Load Centers & Circuit Breakers

Transcription

1 Load Centers & Circuit Breakers SPEEDFAX TM 207 Section PL Series Load Center Generator Ready Load Center C o n t e n t s Load Centers ing System -2 Siemens PL and ES Series Load Centers Introduction -3 WireGuide Load Centers and Breakers -3 PL Series Load Centers Features and Product Offering -4-5 PL Series Single Phase Main Lug & Main Breaker Load Centers -6 PL Series Single Phase Special Load Centers -7 PL Series Three Phase Main Lug & Main Breaker Load Centers -8 PL Series Three Phase Unassembled Load Centers -9 ES Series Load Centers Features and Product Offering -0 - ES Series Single Phase Main Lug & Main Breaker Load Centers -2 ES Series Single Phase Special Load Centers -4 ES Series Three Phase Main Lug & Main Breaker Load Centers -5 EQ Load Centers, Generator Ready Load Centers -7 Riser Panel Load Centers -8 EQ Load Centers, Small Circuit and Circuit Breaker Enclosures Load Centers OEM Interiors and Accessories Standby Power Systems Knockout Diagrams Load Center Cross Reference Circuit Breakers Arc-Fault and Ground-Fault Breakers -34 Intelli-Arc Diagnostic Tool -35 Type QP, " Breakers -36 Duplex, Triplex and Quadplex Plug-In Breakers -37 Special Application Breakers -38 Type QD, 3/4" Breakers -39 Main and Branch Circuit Breakers -40 Circuit Breaker Dimension Drawings and Lug Data Circuit Breaker Accessories Surge Protection Products AC Disconnects, -Phase, NEMA 3R Rated -48 WireGuide Load Center Scan to connect online to the most up-todate version of this Section of SPEEDFAX. Siemens Industry, Inc. SPEEDFAX 207 Product Catalog -

2 Load Centers ing System ing System Type Enclosure or Component E = Indoor Type 2-0 and circuits G = Indoor Type 2-42 circuits W = Outdoor Type 3R I or PI = Interior R = Riser P = PL Series Indoor Type 2-70 circuits S = ES Series Indoor Type 2-70 circuits PW = PL Series Outdoor Type 3R 2-70 circuits SW = ES Series Outdoor Type 3R 2-70 circuits Maximum number of " breakers Maximum number of circuits Type of Main ML or L = Main Lug MB or B = Main Breaker System = -Phase, 3-Wire 3 = 3-Phase, 3-Wire or 3-Phase, 4-Wire Main ere Ex:00 = 00 s Interior Blank A = Standard = Wireguide Trim/ Others Blank = Combination S = Surface F = Flush T = Feed-Thru Lugs G or GB = Ground Bar Factory Installed Type of Bus Bar Blank C or CU P Trim Color Blank = Grey W = White = Aluminum = Copper = Aluminum Bus, Value Pack P 2 24 B 00 A S CU W Products Shown In Sections of this Speedfax Meet or Exceed the Following Standards. n UL50 Electric Cabinets and Boxes n UL67 Electric Panelboards n UL486 Wire Connectors n UL489 Molded-Case Circuit Breakers n UL869 Service Equipment n UL943 Ground Fault interrupters (Class A Personnel Protection) n Federal Specification W-P-5b Panel Power Distribution n Federal Specification W-C-375B Circuit Breakers n NEC n NEMA 250 Underwriters Laboratories, Inc. Reference File Numbers: n Series Connected Circuit Breaker Information is recognized by UL under file #E0848(N) n Load Centers Listed by UL under file #E0703 n Load Centers UL recognized components found under file #E0703, Volume 6 and 7. (Also referenced under the recognized components directory section QEUY2) n EQ Circuit Breakers are Listed by UL under file #E Siemens Industry, Inc. SPEEDFAX 207 Product Catalog

3 Load Centers Revised on 0/30/7 Siemens PL and ES Series Load Centers Overview PL Series: n Convertible n Invertible a n Insta-wire neutrals & grounds n Ground bars included n Copper busbars n Dual neutrals on all configurations n Carton-in-carton packaging n Lifetime warranty ES Series: n Invertible a n Insta-wire neutrals & grounds n Aluminum busbars n Single sided neutral on 24 circuits and below n Single piece carton packaging n 0 year warranty PL Series -phase PL Series 3-phase ES Series -phase ES Series 3-phase NEW WireGuide Load Centers and Breakers WireGuide load centers accept new AFCIs with shortened neutral wires that slide directly into the neutral bar. Features n Over 4 inches of breaker wire bending space n SKUs each available in both grey and white a n Pre-trimmed and ready to install neutral wires have an "Oops Loop" if extra wire is needed n Full length neutral bars n Decreased installation time n WireGuide breakers available by adding "WG" suffix to existing catalog numbers. See page -34 for more details. WireGuide Load Centers Combination Type AFCI WireGuide Breaker a Applies only to NEMA ES and PL Load Centers Siemens Industry, Inc. SPEEDFAX 207 Product Catalog -3

4 PL Series Load Centers Revised on 03/02/7 Features All devices are provided with 2 factory installed ground bars. Invertible for bottom feed application. a All devices convertible from main lug to main breaker and vice versa. Mounting tabs on the trim hold it in place on the load center, freeing up both hands to drive the trim screws. Combination head screw on the neutrals, ground, trim, upper pan, and bond screw provide installation flexibility. A rigid, sturdy base pan provides the ruggedness required for the most harsh applications. The prepositioned bond screw eliminates bond strap/ screw assemblies, and reduces the risk of losing components in the field. The patented INSTA-WIRE neutral/ground system allows for faster installation because screws are backed out, ready for wire insertion. The visible neutral and grounds system aids in the insertion of conductors. Copper Bus The outdoor enclosure has a slide hinge door for the easiest installation and can be removed by backing out only one screw. PL Series Load Centers ship with trims packaged separately. a Applies only to NEMA ES and PL Load Centers -4 Siemens Industry, Inc. SPEEDFAX 207 Product Catalog

5 PL Series Load Centers Product Offering The PL Series Load Center product line provides a wide array of variation to meet any application need. The following offering is available in the PL Series product line: n 2-70 / n Indoor and Outdoor enclosures n 00 to 225 n Main Lug and Main Breakers n Un-assembled offering in 3-phase PL Series -phase Main Lug PL Series 3-phase Main Breaker Un-assembled 3-phase Product Category RESI Siemens Industry, Inc. SPEEDFAX 207 Product Catalog -5

6 PL Series -Phase Main Lug & Main Breaker Load Centers -phase, 3-wire SN, 20/240 Volts AC Revised on /29/7 Main Breaker/Convertible Load Centers Copper Bus 2-70 / eres 60/75 C Rated 22,000A IR Indoor Enclosure NEMA Type PL Catalog Number PL with WireGuide Interior Catalog Number NEMA - (inches) c Outdoor Enclosure NEMA Type 3R NEMA 3R - (inches) d 2 24 P224B00CU 8 24 PW224B00CU P624B00CU 2 24 PW624B00CU P2020B00CU 20 PW2020B00CU P2040B00ACU P2024B00CU P2424B00CU 48 P2448B00ACU P3030B00CU 60 P3060B00ACU PW3040B00CU P3030B25CU 60 P3060B25ACU PW3040B25CU P2030B50CU 40 P2040B50ACU PW2030B50CU P3030B50CU 60 P3060B200ACU PW3040B50CU P2040B200CU 40 P2040B200ACU PW2040B200CU P3040B200CU 60 P3060B200ACU PW3040B200CU 35 P3040B P3060B200A P4040B200CU 80 P4080B200ACU PW4040B200CU 38 P4040B P4080B200A P5470B200CU 80 P5480B200ACU P4260B225CU 80 P4280B225ACU PW4260B225CU P5470B225CU 80 P5480B225ACU 44 Single phase factory installed 22kA IR main circuit breaker offers 22/0kA IR series combination rating when using 0kA type QP, QT, QPF, QE, QN, and QAF2/QAF2C branch breakers. Main Lug/Convertible Load Centers f Copper Bus 2-70 / eres 60/75 Rated 00,000A IR Indoor Enclosure - NEMA Type PL Catalog Number PL with WireGuide Interior Catalog Number NEMA - (inches) c Outdoor Enclosure - NEMA Type 3R 2 2 P22L25CU e 8 2 PW22L25CU e 2 24 P224L25CU e 8 24 PW224L25CU e P624L25CU 2 24 PW624L25CU P2020L25CU P2040L25ACU 24 P2024L25CU P2440L25CU 48 P2448L25ACU P3040L25CU 60 P3060L25ACU PW3040L25CU P4040L25CU 80 P4080L25ACU P2030L50CU 40 P2040L50ACU PW2030L50CU P224L200CU PW224L200CU e P2040L200CU 40 P2040L200ACU PW2040L200CU P2440L200CU 48 P2448L200ACU P3030L200CU P3040L200CU 60 P3060L200ACU PW3040L200CU P3054L200CU 54 PW3054L200CU P3040L P3060L200A P4040L200CU 80 P4080L200ACU PW4040L200CU P4040L P4080L200A PW224L225CU P4260L225CU 80 P4280L225ACU PW4260L225CU P5470L225CU 80 P5480L225ACU 44 NEMA 3R - (inches) d Suitable for use as service equipment. b May be installed on higher rated systems when protected by a circuit breaker with a higher AIR rating. c Indoor enclosures are 4 /4" wide by 3 7/8" deep. d Outdoor enclosures are 4 /2" wide by 4 /4" deep. e Suitable for use as service entrance equipment when not more than six main disconnecting means are provided. See article of the NEC. f 25A load centers will accept MBK00A and MBK25A. 50A load centers will accept MBK50A. 200A load centers will accept MBK200A and MBK50A. 225A load centers will accept MBK225A, MBK200A, MBK50A. g Copper bus load centers are recommended for those applications where the environment may be severe (i.e. far and coastal areas). h Includes all PL Series features with aluminum bussing. i Available (made to order) in white by adding "W" to the end of the part number. -6 Siemens Industry, Inc. SPEEDFAX 207 Product Catalog Product Category RESI

7 PL Series -Phase Special Application Load Centers -phase, 3-wire SN, 20/240 Volts AC Split Ground Series Main Lug Convertible Load Centers Copper Bus 2-60 / eres 60/75 Rated, 00,000A IR Branch Indoor Enclosure NEMA Type P224L25CUSG P624L25CUSG P2030L25CUSG P2430L25CUSG P2030L50CUSG P3040L200CUSG P3040L200SG P4040L200CUSG P4040L200SG P4260L225CUSG 39 (inches) Split Ground Series Main Breaker Convertible Load Centers Copper Bus 40 / 200 eres 60/75 Rated, 22,000A IR Branch Indoor Enclosure NEMA Type First Surge PL Load Centers Copper Bus /75 Rated, 22,000A IR P4040B200CUSG 36 Surge Protection P3054B200S40 40kA 36 (inches) (inches) Split Ground Load Centers have factory installed 00% neutral with factory bonded 75% ground. No neutral tie strap P4060B200S40 40kA 42 Outdoor Trailer Panels Copper Bus 6 / 200 eres 60/75 Rated, 22,000A IR Main Breaker MBK50A or MBK200A PW086L200TC PW086B200TC MBK200A Field Installed 23 Factory Installed (inches) 23 Includes all PL Series features with aluminum bussing. Indoor enclosures are 4 /4" wide by 3 7/8" deep. May be installed on higher rated systems when protected by a circuit breaker with a higher AIR rating. Outdoor enclosures are 4 /2" wide by 4 /4" deep. Main lug panel rated 00,000A IR. Load centers with white trim have increased lead time of 3-4 weeks. Sold in pallet quantities only. Load centers with CUW suffix indicates copper bus with white trim. Load centers with W suffix only indicates aluminum bus with white trim. Product Category RESI Siemens Industry, Inc. SPEEDFAX 207 Product Catalog -7

8 PL Series 3-Phase Main Lug & Main Breaker Load Centers 3-phase, 3-wire, 240 Volt AC or 3-phase, 4-wire, 20/240 or 20/208 Volts AC Main Breaker/Convertible Load Centers Copper Bus / eres 60/75 C Rated 22,000A IR Branch Indoor Enclosure NEMA Type Outdoor Enclosure NEMA Type 3R (inches) P224B300CU P3042B300CU P3030B325CU P2442B350CU P4242B350CU P3054B3200CU 39 PW3054B3200CU P4260B3200CU 42 PW4260B3200CU P4260B3225CU P4260B3225TCU P5470B3225CU 49 (inches) Main Lug/Convertible Load Centers Copper Bus 2-70 / eres 60/75 Rated 00,000A IR Branch Indoor Enclosure NEMA Type Outdoor Enclosure NEMA Type 3R (inches) P224L325CU 2 PW224L325CU P2442L3200CU 36 PW2442L3200CU P3054L3200CU 39 PW3054L3200CU P4260L3225CU 42 PW4260L3225CU P5470L3225CU 49 (inches) May be installed on higher rated systems when protected by a circuit breaker with a higher AIR rating. Back fed main breaker. Indoor enclosures are 4 /4" wide by 3 7/8" deep. Outdoor enclosures are 4 /2" wide by 4 /4" deep. Suitable for use as service entrance equipment when not more than six main disconnecting means are provided. See article of the NEC. Includes factory installed feed through lugs and is also non-convertible. Non-convertible to main breaker. All load centers are provided with tin plated copper bus bars. Rated 00,000A IR in series with breakers listed on wiring diagram. All load centers are provided with tin-plated copper bus bars. Available (made to order) in white by adding "W" to the end of the part number -8 Siemens Industry, Inc. SPEEDFAX 207 Product Catalog Product Category RESI

9 PL Series 3-Phase Unassembled Load Centers 3-phase, 3-wire, 240 Volt AC or 3-phase, 4-wire, 20/240 or 20/208 Volts AC Main Breaker Convertible Unassembled Load Centers Copper Bus / eres 60/75 C Rated 22,000A IR Interiors Enclosure Trim Kit Interior (inches) Enclosure No. Breaker Trim PI3042B300CU 30 3PE30 30 PT3042B PI2442B350CU 36 3PE36 24 PT2442X PI3054B3200CU 39 3PE39 30 PT3054X PI4260B3200CU 42 3PE42 42 PT4260X PI5470B3225CU 49 3PE49 54 PT5470X3225 Main Lug Convertible Unassembled Load Centers Copper Bus 2-70 / eres 60/75 Rated 00,000A IR Interiors Enclosure Trim Kit Interior (inches) Enclosure No. Breaker Trim PI224L325CU 2 3PE2 2 PT224L PI2442L3200CU 36 3PE36 24 PT2442X PI3054L3200CU 39 3PE39 30 PT3054X PI4260L3225CU 42 3PE42 42 PT4260X PI5470L3225CU 49 3PE49 54 PT5470X3225 May be installed on higher rated systems when protected by a circuit breaker with a higher AIR rating. Back fed main breaker. Indoor enclosures are 4 /4" wide by 3 7/8" deep. Trim catalog numbers with a B indicate for use with main breaker and is not convertible. L indicates for use with main lug and is not convertible. X indicates can be used with convertible interior. All load center interiors are provided with tin plated copper bus bars. Rated 00,000A IR in series with breakers listed on wiring diagram. Product Category RESI Siemens Industry, Inc. SPEEDFAX 207 Product Catalog -9

10 ES Series Load Centers Revised on 03/02/7 Features Combination head screw on the neutrals, ground, trim, upper pan, and bond screw provide installation flexibility. Invertible for bottom feed application. a Ground bar field installed (select skus with G suffix will have ground bar factory installed). Mounting tabs on the trim hold it in place on the load center, freeing up both hands to drive the trim screws. The prepositioned bond screw eliminates bond strap/ screw assemblies, and reduces the risk of losing components in the field. Single side inboard neutral on 24 circuits and below; dual on 30 circuits and above. A rigid, sturdy base pan provides the ruggedness required for the most harsh applications. The patented INSTA-WIRE neutral/ground system allows for faster installation because screws are backed out, ready for wire insertion. The visible neutral and grounds system aids in the insertion of conductors. Aluminum bus. ES Series Load Centers ship in single piece carton. The outdoor enclosure has a slide hinge door for the easiest installation and can be removed by backing out only one screw. a Applies only to NEMA ES and PL Load Centers -0 Siemens Industry, Inc. SPEEDFAX 207 Product Catalog

11 ES Series Load Centers Product Offering The ES Series Load Center product line provides a wide array of variation to meet any application need. The following offering is available in the ES Series product line: n 2-70 / n Indoor and Outdoor enclosures n 00 to 225 n Main Lug and Main Breakers n Value packs a mix of branch breakers provided with the load center. ES Series -phase Main Lug 25A, 2-24 circuits ES Series - phase Main Breaker A, circuits ES Series 3-phase Main Breaker Product Category RESI Siemens Industry, Inc. SPEEDFAX 207 Product Catalog -

12 ES Series -Phase Main Lug & Main Breaker Load Centers -phase, 3-wire SN, 20/240 Volts AC Revised on /29/7 Main Breaker Aluminum Bus 2-70 / eres 60/75 C Rated 22,000A IR Indoor Enclosure NEMA Type Outdoor Enclosure NEMA Type 3R ES Catalog Number ES with WireGuide Interior Catalog Number h NEMA - (inches) c NEMA 3R - (inches) d 0 20 S020B S224B SW224B S624B00 h 2 24 SW624B S2020B00 20 SW2020B S2040B00A S2024B S3030B00 h 60 S3060B00A SW224B S624B SW2024B S2424B25 h 48 S2448B25A SW2424B S3030B25 h 60 S3060B25A S3040B25 40 SW3040B S630B S2030B50 40 S2040B200A S2430B50 48 S2448B200A S3030B50 h 60 S3060B50A S3040B50 40 SW3040B SW4040B S632B S2040B S2040B200A SW2040B S2440B S2448B200A S3040B200 h 60 S3060B200A SW3040B S4040B200 h 80 S4080B200A SW4040B S4260B S4280B200A S5470B S5480B200A S4260B S4280B225A SW4260B S5470B S5480B225A 44 Main Lug Aluminum Bus 2-70 / eres 60/75 Rated 00,000A IR 25 Indoor Enclosure - NEMA Type Outdoor Enclosure - NEMA Type 3R ES Catalog Number(6) ES with WireGuide Interior Catalog Number fh NEMA - (inches) c NEMA 3R - (inches) d 2 2 S22L25 e 8 2 SW22L25 e 2 24 S224L25 e 8 24 SW224L25 e S624L SW624L S2020L25 h S2020L25G h 40 S2040L25AG 2 24 S2024L25 24 S2024L25G 24 S2424L25 h 24 SW2424L S2424L25G h 48 S2448L25AG S2440L25 h 40 S2440L25G S3040L25 h 40 SW3040L25 29 S3060L25AG S3040L25G h S4040L25 80 S4080L25AG S2030L50 h 40 S2040L50AG SW2030L S224L200 e 2 24 SW224L200 e S2040L S2040L200AG SW2040L S2440L200 h 48 S2448L200AG S3030L S3040L S3060L200AG SW3040L S3054L SW3054L S3040L200L50 g S4040L200 h 80 S4080L200AG SW4040L SW224L S4260L S4280L225AG SW4260L S5470L S5480L225AG 42 Suitable for use as service equipment. b May be installed on higher rated systems when protected by a circuit breaker with a higher AIR rating. c Indoor enclosures are 4 /4" wide by 3 7/8" deep. d Outdoor enclosures are 4 /2" wide by 4 /4" deep. e Suitable for use as service entrance equipment when not more than six main disconnecting means are provided. See article of the NEC. f ES Series single phase skus with a "G" suffix have ground bar included (factory installed). g Line and Neutral Lug Wire Range: 500 kcmil - #2 AL/CU h Available (made to order) in white by adding "W" to the end of the part number. -2 Siemens Industry, Inc. SPEEDFAX 207 Product Catalog Product Category RESI

13 ES Series -Phase Unassembled Load Centers Revised on 04/20/7 -phase, 3-wire SN, 20/240 Volts A Features n Available for the most popular ES Load Centers n Gives the ability to order in bulk n Enclosures will have minimal packaging for less hassle and waste at the job site n Keeps the covers separate to prevent damage or theft n Includes full size cardboard covers to keep the interior safe during painting n All main lug panels include factory installed ground bars Main Breaker ES Unassembled Load Centers Aluminum Bus / eres 60/75 Rated 22,000A IR Box Main Dimensions Height Width Depth Trim Catalog Number Pallet Quantity 25 SB2424B25 Main Breaker ST2424B SB3040B200 Main Breaker ST3040B SB4040B200 Main Breaker ST4040B200 d 30 Selectable Main ES Unassembled Load Centers / 200 eres Aluminum Bus Box Main Dimensions Height Width Depth Trim Catalog Number Pallet Quantity 50/200 SB3040C200G Convertible ST3040X /200 SB4040C200G Convertible ST4040X Main Lug ES Unassembled Load Centers Aluminum Bus / eres 60/75 Rated 00,000A IR Box Main Dimensions Height Width Depth Trim Catalog Number Pallet Quantity 25 SB2440L25G Main Lug ST2440L SB3040L25G Main Lug ST3040L SB3040L200G Main Lug ST3040L SB4040L200G Main Lug ST4040L Suitable for use as service equipment. May be installed on higher rated systems when protected by a circuit breaker with a higher AIR rating. ES Series single phase skus with a "G" suffix have ground bar included (factory installed). d Available (made to order) in white by adding "W" to the end of the part number. Siemens Industry, Inc. SPEEDFAX 207 Product Catalog -3

14 ES Series -Phase Special Load Centers Revised on 04/20/7 -phase, 3-wire SN, 20/240 Volts AC First Surge ES Load Centers Aluminum Bus /75 Rated, 22,000A IR Surge Protection S3054B200S060 60kA S4060B200S060 60kA 42 Outdoor Trailer Panels Aluminum Bus 6 / 200 eres 60/75 Rated 00,000A IR Main Breaker (inches) SW086L200T N/A N/A SW086B200T MBK200A Factory Installed 23 (inches) Value Pack Load Centers Load Center Breakers Included N0. of Aluminum Bus S2020B00P S2020B00 (3) Q20, () Q S3040B200P S3040B200 (3) Q20, () Q S3040L200P S3040L200 (3) Q20, () Q S4040B200P S4040B200 (3) Q20, () Q S3054B200P N/A (3) Q20, () Q Split Ground Series Load Centers / eres 6 / 200 eres Aluminum Bus Branch Indoor Enclosure NEMA Type S2030L25SG S3030B50SG S4040B200SG 36 (inches) Selectable Main Load Centers / eres Aluminum Bus Branch Indoor Enclosure NEMA Type Outdoor Enclosure NEMA Type 3R Available Kits Enclosure Enclosure Height (inches) Height (inches) Main Lug Main Breaker S2424C25 24 SW2424C25 27 ECMLK25 MBK00A, MBK25A S2040C SW2040C ECMLK225 MBK200A S3040C SW3040C ECMLK225 MBK50A, MBK200A S4040C SW4040C ECMLK225 MBK50A, MBK200A Load centers with white trim have increased lead time of 3-4 weeks. Sold in pallet quantities only. Additional charge will apply. Contact sales office for details. Indoor enclosures are 4 /4" wide by 3 7/8" deep. Breakers are shipped inside a sleeve located inside the load center. Outdoor enclosures are 4 /2" wide by 4 /4" deep. Main breaker rated 22,000A IR. Split Ground load centers have factory installed 00% neutral with factory bonded 75% ground. Selectable main load centers do not come with main lugs or main breakers. Those kits are sold separately. -4 Siemens Industry, Inc. SPEEDFAX 207 Product Catalog Product Category RESI

