Home Topload Washers

Transcription

1 Home Topload Washers Refer to Page 3 for Model Numbers Parts TLW2C_ Part No R7 February 2018

2

3 Table of Contents Title Page Parts Ordering Information... 2 Serial Plate Location... 2 Model Identification... 3 Graphic Panel, Control Support Panel and Controls (Drawing 1 of 3)... 4 Graphic Panel, Control Support Panel and Controls (Drawing 2 of 3)... 6 Graphic Panel, Control Support Panel and Controls (Drawing 3 of 3)... 8 Lid Switch Assembly Top, Lid and Hood Back Panel Junction Box Fill Hose, Mixing Valve-to-Tub Cover Hose, Mixing Valve and Bracket Motor, Mounting Bracket, Belt, Pump and Idler Assembly Motor, Mounting Bracket, Belt, and Idler Assembly Agitator, Fabric Softener Dispenser, Drive Bell, Hub and Lip Seal Kit and Washtub Outer Tub, Cover, Bearing and Seal Housing, Pressure Hose and Counterweight Drain Hose and Siphon Break Kit Electric Drain Pump, Drain Hose and Siphon Break Kit Weldment and Bearing Assembly, Brake and Pulley Transmission Assembly Front Panel, Base Assembly and Cabinet Kit Mixing Valve and Motor Connection Blocks, Terminals and Extractor Tool Lead-In Cord and Terminals Terminals Shipping Brace, Plug and Special Tools Special Tools Output Board, Wire Harnesses and Wires Wire Harnesses and Wires Parts Index Copyright 2018, Alliance Laundry Systems LLC All rights reserved. No part of the contents of this book may be reproduced or transmitted in any form or by any means without the expressed written consent of the publisher

4 If literature or replacement parts are required, contact the source from whom the machine was purchased or contact Alliance Laundry Systems at (920) for the name and address of the nearest authorized parts distributor. Parts Ordering Information For technical assistance, call the number listed below: (920) Ripon, Wisconsin When calling or writing about your product, be sure to mention model and serial numbers. Model and serial numbers are located on serial plate(s) as shown. Serial Plate Location Serial Plate W429S_

5 Model Identification Information in this manual is applicable to these washer models: AWN432SP113TW01 AWN432SP113TW04 AWNA62SN303AW01 AWNE82SN303AW01 AWNE82SP113TW01 AWNE92SN303AW01 AWNE92SP113TW

6 Graphic Panel, Control Support Panel and Controls (Drawing 1 of 3) Models AWN432SP113TW01 and AWN432SP113TW04 TLW1774P_

7 Graphic Panel, Control Support Panel and Controls (Drawing 1 of 3) REF PART NO. DESCRIPTION COMMENTS 1 D504009WP End Panel Left 2 D Screw W Top Cover Screw Temperature Switch 3 position Pressure Switch P Timer Model AWN432SP113TW01; Models starting serial nos. beginning with P Timer When using P Timer to replace P Timer only one timer wire block connection is used on the timer. Connect the harness to the timer block that the harness plug will accept. The two blocks are unique in design and can not be mis-wired. 8 D504008WP End Panel Right Hold-Down Clip Control Support Panel Grounding Clip W Graphic Panel Timer Skirt Assembly Timer Knob Assembly W Rocker Switch P Knob Assembly P Control Knob Assembly

8 Graphic Panel, Control Support Panel and Controls (Drawing 2 of 3) Models AWNE82SN303AW01, AWNE82SP113TW01, AWNE92SN303AW01 and AWNE92SP113TW01 TLW1772P_

9 Graphic Panel, Control Support Panel and Controls (Drawing 2 of 3) REF PART NO. DESCRIPTION COMMENTS NA P EMI Filter Assembly Models AWNE82SN303AW01 and AWNE92SN303AW01; Includes Nut, Grommet, Junction Box, Screw and Line Filter 1 D504009WP End Panel Left 2 D Screw W Top Cover Screw 5 D504008WP End Panel Right Control Support Panel P Control Assembly Model AWNE92SN303AW01; Includes item P Control Assembly Model AWNE92SP113TW01; Includes item P Control Assembly Model AWNE82SN303AW01; Includes item P Control Assembly Model AWNE82SP113TW01; Includes item Hold-Down Clip P Graphic Panel Overlay Models AWNE92SN303AW01 and AWNE92SP113TW Control Overlay Models AWNE82SN303AW01 and AWNE82SP113TW Screw

