LineLED Flex 18 Horizontal plan bendable LED strip - 24 VDC

Transcription

1 LineLED Flex 18 Horizontal plan bendable LED strip - 24 VD LineLED Flex 18 is a small profile, high output LED strip specially designed for installations with horizontal plan bend. ending sections every 1.30 on center allow the LineLED Flex 18 to fit around tight curves. Mounting LineLED Flex18 strip is equipped with 3M self-adhesive tape. The strip must be adhered to either a Luminii aluminum profile or an unpainted aluminum surface. For other surfaces the HST luminum heat sink tape will be required to reach the rated 50,000 hours average life. pplications: Indoor only - cove lighting, architectural reveals, under banister, general ambient lighting, etc. pprovals lass 2 damp listed Operating voltage 24 VD verage life 50,000 hours Warranty 5 years Technical information LLFLEX18 PRODUT DIMENSIONS LEDS/ft 18 Light output 3000K 225 lum/ft verage power consumption (for 15 section) 2.65 W/ft Ordering increment 4.00 ends up to 90 ends every 1.30 on center 0.39 Maximum run length (in series) 22 ft Dimensions 0.39 W 0.05 H SETION STRT/END OPTIONS T INFO/LUMEN MULTIPLIER TM No onnection Soldered Leads olor temperature Multiplier (referenced from 3000K) RI R f R g 2200K K K K K Ordering code OLOR TEMPERTURE SETION STRT SETION END LENGTH LLFLEX18 LLFLEX18 22K 22K K 24K K 27K K 30K K 41K K SL SL - Soldered lead wires (72 ) N - No connector SL SL - Soldered lead wires (72 ) N - No connector 4 4 increments - up to 22 REV2.5 page 1 of 6 tel:

2 LineLED Flex 18 Horizontal plan bendable LED strip - 24 VD TM-30-15: Data 22K T 24K T 27K T 30K T 41K T REV2.5 page 2 of 6 tel:

3 LineLED Flex 18 Horizontal plan bendable LED strip - 24 VD Power consumption per linear foot loads tested with PSD series of power supplies (page 4) ONSUMPTION PER FOOT Length of strip (LF) W/ft Total wattage ccessories Mounting clip: recommended at every 12 when LineLED strip is facing down Heat sink tape: included with LineLED strip when no extrusions are ordered. Splice ox: low voltage, 4 terminal splice box, black. Part # L Part # HST 2.00 Part # LVSP-4T-K REV2.5 page 3 of 6 tel:

4 LineLED Flex 18 Horizontal plan bendable LED strip - 24 VD Power supply See fixture and power supply instructions & spec sheet for wiring information. Dimming possible in select models - view Luminii website for list of compatible dimmers. Non-Dimming: DIMMING LOTION PSV PSV - PSV Series W W W 24V VD U2ND U2ND - Non Dimming D D - Dry Location IP65 - Wet Location S PSV Dry PSV Wet Width Depth 2.3 Dimming 0-10V: DIMMING PS010V PS010V V Power Supply dims down to 0% 3X100 3X100-3 X 100 WTT 24 LIN VD LIN - Linear LOG - Logarithmic - features eldoled s LINERdrive configurable 0-10V drivers S Width Depth PSD010V DIMMING LOTION PSV PSV - PSV Series dims down to 5% W W W 24V VD U2DIM U2DIM - Dimming 0-10V D D - Dry Location IP65 - Wet Location S Width PSV Dry PSV Wet Depth 2.3 Dimming Magnetic low voltage: PSD PSD - PSD Series dims down to 0% W W W (3x 96W) VD INPUT lank V V V S PSD 48 PSD 96 PSD Width Depth REV2.5 page 4 of 6 tel:

5 LineLED Flex 18 Horizontal plan bendable LED strip - 24 VD Power supply See fixture and power supply instructions & spec sheet for wiring information. Dimming possible in select models - view Luminii website for list of compatible dimmers. Dimming Electronic low voltage: VE VE - VE Series dims down to 0.1% IRUIT x 48D 48D - 48W 48X2D - 2 x 48W 48X3D - 3 x 48W 48X4D - 4 x 48W 96D - 96W 96X2D - 2 x 96W 96X3D - 3 x 96W 96X4D - 4 x 96W 24V VD INPUT lank V V cover S Single circuit Dual circuit Three circuit Four circuit Width Depth 1.3 DMX & DLI: PSDMX PSDMX - DMX Power Supply PSDLI - DLI Power Supply dims down to 0% 3X100 3X100-3 X 100 WTT VD - Features eldoled s LINERdrive configurable dimmable drivers S PSDMX PSDLI Width Depth Luminii is a Lutron OEM dvantage Partner LTE4U1UKL-V240 Lutron Hi-lume 1% 2-wire LED driver (120V forward phase only) L3D4U1UKL-V240 Hi-lume 1% EcoSystem Voltage LED Driver L3D0-96W24V-U Hi-lume 0.1% EcoSystem Voltage LED Driver with Soft-On, Fade-to-lack S LTE L3D S L3DO Width Width 5.50 Depth Depth 2.00 REV2.5 page 5 of 6 tel:

6 LineLED Flex 18 Horizontal plan bendable LED strip - 24 VD Optional mounting channels - Single row LEDs RO hannel lu-roun d 45 hannel L hannel lu-45 lu-orner Slim Line 7 L F SL7 hannel N L RSL7 hannel Recessed Slim Line 7 HF F L HF F SL15 hannel Slim Line L HF F RSL15 hannel Recessed Slim Line 15 N M L HF F FL hannel lu-fl at N M L HF F lu-wall N WL hannel M L HF F N M L HF F L F SLW8 hannel Slim Wide 8 RSLW8 hannel Recessed Slim Wide 8 SLW15 hannel Slim Wide lu-et L LE hannel HF F L HF F L HF F L F 0.81 Lens options L F HF N M lear Frosted Half (50%) frosted Narrow beam frosted Medium beam frosted Installation ll mounting channels are field cuttable using miter saw with circular blade suitable for cutting aluminum. Ordering Extrusions are sold separately. View respective specsheets for details on ordering extrusions and their accessories (endcaps, mounting brackets, etc). REV2.5 page 6 of 6 tel: