Installation Instructions W, 4W End View (WET) ± cutting tolerance (Example: 2W x 22.5 = 45W) 6

Transcription

1 1 of 12 Overview Surface Mount LEDs (Included) or 6.5 Modular LED Strip (#) Replaceable Modules (2.5W) or 3.9 (5.5W) increments up to max run ± cutting tolerance Mounting Clip (#-MC) (Not Included) 6.5 increments up to max run ± cutting tolerance 8 Maximum extrusion and lens length (Dry Location field cuttable) increments up up to to max max run run ± cutting tolerance (Run lengths required).20.3 End View (DRY) W, 4W End View (WET) W W or (2.5W) or 3.9 (5.5W) increments up to max run 2 ± increments cutting up to tolerance max run *See max run cutting for more tolerance information Specify 8 Maximum Length extrusion (19.7 ssembly and lens Increments) length (dd 2.5 (Dry to run Location for end field cap cuttable) and strain relief) 2 increments increments up up to to max max run run *See ± max run cutting for more tolerance information (Run lengths required) 2W, 4W 6W IMPORTNT VERIFY CORRECT LUMINIRE WS RECEIVED WITH CORRECT COLOR TEMPERTURE ND VOLTGE BEFORE CUTTING OR INSTLLING. CLI WILL NOT BE RESPONSIBLE IF INCORRECT LUMINIRE IS INSTLLED. PRODUCT 3.95 INFORMTION 3.95 increments up to max run ELECTRICL ± cutting tolerance For accent, 2 cove, edge, under cabinet lighting *See 2 max increments run for more up to information max run LipLEDs products require a 24 volt DC remote transformer ± cutting tolerance 24 volts DC for easy and safe installation.35 To calculate transformers.39 size find watts per foot Long life, energy efficient LEDs (Example: 2W per foot) Maximum run based on 5 mps: Specify Length (19.7 ssembly Increments) Determine length in feet (Example: 22.5 ) 20 (6W), 2 30 (4W), 36 (2W) (dd to increments run for end up cap to and max strain run relief) Calculate Load: Multiply Watts per Foot x Length in Feet ± cutting tolerance For class II applications: (Example: 2W x 22.5 = 45W) 14 (6W), 24 (4W), 36 (2W) increments up to max run Choose transformer from catalog (Example: TR50) Can be ordered to specific lengths for easier installation when exact.35 Determine maximum distance using Maximum Wire Length Table dimensions are known (Example: 10x10 8 Maximum ) extrusion and lens length.44 (Example: watts is between 40W and 80W. Using #14 wire, Plug and light system maximum distance is 37 from transformer to first LED) increments up to max run Lead wires are typically 33 long and exit ± on one cutting end tolerance INSTLLTION TOOLS REQUIRED INSTLLTION REMENDTIONS 8 Maximum extrusion and lens length Electric compound miter saw Phillips bits - sufficient quantity LipLEDs LED tape must be mechanically attached 14.4 to 28 volt cordless drill Electrical three ways directly to mounting surface using mounting clips or channels Drill bits - concrete or wood Measuring tape 2 2 increments up to max run Conduit raceway should be sleeved at one ± end for cutting low voltage tolerancewires Electrical cords Chalk line going to transformer Lens and extrusion shipped in Safety glasses Sharp scissors 8 sections (field cuttable) Marker Soldering iron with kit Electric hammer drill (optional) 8 Maximum extrusion and lens length 5.5W CLIFORNI CCENT LIGHTING, INC E. Lincoln ve. #431, naheim, C Maximum ph. extrusion CLI and lens (2254) length or \ fx CLI. ll rights reserved. CLI reserves the right to make changes or withdraw specifications without prior notice.

