UL Ti MATE Range of underwater lights. (click on document required)
|
|
- Domenic Hicks
- 6 years ago
- Views:
Transcription
1 UL Ti MATE Range of underwater lights (click on document required) Technical UL Ti MATE 75 SA (S.S) UL Ti MATE 75 SA (ALU) UL Ti MATE 75 Fixed (S.S) UL Ti MATE 75 Fixed (ALU) Brochure Info UL Ti MATE 75 SA (S.S) UL Ti MATE 75 SA (ALU) UL Ti MATE 75 Fixed (S.S) UL Ti MATE 75 Fixed (ALU) UL Ti MATE 130 SA UL Ti MATE 130 Fixed UL Ti MATE 80 Xenon UL Ti MATE 80 20w LED Qt 80 LED UL Ti MATE 130 SA UL Ti MATE 130 Fixed UL Ti MATE 80 Xenon UL Ti MATE 80 20w LED Qt 80 LED
2 UL Ti MATE RANGE - MODEL- UL Ti MATE 130 SA underwater lights limited Manufacturers of the Original underwater lights Brand Marine Lighting Products since 1991 DESCRIPTION This is the most flexible and powerful through-hull submersible marine light for the large sports fish yachts and is suitable for GRP-fibreglass and wooden hulls. The design and development of the UL Ti MATE 130 SA gave the marine market their wish with the internal adjustment (SA) which allows the beam angle to be varied from a narrow to wide beam and to universally move the beam direction by 20 degrees from within the projector housing. The UL Ti MATE 130 SA has a larger aperture which increases the light output by 25%. We advise that the light be installed 250mm below the minimum waterline. The boat must be hauled out for installation, although maintenance of the light is carried out from inside the hull. The light is IPX8 to 10 bar. TECHNICAL SPECIFICATION Lamp Type - MSD Metal Halide 150w or 250w Lamp Life Hours - Colour Temp K Voltage/Amps watt 120(V3)/230(V2)volt /0.7.A Voltage/Amps watt 198/264vac- 1.2A Glass Lens - Borosilicate glass Material - Aluminium Bronze and 5083 ALU Light Level - 150w 12,000 Lumens - 250w 19,000 lms UL Ti MATE 130 SA 12,000 or 19,000 lumen Max hull thickness 120mm UL Ti MATE 130 SA-W1 (250 WATT) ORDER NUMBER-S00475-SA-V1W1 NOTE Installation Instruction: The hole cut-out should be 100 mm. For Lamp Maintenance allow 170mm behind the projector lid. Hull thickness range 12 to 120 mm. Electrical Information: 150w - Recommended maximum distance between ballast and projector 10m. 250w - Recommended maximum distance between ballast and projector 25m. Cable - 150w-250w High temp. silicone 3 core (Part No S00111, 0.75). For additional information please visit our web site. 130mm 130mm Hole cut-out 100mm Hole cut-out 100mm 222mm Max hull thickness 120mm 222mm UL Ti MATE 130 SA-W2 (150 WATT) ORDER NUMBER-S00475-SA-V2/V3W2 underwater lights limited TM For sales telephone numbers visit
3 ORDERING NUMBERS 250 WATT LIGHTS - 120V. S00475-SA-V3W1. 230V. S00475-SA-V2W WATT LIGHTS - 120V. S00475-SA-V3W2. 230V. S00475-SA-V2W2 UL Ti MATE 130 SA INSTALLATION (The UL Ti MATE 130 SA should be no less than 250mm/10 below the water line) Qualified/Approved personnel must be used to carry out installation Cut and prepare a 4 inch / 100 mm clearance hole for the body (16). Coat the flange of the body and the area around the hole with 3M 4200FC sealant then slide the body into the hole. From the inside fit the compensating ring (17) and screw the securing ring (18) up hand tight. Adjust the screws (19) so the compensating ring is flush to the hull and check the sealant has flowed completely around the flange. Do NOT over tighten the screws as this will squeeze the sealant from the surface. Allow the sealant to solidify and remove surplus. Finally tighten the adjustment bolts to 4Nm / 3ft.lbs Note for cored hulls - After cutting, the exposed surfaces of the hole must be finished to form a solid surface through it, thus protecting the internal core of the hull. Maximum hull thickness should not exceed 4.75 inches - 120mm Minimum wall thickness 0.375inches.- 10mm After completing the installation procedure it is highly recmmended to coat the exposed body with antifouling. EARTHING LIGHT FOR CATHODIC PROTECTION-tighten the earth screw on the securing ring so that it bites into the screwed barrel. Check there is continuity to the front face. This prevents galvanic corrosion. ELECTRONIC BALLAST COMPLETE WITH IP65 ENCLOSURE UL Ti MATE 130 SA submersible through hull light OPERATIONAL CONDITIONS AND CONSIDERATIONS The UL Ti MATE 130 is serviced from inside the hull. Allow a minimum of 170mm behind the cable gland for lamp replacements on 150w and 150mm behind the.ignitor on 250w ELECTRICAL INFORMATION CABLE SPECIFICATION TO PROJECTOR 150 Watt High temp silicone three core part number. S Watt Two core 1mm square. maximum diameter 6mm 150 WATT Max distance between ballast and projector with -10 meters.250 WATT Max distance 25 meters.ballast power 150 watt ballast 120/230 volt, running current 1.4/0.7.A Ballast power 250 watt ballast 120/230 volt, running current 2.4/1.2.A Ballast will not ignite a hot lamp. The ballast has three attempts to ignite the lamp then will wait for four minutes before repeating the cycle. Do not attempt to remove the glass lens while afloat Part Description 130-SA Part No 1: Projector lid securing plate B 2: M6 Nut : 'O' Ring : Gasket NAF A 5: Connecting ring C 6: Lamp holder screw : Lamp holder (250W) : Lamp holder (150W) : Reflector collar bush A 9: M4 Lock nut : Lamp (250W) : Lamp (150W) : Reflector adjustment rod D 12: Reflector complete S : Glass retaining ring B 13A: Cap head screws : Glass gaskets NAF A 16: Body S00475-A 17: Compensating ring : Securing ring : Cap head screws : Ignitor (250W) S : Projector cover (250W) H 22: Gland : Projector cover (150W) E 24: Ballast 250 watt S00800-V1W2 24: Ballast 150 watt 230v S00800-V2W2 24: Ballast 150 watt 120v S00800V3W2 TM 150 watt 250 watt EARTH TAB AND SCREW LENS FITTING INSTRUCTIONS Check the glass landing surface is clean and apply a suitable silicone grease to the gaskets. Fit the glass, gaskets and retaining ring as shown above. Hand tighten the screws with an Allen key making sure the glass retaining ring is square. Torque the screws to 6 Nm (4.5ft/lbs) in the sequence shown, check the ring again and re-torque the screws again to the same setting PLEASE REGISTER YOUR PRODUCT WARRANTY DIRECT TO WWW,REGISTER-UWL.COM FOR TECHNICAL INFORMATION PLEASE T@UNDERWATERLIGHTS.COM SALES, PRODUCT INFORMATION AND NEWS GO TO WWW,UNDERWATERLIGHTS.COM UL Ti MATE 130 SA Recommended Spares Part No Lamp ( 250w = W1 ) Lamp ( 150w = W2 ) Glass with gaskets S00281-A Ballast S00801
4 UL Ti MATE RANGE - MODEL - UL Ti MATE 130 -FIXED underwater lights limited Manufacturers of the Original underwater lights Brand Marine Lighting Products since 1991 DESCRIPTION This is a 150 watt MSD discharge lamp through-hull submersible marine light with a flush lens for the large sports fish boats, motor and sailing yachts and is suitable for GRP-fibreglass and wooden hulls. The UL Ti MATE 130 FIXED has a larger aperture than our original screwed fitting which has increased the light output by 25%. We advise that the light be installed 250mm below the minimum waterline. The boat must be hauled out for installation, although maintenance of the light is carried out from inside the hull. The light is IPX8 to 10 bar. TECHNICAL SPECIFICATION Lamp Type - MSD Metal Halide 150w Lamp Life Hours - Colour Temp K Voltage - 120(V3) or 230(V2) vac- Amps v = 1.4 amps 230 volt = 0.7 amps Flush Glass Lens - Borosilicate glass Material - Aluminium Bronze and 5083 ALU Light Level - 150w 12,000 Lumens NOTE Installation Instruction: The hole cut-out should be mm. For Lamp Maintenance allow 150mm behind the projector lid. Hull thickness range 12 to 75 mm. Electrical Information: 150w - Recommended maximum distance between ballast and projector 10m. Cable - 150w-High temperature silicone 3 core (Part No S00111). For additional information please visit our web site.
