DV, DX and OM control suffixes Gas Disconnect Harness CE and Australian models through 2/28/ Gas Disconnect Harness CE and Australian models starting 3/1/

84 Control Tray for Non-CE and Non-Australian Gas Models For 1 Phase and Volt / 3 Phase Models For Volt / 3 Phase Models TMB2541P_

85 Control Tray for Non-CE and Non-Australian Gas Models REF PART NO. DESCRIPTION COMMENTS NA Expansion Clip 4 required; Used on item 14 NA M Secure Ground Label NA Warning Label Extended tumble; On control tray cover Terminal Block Shield Terminal Block 3 M Insulator Screw 3 required P Ignition Control Screw Bumper Pad 2 required Screw 2 required Control Tray Screw 3 required Wire Clip 12 M Screw 4 required Wire Clip 2 required 14 M414312P Transformer 120 Volt; Dual secondary 14 M414230P Transformer 120 Volt; Primary/secondary 14 M414228P Transformer Volt 14 M414229P Transformer Volt 15 M Screw 4 required P Contactor Fuse Bracket Volt; Models through 2/28/ Fuse Bracket Volt; Models starting 3/1/ P Fuse Holder Body Includes nuts; 3 required for 1 Phase; 4 required for 3 Phase Fuse 3.5 Amp Fuse 1.25 Amp Fuse Holder Cap 3 required for 1 Phase and Volt/3 Phase; 4 required for Volt/3 Phase 22 M413544P Fuse Holder Includes nuts; 2 required for Volt; Models through 2/28/ Fuse Holder 2 required for Volt; Models starting 3/1/10 23 M Fuse 2 required for Volt; 0.5 Amp Fuse 2 Amp; Volt Fuse Bracket Volt

86 Control Tray Components for CE and Australian Gas Models For 1 Phase and Volt / 3 Phase Models For Volt / 3 Phase Models TMB2542P_

87 Control Tray Components for CE and Australian Gas Models REF PART NO. DESCRIPTION COMMENTS NA Expansion Clip 4 required NA M Secure Ground Label NA Screw 2 required NA Screw 4 required for item 19 NA ICM Reset Label NA M Earth Terminal Sticker NA Warning Label Extended tumble; On control tray cover Screw 3 required P Ignition Control 24 Volt Screw Bumper Pad 2 required Screw 2 required Control Tray Wire Clip 8 M Screw Wire Clip 2 required 10 M414229P Transformer Volt 10 M414228P Transformer Volt 11 M Screw 4 required P Contactor Fuse Bracket Volt; Models through 2/28/ Fuse Bracket Volt; Models starting 3/1/10 14 M Pushbutton Switch P Fuse Holder Body Includes nuts; 3 required for 1 Phase; 4 required for 3 Phase models with less than 380 Volts; 2 required for 3 Phase models with 380 Volts or higher Fuse 3.5 Amp Fuse 1.25 Amp Fuse Holder Cap 3 required for 1 Phase; 4 required for 3 Phase models with less than 380 Volts; 2 required for 3 Phase models with 380 Volts or higher 19 M413544P Fuse Holder Includes nuts; 2 required for Volt; Models through 2/28/ Fuse Holder 2 required for Volt; Models starting 3/1/10 20 M Fuse 2 required for Volt; 0.5 Amp Fuse 1 required for 1 Phase; 2 required for 3 Phase; 2 Amp Fuse Bracket Volt Terminal Block Shield Terminal Block 25 M Insulator Screw P Extension Handle Models through 7/31/11 28 M412187P Mounting Switch Base Models through 7/31/11 29 M Finger Guard Models through 7/31/

88 Control Tray Harnesses for Electric Models TMB2800P_