10 Graphic Panel, Control Support Panel and Controls (Drawing 3 of 3) Model AWNA62SN303AW01 TLW1874P_

11 Graphic Panel, Control Support Panel and Controls (Drawing 3 of 3) REF PART NO. DESCRIPTION COMMENTS 1 D504009WP End Panel Left 2 D Screw W Top Cover Screw Bracket Temperature Switch 3 position Cycle Switch Bracket Cycle Switch 9 D504008WP End Panel Right Screw Hold-Down Clip Control Assembly Control Support Panel Indicator Light P Knob Assembly W Push-to-Start Switch Indicator Light Lens W Rocker Switch P Control Knob Assembly W Graphic Panel

12 Lid Switch Assembly TLW1797P_

13 Lid Switch Assembly REF PART NO. DESCRIPTION COMMENTS Lid Switch Drip Shield Models AWNA62SN303AW01, AWNE82SN303AW01 and AWNE92SN303AW01 2 M Screw 3 M Nut Screw Switch Lid Switch Assembly

14 Top, Lid and Hood Back Panel TLW1823P_

15 Top, Lid and Hood Back Panel REF PART NO. DESCRIPTION COMMENTS WP Lid Lid Warning Label Pressure Sensor Models AWNE82SP113TW01 and AWNE92SP113TW Hood Back Panel Model AWNA62SN303AW Hood Back Panel Models AWNE82SN303AW01 and AWNE92SN303AW Hood Back Panel Model AWN432SP113TW Hood Back Panel All other models Screw 5 B Pressure Switch Model AWN432SP113TW Tubing Model AWN432SP113TW Barbed Tee Model AWN432SP113TW Screw Bushing 10 D Disconnect Power Warning Label Strain Relief Screw Models AWNA62SN303AW01, AWNE82SN303AW01 and AWNE92SN303AW Hold-Down Clip Top Shield Models AWNA62SN303AW01, AWNE82SN303AW01 and AWNE92SN303AW Grommet Models AWNA62SN303AW01, AWNE82SN303AW01 and AWNE92SN303AW Inlet Cover Inlet Deflector Hinge Stop Clip Screw WP Top Bleach Dispenser Lid Hinge Right Lid Hinge Left Bumper

16 Junction Box Models AWNA62SN303AW01, AWNE82SN303AW01 and AWNE92SN303AW01 TLW1875P_

17 Junction Box REF PART NO. DESCRIPTION COMMENTS NA Cable Tie Nut Line Filter Junction Box Screw Pressure Sensor Grommet

18 Fill Hose, Mixing Valve-to-Tub Cover Hose, Mixing Valve and Bracket C H TLW1798P_

19 Fill Hose, Mixing Valve-to-Tub Cover Hose, Mixing Valve and Bracket REF PART NO. DESCRIPTION COMMENTS Valve to Inlet Hose Screw Hose Clamp Mixing Valve Mounting Bracket 5 F Water Hose 5 feet; Models AWN432SP113TW01, AWN432SP113TW04, AWNE82SP113TW01 and AWNE92SP113TW Washer Filter screen Washer Flow restrictor; Water pressure reducer; Available for water pressure up to but not exceeding 120 psi Fill Hose Braided; 4 feet; Marked for hot water; 2 standard thread hose couplings; Models AWN432SP113TW01, AWN432SP113TW04, AWNE82SP113TW01 and AWNE92SP113TW Fill Hose Braided; 4 feet; Marked for cold water; 2 standard thread hose couplings; Models AWN432SP113TW01, AWN432SP113TW04, AWNE82SP113TW01 and AWNE92SP113TW Fill Hose Rubber; 8 feet; Models AWN432SP113TW01, AWN432SP113TW04, AWNE82SP113TW01 and AWNE92SP113TW Fill Hose Rubber; 10 feet; Models AWN432SP113TW01, AWN432SP113TW04, AWNE82SP113TW01 and AWNE92SP113TW Fill Hose Braided; 4 feet; Marked for hot water; 1 BSPP thread hose coupling and 1 standard thread hose coupling; Models AWNA62SN303AW01, AWNE82SN303AW01 and AWNE92SN303AW Fill Hose Braided; 4 feet; Marked for cold water; 1 BSPP thread hose coupling and 1 standard thread hose coupling; Models AWNA62SN303AW01, AWNE82SN303AW01 and AWNE92SN303AW Fill Hose Rubber; 4 feet; Models AWNA62SN303AW01, AWNE82SN303AW01 and AWNE92SN303AW Fill Hose Rubber; 10 feet; Models AWNA62SN303AW01, AWNE82SN303AW01 and AWNE92SN303AW Washer Mixing Valve Screen P Mixing Valve Models AWNA62SN303AW01, AWNE82SN303AW01 and AWNE92SN303AW P Mixing Valve All other models Screw Hose Clamp Mixing Valve Shield Models AWNA62SN303AW01, AWNE82SN303AW01 and AWNE92SN303AW

