Commercial Dryers. Parts. Metered and Nonmetered. Refer to Page 3 for Model Numbers. DRY721C_515202

Transcription

1 Commercial Dryers Metered and Nonmetered Refer to Page 3 for Model Numbers Parts DRY721C_ Part No R1 April 2015

2

3 Table of Contents Title Page Parts Ordering Information... 2 Serial Plate Location... 2 Model Identification... 3 Control Panel and Controls - Coin Drop and Card Models... 4 Control Cabinet Controls - Coin Drop Models... 6 Non-Electronic Coin Drop... 8 Electronic Coin Drop Integrated Card Reader Installed and Ready Models Cabinet Top Loading Door without Window Loading Door with Window Access Panel, Front Panel and Seal Motor, Exhaust Fan and Belt Front Bulkhead, Air Duct and Felt Seal Cylinder Assembly without Light Front Bulkhead, Air Duct, Felt Seal and Cylinder with Light Rear Bulkhead, Felt Seal, Cylinder Roller and Terminal Block Heater Duct and Element Assembly - Electric Model Dryers Heater Duct Assembly - Gas Model Dryers Gas Valve, Igniter and Gas Conversion Kits Burner Orifice Spuds - For Higher Elevations Cabinet, Exhaust Duct and Base Power Cord Terminal Block and Terminals (Drawing 1 of 2) Terminal Block and Terminals (Drawing 2 of 2) Terminals and Terminal Extractor Tools Wire Harnesses and Wires Parts Index Copyright 2015, Alliance Laundry Systems LLC All rights reserved. No part of the contents of this book may be reproduced or transmitted in any form or by any means without the expressed written consent of the publisher

4 If literature or replacement parts are required, contact the source from whom the machine was purchased or contact Alliance Laundry Systems at (920) for the name and address of the nearest authorized parts distributor. Parts Ordering Information For technical assistance, call either of the numbers listed below: (920) Ripon, Wisconsin Wevelgem, Belgium When calling or writing about your product, be sure to mention model and serial numbers. Model and serial numbers are located on serial plate(s) as shown. Serial Plate Location Serial Plate DRY2283P_

5 Model Identification Information in this manual is applicable to these dryer models: BDEBCAGS171TN01 BDEBCAGS171TW01 BDEBXAGS171TW01 BDGBCAGS111TN01 BDGBCAGS111TW01 BDGBXAGS111TW01 HDEBCAGS171TW01 HDGBCAGS111TW01 KDEBCASW171TN01 KDEBGASW171TN01 KDGBCASW111TN01 KDGBGASW111TN01 SDEBCAGS171TQ01 SDEBCAGS171TW01 SDEBXAGS171TW01 SDEBYAGS171TW01 SDGBCAGS111TQ01 SDGBCAGS111TW01 SDGBXAGS111TW01 SDGBYAGS111TW

6 Control Panel and Controls - Coin Drop and Card Models DRY2325P_

7 Control Panel and Controls - Coin Drop and Card Models REF PART NO. DESCRIPTION COMMENTS Switch Screw P Transformer Some models may have jumper wire attached to transformer. Discard jumper wire when replacing transformer; Models BDEBXAGS171TW01, BDGBXAGS111TW01, KDEBGASW171TN01, KDGBGASW111TN01, SDEBXAGS171TW01, SDEBYAGS171TW01, SDGBXAGS111TW01 and SDGBYAGS111TW P Transformer All other models Resistor Diagnostic Wire Harness Assembly Models KDEBGASW171TN01, KDGBGASW111TN01, SDEBYAGS171TW01 and SDGBYAGS111TW Central Pay Harness From MDC control to customer supplied pay unit Control Assembly Models BDEBCAGS171TN01, BDEBCAGS171TW01, BDEBXAGS171TW01, BDGBCAGS111TN01, BDGBCAGS111TW01 and BDGBXAGS111TW P Control Assembly All other models G Control Panel Assembly Gray; Models KDEBGASW171TN01 and KDGBGASW111TN Control Panel Assembly Gray; Models KDEBCASW171TN01 and KDGBCASW111TN Q Control Panel and Bracket Assembly Bisque; Models SDEBCAGS171TQ01 and SDGBCAGS111TQ W Control Panel and Bracket Assembly White; Models BDEBCAGS171TW01, BDEBXAGS171TW01, BDGBCAGS111TW01, BDGBXAGS111TW01, HDEBCAGS171TW01, HDGBCAGS111TW01, SDEBCAGS171TW01, SDEBXAGS171TW01, SDEBYAGS171TW01, SDGBCAGS111TW01, SDGBXAGS111TW01 and SDGBYAGS111TW B Control Panel and Bracket Assembly Black; Models BDEBCAGS171TN01 and BDGBCAGS111TN Graphic Overlay Models SDEBCAGS171TQ01, SDEBCAGS171TW01, SDEBXAGS171TW01, SDEBYAGS171TW01, SDGBCAGS111TQ01, SDGBCAGS111TW01, SDGBXAGS111TW01 and SDGBYAGS111TW Graphic Overlay Models KDEBCASW171TN01, KDEBGASW171TN01, KDGBCASW111TN01 and KDGBGASW111TN Graphic Overlay Models BDEBCAGS171TN01, BDEBCAGS171TW01, BDEBXAGS171TW01, BDGBCAGS111TN01, BDGBCAGS111TW01 and BDGBXAGS111TW Graphic Overlay Models HDEBCAGS171TW01 and HDGBCAGS111TW Screw Key P Lock Kit Includes item Lock Cam Audit Switch Bracket

