APV DELTA RGMS4 INSTRUCTION MANUAL MODULATING VALVE WITH PRODUCT DIAPHRAGM FAN SUPPORT (ASEPTIC)

Transcription

1 INSTRUCTION MANUAL APV DELTA RGMS4 MODULATING VALVE WITH PRODUCT DIAPHRAGM FAN SUPPORT (ASEPTIC) FORM NO.: H REVISION: UK- READ AND UNDERSTAND THIS MANUAL PRIOR TO OPERATING OR SERVICING THIS PRODUCT.

2

3 UK EU Declaration of Conformity for Valves and Valve Manifolds SPX Flow Technology Germany GmbH Gottlieb-Daimler-Str. 3, D Holzwickede herewith declares that the APV double seal and double seat valves of the series SD4, SDT4, SDU4, SDMS4, SDMSU4, SDTMS4, SWcip4, DSV, DA4, D4 SL, D4, DA3, DA3SLD, DE3, DEU3, DET3, DKR2, DKRT2, DKRH2 in the nominal diameters DN 25-50, ISO 6 and Sh5-6 Sh5 APV butterfly valves of the series SV and SVSF, SVL and SVSL in the nominal diameters DN 25-00, DN and ISO 4 APV ball valves of the series KHI, KHV in the nominal diameters DN 5-00 APV single seat, diaphragm and spring loaded valves of the series S2, SW4, SWhp4, SW4DPF, SWmini4, SWT4, SWS4, MF4, MS4, MSP4, AP/T, CPV, RG4, RG4DPF, RGMS4, RGE4, RGE4DPF, RGEMS4, PR2, PRD2, SI2, UF/R3, VRA/H in the nominal diameters DN 0-50, ISO /2 4 and Sh5-6 Sh5 and the valve manifolds installed thereof meet the requirements of the Directives 2006/42/EC (superseding 89/392/EEC and 98/37/EC) and ProdSG (superseding GPSG - 9.GPSGV). For official inspections, SPX FLOW presents a technical documentation according to Appendix VII of the Machinery Directive, this documentation consisting of documents of the development and construction, description of measures taken to meet the conformity and to correspond with the basic requirements on safety and health, incl. an analysis of the risks, as well as an operating manual with safety instructions. The conformity of the valves and valve manifolds is guaranteed. Authorised person for the documentation: Frank Baumbach SPX Flow Technology Germany GmbH Gottlieb-Daimler-Str. 3, D Holzwickede, Germany May 208 Frank Baumbach Regional Engineering Manager, F&B Components

4

5 APV UK APV_RGMS4_UK-_208.qxp Table of Contents Page. General Information 2 2. Safety Instructions 2 3. Intended Use 3 4. Mode of Operation General Information 4.2. Actuator 5. Installation 5 5. Welding Instructions 6. Dimensions / Weights Integrated positioner DN 6.2. Integrated positioner Inch 6.3. Positioner according to NAMUR DN 6.4. Positioner according to NAMUR Inc 7. Technical Data General Information 7.2. Specification of compressed air quality 7.3. Kvs values in m³/h 8. Materials 2 9. Maintenance 3 0. Service Instructions - Single seat valve Dismantling from the line system 0.2. Dismantling of valve to replace wear parts 0.3. Dismantling of valve to modify kvs values or characteristics 0.4. Assembly of valve and installation of new wear parts 0.5. Assembly of valve to modify kvs values or characteristics. Trouble Shooting 8 2. Spare Parts Lists 9 3. Replacement Parts List 9 RGMS4 - DN design RN RGMS4 - Inch design RN (-) Modulating valve with product diaphragm DELTA RGMS4 - MFS + MFH 3A Instruction manual: rev.

6

7 APV UK APV_RGMS4_UK-_208.qxp. General Information This instruction manual should be read carefully by the competent operating and maintenance personnel. We point out that we will not accept any liability for damage or malfunctions resulting from the non-compliance with this operating manual. Descriptions and data given herein are subject to technical changes. 2. Safety Instructions!!! DANGER! - The technical safety symbol draws your attention to important directions of operating safety. You will find it wherever the activities described are bearing risks of personal injury. - Depressurize and, if possible, discharge the line and cleaning system before any maintenance work. - Do not touch the yoke area or actuating area (positioner) when the valve is installed. Risk of injury through sudden valve operation. - Electric and pneumatic lines must be disconnected before assembly or disassembly of the valve (e.g. for seal replacement). - Do not reach into the valve body when the valve is dismantled. Observe instructions given for valve in installed state. - In case of damage of the diaphragm, fluids will leak from the leakage bore in the yoke area.! - Attention: Risk of burn To prevent personal injury, the valves must not be touched during CIP cleaning or sterilization with hot water or steam. - Observe Service Instructions to ensure safe maintenance of the valve. The valve must only be assembled, disassembled and reassembled by persons who have been trained in APV valves or by SPX FLOW service team members. If necessary, contact your local SPX FLOW representative. Modulating valve with product diaphragm DELTA RGMS4 - MFS + MFH 3A Instruction manual: rev. 2

8 APV UK APV_RGMS4_UK-_208.qxp 3. Intended Use The intended use as field of application of the APV DELTA RGMS4 aseptic modulating valve is the flow and pressure control of liquids and gases. Arbitrary, constructive changes at the valve will influence safety as well as the intended functionality of the valve and are not permissible. Authorizations and External Evaluations To view the certifications for this and other innovative SPX FLOW products, visit fig. RGMS4 4. Mode of Operation 4.. General Information - Aseptic modulating valves RGMS4 can be used for the continuous regulation of flows in the beverage and food industries and in chemical and pharmaceutical applications. D - The modulating valves are suited for the flow and pressure regulation of fluids and gases. C - An optimum protection of the product in hygienic and aseptic areas is guaranteed. G - At the shaft passages product safety is reached by the hermetic separation of the product chamber from the outside (atmosphere) by a flexible diaphragm. yoke E - In its basic shape, the Delta RGM4 is designed as a corner valve. Therefore, the valve proves favourable flow deviation characteristics. The flow direction is from A to B (fig. ). diaphragm support L - The housing which is free of dead spaces has optimum cleaning features. Crevice-free sealing of the individual housing parts by profile seals - no source of infection. B - Leakages at the membrane are indicated in the yoke area via a leakage drain (L). valve seat A diaphragm valve cone - The interdependence between flow and cone stroke is defined by the characteristics. - Different kvs values (flow) with a certain valve dimension can be reached by different inserts (valve seat / valve cone). (fig. ) - The table in Item 2. shows the parts to be changed in case of modification of the kvs value. - The connections (C) or the electric and pneumatic supply are located laterally at the positioner (G). - An optical position indication (stroke indication) is located in the yoke area (E). 3 Modulating valve with product diaphragm DELTA RGMS4 - MFS + MFH 3A Instruction manual: rev.

