Hydraulic Power Console HE V

Transcription

1

2 content Technical data page 3 Manual page 5 Hydraulic Schematic page 6 Electrical wiring diagram page 7 Parts Plan page 8 Parts List page 9

3 Technical data Engine construction motor power Three-phase motor 1,1kW in continuous operation Hydraulikpumpe constrction 3-stage Radial piston pump flow 7,2 l/min bis 70 bar 2,5 l/min bis 200 bar 0,9 l/min bis 800 bar maximum pressure 800 bar hydraulic control Wegeventil construction 4/2-poppet valve, electromagnetically actuated flow max. 12 l/min maximum pressure 800 bar actuating voltage 1~400V 50Hz Druckventil (Drehmomentventil) construction spring-loaded Ball seat valve, manually adjustable flow max. 12 l/min maximum pressure 800 bar adjustment ca. 25 bis 800 bar Rückdruckventil construction spring-loaded cone seat valve, fixed flow max. 15 l/min maximum pressure 215 bar adjustment ca. 25 bis 110 bar Manometer construction Bourdon gauge, glycerine filled size Ø100 mm accuracy Kl. 1,0

4 Technical data dimensions and weights main dimensions weight without oil Gewicht operational LxBxH440x240x470 mm 22,0 kg 28,0 kg oil filling capacity 6 l viscosity ISO VG 46 protection protection class IP 54 Attention: No ex. protection!

5 Operation Manual Prior to using the pump Using the dipstick check the oil level in the tank. Check the pump, remote control and hydraulic twin line hoses for signs of damage. Connect the remote control unit. Connect the hydraulic hoses to the pump and tool ensuring that the couplings are free of grit or dirt. Ensure that the torque control valve is set to zero by fully rotating it counter-clockwise. Connect the pump to the correct electrical supply. (See unit for details) Operation Start the motor by pressing and releasing the white button on the remote control. The tool is pressurised by holding the white button down and depressurised by releasing it. Pressing the black button on the remote control the motor stops. The motor will be stopped automatically after approximately 1 minute without any operation of the remote control. Torque setting While the motor is running press the white button on the remote control and hold it until the piston is fully advanced. Continue to hold the white button and slowly rotate the torque control valve in a clockwise direction until the required pressure/torque is shown on the pressure gauge. The white button should then be released, allow the piston to fully retract and then operate the unit one more time to check the output pressure/torque is correct. If not repeat. To reduce the pressure/torque turn the torque control valve anti-clockwise. If the desired pressure/torque has been reached rotate the wing nut on the torque control valve clockwise. This will lock the torque control valve in place. To achieve full torque it is important that the wing nut on the torque control valve is rotated fully anti-clockwise against the bottom of torque control valve and that the torque control valve is turned fully clockwise. Tightening and loosening bolts For bolting consult the tool manual. After use Switch off the motor using the black switch on the remote control unit. Turn off the electrical supply. Having ensured that hydraulic pressure has been released, disconnect the hydraulic hoses.

6 Hydraulikschaltplan

7

8

9 Hydraulic Power Console HE V Parts List Pos. designation part Number 1 Electric motor control DAS71G k 2 Pump unit complete KP Wear rate for pumping unit VS KP oil tank incl gasket AB 7 D GK 4 Oil drain screw GN740-G1/4 5 Ölschauglas mit Thermometer GN B 6 bleed screw GN G3/8-A-2 7 valve block compl. MI 230V 800bar 8 clutch Kit Cejn pressure adjusting valve (new) MVE4AR pressure adjusting valve (exchange) MVE4AR-700 AT 10 manometer NG b Kl 1,0 11 solenoid valve WG4-1 R WG230V 12 carrying handle TR DKW oil cooler V 14 remote Control (no picture) FB el. 5m k