8 Control Cabinet Controls - Coin Drop Models Coin Models DRY2326P_

9 Control Cabinet Controls - Coin Drop Models REF PART NO. DESCRIPTION COMMENTS NA Nut Use with item 9; 2 required; Models BDEBCAGS171TN01, BDEBCAGS171TW01, BDGBCAGS111TN01, BDGBCAGS111TW01, HDEBCAGS171TW01, HDGBCAGS111TW01, SDEBCAGS171TQ01, SDEBCAGS171TW01, SDGBCAGS111TQ01 and SDGBCAGS111TW Meter Case Assembly Gray; Models KDEBCASW171TN01 and KDGBCASW111TN W Meter Case Assembly White; Models BDEBCAGS171TW01, BDEBXAGS171TW01, BDGBCAGS111TW01, BDGBXAGS111TW01, HDEBCAGS171TW01, HDGBCAGS111TW01, SDEBCAGS171TW01, SDEBXAGS171TW01, SDGBCAGS111TW01 and SDGBXAGS111TW Q Meter Case Assembly Bisque; Models SDEBCAGS171TQ01 and SDGBCAGS111TQ B Meter Case Assembly Black; Models BDEBCAGS171TN01 and BDGBCAGS111TN Security Wrapper Assembly Gray; Models KDEBCASW171TN01 and KDGBCASW111TN W Wrapper Assembly White; Models BDEBCAGS171TW01, BDEBXAGS171TW01, BDGBCAGS111TW01, BDGBXAGS111TW01, HDEBCAGS171TW01, HDGBCAGS111TW01, SDEBCAGS171TW01, SDEBXAGS171TW01, SDGBCAGS111TW01 and SDGBXAGS111TW Q Security Wrapper Assembly Bisque; Models SDEBCAGS171TQ01 and SDGBCAGS111TQ B Wrapper Assembly Black; Models BDEBCAGS171TN01 and BDGBCAGS111TN Screw 6 required Rear Access Panel Expansion Clip 6 required Control Panel Gray; Models KDEBCASW171TN01 and KDGBCASW111TN WP Control Panel White; Models BDEBCAGS171TW01, BDEBXAGS171TW01, BDGBCAGS111TW01, BDGBXAGS111TW01, HDEBCAGS171TW01, HDGBCAGS111TW01, SDEBCAGS171TW01, SDEBXAGS171TW01, SDGBCAGS111TW01 and SDGBXAGS111TW Q Control Panel Bisque; Models SDEBCAGS171TQ01 and SDGBCAGS111TQ BP Control Panel Black; Models BDEBCAGS171TN01 and BDGBCAGS111TN01 7 M Screw Models BDEBCAGS171TN01, BDGBCAGS111TN01, KDEBCASW171TN01 and KDGBCASW111TN Screw All other models Operating Instruction Label Models KDEBCASW171TN01 and KDGBCASW111TN Operating Instructions Label All other models Bolt 2 required; Models BDEBCAGS171TN01, BDEBCAGS171TW01, BDGBCAGS111TN01, BDGBCAGS111TW01, HDEBCAGS171TW01, HDGBCAGS111TW01, SDEBCAGS171TQ01, SDEBCAGS171TW01, SDGBCAGS111TQ01 and SDGBCAGS111TW Single Overlay Models BDEBCAGS171TN01, BDEBCAGS171TW01, BDGBCAGS111TN01, BDGBCAGS111TW01, HDEBCAGS171TW01, HDGBCAGS111TW01, SDEBCAGS171TQ01, SDEBCAGS171TW01, SDGBCAGS111TQ01 and SDGBCAGS111TW Single Overlay Models KDEBCASW171TN01 and KDGBCASW111TN Switch

10 Non-Electronic Coin Drop Coin Models DRY2327P_

11 Non-Electronic Coin Drop REF PART NO. DESCRIPTION COMMENTS P Coin Drop Assembly Token; mzp;.880 diameter x.079 thick; Brass Coin Drop Assembly Token; mzp;.990 diameter x.081 thick; Silver P Coin Drop U.S.; $ P Coin Drop Token; not available; Replacement for 38963P Coin Drop only P Harness Assembly Models BDEBCAGS171TN01, BDEBCAGS171TW01, BDGBCAGS111TN01, BDGBCAGS111TW01, HDEBCAGS171TW01, HDGBCAGS111TW01, KDEBCASW171TN01, KDGBCASW111TN01, SDEBCAGS171TQ01, SDEBCAGS171TW01, SDGBCAGS111TQ01 and SDGBCAGS111TW Harness Assembly All other models Nut P Wire Guard Anti-stringing security device; Add to coin drops

