Installation instructions

Transcription

1 Installation instructions Door control TS 971 Automatic control panel with radio Version: en- Version: f / XXXXX

2 GfA ELEKTROMATEN GmbH & Co. KG Wiesenstraße Düsseldorf 2

3 Contents 1 General safety information Technical data Mechanical installation Electrical installation... 9 Connection cable connection overview Limit switch configuration, screwable version up to year of construction in Limit switch configuration, single limit switches Carrying out the electrical installation Mains supply Mains supply to control Completing the electrical installation Overview of control Starting up the control DES: Rapid adjustment of final limit positions NES: Rapid adjustment of final limit positions Advanced electrical installation External supply X Emergency stop X Automatic closing, On/Off X External Control device X Photo cell X Light curtain X Radio receiver X Pull switch X Intermediate open X Red/green traffic lights X20 / X Magnetic brake X20 / X Connection of spiral cable WSD door-module (Wireless Safety Device) Electrical safety edge 8K2 to WSD door-module Optical safety edge OSE System 1 to WSD door-module Optical safety edge OSE System 2 to WSD door-module Door safety switch on "WSD" door module

4 Teach-in of WSD door-module Completing the advanced electrical installation Control programming Table menu items Door operating modes Door positions Door functions, Safety functions DI/FI settings Extended door functions Maintenance cycle counter Readout of Data memory Deleting / readout Reading out WSD door-module data Safety devices X2: Input, door safety switch function X2: Input, safety edge system Installation of the spiral cable Integrated WSD door-module EMERGENCY operation X3: Input, emergency stop Functional description X: 24 VDC voltage supply X1: Mains supply of the control and supply of external devices X4: Input, automatic closing Off/On X5: Input, control device X6: Input Through / reflective photo cell resp. light curtain X7: Input pull switch/radio receiver Internal radio receiver Teach-in of radio transmitter Deleting an individual radio transmitter Deleting all radio transmitters X8: Input, intermediate stop On/Off

5 X20 / X21: Potential-free relay contacts Force monitoring (DES only) Travel time monitoring (NES only) UBS system UBS connection Reversing duration adjustment Maintenance cycle counter Short-circuit/overload display Display for active WSD door-module wireles safety device Standby function Illumination of the built in push button of the door control Status display Faults Commands Status indications Explanation of symbols Declaration of Incorporation/Declaration of Conformity Symbols Warning - Risk of injury or danger to life! Warning - Danger to life from electrical current! Note - Important information! Prompt - Required action! Illustrations show example products. Differences from the delivered product are possible. 5

6 1 General safety information Specified use The door control is intended for a power-operated door with a drive unit (NES/DES GfA limit switch system). The safe operation is only guaranteed with specified normal use. The drive unit is to be protected from rain, moisture and aggressive ambient conditions. No liability for damage caused by other applications or non-observance of the information in the manual. Modifications are only permitted with the agreement of the manufacturer. Otherwise the Manufacturer s Declaration shall be rendered null and void. Safety information Installation and commissioning are to be performed by skilled personnel only. Only trained electrical craftsmen are permitted to work on electrical equipment. They must assess the tasks assigned to them, recognise potential danger zones and be able to take appropriate safety measures. Installation work is only to be carried out with the supply off. Observe the applicable regulations and standards. Coverings and protective devices Only operate with corresponding coverings and protective devices. Ensure that gaskets are fitted correctly and that cable glands are correctly tightened. Spare parts Only use original spare parts. 6

7 2 Technical data Series TS 971 Dimensions W x H x D 155 x 386 x 90 mm Installation Vertical, free of vibration Operating frequency 50 / 60 Hz Supply voltage (+/- 10%) 1 N~ V, PE 3 N~ V, PE 3~ V, PE Output power for drive unit, maximum 3 kw Protection per phase, on-site A External mains supply: (internal electronic protection) External mains supply: X1/L, X1/N (protection via F1 micro-fuse) Control inputs Relay contacts 24 V DC 0.35 A 1 N~230 V 1.6 A time-lag 24 V DC Type 10 2 potential-free changeover contacts ma Loading of relay contacts, ohmic/inductive 230 V AC, 1 A 24 V DC, 0,4 A Control power consumption 18 W Temperature range Air humidity Protection class of housing Operation: Storage: up to 93 % non-condensing IP54 C Compatible GfA - limit switch NES (mechanical limit switch) DES (digital limit switch) Integrated radio receiver WSD (Wireless Safety Device) Handheld transmitter GHz MHz 7

8 3 Mechanical installation Control installation! Indoor use only Mounting only on even ground that is free of vibration Only vertical mounting position allowed Door must be in clear view from place of installation Requirements The permissible loads on walls, mountings, connection and transmission elements must not be exceeded. Mounting The control is mounted via 4 elongated holes 8

9 4 Electrical installation Warning - Danger to life due to electrical current! Disconnect the cables (mains OFF) and check that the supply is off Observe the applicable regulations and standards Ensure proper electrical connection Use suitable tools On-site backup fuse and mains disconnector! Only use all current sensitive earth leakage circuit breakers type B for FI-drive units Connection to the indoor installation via an all-pole disconnector unit, with current 10 A as per EN (e.g. CEE plug connector, main switch) Observe the installation instructions of the drive unit! 9