9 APV UK APV_RGMS4_UK-_208.qxp 4. Mode of Operation fig. 2 fig. 3 integrated installation of positioner installation of positioner according to NAMUR 4.2. Actuator - The pneumatic actuator (D) provides the path and the force to open or to close the control element. The diaphragm actuator is suited for longer actuating distances at minimum self-friction. The valve positioner (C) guarantees the preset coordination between valve position and control signal. It compares the control signal (4-20 ma) given by the control device with the stroke of the control element and defines the pneumatic actuating pressure as output signal. - Depending on the specific requirement, the modulating valve can be operated either in normally open or in normally closed design. MFS - diaphragm actuator normally closed The actuator opens with actuating pressure and closes by spring pressure. MFH - diaphragm actuator normally open The actuator closes with actuating pressure and opens by spring pressure. - For the various applications, the diaphragm actuators are supplied with different actuating pressures. - In its standard design, the valve positioner is an electro-pneumatic transformer. A pneumatic valve positioner is also available for specific operations. The direction of flows transferred can be rising (directional equality >>) or falling (directional reverse <>). - The valve positioner can be installed in two different ways: ) valve positioner is integrated in the diphragm actuator; The feedback of the valve position is effected as mechanical tap at the valve shaft within the integrated positioner (fig. 2). 2) valve positioner according to NAMUR; The positioner is installed at the valve yoke by means of a rib. The feedback of the valve position is effected via the operating cam with fastening plate installed at the valve shaft (fig. 3). - Valve position indication can also be in the positioner; either by indication of the valve final position or by an analog feedback for the whole stroke range. Modulating valve with product diaphragm DELTA RGMS4 - MFS + MFH 3A Instruction manual: rev. 4

10 APV UK APV_RGMS4_UK-_208.qxp 5. Installation - The Delta RGMS4 valve must be installed in such a way that products and cleaning liquids can drain off the valve housing. Priority should be given to a vertical installation. - Attention: Observe welding instructions! 5. Welding Instructions RGMS4 - Before welding of the valve, the complete valve insert must be dismantled from the housing. Careful handling to avoid damage to the parts is necessary. - Dismantle the mating flanges from the valve housing and remove the flange seals. Just tacking or adjustment of the mating flanges should be undertaken with fixed valve housing. - Welding should only be carried out by certified welders (DIN EN ISO 9606-). (seam quality DIN EN ISO 587) - The preparation of the weld seam up to 3 mm thickness shall be carried out as a square butt joint without air. (Consider shrinkage!) - TIG orbital welding is best! - After welding of the valve housing or of the mating flanges and after work at the pipelines, the corresponding parts of the installation and pipelines must be cleaned from welding residues and soiling. If these cleaning instructions are not observed, welding residues and dirt particles can settle in the valve and cause damage. - Any damage resulting from the non-obeservance of these welding instructions is not subject of our guarantee. 5 Modulating valve with product diaphragm DELTA RGMS4 - MFS + MFH 3A Instruction manual: rev.

11 APV UK APV_RGMS4_UK-_208.qxp 6. Dimensions / Weights 6. Integrated positioner (DN - metric dimensions) E B D A C K L dimensions in mm F DN actuating surface (cm2) L A B C Ø D F Ø E K weight in kg ,7 89,5 55, , , ,5 6, , , , 204,0 70, , ,2 28,5 77, , , ,7 87, , ,7 Modulating valve with product diaphragm DELTA RGMS4 - MFS + MFH 3A Instruction manual: rev. 6

12 APV UK APV_RGMS4_UK-_208.qxp 6. Dimensions / Weights E 6.2 Integrated positioner (Inch) dimensions B D A C K L dimensions in mm F Inch,5 2 2,5 3 4 actuating surface (cm2) L A B C Ø D F Ø E K weight in kg , ,7 87,9 53,9 34, , , 20 42, , ,6 94,3 60,3 0 47, , , , , , 20,2 67,2 0 60, , , , ,2 207,5 73,5 0 72, , , ,6 226, ,7 85,8 0 97, ,6 242, ,7 7 Modulating valve with product diaphragm DELTA RGMS4 - MFS + MFH 3A Instruction manual: rev.

13 APV UK APV_RGMS4_UK-_208.qxp 6. Dimensions / Weights 6.3 Installation of positioner according to NAMUR (DN - metric dimensions) E D B A K L F dimensions in mm DN actuating surface (cm2) L A B Ø D F Ø E K weight in kg ,7 89,5 55, , , ,5 6, , , , 204,0 70, , ,2 28,5 77, , , ,7 87, , ,7 Modulating valve with product diaphragm DELTA RGMS4 - MFS + MFH 3A Instruction manual: rev. 8

14 APV UK APV_RGMS4_UK-_208.qxp 6. Dimensions / Weights 6.4 Installation of positioner according to NAMUR (Inch dimensions) E D B A K L F dimensions in mm Inch,5 2 2,5 3 4 actuating surface (cm2) L A B Ø D F Ø E K weight in kg 20 30, ,7 87,9 53,9 34, , , , , ,6 94,3 60,3 47, , , , , , 20,2 67,2 60, , , , ,2 207,5 73,5 72, , , ,6 226, ,7 85,8 97, ,6 242, ,7 9 Modulating valve with product diaphragm DELTA RGMS4 - MFS + MFH 3A Instruction manual: rev.

15 APV UK APV_RGMS4_UK-_208.qxp 7. Technical Data 7. General Information - permissible operating pressure inlet pressure p = 6 bar (in front of valve seat) outlet pressure p2 = 0 bar (in housing, on diaphragm) - correcting ratio: : 50 - max. operating temperature: 35 o C EPDM, HNBR * VMQ, * FPM - short-term load: 40 o C EPDM, HNBR * VMQ, * FPM * (no steam) - leakage indication in the yoke area: G/8 - actuating pressure of diaphragm actuator: max. 6 bar (min. 0,4 bar above actuating pressure, e.g. 0,6-3 bar * min.: 3,4 bar) - command variable of electro-pneumatic positioner: 4-20 ma - command variable of pneumatic positioner: 0,2 - bar 7.2 Specification of compressed air compressed air quality: quality class according to DIN ISO content of solid particles: quality class 3 max. size of solid particles per m³ 0000 of 0,5 µm < d <,0µm 500 of,0 µm < d < 5,0 µm content of water: quality class 3 max. dew point temperature -20 C For installations at lower temperatures or at higher altitudes, additional measures must be considered to reduce the pressure dew point accordingly. content of oil: quality class max. 0,0mg/m³ The oil applied must be compatible with Polyurethane elastomer materials. Modulating valve with product diaphragm DELTA RGMS4 - MFS + MFH 3A Instruction manual: rev. 0

16 APV UK APV_RGMS4_UK-_208.qxp 7. Technical Data 7.3. Kvs - values in m ³ /h DN40 DN 50 DN 65 DN 80 DN 00 stroke 5 mm stroke 5 mm stroke 5 mm stroke 5 mm stroke 5 mm Kvs S Ø Kvs S Ø Kvs S Ø Kvs S Ø Kvs S Ø , , ,5 6, ,5 2 2,5 3 4 stroke 5 mm stroke 5 mm stroke 5 mm stroke 5 mm stroke 5 mm Kvs S Ø Kvs S Ø Kvs S Ø Kvs S Ø Kvs S Ø , , , ,5 6, kvs = values in m³/h S Ø = seat diameter in mm Modulating valve with product diaphragm DELTA RGMS4 - MFS + MFH 3A Instruction manual: rev.