2 FETURES PPLICTIONS ccent, Decorative Lighting VOLTGE 24VDC LMP TYPE Modular LEDs DIMMING Forward Phase (TR) 0-10V (TR-E) Hi-Lume 1% Series (2 Wire) Hi-Lume 1% (3 Wire) LENGTH Built to Order CONSTRUCTION LED Modules (Field Cuttable - Dry Location Only) MOUNTING Mounting Clips or Mounting Channel CRI >90 EFFICCY 108 Lumens per Watt VIEWING NGLE 120 Degrees L70 LED LIFE 60,000 hrs. MXIMUM RUN* 20 (6W), 30 (4W), 36 (2W) LISTING Dry or Wet (IP65 or IP67) Location UL2108, CS C22.2#9 UL8750, CS250 *Maximum run is based on 5 mps: 20 (6W), 30 (4W), 36 (2W) For class II applications: 14 (6W), 24 (4W), 36 (2W) WRNING When using lipleds for any application, basic safety precautions should always be followed to reduce the risk of fire, electric shock, and personal injury. lipleds must be installed in accordance with the NEC or CEC as applicable. CLI will not be responsible for any damage or malfunction caused by the following: Remove all packaging from lighting and accessories before installing Do not exceed maximum length per circuit. Each maximum run requires additional power feed from the transformer Do not cover lipleds as the covering may cause it to overheat, melt, or ignite. Do not install lipleds in hazardous locations or closer than 6 inches from any curtain or similar combustible material. Do not use lipleds if damaged, such as broken outer jacket, loose connections, or frayed wire insulation. Inspect periodically. Do not submerge lipleds in liquid. Do not mount lipleds with staples, nails, or like means that might damage the insulation. Mount with double-sided tape and mounting clips. Do not install lipleds in places where it is subject to continuous flexing. Do not mount lipleds inside tanks or enclosures of any kind without sufficient ventilation. Ground Fault Circuit Interrupter (GFCI) protections are required on circuits or outlets. Surge protector must be set up for electrical power system to avoid damaging lipleds lighting system. Do not install in an environment where excessive heat may exist. mbient temperature -40 F F (-20 C - 50 C). Only wet location models are intended for outdoors. See package label for environmental details. Do not install wet location model in areas where water will collect. Do not modify wet location extrusion, end caps, or power connectors. 2 of 12 Overview DIMMING PROTOCOL (Forward Phase Dimming) Technical Requirements for Control Equipment (Forward Phase Dimming) Magnetic Low Voltage (MLV) - Magnetic (core and coil, toroidal) transformer-supplied low voltage lighting. Electrical Characteristics - Inductive Special Requirements - Symmetric cycles Symmetric Forward Phase-Control (VDC 2), smooth turn off (positive and negative periods are equal for safe MLV transformer operation) Order transformer with TR prefix. (TR) Forward Phase Dimming DIMMING PROTOCOL (0-10V) LipLEDs are available in 120 or 277 volts with a dimmable remote driver. The remote driver is available with 0-10V dimming capabilities. The following applies to 0-10V dimming interfaces. 0-10v fluorescent dimmer will not dim the LEDs. Technical Requirements for Control Equipment (0-10V Protocol) The output current level of the dimmable driver is controlled by DC voltage (0-10V) applied to the control terminals (blue and white). The light output of LEDs is controlled by the amount of output current from the dimmable driver. The control device must be capable of sinking a DC current flow from the driver. The maximum amount under any condition is 500 microamps (u) per driver. The control terminals of the dimmable driver are isolated from the power lines and are suitable for use as Class 2 wiring. Multiple drivers are desired for use with same control device, the control terminals may be connected in parallel in a bus configuration. Since the control bus is Class 2 wiring, all control devices that are connected to the power line must have proper isolation between the power line and the control terminals/bus. The control device, which intends to control more than one dimmable driver, must be capable of sinking the total current supplied to control bus by the drivers. If the control terminals/bus is shorted in any case, the current on the control terminals/bus will be 500 microamps (u) per driver maximum. If the control terminals are opened, the voltage on the control terminals will then be 10V ± 0.5 volt. s a result, dimmable driver supplies maximum output current to LEDs under this condition. The driver is intended for use with control voltages between 0 and 10VDC. The control equipment must not impose a voltage greater than 11 V peak maximum on the driver control terminals. Order transformer with TR-E prefix. (TR-E) 0-10V Dimming CLIFORNI CCENT LIGHTING, INC E. Lincoln ve. #431, naheim, C ph CLI (2254) or \ fx CLI. ll rights reserved. CLI reserves the right to make changes or withdraw specifications without prior notice.