10 Connection cable connection overview A DES B X12 DES C MOT D X13 Pin Core Pin Description: Pin Core Term. Description: 1 5/wh V safety circuit 1 3 W Phase W 2 6/bn 2 Channel B (RS485) 2 2 V Phase V 3 7/gn 3 Ground 3 1 U Phase U 4 8/ye 4 Channel A (RS485) 4 4 N Neutral conductor (N) 5 9/gy 5 Safety circuit 5 PE PE 6 10/pk 6 8 V DC supply voltage A NES E X12 NES Pin Core Term. Description: 1 5/wh 11 Limit switch common +24 V, wire link to: 7, 9, 5, /bn 12 S5 Auxiliary limit switch 3 7/gn 6 S3 Open limit switch 4 8/ye 15 S6 Auxiliary limit switch 5 9/gy 8 S4 CLOSE limit switch 6 10/pk 4 Safety circuit 10

11 Limit switch configuration, screwable version up to year of construction in 1997 W (N) 3 2 S6 S5 S3 S1 S2 S4 X12 S10 F1 Thermal contact X12 Limit switch board G1 Rectifier S1 Emergency OPEN limit switch M1 Motor S2 Emergency CLOSE limit switch S10 Emergency manual operation S3 OPEN limit switch W1 Connection cable S4 CLOSE limit switch Y1 Spring-loaded brake S5 Auxiliary limit switch S6 Auxiliary limit switch F1 M1 G1 Y1 Limit switch configuration, single limit switches W PE A1 M1 S3 S4 S10 F1 S5 S6 A1 Terminal box S3 OPEN limit switch F1 Thermal contact S4 CLOSE limit switch M1 Motor S5 Auxiliary limit switch S10 Emergency manual operation S6 Auxiliary limit switch W1 Connection cable 11

12 Carrying out the electrical installation Remove covers. Open cable entry 1 or 2. Insert and connect connection cable in the open cable entry 1 (from below) or 2 (from above). Properly tighten cable glands. Avoid damage to parts! Open cable entry with suitable tool 12

13 Mains supply 3~, N, PE 3~, PE 1~, N, PE, sym. 1~, N, PE, asym V V V V Hz Hz Hz Hz L1 L2 L3 N PE L1 L2 L3 PE N PE N PE SI WS, SI 45.7 WS SI WS, SI 45.7 WS Mains supply to control 3 Completing the electrical installation Install and tighten cable entries and/or cable glands. For commissioning of the control, leave the covers open. 13

14 Overview of control DES/ NES S11 MOT S12 S13 V1 UBS S X3 X4 X5 X X6 X7 X8 X2 971 T X21 X F1 GN D ANT F1 = 1,6A t DES/ NES F1 MOT DES or NES limit switch socket Micro-fuse 1.6 A time-lag Motor socket X X1 X2 X1 24 V mains supply, external devices Mains supply Safety edge and door safety switch S Selector switch X3 Emergency STOP control device S11 OPEN push-button X4 Automatic closing On/Off S12 STOP push-button X5 Control device, external three push-button S13 CLOSE push-button X6 Through / reflective photo cell T Internal aerial, 434 MHz X7 Pull switch, external radio receiver UBS Universal command sensor socket X8 Intermediate open On/Off V1 Display X20 Potential-free relay contact 1 X21 Potential-free relay contact 2 14

15 5 Starting up the control Supply cables Insert / switch on DES: Rapid adjustment of final limit positions 1. Check output rotating direction 2. Move to OPEN final limit position 3. Save OPEN final limit position 4. Move to CLOSE final limit position 5. Save CLOSE final limit position Note! The rapid adjustment is complete, "Hold-to-run" door operating mode is active Change of OPEN/CLOSE final limit positions via menu items "1.1" to "1.4" Pre-limit switch Safety edge is set automatically Changing the pre-limit position is possible via menu item "1.5" 15

16 Observe the installation instructions of the drive unit! For adjusting the mechanical limit switch, see the drive unit installation instructions NES: Rapid adjustment of final limit positions 1. Check output rotating direction 2. Move to OPEN final limit position and adjust S3 OPEN limit switch 3. Move to CLOSE final limit position 5cm above the ground and adjust S5 pre-limit switch 4. Move to CLOSE final limit position and adjust S4 CLOSE limit switch 16

17 0 External supply X1 Emergency stop X3 Automatic closing, On/Off X4 External Control device X5 Photo cell X6 6 Advanced electrical installation External supply X1 Emergency stop X3 Automatic closing, On/Off X4 X1 X3 X4 A1 A2 2 S15 1 S17 A1 External device A2 Control device A3 Control device Emergency stop Key switch A External Control device X5 X5 X5 A6 S X5 A4 S17 1 P 2 S S A4 Key push-button A6 Three push button Photo cell X6 X6 X6 X V 12 24V V 12 24V V A8 A9 A10 A11 A12 PNP A8 Reflective photo cell Through-beam photo cell Through-beam photo cell A9 Transmitter A11 Transmitter A10 Receiver A12 Receiver 17

18 Light curtain X6 Radio receiver X7 Pull switch X7 Intermediate open X8 Red/green traffic lights X20 / X21 Magnetic brake X20 / X21 Light curtain X6 X X20 24V 24V* V 24V* 24V 24V* V X V 24V 24V* V X V PNP A25 A26 A27 A28 X20 Function relay Light curtain Light curtain X21 Function relay A25 Transmitter A27 Transmitter Test light curtain A26 Receiver A28 Receiver Radio receiver X7 Pull switch X7 Intermediate open X8 X7 X7 X V 4 4 S19 S17 12 A13 A14 3 A15 3 Red/green traffic lights X20 / X21 Magnetic brake X20 / X21 X20/ X20/ Y G1 C1 H2 H1 H1 Traffic light, green G1 Rectifier H2 Traffic light, red Y1 Magnetic brake 18