12 Electronic Coin Drop Coin Models DRY2328P_

13 Electronic Coin Drop REF PART NO. DESCRIPTION COMMENTS Coin Identification Paper 2 CK115 Electronic Coin Drop Kit Includes items 1, 3, 5 and 7; United States and Canada coins Coin Drop Wire Harness Harness Assembly Electronic coin drop requires this harness. If unit is not factory-equipped with this harness, it must be ordered separately Nut Hexnut; Used with front assemblies without guide rods 6 CK096 Mounting Tool Kit Clip P Transformer Electronic coin drop requires this transformer. If unit is not factory-equipped with this transformer, it must be ordered separately

14 Integrated Card Reader Installed and Ready Models Models KDEBGASW171TN01, KDGBGASW111TN01, SDEBYAGS171TW01 and SDGBYAGS111TW01 DRY2329P_

15 Integrated Card Reader Installed and Ready Models REF PART NO. DESCRIPTION COMMENTS Card Insert Overlay Models SDEBYAGS171TW01 and SDGBYAGS111TW Blank Black Label Models KDEBGASW171TN01 and KDGBGASW111TN Control Panel Gray; Models KDEBGASW171TN01 and KDGBGASW111TN W Security Cabinet Assembly White; Models SDEBYAGS171TW01 and SDGBYAGS111TW Security Wrapper Assembly Gray; Models KDEBGASW171TN01 and KDGBGASW111TN W Wrapper Assembly White; Models SDEBYAGS171TW01 and SDGBYAGS111TW Screw 6 required; Model SDEBYAGS171TW Rear Access Panel Expansion Clip 6 required; Model SDEBYAGS171TW01 7 M Screw Use with stainless steel side panels Screw Use with painted side panels Operating Instruction Label Models KDEBGASW171TN01 and KDGBGASW111TN Operating Instructions Label Models SDEBYAGS171TW01 and SDGBYAGS111TW

16 Cabinet Top DRY2331P_

17 Cabinet Top REF PART NO. DESCRIPTION COMMENTS Nut Top Panel Stainless steel; Models BDEBCAGS171TN01, BDGBCAGS111TN01, KDEBCASW171TN01, KDEBGASW171TN01, KDGBCASW111TN01 and KDGBGASW111TN WP Top Panel White; Includes item 4; All other models Bolt Top Mounting Bracket Screw

18 Loading Door without Window All Models Except KDEBCASW171TN01, KDEBGASW171TN01, KDGBCASW111TN01 and KDGBGASW111TN01 DRY1857P_

19 Loading Door without Window REF PART NO. DESCRIPTION COMMENTS Door Strike Mount Door Strike P Liner Door Seal P Liner, Seal and Grill Assembly Electric models WP Liner, Seal and Grill Assembly White; Gas models Screw Hinge WP Dryer Door White QP Dryer Door Bisque Dryer Door Stainless steel; Includes item WP Door Pull and Wedge Kit White; Includes item QP Door Pull and Wedge Kit Bisque; Includes item Door Pull Light gray Door Handle Wedge

20 Loading Door with Window Models KDEBCASW171TN01, KDEBGASW171TN01, KDGBCASW111TN01 and KDGBGASW111TN01 DRY2291P_

21 Loading Door with Window REF PART NO. DESCRIPTION COMMENTS Dryer Door Models KDGBCASW111TN01 and KDGBGASW111TN Dryer Door Assembly Models KDEBCASW171TN01 and KDEBGASW171TN Washer Screw P Dryer Door Window Door Strike Mount Door Strike Screw P Liner Door Seal DG Liner, Seal and Grill Assembly Screw Hinge Screw Window Clip Models KDEBCASW171TN01 and KDEBGASW171TN Nut Models KDEBCASW171TN01 and KDEBGASW171TN Window Trim Models KDGBCASW111TN01 and KDGBGASW111TN Window Trim Models KDEBCASW171TN01 and KDEBGASW171TN Glass Door Window Models KDEBCASW171TN01 and KDEBGASW171TN P Door Pull Kit Includes items 2 and