3 Do not connect lightstrip to power source while spooled or coiled 3 of 12 Product Care Do not penetrate lightstrip with any foreign object TR Do not overlap lightstrips at any location Do not apply excessive pressure to surface of lightstrip or LEDs Do not overlap extrusions in any way Do not install lightstrip in a zig-zag fashion Do not cover lightstrip with any material Do not install connectors without shrink tube for wet location TR Do not install wet location in outdoor cove without proper drainage Do not use a lighter or flame to heat shrink tube CLIFORNI CCENT LIGHTING, INC E. Lincoln ve. #431, naheim, C ph CLI (2254) or \ fx CLI. ll rights reserved. CLI reserves the right to make changes or withdraw specifications without prior notice.

4 4 of 12 pplication Guidelines REQUIRES TEM EFFORT TO ENSURE SECURE ND CORRECT INSTLLTION pply pressure to module, ensuring adherence to surface Remove adhesive backing Feed from wire puller stand One person on one end removes adhesive backing from double-sided tape, then applies modules to surface nother person unreels from spool, holding lightstrip at 45 angle IMPORTNT NOTE TO VOID COLOR SHIFT: Do not paint on or over fixture lens or LEDs. Paint or any other substance on lens or LEDs will cause a shift in color temperature. Soffit must be painted evenly with a neutral white to avoid color shift. CLIFORNI CCENT LIGHTING, INC E. Lincoln ve. #431, naheim, C ph CLI (2254) or \ fx CLI. ll rights reserved. CLI reserves the right to make changes or withdraw specifications without prior notice.

5 1. Measure area where will be installed. REMENDTION: Use chalk line to ensure a straight installation. 5 of 12 Mounting Clips (Dry Location) 4. Screw mounting clips to surface. Remove adhesive backing from double-sided tape, then apply to mounting clips. 20 Chalk line Remove adhesive backing 2. Mark location where mounting clips will be installed. REMENDTION: Use one mounting clip in the middle of each fixture 3. Lay mounting clips and pre-drill using proper screw size and drill bit for surface. REMENDTION: 8/32 X 1 screw CLIFORNI CCENT LIGHTING, INC E. Lincoln ve. #431, naheim, C ph CLI (2254) or \ fx CLI. ll rights reserved. CLI reserves the right to make changes or withdraw specifications without prior notice.

6 1. Measure area where will be installed. REMENDTION: Use chalk line to ensure a straight installation. 6 of 12 Mounting Clips (Wet Location) 4. Screw mounting clip to surface, then snap fixture into mounting clips. pply silicone at both ends of each run to seal fixture. 20 Chalk line 2. Mark location where mounting clips will be installed. REMENDTION: Quantity of mounting clips = quantity of fixture +1. Use a mounting clip at the joint between two fixtures Lay mounting clips and pre-drill using proper screw size and drill bit for surface. REMENDTION: 8/32 X 1 screw pply silicone CLIFORNI CCENT LIGHTING, INC E. Lincoln ve. #431, naheim, C ph CLI (2254) or \ fx CLI. ll rights reserved. CLI reserves the right to make changes or withdraw specifications without prior notice.

7 PUSH PUSH 7 of 12 Mounting Fixture (Dry Location) 1. Measure area where will be installed. REMENDTION: Use chalk line to ensure a straight installation. 5. Conduct continuity test. Troubleshoot Good Chalk line 2. Drill holes as needed with drill bit and countersink. 20 If a conductive path is formed between positive and negative wire, the multimeter will beep. You need to trouble shoot to find the short. PUSH PUSH If there is no conductive path, the multimeter VDC will not beep. Countersink hole 3. Screw channel into desired surface using countersink holes. NOTE: Surface must be flat. Ensure screw is flush with channel PUSH PUSH See page 10 for troubleshooting guide 6. Set voltmeter to DC voltage, then test power source before connecting. Power source DC TR Power Source DC VDC DC DC Confirm the correct voltage, depending on the light strip. 7. Connect power source to power lead. If LEDs do not turn on, flip polarity (+,-) or power source connection to power connector. VDC 4. Remove adhesive backing from double-sided tape, then apply to channel. Power connector Remove adhesive backing pply to channel Ensure is secured to channel Channel CLIFORNI CCENT LIGHTING, INC E. Lincoln ve. #431, naheim, C ph CLI (2254) or \ fx CLI. ll rights reserved. CLI reserves the right to make changes or withdraw specifications without prior notice.

8 1. Measure area where will be installed. REMENDTION: Use chalk line to ensure a straight installation. 8 of 12 Mounting Fixture (Wet Location) Sealed connectors 20 Chalk line Drill holes as needed with drill bit and countersink pply silicone to seal connections Countersink hole 6. pply silicone at both ends of each run to seal fixture. 3. Screw channel into desired surface using countersink holes. NOTE: Surface must be flat. Ensure screw is flush with channel Conduct continuity test. Troubleshoot Good pply silicone 4. Snap into mounting channel. If a conductive path is formed between positive and negative wire, the multimeter will beep. You need to trouble shoot to find the short. If there is no conductive path, the multimeter VDC will not beep. See page 10 for troubleshooting guide Ensure is secured in place 8. Set voltmeter to DC voltage, then test power source before connecting. Power source DC DC DC Confirm the correct voltage, depending on the light strip. Channel DC 5. If applicable,slide shrink tube over connectors 1-B1 and apply heat. Shrink tube will shrink down completely to seal the connectors. Shrink tube pply heat 6. Connect power source to power lead. If LEDs do not turn on, flip polarity (+,-) or power source connection to power connector. TR Power Source Power connector.5.5 CLIFORNI CCENT LIGHTING, INC E. Lincoln ve. #431, naheim, C ph CLI (2254) or \ fx CLI. ll rights reserved. CLI reserves the right to make changes or withdraw specifications without prior notice

9 1. Remove module and double-sided tape. Remove module and double-sided tape 9 of 12 Replacing Modules 4. pply new double-sided tape to modules, then apply to surface. Only apply tape underneath modules in between bottom connectors. Do not reuse old tape. REMENDED TPE: 3M 4004 Double-Sided Foam Tape - 1/4 x 1/4 pply new tape pply to channel 2. Size to desired length by removing modules as needed. Insert a pin into each hole on the bottom connectors to release wires. Release wires Insert pin here to release wires Double-sided tape in-between bottom connectors Release wires Insert pin here to release wires 5. Ensure is applied securely to surface. 3. Connect modules by inserting wires back into bottom connectors. NOTE: 2W and 4W boards have + and - indicator markings on the bottom. 6W board has no markings, use the below diagram to determine + and - wires. Insert wires into bottom connector Ensure is secured in place Insert wires into bottom connector 2W and 4W 6W CLIFORNI CCENT LIGHTING, INC E. Lincoln ve. #431, naheim, C ph CLI (2254) or \ fx CLI. ll rights reserved. CLI reserves the right to make changes or withdraw specifications without prior notice.