5 UL Ti MATE 130 Aluminium Bronze Fixed Screwed Underwater Lights ORDERING NUMBER FOR 230 VOLT 150WATT LIGHTS S00475-V2(H)W2 ORDERING NUMBER FOR 120 VOLT 150WATT LIGHTS S00475-V3(H)W2 UL Ti MATE 130 INSTALLATION (The UL Ti MATE 130 should be no less than 250mm/10 below the water line) Qualified/Approved personnel must be used to carry out installation Cut and prepare a 4 inch / 100 mm clearance hole for the body (16). Coat the flange of the body and the area around the hole with 3M 4200FC sealant then slide the body into the hole. From the inside fit the compensating ring (17) and screw the securing ring (18) up hand tight. Adjust the screws (19) so the compensating ring is flush to the hull and check the sealant has flowed completely around the flange. Do NOT over tighten the screws as this will squeeze the sealant from the surface. Allow the sealant to solidify and remove surplus. Finally tighten the adjustment bolts to 4Nm / 3ft.lbs Note for cored hulls - After cutting, the exposed surfaces of the hole must be finished to form a solid surface through it, thus protecting the internal core of the hull. Maximum hull thickness should not exceed 4.75 inches - 120mm Minimum wall thickness 0.375inches.- 10mm After completing the installation procedure it is highly recmmended to coat the exposed body with antifouling. EARTHING LIGHT FOR CATHODIC PROTECTION-tighten the earth screw on the securing ring so that it bites into the screwed barrel. Check there is continuity to the front face. This prevents galvanic corrosion. OPERATIONAL CONDITIONS AND CONSIDERATIONS The UL Ti MATE 130 is serviced from inside the hull. Allow a minimum of 170mm behind the cable gland for lamp replacements on 150w and 150mm behind the.ignitor on 250w ELECTRICAL INFORMATION CABLE SPECIFICATION TO PROJECTOR 150 Watt High temp silicone three core part number. S WATT Max distance between ballast and projector with -10 meters.ballast power 150 watt ballast 120/230 volt, running current 1.4/0.7.A Ballast will not ignite a hot lamp. The ballast has three attempts to ignite the lamp then will wait for four minutes before repeating the cycle. Do not attempt to remove the glass lens while afloat Part Description Part No 1: Cable S : Projector lid complete S00102-C 3: "O" Ring : Connecting Ring B 5: Body S00475-A 6: Screws (M6X 25 ALU.) : Gasket - NAF A 8: Glass F 9: Glass retaining ring C 10: Comp. ring A 11: Securing ring A 13: Electronic ballast-230 volt V2HW2 13: Electronic ballast-120 volt V3HW2 12: Reflector Tube with Reflector S : Lamp (MSD-150W/70) : Gasket - NAF 000C07-A 16: Cable gland : Screws (M6X 16 S.S.) Recommended Spares Part No Lamp (MSD-150W/70) Glass with gaskets S00279-A Electronic ballast ELECTRONIC BALLAST COMPLETE WITH IP65 ENCLOSURE EARTH TAB AND SCREW LENS FITTING INSTRUCTIONS Check the glass landing surface is clean and apply a suitable silicone grease to the gaskets. Fit the glass, gaskets and retaining ring as shown above. Hand tighten the screws with a 5mm Allen key making sure the glass retaining ring is square. Torque the screws to 6 Nm (4.5ft/lbs) in the sequence shown, check the ring again and re-torque the screws again to the same setting PLEASE REGISTER YOUR PRODUCT WARRANTY DIRECT TO WWW,REGISTER-UWL.COM FOR TECHNICAL INFORMATION PLEASE T@UNDERWATERLIGHTS.COM SALES, PRODUCT INFORMATION AND NEWS GO TO WWW,UNDERWATERLIGHTS.COM UL Ti MATE 130-FIXED
6 UL Ti MATE RANGE - MODEL NUMBER - S02652 underwater lights limited Manufacturers of the Original underwater lights Brand Marine Lighting Products since 1991 DESCRIPTION This is our most popular through-hull submersible marine light IPX8 rated to 10 bar for coastal power boats and some ten thousand have been installed world wide. The light is suitable for installation into GRPfibreglass and wooden hulls and must be installed below the minimum waterline. The boat must be hauled out for installation, although maintenance is carried out from inside the hull. The light has a sealed integral igniter which makes it safer, and allows the ballast to be located away from the bilge area. The latest UL Ti MATE 80 can also be fitted with a wide beam lens. Also available in an extended version. TECHNICAL SPECIFICATION Lamp Type - Xenon bulb Lamp Life Hours - Colour Temp K Voltage / Amp 12VDC/6.4A - 24VDC/2.5.A Glass Lens - Borosilicate glass Classification - Lloyds Approved Material - Aluminium Bronze and 5083 ALU Light Output - 4,800 Lumens NOTE- Installation Instruction: The hole cut-out should be 61 mm. Hull thickness range mm and mm. Recommended distance between lights 1 to 2 metres Electrical Information: Recommend only 2 lights for each power supply cable. See wiring diagram on opposite page. For additional information please visit our web site. 80mm 180mm 40mm
7 UL Ti MATE RANGE - MODEL NUMBER - S02652-V5/V6 underwater lights limited Manufacturers of the Original underwater lights Brand Marine Lighting Products since 1991 WIRING DIAGRAM 24V/V5 WIRING DIAGRAM 12V/V6
8 UL Ti MATE 80 submersible through hull light Xenon with 55 watt Ballast LAMP TYPE - XENON DISCHARGE 55 WATT ORDERING NO FOR 12 VOLT - S02652-V6W5 & 24 VOLT - S02652-V5W5 UL Ti MATE 80 Installation (Maximum hull thickness 60mm) and Operation instructions. Qualified/Approved personnel must be used to carry out installation Before cutting a hole in the hull, check the hull wall thickness is not greater than 60mm. The location of the holes must be below the waterline. After cutting and finishing the hole surface, check the 60mm diameter. UL Ti MATE 80 body (9) can be inserted. Note for cored hulls - After cutting, the exposed surfaces of the hole must be finished to form a solid surface through it. Thus protecting the internal core of the hull. The wall thickness of the hole should not to less than 5mm-0.25inch. Apply 3M-4200FC sealant to the body (9) flange. Slide the body into the hole and from inside the hull put the compensating ring (10) on and screw the case securing ring (11) up hand tight. Gently tighten the adjustment screws (6) so the compensating ring is flush to the hull and the sealant has flowed completely around the flange and hull Do NOT overtighten the bolts as this will squeeze the sealant from the surfaces. Allow the sealant to solidify and remove surplus. Finally tighten the bolts to 4Nm. / 3ft. lbs. Note: Maximum ambiant operating temperature is 55C/131F of the ballast The ballast must be installed a minimun of 24 inches (600 mm) above the bilge. Fit the lamp (5) and assemble the remaining parts to the through-hull submersible marine light. Lightly grease the O rings. When fitting a new lamp make sure the lamp is switched off and bring the ignitor, lamp and reflector tube away and above the bilge to the highest point before changing the lamp. Cautionary Label- Caution: do not operate lights unless totally submerged must be located by the main switch. EARTHING LIGHT FOR CATHODIC PROTECTION-tighten the earth screw on the securing ring so that it bites into the screwed barrel. Check there is continuity to the front face. This prevents galvanic corrosion. After completing the installation procedure it is highly recommended to coat the face of the through-hull submersible marine light with antifouling and bond them to the anodes or a cathodic protection system. Power supply The 12 volt D.C ballast can operate between volts. Start up current is 8 amps and 6.4 amps continuous. The 24 volt D.C ballast can operate between volts. Start up current is 4.5 amps and 2.5 amps continuous. Note a maximum of two lamps can be connected to one cable supply. The correct size cable must be used and the maximum volt drop (1.5 volts) on the cable length should be calculated using the maximum start up current. TM Part Description Part No 1: Ballast 12 vdc 55 watt : Ballast 24 vdc 55 watt Igniter 'O' Ring (40mm) 'O' Ring (50mm) : Xenon lamp 55 watt : Adjustment screws : Gasket : Lens : UL Ti MATE 80 Body S : Compensating ring : Securing ring B 12: Reflector with tube S : Lamp holder securing ring A QT LED 80 CONNECTION POWER SUPPL EARTH EARTH EARTH TAB AND SCREW BALLAST PLUG POSITION PLEASE REGISTER YOUR PRODUCT WARRANTY DIRECT TO WWW,REGISTER-UWL.COM FOR TECHNICAL INFORMATION PLEASE T@UNDERWATERLIGHTS.COM SALES, PRODUCT INFORMATION AND NEWS GO TO WWW,UNDERWATERLIGHTS.COM Ul Ti Mate 80 S