19 Connection of spiral cable X X X2 3 2 ST A18/A19 Electrical safety edge A18 ST+ ST SK1 SK2 Pneumatic safety edge A18 ST+ ST SK1 SK2 Connection of spiral cable B1 Optical safety edge system A19 ST+ ST SK/b SK/g SK/w Door safety switch ST A18/A19 S30/ S31 A20 br gn Door safety switch, crash switch S38 A w ST A18/A19 DW 1K2 S39 A22 8K2 R2 B2 B3 R1 2 1 A18 ST+ ST SK1 SK2 B1 R1 X2 Junction box Mains supply Input for door safety switch Input electrical safety edge Electrical safety edge End of line resistor (8k2) Door control socket A18 Junction box ST+ Mains supply ST Input for door safety switch SK1 SK2 Input pneumatic safety edge DW Pneumatic switch R2 End of line resistor (1k2) X2 Door control socket A19 Junction box ST+ Mains supply ST Input for door safety switch SK/b Mains supply (brown) SK/g Output (green) SK/w Earth (white) B2 Optical transmitter B3 Optical receiver X2 Door control socket A18 A19 A20 S30 S31 A18 A19 A21 S38 A22 S39 Junction box Junction box switch Pass-door switch (NC contact) Slack-rope switch (NC contact) Junction box Junction box switch Crash switch (NC contact) Junction box switch Crash switch (NO contact) 19

20 WSD door-module (Wireless Safety Device) Electrical safety edge 8K2 to WSD door-module Optical safety edge OSE System 1 to WSD door-module WSD door-module (Wireless Safety Device) Direction for opening A23 WSD door module 6 ST2 Socket for system-2 connection cable 1 P1 WSD door-module push-button 7 S2 Safety edge evaluation switch: 2 S1 Switch A for system 1, switch B for system 2 Optical (upper changeover position, IR ) 3 G1 Lithium battery, 9000 mah Electrical (lower changeover position) 4 X1/2 Connection point for door safety switch 8 KL1 Terminal for: 5 ST3 Socket for optical sensor / System-2 connection cable Electrical safety edge 9 ST1 Socket for optical sensor Electrical safety edge 8K2 to WSD door-module Optical safety edge OSE System 1 to WSD door-module 20

21 Optical safety edge OSE System 2 to WSD door-module Door safety switch on "WSD" door module Optical safety edge OSE System 2 to WSD door-module A23 WSD door module A24 System 2 end box A24 Door safety switch on "WSD" door module S A24 A24 System 2 end box 2 S38 1 A21 X1 / X2 S38 A

22 Teach-in of WSD door-module Teach-in of WSD door-module Insert battery Supply cables insert / switch on Activate Channel 8, for example Available channels Teach in WSD door-module connected, dot on right is lit Note! Use of a safety edge only possible via menu item "0.1", door operating mode.3,.4 or.6 Completing the advanced electrical installation If required, connect other electrical equipment and/or safety devices. Install and tighten cable entries and/or cable glands. 22

23 7 Control programming 1. Start programming Note! Possible after rapid adjustment of final limit positions 2. Select menu item and confirm 3.a) Set and store functions 3.b) Set and store positions 4. Exit programming 23

24 Door operating modes 8 Table menu items Door operating modes Door operating mode OPEN CLOSE OPEN CLOSE OPEN CLOSE OPEN CLOSE Hold-to-run Hold-to-run Self-hold Hold-to-run Self-hold Self-hold Self-hold Self-hold, CLOSE hold-to-run release via external X5 control device OPEN CLOSE Hold-to-run Hold-to-run with active safety edge Output rotating direction Maintain output rotating direction Change output rotating direction 24

25 Door positions Door positions OPEN final limit position, coarse correction (DES) Approach and store desired door position CLOSE final limit position, coarse correction (DES) Approach and store desired door position OPEN final limit position, fine correction (DES) Without door movement, [ + ] OPEN correction [ ] CLOSE correction CLOSE final limit position, fine correction (DES) Without door movement, [ + ] OPEN correction [ ] CLOSE correction Fine-correction pre-limit switch for safety edge (DES) Adjust intermediate open X8 (DES)* Without door movement, [ + ] OPEN correction [ ] CLOSE correction Approach and store desired door position Setting for position of relay 1 switching point (DES)* Select relay function via menu item 2.7 Approach and store desired door position Setting for position of relay 2 switching point (DES)* Select relay function via menu item 2.8 Approach and store desired door position *) Menu items 1.6 to 1.7 disappear at NES. The switching point must be adjusted via the S6 auxiliary limit switch at the drive unit. 25

26 Door functions, Door functions, part 1 Safety device Spiral cable Teach-in of WSD door-module wireless safety device.2 to 4.0: Manual channel selection Up to 39 doors: Do not assign any radio channel twice. If more than 39 doors: Ensure maximum distance between the door controls with the same channels. Note taught-in channels in the controls housing. Important for service work. Pay attention to the WSD door-module manual Safety edge function in the pre-limit area Safety edge active Safety edge inactive Ground adjustment (DES) (Activation of safety edge at ground contact) Reversing in overrun area (DES) Overrun correction (DES) Off On (Do not use with ground adjustment) 26

27 Door functions, Part 2 Automatic closing 0 to 240 seconds Extended photo cell function Off Cancel automatic closing and CLOSE command Vessel recognition Cancellation of automatic closing and CLOSE-command if photo cell activation duration > 1.5 seconds Reversing 0 = Off 1 to 10 safety-device activations Pull switch or radio receiver function X7 Type of impuls 1 Door is in OPEN final limit position CLOSE command Door is not at OPEN final limit position OPEN command Type of impuls 2 Command sequence OPEN STOP CLOSE STOP OPEN Type of impuls 3 OPEN command only 27

