APV DELTA SVS1F DN

Transcription

1 INSTRUCTION MANUAL APV DELTA SVSF DN BUTTERFLY VALVE FORM NO.: H20570 REVISION: UK-5 READ AND UNDERSTAND THIS MANUAL PRIOR TO OPERATING OR SERVICING THIS PRODUCT. Scan for SV/SVSF Valve Maintenance Video

2

3 UK EU Declaration of Conformity for Valves and Valve Manifolds SPX FLOW TECHNOLOGY GERMANY GMBH Gottlieb-Daimler-Str. 3, D Holzwickede herewith declares that the APV double seal and double seat valves of the series SD4, SDT4, SDU4, SDMS4, SDMSU4, SDTMS4, SWcip4, DSV, DA3, DA3SLD, DE3, DEU3, DET3, DKR2, DKRT2, DKRH2 in the nominal diameters DN 25-50, ISO 6 and Sh5-6 Sh5 APV butterfly valves of the series SV and SVSF, SVL and SVSL in the nominal diameters DN 25-00, DN and ISO 4 APV ball valves of the series KHI, KHV in the nominal diameters DN 5-00 APV single seat, diaphragm and spring loaded valves of the series S2, SW4, SWhp4, SW4DPF, SWmini4, SWT4, SWS4, MF4, MS4, MSP4, AP/T, CPV, RG4, RG4DPF, RGMS4, RGE4, RGE4DPF, RGEMS4, PR2, PRD2, SI2, UF/R3, VRA/H in the nominal diameters DN 0-50, ISO /2 4 and Sh5-6 Sh5 and the valve manifolds installed thereof meet the requirements of the Directives 2006/42/EC (superseding 89/392/EEC and 98/37/EC) and ProdSG (superseding GPSG - 9.GPSGV). For official inspections, SPX FLOW presents a technical documentation according to Appendix VII of the Machinery Directive, this documentation consisting of documents of the development and construction, description of measures taken to meet the conformity and to correspond with the basic requirements on safety and health, incl. an analysis of the risks, as well as an operating manual with safety instructions. The conformity of the valves and valve manifolds is guaranteed. Authorised person for the documentation: Frank Baumbach SPX FLOW TECHNOLOGY GERMANY GMBH Gottlieb-Daimler-Str. 3, D Holzwickede, Germany November 207 Frank Baumbach Regional Engineering Manager, F&B Components

4

5 APV UK APV_SVSF _UK-5_08207.qxp Content Page. General Terms 2 2. Safety Instructions Intended Use 3 4. Mode of Operation General terms 5. Auxiliary Equipment Valve position indication - actuated valve 5.2. Valve position indication - manually operated valve 5.3. Control Unit 5.4. Adapter for Control Unit Adapter for Control Unit 5.5. Turning actuator for Control Unit 6. Cleaning Cleaning recommendation 7. Installation Welding instructions 8. Dimensions / Weights 9 9. Technical Data General terms 9.2. Compressed air quality 9.3. Table: tightening torque, pneumatic air consumption, kvs-values 0. Materials. Maintenance 2 2. Service Instructions Dismantling from the line system 2.2. Disassembly of actuating device 2.3. Dismantling of inner parts 2.4. Replacement of seals 2.5. Installation of seals and bearing bushes 2.6. Installation of actuating device 2.7. Installation of proximity switches 3. Spare Parts Lists 6 (see attachment) SVSF - NC DN RN SVSF - M DN RN Handle with locking device SVSF - DN RN Handle with locking device for valve position indication SVSF - DN RN Turnign actuator K-80, K-25, K-80 spring/air - RN Turning actuator spring/air for feedback unit - RN Butterfly Valve DELTA SVSF DN Instruction Manual: UK - rev. 5

6

7 APV UK APV_SVSF _UK-5_08207.qxp. General Terms This instruction manual has to be read carefully and observed by the responsible operating and service personnel. We do not accept any liability for damage or malfunctions resulting from the non-compliance with this instruction manual. Descriptions and data given herein are subject to technical changes. 2. Safety Instructions The valve must only be assembled, operated, disassembled and maintained by persons who have been trained in APV valves or by SPX FLOW service team members. If necessary, contact your local SPX FLOW representative. DANGER!!!!!! - The technical safety symbol draws your attention to important directions for operating safety. You will find it wherever the activities described are bearing health hazards or risks for persons or material assets. - Do not reach into the open valve or into the yoke! Risk of bruising at movable parts of the valve. - In dismantled state there is the risk of injury by sudden valve operation. - Regular maintenance including replacement of seals and bearing bushes must be scheduled for the valve in order to prevent leakages. - Before any maintenance of the valve, the line system must be depressurized and discharged if possible. - Electric and pneumatic connections must be separated. - Observe the following Service Instructions to ensure safe maintenance of the valve. Butterfly Valve DELTA SVSF DN Instruction Manual: UK - rev. 5 2

8 APV UK APV_SVSF _UK-5_08207.qxp 2. Safety Instructions! DANGER! Welded actuators are preloaded by spring force. Opening of the actuators is strictly forbidden. Danger to life! Actuators which are no longer used and / or defective must be disposed in professional manner. Defective actuators must be returned to your SPX FLOW representative for their professional disposal and free of charge for you. Please address to your local SPX FLOW representative. 3. Intended Use The intended use as field of application of the butterfly valve is the shut-off of pipeline sections. Arbitrary, structural changes at the valve may affect safety as well as the intended functionality of the valve and are not permissible. 3 Butterfly Valve DELTA SVSF DN Instruction Manual: UK - rev. 5