17 APV UK APV_RGMS4_UK-_208.qxp 8. Materials DELTA RGMS4 For the 3-A- design, the following two surface finishes are available: - valve shaft valve seat, flange Materials satin polished satin finish 36L,.4404 (DIN EN 0088) - housing 36L,.440 (DIN EN 0088) standard design: inside surface polished Ra < 0,8µm outside surface satin - valve yoke.4308 (DIN EN 0088) - coupling (compl.) screws, nuts.430 (DIN EN 0088) - flat diaphragm TFM (shaft passage) - housing seal standard: EPDM option: HNBR, VMQ, FPM - seat seal, FGN seal standard: EPDM option: HNBR, VMQ, FPM - type label PVC adhesive Diaphragm actuator - diaphragm shells sheet steel or aluminium diecasting plastic coated - rolling diaphragm NBR or EPDM with fabric insert - connecting rod, intermediate piece.430(din EN 0088) - springs.250 or.702 plastic coated Valve positioner - housing aluminium diecasting plastic coated or plastic - external parts.430 and.404 (DIN EN 0088) Modulating valve with product diaphragm DELTA RGMS4 - MFS + MFH 3A Instruction manual: rev. 2

18 APV UK APV_RGMS4_UK-_208.qxp 9. Maintenance Maintenance intervals depend on the application and must be decided by the operator himself carrying out regular checks. - The valve must not be cleaned with products containing abrasive or polishing material. Especially the valve shaft must not, under any circumstances, be cleaned with such agents. Damage of the valve shaft can lead to leakages. - The customer is recommended to hold spare seals and diaphragm on stock. For valve maintenance SPX FLOW supplies complete seal kits (pl. see spare parts lists) - Required tools: x spanner SW3 x spanner SW7 x spanner SW9 x spanner SW24 x spanner SW30 (.5") x screw driver small and medium - If damaged seals are dismantled, generally all seals and the diaphragm should be replaced. - Assembly and disassembly as well as replacement of seals / diaphragm, see Service Instructions. - Provide all seals with a thin layer of grease before their installation. Recommendation: APV assembly grease for EPDM, HNBR and FPM (0.75 kg /tin - ref.-no /93; H47382) (60 g /tube - ref.-no /93; H4738) or APV assembly grease for VMQ (0.6 kg /tin - ref.-no /93; H47380) (60 g /tube - ref.-no /93; H47379)! Do not use grease on mineral oil basis for EPDM seals.! Do not use Silicone-based grease for VMQ seals.! No matter what type of application, use only those greases being suited for the respective seal material. Recommendation for screw retention Type: Loctite 243 semi-solid (50 ml - ref.-no /93; H206336) 3 Modulating valve with product diaphragm DELTA RGMS4 - MFS + MFH 3A Instruction manual: rev.

19 APV UK APV_RGMS4_UK-_208.qxp 0. Service Instructions 0.. Disassembly from the line system RGMS4 The item numbers refer to the spare parts drawings. RGMS4 : DN design RN A- Inch design RN (-). Shut off line pressure and discharge lines if possible. 2. Shut off and disconnect air control line. 3. Shut off control power and disconnect connecting lines. 4. Loosen fastening screws (9) and take the valve insert with positioner and diaphragm actuator out of the housing (). 5. Loosen hex. screws (6) and nuts (7) of lateral flange connection. 6. Release hex. screws (4) of the lower flange/housing connection. 7. Remove housing from the line. Modulating valve with product diaphragm DELTA RGMS4 - MFS + MFH 3A Instruction manual: rev. 4

20 APV UK APV_RGMS4_UK-_208.qxp 0. Service Instructions 0.2. Disassembly of valve to replace wear parts fig. 9. See chapter 0., items Remove the valve seat (27/27.) from the housing (). 3. Remove the housing seals (8) and flange seals (3). adjusting dimension coupling head counter nut 4. Release the coupling between actuator rod and valve shaft. 5. Release the coupling head (29) and counternut (22) from the upper valve shaft (3). Note: Observe adjusting dimension between counternut and valve shaft (see fig. 9). 6. Pull the valve shaft with diaphragm (5), fan (6) and diaphragm support (7) out of the yoke (2). 7. Clamp the upper valve shaft (3) with the key surface in a vice (Attention: Use protective chops!) and release the lower valve shaft (25). Remove Loctite residues from the thread and thread bore. upper valve shaft 8. Remove the diaphragm (5) and fan (6) from the upper valve shaft. Remove the o-ring (8) from the fan. 9. Remove the seat seal (26) from the lower valve shaft (25). 0. Remove the o-rings (4, ) and guide bush (0) from the yoke (2) Disassembly of valve to modify kvs values or characteristics. See chapter 0., items See chapter 0.2, items If a replacement of the diaphragm actuator (30) is required for the modification of the kvs value, remove the air hose (9) and remove the nut and actuator if necessary. 5 Modulating valve with product diaphragm DELTA RGMS4 - MFS + MFH 3A Instruction manual: rev.

21 APV UK APV_RGMS4_UK-_208.qxp 0. Service Instructions guide bush 0.4. Assembly of valve and installation of new wear parts o-ring Attention! To provide for an easy assembly and an increased lifetime of all wear parts (seals, guide bushes, o-ring, etc.), the parts must be slightly greased. The diaphragm is greased on the product-averted side. Do not use sharp-edged tools for the assembly of the a.m. wear parts to guarantee their full function. o-ring. Install the housing seal (8) on the valve seat (27/27.) and insert both into the housing (). diaphragm support 2. Insert the flange seals (3) into the housing flange and insert the flange (5) and install the housing () by means of the screws and nuts (4, 6, 7) in the line system. Attention! Provide for proper alignment of the housing to the line flanges. 3. Install the seat seal (26) on the lower valve shaft (25). o-ring lower shaft upper shaft fan diaphragm Apply screw locker in threaded bore. Attention! To prevent air from being included in the groove, use a suitable tool to vent the groove. 4. Clamp the key surface of the upper valve shaft (3) into a vice. Insert the o-ring (8) in the fan. Place the diaphragm (5) and press it into the groove. Secure the lower valve shaft (25) with a drop of the screw retention (e.g. type: Loctite semi-solid). Apply the adhesive only in the threaded bore. Do not apply it in the thread of the upper shaft (fig. 9.4). Fasten the lower valve shaft with the upper valve shaft. 5. Insert the diaphragm support (7) in the fan.! Toothing of fan and diaphragm support must interlock. 6. Insert the guide bush (0) and o-ring (, 4) in the yoke (2). 7. Introduce the preassembled valve shaft in the yoke. The upper shaft must be guided smoothly through the guide bush into the yoke. In case of stiffness, check the even fit of the guide bush. seat seal Modulating valve with product diaphragm DELTA RGMS4 - MFS + MFH 3A Instruction manual: rev. 6