9 UL Ti MATE 80 Extended submersible through hull light Xenon with 55 watt Ballast LAMP TYPE - XENON DISCHARGE 55 WATT ORDERING NO FOR 12 VOLT - S02652-XT-V6W5 & 24 VOLT - S02652-XT-V5W5 UL Ti MATE 80 Extended Installation (Maximum hull thickness 120mm) and Operation instructions. Qualified/Approved personnel must be used to carry out installation Before cutting a hole in the hull, check the hull wall thickness is not greater than 120mm. The location of the holes must be below the waterline. After cutting and finishing the hole surface, check the 60mm diameter. UL Ti MATE 80 body (9) can be inserted. Note for cored hulls - After cutting, the exposed surfaces of the hole must be finished to form a solid surface through it. Thus protecting the internal core of the hull. The wall thickness of the hole should not to less than 5mm-0.25inch. Apply 3M-4200FC sealant to the body (9) flange. Slide the body into the hole and from inside the hull put the compensating ring (10) on and screw the case securing ring (11) up hand tight. Gently tighten the adjustment screws (6) so the compensating ring is flush to the hull and the sealant has flowed completely around the flange and hull Do NOT overtighten the bolts as this will squeeze the sealant from the surfaces. Allow the sealant to solidify and remove surplus. Finally tighten the bolts to 4Nm. / 3ft. lbs. Note: Maximum ambiant operating temperature is 55C/131F of the ballast The ballast must be installed a minimun of 24 inches (600 mm) above the bilge. Fit the lamp (5) and assemble the remaining parts to the through-hull submersible marine light. Lightly grease the O rings. When fitting a new lamp make sure the lamp is switched off and bring the ignitor, lamp and reflector tube away and above the bilge to the highest point before changing the lamp. Cautionary Label- Caution: do not operate lights unless totally submerged must be located by the main switch. After completing the installation procedure it is highly recommended to coat the face of the through-hull submersible marine light with antifouling and bond them to the anodes or a cathodic protection system. Power supply 12 VOLT BALLAST- 12 volts DC- 6.4 amps. : 24 VOLT BALLAST- 24 volts DC- 2.5amps Note a maximum of two lamps can be connected to one cable supply. The correct size cable must be used and the maximum volt drop (1.5 volts) on the cable length should be calculated using the maximum start up current. LAMP CHANGE - To change the lamp undo the grub screw (3) and remove the reflector tube (12). Insert the lamp into the lamp holder (2) and replace the reflector tube (2) and tighten the grub screw (3). TM Part Description Part No 1: Ballast 12 vdc 55 watt : Ballast 24 vdc 55 watt Lamp Holder Grub screw 'O' Ring (50mm) : Xenon lamp 55 watt : Adjustment screws : Gasket : Lens : UL Ti MATE 80 Body S02652-XT 10: Compensating ring : Securing ring B 12: Reflector with tube S02605-XT 13: Lamp holder securing ring A S02605-XT 3 S02605-XT BALLAST PLUG POSITION PLEASE REGISTER YOUR PRODUCT WARRANTY DIRECT TO WWW,REGISTER-UWL.COM FOR TECHNICAL INFORMATION PLEASE T@UNDERWATERLIGHTS.COM SALES, PRODUCT INFORMATION AND NEWS GO TO WWW,UNDERWATERLIGHTS.COM UL Ti MATE 80 Extended - S02652-XT
10 UL Ti MATE RANGE - MODEL NUMBER - S underwater lights limited Manufacturers of the Original underwater lights Brand Marine Lighting Products since 1991 DESCRIPTION The UL Ti MATE 80, 20W LED is a through- hull submersible marine light rated IP68 to 10 bar. The light is suitable for small boats and can be installed into GRP-fiberglass and wooden hulls. It must be installed below the minimum waterline. The boat must be hauled out for installation, although maintenance of the LED is carried out from inside the hull. The LEDs are available in blue, red, green or white. The LED driver is integral with the light. TECHNICAL SPECIFICATION Lamp Type - 7 x single 110 lumen LED- Lamp Life - 30,000 Hours - Colour Temp K Voltage/Amps - 12vdc/1.6 A - 24vdc/0.8 A Glass Lens - Borosilicate glass Classification - Lloyds Approved Material - Aluminium Bronze and 5083 ALU Light Output - 1,400 Lumens NOTE- Installation Instruction The hole cut-out should be 61 mm. Hull thickness range 12-65mm Recommended distance between lights 1 to 2meters. Electrical Information See diagram opposite. The 12/24vdc driver is integral, just connect the red wire to the +VE and black wire to the -VE 12/24vdc power supply. Maximum number of lights on one supply cable TWO For additional information please visit our web site. UL Ti MATE 80 LED 1,400 lumen 82mm 3 60mm 4 122mm - VE BLACK + VE RED POWER SUPPLY 12 VOLTS DRIVER 24 VOLTS DRIVER MAXIMUM 2 LAMPS ON THE SAME SUPPLY CABLE. THE VDC DRIVER CAN OPERATE BETWEEN MIN 10 VDC 10.5 (-5%) 28.5 (+ 5%) MAX 30 VDC Max 2 lamps on the same supply cable 1 8 underwater lights limited TM For sales telephone numbers visit
11 UL Ti MATE 80 Alu-Bronze submersible through hull light 20 Watt LED ORDERING NUMBERS : -S02860 UL Ti MATE 80 Installation (Maximum hull thickness of 65mm) and Operation. Qualified/Approved personnel must be used to carry out installation. Before cutting a hole in the hull, check the hull wall thickness is not greater than 65mm and that the location of the holes are below the waterline. After cutting and finishing the hole surface, check the body (5) can be inserted into the 60mm diameter hole. You are now ready for installation. Note for cored hulls - After cutting, the exposed surfaces of the hole must be finished to form a solid surface through it. Thus protecting the internal core of the hull. The wall thickness of the hole should not to less than 5mm-0.25inch. Apply 3M-4200FC sealant to the body (5) flange. Slide the body into the hole and from inside the hull put the compensating ring (6) on and screw the securing ring (7) up hand tight. Gently tighten the adjustment adjustment screws (2) so the compensating ring is flush to the hull and the sealant has flowed completely around the flange and hull. Do NOT overtighten the screws as this will squeeze the sealant from the surfaces. Allow the sealant to solidify and remove surplus. Finally tighten the bolts to 4Nm. / 3ft. lbs. Fit the lamp and assemble the remaining parts to the UL Ti MATE 80. Lightly grease the O ring and gasket. Cautionary Label- Caution: do not operate lights unless totally submerged must be located by the main switch. After completing the installation procedure it is highly recommended to coat the face of the through-hull submersible marine light with antifouling and bond them to the anodes or a cathodic protection system. EARTHING LIGHT FOR CATHODIC PROTECTION-tighten the earth screw on the securing ring so that it bites into the screwed barrel. Check there is continuity to the front face. This prevents galvanic corrosion. TM Part Description Part No 1. 'O' Ring (50mm dia) Adjusment screws Gasket Glass lens Ultimate 80 Body S Compensating Ring A 7. Securing Ring LED tube S02605-LED 9: Lamp holder securing ring B 82mm 3 60mm 4 122mm UL Ti MATE 80 CONNECTION POWER SUPPLY EARTH EARTH EARTH TAB AND SCREW Power Supply and CONNECTION 20 Watt 12 Volt LED unit requires 1.60 Amps 20 Watt 24 Volt LED unit requires 0.80 Amps Ensure the the polarity of the positive and the negative is correct so that the integral driver is not damaged PLEASE REGISTER YOUR PRODUCT WARRANTY DIRECT TO WWW,REGISTER-UWL.COM FOR TECHNICAL INFORMATION PLEASE T@UNDERWATERLIGHTS.COM SALES, PRODUCT INFORMATION AND NEWS GO TO WWW,UNDERWATERLIGHTS.COM UL Ti MATE 80 AB2-AL
12 QT 80 cute in size big on light Qt LED 80 Installation (Maximum hull thickness 60mm) and Operation instructions. The QT 80, is a through- hull submersible marine light and is delivered ready for installation. Maintenance of the LED is carried out from inside the hull. The light is suitable for installation into GRP-fiberglass and wooden hulls. LED output 5,500 lumens -Colour temperature of 7,200K. Other colours are available also RGB. Qualified/Approved personnel must be used to carry out installation Before cutting a 60mm hole in the hull, check the hull wall thickness is not greater than 60mm. The location of the holes must be below the waterline. After finishing the hole surface, check the Body (1) can be inserted. Note for cored hulls - After cutting, the exposed surfaces of the hole must be finished to form a solid surface through it. Thus protecting the internal core of the hull. The wall thickness of the hole should not to less than 5mm-0.25inch. Apply 3M-4200FC sealant to the Body (1) flange. Slide the body into the hole and from inside the hull put the compensating ring (2) on and screw the securing ring (3) up hand tight. Gently tighten the adjustment screws (6) so the compensating ring is flush to the hull and the sealant has flowed completely around the flange and hull Do NOT overtighten the bolts as this will squeeze the sealant from the surfaces. Allow the sealant to solidify and remove surplus. Finally tighten the bolts to 4Nm. / 3ft. lbs. When all parts are assembled and the sealant has cured tighten the cover (5) to secure the heatsink (4) into the body. If this is not done it will cause overheating of the LED and the LED could fail. EARTHING LIGHT FOR CATHODIC PROTECTION-tighten the earth screw on the securing ring so that it bites into the screwed barrel. Check there is continuity to the front face. This prevents galvanic corrosion. Cautionary Label- Caution: do not operate lights unless totally submerged must be located by the main switch. After completing the installation procedure it is highly recommended to coat the BODY (1) face with antifouling and bond them to the anodes or a cathodic protection system. Part Description 1: Body 2: Compensating ring 3: Securing ring 4: LED Heat sink 5: Screwed cover 6: Adjustment screws 7: Nitrile 'O' ring 80MM 1-BODY FOR WIDE LENS 2-COMPENSATING RING 3-SECURING RING 4-LED HEAT SINK 5-COVER 7-'O' RING 60MM 1-BODY FOR WIDE LENS 2-COMPENSATING RING 3-SECURING RING 4-LED HEAT SINK 5-COVER 7-'O' RING 6-M6 CAP HEAD BOLT 84MM EARTH TAB AND SCREW Drivers for Qt 80 Supply 230 vac Output 24vdc - 3.3amps Supply 24-48dc - Output 24vdc - 3.3amps TECHNICAL SPECIFICATION Part No QTD E QTD E Lamp types - Single LED chip- 5,500 lm- 7,200K (Cool White) Also available in blue, green, and red 65 DEG 80 DEG Qt LED 80 & NARROW BEAM (65deg) LUX CHART (lux) FLAT (130deg) LUX CHART 1m 2m 3m (lux) 5,500 LUMEN 5,500 LUMEN Qt LED 80 & WIDE BEAM (80deg) LUX CHART 1M M M QT LED 80 CONNECTION EARTH POWER SUPPL EARTH VDC. LED Driver - Min 22- Max 28vdc maximum current 3.3amps. Glass lens - Borosilicate wide beam glass as standard Bezel Material - Aluminium Bronze & 5083 ALU. 24 dc DRIVER QTD E LED lamp life - 20, C PLEASE REGISTER YOUR PRODUCT WARRANTY DIRECT TO SALES, PRODUCT INFORMATION AND NEWS GO TO QT LED WWW,QTLED.COM