9 APV UK APV_SVSF _UK-5_08207.qxp 4. Mode of Operation 4.. General terms Use of high-quality stainless steel and seal materials to the specified requirements, the butterfly valve range DELTA SVSF is applicable in the food and beverage industries as well as in the chemical and pharmaceuticl industries. Valves of the series DELTA SVSF can either be operated manually or remote controlled via a pneumatic actuator. Manual operation and pneumatic actuator including add-on pieces are interchangeable. In the standard version NC, the pneumatic turning actuator opens the valve with compressed air. Reset by spring force into the limit position closed. Extension of operating time of actuated valves by pneumatic air throttle or adjusting screw in the control unit to optimize the flow behaviour and, if required, to reduce pressure hammers arising in the installation. The butterfly valve can also be used in vacuum systems. The valve opens and closes by turning the valve disc by 90. Smooth valve passage without diversion of line flow. The opening diameter complies with the size of the inner line diameter. Butterfly Valve DELTA SVSF DN Instruction Manual: UK - rev. 5 4

10 APV UK APV_SVSF _UK-5_08207.qxp 5. Auxiliary Equipment 5.. Valve position indication - valve with pneumatic actuator Proximity switches to signal the limit position of the valve disc can be installed in the yoke area if required. We recommend to use our APV standard proximity switches. Type: three-wire proximity switch (ref.-no /93, H6223) Operating distance: 4mm / diameter: mm / length: 30 mm. Feedback complete with support and proximity switch (ref.-no /93; H32725) for a limit position. Using a valve position indicator other than APV, we cannot accept any liability for faulty function Valve position indication - valve with manual operation A specific manual actuation with feedback feature is available: Feedback of the two disc positions open and closed is possible. 5 Butterfly Valve DELTA SVSF DN Instruction Manual: UK - rev. 5

11 APV UK APV_SVSF _UK-5_08207.qxp 5. Auxiliary Equipment fig Control Unit CU Units with feedback switch and magnet valve for the pneumatic control of the valve for assembly on the actuator are also available in fieldbus technology. The assembly of a control unit on a pneumatic actuator is possible. The following different designs are available: Control Unit CU3 Direct Connect AS-i extended 62 slaves DeviceNet Profibus CU4-T-Direct Connect /93; H32046 CU4-T-AS-i extended /93; H CU3 DeviceNet /93; H CU3 Profibus /93; H Adapter for control unit (fig. 5.4.) CU3 Profibus, CU3 Device Net The following adapters are required to install the control unit on the SVSF valve. Spare parts for CU2 adapter fig Item Pcs. Designation - - CU2 adapapter SVSF25-250, DKR80-00 reference No. ID - No /93 H CU operating cam cpl. SVS/DKR /93 H * cyl. screw ISO207 M5x8-A2-7 3 adapter set - 4 o-ring 88,62-,78 NBR o-ring 5,28-,78 NBR - 6 CU adapter for SVS,DKR 7* o-ring 90-2 NBR * scope of supply - actuator 8 v-seal 20x28x4 9 o-ring 3,0-2,0 NBR 70 0 o-ring -3 NBR 2 blind plug G/8" /5 H /93 H /83 H /83 H /93 H /83 H /83 H /83 H /83 H /93 H20885 Butterfly Valve DELTA SVSF DN Instruction Manual: UK - rev. 5 6

12 APV UK APV_SVSF _UK-5_08207.qxp 5. Auxiliary Equipment Adapter for control unit (fig ) CU4-T-Direct Connect, CU4-T-AS-i extended The following adapter is required to install the control unit CU4 on the SVSF valve. fig Spare Parts for CU4 T adapter 7 Item Pcs. Designation reference No. ID - No CU4 Tmax-adapter cpl. CU4 T-adapter 2 3 cyl. screw ISO207 M5x6-A /93 H /93 H /3 H o-ring,-,78 NBR 70shore A 5 o-ring 6-2 NBR 6 o-ring 0,27-2,62 7 CU4 operating cam complete /83 H /83 H /83 H /93 H CU4 SVS, DKR, K operating rod 9 o-ring -3 NBR 0 v-seal 20x28x4 2 CU4 clamp halves complete 2 2 cyl. screw ISO 4762 M4x40 inner hexagon /2 H /83 H /83 H /93 H /3 H Turning actuator for control unit - For the assembly of a control unit on the butterfly valve a special turning actuator is required. The standard turning actuator must be replaced. Turning actuator for control unit DN / K25 F/L-RM /7 H28942 DN / K80 F/L-RM /7 H Butterfly Valve DELTA SVSF DN Instruction Manual: UK - rev. 5