22 APV UK APV_RGMS4_UK-_208.qxp 0. Service Instructions fig Assembly of valve and installation of new wear parts 8. Screw the counternut (22)and coupling head (29) on the thread of the upper valve shaft (3).! Observe the adjusting dimension. adjusting dimension 9. Connect the valve shaft and the actuator rod of the diaphragm actuator by means of the coupling. (With NAMUR installation, slide the carrier pin of the positioner into the fastening plate.) Attention! (for NAUMUR installation) The position of the positioner to the fastening plate is different with the different functionalities of the diaphragm actuator (MFS or MFH). upper valve shaft 0. Press the valve insert into the housing and fasten it at the housing flange by means of the hex. screws (9).. Tighten the coupling. 2. Connect electric and pneumatic lines Assembly of valve to modify kvs values or characteristics Parts to be replaced - please see spare parts lists.. Make a functional check of the available wear parts (seals, o-ring and guide bush). Damaged parts must be replaced immediately. (designation and ref.-no.; see spare parts lists, chapter ) 2. To replace the diaphragm actuator: Place the diaphragm actuator (30) on the valve yoke (2) and turn the nut on the thread. Fasten it with hammer and chisel. 3. See chapter 0.4, items Check the function of the positioner and readjust it if necessary. 7 Modulating valve with product diaphragm DELTA RGMS4 - MFS + MFH 3A Instruction manual: rev.

23 APV UK APV_RGMS4_UK-_208.qxp. Trouble Shooting Failure Remedy Leakage between upper housing flange and yoke flange. Replace diaphragm (5) and o-ring (4, 8). Leakage from the leakage drain in the yoke area. Replace diaphragm (5) and o-rings (4, 8). Leakage between lower housing flange and mating flange. Replace housing seal (8) flange seal (3). Leakage at the lateral flange connection. Replace flange seal (3). Air escapes at the diaphragm actuator. Check threaded connections, replace rolling diaphragm if necessary. Air escapes at the air connections. Check reducer and air connections. Seal or replace parts if necessary. Valve does not regulate correctly. Check air connection and air pressure. Check electric connection and control signal. Use operating manual of positioner to find failure.! If damaged seals are changed, generally all seals should be replaced. For the valve service complete sets of seals are available (see spare parts lists). Modulating valve with product diaphragm DELTA RGMS4 - MFS + MFH 3A Instruction manual: rev. 8

24 APV UK APV_RGMS4_UK-_208.qxp 2. Spare Parts Lists The reference numbers of spare parts for the different valve designs and sizes are included in the attached spare parts drawings with corresponding lists. When you place an order for spare parts, please indicate the following data: - number of parts required - reference number - parts designation 3. Replacement Parts List Replacement parts are required in case of modification of the kvs values of the DELTA RGMS4 valve. The required component parts are described in the replacement parts list. Data are subject to change without notice. 9 Modulating valve with product diaphragm DELTA RGMS4 - MFS + MFH 3A Instruction manual: rev.

25 Weitergabe sowie Vervielfältigung dieser Unterlage, Verwertung und Mitteilung ihres Inhalts nicht gestattet, soweit nicht schriftlich zugestanden. Verstoß verpflichtet zum Schadensersatz und kann strafrechtliche Folgen haben (Paragraph 8 UWG, Paragraph 06 UrhG). Eigentum und alle Rechte, auch für Patenterteilung und Gebrauchsmustereintragung, vorbehalten. SPX FLOW, Germany Datum: Name: Trytko Trytko Trytko Knöchel Trytko Trytko Ersatzteilliste: spare parts list Regelventil RGMS4-DN25-00 Antrieb MAT3277 (MFS o. MFH) 20,240,350 cm² el-pneum. oder pneum. Stellungsregler; lineare oder gleichproz. Kennlinie Modulating valve RGMS4- DN with diaphragm actuator MAT3277 (spring: closed or open) 20,240,350 cm² el.-pneum. positioner; flow characteristics: linear and equal percentage Blatt SPX FLOW Germany von 9 RN

26 Weitergabe sowie Vervielfältigung dieser Unterlage, Verwertung und Mitteilung ihres Inhalts nicht gestattet, soweit nicht schriftlich zugestanden. Verstoß verpflichtet zum Schadensersatz und kann strafrechtliche Folgen haben (Paragraph 8 UWG, Paragraph 06 UrhG). Eigentum und alle Rechte, auch für Patenterteilung und Gebrauchsmustereintragung, vorbehalten. SPX FLOW, Germany Ersatzteilliste: spare parts list Regelventil RGMS4- DN25-00 Antrieb MAT3277 (MFS o.mfh) 20,240,350 cm² el-pneum. oder pneum. Stellungsregler; lineare oder gleichproz. Kennlinie Modulating valve RGMS4- DN25-00 with diaphragm actuator MAT3277 (spring: closed or open) 20,240,350 cm² el.-pneum. or pneum. positioner; flow characteristics: linear and equal percentage Datum: Name: Trytko Knöchel Datum: Name: Trytko Trytko Trytko Trytko SPX FLOW Germany Blatt 2 von 9 RN pos. item Beschreibung description Material material EPDM DN25 DN40 DN50 DN65 WS-Nr. WS-Nr. WS-Nr. WS-Nr. WS-Nr. WS-Nr. ref.-no. ref.-no. ref.-no. ref.-no. ref.-no. ref.-no. 3A /43 3A /43 3A /43 3A /43 3A /43 3A /43 H3287 H H H A /47 3A /47 3A /47 3A /47 3A /47 3A /47 H H32625 H3288 H32597 H H A /43 3A /43 3A /43 3A /43 3A /43 3A / / / / / / /47 H5802 H H77280 H77292 H77303 H Dichtung FGN FPM / / / / / /73 2 seal FGN H77279 H7729 H77302 H7733 H77324 H77338 Dichtung FGN HNBR / / / / / /33 2 seal FGN H7230 H723 H7232 H7233 H7234 H Dichtung FGN VMQ / / / / / /3 seal FGN H77278 H77290 H7730 H7233 H77323 H Skt. Schraube / / / /5 DIN EN 2407-A Hex. Screw 4xM8x8 H xM8x20 H xM0x20 H xM0x20 H Flansch FNX Ausführung 3A-blank 3A /43 3A /43 3A /43 3A /43 3A /43 3A / Flange FNX design 3A-bright finish Flansch FNX Ausführ. matt-glänzend / / / / / / Flange FNX design satin finish H58095 H58096 H58097 H58098 H58099 H Skt. Schraube / /5 DIN EN 2407-A Hex. screw 4xM8x28 H xM8x28 H Skt. Mutter / /5 DIN EN ISO 05-A2.430 Hex. Nut 4x M8 H7928 8x M8 H7928 Gehäusedichtung EPDM / / / / / /93 Housing seal H77439 H77464 H77488 H7752 H77543 H Gehäusedichtung HNBR / / / / / /33 Housing seal H7007 H7008 H6874 H68759 H70075 H70074 Gehäusedichtung FPM / / / / / /73 Housing seal H77438 H77463 H77487 H775 H77542 H77582 DN80 DN00 Menge quantity 2 Gehäuse RGMS4 Ausführung 3A-blank Housing design 3A-bright finish Gehäuse RGMS4 Ausführ. matt-glänzend Housing design satin finish Flansch FGX Ausführung 3A-blank Flange FGX design 3A-bright finish Flansch FGX Ausführ. matt-glänzend Flange FGX design satin finish Dichtung FGN seal FGN H5803 H5804 H5805 H / / / / / /93 H77325 H77339