13 DESCRIPTION The QT 80, is a through- hull submersible marine light tested at front of glass to IP68 at 10 bar. The light is suitable for installation into GRP-fiberglass and wooden hulls. There are three types of lenses for different beam widths - the standard is wide 95 deg, flat 130deg and narrow 70deg. The standard LED produces 5,500 lumens -Colour temperature of 7,200K. Other colours are available, also RGB. The light must be installed below the minimum waterline. The boat must be out of the water for installation. Maintenance of the LED is carried out from inside the hull. The LED driver is fitted into an enclosure and is mounted remotely. Note this light can be driven at low outputs to suit boat battery power. TECHNICAL SPECIFICATION Lamp types - Single LED chip- 5,500 lm- 7,200K (Cool White) QT 80 cute in size big on light Mains Power LED Driver vac. Output 24vdc, maximum current 3.3amps Order No. QTD E 80MM 1-BODY FOR WIDE LENS 6-M6 CAP HEAD BOLT 84MM 2-COMPENSATING RING 3-SECURING RING 4-LED HEAT SINK 5-COVER 7-'O' RING Standard QT LED 80 - with wide beam lens LED Output 5,500 lumen, 7,200K Order Number QT LED-80-24vdc 60MM VDC. LED Driver - Min 22- Max 28vdc maximum current 3.3 amps Order No. QTD E Glass lens - Borosilicate wide beam glass as standard Bezel Material - Aluminium Bronze & 5083 ALU. LED lamp life - 20, C NOTE- Installation Instruction The hole cut-out should be 61 mm. Hull thickness range 12-65mm Recommended distance between lights 1 to 2meters. The light is supplied with 3 meters of 6mm diameter, 2 core marine grade cable. For VDC power supply the maximum number of lights on one supply cable of AWG 10 is TWO (See wiring diagram opposite) For additional information please visit our web site. Earthing instruction After the light has been installed tighten the earth screw on the securing ring sothat it bites into the screwed barrel. Check there is continuity from the earth tab to the front face of the light. This is very important to stop galvanic corrosion of the front face 65 DEG 80 DEG PLEASE REGISTER YOUR PRODUCT WARRANTY DIRECT TO Qt LED 80 & NARROW BEAM (65deg) LUX CHART (lux) FLAT (130deg) LUX CHART 1m 2m 3m (lux) 5,500 LUMEN 5,500 LUMEN Qt LED 80 & WIDE BEAM (80deg) LUX CHART AWG 10 - CABLE Qt LED 80 LED 1M M M LUX CHART 24 VDC POWER SUPPLY SALES, PRODUCT INFORMATION AND NEWS GO TO QT LED WWW,QTLED.COM
14 UL Ti MATE RANGE - MODEL - UL Ti MATE 75 FIXED 150W underwater lights limited Manufacturers of the Original underwater lights Brand Marine Lighting Products since 1991 DESCRIPTION The UL Ti MATE 75 Fixed is a through-hull submersible marine light for welding into aluminium and steel hulls. Maintenance of the light is carried out from inside the hull. It does not include the SA 'Super Adjustable' unit and has been introduced to compete fairly with other fixed lights on the market. The lens aperture is exactly the same as the SA to give the same maximum light output. This new light is also shorter in length to the SA unit so that it is easier to fit into those small areas. We advise that the light be installed minimum 250mm below the waterline when the yacht is loaded with 50% fuel and 50% water, and that the light be angled 15 degrees downwards. To achieve this there are 3 models- Flush, 30 degree and 50 degree. The stainless steel model comes as standard with Ice Class Lloyds Approval and has been pressurised to 80 bar. The aluminium model is IPX8 to 10 bar. The range is also GL Approved. TECHNICAL SPECIFICATION Lamp Type - MSD Metal Halide 150w Lamp Life Hours - Colour Temp K Voltage/Amps watt 120(V3)/230(V2) - 1.4/0.7.A Ballast watt electronic in IP 65 Enclosure Glass Lens - Borosilicate glass Material - Steel and 5083 ALU Light Level - 150w 12,000 Lumens UL Ti MATE degree NOTE Installation Instruction: The hole cut-out should be cut to suit the insert angle. Maximum hull plate thickness should be 12mm for the flush and 20mm for the 30 & 50 degree. For Lamp Maintenance allow 60mm behind the cable gland. Electrical Information: 150w - Recommended maximum distance between ballast and projector 10m. Cable - High temp. silicone 3 core (Part No S00111). For additional information please visit our web site. For sales telephone numbers visit 140mm 120mm 120mm 75mm 105mm 27mm 40mm 168mm 168mm 168mm 115mm Order Number Flush-STEEL S ICE-V2/V3W2 Order Number Flush-ALU S V2/V3W2 115mm Order Number 30 deg. STEEL S ICE-V2/V3W2 Order Number 30 deg. ALU S V2/V3W2 115mm Order Number 50 deg. STEEL S ICE-V2/V3W2 Order Number 50 deg. ALU S V2/V3W2 underwater lights limited TM
15 UL Ti MATE L STAINLESS STEEL AND 5083 ALUMINIUM ORDERING NUMBERS FLUSH - S ICE. 30 DEG - S ICE. 50 DEG -S ICE FLUSH - S DEG - S DEG -S WITH 120 (V3) / 230 (V2) VOLT BALLAST AND 150W (W2) WATT LAMP. OPERATIONAL CONDITIONS AND CONSIDERATIONS The UL Ti MATE 75 is serviced from inside the hull. Allow access for maintenance and space for ventilation. Do not use the LIGHT in dry-dock or out of the water Allow a minimum of 70mm behind the projector lid (item 2) for lamp replacements. UL Ti MATE 75 to be fitted 250mm below the yachts water line when loaded with 50% fuel and 50% freshwater onboard. ELECTRICAL INFORMATION Cable specification from electronic ballast to projector (Pt.No. S00111) Shielded 3 core, Temperature -60C to +180C, Voltage 2000 volts. Maximum distance between ballast and projector with the shield earthed 10 meters. Ballast power 120/230 volt 150 watt ballast - running current 1.4/0.7A Ballast will not ignite a hot lamp. The ballast has a cycle of three attempts to ignite the lamp then will wait for four minutes before repeating the cycle. Install ballast in a dry space. Maximum ambient temperature 40C Do not attempt to remove the glass lens while afloat. The projector must be correctly assembled with lid secured to the UL Ti MATE 75 whilst afloat. ELECTRONIC BALLAST Part Description Part No 1; Projector Cable S ; Projector lid complete S00C102-B 3; "O" Ring ; Projector case B 5; Lamp (150w MSD) ; Reflector C 7; AB2 Connecting ring A 8; Gaskets A 8A; Gaskets 000C07-B 9; S.S.316L Body 003XX-75 9; Alu 5083 Body 006XX-75 10; S.S. M6 socket screws ; Ti. M6 socket screws SC 11; S.S. Glass retaining ring ICE 75B 11; Alu Glass retaining ring B 12; Gaskets A 13; Glass ; Electronic ballast 120V V3-H 14; Electronic ballast 230V V2-H 14A; Enclosure A Recommended Spares Part No Lamp Glass with gaskets S00281 Electronic ballast S DEGREE FLUSH 140 mm 50 DEGREE LENS FITTING INSTRUCTIONS Check the glass landing surface is clean and apply a suitable silicone grease to the gaskets. Fit the glass, gaskets and retaining ring as shown above. Hand tighten the screws with a 5mm Allen key making sure the glass retaining ring is square. Torque settings for all retaining screws - 10 Nm (7.5 ft/lbs). Torque the screws in the sequence shown. Check the ring again and re-torque the screws again to the same torque setting. PLEASE REGISTER YOUR PRODUCT WARRANTY DIRECT TO WWW,REGISTER-UWL.COM FOR TECHNICAL INFORMATION PLEASE T@UNDERWATERLIGHTS.COM SALES, PRODUCT INFORMATION AND NEWS GO TO WWW,UNDERWATERLIGHTS.COM B ICE-75B UL Ti MATE 75 ICE S.S + UL Ti MATE 75 ALU
16 UL Ti MATE RANGE - MODEL - UL Ti MATE 75 SA 150W-250W underwater lights limited Manufacturers of the Original underwater lights Brand Marine Lighting Products since 1991 DESCRIPTION This is a through-hull submersible marine light for welding into aluminium and steel hulls. Maintenance of the light is carried out from inside the hull. Our patent pending internal SA ( Super Adjustable) unit allows the beam angle to be varied from a narrow to wide beam, and to universally move the beam direction by 20 degrees from within the projector housing. We advise that the light be installed 250mm below the minimum waterline when the yacht is loaded with 50% fuel and 50% water, and that the light be angled 15 degrees downwards. To achieve this there are 3 models- Flush, 30 degree and 50 degree. The UL Ti MATE 75 SA has a larger aperture which increases the light output by 25%. The stainless steel model comes as standard with Ice Class Lloyds Approval and has been pressurised to 80 bar. The aluminium model is IPX8 to 10 bar. The range is also GL Approved. TECHNICAL SPECIFICATION Order Number Flush-STEEL S SA-ICE-V2/V3W2- W1 Lamp Type MSD Metal Halide 150w-250w Lamp Life Hours - Colour Temp K Voltage/Amps watt 120(V3)/230(V2) - 1.4/0.7.A Voltage/Amps watt- 198/264vac- 1.2A Glass Lens - Borosilicate glass Material - Steel and 5083 ALU Light Level -150w 12,000 Lumens - 250w 19,000 Lumens NOTE Installation Instruction: The hole cut-out should be cut to suit the insert angle. Maximum hull plate thickness should be 12mm for the flush and 20mm for the 30 & 50 degree. For Lamp Maintenance allow 170mm behind the cable gland. Electrical Information: 150w - Recommended maximum distance between ballast and projector 10m. 250w - Recommended maximum distance between ballast and projector 25m. Cable - 150w-250w High temp. silicone 3 core (Part No S00111, 0.75). For additional information please visit our web site. For sales telephone numbers visit 140mm UL Ti MATE 75 SA STEEL Flush 120mm 120mm 27mm 75mm 105mm UL Ti MATE 75 SA ALU 30 degree 210mm Order Number Flush-ALU S SA-V2/V3W2- W1 210mm Order Number 30 deg. STEEL S SA-ICE-V2/V3W2-W1 Order Number 30 deg. ALU S SA-V2/V3W2-W1 210mm 40mm Order Number 50 deg. STEEL S SA-ICE-V2/V3W2-W1 Order Number 50 deg. ALU S SA-V2/V3W2-W1 124mm 124mm 124mm underwater lights limited TM