28 Relay function on X20 Door functions, Part 3 Relay function on X21 X20 X21 Off Impuls contact* for 1 second Permanent contact* Red lamp, permanently lit during door movement OPEN final limit position Flashing for 3 seconds CLOSE final limit position Flashing for 3 seconds Red lamp, permanently lit during door movement OPEN final limit position Flashing for 3 seconds CLOSE final limit position Off Red lamp, permanently lit during door movement OPEN final limit position Permanently lit for 3 seconds CLOSE final limit position Permanently lit for 3 seconds Red lamp, permanently lit during door movement OPEN final limit position Permanently lit for 3 seconds CLOSE final limit position Off Dock leveller release or permanent green light Active only in OPEN final limit position Permanent contact in CLOSE final limit position Light sensing device 1-second pulse at each OPEN command Permanent contact at door position* Brake control Active during operation Inactive at stop Light curtain test, etc. Test prior to each closing operation *) Previous teach-in of door positions via menu item 1.7 (1.8) relay X20 (X21) (only DES) or respectively via the S6 auxiliary limit switch of the drive unit (NES). 28

29 Intermediate open function Door functions, Part 4 All command inputs Input X7.2 and internal radio receiver Input X5.3 and OPEN push-button of control 29

30 Safety functions Safety functions Force monitoring (DES) 0 = Off Adjustable for 2 % to 10 % overload Interruption of the photo cell function (DES) Off On (single reference position taught-in twice) Travel time monitoring (NES) 0 = Off 0 to 90 seconds Door safety switch function (Input X2.2 / WSD door-module) Slack-rope or pass-door switch Crash switch as NC contact After activation: "Hold-to-run" door operating mode Crash switch as NO contact After activation: "Hold-to-run" door operating mode Crash switch as NC contact After activation: Reversing in OPEN final limit position. Reset after contact reset otherwise "Hold-to-run" door operating mode Crash switch as NO contact After activation: Reversing in OPEN final limit position. Reset after contact reset otherwise "Hold-to-run" door operating mode Automatic opening (Automatic closing menu item 2.3) 0 = Off 0 to 99 minutes Reversing duration adjustment [ + ] slower [ ] faster 30

31 DI/FI settings DI/FI settings OPEN output speed Output speed in rpm CLOSE output speed Output speed in rpm Increased CLOSE output speed Up to an opening height of 2.5 m Output speed in rpm 0 = Off Changeover position to CLOSE output speed (with adherence to minimum opening height requirement of 2.5 m!) Approach and store desired door position OPEN acceleration DI FI Steps of 1.0 seconds Steps of 0.1 seconds CLOSE acceleration DI FI Steps of 1.0 seconds Steps of 0.1 seconds OPEN deceleration DI FI Steps of 1.0 seconds Steps of 0.1 seconds CLOSE deceleration DI FI Steps of 1.0 seconds Steps of 0.1 seconds OPEN/CLOSE crawling speed Output speed in rpm 31

32 Extended door functions Extended door functions Selection of radio transmitters manufacturer (434 MHz) Internal radio receiver deactivated (Fixcode) GfA, Tedsen Teleco "COD1" - (Rolling code of various providers) GfA UK, JCM, Dickert (Fixed code) RDA (Fixcode) TRL Radio receiver function Teach-in of a handheld transmitter Cancellation of a taught-in handheld transmitter Cancellation of all taught-in handheld transmitter 32

33 Maintenance cycle counter Maintenance cycle counter Maintenance cycle preselection corresponds to 1,000 to 99,000 cycles Cycles are counted down Reaction upon reaching "Zero" Status indication "CS" appears in turns with value set by menu item 8.5. Changeover to "Hold-to-run" door operating mode. Status indication "CS" appears in turns with value set by menu item 8.5. Changeover to "Hold-to-run" door operating mode. Status indication "CS" appears in turns with value set by menu item 8.5. Option: Press STOP-button for 3 seconds to deactivate changeover and status indications for 500 cycles. Status indication "CS" appears in turns with value set by menu item 8.5 and relay contact X21 switches. 33

34 Readout of Data memory Deleting / readout Cycle counter 7-digit number Readout of Data memory M HT ZT T H Z E Displayed in division of ten consecutively M HT = = 1,000, ,000 ZT T = = 10,000 1,000 H Z = = E = 1 Last faults Display change of the last 6 faults Data counter 7-digit number M HT ZT T H Z E Displayed in division of ten consecutively M HT = = 1,000, ,000 ZT T = = 10,000 1,000 H Z = = E = 1 Cycle counter of the last change in programming Number of activations of slack-rope, pass-door and crash switch Software version The software version of the control is displayed. For direct inverter or frequency inverter drive units, the software version of the motor is displayed as well. Deleting / readout Deleting of all settings Activating GfA stick All settings are set to factory setting! Except for cycle counter 34

35 Reading out WSD door-module data Reading out WSD door-module data WSD door-module data (Only activated at taught-in WSD door-module, Displaying of missing data is done by -.-. ) Data indicated alternately 1. Version of master radio module 2. Type of safety edge 0.0. = none 0.1. = 1k = 8k = optic 3. Door safety switch 0.0. = inactive 0.1. = active 4. Battery voltage 5. Assigned / selected communication channel 6. Signal quality ranging from 0% - 99% 35