15 ES Series 3-Phase Main Lug & Main Breaker Load Centers 3-phase, 3-wire, 240 Volt AC or 3-phase, 4-wire, 20/240 or 20/208 Volts AC Main Breaker Aluminum Bus / eres 60/75 C Rated 0,000A IR Branch Indoor Enclosure NEMA Type Outdoor Enclosure NEMA Type 3R (inches) S224B SW224B S3030B S3042B S3042B S2442B SW2442B S4242B S3054B S3054B SW3054B S4260B SW4260B S4242B SW4242B (inches) Main Lug Aluminum Bus 2-70 / eres 60/75 Rated 00,000A IR Branch Indoor Enclosure NEMA Type Outdoor Enclosure NEMA Type 3R (inches) S224L325 2 SW224L S836L SW836L S2442L SW2442L S224L SW224L S2442L SW2442L S3054L SW3054L S4260L SW4260L S5470L (inches) May be installed on higher rated systems when protected by a circuit breaker with a higher AIR rating. Back fed main breaker. Indoor enclosures are 4 /4" wide by 3 7/8" deep. Outdoor enclosures are 4 /2" wide by 4 /4" deep. Suitable for use as service entrance equipment when not more than six main disconnecting means are provided. See article of the NEC. Rated 00,000A IR in series with breakers listed on wiring diagram. Available (made to order) in white by adding "W" to the end of the part number. Siemens Industry, Inc. SPEEDFAX 207 Product Catalog -5

16 EQ Load Centers Revised on 04/20/7 -Phase, 3-Wire/3-Phase, 3-Wire, 4-Wire Features n UL listed for 60/75 C conductors. See equipment markings for applications. n Copper bus standard. n Factory installed lock on indoor enclosure. n Outdoor enclosures use HV type hubs. See page -22. E3030MB400SCU Main Breaker ere a Ø, 3-Wire 20/240 Volts AC ere Branch Type QP Indoor Enclosure NEMA Type (65,000A IR) Outdoor Enclosure NEMA Type 3R (65,000A IR) Max. -Pole Max. 2-Poles Catalog Number c Std. Pkg. Dimensions (inches) Trim Catalog Std. Dimensions (inches) Height Width Depth Style Number Pkg. Height Width Depth d E4242MB300FCU Flush E4242MB300SCU Surface E3030MB400SCU Surface W3030MB400CU E4242MB400FCU Flush W4242MB400CU E4242MB400SCU Surface 3Ø, 3-Wire, 4-Wire 240 Volts AC Branch Type QP Indoor Enclosure NEMA Type (65,000A IR) Outdoor Enclosure NEMA Type 3R (65,000A IR) ere Max. Max. Catalog Std. Dimensions (inches) Trim Catalog Std. Dimensions (inches) -Pole 2-Poles Number c Pkg. Height Width Depth Style Number Pkg. Height Width Depth d E4242MB3300SCU Surface E3030MB3400SCU Surface E4242MB3400FCU Flush W4242MB3400CU E4242MB3400SCU Surface Main Lug 400 ere Ø, 3-Wire 20/240 Volts AC ere Branch Type QP Indoor Enclosure NEMA Type (65,000A IR) Outdoor Enclosure NEMA Type 3R (65,000A IR) Max. -Pole Max. 2-Poles Catalog Number c Std. Pkg. Dimensions (inches) Trim Catalog Std. Dimensions (inches) Height Width Depth Style Number Pkg. Height Width Depthd W0606ML400CU E3030ML400SCU Surface W3030ML400CU E4242ML400SCU Surface E4242ML400FCU Flush W4242ML400CU Ø, 3-Wire, 4-Wire 240 Volts AC Branch Type QP Indoor Enclosure NEMA Type (22,000A IR) Outdoor Enclosure NEMA Type 3R (22,000A IR) ere Max. Max. Catalog Std. Dimensions (inches) Trim Catalog Std. Dimensions (inches) -Pole 2-Poles Number Pkg. Height Width Depth Style Number Pkg. Height Width Depth d E3030ML3400SCU Surface E4242ML3400FCU Flush W4242ML3400CU E4242ML3400SCU Surface a UL listed as suitable for use as service equipment. b W0606ML4000CU rated at 22,000A IR. c Where noted suffix S = Surface, F = Flush. d Does not include 2" rainhead overhang. e Accepts up to six QN style breakers. f Suitable for use as service entrance equipment when not more than six main disconnecting means are provided. -6 Siemens Industry, Inc. SPEEDFAX 207 Product Catalog Product Category RESI

17 Generator Ready Load Centers -Phase, 3-WIre SN, 20/240Volts AC Generator Ready Load Centers The Siemens generator ready load center can save thousands of dollars in future generator installation expenses while keeping initial expenses to a minimum. Works with an automatic standby generator or a portable generator. Load Center Features n UL Listed n Indoor Type and outdoor Type 3R n 225A max rated n Flush or surface mounting n Fits between standard stud centers n Tin plated copper bus bars n 22 kaic rated n 20/240V ~ n Main lug convertible to main breaker with addition of MBK50A, MBK200A, or MBK225A n Main breaker convertible to main lug with use of lug kit part no. ECMLK225 n Installation of transfer mechanism can be performed at time of generator installation. NEMA Automatic transfer switch features: n UL Listed n Operates automatically when connected to generator n Transfers load from utility to generator and back to utility n Transfer switch (sold separately) catalog number: GENTFRSWTCH Indoor Enclosure NEMA Type Dimensions (inches) Height Width Depth G3042B200GEN G3042L225GEN G4254B200GEN G4254L225GEN GENTFRSWTCH Outdoor Enclosure NEMA Type 3R Dimensions (inches) Height Width Depth W3042B200GEN W3042L225GEN Q225S provided with GENTFRSWTCH for use with automatic transfer mechanism. 2 spaces and 2 circuits are reserved for standby generator installation. Field install breaker for voltage sensing required. NEMA 3R Siemens Industry, Inc. SPEEDFAX 207 Product Catalog -7