13 APV UK APV_SVSF _UK-5_08207.qxp 6. Cleaning 6.. Cleaning recommendation The valve passage is cleaned by cleaning liquids during cleaning of the connected pipelines. Depending on the degree and constituents of soiling, the cleaning liquids, times and processes must be scheduled for the individual application. The compatibility of the individually selected cleaning processes and liquids with the respectively used seals must be verified. 7. Installation In normal installation position, the actuator is positioned vertically to the top. Depending on the respective application, optional installation positions can, however, also be realized. Installation can optionally be undertaken between FG flanges and flanges according to DIN. Attention: Observe welding instructions! 7.. Welding Instructions - Welding may only be carried out by certified welders (DIN EN ISO ). (seam quality DIN EN ISO 587). - The welding of the mating flanges must be effected in such a way that deformation strain cannot be transferred to the housing halves. - TIG orbital welding is the most appropriate method. - Before welding, all sensitive parts must be removed! Dismantle the valve core with seals from between the mating flanges. - After welding of the mating flanges and after work at the pipelines, the corresponding parts of the installation or pipelines must be cleaned from welding residues and soiling. If these cleaning instructions are not observed, welding residues and dirt particles can settle in the valve and cause damage or be carried over to other parts of the installation. - Any damage resulting from the non-observance of these welding instructions is not subject to our guarantee. Butterfly Valve DELTA SVSF DN Instruction Manual: UK - rev. 5 8

14 APV UK APV_SVSF _UK-5_08207.qxp 8. Dimensions / Weights SVSF with turning actuator and CU4 control unit SVSF with turning actuator SVSF with manual actuation H Ø F G A E K Ø D Ø D Ø D B B A Dimensions in mm C E E DN A A B C Ø D E Ø F G H K Weights DN manual actuated 25 2,9 20,9 50 5,6 23, ,6 39, ,2 53,2 9 Butterfly Valve DELTA SVSF DN Instruction Manual: UK - rev. 5

15 APV UK APV_SVSF _UK-5_08207.qxp 9. Technical Data angle union - G/8" slewable tightening torque 2 Nm 9.. General data - max. line pressure : 0 bar - max. operating temperature : 35 o C EPDM, HNBR * VMQ, * FPM - short-term load : 40 o C EPDM, HNBR * VMQ, * FPM * (no steam) - vacuum tightness : 2 mbar - opening angle of butterfly valve : 90 o min. air pressure for actuator : 6 bar max. air pressure for actuator : 0 bar actuator spring/air - air connection (for hose) : 6 x elbow union - G/8" slewable : tightening torque 2 Nm 9.2. Compressed air quality: Quality class acc. to DIN ISO content of solid particles: Quality Class 3 max. size of solid particles per m³ 0000 of 0,5 µm < d <,0 µm 500 of,0 µm < d < 5,0 µm content of water: Quality Class 3 max. dew point temperature -20 C For installations at lower temperatures or at higher altitudes, additional measures must be considered to reduce the pressure dew point accordingly. content of oil: Quality Class max. 0,0 mg/m³ The oil applied must be compatible with Polyurethane elastomer materials DELTA SVSF DN Turning actuator K25 K25 K80 K80 Required tightening torque Md Nm Pneumatic air consumption at 6bar V NL 5,5 5,5 Kvs - values in m³/h Butterfly Valve DELTA SVSF DN Instruction Manual: UK - rev. 5 0

16 APV UK APV_SVSF _UK-5_08207.qxp 0. Materials - valve disc.4404 /.457 (DIN 0088) - housing flange / mating flanges.4404 (DIN EN 0088) - SV seal, flange seal standard: option: EPDM HNBR, VMQ, FPM - bearing bush polyamide - handle (DIN EN 0088) actuator - yoke, turning actuator, bracket (DIN EN 0088) - coupling indicator PE - hard - spindle bearing polyamide PA 2 / POM - piston polyacetal POM - air connection polyamide PA 6.6 Butterfly Valve DELTA SVSF DN Instruction Manual: UK - rev. 5

17 APV UK APV_SVSF _UK-5_08207.qxp. Maintenance Scan for SV/SVSF Valve Maintenance Video - The maintenance intervals depend on the application of the valve and should be determined by the operator carrying out regular checks of the valve. - There are just a few wear parts in butterfly valves: the SV seal, flange seals and bearing bushes. - It is recommended that spare seals and bearings are kept by the user. Complete seal kits for the valve service are available (see spare parts lists). - If damaged seals are replaced, generally all seals and bearing bushes should be changed. grease SV seal grease grease - Dismantling and installation of seals according to Service Instructions. - All seals must be slightly greased before their installation. Grease SV seal according to fig. - especially in the cross bores. - Assembly of valve and change of valve design NC or NO according to Service Instructions. - Installation of turning actuator according to Service Instructions. - The inner parts of the actuator are maintenance free. Attention! Use food-grade special grease being suited for the respective seal material, only. Recommendation: APV assembly grease for EPDM, FPM, HNBR and NBR (0,75 kg /can - ref. No /93; H47382) (60 g /tube - ref. No /93; H4738) or APV assembly grease for VMQ (Silicone) (0,6 kg /can - ref. No /93; H47380) (60 g /tube - ref. No /93; H47379)!!! Do not use grease containing mineral oil for EPDM seals!!!!!! Do not use Silicone-based grease for VMQ seals!!! Butterfly Valve DELTA SVSF DN Instruction Manual: UK - rev. 5 2

18 APV UK APV_SVSF _UK-5_08207.qxp 2. Service Instructions 2.. Dismantling from the line system!. Shut off line pressure and drain lines if possible. 2. Separate pneumatic air line from turning actuator. 3. Release clamp connection at support of proximity switches. Pull off proximity switch. 4. Remove the flange screws (8). 5. Take butterfly valve out of the flanges. 4 Attention! Disassembly from the line system in closed valve state, only! 2.2. Dismantling of the actuating device Design with pneumatic actuator: (spare parts lists RN ) Remove the two fastening screws (0) at the yoke (2). Lift off actuator (4) with yoke and coupling () to the top. Attention! If valve position indicators are installed, see to the position of the operating cam. - Design with manual actuation with limit switch: (spare parts lists RN ) or manual actuation with limit switch for valve position indication: (spare parts lists RN ) Remove the two fastening screws (2). Lift thrust piece (3), handle (4) and ratchet disc () off to the top Butterfly Valve DELTA SVSF DN Instruction Manual: UK - rev. 5

19 APV UK APV_SVSF _UK-5_08207.qxp 2. Service Instructions 2.3. Dismantling of inner parts seal ring, bearing bushes, valve disc - Remove all fastening screws (9) around the circumferences of the valve housing and extend the housing halves Replacement of seals. Lift the flange seals (4) out of the groove and replace them. Remove the fastening screws (9) from the valve core and part the housing halves. 2. Turn the disc (2) in the seal ring into open position. 3. Remove the bearing bushes (5) from the disc bolt. 4. By a slight pressing, the seal ring (6) is deformed in its longitudinal axis. Slide the seal ring over the short disc bolt and pull it off the disc via the long disc bolt. 5. Clean the valve disc (2) Installation of seals and bearing bushes fig. Attention! Use only those assembly greases being suited for the respective seal material. bearing bush. Provide the inner surfaces of the cross holes as well as the sealing surface and the disc bolts with a thin grease layer before installation of the parts (see chapter ). 2. Install the seal ring (6) via the long and, then, via the short disc bolt on the disc (2). fig. 2 wrong assembly 3. Slide the bearing bushes (5) on the disc bolts. The bearing bushes must be flush with the housing halves (fig. ). 4. Turn the valve disc in the seal ring into open position. 5. Insert the valve disc with seal ring and bearing bushes in one housing half. Fit the other housing half into it and tighten the assembly crosswise by means of the inner hexagon screws (9). Attention! When tightening the inner hexagon screws, the valve disc must be in open position. Damage to the valve disc seal is possible in case of installation in closed position. The bearing bushes must not protrude from the housing flange (fig. 2). 6. Fasten the mating flange (3) with the screws (8). Butterfly Valve DELTA SVSF DN Instruction Manual: UK - rev. 5 4

20 APV UK APV_SVSF _UK-5_08207.qxp 2. Service Instructions 2.6. Installation of the actuating device - Observe the steps mentioned in 0.2 in reverse order. - With manual butterfly valves, the disc and the handle are in a line. - Observe the required valve design NC or NO during the assembly of the turning actuator. NC = normally closed Valve disc is closed. Place the turning actuator with yoke and coupling on the valve and fasten the assembly with the screws (0). The upper operating cam must be adjusted to the upper yoke bore. NO = normally open Valve disc is open. Place the turning actuator with yoke and coupling on the valve and fasten the assembly with the screws (0). The lower operating cam must be adjusted to the lower yoke bore.! DANGER! After installation of the turning actuator do not touch the open valve! Risk of bruising at movable parts! Risk of injury by sudden valve operation! 2.7. Installation of feedback units turning actuator - Valve position indication OPEN: Installation of the feedback unit in the lower yoke bore. - Valve position indication CLOSED: Installation of the feedback unit in the upper yoke bore. - Insert proximity switch support into the yoke bore and fasten it. Introduce the proximity switch into the support until it stops and fix it with the clamp screw. yoke yoke bore 5 Butterfly Valve DELTA SVSF DN Instruction Manual: UK - rev. 5

21 APV UK APV_SVSF _UK-5_08207.qxp 3. Spare Parts Lists (see annex) The reference numbers of the spare parts for the different valve designs and sizes are included in the attached spare parts drawings with corresponding lists. Please indicate the following data to place an order for spare parts: - number of parts required - reference number - designation. subject to change Butterfly Valve DELTA SVSF DN Instruction Manual: UK - rev. 5 6

22

23 Weitergabe sowie Vervielfältigung dieser Unterlage, Verwertung und Mitteilung ihres Inhalts nicht gestattet, soweit nicht schriftlich zugestanden. Verstoß verpflichtet zum Schadensersatz und kann strafrechtliche Folgen haben (Paragraph 8 UWG, Paragraph 06 UrhG). Eigentum und alle Rechte, auch für Patenterteilung und Gebrauchsmustereintragung, vorbehalten. SPX FLOW, Germany Datum: Name: Trytko Ersatzteilliste: spare parts list Scheibenventil SVSF -FZ-CU Butterfly valve SVSF -A-CU DN S Blatt SPX FLOW Germany von 4 RN