36 9 Safety devices X2: Input, door safety switch function The door safety switch is installed on the door and connected to the door control via the spiral cable. Menu item "3.4 : Function Reaction upon activation.1 Slack-rope/Pass-door Switching contact is interrupted: Door stop Switching contact is closed: Door is ready for operation.2 Crash switch as NC contact Door stops Changeover to "Hold-to-run" door operating mode Frequency inverter: "Hold-to-run" door operating mode at crawling speed only Fault reset only possible in OPEN final limit position: Press the STOP-button of the door control for 3 seconds.3 Crash switch as NO contact.4 Crash switch as NC contact with reversing.5 Crash switch as NO contact with reversing Like function.2 Door stops + reversing Fault reset only possible in OPEN final limit position: Takes place automatically as soon as the switching contact has closed Switching contact continues to be interrupted: Changeover to "Hold-to-run" door operating mode Frequency inverter: "Hold-to-run" door operating mode only at set-up speed Like function.4 36

37 Slack-rope/Pass-door If the pass-door switch is open circuit when an open or close command is given, fault F1.2 is displayed. If activated during the door movement, the door is immediately stopped and fault F1.2 is displayed. Entrysense (electronic pass-door switch) The pass-door switch, which has been tested to performance level c (plc) in accordance with EN , is monitored by the door control. If the pass-door switch is open circuit when an open or close command is given, fault F1.2 is displayed. If activated during the door movement, the door is immediately stopped and fault F1.2 is displayed. The magnetic contacts in the pass-door switch are switched by a permanent magnet. The door control assesses the switching status of the contacts independently of each other. The F1.7 fault indication appears if there is a failure. Crash switch as NC or NO contact The crash switch is activated if the door is pushed out of the mechanical guideance. If the switching contact is activated, the door is stopped, fault indication "F4.5" is displayed, and a changeover to "Hold-to-run" door operating mode is carried out. Movement of the door is only possible via the built in push button of the door control. "Hold to run" door operating mode for frequenzy inverter only at crawling speed. The fault indication "F4.5" can only be reset in OPEN final limit position by pressing the STOP-button of the door control for more than 3 seconds or by switching the mains voltage off and on. Fault indication "F4.5" will recur, if the switching contact continues to be activated. With the reversing function, a reset is carried out automatically in the OPEN final limit position as soon as the switching contact is closed. Otherwise only "Hold-to-run" door operating mode is possible. 37

38 X2: Input, safety edge system The door control automatically detects three different safety edges to protect the closing movement of the gate wing. Important! Connect safety edge systems in accordance with EN "Hold-to-run" door operating mode can always be used should the safety edge be defective Electrical safety edge The input is meant for an electrical safety edge (NO) with a terminal resistance of K2 (+/-5% and 0,25W). If there is a short circuit, fault indication "F2.4" is displayed. If there is an open circuit, the "F2.5" fault indication appears. Pneumatic safety edge The input is meant for a pressure wave switch system (NC) with a terminal resistance of 1K2 (+/-5% and 0,25W). Upon activation or permanent disconnection of the current circuit, the "F2.6" fault indication appears. If there is a short circuit, fault indication "F2.7" is displayed. The pressure wave switch system needs to be tested with CLOSE final limit position. The test phase is initiated automatically by the pre-limit for DES. If no switching signal is generated on the pressure wave switch within 2 seconds, the test is negative and the fault indication F2.8 is displayed. 38

39 Optical safety edge system The input is meant for an infrared safety beam sensor with transmitter and receiver in a rubber profile. By pressing the rubber profile, the light beam is interrupted. The F2.9 fault indication appears upon activation or a faulty safety edge system Installation of the spiral cable The spiral cable should enter the door control panel from the left- or right-hand side. The spiral cable should be fixed in place with a cable gland. The safety edge system is connected via the 3-pole plug, and the slack-rope or the pass door via the 2-pole plug. Important! Check position of S5 pre-limit switch on the safety edge (only for NES) When the door is opened > 5cm, a reversing must be executed if the safety edge has been activated Function: Safety edge function in the pre-limit area Menu item "2.1": Function Reaction to activation of safety edge.1 Active Door stops.2 Inactive.3 Ground adjustment (DES) No reaction Door moves to CLOSE final limit position Door stops; correction of the CLOSE final limit position at the next closing.4 Reversing in overrun area (DES) Reversing upwards from the overrun area upon activation of the safety edge system 39

40 Note: Ground adjustment! Automatic compensation of rope elongations or changes in ground conditions of approx. 2-5 cm With DES limit switch only Do not use with overrun correction Do not use with pneumatic switch Note: Reversing upwards in the overrun area! To maintain the operating forces in the pre-limit area At high speeds With DES limit switch only Function for FI-drive units not necessary Function: Overrun correction function (only DES) Menu item "2.2": Automatic limit switch correction to achieve a constant CLOSE position. Function Overrun correction.0 Off.1 On Note: Overrun correction! With DES limit switch only Do not use with ground adjustment 40

41 Function: Reversing Menu item "2.5": Limiting of the number of reversing movements following safety edge system activations via automatic closing. If the set value is exceeded, automatic closing is deactivated and the "F2.2" fault indication is displayed. Note! To reset fault "F2.2": Move to CLOSE final limit position 41

42 Integrated WSD door-module The WSD door-module replaces the spiral cable and is mounted on the door leaf. The signals of the safety edge are transmitted by radio to the door control. The radio receiver is integrated as standard in door control TS 971. Commissioning via "Teach-in of the WSD door-module". Attention Damage to components! Use additional splash guard ( ) in car washes (to avoid cracked seals: For example plasticizer, surfactants) Keep imported cables as short as possible to plug connections and terminals Avoid installing the lines directly above the receiver board Avoid bending the aerial Carefully close the cover Usable safety devices Safety edge systems 8K2 resistor evaluation Optical safety edge (universal or low-power sensors only) Door safety switch Slack-rope or pass-door switch Crash switch with NC contact 42