17 316 S.S. UL Ti MATE 75 SA-ICE submersible through hull light ORDERING NUMBERS FLUSH - S SA-ICE. 30 DEG - S SA-ICE. 50 DEG -S SA-1CE WITH 120 (V3) / 230 (V2) VOLT BALLAST AND 150W (W2) OR 250W (V2,W1) WATT LAMP. OPERATIONAL CONDITIONS AND CONSIDERATIONS The UL Ti MATE 75 SA is serviced from inside the hull. Do not attempt to remove the glass lens while afloat. Allow access for maintenance and space for ventilation. The projector must be correctly assembled with lid Do not use the UL Ti MATE in dry-dock or out of water secured to the UL Ti MATE whilst afloat. Allow a minimum of 170mm behind the cable gland for lamp replacements on 150w and 150mm behind the.ignitor on 250w. UL Ti MATE to be fitted a minimumof 250mm below the yachts water line when loaded with 50% fuel and 50% freshwater onboard ELECTRICAL INFORMATION 150 WATT Maximum distance between ballast and projector -10 meters 250 WATT Maximum distance between ballast and projector - 10 meters. Ballast power 150 watt ballast 120/230 volt, running current 1.4/0.7.A Ballast power 250 watt ballast 230 volt, running current 1.2.A Ballast will not ignite a hot lamp. The ballast has a cycle of three atempts to ignite the lamp then will wait for six minutes before repeating the cycle. Ballast must be installed in dry space. Maximum ambient temperature 40C DO NOT swich ballast on and off. CABLE SPECIFICATION TO PROJECTOR High tempereture (180C) silicone screened three core. Cable diameter 9mm PART NUMBER S EWKF 3G0, & 230 VOLTAGE SUPPLY FOR 150 & 250 WATT ELECTRONIC BALLAST COMPLETE WITH ENCLOSURE. TM Part Description 75-SA Part No 1: Projector lid securing plate B 2: M6 Nut : 'O' Ring : Gasket NAF A 5: Connecting ring C 6: Lamp holder screw : Lamp holder (250W) : Lamp holder (150W) : Reflector collar bush A 9: M4 Lock nut : Lamp (250W) : Lamp (150W) : Reflector adjustment rod : Reflector complete S : Gasket NAF A 14: AB2 Connecting ring A 15: Projector barrel C 16: Gasket NAF 000C07-B 30: Glass gaskets NAF A 31: Glass lens : Body Flush (s.s) S ICE 40: Body 50 deg (s.s.) S B ICE 41: Body 30 deg (s.s.) S ICE 42: Glass retaining ring ICE 75B 43: Cap head screws Part Description 75-SA Part No 22: Gland : Projector cover E 24: Ballast 250 watt 230v S00820-V2 W1 24: Ballast 150 watt 230v S00800-V2W2 24: Ballast 150 watt 120v S00800-V3W2 Recommended Spares Part No Lamp ( 250w = W1 ) Lamp ( 150w = W2 ) Glass with gaskets S00281-A Ballast LENS FITTING INSTRUCTIONS Check the glass landing surface is clean and apply a suitable silicone grease to the gaskets. Fit the glass, gaskets and retaining ring as shown above. Hand tighten the screws with a 5mm Allen key making sure the glass retaining ring is square. Torque settings for all retaining screws - 10 Nm (7.5 ft/lbs). Torque the screws in the sequence shown. Check the ring again and re-torque the screws again to the same torque setting. PLEASE REGISTER YOUR PRODUCT WARRANTY DIRECT TO WWW,REGISTER-UWL.COM FOR TECHNICAL INFORMATION PLEASE T@UNDERWATERLIGHTS.COM SALES, PRODUCT INFORMATION AND NEWS GO TO WWW,UNDERWATERLIGHTS.COM UL Ti MATE 75-SA-ICE-SS-H & 250 watt S ICE (40) S ICE (41) FLUSH S ICE (39)
18 5083 ALU UL Ti MATE 75 SA submersible through hull light ORDERING NUMBERS FLUSH - S SA. 30 DEG - S SA. 50 DEG - S SA WITH 120 (V3) / 230 (V2) VOLT BALLAST AND 150W (W2) OR 250W (V2,W1) WATT LAMP. OPERATIONAL CONDITIONS AND CONSIDERATIONS The UL Ti MATE 75 SA is serviced from inside the hull. Do not attempt to remove the glass lens while afloat. Allow access for maintenance and space for ventilation. The projector must be correctly assembled with lid Do not use the UL Ti MATE in dry-dock or out of water secured to the UL Ti MATE whilst afloat. Allow a minimum of 170mm behind the cable gland for...lamp replacements on 150w and 150mm behind the.ignitor...on 250w UL Ti MATE to be fitted 250mm below the yachts water line when loaded with 50% fuel and 50% freshwater onboard. ELECTRICAL INFORMATION 150 WATT Maximum distance between ballast and projector -10meters 250 WATT Maximum distance between ballast and projector - 25 meters. Ballast power 150 watt ballast 120/230 volt, running current 1.4/0.7.A Ballast power 250 watt ballast 230 volt, running current 1.2.A Ballast will not ignite a hot lamp. The ballast has a cycle of three atempts to ignite the lamp then will wait for six minutes before repeating the cycle. Ballast must be installed in dry space. Maximum ambient tmperature 40C DO NOT switch ballast on and off. CABLE SPECIFICATION TO PROJECT High temp silicone three core part number. S WATT ELECTRONIC BALLAST COMPLETE WITH ENCLOSURE. SEE BALLAST SHEET FOR FURTHER INFORMATION TM Part Description 75-SA Part No 1: Projector lid securing plate B 2: M6 Nut : 'O' Ring : Gasket NAF A 5: Connecting ring C 6: Lamp holder screw : Lamp holder (250W) : Lamp holder (150W) : Reflector collar bush A 9: M4 Lock nut : Lamp (250W) : Lamp (150W) : Reflector adjustment rod : Reflector complete S : Gasket NAF A 14: AB2 Connecting ring A 15: Projector barrel D 16: Gasket NAF 000C07-B 30: Glass gaskets NAF A 31: Glass lens : Body Flush (alu) S : Body 50 deg (alu) S B 41: Body 30 deg (alu) S : Glass retaining ring B 43: Cap head screws SC Part Description 75-SA Part No 22: Gland : Projector cover E 24: Ballast 250 watt S00820-V2W1 24: Ballast 150 watt 230v S00800-V2W2 24: Ballast 150 watt 120v S00800-V3W2 Recommended Spares Part No Lamp ( 250w = W1 ) Lamp ( 150w = W2 ) Glass with gaskets S00281-A Ballast S00801-V2/V3 S watt FLUSH S S LENS FITTING INSTRUCTIONS Check the glass landing surface is clean and apply a suitable silicone grease to the gaskets. Fit the glass, gaskets and retaining ring as shown above. Hand tighten the screws with a 5mm Allen key making sure the glass retaining ring is square. Torque settings for all retaining screws - 10 Nm (7.5 ft/lbs). Torque the screws in the sequence shown. Check the ring again and re-torque the screws again to the same torque setting. PLEASE REGISTER YOUR PRODUCT WARRANTY DIRECT TO WWW,REGISTER-UWL.COM FOR TECHNICAL INFORMATION PLEASE T@UNDERWATERLIGHTS.COM SALES, PRODUCT INFORMATION AND NEWS GO TO WWW,UNDERWATERLIGHTS.COM UL Ti MATE 75-SA-ALU-H
75- Retro. IPX8 Underwater RATED. underwater lights limited TM. CUTE on size BIG on light. Aluminium / Steel.
underwater lights limited TM Manufacturer of the original underwater lights TM Brand marine lighting products since 1991. 75- Retro cute on size big on light Aluminium / Steel 30 meter + Max 20,000 *The
More information* * 30 meter + Max 2,000 6, degrees. Underwater
* * * * * 30 meter + Max 2,000 6,500 90 degrees Underwater - Technical QT- QT- RGB W Lumens,000 Kelvin 6,500 Typical LED Life Expectancy 40,000 hrs 40,000 hrs Min-Max Operating Voltage 110-240V AC 110-240V
More information130-RGB+W. underwater lights limited TM. IPX8 Underwater RATED. CUTE on size BIG on light. GRP and WOOD. 20 meter + N.
Manufacturer of the original underwater lights marine lighting products since 1991. 130-RGB+W cute on size big on light GRP and WOOD 20 meter + N.A *The QT-130 RGB+W LED underwater light uses a four channel
More informationSV10 LED. The US manufactured SV10 LED is. SV10 LED technical specifications
The US manufactured SV10 LED is the brightest thru hull LED underwater light available to owners of GRP and wood boats. The industry leading SV10 combines the unique qualities of the latest high density
More informationSV14 technical specifications
aluminum weld in underwater light SV14 T he Sea Vision SV14 weld in model for aluminum hulls can be installed in the transom or the hull, it utilizes a 150 watt HID metal halide lamp and 110-230 volt AC
More informationSV38-250w. SV38 technical specifications
SV38-250w The Sea Vision SV38 weld in tank light model for aluminum/steel hulls can be installed in the transom or the hull, it utilizes a 250 watt HID metal halide lamp and 110-230 volt AC power. The
More informationSingle Colour Light. TIX202 Interchangeable Flush Fit Thru-Hull Light. Installation and Operation Guide. Rev
Single Colour Light TIX202 Interchangeable Flush Fit Thru-Hull Light Installation and Operation Guide Rev 3 45-0038 Congratulations! You have purchased a LUMISHORE advanced technology LED underwater light.
More informationSingle Colour Light. TIX301 Interchangeable Flush Fit Thru-Hull Light. Installation and Operation Guide
Single Colour Light TIX301 Interchangeable Flush Fit Thru-Hull Light Installation and Operation Guide Congratulations! You have purchased a LUMISHORE advanced technology LED underwater light. Every care
More informationNeptune X6 12/24V SAE 316L Stainless Steel Low Profile Through-Hull Mounted Underwater LED Light Manual
Neptune X6 12/24V SAE 316L Stainless Steel Low Profile Through-Hull Mounted Underwater LED Light Manual Thank you for purchasing Dr. LED s Neptune X6 underwater LED light. This 1500+ lumen Neptune X6 underwater
More informationINSTRUCTION MANUAL WARNING
OLDHAM GT CAP LAMP SYSTEM The Powerful Choice INSTRUCTION MANUAL WARNING This manual, including the warnings and cautions inside, must be read and followed carefully by all persons who use or maintain
More informationBluefin Led Underwater lights.