18 Riser Panel Load Centers Revised on 04/20/7 -Phase, 3-WIre SN, 20/240Volts AC Riser Panel Load Centers Riser panel load centers are ideal for high rise applications. The shifted interior provides room for conductors to pass through the load center. The tap kits allow the installer to tap off from those conductors to power the panel. Features n UL Listed for use in Ø and 3Ø riser gutter applications. n Copper bus standard. n Main lug factory standard - convertible to main breaker. n Neutrals aligned on left side- keeps way clear for riser cables. n Available in 25 and 200 amp models. n Invertible for left and right hand applications. ECRLK250 Riser Gutter Tap Kit The riser gutter tap kit (ECRLK250) allows the installer to tap off the main conductors, eliminating the need to cut completely through the conductor. The tap kit accepts 250 -/0 on the main conductor side and 250-#6 on the tap side. R632L25CU Riser Gutter The riser gutter (RAG24) is used to convert any load center 24 or larger into a riser panel. Features n Single and 3-phase applications n Compatible with any single or 3-phase Siemens load center 24" or higher n Flush trim included n Load center mounting hardware and pass through brush included (Catalog no. RAG24) Any Load Center 24" or larger RAG24 -phase, 3-wire SN, 20/240 Volts AC Aluminum Bus Aluminum Bus White Coating Copper Bus Dimensions (inches) Copper Bus White Coating Height Width Depth Acceptable Main Breaker Kits R632L25 R632L25W R632L25CU MBK00A,MBK25A R2424L25 R2424L25W R2424L25CU MBK00A, MBK25A R2442L25 R2442L25W R2442L25CU R2442L25CUW MBK00A, MBK25A R3042L200 R3042L200W R3042L200CU R3042L200CUW MBK50A, MBK200A The riser panels are single phase only, but can be fed from -phase or 3-phase systems running through the gutter trough area. ECRLK250 is sold separately -8 Siemens Industry, Inc. SPEEDFAX 207 Product Catalog

19 EQ Load Centers Small Circuit Load Centers -Phase, 3-WIre SN, 20/240Volts AC Features/Applications EQ Load Centers with main lugs feature a combination trim box in one package. n Interiors offer removal in seconds n Single phase n One piece bus bar construction designed for use only with circuit breakers n UL Listed n UL listed on 60/75 C conductors (see equipment markings for applications) n Positive load side circuit breaker hook rails n Outdoor Type 3R devices use HS Type hubs. See page -22. Small Circuit Load Centers Ideal for subfeed applications Renovation Panel Ideal for older home renovation projects where the distance between the studs is narrower than current construction practices. The narrower panel eliminates the need to notch out the existing studs. Spa Panels Spa Panels are ideal for outdoor applications requiring the use of ground fault protection, such as hot tubs. A factory installed 2-Pole GFCI breaker is provided, along with 2 extra circuits. Main Lugs with Aluminum Bus 00,000A IR 4 6 circuits, eres -Phase, 3-Wire, SN 20/240 Volts AC Branch Indoor Enclosure NEMA Type Outdoor Enclosure NEMA Type 3R Max. -Pole QP Max. 2-Poles Replace Suffix F (Flush) with S for Surface Mounting Std. Pkg. Dimensions (inches) Dimensions (inches) H W D Catalog Number Std Pkg. H W D E224ML00FG a 4 3/4 2 3/8 3 7/ E0408ML25F bde 5 2 5/8 6 5/8 3 /2 W0408ML25 bd 5 2 /4 6 4 / W0408L25SPA50 cdh 2 /4 6 4 / W0408L25SPA60 cdh 2 /4 6 4 / E086ML25F e 4 3/4 2 3/8 3 7/8 Main Lug and Main Breaker with Copper Bus 00,000A IR 4 6 circuits, eres -Phase, 3-Wire, SN 20/240 Volts AC Branch Indoor Enclosure NEMA Type Outdoor Enclosure NEMA Type 3R Max. -Pole QP Max. 2-Poles Catalog Number Std. Pkg. Dimensions (inches) Dimensions (inches) H W D Catalog Number Std. Pkg. H W D E020MB00FCGP g 4 3/4 2 3/8 3 7/ E224ML00FCU 4 3/4 2 3/8 3 7/ E086ML25FCU e 4 3/4 2 3/8 3 7/8 W086ML25CU e 4 3/4 2 /8 4 / E086ML25SCU 4 3/4 2 3/8 3 7/ W0406ML225CU b / W0404MB200CT jk 20 /8 4 3/ W0404MB50CTS k 20 /8 4 3/ W0404MB200CTS k 20 /8 4 3/4 a 70 amp maximum breaker. b Will not accommodate 2-pole GFCI or circuit breaker with shunt trip. c Can accommodate 2-pole GFCI breaker up to 50A. For 2-pole 60A GFCI, a restriction of #6 wire applies due to wire bend space of the enclosure. Will not accommodate circuit breaker with shunt trip. d 00 amp maximum breaker. e Suitable for use as service entrance equipment when a main breaker (25A maximum) is back-fed in a branch position and used with main breaker retainer clip (Cat. No. ECMBR). f Suitable for use as service entrance when not more than six main disconnecting means are provided. Check local codes and restrictions. g Two Q5 and one Q230 breaker included. h W0408L25SPA50 provided with factory installed QF50 and ground bar. W0408L25SPA60 provided with factory installed QF260 and ground bar. i Copper Bus load centers are recommended for those applications where the environment may be severe (i.e. farm and coastal areas). j 2" HS Type hub provided. k Type QNR main breaker factory installed. CSA Listed Cover plate included Product Category RESI Siemens Industry, Inc. SPEEDFAX 207 Product Catalog -9