43 Note! For a description of the safety device and relevant adjustment procedures see X2 Crash switch function as NO contact is hidden If the battery is low, fault indication "F1.9" appears and there is a changeover to the "Hold-to-run" door operating mode F1.6 fault indication: Door movement only possible via EMERGENCY operation When performing annual maintenance tasks involving the door system, replace the WSD door-module battery as a precautionary measure Menu item "9.6": Alternating display of WSD door-module statuses including version of master radio module Type of safety edge: "0.0." = none "0.1." = 1k2 "0.2." = 8k2 "0.3." = optic Door safety switch: "0.0." = inactive "0.1." = active Battery voltage Assigned / selected communication channel Signal quality ranging from 0% - 99% 43

44 EMERGENCY operation Warning! For EMERGENCY operation, the door has to be checked (it has to be in a faultfree state) Hold-to-run door operating mode: The door must be fully visible from the operating point EMERGENCY operation allows for moving the door to a required position by bypassing faults with the signal transmission of the safety device. EMERGENCY operation is activated after pressing the STOP push-button and holding for 7 seconds, and is indicated by the flashing display. Note! The door cannot be moved in case of F1.3 and F1.4 fault indications for reasons of operating safety. Activation of EMERGENCY operation: Use the built in push button of the control to press and hold the STOP-button while simultaneously pressing the OPEN or CLOSE push-button to move the door X3: Input, emergency stop Connection of an emergency stop control device as per EN or an evaluation unit for an anti-trap safety device. The F1.4 fault indication appears upon activation. Note! Frequency inverter drive unit: The emergency stop switches the supply off. The door control can only be operated again 10 seconds after unlocking the emergency stop. (Display rotates during this time) 44

45 10 Functional description X: 24 VDC voltage supply Connection of external devices such as photo cell, radio receiver, relay, etc. via the "24 V" and "GND" terminals. Attention Damage to components! Total current consumption of external devices: maximum 350 ma X1: Mains supply of the control and supply of external devices Mains supply of the control Connection via the terminals X1/1.1 to X1/1.4 and PE. Various mains supplies: 3 N~, 3~, 1 N~ for symmetric and asymmetric motors. Note! Pay attention to the "Mains supply" and "Mains supply connection to control" descriptions Supply of external devices Connection of external devices for 230 V, such as photo cell, radio receiver, relay, etc. via terminals X1/1.8 and X1/1.9. Note! Mains supply: 3 N~400 V or 1 N~230 V, symmetric Protection via F1, 1.6-A time-lag micro-fuse 45

46 X4: Input, automatic closing Off/On Connection of a switch via the terminals X4/1 and X4/2 for switching the automatic closing off and on. X5: Input, control device Warning! "Hold-to-run" door operating mode: The door must be fully visible from the operating point The door operating mode "3" allows a place of installation of the control device without sight of the door. Note! Application without STOP push-button: Connect wire link X5.1 to wire link X5.2 If the safety edge or photo cell fails, the control device will not function 46

47 X6: Input Through / reflective photo cell resp. light curtain Photo cell A photo cell is used for presence detection. It is only active in door operating modes.3 and.4, in the OPEN final limit position or during the CLOSE-operation. If the light beam is interrupted, fault indication "F2.1" appears. Light curtain The light curtain must be self-testing and correspond at least to safety category 2 or performance level c (plc). If the light curtain corresponds to these requirements, the door can close into self-hold without safety edge system. Important! Operation without safety edge: Connect resistor 8K2 via the terminals X2/3 and X2/4 Photo cells must not be used via the UBS system if a light curtain is used Do not use menu item "3.2" for the light curtain To test the light curtain, activate relay contact X20 or X21. The relay functions are described under menu item "2.7" / "2.8". If the light beam is interrupted, fault indication "F4.6" appears. With every CLOSE-command a test is run. Thereby the contact of the light curtain must switch off within 100 ms. If the test is positive, the contact must switch back on within 300 ms. If the test is negative, the fault indication "F4.7" is displayed. To reset fault indication "F4.7": Switch control off and on. Note! Only use photo cells or light curtains with "Light switching" mode 47

48 Reaction to interrupting of light beam Door position CLOSE final limit position OPEN-operation OPEN final limit position Without automatic closing OPEN final limit position With automatic closing OPEN final limit position With automatic closing and time interruption Reaction to interrupting of light beam No action No action No action Reset automatic closing The door closes 3 seconds after the interruption period for the light beam has ended Extended photo cell function Menu item "2.4 : Function Extended photo cell function.0 No action.1 Cancel automatic closing The door closes 3 seconds after the interruption period for the light beam has ended.2 Vessel recognition The door closes after the interruption period for the light beam has ended, if the interruption period is longer than 1.5 seconds Reset of automatic closing if the interruption duration for the light beam is equal to or less than 1.5 seconds 48

49 Disconnection of photo cell function (only DES) Menu item "3.2" Function Disconnection of photo cell function.0 Off.1 On The teach-in mode gets activated after exiting the programming. Warning! Presence detection is disabled in the teach-in mode In the teach-in mode, the door must be fully opened and closed twice. The light beam must be interrupted twice at the same door position. The teach-in mode is then terminated. The photo cell has no function below this stored door position. Teach-in mode display Upon exiting the programming When the light beam is interrupted for the first time After the second interruption to the light beam at the same door position, and with the CLOSE final limit position reached Note! If the teaching in is not successful, open and close the door again, so that two identical door positions are stored 49

50 X7: Input pull switch/radio receiver Connection of a pull switch or external radio receiver via the terminals X7/1 and X7/2. The switching contact must be potential-free (NO contact). Pull switch or radio receiver function Menu item "2.6": Type of impuls Reaction upon activation.1 Door is in OPEN final limit position resp. intermediate open position: The door CLOSES From all other door positions or door movements: The door OPENS.2 OPEN-STOP-CLOSE-STOP-OPEN command order.3 Door always executes OPEN movement 50