27 Weitergabe sowie Vervielfältigung dieser Unterlage, Verwertung und Mitteilung ihres Inhalts nicht gestattet, soweit nicht schriftlich zugestanden. Verstoß verpflichtet zum Schadensersatz und kann strafrechtliche Folgen haben (Paragraph 8 UWG, Paragraph 06 UrhG). Eigentum und alle Rechte, auch für Patenterteilung und Gebrauchsmustereintragung, vorbehalten. SPX FLOW, Germany Ersatzteilliste: spare parts list Regelventil RGMS4- DN25-00 Antrieb MAT3277 (MFS o.mfh) 20,240,350 cm² el-pneum. oder pneum. Stellungsregler; lineare oder gleichproz. Kennlinie Modulating valve RGMS4- DN25-00 with diaphragm actuator MAT3277 (spring: closed or open) 20,240,350 cm² el.-pneum. or pneum. positioner; flow characteristics: linear and equal percentage Datum: Name: Trytko Trytko Trytko Trytko Knöchel Datum: Name: Trytko Trytko SPX FLOW Germany Blatt 3 von 9 RN pos. Skt. Schraube 9 DIN EN 2407-A Hex. screw Führungsbuchse 0 20x9 Bushing Flachkopf Schraube Flat headed screw Kontermutter Mating nut Hubanzeige Stroke indicator Beschreibung item description material DIN EN ISO 207-A270 5 mm DN25 DN40 DN50 DN65 WS-Nr. WS-Nr. WS-Nr. WS-Nr. WS-Nr. ref.-no. ref.-no. ref.-no. ref.-no. ref.-no /5 4xM8x6 H A /3 H A /7 H /64 76x3,75 H /23 H /2 H /93 H /64 22x3,5 H A /23 H /64 H /3 H676 DN80 DN00 WS-Nr. ref.-no. Menge quantity O-Ring 20,2x3 O-ring Laterne Yoke Laterne Ausführ. matt-glänzend Yoke design satin finish Schaft oben Upper valve shaft O-Ring O-ring Membrane Diaphragm Ausführung 3A-blank design 3A-bright finish Material Ketronpeek 000 EPDM EPDM TFM Stern Star /5 8xM0x6 H A /3 H A /7 H /42 H /64 95x4,5 H /23 H /2 H32036 Membranunterstützung /93 7 Ryton R4-XT Fan support H38535 O-Ring EPDM /64 8 O-ring 24x3,5 H W-Verschraubung G/8" /4" OD /93 9 PA-.430 Elbow union Schwenkbar / slewable H32732 Befestigungsblech für Hubanz / mounting plate for stroke indicat. H6763 M0x /42 H /3 M5x2 H /5 H62483

28 Weitergabe sowie Vervielfältigung dieser Unterlage, Verwertung und Mitteilung ihres Inhalts nicht gestattet, soweit nicht schriftlich zugestanden. Verstoß verpflichtet zum Schadensersatz und kann strafrechtliche Folgen haben (Paragraph 8 UWG, Paragraph 06 UrhG). Eigentum und alle Rechte, auch für Patenterteilung und Gebrauchsmustereintragung, vorbehalten. SPX FLOW, Germany Ersatzteilliste: spare parts list Datum: Name: Trytko Trytko Trytko Trytko Regelventil RGMS4- DN25-00 Antrieb MAT3277 (MFS o.mfh) 20,240,350 cm² el-pneum. oder pneum. Stellungsregler; lineare oder gleichproz. Kennlinie Modulating valve RGMS4- DN25-00 with diaphragm actuator MAT3277 (spring: closed or open) 20,240,350 cm² el.-pneum. or pneum. positioner; flow characteristics: linear and equal percentage Knöchel SPX FLOW Germany Datum: Blatt 4 von 9 Name: Trytko RN pos. Beschreibung Material DN25 DN40 description material DN50 DN /94 H75308 DN80 DN00 WS-Nr. WS-Nr. WS-Nr. WS-Nr. WS-Nr. WS-Nr. ref.-no. ref.-no. ref.-no. ref.-no. ref.-no. ref.-no. Menge quantity item Entlüftungsstopfen 24 2 G/8" PHT/BLACK Venting plug Pos. 3, 8, 0,, 4, 5, 8, 26 nur im kompletten Dichtungssatz erhältlich Item 3, 8, 0,, 4, 5, 8, 26 available as complete seal kits only Dichtungssatz 3A /00 3A /00 3A /00 3A /00 3A /00 3A /00 FPM Seal kit H A /0 3A /0 3A /0 3A /0 EPDM Dichtungssatz Seal kit Dichtungssatz VMQ Seal kit Dichtungssatz Seal kit HNBR 3A /0 3A /0 H H H H H33799 H A /02 3A /02 3A /02 3A /02 3A /06 3A /06 3A /06 3A /06 H3302 3A /02 3A /02 3A /06 3A /06

29 Weitergabe sowie Vervielfältigung dieser Unterlage, Verwertung und Mitteilung ihres Inhalts nicht gestattet, soweit nicht schriftlich zugestanden. Verstoß verpflichtet zum Schadensersatz und kann strafrechtliche Folgen haben (Paragraph 8 UWG, Paragraph 06 UrhG). Eigentum und alle Rechte, auch für Patenterteilung und Gebrauchsmustereintragung, vorbehalten. SPX FLOW, Germany. Ersatzteilliste: spare parts list Regelventil RGMS4- DN25-00 Antrieb MAT3277 (MFS o.mfh) 20,240,350 cm² el-pneum. oder pneum. Stellungsregler; lineare oder gleichproz. Kennlinie Modulating valve RGMS4- DN25-00 with diaphragm actuator MAT3277 (spring: closed or open) 20,240,350 cm² el.-pneum. or pneum. positioner; flow characteristics: linear and equal percentage Datum: Name: Trytko Knöchel Datum: Name: Trytko Trytko Trytko Trytko Blatt 5 SPX FLOW Germany von 9 RN pos. item description Tellerdichtung Seat seal Tellerdichtung Seat seal Material material.4404 FPM DN25/2,5 DN25/4,0 DN25/6,3 WS-Nr. WS-Nr. WS-Nr. ref.-no. ref.-no. ref.-no. Menge quantity * Beschreibung Schaft-lineare Kennlinie LD * Shaft flow characteristics -linear LD * Schaft-gleichprozentige Kennlinie G * Shaft flow character. -equal percentage G * Schaft-gleichprozentige Kennlinie GD * Shaft flow character. -equal percentage GD *.4404 Tellerdichtung HNBR Seat seal Tellerdichtung VMQ Seat seal / / / /42 H H35322 H3068 H / /42 H3200 H /33 H /3 H77443 DN25/0 WS-Nr. ref.-no / /42 H3069 H Ventilsitz metallisch dichtend / Valve seat metal sealing H52848 Ventilsitz / / Valve seat H2676 H Ventilsitz mit Lochkäfig (geräuscharm) / / Valve seat with punched cage (low noise) H4694 H Reduzier Nippel /93 G/4"-/8" MS58 Reducing nipple H für Antr.-Fläche Kupplungskopf klein /5 for actuator area.430 Hose coupling small H cm2 Kupplungskopf groß /5.430 Hose coupling great H * Schaft-lineare Kennlinie L * Shaft flow characteristics -linear L * für Antr.-Fläche for actuator area 240, 350cm2 MAT 3277 siehe / see RN und / and RN EPDM / /42 H33458 H L-lineare Kennlinie-metall dichtend / L-charakteristics linear -metal sealing LD-lineare Kennlinie-weich dichtend / LD-characteristics linear -soft sealing G-gleichprozentige Kennlinie-metall dichtend / G-characteristics equal percentage-metal sealing GD-gleichprozentige Kennlinie-weich dichtend / GD-characteristics equal percentage-soft sealing /93 H /73 H77444 WS-Nr. WS-Nr. ref.-no. ref.-no.

30 Weitergabe sowie Vervielfältigung dieser Unterlage, Verwertung und Mitteilung ihres Inhalts nicht gestattet, soweit nicht schriftlich zugestanden. Verstoß verpflichtet zum Schadensersatz und kann strafrechtliche Folgen haben (Paragraph 8 UWG, Paragraph 06 UrhG). Eigentum und alle Rechte, auch für Patenterteilung und Gebrauchsmustereintragung, vorbehalten. SPX FLOW, Germany Ersatzteilliste: spare parts list Datum: Name: Trytko Trytko Trytko Trytko Regelventil RGMS4- DN25-00 Antrieb MAT3277 (MFS o.mfh) 20,240,350 cm² el-pneum. oder pneum. Stellungsregler; lineare oder gleichproz. Kennlinie Modulating valve RGMS4- DN25-00 with diaphragm actuator MAT3277 (spring: closed or open) 20,240,350 cm² el.-pneum. or pneum. positioner; flow characteristics: linear and equal percentage Knöchel SPX FLOW Germany Datum: Name: Trytko Blatt 6 von 9 RN pos. Menge quantity 26 Ventilsitz metallisch dichtend.4404 Valve seat metal sealing 27 Ventilsitz / / / Valve seat H26762 H33479 H33480 Ventilsitz mit Lochkäfig (geräuscharm) / / / Valve seat with punched cage (low noise) H44862 H4520 H48260 Reduzier Nippel /93 28 G/4"-/8" MS58 Reducing nipple H708 für Antr.-Fläche Kupplungskopf klein /5 for actuator area.430 Hose coupling small 29 20cm2 H62484 Kupplungskopf groß /5.430 Hose coupling great H /42 Schaft-lineare Kennlinie L *.4404 Shaft flow characteristics -linear L * H Schaft-lineare Kennlinie LD * / / / / / / Shaft flow characteristics -linear LD * H H35322 H3068 H H H Schaft-gleichprozentige Kennlinie G *.4404 Shaft flow character. -equal percentage G * Schaft-gleichprozentige Kennlinie GD *.4404 Shaft flow character. -equal percentage GD * * * Beschreibung Material DN40/2,5 DN40/4,0 DN40/6,3 DN40/0 DN40/6 DN40/25 item description material 25 Tellerdichtung EPDM Seat seal Tellerdichtung FPM Seat seal Tellerdichtung HNBR Seat seal Tellerdichtung VMQ Seat seal für Antr.-Fläche for actuator area 240, 350cm2 MAT 3277 siehe / see RN und / and RN L-lineare Kennlinie-metall dichtend / L-charakteristics linear -metal sealing LD-lineare Kennlinie-weich dichtend / LD-characteristics linear -soft sealing G-gleichprozentige Kennlinie-metall dichtend / G-characteristics equal percentage-metal sealing GD-gleichprozentige Kennlinie-weich dichtend / GD-characteristics equal percentage-soft sealing WS-Nr. WS-Nr. WS-Nr. WS-Nr. WS-Nr. WS-Nr. ref.-no. ref.-no. ref.-no. ref.-no. ref.-no. ref.-no /42 H / / / / / /42 H32000 H35323 H3069 H H H / /93 H77445 H / /73 H77444 H /33 H /3 H /33 H /3 H77468