Bluefin Led Underwater lights. P24 Single/Dual and Colourchange Installation manual. Thank you for choosing Bluefin LED underwater lights, our products have been designed and tested rigorously to ensure
More informationBluefin Led Underwater lights.
Bluefin Led Underwater lights. V12/V24CC Installation manual. Thank you for choosing Bluefin LED underwater lights, our products have been designed and tested rigorously to ensure the optimum performance
More informationTHX 402, THX 802 & THX 1602 Thru-Hull Light Lumishore SUPRA (dual colour) light Installation and Operating Guide
SUPRA Thru-Hull Integrated System THX, THX & THX Thru-Hull Light Lumishore SUPRA (dual colour) light Installation and Operating Guide Congratulations! You have purchased a LUMISHORE advanced technology
More informationBluefin Led Underwater lights.
Bluefin Led Underwater lights. P6N/P6CC Installation manual. Thank you for choosing Bluefin LED underwater lights, our products have been designed and tested rigorously to ensure optimum performance and
More informationSurface Mount e-lites
Surface Mount e-lites SMX90-CS Colour-SELECT Lights Installation and Operating Guide SMX90-CCP-2 Congratulations! You have purchased a LUMISHORE advanced LED technology underwater lighting system. Every
More information4000 SYSTEM OPERATING MANUAL
4000 SYSTEM OPERATING MANUAL REV 1.4 COPYRIGHT 1996 Xenotech, Inc. PAGE 1 INSTRUCTIONS FOR REMOVING AND INSTALLING A TYPE XT XENON BULB IN A BL4000 FIXTURE NOTE FAMILIARIZE YOURSELF WITH THE LOCATION AND
More informationFlex Tube. User guide
Flex Tube User guide CONTENTS INTRODUCTION...2 Welcome 2 Safety 2 INSTALLATION...3 Flex Tube orientation 3 Bending a Flex Tube 4 Cutting a Flex Tube 4 Connection and mounting kits 5 Feed cable kit 5 End
More informationBL7000 SYSTEM OPERATING MANUAL
BL7000 SYSTEM OPERATING MANUAL REV 2.0 208 / 230V COPYRIGHT 1995 Xenotech, Inc. PAGE 1 POWER INPUT CONNECTOR WIRING INSTRUCTIONS THE INPUT POWER REQUIREMENTS FOR A 7 KW POWER SUPPLY ARE AS FOLLOWS. VOLTAGE
More information1000 Watt Metal Halide Light - Class 1 Division 2 Groups A-D - T3b Temperature - 110,000 lumens
1000 Watt Metal Halide Light - Class 1 Division 2 Groups A-D - T3b Temperature - 110,000 lumens Part #: HALPRM-1000WMH Made in the USA The extremely durable Larson Electronics HALPRM-1000WMH metal halide
More informationAll Bluefin Led lights are water tested so please be aware there may be moisture present on the light.
Bluefin LED Underwater lights. GW16IFM/GW20IFM/GW48CCIFM Installation manual. Thank you for choosing Bluefin LED underwater lights, our products have been designed and tested to ensure optimum performance
More informationIIC wellglass luminaires for low energy, halogen and incandescent lamps flameproof
IIC wellglass luminaires for low energy, halogen and incandescent lamps flameproof Zone 1 & 2-21 & 22 ATEX IEC EC II2G/D IK 08 99 EEx d IIC T6-T5-T4-T3 T = 75 C to 135 C IP 66 0947 36 wellglass luminaire
More informationTHX120-CCP. Colour-CHANGE Lights THX120-CCP Thru-Hull Installation and Operation Guide
THX120-CCP Colour-CHANGE Lights THX120-CCP Thru-Hull Installation and Operation Guide Congratulations! You have purchased a LUMISHORE advanced technology LED underwater light. Every care has been taken
More informationTIX 402, TIX 802 & TIX 1602 Thru-Hull Light Lumishore SUPRA (dual colour) light Installation and Operating Guide
SUPRA Thru-Hull Integrated System TIX, TIX & TIX Thru-Hull Light Lumishore SUPRA (dual colour) light Installation and Operating Guide Congratulations! You have purchased a LUMISHORE advanced technology
More informationTIX402 EOS Installation and Operating Guide
TIX402 EOS Integrated System TIX402 EOS Installation and Operating Guide Congratulations! You have purchased a LUMISHORE advanced LED technology underwater lighting system. Every care has been taken to
More informationRCL-600A PRODUCT SUPPORT MANUAL. Y Rev. B. Remote Control Searchlight with Joystick Remote Control Panel. Product No.
PRODUCT SUPPORT MANUAL Y1-03-0139 Rev. B RCL-600A Product No. 1941 & 1943 Remote Control Searchlight with Joystick Remote Control Panel ACR Electronics, Inc. 5757 Ravenswood Road Fort Lauderdale, Fl 33312
More informationAFL FLOODLIGHT SERIES
AFL FLOODLIGHT SERIES A FL Flood Lighting for Hazardous Locations Class I, Division 2, Groups A, B, C & D UL 844 Hazardous Locations UL 598A Marine Outside Type Zone 2, Groups IIA, IIB & IIC CUL Cast Aluminum
More informationLight Source User Guide
Light Source User Guide Compact Light Source Range Models covered by this manual: UFO 70/150 CG Glass, White Light - 240V UFO 70/150 CP Plastic, White Light - 240V UFO 70/150 CGC Glass, Colour Wheel (continuous)
More informationUnderstanding the Complexities of Specifying LED Luminaires. It s no longer a Bulb in a Box It s an LED TV on a Pole
Understanding the Complexities of Specifying LED Luminaires It s no longer a Bulb in a Box It s an LED TV on a Pole Legacy Technology Lamps and Ballasts All components are built and rated individually
More information4.6. Ex-Floodlights for high-pressure discharge lamps, series FZD 04 / FZD EN. (Zone 1, 2, 21, 22)
.6 Ex-Floodlights for high-pressure discharge lamps, series FZD 0 / FZD EN (Zone 1, 2, 21, 22) The maintenance- and installation-friendly FZD 0 floodlights for harsh operating conditions Due to the spatial
More information96W Ultraviolet LED Light Bar - Submersible Underwater Light 'L X 200'W Spot VDC
96W Ultraviolet LED Light Bar - Submersible Underwater Light - 1100'L X 200'W Spot - 9-42VDC Part #: LEDXUL-32E-UV Page: 1 Buy American Compliant The LEDXUL-32E-UV from Larson Electronics is an Ultraviolet
More informationELLIPTICAL REFLECTORS
ELLIPTICAL REFLECTORS The Short Arc Gap USHIO s Sōlarc single-ended lamps allow the equipment designer to capitalize on the lamp s unique short arc length. At 1.27mm, with a peak luminance at the cathode,
More informationBluefin Led Underwater lights.
Bluefin Led Underwater lights. P3 Installation manual. Thank you for choosing Bluefin LED underwater lights, our products have been designed and tested rigorously to ensure optimum performance and longevity.
More informationBulb Replacement REPLACING BULBS
Bulb Replacement REPLACING BULBS Check the operation of all exterior lamps before you drive the vehicle. Caution: Before attempting to replace a bulb, ensure that both the affected lamp and the vehicle's
More informationTECHNICAL MANUAL. 300RCB Searchlight and Control System. Den Haan Rotterdam
TECHNICAL MANUAL 300RCB Searchlight and Control System SINCE 1922 Den Haan Rotterdam (Intentionally blank page) 2 ! Safety notes: Turn power off before inspection, installation or removal Keep combustible
More informationInstallation Procedures
Installation Procedures Ziza Interior Lighting Package Installation for BMW E38 This tutorial is provided as a courtesy by ECS Tuning. Proper service and repair procedures are vital to the safe, reliable
More informationperformance & comfort
Blend performance & comfort in a downlight. CL-DL-VB CALCULITE LED " Total height of Light engine + Reflector ¼" mm PHILIPS LIGHTOLIER, CALCULITE, PROFESSIONAL-GRADE DOWNLIGHTING, LED " ROUND APERTURE
More information4.5. Ex Floodlights for high-pressure discharge lamps, series PX 04 and FLT 10. (Zone 1, 2, 21, 22)
.5 Ex Floodlights for high-pressure discharge lamps, series PX 0 and FLT 10 (Zone 1, 2, 21, 22) The powerful floodlights for harsh environments Thanks to the high degree of protection IP66, the robust
More information4.7. Ex-Floodlights for high-pressure discharge lamps, series FZD 04 (Zone 1, 2, 21, 22)
.7 Ex-Floodlights for high-pressure discharge lamps, series FZD 0 (Zone 1, 2, 21, 22) The maintenance- and installation-friendly FZD 0 floodlights for harsh operating conditions Due to the spatial separation
More informationUltraSystem Series II INSTALLATION MANUAL PARTNERED WITH
UltraSystem Series II INSTALLATION MANUAL PARTNERED WITH CONTENTS Important information. page 1 Planning the installation. page 2 Transducer positioning. page 3-7 Transducer installation. page 8-10 Control
More informationHID Flashlight - 15 Watt lumens - 90 minute run time battery
HID Flashlight - 15 Watt - 1000 lumens - 90 minute run time battery Part #: FL-15-HID Page: 1 Buy American Compliant The Larson Electronics FL-15-HID Handheld Searchlight is a powerful HID searchlight
More informationSAFJ LED SERIES S A L E D. Hazardous Location Compact LED
SAFJ LED SERIES Hazardous Location Compact LED Class I, Division 2, Groups A, B, C, & D Class II, Division 1 & 2, Groups E & F Class III Simultaneous Presence Enclosed & Gasketed Wet Locations NEMA 3R,
More informationUnderwater LED Light to 60 meters - Aluminum Housing - 12 Watts Lumens - 10 Inch Cable
Underwater LED Light to 60 meters - Aluminum Housing - 12 Watts - 720 Lumens - 10 Inch Cable Part #: LEDEUL4-10ST Made in the USA NSN for this product: 6210-01-647-7649, Light Emitting Diode The LEDEUL4-10ST
More informationMODELS: SPL-12W, SPL-12B, SPL-12C IMPORTANT! READ THESE INSTRUCTIONS BEFORE INSTALLING AND USING THIS PRODUCT.