22 Access Panel, Front Panel and Seal DRY1824P_

23 Access Panel, Front Panel and Seal REF PART NO. DESCRIPTION COMMENTS Speed Clip 1 per side Switch Front Panel Seal Front Panel Stainless steel; Models BDEBCAGS171TN01, BDGBCAGS111TN01, KDEBCASW171TN01, KDEBGASW171TN01, KDGBCASW111TN01 and KDGBGASW111TN WP Front Panel White; Models BDEBCAGS171TW01, BDEBXAGS171TW01, BDGBCAGS111TW01, BDGBXAGS111TW01, HDEBCAGS171TW01, HDGBCAGS111TW01, SDEBCAGS171TW01, SDEBXAGS171TW01, SDEBYAGS171TW01, SDGBCAGS111TW01, SDGBXAGS111TW01 and SDGBYAGS111TW QP Front Panel Bisque; Models SDEBCAGS171TQ01 and SDGBCAGS111TQ01 5 M Screw Use with stainless steel side panels Screw Use with painted side panels Access Panel Assembly Stainless steel; Models BDGBCAGS111TN01, KDGBCASW111TN01 and KDGBGASW111TN Access Panel and Guard Assembly W Access Panel and Guard Assembly Stainless steel; Models BDEBCAGS171TN01, KDEBCASW171TN01 and KDEBGASW171TN01 White; Models BDEBCAGS171TW01, BDEBXAGS171TW01, HDEBCAGS171TW01, SDEBCAGS171TW01, SDEBXAGS171TW01 and SDEBYAGS171TW Q Access Panel and Guard Bisque; Model SDEBCAGS171TQ01 Assembly WP Access Panel Assembly White; Models BDGBCAGS111TW01, BDGBXAGS111TW01, HDGBCAGS111TW01, SDGBCAGS111TW01, SDGBXAGS111TW01 and SDGBYAGS111TW Q Access Panel Assembly Bisque; Model SDGBCAGS111TQ Screw Slotted hex head Screw Torx head; Optional for added security Panel Locator 1 per side Screw 1 per side Door Catch Assembly Warning/Caution Label Hinge Hole Plug

24 Motor, Exhaust Fan and Belt DRY2084P_

25 Motor, Exhaust Fan and Belt REF PART NO. DESCRIPTION COMMENTS NA 27604P Anti-Seize Compound Apply to motor shaft when installing blower fan assembly P Blower Housing Seal Screw WP Blower Housing Includes items 1 and P Motor and Pulley Assembly 120 Volt/60 Hertz; Apply anti-seize compound to motor shaft when installing blower fan assembly; Includes items Motor Mount Clamp P Cylinder Belt Motor Pulley 60 Hertz 8 590P3 Motor Hub Ring Kit Screw P Blower Fan Assembly Apply anti-seize compound to motor shaft when installing blower fan assembly Idler Spring Nut Idler Lever P Shaft Washer P Idler Wheel and Bearing Assembly Retaining Ring Screw Idler Lever and Wheel Assembly Includes items Nut Motor Mount Thermistor Assembly Black Screw P Blower and Fan Kit Includes items 1-5 and

26 Front Bulkhead, Air Duct and Felt Seal All Models Except KDEBCASW171TN01, KDEBGASW171TN01, KDGBCASW111TN01 and KDGBGASW111TN01 DRY2221P_

27 Front Bulkhead, Air Duct and Felt Seal REF PART NO. DESCRIPTION COMMENTS P Front Bulkhead Assembly Unpainted; Includes items 2 and P Cylinder Seal Assembly P Adhesive Apply to cylinder seal 2 RB Seal Kit Includes 2 cylinder seals, P Blower Housing Seal and P Adhesive Screw 1 per side 4 M Screw Use with stainless steel side panels Screw Use with painted side panels LG Lint Filter Gray; Models BDEBCAGS171TN01, BDEBCAGS171TW01, BDEBXAGS171TW01, HDEBCAGS171TW01, SDEBCAGS171TQ01, SDEBCAGS171TW01, SDEBXAGS171TW01 and SDEBYAGS171TW W Lint Filter White; Models BDGBCAGS111TN01, BDGBCAGS111TW01, BDGBXAGS111TW01, HDGBCAGS111TW01, SDGBCAGS111TQ01, SDGBCAGS111TW01, SDGBXAGS111TW01 and SDGBYAGS111TW LG Air Duct Assembly Gray; Models BDEBCAGS171TN01, BDEBCAGS171TW01, BDEBXAGS171TW01, HDEBCAGS171TW01, SDEBCAGS171TQ01, SDEBCAGS171TW01, SDEBXAGS171TW01 and SDEBYAGS171TW W Air Duct Assembly White; Models BDGBCAGS111TN01, BDGBCAGS111TW01, BDGBXAGS111TW01, HDGBCAGS111TW01, SDGBCAGS111TQ01, SDGBCAGS111TW01, SDGBXAGS111TW01 and SDGBYAGS111TW Screw Felt Pad 1 per side Cylinder Glide 1 per side 10 RB Glide Kit Includes items 8 and Cylinder Glide Bracket 1 per side Screw 2 per side