31 Weitergabe sowie Vervielfältigung dieser Unterlage, Verwertung und Mitteilung ihres Inhalts nicht gestattet, soweit nicht schriftlich zugestanden. Verstoß verpflichtet zum Schadensersatz und kann strafrechtliche Folgen haben (Paragraph 8 UWG, Paragraph 06 UrhG). Eigentum und alle Rechte, auch für Patenterteilung und Gebrauchsmustereintragung, vorbehalten. SPX FLOW, Germany Ersatzteilliste: spare parts list Regelventil RGMS4- DN25-00 Antrieb MAT3277 (MFS o.mfh) 20,240,350 cm² el-pneum. oder pneum. Stellungsregler; lineare oder gleichproz. Kennlinie Modulating valve RGMS4- DN25-00 with diaphragm actuator MAT3277 (spring: closed or open) 20,240,350 cm² el.-pneum. or pneum. positioner; flow characteristics: linear and equal percentage Datum: Name: Trytko Trytko Trytko Knöchel Datum: Name: Trytko Trytko SPX FLOW Germany Blatt 7 von 9 RN pos Beschreibung Material.4404 Tellerdichtung EPDM / /93 Seat seal H77445 H77470 Tellerdichtung FPM /73 Seat seal H77444 Tellerdichtung HNBR /33 Seat seal H7273 DN50/6,3 DN50/0 DN50/6 DN50/25 DN50/40 WS-Nr. WS-Nr. WS-Nr. WS-Nr. WS-Nr. WS-Nr. ref.-no. ref.-no. ref.-no. ref.-no. ref.-no. ref.-no. Menge quantity item Schaft-lineare Kennlinie L * Shaft flow characteristics -linear L * Schaft-lineare Kennlinie LD * Shaft flow characteristics -linear LD * Schaft-gleichprozentige Kennlinie G * Shaft flow character. -equal percentage G * Schaft-gleichprozentige Kennlinie GD * Shaft flow character. -equal percentage GD * material / / / / / /42 H3068 H H H H H /73 H /33 H7275 Tellerdichtung VMQ / /3 Seat seal H77443 H77468 Ventilsitz metallisch dichtend Valve seat metal sealing.4404 Ventilsitz Valve seat / / / /42 H3069 H H H Ventilsitz mit Lochkäfig (geräuscharm) Valve seat with punched cage (low noise) Reduzier Nippel /93 28 G/4"-/8" MS58 Reducing nipple H708 für Antr.-Fläche Kupplungskopf klein /5 for actuator area.430 Hose coupling small 29 20cm2 H62484 Kupplungskopf groß /5.430 Hose coupling great H * * description für Antr.-Fläche for actuator area 240, 350cm2 MAT 3277 siehe / see RN und / and RN L-lineare Kennlinie-metall dichtend / L-charakteristics linear -metal sealing LD-lineare Kennlinie-weich dichtend / LD-characteristics linear -soft sealing G-gleichprozentige Kennlinie-metall dichtend / G-characteristics equal percentage-metal sealing GD-gleichprozentige Kennlinie-weich dichtend / GD-characteristics equal percentage-soft sealing / /42 H H / /93 H77494 H /73 H /33 H /3 H / / /42 H3348 H33482 H / / /47 H494 H452 H44859 DN65/ /73 H /33 H /3 H /42 H /47 H4524

32 Weitergabe sowie Vervielfältigung dieser Unterlage, Verwertung und Mitteilung ihres Inhalts nicht gestattet, soweit nicht schriftlich zugestanden. Verstoß verpflichtet zum Schadensersatz und kann strafrechtliche Folgen haben (Paragraph 8 UWG, Paragraph 06 UrhG). Eigentum und alle Rechte, auch für Patenterteilung und Gebrauchsmustereintragung, vorbehalten. SPX FLOW, Germany Ersatzteilliste: spare parts list Datum: Regelventil RGMS4- DN25-00 Antrieb MAT3277 (MFS o.mfh) 20,240,350 cm² el-pneum. oder pneum. Stellungsregler; lineare oder gleichproz. Kennlinie Modulating valve RGMS4- DN25-00 with diaphragm actuator MAT3277 (spring: closed or open) 20,240,350 cm² el.-pneum. or pneum. positioner; flow characteristics: linear and equal percentage Name: Trytko Trytko Trytko Trytko Knöchel SPX FLOW Germany Datum: Blatt 8 von 9 Name: Trytko RN pos. Beschreibung Material DN65/25 DN65/40 DN65/63 DN80/25 item description material DN80/40 DN80/63 WS-Nr. WS-Nr. WS-Nr. WS-Nr. WS-Nr. WS-Nr. ref.-no. ref.-no. ref.-no. ref.-no. ref.-no. ref.-no. Menge quantity Schaft-lineare Kennlinie L *.4404 Shaft flow characteristics -linear L * Schaft-lineare Kennlinie LD * / / / / / / Shaft flow characteristics -linear LD * H H H3070 H H H3070 Schaft-gleichprozentige Kennlinie G *.4404 Shaft flow character. -equal percentage G * Schaft-gleichprozentige Kennlinie GD * / / / / / / Shaft flow character. -equal percentage GD * H H H20790 H H H20790 Tellerdichtung EPDM / / / / / /93 Seat seal H77470 H77494 H7758 H77470 H77494 H7758 Tellerdichtung FPM / / / / / /73 Seat seal H77469 H77493 H7757 H77469 H77493 H7757 Tellerdichtung HNBR / / / / / /33 Seat seal H7275 H65709 H7278 H7275 H65709 H7278 Tellerdichtung VMQ / / / / / /3 Seat seal H77468 H77492 H7756 H77468 H77492 H7756 Ventilsitz metallisch dichtend.4404 Valve seat metal sealing 27 Ventilsitz / / / / / / Valve seat H33484 H33485 H33486 H05569 H33487 H33488 Ventilsitz mit Lochkäfig (geräuscharm) / / / / / / Valve seat with punched cage (low noise) H4524 H4522 H48263 H6760 H4525 H4523 Reduzier Nippel /93 28 G/4"-/8" MS58 Reducing nipple H708 für Antr.-Fläche Kupplungskopf klein /5 for actuator area.430 Hose coupling small 29 20cm2 H62484 Kupplungskopf groß /5.430 Hose coupling great H * * für Antr.-Fläche for actuator area 240, 350cm2 MAT 3277 siehe / see RN und / and RN L-lineare Kennlinie-metall dichtend / L-charakteristics linear -metal sealing LD-lineare Kennlinie-weich dichtend / LD-characteristics linear -soft sealing G-gleichprozentige Kennlinie-metall dichtend / G-characteristics equal percentage-metal sealing GD-gleichprozentige Kennlinie-weich dichtend / GD-characteristics equal percentage-soft sealing