10 TROUBLESHOOT Do not reset breaker multiple times. If the unit is overloaded the breaker will trip shutting off the transformer and lights. If the breaker reset button has been held down by hand or any type of pressure (example: duct tape), or if the breaker has been reset multiple times without trouble shooting, the unit will: - Burn the transformer bobbin - Burn the thermal or magnetic breaker - Burn the primary or secondary wires due to high amperage caused by overload and/ or short circuit in line which will not allow the breaker to reset - Damage the lighting 10 of 12 Troubleshooting 5. Ensure loose wires are not making contact with aluminum extrusion. Loose wires touching extrusion 6. Check for water inside end cap and power connector. If water is present, remove water before connecting to power. 7. Do not connect boost tap from transformer voltage. Ensure that voltage does not exceed 24VDC. 1. Turn off power before beginning. Check for any damage to the circuit in the LED board. If there is excessive damage and circuit is broken, the board must be replaced. Damaged board 8. Conduct continuity test. If a conductive path is formed between positive and negative wire, the multimeter will beep. You need to trouble shoot to find the short. VDC Troubleshoot VDC Good If there is no conductive path, the multimeter VDC will not beep. VDC 2. Check for metal particles or other foreign objects causing the short. 9. Set voltmeter to DC voltage, then test power source before connecting. DC DC Power source DC Confirm the correct voltage, depending on the light strip. Foreign object Metal flakes DC 3. Check for broken or improperly cut boards. 10. Connect power source to power lead. If LEDs do not turn on, flip polarity (+,-) or power source connection to power connector. Improper cut TR Power Source 4. Ensure the board are properly aligned and not overlapping Power connector Overlapping boards CLIFORNI CCENT LIGHTING, INC E. Lincoln ve. #431, naheim, C ph CLI (2254) or \ fx CLI. ll rights reserved. CLI reserves the right to make changes or withdraw specifications without prior notice.

11 11 of 12 Transformer WTTS (V) PER CIRCUIT (Maximum wire length to prevent voltage drop) WIRE SIZE VOLTGE 40 V 80 V 120 V 160 V 200 V 240 V 260 V 280 V 300 V 320 V 14G 12V G 24V G 12V G 24V G 12V G 24V G 12V G 24V TRNSFORMER CRE Do not submerge transformer in any liquid Do not leave any exposed wires Do not cover transformer without proper ventilation Do not install damaged transformer MGNETIC LOW-VOLTGE DIMMER RTINGS The stated V (volt-ampere) rating is the rated capacity of the dimmer which includes the magnetic transformer heat losses and the lamp load. transformer dissipates less than 20% of the connected load as heat. dded together,the lamp load and the transformer loss determine the dimmer capacity required. See the example below. 600V Power to transformer and power through dimmer 120W Heat Transformer Losses (UL limit: 80% efficient) 480W Lamp load CLIFORNI CCENT LIGHTING, INC E. Lincoln ve. #431, naheim, C ph CLI (2254) or \ fx CLI. ll rights reserved. CLI reserves the right to make changes or withdraw specifications without prior notice.

12 12 of 12 Maintenance CLENING MTERILS FOR LENSES ND EXTRUSIONS The use of solvents and/or cleaners which are not compatible with polycarbonate will result in the softening, crazing, and/or cracking of the plastic part. This is especially true of polycarbonate lamps and mounting bases which may be under stress in their normal applications. PTIBLE WITH POLYCRBONTE: Mild soap and water Mineral Spirits Isobutyl alcohol VM and P Naphtha Varsol No.2 Mexane Freone TF and TE-35 Ethanol Dirtex 2% Sol. Reg. Joy 10% Sol Bon mi White Kerosene Methyl alcohol Heptane Petroleum Ether/65 degrees C Isopropyl alcohol Lacryl PCL-2035 polycarbonate cleaner NOT PTIBLE WITH POLYCRBONTE Trichlor Gasoline ll Liquid Detergents cetone Carbon Tetrachloride Pink Lux (Phosphate free) Triclene Chlorinated Hydrocarbons #1 & #3 denatured alcohol Methyl Ethyl Keytone (MEK) Texize-8006, 8129, 8758 MIBK Liquid Cleaner 8211 Toluol gitene Benzol jax Kleenol Plastics Lysol Stanisol Naphtha Oils Lemon Joy (phosphate free) Diversol Lestoil CLIFORNI CCENT LIGHTING, INC E. Lincoln ve. #431, naheim, C ph CLI (2254) or \ fx CLI. ll rights reserved. CLI reserves the right to make changes or withdraw specifications without prior notice.