20 Motor, Mounting Bracket, Belt, Pump and Idler Assembly Models AWN432SP113TW01, AWN432SP113TW04, AWNE82SP113TW01 and AWNE92SP113TW01 TLW1819P_

21 Motor, Mounting Bracket, Belt, Pump and Idler Assembly REF PART NO. DESCRIPTION COMMENTS Motor Shield Screw P Motor Kit Includes Capacitor Nut Motor Mount Bracket Idler Lever Spring Nut Idler Lever Washer Screw Idler Shaft 12 D Washer Washer Nylatron Retaining Ring P Idler Pulley P3 Idler Lever Kit Includes items 4, 6, 7-15 and Agitate and Spin Belt P Pump 19 RB Belt and Pump Kit Includes items 17 and Spring Clip Screw Nut Isolator Post Motor Mount Capacitor Screw Screw Motor Drip Shield Capacitor Clamp Washer Motor Mount

22 Motor, Mounting Bracket, Belt, and Idler Assembly Models AWNA62SN303AW01, AWNE82SN303AW01 and AWNE92SN303AW01 TLW1820P_

23 Motor, Mounting Bracket, Belt, and Idler Assembly REF PART NO. DESCRIPTION COMMENTS Motor Shield Screw P Motor Assembly 2 speed; 240Volt/50 Hertz Nut Motor Mount Bracket Idler Lever Spring Tube Nut Idler Lever Washer Screw Idler Shaft 13 D Washer Washer Nylatron Retaining Ring P Idler Pulley Idler Lever and Belt Kit Includes items 4, 6, 8-16 and Agitate and Spin Belt Screw Nut Isolator Post Motor Mount Capacitor Screw Screw Motor Drip Shield Capacitor Clamp Washer Motor Mount

24 Agitator, Fabric Softener Dispenser, Drive Bell, Hub and Lip Seal Kit and Washtub TLW1781P_

25 Agitator, Fabric Softener Dispenser, Drive Bell, Hub and Lip Seal Kit and Washtub REF PART NO. DESCRIPTION COMMENTS Screw Balance Ring Assembly 3 719P3 Washtub Kit Stainless steel Washtub Gasket Models AWN432SP113TW01, AWN432SP113TW04, AWNE82SN303AW01 and AWNE82SP113TW P3A Hub and Lip Seal Kit DO NOT use any sealant other than P Sealant; Includes item 10 and installation tool P Sealant Use with hub and lip seal kit Spline Insert Nut Bell and Transmission Tube Seal Lint Filter Models AWNE92SN303AW01 and AWNE92SP113TW01; Models through serial nos. beginning P Drive Bell and Seal Kit Includes items 8, 11 and Screw Bell Plug Flex Vane Agitator Fabric Softener Dispenser Assembly

26 Outer Tub, Cover, Bearing and Seal Housing, Pressure Hose and Counterweight TLW1807P_

27 Outer Tub, Cover, Bearing and Seal Housing, Pressure Hose and Counterweight REF PART NO. DESCRIPTION COMMENTS Tub Cover Assembly Includes item Tub Cover Gasket P Outer Tub Assembly Leg Plate Screw Leg Spring Screw Counterweight Assembly Washer P3A Hub and Lip Seal Kit P Sealant Use with hub and lip seal kit 11 D Warning Label Grommet Pressure Bulb Hose Clamp Hose Clip Cable Clip Tubing Model AWN432SP113TW Tubing All other models