28 Cylinder Assembly without Light All Models Except KDEBCASW171TN01, KDEBGASW171TN01, KDGBCASW111TN01 and KDGBGASW111TN01 DRY2221PA_

29 Cylinder Assembly without Light REF PART NO. DESCRIPTION COMMENTS LG Cylinder Baffle Gray; Models BDEBCAGS171TN01, BDEBCAGS171TW01, BDEBXAGS171TW01, HDEBCAGS171TW01, SDEBCAGS171TQ01, SDEBCAGS171TW01, SDEBXAGS171TW01 and SDEBYAGS171TW W Cylinder Baffle White; Models BDGBCAGS111TN01, BDGBCAGS111TW01, BDGBXAGS111TW01, HDGBCAGS111TW01, SDGBCAGS111TQ01, SDGBCAGS111TW01, SDGBXAGS111TW01 and SDGBYAGS111TW LGP Cylinder Assembly Galvanized; Includes 3 of item 1 and 6 of item 3; Models BDEBCAGS171TN01, BDEBCAGS171TW01, BDEBXAGS171TW01, HDEBCAGS171TW01, SDEBCAGS171TQ01, SDEBCAGS171TW01, SDEBXAGS171TW01 and SDEBYAGS171TW WP Cylinder Assembly Galvanized; Includes 3 of item 1 and 6 of item 3; Models BDGBCAGS111TN01, BDGBCAGS111TW01, BDGBXAGS111TW01, HDGBCAGS111TW01, SDGBCAGS111TQ01, SDGBCAGS111TW01, SDGBXAGS111TW01 and SDGBYAGS111TW Screw

30 Front Bulkhead, Air Duct, Felt Seal and Cylinder with Light Models KDEBCASW171TN01, KDEBGASW171TN01, KDGBCASW111TN01 and KDGBGASW111TN01 DRY2136P_

31 Front Bulkhead, Air Duct, Felt Seal and Cylinder with Light REF PART NO. DESCRIPTION COMMENTS Cylinder Light Lens Drum Light Lamp Light Housing Assembly Includes item Front Bulkhead Assembly Galvanized; Includes item P Cylinder Seal Assembly P Adhesive Apply to cylinder seal 5 RB Seal Kit Includes 2 cylinder seals, P Blower Housing Seal and P Adhesive DG Cylinder Baffle DG Cylinder Assembly Galvanized; Includes (3) of item 6 and (6) of item Screw 9 M Screw Use with stainless steel side panels Screw Use with painted side panels DG Air Duct Assembly DG Lint Filter Cylinder Glide Felt Pad Screw Cylinder Glide Bracket Screw Screw 18 RB Glide Kit Includes items 12 and

32 Rear Bulkhead, Felt Seal, Cylinder Roller and Terminal Block DRY1774P_

33 Rear Bulkhead, Felt Seal, Cylinder Roller and Terminal Block REF PART NO. DESCRIPTION COMMENTS P Cylinder Seal Assembly P Adhesive Apply to cylinder seal 1 RB Seal Kit Includes 2 cylinder seals, P Blower Housing Seal and P Adhesive 2 M Screw Models BDEBCAGS171TN01, BDGBCAGS111TN01, KDEBCASW171TN01, KDEBGASW171TN01, KDGBCASW111TN01 and KDGBGASW111TN Screw All other models Rear Bulkhead Polished; Models KDEBCASW171TN01, KDEBGASW171TN01, KDGBCASW111TN01 and KDGBGASW111TN P Rear Bulkhead Assembly Galvanized; Includes item 1; All other models Screw Electric models Terminal Block Shield Electric models P Terminal Block Assembly Includes 3 of item 7; Electric models Screw Nut Screw Washer Cylinder Roller Bracket P Cylinder Roller Retaining Ring Washer Washer P Shaft Nut 18 RB Roller Kit Includes item

34 Heater Duct and Element Assembly - Electric Model Dryers DRY1789P_

35 Heater Duct and Element Assembly - Electric Model Dryers REF PART NO. DESCRIPTION COMMENTS Screw Outlet Cover P Heater Duct and Screw Assembly Includes items 1 and Wire Assembly Orange; Thermostat jumper; Attaches to heater assembly Wire Assembly Black; Fuse jumper; Attaches to heater assembly Thermal Fuse Assembly Screw Limit Thermostat P Heater Assembly 5.35 kw; 240 Volt Heater Kit Assembly 4.75 kw; 208 Volt P3 Heater Kit 5.35 kw; 240 Volt

36 Heater Duct Assembly - Gas Model Dryers D405P_

37 Heater Duct Assembly - Gas Model Dryers REF PART NO. DESCRIPTION COMMENTS Screw Heat Duct Shroud Outlet Cover P Heater Duct and Screw Assembly Includes items 1 and Combustion Duct Screw Limit Thermostat Black; Auto reset Thermostat