24 Weitergabe sowie Vervielfältigung dieser Unterlage, Verwertung und Mitteilung ihres Inhalts nicht gestattet, soweit nicht schriftlich zugestanden. Verstoß verpflichtet zum Schadensersatz und kann strafrechtliche Folgen haben (Paragraph 8 UWG, Paragraph 06 UrhG). Eigentum und alle Rechte, auch für Patenterteilung und Gebrauchsmustereintragung, vorbehalten. SPX FLOW, Germany Ersatzteilliste: spare parts list Scheibenventil SVSF -FZ-CU Butterfly valve SVSF -A-CU DN S Datum: Name: Trytko Datum: Name: SPX FLOW Germany Blatt 2 von RN Dichtung SVSF Seal SVSF Skt. Mutter Hex. Nut Skt. Schraube Hex. Screw Zyl. Schraube Cyl. Screw Skt. Schraube Hex. Screw Beschreibung description DIN EN A2 DIN EN 2404-A2-70 DIN EN ISO 4762-A2-70 DIN EN 2407-A matt/satin fin. DN / / / /44 H0537 H0538 H0539 H / / / /43 H26403 H632 H64 H / / / /42 H8839 H8858 H886 H / / / / / / / /73 H77350 H77356 H0792 H / / / /33 H7236 H7237 H7238 H / / / /3 H77349 H77355 H /93 H / /93 H77605 H / /73 H07944 H / /33 H77200 H /3 H /3 2xM8x25 H7904 H77357 H77359 H /93 H / /93 H7764 H / /73 H07946 H / /33 H38439 H / / /3 H500 H49089 H /5 M8x6 H xM2 H xM2 H / /3 8xM2x0 H xM2x0 H Menge quantity item Klappe 2 Disc Gehäusehälfte SVSF -Schweißteil Housing Half SVSF -weld part Flansch FG Flange FG Dichtung FGN Seal FGN Dichtung FGN Seal FGN Dichtung FGN HNBR FDA-konform Seal FGN Dichtung FGN Seal FGN Lagerbuchse PA2 Bearing 30%GF Dichtung SVSF Seal SVSF Material material matt/satin fin. EPDM FDA-konform FPM FDA-konform VMQ FDA-konform Dichtung SVSF EPDM Seal SVSF FDA-konform FPM FDA-konform HNBR FDA-konform Dichtung SVSF VMQ Seal SVSF FDA-konform H /5 8xM0 H /3 8xM0x95 H / /3 4xM8x25 H /5 4

25 Weitergabe sowie Vervielfältigung dieser Unterlage, Verwertung und Mitteilung ihres Inhalts nicht gestattet, soweit nicht schriftlich zugestanden. Verstoß verpflichtet zum Schadensersatz und kann strafrechtliche Folgen haben (Paragraph 8 UWG, Paragraph 06 UrhG). Eigentum und alle Rechte, auch für Patenterteilung und Gebrauchsmustereintragung, vorbehalten. SPX FLOW, Germany Ersatzteilliste: spare parts list Scheibenventil SVSF -FZ-CU Butterfly valve SVSF -A-CU DN S Datum: Name: Trytko Datum: Name: Blatt SPX FLOW Germany 3 von 4 RN pos. Beschreibung item description material Menge quantity Initiatorhalter SV komplett Proximity switch holder SV complete Material Scheibe DIN 25 A8,4 Washer Drehantrieb für Rückmeldeeinheit 6 Actuator for conrtol unit 7 8 Drehantrieb Actuator Halter Holder Skt. Schraube Hex. Screw CU4-T-max-Adapter PA6.6 GF30 CU4-T-max-Adapter schwarz Control-Unit CU Control-Unit CU DIN EN 2407-A2-70 PA6.6 GF30 schwarz DN Kupplung / Coupling H05096 Laterne /7 2 Yoke H3376 Skt. Schraube /5 3 2 DIN EN 2407-A2-70 Hex. Screw M0x6 H /7 H /7 H /93 H32987 siehe Betriebsanleitung CU see manual CU /7 H /7 H /7 H /5 H /5 M8x0 H /5 H /7 H34034 SVSF ohne Drehantrieb ohne FG Flansche SVSF without actuator and FG flange SVSF ohne Drehantrieb ohne FG Flansche SVSF without actuator and FG flange SVSF ohne Drehantrieb ohne FG Flansche SVSF without actuator and FG flange SVSF ohne Drehantrieb ohne FG Flansche SVSF without actuator and FG flange EPDM matt-gl/satin fin FPM matt-gl/satin fin HNBR matt-gl/satin fin VMQ matt-gl/satin fin / / / /8 H0667 H06685 H06689 H / / / /7 H06670 H06688 H / / / / / / / /75

26 Weitergabe sowie Vervielfältigung dieser Unterlage, Verwertung und Mitteilung ihres Inhalts nicht gestattet, soweit nicht schriftlich zugestanden. Verstoß verpflichtet zum Schadensersatz und kann strafrechtliche Folgen haben (Paragraph 8 UWG, Paragraph 06 UrhG). Eigentum und alle Rechte, auch für Patenterteilung und Gebrauchsmustereintragung, vorbehalten. SPX FLOW, Germany Ersatzteilliste: spare parts list Datum: Name: Trytko Scheibenventil SVSF -FZ-CU Butterfly valve SVSF -A-CU DN S SPX FLOW Germany Datum: Blatt 4 von 4 Name: RN pos. item description material Beschreibung Material DN Menge quantity Drehantrieb mit Laterne+Kupplung Actuator with yoke and coupling /7 H /7 H32222 Pos. 4, 5, 6 nur im kompletten Dichtungssatz erhältlich Item 4, 5, 6 available as complete seal kits only Dichtungssatz FPM Seal kit Dichtungssatz EPDM Seal kit / / / /00 H34406 H36433 H36434 H / / / /0 H H H H Dichtungssatz / / / /02 HNBR Seal kit H3798 H32575 H H32539 Dichtungssatz / / / /06 VMQ Seal kit H36455 H36456 H H3762