33 Weitergabe sowie Vervielfältigung dieser Unterlage, Verwertung und Mitteilung ihres Inhalts nicht gestattet, soweit nicht schriftlich zugestanden. Verstoß verpflichtet zum Schadensersatz und kann strafrechtliche Folgen haben (Paragraph 8 UWG, Paragraph 06 UrhG). Eigentum und alle Rechte, auch für Patenterteilung und Gebrauchsmustereintragung, vorbehalten. SPX FLOW Germany Ersatzteilliste: spare parts list Datum: Regelventil RGMS4- DN25-00 Antrieb MAT3277 (MFS o.mfh) 20,240,350 cm² el-pneum. oder pneum. Stellungsregler; lineare oder gleichproz. Kennlinie Modulating valve RGMS4- DN25-00 with diaphragm actuator MAT3277 (spring: closed or open) 20,240,350 cm² el.-pneum. or pneum. positioner; flow characteristics: linear and equal percentage Name: Trytko Trytko Trytko Trytko Knöchel SPX FLOW Germany Datum: Blatt 9 von 9 Name: Trytko RN pos. Beschreibung Material DN80/00 DN00/63 DN00/00 DN00/60 item description material DN DN WS-Nr. WS-Nr. WS-Nr. WS-Nr. WS-Nr. WS-Nr. ref.-no. ref.-no. ref.-no. ref.-no. ref.-no. ref.-no. Menge quantity Schaft-lineare Kennlinie L * Shaft flow characteristics -linear L *.4404 Schaft-lineare Kennlinie LD * / / / Shaft flow characteristics -linear LD * H36324 H3070 H36324 Schaft-gleichprozentige Kennlinie G *.4404 Shaft flow character. -equal percentage G * Schaft-gleichprozentige Kennlinie GD * / / / / Shaft flow character. -equal percentage GD * H36323 H20790 H36323 H35908 Tellerdichtung EPDM / / / /93 Seat seal H77549 H7758 H77549 H77589 Tellerdichtung FPM / / / /73 Seat seal H77548 H7757 H77548 H77588 HNBR / / / /33 Tellerdichtung Seat seal H7280 H7278 H7280 H7283 Tellerdichtung VMQ /3/ / /3/ /3 Seat seal H77547 H7756 H77547 H77587 Ventilsitz metallisch dichtend.4404 Valve seat metal sealing 27 Ventilsitz.4404 Valve seat Ventilsitz mit Lochkäfig (geräuscharm) Valve seat with punched cage (low noise) Reduzier Nippel 28 G/4"-/8" MS58 Reducing nipple für Antr.-Fläche Kupplungskopf klein for actuator area.430 Hose coupling small 29 20cm2 Kupplungskopf groß.430 Hose coupling great 30 * * für Antr.-Fläche for actuator area 240, 350cm / / / /42 H33489 H33490 H25799 H /47 H48265 MAT 3277 siehe / see RN und / and RN L-lineare Kennlinie-metall dichtend / L-charakteristics linear -metal sealing LD-lineare Kennlinie-weich dichtend / LD-characteristics linear -soft sealing G-gleichprozentige Kennlinie-metall dichtend / G-characteristics equal percentage-metal sealing GD-gleichprozentige Kennlinie-weich dichtend / GD-characteristics equal percentage-soft sealing / / /47 H49005 H4526 H /93 H /5 H /5 H62485

34

35 Weitergabe sowie Vervielfältigung dieser Unterlage, Verwertung und Mitteilung ihres Inhalts nicht gestattet, soweit nicht schriftlich zugestanden. Verstoß verpflichtet zum Schadensersatz und kann strafrechtliche Folgen haben (Paragraph 8 UWG, Paragraph 06 UrhG). Eigentum und alle Rechte, auch für Patenterteilung und Gebrauchsmustereintragung, vorbehalten. SPX FLOW, Germany Datum: Name: Trytko Trytko Ersatzteilliste: spare parts list Regelventil RGMS4-,5-4 Zoll Antrieb MAT3277 (MFS o. MFH) 20,240,350 cm² el-pneum. Stellungsregler; lineare oder gleichproz. Kennlinie Modulating valve RGMS4-,5-4 Inch with diaphragm actuator MAT3277 (spring: closed or open) 20,240,350 cm² el-pneum. or pneum. positioner; flow characteristics: linear and equal percentage Blatt SPX FLOW Germany von 8 RN

36 Weitergabe sowie Vervielfältigung dieser Unterlage, Verwertung und Mitteilung ihres Inhalts nicht gestattet, soweit nicht schriftlich zugestanden. Verstoß verpflichtet zum Schadensersatz und kann strafrechtliche Folgen haben (Paragraph 8 UWG, Paragraph 06 UrhG). Eigentum und alle Rechte, auch für Patenterteilung und Gebrauchsmustereintragung, vorbehalten. SPX FLOW, Germany Ersatzteilliste: spare parts list Regelventil RGMS4-,5-4 Zoll Antrieb MAT3277 (MFS o.mfh) 20,240,350 cm² el-pneum. oder pneum. Stellungsregler; lineare oder gleichproz. Kennlinie Modulating valve RGMS4-,5-4 Inch with diaphragm actuator MAT3277 (spring: closed or open) 20,240,350 cm² el.-pneum. or pneum. positioner; flow characteristics: linear and equal percentage Datum: Name: Trytko Datum: Name: Trytko SPX FLOW Germany Blatt 2 von 8 RN pos. item Beschreibung description Material material ",5" 2" 2,5" WS-Nr. WS-Nr. WS-Nr. WS-Nr. WS-Nr. WS-Nr. ref.-no. ref.-no. ref.-no. ref.-no. ref.-no. ref.-no. 3A /43 3A /43 3A /43 3A /43 3A /43 H H H A /47 3A /47 3A /47 3A /47 3A / H3229 H H H Flansch FGX Ausführ. matt-glänzend / / / / / Flange FGX design satin finish H58846 H58847 H58848 H58849 H58850 Dichtung FGN EPDM / / / / /93 seal FGN H77296 H77307 H7738 H77332 H77343 Dichtung FGN FPM / / / / /73 seal FGN H77295 H77306 H7737 H7733 H77342 Dichtung FGN HNBR / / / / /33 seal FGN H724 H7242 H7243 H7244 H7245 Dichtung FGN VMQ / / / / /3 seal FGN H77294 H77305 H7736 H77330 H7734 Dichtung FGN EPDM / / / / /93 seal FGN H77292 H77303 H7734 H77332 H77339 Dichtung FGN FPM / / / / /73 seal FGN H7729 H77302 H7733 H7733 H77338 Dichtung FGN HNBR / / / / /33 seal FGN H723 H7232 H7233 H7244 H7235 Dichtung FGN VMQ / / / / /3 seal FGN H77290 H7730 H7233 H77330 H77337 Skt. Schraube / / /5 DIN EN 2407-A Hex. Screw 4xM8x8 H xM8x20 H xM0x20 H78809 Flansch FNX Ausführung 3A-blank 3A /43 3A /43 3A /43 3A /43 3A / Flange FNX design 3A-bright finish H3228 H32383 H H Flansch FNX Ausführ. matt-glänzend / / / / / Flange FNX design satin finish H47046 H47047 H47048 H58889 H47049 Skt. Schraube / /5 DIN EN 2407-A Hex. screw 4xM8x28 H xM8x28 H " 4" Menge quantity Gehäuse RGMS4 Ausführung 3A-blank Housing design 3A-bright finish Gehäuse RGMS4 Ausführ. matt-glänzend Housing design satin finish Flansch FGX Ausführung 3A-blank Flange FGX design 3A-bright finish H32069 H H33428 H A /43 3A /43 3A /43 3A /43 3A /43