MF19 3/4 /19mm Chromed Rod. Now offered in a Bottom Threaded Mount (BTM) or Bottom Flange Mount (BFM), as well as drop in and standard top mount.

Transcription

1 N-FORCER CER Nitrogen Die Springs MF25 1 /25mm MF19 3/4 /19mm Chromed Rod CAN BE REBUILT Rod Wiper New Mounts Seal Bearing Made in the U.S.A. Our Mini Cylinder (1 /25mm) MF25 & MF19 (3/4 /19mm) Series are available in all standard strokes. Also available in (1-1/4 / 32mm) stroke with approximate height of 4 die spring. Now offered in a Bottom Threaded Mount (BTM) or Bottom Flange Mount (BFM), as well as drop in and standard top mount. Bottom Threaded Mount and Bottom Flange can be hosed, the Threaded Mount can be threaded in a block for use as manifold by adding an o-ring. Special Heights and Strokes are Available. Rebuild kits are available. Die, Mold & Automation Components, Inc N-r Henn St Dearborn, MI Ph: Fax: customerservice@n-forcer.com

2 Mini-r All MF-19 s are Adjustable (psi) Variable on Contact (lb.-f) (bar) (0) P=Fe. 078 F=P X.078 P= Fe0. P=FX0. Order Number S Maximum Stroke L L min MF MF MF MF MF MF MF Color Coding Yellow - YW Order by Color Code Initial Final Psi Bar MF19-0 MF MF MF Red - RD MF Blue - BL Green - GR Black - BK See Chart Above Ordering Example: MF (Color) MF is the part number 2. (Color) is the required charging pressure. Mounts Are Ordered Seperately (see next Page) To Increase : Connect nitrogen to charging port at botton of gas spring and charge to correct pressure. To Decrease : Insert 3mm Hex Key into tapped hole in bottom of gas spring. Turn clockwise (maximum of 3 turns), making sure opening is away from your face and body. After all pressure is exhausted, turn the screw in the bottom of the gas spring counterclockwise until tight. You can now recharge the gas spring to a lower pressure. 2

3 Mini-r Optional Mount Mount Part Number is BNF19 The cylinder can be mounted from 3 different locations, but the bottom should be supported when either of the two top locations are utilized. 3

4 Mini-r MF19 THREADED All MF-19 s are Adjustable (psi) Variable on Contact (lb.-f) (bar) (0) P=F. 078 F=P X.078 P= F 0. P=FX0. Order Number S Maximum Stroke L L min MF MF MF MF MF MF MF Order by Color Code MF Color Coding Yellow - YW Initial Final Psi Bar MF MF MF Red - RD MF Blue - BL Green - GR Black - BK See Chart Above Ordering Example: MF (TM or TE)-(Color) 1. MF is the part number 2. TM is for Metric - TE is for English Thread 3. (Color) is the required charging pressure. Mounts Are Ordered Seperately (see next Page) To Increase : Connect nitrogen to charging port at botton of gas spring and charge to correct pressure. To Decrease : Insert 3mm Hex Key into tapped hole in bottom of gas spring. Turn clockwise (maximum of 3 turns), making sure opening is away from your face and body. After all pressure is exhausted, turn the screw in the bottom of the gas spring counterclockwise until tight. You can now recharge the gas spring to a lower pressure. 4

5 MF19 Threaded Nuts Part # 1-8 Nut Part # M24 x 1.5 Nut N-FORCER MF19 Theaded Tool Installer Part # MF19-Tool 5

6 Mini-r All MF-25 s are Adjustable (psi) Variable on Contact (lb.-f) (bar) (0) P=Fe. 176 F=PX.1176 P= Fe1.13 P=FX 1.13 Color Coding Yellow - YW Red - RD Blue - BL Green - GR Black - BK Order by Color Code Initial Final See Chart Above Ordering Example: MF (Color) Psi Bar MF is the part number 2. (Color) is the required charging pressure. Mounts Are Ordered Seperately (see next Page) ** Order Number MF MF MF MF MF MF MF MF MF25-0 MF MF MF25- MF MF S Maximum Stroke L L min To Increase : Connect nitrogen to charging port at botton of gas spring and charge to correct pressure. To Decrease : Insert 3mm Hex Key into tapped hole in bottom of gas spring. Turn clockwise (maximum of 3 turns), making sure opening is away from your face. After all pressure is exhausted, turn the screw in the bottom of the gas spring counterclockwise until tight. You can now recharge the gas spring to a lower pressure. **Limited speed and stroke life. 6

7 Mini-r Optional Mount Mount Part Number is BNF25 The bottom shoud be supported at all times. 012/ /.84 1/0.04 9/ /1.34 0/ / / /.26 7