51 Teach-in of radio transmitter Internal radio receiver The integrated radio receiver can be set for a specific radio transmitter manufacturer via menu item "7.6". Handheld transmitters can be taught or deleted via menu item "7.7". Note! A combination of different radio transmitter manufacturers is possible Only use 434-MHz handheld transmitters Up to 64 radio channels can be taught Teach-in of handheld transmitters 1. Select radio transmitter manufacturer s system 2. Activate radio transmitter 3. Carry out teaching-in 4. Switch to door operation 51

52 Deleting an individual radio transmitter Deleting all radio transmitters Deleting an individual radio transmitter 1. Activate delete, 10 seconds active 2. Delete 3. Switch to door operation Deleting all radio transmitters 1. Delete all channels 2. Switch to door operation 52

53 X8: Input, intermediate stop On/Off Connect a switch to terminals X8/1 and X8/2 to activate and deactivate the intermediate open. The intermediate open position muss be programmed via menu item 1.6. With an OPEN command, the door moves to the stored door position. When the Intermediate open function is deactivated, the door can move back to the OPEN final limit position. Intermediate open function Menu item "2.9": Function Intermediate open.1 All command inputs.2 Intermediate open via X7 pull switch and internal radio receiver; OPEN final limit position via all other control devices.3 Intermediate open via external control devices X5 and OPEN push button of the control OPEN final limit position via all other control devices Note! Double command with functions.2 and.3 : Priority is given to OPEN final limit position, independent of command sequence 53

54 X20 / X21: Potential-free relay contacts The relay functions are described under menu item "2.7" / "2.8". Attention Damage to components! Maximum electrical current of 1 A at 230 VAC and 0.4 A at 24 VDC We recommend the use of LED lamps When using light bulbs, these should have power of maximum 40 W and be shock-proof Force monitoring (DES only) Menu item "3.1": The force monitoring can only be used with fully balanced doors and drive units with DES. It should be able to detect when persons are moving with the door. Warning! The force monitoring is no substitute for safety measures in providing protection against the trapping hazard Function Force monitoring.0 Off : Low limit value 1.0 : High limit value Important! Force monitoring for doors with spring balance only Environmental factors such as changes in temperature or wind load can lead to inadvertent triggering of force monitoring 54

55 After exiting programming, the door must carry out a full OPEN and CLOSE-operation in selfhold mode. The force monitoring is a self-learning system which is effective for an opening gap of 5 cm to 2 m (approx.). Slow progressive changes, e.g. gradual reduction of the spring torsion, are compensated automatically. After force monitoring has been triggered, only the "Hold-to-run" door operating mode is possible and the "F4.1" fault indication is displayed. The resetting occurs when a final limit position for the door is reached. Travel time monitoring (NES only) Menu item "3.3" The set travel time is automatically compared with the time measured for movement between the final limit positions. If the travel time is exceeded, the "F5.6" fault indication appears. Fault indication "F5.6" is reset by closing the door. Note! The travel time is set at the factory to 90 seconds Recommended setting value: door travel time + 7 seconds 55

56 UBS connection UBS system The UBS system is a simple plug-in connection technology from GfA. The control devices are connected to the control by a commercially available patch cable and detected automatically. Note! The UBS devices function in the same way as wired control devices UBS connection Three push button Reflective photo cell External Radio receiver Pull switch Reversing duration adjustment Menu item "3.8": Shortening the reversing duration serves for a reduction of the operating forces. Extending it, on the other hand, will reduce the wear on the door mechanism. 56

57 Maintenance cycle counter Menu item "8.5": A value between 0 and 99,000, as a multiple of 1000, can be adjusted for the maintenance cycle setting. The maintenance cycle counter reading is reduced by one each time the Open final limit position is reached. Once the maintenance cycle reaches zero, the setting from menu item 8.6 is activated. Short-circuit/overload display If there is a short circuit or an overload of the 24 VDC supply voltage, the 7-digit display vanishes. Display for active WSD door-module wireles safety device If the WSD door-module wireless safety device is active, an additional red point is displayed on the right-hand digit display. 57

58 Standby function If there is no fault or command pending, the control switches to "Standby". If the automatic closing duration is longer than 60 seconds. the control also switches to "Standby" Only the left dot is lit up. With active WSD door-module, both dots are lit up. The "Standby" function is terminated with a command or by activation of the selector switch "S". Illumination of the built in push button of the door control Only the command push-buttons which enable a logical next command are illuminated. 58

59 11 Status display Faults Faults Display: "F" and code Code Fault description Fault causes and fault correction Terminals X2.1 X2.2 are open. Slack-rope switch/pass-door contact is open. Open safety circuit (DES) Emergency manual operation has been activated. Thermal protection of the motor has tripped Terminals X3.1 X3.2 are open. Emergency stop has been activated. Radio transmission of WSD door-module is faulty. Check door safety switch. Check whether the connection cable is connected. Check emergency manual operation. Check for overload or stalling of the drive unit. Check emergency stop. Check whether the connection cable is connected. Radio channel assigned twice: Use menu item 9.6 to read off the radio channel. Use menu item 2.0 to manually assign the radio channels. Moisture in WSD door-module: Replace WSD door-module und use a splash guard (optional equipment). Obstacle between WSD door-module and door control: Adapt fitting configuration or use a spiral cable. Battery voltage too low: Read off voltage value using menu 9.6 and replace battery if this is less than 3.2 V. Red LED in WSD door-module: Press P1 push-button. Flashing: Faulty radio connection Lit: Radio connection OK Pay attention to the WSD door-module manual 59