38 Gas Valve, Igniter and Gas Conversion Kits Gas Models DRY2062P_

39 Gas Valve, Igniter and Gas Conversion Kits REF PART NO. DESCRIPTION COMMENTS Lead-In Pipe Assembly Screw P Igniter and Bracket Assembly Screw Sensor Screw P Burner Assembly 8 458P3 L.P. Conversion Kit Used to convert dryers from Natural Gas (N.G.) or Mixed Gas to Liquid Petroleum Gas (L.P.) for 25,000 Btu 9 459P3 N.G. Conversion Kit Used to convert dryers from L.P. to N.G. or Mixed Gas for 25,000 Btu B Secondary Coil P Gas Valve Assembly 25,000 Btu; Includes items 10 and Screw Gas Valve Mounting Bracket A Booster and Holding Coil Elbow Shut-Off Valve

40 Burner Orifice Spuds - For Higher Elevations Gas Models DRY2266P_

41 Burner Orifice Spuds - For Higher Elevations REF PART NO. DESCRIPTION COMMENTS L.P. Orifice Liquid Petroleum Gas (L.P.); feet ( m) L.P. Orifice L.P.; feet (3355 m) and higher N.G. Orifice Natural Gas (N.G.); feet ( m) N.G. Orifice N.G.; feet ( m) N.G. Orifice N.G.; feet ( m) Screw Orifice N.G.; feet ( m) N.G. Orifice N.G.; feet ( m) N.G. Orifice N.G.; feet (3200 m) and higher

42 Cabinet, Exhaust Duct and Base DRY2324P_

43 Cabinet, Exhaust Duct and Base REF PART NO. DESCRIPTION COMMENTS Panel Locator Screw Use with stainless steel panels Screw Use with painted panels Bumper Pad Frame Gusset Top Hinge Screw P Cabinet Rear Panel Gas Clearance Label Gas models Venting Instruction Label Damper Use when connecting to a manifold vent system P3 Flexible Venting Kit Access Panel Plate Electric Clearance Label Electric models Exhaust Duct Each dryer requires 2 pieces GP Cabinet Side Panel Gray; Right Cabinet Side Panel Stainless steel; Right; Models KDEBCASW171TN01, KDEBGASW171TN01, KDGBCASW111TN01 and KDGBGASW111TN QP Cabinet Side Panel Bisque; Right; Models SDEBCAGS171TQ01 and SDGBCAGS111TQ Cabinet Side Panel Stainless steel; Right; All other models WP Cabinet Side Panel White; Right; All other models P3 Directional Exhaust Kit Used to vent dryer out the sides or bottom P3 Hold Down Kit For mobile home installations Dryer Base Leveling Leg Rubber Foot GP Cabinet Side Panel Gray; Left Cabinet Side Panel Stainless steel; Left; Models KDEBCASW171TN01, KDEBGASW171TN01, KDGBCASW111TN01 and KDGBGASW111TN QP Cabinet Side Panel Bisque; Left; Models SDEBCAGS171TQ01 and SDGBCAGS111TQ Cabinet Side Panel Stainless steel; Left; All other models WP Cabinet Side Panel White; Left; All other models

44 Power Cord DRY1879P_

45 Power Cord REF PART NO. DESCRIPTION COMMENTS Screw Models BDEBCAGS171TN01, BDGBCAGS111TN01, KDEBCASW171TN01 and KDGBCASW111TN Screw All other models Strain Relief Gas models Lead-In Cord Gas models

46 Terminal Block and Terminals (Drawing 1 of 2) DRY2038P_

47 Terminal Block and Terminals (Drawing 1 of 2) REF PART NO. DESCRIPTION COMMENTS Wire Clip 11/16 inch Wire Clip 1 inch Insulated Female Spade Terminal (1) 12 gauge wire or (2) 18 gauge wires Female Pin Terminal Circuit Receptacle Plug 3 circuit Male Pin Terminal Circuit Receptacle Circuit Plug Harness Strap Female Pin Terminal 1/8 inch; gauge wire Female Pin Terminal 1/8 inch; gauge wire Circuit Plug Male Pin Terminal 1/8 inch; gauge wire Male Pin Terminal 1/8 inch; gauge wire Circuit Connector Plug Circuit Receptacle

48 Terminal Block and Terminals (Drawing 2 of 2) DRY2338P_

49 Terminal Block and Terminals (Drawing 2 of 2) REF PART NO. DESCRIPTION COMMENTS Grounding Clip Female Spade Terminal 1/8 inch Female Piggyback Terminal Circuit Connector Female Spade Terminal 1/4 inch; (1) 18 gauge wire Female Spade Terminal 1/4 inch; (2) 18 gauge wires or (1) 12 gauge wire Spade Terminal 1/4 inch; (1) 22 gauge wire Female Spade Terminal 3/16 inch; (1) 18 gauge wire;.020 tab Female Spade Terminal 1/4 inch Female Spade Terminal 1/4 inch; (1) 18 gauge wire Receptacle Housing Insulated Female Spade Terminal 1/4 inch Ring Terminal No. 10; (1) 18 gauge wire Female Spade Terminal 1/4 inch; Double connector Male Tab Terminal 1/4 inch; (2) 18 gauge wires or (1) 12 gauge wire Female Tab Terminal 1/4 inch Terminal Insulated Female Flag Terminal Circuit Plug Circuit Plug Circuit Receptacle Circuit Receptacle Circuit Receptacle Circuit Receptacle