27 Weitergabe sowie Vervielfältigung dieser Unterlage, Verwertung und Mitteilung ihres Inhalts nicht gestattet, soweit nicht schriftlich zugestanden. Verstoß verpflichtet zum Schadensersatz und kann strafrechtliche Folgen haben (Paragraph 8 UWG, Paragraph 06 UrhG). Eigentum und alle Rechte, auch für Patenterteilung und Gebrauchsmustereintragung, vorbehalten. SPX FLOW, Germany Datum: Name: Trytko C.Keil Ersatzteilliste: spare parts list Scheibenventil SVSF -Handbetätigung und Handbetätigung für Ventilstellungsmeldung Butterfly valve SVSF -handle and handle with position indicator DN S Blatt SPX FLOW Germany von 3 RN

28 Weitergabe sowie Vervielfältigung dieser Unterlage, Verwertung und Mitteilung ihres Inhalts nicht gestattet, soweit nicht schriftlich zugestanden. Verstoß verpflichtet zum Schadensersatz und kann strafrechtliche Folgen haben (Paragraph 8 UWG, Paragraph 06 UrhG). Eigentum und alle Rechte, auch für Patenterteilung und Gebrauchsmustereintragung, vorbehalten. SPX FLOW, Germany Ersatzteilliste: spare parts list Scheibenventil SVSF -Handbetätigung und Handbetätigung für Ventilstellungsmeldung Butterfly valve SVSF -handle and handle with position indicator DN S Datum: Name: Trytko Datum: Name: C.Keil Blatt 2 SPX FLOW Germany von RN item 2 Klappe 2 Disc Flansch FG Flange FG Dichtung FGN Seal FGN Dichtung FGN Seal FGN Seal FGN Dichtung FGN Seal FGN Material material matt/satin fin. EPDM FDA-konform FPM FDA-konform Dichtung FGN HNBR FDA-konform VMQ FDA-konform Lagerbuchse PA2 Bearing 30%GF Dichtung SVSF EPDM Seal SVSF FDA-konform Dichtung SVSF Seal SVSF Dichtung SVSF Seal SVSF Beschreibung description.4404 matt/satin fin. FPM FDA-konform Dichtung SVSF VMQ Seal SVSF FDA-konform / / / /44 H0537 H0538 H0539 H / / / /43 H26403 H632 H64 H / / / /42 H7735 H77357 H77359 H / / / /73 H77350 H77356 H0792 H / / / /33 H7236 H7237 H7238 H / / / /3 H / /93 H77605 H / /73 H07944 H / /33 H77200 H /3 H /5 8xM0 H /3 8xM0x95 H /3 2xM8x25 H /7 H5209 H / /93 H7764 H / / / /7 H /5 3 Menge quantity 7 9 Gehäusehälfte SVSF -Schweißteil Housing Half SVSF -weld part Skt. Mutter Hex. Nut Skt. Schraube Hex. Screw Zyl. Schraube Cyl. Screw Handbetätigung Handle DIN EN A2 DIN EN 2404-A2-70 DIN EN ISO 4762-A2-70 HNBR FDA-konform DN H8839 H8858 H886 H / / / / / /93 H77349 H77355 H77358 H07946 H / /33 H38439 H / / /3 H500 H49089 H xM2 H xM2 H / /3 8xM2x0 H xM2x0 H /3 4xM8x25 H7904

29 Weitergabe sowie Vervielfältigung dieser Unterlage, Verwertung und Mitteilung ihres Inhalts nicht gestattet, soweit nicht schriftlich zugestanden. Verstoß verpflichtet zum Schadensersatz und kann strafrechtliche Folgen haben (Paragraph 8 UWG, Paragraph 06 UrhG). Eigentum und alle Rechte, auch für Patenterteilung und Gebrauchsmustereintragung, vorbehalten. SPX FLOW, Germany Ersatzteilliste: spare parts list Scheibenventil SVSF -Handbetätigung und Handbetätigung für Ventilstellungsmeldung Butterfly valve SVSF -handle and handle with position indicator DN S Datum: Name: Trytko Datum: Name: C.Keil Blatt pos. Beschreibung Material item description material Menge quantity Handbetätigung für VSM Handle with position indicator DN /7 H /7 H05074 SVSF ohne Handbetätigung ohne FG Flansche SVSF without handle and FG flange SVSF ohne Handbetätigung ohne FG Flansche SVSF without handle and FG flange SVSF ohne Handbetätigung ohne FG Flansche SVSF without handle and FG flange SVSF SVSF ohne Handbetätigung ohne FG Flansche without handle and FG flange EPDM matt-gl/satin fin FPM matt-gl/satin fin HNBR matt-gl/satin fin VMQ matt-gl/satin fin / /8 H0667 H / /7 H / / / / / /8 H06689 H / /7 H06688 H / / / /75 Pos. 4, 5, 6 nur im kompletten Dichtungssatz erhältlich Item 4, 5, 6 available as complete seal kits only Dichtungssatz FPM Seal kit Dichtungssatz EPDM Seal kit / / /00 H34406 H36433 H /00 H / / / /0 H H H H / /02 H36455 H32575 Dichtungssatz / /02 HNBR Seal kit H H32539 Dichtungssatz / / / /06 VMQ Seal kit H3798 H36456 H H SPX FLOW Germany von 3 RN