502-2 & 503-2 Instructions instructions marinco.com Installing and Using the Precision Spotlight MODELS: SPL-12W, SPL-12B, SPL-12C IMPORTANT! READ THESE INSTRUCTIONS BEFORE INSTALLING AND USING THIS PRODUCT.
More informationTIX 802 & TIX 1602 Thru-Hull Light Lumishore EOS Full Colour Change light Installation and Operating Guide
EOS Thru-Hull Integrated System TIX & TIX Thru-Hull Light Lumishore EOS Full Colour Change light Installation and Operating Guide Congratulations! You have purchased a LUMISHORE advanced technology underwater
More informationLED Dome Light VDC - IP67 - Dimmable - Dual Color
LED Dome Light - 10-30VDC - IP67 - Dimmable - Dual Color Part #: LED-DL290 Buy American Compliant The LED-DL290 LED Flush Mount Down Light is designed as an extremely efficient and versatile lighting solution
More informationcoop erat ive Flood Lights 50W Flood Light GLC-ASFL-50W-1 PERFORMANCE LED Chip Beam Angle 70 Lumen Maintenance Power Factor EMI ENVIRONMENTAL
GreenLight coop erat ive Product Specifications Flood Lights 0W Flood Light GLC-ASFL-0W-1 Flexible, modular design Multiple choice of optical lenses PERFORMANCE LED Chip CREE XT-E Lumen Output (IES),0
More informationPeristaltic Pump Operating Instructions
Peristaltic Pump Operating Model 410 IMPORTANT Pump is water resistant but not waterproof. Do not submerge in water. Pumping rates will decrease as the amount of lift increases. Remove tubing when stored.
More informationNIOB-2 2" BWF IOLITE TRIMS
NIOB-2 2" BWF IOLITE TRIMS New Construction or Remodel Housing Required Source: LED, 14 Watts, 8 Lumens Nora Lighting s 2" Iolite BWF trims are small aperture downlights that can be specified for use in
More informationHPP1 MK5 Owner s Manual
J Wolmarans Page 1 2016/09/15 Page 1 of 9 TABLE OF CONTENTS Page 1 Introduction...2 2 Models...2 3 Safety warnings...3 4 Contents...3 5 Installation...3 5.1 Mounting the unit:...3 5.2 Connecting the battery:...3
More informationA-BEAM LIGHT. Instruction & Safety Information. Design by Thomas Housden. Dimensions L1600/1800mm H77mm, W51mm. Weight 9-10 KG
2017 Design by Thomas Housden A-BEAM LIGHT Dimensions L1600/1800mm H77mm, W51mm Weight 9-10 KG Lamp Type 12V DC LED 20W per metre 1284-1345 lumen per metre 2700K or 3000K colour temp IP40 Hand & Eye Studio
More informationSMX 22, SMX52 & SMX 102 Installation and Operating Guide
SUPRA Surface Mount Integrated System SMX, SMX5 & SMX Installation and Operating Guide Congratulations! You have purchased a LUMISHORE advanced LED technology underwater lighting system. Every care has
More informationECLIPSE CCFL ANGEL EYES FITTING GUIDE COURTESY OF CHROMELINE DESIGN
ECLIPSE CCFL ANGEL EYES FITTING GUIDE COURTESY OF BEN @ CHROMELINE DESIGN Page 1 of 8 : Thank you for purchasing Eclipse Lights for your BMW E36. Please read through these instructions carefully before
More informationColour-CHANGE Lights THX72-CCP Thru-Hull and THX72-CCP-FF Flush Fit Installation and Operation Guide
Colour-CHANGE Lights THX72-CCP Thru-Hull and THX72-CCP-FF Flush Fit Installation and Operation Guide THX72-CCP THX72-CCP-FF Congratulations! You have purchased a LUMISHORE advanced technology LED underwater
More informationAt125 Kopa Anti tamper ip65 reflector
AT125 At125 Kopa Anti tamper ip65 reflector MULTI WATT LED (7-18W) General 7/10/13/18W options IP65 rated from below CRI >80 (3000k, 4000k) 3 SDCM colour consistency Rated life 50,000 hours Reflector beam
More informationSPORTSTER SADDLEBAG KIT. i i02212
General These saddlebags are designed to fit 99 and later Sportster Model Motorcycles, except XL00 Sport models with gas reservoir shock absorbers and 88R models. See the Service Parts pages for a list
More information96W Colored LED Light Bar - Completely Submersible 'L X 200'W Spot VDC Lumens
96W Colored LED Light Bar - Completely Submersible - 1100'L X 200'W Spot - 9-42VDC - 5760 Lumens Part #: LEDXUL-32C Page: 1 Larson Electronics LLC Buy American Compliant The LEDXUL-32C from Larson Electronics
More informationHPP1 MK5 Owner s Manual
J Wolmarans Page 1 2017/03/07 Page 1 of 10 TABLE OF CONTENTS Page 1 Introduction...2 2 Models...2 3 Safety warnings...3 4 Features...3 5 Contents...3 6 Installation...3 6.1 Mounting the unit:...3 6.2 Connecting
More information20W HID Explosion Proof Search Light - C1D1 & C2D VAC Stepped Down to 12V DC - 50' SOOW
20W HID Explosion Proof Search Light - C1D1 & C2D1-120-277VAC Stepped Down to 12V DC - 50' SOOW Part #: EPL-20W-HID-X12V-50-HR Buy American Compliant The EPL-20W-HID-X12V-50-HR from Larson Electronics
More information(K),(M)430TB/G Up to 36 kv
IS90722-ENG - 430TB/G-45 25 June 2009 - Revision 8A - Supersedes edition of 25 November 2008 Page 1 of 10 CAUTION : Read instructions thoroughly and completely prior to beginning installation. Installation
More informationINSTALLATION AND SERVICE INSTRUCTIONS FOR 2000 SERIES FLAMEPROOF XENON AND FLUORESCENT BEACONS
INSTALLATION AND SERVICE INSTRUCTIONS FOR 2000 SERIES FLAMEPROOF XENON AND FLUORESCENT BEACONS Address all communications and shipments to: FEDERAL SIGNAL CORPORATION Industrial Systems Group 2645 Federal
More information31 Watt Low Voltage LED Fixture for Industrial Lighting - Adjustable Trunnion U-Bracket Mount
31 Watt Low Voltage LED Fixture for Industrial Lighting - Adjustable Trunnion U-Bracket Mount Part #: GAU-31L-LV Page: 1 Buy American Compliant The GAU-31L-LV is a low voltage industrial lighting solution
More informationKLIK LEDpod 40 Patented
KLIK LEDpod 40 Patented Description Discrete, seamless point source LED fixture for use in all code-compliant handrail, especially curving ramps and helical stairs as well as long runs on bridges and pedestrian
More informationAquaLumin III - Nicheless Light Installation Guide IMPORTANT SAFETY INSTRUCTIONS READ AND FOLLOW ALL INSTRUCTIONS SAVE THESE INSTRUCTIONS
16 1 AquaLumin III - Nicheless Light Installation Guide IMPORTANT SAFETY INSTRUCTIONS READ AND FOLLOW ALL INSTRUCTIONS SAVE THESE INSTRUCTIONS Section Contents 1. Installing a mounting bracket and light
More informationHE-PSU(4.0) Power Supply & Battery Charger Installation, Commissioning & Operating Manual
HE-PSU(4.0) Power Supply & Battery Charger Installation, Commissioning & Operating Manual Page 1 of 10 CONTENTS 1. GENERAL...2 2. POWER REQUIREMENTS...2 2.1 HE-PSU(4.0) Input/Output Electrical Ratings...2
More information7118 Series Halogen Deck Floodlights
7118 Series Halogen 7118 Series Fibre reinforced housing and Free Form reflector for close range homogeneous illumination. Off White Housing Structured Lens - Hella 'Free Form' reflector technology - and
More informationJUNCTION BOX FOR CATHODIC PROTECTION
JUNCTION BOX FOR CATHODIC PROTECTION Yuxi manufacture a serious type of junction box required for a cathodic protection system. Our junction box is designed to use reliably for onshore and marine environments
More informationCalculite LED 7" Downlight
½" mm ⅛" mm Total height of Light engine + Reflector ⅛" mm ¼" mm Project: Downlighting Location: Cat.No: Type: Calculite LED " features an LED array of high brightness white light LEDs. The new LED boards
More informationKLIK LEDpod 50 Patented
KLIK LEDpod 50 Patented Description Discrete, seamless point source LED fixture for use in all code-compliant handrail, especially curving ramps and helical stairs as well as long runs on bridges and pedestrian
More informationBluefin Led Underwater lights.