50 Terminals and Terminal Extractor Tools DRY2066P_

51 Terminals and Terminal Extractor Tools REF PART NO. DESCRIPTION COMMENTS Position Housing Female Terminal 1/4 inch; (1) 12 gauge wire; Electric models Female Terminal 1/4 inch; (1) or (2) 18 gauge wires Female Terminal For 1 or 2 wire application 4 283P4 Terminal Extractor Tool For use on Molex connectors 5 310P4 Ratchet Extension Tool 1/4 inch; For coin drop installation 6 190P4 Extractor Tool For use on electric dryer terminals 7 128P4 Extractor Tool For use on gas dryer terminals 8 281P4 Torx Bit T15 Tamper Resistant Bit 8 282P4 Torx Bit Use with Screw on access panel; T25 Tamper Resistant Bit 8 292P4 Torx Bit T20 Standard Bit Bit Holder Use with Screw on access panel; 3/8 inch Torx Drive Tool T10 Standard Bit

52 Wire Harnesses and Wires DRY2285P_

53 Wire Harnesses and Wires REF PART NO. DESCRIPTION COMMENTS NA Gauge Wire Black; Order wire by foot; Order terminals and connectors as required NA Gauge Wire Orange; Order wire by foot; Order terminals and connectors as required P Wire Harness Assembly Models BDEBCAGS171TN01, BDEBCAGS171TW01, BDEBXAGS171TW01, BDGBXAGS111TW01, HDEBCAGS171TW01, SDEBCAGS171TQ01, SDEBCAGS171TW01, SDEBXAGS171TW01, SDEBYAGS171TW01, SDGBCAGS111TQ01, SDGBCAGS111TW01, SDGBXAGS111TW01 and SDGBYAGS111TW Gas Harness Models BDGBCAGS111TN01, BDGBCAGS111TW01, BDGBXAGS111TW01, HDGBCAGS111TW01, KDGBCASW111TN01, KDGBGASW111TN01 and SDGBXAGS111TW P Wire Configuration Assembly Models BDEBCAGS171TN01, BDEBCAGS171TW01, BDEBXAGS171TW01, BDGBXAGS111TW01, HDEBCAGS171TW01, HDGBCAGS111TW01, SDEBCAGS171TQ01, SDEBCAGS171TW01, SDEBXAGS171TW01, SDEBYAGS171TW01, SDGBCAGS111TQ01, SDGBCAGS111TW01, SDGBXAGS111TW01 and SDGBYAGS111TW P Wire Configuration Assembly Models BDEBCAGS171TN01, BDEBCAGS171TW01, BDEBXAGS171TW01, BDGBXAGS111TW01, HDEBCAGS171TW01, HDGBCAGS111TW01, SDEBCAGS171TQ01, SDEBCAGS171TW01, SDEBXAGS171TW01, SDEBYAGS171TW01, SDGBCAGS111TQ01, SDGBCAGS111TW01, SDGBXAGS111TW01 and SDGBYAGS111TW Electronic Harness Models BDEBCAGS171TN01, BDEBCAGS171TW01, BDEBXAGS171TW01, BDGBXAGS111TW01, HDEBCAGS171TW01, SDEBCAGS171TQ01, SDEBCAGS171TW01, SDEBXAGS171TW01 and SDEBYAGS171TW Electronic Harness Models BDGBCAGS111TN01, BDGBCAGS111TW01, HDGBCAGS111TW01, SDGBCAGS111TQ01, SDGBCAGS111TW01, SDGBXAGS111TW01 and SDGBYAGS111TW Electronic Harness Models KDEBCASW171TN01 and KDEBGASW171TN Wire Harness Assembly Models KDGBCASW111TN01 and KDGBGASW111TN01 NOTE: Individual wires are not available separately. Order complete harness, or order wire by the foot. When applying terminals to wires, it is recommended that the terminals be soldered to the wires