60 Faults Display: "F" and code Code Fault description Fault causes and fault correction Faulty entrysense switch. Contact resistances are too high. Faulty entrysense installation. Open and close pass door. Check resistance. Check the pass door installation. Entrysense input X2.1 X2.2 is faulty. Switch control off and on. Replace control if necessary. WSD door-module batteries are too low. Change batteries of the WSD door-module. If the battery service life was considerably less than one year, check fault code 1.6 (radio channels assigned twice, obstacles). No safety edge detected. Check the wiring of the safety edge. Check function of WSD door-module. Terminals X6.1 X6.2 are open. Photo cell has been activated. Maximum number of reversing movements for door through safety edge system activation has been reached. (Only with automatic closing) Activation of safety edge 8k2. Safety edge 8k2 defective. Activation of safety edge 1k2. Safety edge 1k2 defective. 1k2 testing is negative. Check alignment of the photo cell. Check connection cable. Replace photo cell if necessary. Obstacles along the door travel path. Check whether the safety edge system is correctly functioning. Check whether the safety edge system is correctly functioning. Check whether the connection cable has shortcircuited. Check whether the safety edge system is correctly functioning. Check whether the connection cable is connected. Check whether the safety edge system is correctly functioning. Check whether the connection cable is connected. Check whether the safety edge system is correctly functioning. Check whether the connection cable has shortcircuited. Testing is activated in the lower final limit position. Check pre-limit switch (with NES "S5"). 60

61 Faults Display: "F" and code Code Fault description Fault causes and fault correction Wireles safety device of the WSD door-module or optical safety edge system has been activated or is defective. Check the WSD door-module. Check whether the safety edge system is correctly functioning. (DES) OPEN emergency stop switch reached. In the voltage-free state, move the door back via emergency manual operation. (NES) OPEN or CLOSE emergency stop switch reached. Emergency manual operation has been activated. Thermal protection of the motor has tripped Limit switch system has changed over from NES to DES without the control being reset. Check OPEN/CLOSE emergency stop switch. Check emergency manual operation. Check drive unit for overload or stalling. Reset of control via menu item "9.5". (DES) CLOSE emergency stop switch reached. In the voltage-free state, move the door back via emergency manual operation. (NES) Faulty activation of the S5 pre-limit switch. Check the S5 pre-limit switch for correct functioning and setting. No limit switch detected (active at initial operation). Connect the limit switch to the control. Check the limit-switch connection cable. Limit switch system has changed over from DES to NES without the control being reset. Reset of control via menu item "9.5". Internal plausibility error. Execute fault clearance trough movement command. Internal control temperatur too high. Switch of control and let it cool down. Triggering of force monitoring. Check the door mechanism for stiffness. Crash switch X2.1 X2.2 is activated. Check crash switch / connection cable. To reset fault: Press STOP-button and hold for 3 seconds. 61

62 Faults Display: "F" and code Code Fault description Fault causes and fault correction Terminals X6.1 X6.2 are open. Light curtain has been activated. Light curtain defective. Check light curtain. Check whether the connection cable is connected. Comply with the light curtain manufacturer s specifications. Check connection cable. Fault of the controller. Switch control off and on. Replace control if necessary. ROM error. Switch control off and on. Replace control if necessary. CPU error. Switch control off and on. Replace control if necessary. RAM error. Switch control off and on. Replace control if necessary. Internal fault of control. Switch control off and on. Replace control if necessary. Fault of digital limit switch (DES) Fault with door movement. Check DES connector and connection cable. Switch control off and on. Check the door mechanism for stiffness. Check the limit switches for correct rotational movement. Switch control off and on. Fault with rotating direction. Change rotating direction via menu item 0.2. Unacceptable door movement in stopped state. No compliance with specified travel direction at drive unit. Execute fault clearance trough movement command. Check brake and drive unit. Execute fault clearance trough movement command. Check for overload of the drive. 62

63 Faults Display: "F" and code Code Fault description Fault causes and fault correction DI / FI closing speed is too high. Switch control off and on. Replace drive unit if necessary. Internal FI communication fault. Low voltage in the DC voltage sink. Excess voltage in the DC voltage link. Temperature limit exceeded. Permanent current overload. Switch control off and on. Replace FI drive unit if necessary. Execute fault clearance trough movement command. Check mains input voltage. Change slope durations/speeds. Check mains input voltage. Execute fault clearance trough movement command. Change slope durations/speeds. Check for overload of the drive unit. Cool down the drive unit and reduce the number of cycles. Check for overload of the drive unit. Check the door mechanism for stiffness or weight. Brake / FI fault. Collective indication for FI. At initial operation minimum travel distance was not completed. Check brake; replace if necessary. If problem recurs, replace drive unit. Execute fault clearance trough movement command. Replace drive unit if message is continually displayed. Move the door for at least 1 second. 63

64 Commands Commands Display: "E" and code Code Command description An OPEN-command is present. Inputs X5.3, X7.2, internal radio system, UBS control device or UBS radio receiver A STOP command is present. Inputs X5.2, X7.2, internal radio system, UBS control device or UBS radio receiver or simultaneous OPEN and CLOSE commands A CLOSE command is present. Inputs X5.4, X7.2, internal radio system, UBS control device or UBS radio receiver Status display Status indications Description Preset value for maintenance cycle counter reached. Dot on left is not lit: control circuit has a short circuit or is overloaded. Dot on right is lit: internal WSD door-module is active. Function for changing the rotating direction is activated, only possible during initial operation. Change of rotating direction has been carried out, only possible during initial operation. 64