28 Drain Hose and Siphon Break Kit Models AWN432SP113TW01, AWN432SP113TW04, AWNE82SP113TW01 and AWNE92SP113TW01 Standpipe W329P_

29 Drain Hose and Siphon Break Kit REF PART NO. DESCRIPTION COMMENTS NA 451P3 Drain Extension Kit 1 562P3 Siphon Break Kit Siphon break kit MUST be installed in drain hose if drain receptacle is lower than cabinet top of washer; Optional Standpipe Strap Drain Hose Sleeve Standpipe Adapter Strain Relief Drain Hose Hose Stand 8 F Hose Clamp Tub-to-Pump Hose Retainer Clip

30 Electric Drain Pump, Drain Hose and Siphon Break Kit Models AWNA62SN303AW01, AWNE82SN303AW01 and AWNE92SN303AW01 W378P_

31 Electric Drain Pump, Drain Hose and Siphon Break Kit REF PART NO. DESCRIPTION COMMENTS NA 451P3 Drain Extension Kit 1 562P3 Siphon Break Kit Siphon break kit MUST be installed in drain hose if drain receptacle is lower than cabinet top of washer Drain Hose Sleeve Standpipe Strap Drain Hose Hose Stand P Drain Pump Pump Bracket Screw Metric 9 D Screw Pump Isolator Pump Shield Hose Clamp Retainer Clip Tub-to-Pump Hose 15 F Hose Clamp Strain Relief

32 Weldment and Bearing Assembly, Brake and Pulley TLW1841P_

33 Weldment and Bearing Assembly, Brake and Pulley REF PART NO. DESCRIPTION COMMENTS Weldment and Bearing Assembly P Brake Kit 3 735P3 Brake Pad Kit Includes 3 pads P Silicone Grease Apply small amount to each new brake pad Screw Washer Thin Washer Thick Washer For machines experiencing squeaking during agitation; Through Serial Nos. beginning Washer Starting Serial Nos. beginning P Silicone Grease Apply small amount to washer Pulley Washer Screw Helix RP Lower Bearing

34 Transmission Assembly TLW1838P_

35 Transmission Assembly REF PART NO. DESCRIPTION COMMENTS NA 27604P Anti-Seize Compound Apply to smooth area of both the upper and lower transmission tube that will be contacting the upper and lower bearings and apply to spline area of upper and lower transmission tube that will be contacting the washtub Transmission Assembly Includes item 2 and Hub and Lip Seal Kit; Lip seal models only P Sealant

36 Front Panel, Base Assembly and Cabinet Kit Ground Wire TLW1843P_

37 Front Panel, Base Assembly and Cabinet Kit REF PART NO. DESCRIPTION COMMENTS NA 122P4P Porcelain Touch-Up Paint Bumper Pad Foam Pad Panel Locator Screw Bumper Pad Screw 7 D Screw Hold-Down Lug Hinge Warning Label WP Service Cabinet Kit Screw Leg and Stabilizer Assembly Screw Bracket Right Rubber Foot Base Assembly Leveling Leg Nut Friction Ring P3 Adjustable Leg Extension Kit Bracket Left Front Panel Pad Panel Locator Foam Pad WP Front Panel Screw Hold-Down Clip Front Panel Brace

38 Mixing Valve and Motor Connection Blocks, Terminals and Extractor Tool W134PZ3A_

39 Mixing Valve and Motor Connection Blocks, Terminals and Extractor Tool REF PART NO. DESCRIPTION COMMENTS Circuit Plug Motor Female Terminal For 1 or 2 wire application Female Spade Terminal 1/4 inch Mixing Valve Plug Natural Mixing Valve Plug Red 5 283P4 Terminal Extractor Tool

40 Lead-In Cord and Terminals GROUND WIRE TLW1518P_

41 Lead-In Cord and Terminals REF PART NO. DESCRIPTION COMMENTS Position Housing Right; Black Female Terminal For 1 or 2 wire application SG Terminal 3 D Screw Insulated Female Spade Terminal Lead-In Cord Models AWNA62SN303AW01, AWNE82SN303AW01 and AWNE92SN303AW Lead-In Cord All other models Male Pin Terminal Circuit Plug Cable Clip Circuit Receptacle SG Female Pin Terminal Harness Strap Wire Tie

42 Terminals TLW1780P_

43 Terminals REF PART NO. DESCRIPTION COMMENTS Grounding Clip SG Terminal Grounding Clip 2 D Wire Clip Female Spade Terminal Large spade Terminal Tab Ring Terminal Small shank Pressure Switch Terminal

44 Shipping Brace, Plug and Special Tools TLW1661P_

45 Shipping Brace, Plug and Special Tools REF PART NO. DESCRIPTION COMMENTS NA 725P3 Tool Kit Includes items 3, 4, drive bell seal tool, tub cover removal tool, agitator hook and torx bit NA Foam Shipping Brace Install before moving washer NA Washer Installation Kit Shipping Brace Install whenever moving washer; Remove before use Shipping Plug Install before moving washer to prevent tub from damaging cabinet 3 321P4 Spring Hook Tool For removal of module springs from outer tub 4 306P4 Hex Wrench Tool For removal of locknut from washtub hub

46 Special Tools TLW1534P_

47 Special Tools REF PART NO. DESCRIPTION COMMENTS NA 725P3 Tool Kit Includes items 4, 5, spring hook, hex wrench, tub cover removal tool and Torx bit 1 294P4 Agitator Drive Bell Puller For removal and installation of drive bell to transmission shaft 2 294P4B Bolt Use to update item P4A Drive Bell Puller Arm Use to update item P4 Drive Bell Seal Tool For installation of Bell and Transmission Tube Seal 5 254P4P Agitator Hook Set of 2; Use to remove agitator from drive bell

48 Output Board, Wire Harnesses and Wires Models AWNA62SN303AW01, AWNE82SN303AW01, AWNE82SP113TW01, AWNE92SN303AW01 and AWNE92SP113TW01 TLW1776P_

49 Output Board, Wire Harnesses and Wires REF PART NO. DESCRIPTION COMMENTS NA Gauge Wire Black; Order wire by foot and terminals as required NA Gauge Wire Orange; Order wire by foot and terminals as required NA Hood Harness Model AWNA62SN303AW Control Harness Models AWNA62SN303AW01, AWNE82SN303AW01 and AWNE92SN303AW Control Harness Models AWNE82SP113TW01 and AWNE92SP113TW Pressure Sensor Harness Screw Output Control Shield Shield Assembly Includes items 4 and Output Board Cover Gasket P Output Board Control Assembly NOTE: Individual wires are not available separately. Order complete wire harness, or order wire by the foot. When applying terminals to wires, it is recommended that the terminals be soldered to the wires

50 Wire Harnesses and Wires Models AWN432SP113TW01 and AWN432SP113TW04 TLW1777P_

51 Wire Harnesses and Wires REF PART NO. DESCRIPTION COMMENTS NA Gauge Wire Black; Order wire by foot and terminals as required NA Gauge Wire Orange; Order wire by foot and terminals as required Hood Timer Harness Model AWN432SP113TW Hood Timer Harness Model AWN432SP113TW P Wire Harness Assembly NOTE: Individual wires are not available separately. Order complete wire harness, or order wire by the foot. When applying terminals to wires, it is recommended that the terminals be soldered to the wires

52 Notes

53 Parts Index A Adjustable Leg Extension Kit 566P Agitate and Spin Belt Agitator Drive Bell Puller 294P Agitator Hook 254P4P Anti-Seize Compound 27604P B Balance Ring Assembly Barbed Tee Base Assembly Bell and Transmission Tube Seal Bell Plug Belt and Pump Kit RB Bleach Dispenser Bolt 294P4B Bracket Brake Kit 38505P Brake Pad Kit 735P Bumper Bumper Pad Bushing C Cable Clip , 39 Cable Tie Capacitor Capacitor Clamp , 21 Control Assembly P P P P Control Harness Control Knob Assembly P...5, 9 Control Support Panel , 9 Counterweight Assembly Cycle Switch Cycle Switch Bracket D Disconnect Power Warning Label D Drain Extension Kit 451P3...27, 29 Drain Hose Drain Hose Sleeve , 29 Drain Pump 39255P...29 Drive Bell and Seal Kit 39508P...23 Drive Bell Puller Arm 294P4A...45 Drive Bell Seal Tool 293P E EMI Filter Assembly End Panel D504008WP...5, 7, 9 D504009WP...5, 7, 9 F Fabric Softener Dispenser Assembly Female Pin Terminal 00574SG...39 N/A items do not appear in index