Bluefin Led Underwater lights. Domestic DL6 Installation manual. Thank you for choosing Bluefin LED underwater lights, our products have been designed and tested rigorously to ensure the optimum performance
More informationExplosion Proof Light - Class 1 Division 2 Light - 5 hour Run Time Li-ion Battery - MADE IN THE USA
Explosion Proof Light - Class 1 Division 2 Light - 5 hour Run Time Li-ion Battery - MADE IN THE USA Part #: RUL-9-FR Page: 1 Larson Electronics LLC Made in The USA The RUL-9-FR Hazardous Area Portable
More informationICOMIA Global Conformity Guideline for ISO/ABYC Standards and Canadian TP 1332 requirements. Guideline Number 3 Electrical
ICOMIA Global Conformity Guideline for ISO/ABYC Standards and Canadian TP 1332 requirements 1. PURPOSE sponsored by ABYC, BMF, ICOMIA, IMCI, and NMMA Author: Wieger de Wit Guideline Number 3 Electrical
More informationWPP25 250W MP Wal-Pak Borosilicate Glass Hinged/Removabl
3804 South Street 75964-7263, TX Nacogdoches Phone: 936-569-7941 Fax: 936-560-4685 WPP25 250W MP Wal-Pak Borosilicate Glass Hinged/Removabl Catalog Number Manufacturer Description Weight per unit Product
More information100 Watt LED Light lumens Volts DC - Adjustable Surface Mount - Flood LED Light
100 Watt LED Light - 9000 lumens - 9-48 Volts DC - Adjustable Surface Mount - Flood LED Light Part #: LED10W-10R-F Buy American Compliant The Larson Electronics LED10W-10R-F LED Light Bar offers high light
More informationOptions. Pole and Arm. Suitable for wet locations
Catalog number: / / / Mtg. Fixture Electrical Module Finish See page 2 See page 3 Options Pole and Arm Select pole from Kim Arms and Poles Selection Guide. If pole is provided by others indicate O.D. for
More information01 Research & Mechanical Production. Lighting Value
S E A L E D Sealed Series TOWARDS A NEW HORIZON Dear Customer, When LED (Light Emitting Diode) technology was born a big change occured in the lighting world. Many innovations and developments of this
More informationKLIK LEDpod 40 Patented
KLIK LEDpod 40 Patented Description Discrete, seamless point source LED fixture for use in all code-compliant handrail, especially curving ramps and helical stairs as well as long runs on bridges and pedestrian
More informationOutdoor Installation Using an Electronic LED Power Supply (TE-60L-12)
0 Edge Lighting. All Rights Reserved. 78 W. Fullerton Ave Chicago, IL 606 Tel: 77-770-9 Fax: 77-9-6 www.edgelighting.com info@edgelighting.com Installation Instructions for Port Round & Square LED PORT-RD-ST-SA
More information220/230/240V Watt High Pressure Sodium - Hazardous Location Lighting - C1D2 - Pole Mount
220/230/240V Watt High Pressure Sodium - Hazardous Location Lighting - C1D2 - Pole Mount Part #: HAL-PRM-250W-HPS-220V-PT Page: 1 Made in the USA The efficient HAL-PRM-250W-HPS-220V-PT high pressure sodium
More informationFluorescent Lighting FE Series: Nonmetallic Fluorescent Lighting Fixtures, Standard and Emergency Battery Back-Up Increased Safety
Fluorescent Lighting FE Series: Nonmetallic Fluorescent Lighting Fixtures, Standard and Emergency Battery Back-Up Increased Safety Zone & & II GD IP66/67 IK0 Applications: Can be installed in hazardous
More informationCompact Sine Inverter
Compact Sine Inverter Instructions for installation & use Applies to the following models: Output power: 700watt, 1000 watt, 1500watt, 2000 watt & 3000 watts Output voltage: and output, 50Hz & 60Hz Output
More informationNEW NEW. 650m .00. m 1LUX. 600m FEATURES: High Colour Rendering. Index (CRI) at 5000 K WITH TWO LAMPS* Signature L.E.
E N H A N C E D O P T I C L. E. D D R I V I N G L I G H T S HIGH POWERED L.E.D DRIVING LIGHT 820.00 KIT Ultima 225 L.E.D Combination Driving Light Kit, 225mm dia. P/No. 71705 480.00 PER LAMP FEATURES:
More informationAFL10-LED-KIT Architectural FloodLight HID to LED Upgrade Kit kl_afl10_ledkit_spec.pdf
JOB NOTES TYPE APPROVALS FEATURES Three beam patterns Wide, Vertical and Narrow Flood generate high efficiencies and outstanding uniformity of illumination. 350 or 500mA current 3000K, 4000K or 5000K color
More informationOceanLED This installation manual covers the following products:
OceanLED Marine Product Support OceanLED This installation manual covers the following products: PRO SERIES HD Gen2 INSTALLATION MANUAL PRO SERIES HD Gen2 Thru-Hull Thru-Hull Thru-Hull 2010TH HD Gen2 3010TH
More informationDeSoto NEMA 4X EMERGENCY LIGHTING UNIT. U.S. Versions: 6V- DM90X618 / DM90X654 12V- DM90X1254 / DM90X12100 INSTALLATION INSTRUCTIONS
DeSoto U.S. Versions: 6V- DM90X618 / DM90X654 12V- DM90X1254 / DM90X12100 NEMA 4X EMERGENCY LIGHTING UNIT INSTALLATION INSTRUCTIONS U.S. Patent No.s 6,135,624; 6,193,395; 6,502,044 B1; D505,222; IMPORTANT
More informationOEM Emergency Portfolio. Product Guide. Emergency components for LED, fluorescent and auxiliary purpose
OEM Emergency Portfolio Product Guide Emergency components for LED, fluorescent and auxiliary purpose Contents Introduction to this guide 3 LED Modules 4 PHL-EL3 PHL-EL3-80 PHL-EL3-D PHL-EL3-D80 PHL-EL3-4
More informationFloodlight Series 6121
www.stahl.de Floodlight > For use in gas group IIC (-20 C... +C) gas group IIB + H 2 (-C... +C) > Material Enclosure in seawater resistant cast aluminium Mounting components in stainless steel > Lamp options
More informationEX Series User Manual
MODELS: EX90L T4 IIB 720 DS, EX90L T4 IIB 1440 SS, EX90L T4 IIC 720 SS EXIN LIGHT EX & INDUSTRIAL LIGHTING EX Series EX90L T4 IIB 720 DS, EX90L T4 IIB 1440 SS, EX90L T4 IIC 720 SS Contents 0. Introduction
More informationLight Fitting for Fluorescent Lamps Series ECOLUX 6600
> 1- or 2-lamp version: 18 W 36 W 58 W > Enclosure in polyester resin, glass fibre reinforced and cover in polycarbonate, impact-resistant > Quick fasteners www.stahl.de 10032E00 The light fittings series
More informationSTOP BEFORE YOU BEGIN READ THESE INSTRUCTIONS COMPLETELY AND CAREFULLY
STOP BEFORE YOU BEGIN READ THESE INSTRUCTIONS COMPLETELY AND CAREFULLY WARNING Risk of fire or electrical shock. LED retrofit installations require knowledge of luminaire electrical systems. If not qualified,
More informationIMPORTANT SAFETY INSTRUCTIONS READ AND FOLLOW ALL INSTRUCTIONS SAVE THESE INSTRUCTIONS
1 AQUALUMIN III NICHELESS POOL LIGHT INSTALLATION GUIDE IMPORTANT SAFETY INSTRUCTIONS READ AND FOLLOW ALL INSTRUCTIONS SAVE THESE INSTRUCTIONS Section Contents 1. Installing a mounting bracket and light
More information1000W and 2000W versions
503 FLOODLIGHT 126 600W HPS 1000W and 2000W versions The 503 is a high powered floodlight with a wide ambient temperature range. The high upper ambient and corrosion resistant aluminium constriction, make
More informationHID Golight Stryker - Perko Post Mount Foot Beam - Wireless Remote Control - White
HID Golight Stryker - Perko Post Mount - 5000 Foot Beam - Wireless Remote Control - White Part #: GL-9100H-S The GL-9100H-S Golight HID Golight Boat Light on Stanchion Mount from Larson Electronics produces
More informationTHE HIGH STRIP FIXTURE SERIES PERFORMANCE KEY FEATURES INCLUDE:
THE HIGH PERFORMANCE LED Fixture Series (surfacemount or hung) for Passageway, Stairwells, General, Direct and Indirect Illumination KEY FEATURES INCLUDE: Advanced Thermal Management Industry Leading Deep
More informationOSLON SSL LED 480mm PowerLinear White
OSLON SSL 80 15 LED 480mm PowerLinear ILS-ON15-xxxx-0480-SC211-xx Series Product Overview At the heart of each PowerLinear 480mm are 15 OSRAM Opto Semiconductors OSLON SSL 80 ThinGan (UX:3) LED. These
More informationWELLGLASS EV.. Series - H.I.D. well glass lighting fixture. Aluminium with low content of copper. O-ring made of Nitrile Rubber (NBR)
WELLGLASS EV.. Series - H.I.D. well glass lighting fixture EV.. series well glass lighting fixtures are suitable for hazardous areas of industrial plants for lighting of indoor and outdoor structures,
More informationStanley 3J 1 PowerStar Whites
Stanley 3J 1 PowerStar s ILS-SJ01-xx95-SC201-xx Series Product Overview At the heart of each PowerStar is a Stanley Electric 3J Series LED giving outstanding luminance with CRIs in excess of 95. All Stanley
More informationATX FE Series Nonmetallic Fluorescent Luminaires Standard and Emergency Battery Back-Up. Increased Safety
Applications Can be installed in hazardous areas designated as Zone 1 and 2 21 and 22. For use in locations where a high degree of corrosion resistance is required. For indoor/outdoor use where protection
More information1000 Watt Metal Halide Flood Light - 110,000 Lumens - Slipfitter Mount - 120~277 Volts AC
1000 Watt Metal Halide Flood Light - 110,000 Lumens - Slipfitter Mount - 120~277 Volts AC Part #: MHFL-1000W Made in the USA The powerful and efficient MHFL-1000W metal halide light fixture from Larson
More informationATD-5925 RECHARGEABLE 12 VOLT 18 AMP/HOUR JUMP START WITH BUILT-IN 260 PSI AIR COMPRESSOR OWNERS MANUAL
ATD-5925 RECHARGEABLE 12 VOLT 18 AMP/HOUR JUMP START WITH BUILT-IN 260 PSI AIR COMPRESSOR OWNERS MANUAL 1000 PEAK AMPS/400 CRANKING AMPS OF STARTING POWER. STARTS CARS, TRUCKS, RV s AND BOATS WITHOUT THE
More information7 Lighting Technology
7 Lighting Technology Light Fittings for Fluorescent Lamps Series EXLUX 6400 (Zones 2, 21 & 22) As pendant or pole-mounting fittings With electronic ballast For two-pin fluorescent lamps 1 or 2 lamp versions:
More information