54 Notes

55 Parts Index A Access Panel and Guard Assembly Q W Access Panel Assembly Q WP Access Panel Plate Adhesive P... 25, 29, 31 Air Duct Assembly DG LG W Anti-Seize Compound 27604P Audit Switch Bracket B Bit Holder Blank Black Label Blower and Fan Kit P Blower Fan Assembly P Blower Housing WP Blower Housing Seal P Bolt , 15 Booster and Holding Coil 58804A Bumper Pad Burner Assembly P C Cabinet Rear Panel P Cabinet Side Panel GP QP WP GP QP WP Card Insert Overlay Central Pay Harness Clip Coin Drop 38963P P...9 Coin Drop Assembly 38462P Coin Drop Wire Harness Coin Identification Paper Combustion Duct Connector, 2 Circuit Connector, 3 Circuit Control Assembly P Control Panel BP Q WP...7 Control Panel and Bracket Assembly B Q W...5 Control Panel Assembly G Cylinder Assembly DG LGP WP...27 Cylinder Baffle DG LG W...27 Cylinder Belt P...23 Cylinder Glide , 29 Cylinder Glide Bracket , 29 Cylinder Light Lens Cylinder Roller P...31 Cylinder Roller Bracket N/A items do not appear in index

56 Cylinder Seal Assembly P... 25, 29, 31 F D Damper Diagnostic Wire Harness Assembly Directional Exhaust Kit 528P Door Catch Assembly Door Handle Wedge Door Pull Door Pull and Wedge Kit QP WP Door Pull Kit P Door Strike , 19 Door Strike Mount , 19 Drum Light Lamp Dryer Base Dryer Door QP WP Dryer Door Assembly Dryer Door Window E Elbow Shut-Off Valve Electric Clearance Label Electronic Coin Drop Kit CK Electronic Harness Exhaust Duct Expansion Clip , 13 Extractor Tool 128P P Felt Pad , 29 Female Piggyback Terminal Female Pin Terminal Female Spade Terminal Female Tab Terminal Female Terminal Flexible Venting Kit 521P Frame Gusset Front Bulkhead Assembly P Front Panel QP WP Front Panel Seal G Gas Clearance Label Gas Harness Gas Valve Assembly 60353P...37 Gas Valve Mounting Bracket Glass Door Window Glide Kit RB , 29 Graphic Overlay Grounding Clip N/A items do not appear in index

57 H Harness Assembly P , 11 Harness Strap Heat Duct Shroud Heater Assembly P Heater Duct and Screw Assembly P... 33, 35 Heater Kit 964P Heater Kit Assembly Hinge , 19 Hinge Hole Plug Hold Down Kit 526P Housing, 10 Position I Idler Lever Idler Lever and Wheel Assembly Idler Spring Idler Wheel and Bearing Assembly P Igniter and Bracket Assembly P Insulated Female Flag Terminal Insulated Female Spade Terminal K Key L Lead-In Cord Lead-In Pipe Assembly Leveling Leg Light Housing Assembly Limit Thermostat Liner Door Seal P...17, 19 Liner, Seal and Grill Assembly WP DG P...17 Lint Filter DG LG W...25 Lock Cam Lock Kit 27260P...5 L.P. Conversion Kit 458P L.P. Orifice M Male Pin Terminal Male Tab Terminal Meter Case Assembly B Q W...7 Motor and Pulley Assembly P...23 Motor Hub Ring Kit 590P Motor Mount Motor Mount Clamp Motor Pulley Mounting Tool Kit CK N Nut , , 31 N.G. Conversion Kit 459P N/A items do not appear in index

58 N.G. Orifice Ring Terminal Roller Kit RB Rubber Foot O Operating Instruction Label Operating Instructions Label , 13 Outlet Cover , 35 P Panel Locator , 41 Plug Plug, 1 Circuit Plug, 2 Circuit Plug, 9 Circuit R Ratchet Extension Tool 310P Rear Access Panel , 13 Rear Bulkhead Rear Bulkhead Assembly P Receptacle Housing Receptacle, 1 Circuit Receptacle, 10 Circuit Receptacle, 12 Circuit Receptacle, 2 Circuit Receptacle, 3 Circuit Receptacle, 6 Circuit Resistor Retaining Ring , 31 N/A items do not appear in index S Screw M , 13, 21, 25, 29, , , , 29, , 7, 13, 21, 23, 25, 29, 31, 33, 35, 37, , 19, , , , , 13 Screw Orifice Seal Kit RB , 29, 31 Secondary Coil 58804B...37 Security Cabinet Assembly W...13 Security Wrapper Assembly , Q...7 Sensor Shaft 56461P...23, 31 Single Overlay Spade Terminal Speed Clip Strain Relief Switch , 7, 21

59 T Terminal Terminal Block Assembly P Terminal Block Shield Terminal Extractor Tool 283P Thermal Fuse Assembly Thermistor Assembly Thermostat Top Hinge Top Mounting Bracket Top Panel WP Torx Bit 281P P P Torx Drive Tool Transformer P... 5, P... 5 Wire Guard P...9 Wire Harness Assembly P Wire, 12 Gauge Wire, 18 Gauge Wrapper Assembly B W W...13 V Venting Instruction Label W Warning/Caution Label Washer , 31 Window Clip Window Trim Wire Assembly Wire Clip Wire Configuration Assembly P P N/A items do not appear in index

60 Notes