54 Female Spade Terminal Female Terminal , 39 Fill Hose Flex Vane Agitator Foam Pad Foam Shipping Brace Friction Ring Front Panel 38335WP Front Panel Brace Front Panel Pad G Graphic Panel P W W... 5 Grommet , 15 Grounding Clip , 41 H Harness Strap Helix Hex Wrench Tool 306P Hinge Stop Clip Hold-Down Clip , 7, 9, Hold-Down Lug Hinge Hood Back Panel Hood Harness Hood Wire Harness Assembly Hose Clamp F , Hose Clip Hose Stand , 29 Housing, 24 Position Hub and Lip Seal Kit 766P3A...23, 25 I Idler Lever , 21 Idler Lever and Belt Kit Idler Lever Kit 959P Idler Lever Spring Idler Pulley 38225P...19, 21 Idler Shaft , 21 Indicator Light Indicator Light Lens Inlet Cover Inlet Deflector Insulated Female Spade Terminal Isolator Post , 21 J Junction Box K Knob Assembly P P...9 N/A items do not appear in index

55 L Lead-In Cord Leg and Stabilizer Assembly Leg Plate Leg Spring Leveling Leg Lid 37395WP Lid Hinge Lid Switch Assembly Lid Switch Drip Shield Lid Warning Label Line Filter Lint Filter Lower Bearing 28944RP M Male Pin Terminal Mixing Valve P P Mixing Valve Mounting Bracket Mixing Valve Plug Mixing Valve Screen Mixing Valve Shield Motor Assembly P Motor Drip Shield , 21 Motor Mount , , 21 Motor Mount Bracket , 21 Motor Shield , 21 N Nut O M , , , 21 Outer Tub Assembly P...25 Output Board Control Assembly P...47 Output Board Cover Gasket Output Control Shield Overlay P Panel Locator Plug, 10 Circuit Plug, 9 Circuit Porcelain Touch-Up Paint 122P4P...35 Pressure Bulb Pressure Sensor , 15 Pressure Sensor Harness Pressure Switch B Pressure Switch Terminal Pulley Pump P...19 Pump Bracket Pump Isolator Pump Shield Push-to-Start Switch W...9 N/A items do not appear in index

56 R Receptacle, 9 Circuit Retainer Clip , 29 Retaining Ring , 21 Ring Terminal Rocker Switch 38424W... 5, 9 Rubber Foot S Screw D , 7, 9, 35 D D M , 7, 9, 11, , , , , 21, , , , 47 Sealant P... 23, 25, 33 Service Cabinet Kit 38612WP Shield Assembly Shipping Brace Shipping Plug Silicone Grease 26594P Siphon Break Kit 562P , 29 Spline Insert Spring Clip Spring Hook Tool 321P Standpipe Adapter Standpipe Strap , 29 Strain Relief , Switch T Temperature Switch , 9 Terminal 00568SG...39 Terminal Extractor Tool 283P Terminal Grounding Clip 00569SG...41 Terminal Tab Timer P P...5 Timer Knob Assembly Timer Skirt Assembly Tool Kit 725P3...43, 45 Top 37992WP...13 Top Cover 39905W...5, 7, 9 Top Shield Transmission Assembly Tub Cover Assembly Tub Cover Gasket Tube Tubing Tub-to-Pump Hose V Valve to Inlet Hose N/A items do not appear in index

57 W Warning Label D Washer D , , , , 21 Washer Installation Kit Washtub Gasket Washtub Kit 719P Water Hose F Weldment and Bearing Assembly Wire Clip D Wire Harness Assembly Wire Tie Wire, 12 Gauge , 49 Wire, 18 Gauge , 49 N/A items do not appear in index

58 Notes