30

31 Weitergabe sowie Vervielfältigung dieser Unterlage, Verwertung und Mitteilung ihres Inhalts nicht gestattet, soweit nicht schriftlich zugestanden. Verstoß verpflichtet zum Schadensersatz und kann strafrechtliche Folgen haben (Paragraph 8 UWG, Paragraph 06 UrhG). Eigentum und alle Rechte, auch für Patenterteilung und Gebrauchsmustereintragung, vorbehalten. SPX FLOW, Germany Datum: Name: Trytko Ersatzteilliste: spare parts list Handbetätigung mit Endlagenverriegelung und Handbetät. abschließbar für SVSF Handle with lockingdevice and handle lockable for batterfly valves SVSF DN Blatt SPX FLOW Germany von 2 RN

32 Weitergabe sowie Vervielfältigung dieser Unterlage, Verwertung und Mitteilung ihres Inhalts nicht gestattet, soweit nicht schriftlich zugestanden. Verstoß verpflichtet zum Schadensersatz und kann strafrechtliche Folgen haben (Paragraph 8 UWG, Paragraph 06 UrhG). Eigentum und alle Rechte, auch für Patenterteilung und Gebrauchsmustereintragung, vorbehalten. SPX FLOW, Germany Ersatzteilliste: spare parts list Handbetätigung mit Endlagenverriegelung und Handbetät. abschließbar für SVSF Handle with locking device and handle lockable for butterfly valves SVSF DN Datum: Name: Trytko Datum: Name: pos. Beschreibung description /7 SPX FLOW Germany Menge quantity item 2 3 Handbetätigung komplett Handle complete Handbetätigung abschließbar komplett Handle lockable complete Rasterscheibe Scale disc 5 Skt. Schraube DIN EN 2407-A2-70 Hex. Screw Druckstück Spacer Material material 4 Handhebel komplett Handle complete 5 2 Steckkerbstift Grooved pin DIN EN ISO 874-V2A Schwerspannstift Heavy duty dowel pin INOX Unterzange Lower tongs 7. Unterzange für Handbetätigung Abschließbar Lower tongs for manual actuation lockable 8 Druckfeder.430 Pressure spring DN25 DN50 DN200 DN /7 H /7 H /7 H /7 H /7 H /5 M8x2 H /3 0x24 H /3 S5x8 H79932 H /2 H /3 H /7 H /7 H /7 H /7 H /7 H5074 Blatt 2 von 2 RN

33 Weitergabe sowie Vervielfältigung dieser Unterlage, Verwertung und Mitteilung ihres Inhalts nicht gestattet, soweit nicht schriftlich zugestanden. Verstoß verpflichtet zum Schadensersatz und kann strafrechtliche Folgen haben (Paragraph 8 UWG, Paragraph 06 UrhG). Eigentum und alle Rechte, auch für Patenterteilung und Gebrauchsmustereintragung, vorbehalten. SPX FLOW, Germany Datum: Name: Trytko Ersatzteilliste: spare parts list Handbetätigung mit Endlagenverriegelung für Ventilstellungsmeldung SVSF Handle with lockingdevice for valve position indicator for batterfly valves SVSF DN Blatt SPX FLOW Germany von 2 RN

34 Weitergabe sowie Vervielfältigung dieser Unterlage, Verwertung und Mitteilung ihres Inhalts nicht gestattet, soweit nicht schriftlich zugestanden. Verstoß verpflichtet zum Schadensersatz und kann strafrechtliche Folgen haben (Paragraph 8 UWG, Paragraph 06 UrhG). Eigentum und alle Rechte, auch für Patenterteilung und Gebrauchsmustereintragung, vorbehalten. SPX FLOW, Germany Ersatzteilliste: spare parts list Handbetätigung mit Endlagenverriegelung für Ventilstellungsmeldung SVSF Handle with locking device for valve position indicator for butterfly valves SVSF DN Datum: Name: Trytko Datum: Name: pos. Beschreibung description /3 H78352 SPX FLOW Germany Menge quantity item Handbetätigung mit VSM komplett Handle with position indicator complete DN25 DN50 DN200 DN250 Rasterscheibe Scale disc 2 5 Skt. Schraube /5 DIN EN 2407-A2-70 Hex. Screw M8x2 H Druckstück / /7 Spacer H5327 H Handhebel komplett / /7 Handle complete H05075 H Steckkerbstift /3 DIN EN ISO 874-V2A.4305 Grooved pin 0x24 H Schwerspannstift Heavy duty dowel pin INOX Unterzange Lower tongs 8 Druckfeder Pressure spring Material material /7 H /7 H /3 S5x8 H /7 H /7 H /7 H05058 Blatt 2 von 2 RN

35 Weitergabe sowie Vervielfältigung dieser Unterlage, Verwertung und Mitteilung ihres Inhalts nicht gestattet, soweit nicht schriftlich zugestanden. Verstoß verpflichtet zum Schadensersatz und kann strafrechtliche Folgen haben (Paragraph 8 UWG, Paragraph 06 UrhG). Eigentum und alle Rechte, auch für Patenterteilung und Gebrauchsmustereintragung, vorbehalten. SPX FLOW, Germany Ersatzteilliste: spare parts list Datum: Name: Trytko Trytko Drehantrieb K080, K25, K80 F/L Actuator K080, K25, K80 spring/air Name: Goebel SPX FLOW Germany Datum: Blatt von RN DRAT K080 DRAT K25 DRAT K80 2

