Model AX Custom Anodes

Transcription

1 Model AX Custom Anodes EDI can customize any of its anodes or design special anodes to meet the unique requirements of a particular application. These products are usually designated as Model AX followed by a sequence number. This data sheet shows a few of the custom models we have built. Contact us for additional information on custom design anodes. Special and Custom Impressed Current Anodes: Model AL AX02 AX15 AX18 AX21 AX23 Description Model AL is a low profile strip anode which only projects 1 inch from the vessel wall. Model AX02 is flush mounted on the wall of a large diameter water tunnel. Dimensions are sized to suit the box recess. Model AX15 is a rod anode with a cantilever or tee mount. It is used where the entire anode is immersed such as waterfront structures Model AX18 is a 4 foot strip anode which projects 2 inches from the vessel wall. Model AX21 is a fully immersible 1/8 inch dia. probe anode. Model AX23 is a suspended tubular anode. info@edi-cp.com A Series Impressed Current Anodes AX3.docx-08/15 EDI 2015

2 l + 6 l w + 2 w Active surface Polyurethane casting 5/8 Ø thru 2 as specified 1 m + 4 Dimensional Limits Low profile anodes can be made in any custom size subject to the limits shown in the table at right. l w Min. 6 in. 1 in. Max. 20 in. 10 in. (l + 6) x (w + 2) must be less than 200. Specify as EDI Model AL-asm-l.w.ttt a = active surface: M for mixed metal oxide or P for platinum s = substrate: T for titanium m = waterbox wall thickness l = active surface length, inches w = active surface width, inches ttt = micro-inches platinum: 100, 150, 200, 250 or 300; or electrolyte for mixed metal oxide: F, B or S for Fresh, Brackish or Salt water EDI info@edi-cp.com Low Profile Anode Assembly HALF 31 MAY 2011 ALASY-6

3 Mounting hole in G-10 Size and location to suit 8-32 flat head Ti machine screw 8-32 Ti nut Pin underwater connector 1/2-13 Ti nut Pt or MMO coated Ti anode bolted and bonded to recess in G-10 panel Size to suit Plate thkns.050" (nom.) 1/2-13 Ti stud 1" long welded to anode 6" lead wire splice to cable G-10 panel, size to suit 3/16" thick for boxes less than 6" x 6" 1/4" thick for larger boxes Socket underwater connector Connection to stud is potted Exposed Ti on backside of panel is coated. No gasketing is needed between G-10 panel and box. This design will work when fully immersed. Box Cover Flush Anode EDI info@edi-cp.com NONE 03/20/02 AX02ASY

4 Specify as EDI Model AX15T-PT5-l.ttt l = length in inches (see table) ttt = micro-inches platinum: 100, 150, 200, 250 or 300 lead wire, 6" #12AWG THHN with socket underwater connector 150# PVC 3" IPS raised face flange Anode rod lengths, l inches mm " (nom.) 1/2" Ø Pt coated Ti rod l see table Tee-mount Probe Anode EDI info@edi-cp.com HALF 6/05/02 AX15ASY-1

5 Specify as EDI Model AX15C-PT5-l.ttt l = length in inches (see table) ttt = micro-inches platinum: 100, 150, 200, 250 or # PVC 3" IPS raised face flange lead wire, 6" #12AWG THHN with socket underwater connector 1/2" Ø Pt coated Ti rod l see table Anode rod lengths, l inches mm /2" (nom.) Tee-mount Probe Anode EDI info@edi-cp.com HALF 6/05/02 AX15ASY-3

6 active surface 6 3/4 PVC socket fitting 40 in. x 2 in. anode element 250 micro-inches Pt on Nb cast polyurethane AWG #6 USE/RHH/RHW stranded wire, length as specified (typ) 1/2-13 FRP studs embedded in casting 3 inches protruding; 5 places Strip Anode EDI info@edi-cp.com 1/8 07/01/05 AX18ASY-1

7 #14 AWG RHW/USE 3/8 in galv. pipe shrink tube current shield 1/8 in Ø Ti rod w/ 100 uin Pt 3 1/2 in 1 1/2 in 3 in 1/8 inch probe anode EDI info@edi-cp.com FULL 30 JUL 2009 AX21ASY - 3

8 Permarad or Halar lead wire #8AWGxlengthtosuit Specify as Model AX23-MTd-lt whered=tubediameter:7for3/4in.or1for1in. l=tubelengthininches t=electrolyteformmo:saltorfreshwater length Mixed Metal Oxide coated Ti tube Tiwireloop welded to tube Tubular Anode EDI 2013 NONE 24JUL2013 AX23ASY-2