36 Weitergabe sowie Vervielfältigung dieser Unterlage, Verwertung und Mitteilung ihres Inhalts nicht gestattet, soweit nicht schriftlich zugestanden. Verstoß verpflichtet zum Schadensersatz und kann strafrechtliche Folgen haben (Paragraph 8 UWG, Paragraph 06 UrhG). Eigentum und alle Rechte, auch für Patenterteilung und Gebrauchsmustereintragung, vorbehalten. SPX FLOW, Germany Ersatzteilliste: spare parts list Datum: Name: Trytko Trytko Drehantrieb K080, K25, K80 F/L Actuator K080, K25, K80 spring/air Goebel Datum: Name: SPX FLOW Germany Blatt 2 von 2 RN pos. Beschreibung Material item description material / / /7 H05500 H05502 H / / /3 H3599 H3940 H / / /7 H05499 H0550 H / / /3 H3494 H3502 H / / /3 H3493 H350 H /83 32,2x3 H /34 H /93 H /73 49,5x3 H /63 H3684 Menge quantity Drehantrieb komplett Actuator complete Drehantrieb komplett Actuator complete Drehantrieb Schweißteil Actuator welded Spindel komplett mit Lager Shaft complete with bearing Spindel Shaft Winkelverschraubung G/8" schwenkbar Elbow union G/8" slewable O-Ring O-ring matt-glänzend poliert Polyamid/ Glasf O-Ring NBR O-ring FPM Lager für Drehantrieb POM Bearing for actuator Lager für Drehantrieb PA2 Bearing for actuator Stellring Adjust ring K080 K25 K /3 H /3 H79758 Zyl. Kerbstift / /3 DIN EN ISO 8740-V2A.4305 Cyl. pin 5x26 H7996 8x45 H7997

37 Weitergabe sowie Vervielfältigung dieser Unterlage, Verwertung und Mitteilung ihres Inhalts nicht gestattet, soweit nicht schriftlich zugestanden. Verstoß verpflichtet zum Schadensersatz und kann strafrechtliche Folgen haben (Paragraph 8 UWG, Paragraph 06 UrhG). Eigentum und alle Rechte, auch für Patenterteilung und Gebrauchsmustereintragung, vorbehalten. SPX FLOW, Germany Ersatzteilliste: spare parts list Datum: Name: Trytko Trytko Drehantrieb K080, K25, K80 F/L für Rückmeldeeinheit Actuator K080, K25, K80 spring/air for control unit Name: SPX Flow Technology Rosista GmbH D Unna Germany Datum: Blatt von RN

38 Weitergabe sowie Vervielfältigung dieser Unterlage, Verwertung und Mitteilung ihres Inhalts nicht gestattet, soweit nicht schriftlich zugestanden. Verstoß verpflichtet zum Schadensersatz und kann strafrechtliche Folgen haben (Paragraph 8 UWG, Paragraph 06 UrhG). Eigentum und alle Rechte, auch für Patenterteilung und Gebrauchsmustereintragung, vorbehalten. SPX FLOW, Germany Ersatzteilliste: spare parts list Datum: Name: Trytko Trytko Drehantrieb K080, K25, K80 F/L für Rückmeldeeinheit Actuator K080, K25, K80 spring/air for control unit Datum: Name: SPX FLOW Germany Blatt 2 von 2 RN pos. item description material Drehantrieb komplett Actuator complete Drehantrieb komplett Actuator complete Drehantrieb Schweißteil Actuator welded Spindel komplett mit Lager Shaft complete with bearing O-Ring O-ring OR 32,3x3 NBR O-Ring O-ring OR 49,5x3 FPM Lager für Drehantrieb Bearing for actuator POM Lager für Drehantrieb PA2 Bearing for actuator Stellring Adjust ring 6 Zyl. Kerbstift Cyl. pin DIN EN ISO 8740-V2A O-Ring O-ring OR 90x2 NBR 8 O-Ring O-ring OR 5,3x2,4 NBR 9 Druckstück Drehantrieb Thrust ring turning actuator Hostaform K080 K25 K / / /7 H23937 H28942 H / / /3 H36969 H H / / /7 H23936 H28940 H / / /3 H3494 H3502 H / / /3 H3493 H350 H /83 H76965 Menge quantity Spindel Shaft Beschreibung Material matt-glänzend poliert /34 H /3 5x26 H /83 H /53 H /83 H /73 H /63 H / /3 H79757 H /3 8x45 H7997

39

40 APV DELTA SVSF DN BUTTERFLY VALVE SPX FLOW SPX FLOW Design Center Production Gottlieb-Daimler-Straße 3 Stefana Rolbieskiego 2 D Holzwickede, Germany PL- Bydgoszcz , Poland P: (+49) (0) P: (+48) F: (+49) (0) F: (+48) SPX FLOW reserves the right to incorporate the latest design and material changes without notice or obligation. Design features, materials of construction and dimensional data, as described in this manual, are provided for your information only and should not be relied upon unless confirmed in writing. Please contact your local sales representative for product availability in your region. For more information visit Scan for SV/SVSF Valve Maintenance Video ISSUED 08/207 - Translation of Original Manual COPYRIGHT 207 SPX FLOW, Inc.