20 EQ Load Centers Circuit Breaker Enclosures -Phase and 3-Phase, 240V AC Max. Features n Circuit breaker enclosures range from 60A to 225A, indoor and outdoor models n Designed for use exclusively with QP, QT, QPH, HQP, BQ, BQH, HBQ, QPP, QPPH, HQPP, QJ2, QJH2 and QJ2-H circuit breakers n UL listed n Suitable for use as service entrance equipment n UL listed for 60/75 C conductors (See equipment markings for applications) n Outdoor type 3R devices use HS type hubs (pg. -2) except for the W0204ML060 which uses the HA type hub W0202MB200CU E0303ML300CU Breaker Used Indoor Enclosure NEMA Type Outdoor Enclosure NEMA Type 3R Frame ere Catalog Std. Dimensions (inches) Catalog Std. Dimensions (inches) Type Poles Number Pkg. Height Width Depth Number Pkg. Height Width Depth -Phase, 3-Wire SN 20/240 Volts AC 60 2 E0204ML060S a 5 9 7/8 5 /8 2 5/8 W0204ML060 a /4 QP, QPH, 60 2 E0204ML060F 5 9 7/8 5 /8 2 5/8 HQP 00 2 E0202MB00 d 7 /8 7 3/8 4 5/6 W0202MB00CU d E0204ML25SCU 7 /8 7 /8 4 /4 W0204ML25CU 7 /8 7 3/8 4 5/6 QN, QNH, HQN 50 2 W0202MB50CU d 9 3/ W0202ML200CU 9 3/ E0202MB /8 8 /2 4 W0202MB200CU d 9 3/ QPP, QPPH, HQPP, QP W0406ML225CU b /8 QJ2, 50 2 WB250B e /8 4 5/6 QJH2, WB2200B e /8 4 5/6 QJ2-H WB2225 b /8 4 5/6 3-Phase, 3-Wire 240 Volts AC or 3-Phase, 4-Wire SN 20/208 Volts AC, 20/240, 240 Volts AC QP, QPH,HQP E0303ML300S c 7 /8 7 /8 4 /4 W0303ML300 c 7 /8 7 3/8 4 5/6 BQ, BQH, HBQ EB300S c 7 /8 7 /8 4 /4 WB300 c 7 /8 7 3/8 4 5/6 QJ2, QJH2, QJ2-H EB3225F b 27 0 /8 5 /8 WB3225 b 27 0 /8 5 9/6 a Will not accommodate 2-pole GFCI or circuit breaker with shunt trip. b 42,000A IR maximum. Copper wire only at 225A. c Can accommodate 2-pole GFCI breaker up to 50A. For 2-pole GFCI, a restriction of #6 wire applies due to wire bend space of the enclosure. Will not accommodate circuit breaker with shunt trip. d Main breaker factory installed. e QJ2 frame circuit breaker installed, rated 0,000A IR. CSA Listed. -20 Siemens Industry, Inc. SPEEDFAX 207 Product Catalog Product Category RESI

21 Load Centers Load Center OEM Interiors Ø: Small Circuit Main Lug Interiors s b Dimensions Height Width 60 I0204ML25CU I0303ML300CU I0408ML I086ML25CU I086ML25CUSP I0202L I220L200CT H W H W I220L200CT Ø: High Circuit Main Lug Interiors with Neutral Bars d Dimensions I224L25CU s b Height Width 25 I224L25CU I624L25CU I3040L25CU I086L200CT d I224L200CU I632L200CU I2040L200CU I3040L200CU I4040L200CU I4242L225CU H W H W Parallel Lug 3Ø: Main Lug Interiors I086ML25CU Dimensions s Height Width 25 SI224L325B SI224L3200B SI2442L3200B SI3054L3200B SI4242L3225B PI224L325CUB PI224L3200CUB PI836L3200CUB PI836L325CUB PI2442L3200CUB PI3054L3200CUB PI4242L3225CUB H W I0408ML25 H W Phase Ø: Parallel Lug Interiors with Neutral Bars Dimensions W s b Height Width 200 CTI2040L200CU CTI2440L200CU CTI3040L200CU H W H Lug Data Interior erage Wire range Torque I0204ML /0-4 AWG 45 lb. - ins. I0303ML /0-4 AWG 45 lb. - ins. I224ML /0-4 AWG 45 lb. - ins. I0408ML /0-4 AWG 45 lb. - ins. I086ML25CU/CUSP 60 2/0-4 AWG 45 lb. - ins. Single Phase 25 2/0-4 AWG 0 lb. - ins. Single Phase 200/ kcmil - 4 AWG 250 lb. - ins. Three Phase kcmil - 6 AWG 340 lb. - ins. Three Phase 200/ kcmil - 6 AWG 340 lb. - ins. I0202L200 3 Phase a UL Recognized Components. b The letters CU in any catalog number represent copper bus bars. c Feed thru lugs provided. d Convertible to main breaker using the MBK main breaker kits. Product Category RESI Siemens Industry, Inc. SPEEDFAX 207 Product Catalog -2

22 Load Centers Revised on 04/20/7 Load Center Accessories Catalog Number Description Pack Qty Ground Bar Kits (For ES and PL Load Centers) ECGB8 GROUND BAR KIT-8 POS ECGB82 GROUND BAR KIT-8 POS, 2/0 LUG EC2GB2 GROUND BAR KIT-2 POS EC2GB22 GROUND BAR KIT-2 POS, 2/0 LUG EC2GB5 GROUND BAR KIT-5 POS EC2GB52 GROUND BAR KIT-5 POS, 2/0 LUG EC3GB2 GROUND BAR KIT-2 POS EC3GB22 GROUND BAR KIT-2 POS, 2/0 LUG EC3GB27 GROUND BAR KIT-27 POS EC3GB272 GROUND BAR KIT-27 POS, 2/0 LUG EC3GB30 GROUND BAR KIT-30 POS EC3GB302 GROUND BAR KIT-30 POS, 2/0 LUG EC3GB352 GROUND BAR KIT-35 POS, 2/0 LUG EC3GB352G GROUND BAR KIT-35 POS, 2/0 LUG Ground Bar Kits (For Legacy Load Centers) ECGB5 GROUND BAR KIT-5 POS ECGB0 GROUND BAR KIT-0 POS ECGB0 GROUND BAR KIT-0 POS, /0 LUG ECGB4 GROUND BAR KIT-4 POS ECGB4 GROUND BAR KIT-4 POS, /0 LUG ECGB42 GROUND BAR KIT-4 POS, 2/0 LUG ECGB20 GROUND BAR KIT-20 POS ECGB20 GROUND BAR KIT-20 POS, /0 LUG ECGB202 GROUND BAR KIT-20 POS, 2/0 LUG ECINSGB5 INSULATED GROUND BAR KIT-5 POS ECINSGB4 INSULATED GROUND BAR KIT-4 POS ECINSGB20 INSULATED GROUND BAR KIT-20 POS Hubs ECHS000 HS TYPE CLOSURE PLATE ECHS075 HS TYPE HUB - 3/4" ECHS00 HS TYPE HUB - " ECHS25 HS TYPE HUB - /4" ECHS50 HS TYPE HUB - /2" ECHS200 HS TYPE HUB - 2" ECHS250 HS TYPE HUB - 2 /2" ECHA000 HA TYPE CLOSURE PLATE ECHA075 HA TYPE HUB - 3/4' ECHA00 HA TYPE HUB - " ECHA25 HA TYPE HUB - /4" ECHA50 HA TYPE HUB - /2" ECHV000 HV TYPE CLOSURE PLATE ECHV200 HV TYPE HUB - 2" ECHV250 HV TYPE HUB - 2.5" ECHV300 HV TYPE HUB 3" ECHV350 HV TYPE HUB - 3.5" ECHV400 HV TYPE HUB - 4" Lock Kits ECQFL2 ECQFL ECQFL3 FLUSH LOCK KIT FOR ULT., PL, ES, 3PH 00A-225A FLUSH LOCK KIT-REPLACEMENT FOR EQ LC ADD-A-LOCK (FLUSH LOCK ) FOR A LC Description Pack Qty Load Center Conversion Kits cd MBK00A MAIN BREAKER KIT 00-25A PH 22K MBK25A MAIN BREAKER KIT 25A PH 22K MBK50A MAIN BREAKER KIT 50A-225A PH 22K MBK200A MAIN BREAKER KIT 200A-225A PH 22K MBK225A MAIN BREAKER KIT 225A PH 22K MBK300 MAIN BREAKER KIT 00A 3PH QP 240V 0K MBK325R MAIN BREAKER KIT 25A 3PH 240V 0K, QR MBK350R MAIN BREAKER KIT 50A 3PH 240V 0K, QR MBK375R MAIN BREAKER KIT 75A 3PH 240V 0K, QR MBK3200R MAIN BREAKER KIT 200A 3PH 240V 0K, QR MBK3225R MAIN BREAKER KIT 225A 3PH 240V 0K, QR MBK325HR MAIN BREAKER KIT 25A 3PH 240V 22K, QR MBK350HR MAIN BREAKER KIT 50A 3PH 240V 22K, QR MBK375HR MAIN BREAKER KIT 75A 3PH 240V 22K, QR MBK3200HR MAIN BREAKER KIT 200A 3PH 240V 22K, QR MBK3225HR MAIN BREAKER KIT 225A 3PH 240V 22K, QR MBK325HHR MAIN BREAKER KIT 25A 3PH 240V 65K, QR MBK350HHR MAIN BREAKER KIT 50A 3PH 240V 65K, QR MBK375HHR MAIN BREAKER KIT 75A 3PH 240V 65K, QR MBK3200HHR MAIN BREAKER KIT 200A 3PH 240V 65K, QR MBK3225HHR MAIN BREAKER KIT 225A 3PH 240V 65K, QR HMBK325HR MAIN BREAKER KIT 25A 3PH 240V 00K, QR HMBK350HR MAIN BREAKER KIT 50A 3PH 240V 00K, QR HMBK375HR MAIN BREAKER KIT 75A 3PH 240V 00K, QR HMBK3200HR MAIN BREAKER KIT 200A 3PH 240V 00K, QR HMBK3225HR MAIN BREAKER KIT 225A 3PH 240V 00K, QR ECMLK25 PH MAIN LUG CONVERSION KIT 00-25A ECMLK225 PH MAIN LUG CONVERSION KIT A ECMLK325 3 PH MAIN LUG CONVERSION KIT 00-25A ECMLK PH MAIN LUG CONVERSION KIT A Lug Kits ECCS COLLAR STRAP FOR GRD BARS #4-/0 ECCS2 COLLAR STRAP FOR GRD BARS #6-250 ECLKB NEUTRAL LUG KIT WITH BOND TAB ECLK3 NEUTRAL LUG KIT #-300 FOR EQIII LC ECLK-2 NEURTAL LUG KIT #2 TO /0 FOR EQIII LC ECLK2 NEUTRAL LUG KIT #4-2/0 FOR EQIII LC, PL, ES ECLK2SC 2/0 LUG FOR 25AMP NEUTRAL FEEDER ECLK225 25A SUB FEED LUGS-USES 2 SPACES ECLK A-225A SUB FEED LUGS-USES 4 SPACES ECLK3225 3P SUB FEED LUGS-USES 6 SPACES ECRLK250 RISER LUG KIT 250 KCMIL 3 Miscellaneous Load Center Accessories ECCP PKG OF 00 CIRCUIT DIRECTORY 00 ECQF3 QP/BQ/ED2 FILLER PLATE 5 ECMBF25 PH 00&25A MAIN BREAKER FILLER PLATE EC3PMFP 3 POLE MAIN FILLER PLATE, QJ EC3PMFPR 3 POLE MAIN FILLER PLATE, QR ECSMK SURFACE MOUNT /4" SPACE KIT FOR LC'S 4 ECTS2 LC TRIM SCREWS 6 ECTS2W LC TRIM SCREWS WHITE 6 ECLCHINGE GREY LC HINGES 00 ECADHLCDIRLBL ADHESIVE LC DIRECTORY LABELS 00 ECSIELATCH SIEMENS LC LATCHES 25 ECBONDSCRW LC BOND SCREW 0 ECSN SCREWS & NUTS FOR HC HUB-BOTTOM USE 4 RAG24 RISER AUX GUTTER 24" ECAFL ARC FLASH LABEL 0 Neutral Bar Kits ECLNB4 MLO NEUTRAL BAR KIT-4 POS ECCNB6 CONVERTIBLE LC NEUTRAL BAR KIT-6 POS ECMLK25 PH MAIN LUG CONVERSION KIT 00-25A The pack quantity is the number that is sold in a pack. Items listed on this page must be ordered in multiples of pack quantities but items are priced per each. For example, ECRLK250 come 3 to a pack so must be ordered in multiples of 3 but pricing would be individual unit price times 3. Bar has green-colored screws. QR Main Breaker Kits include a QR filler plate. d Main Breaker Kits include line terminal barriers. -22 Siemens Industry, Inc. SPEEDFAX 207 Product Catalog

23 Load Centers Load Center Accessories Lug Kit, 3-Pole, Subfeed or Feed thru Applications ECLK PH Main Lug Conversion Kit 50A-225A ECMLK225 Main Breaker Kit 200A - 225A, PH 22K MBK200A 3-Pole Main Breaker Kit MBK3200 Main Breaker Retainer Kit for EQ Load Centers ECMBR Main Breaker Retainer kit for PL, ES, & Ultimate Load Centers ECMBR2 Ground Bar Kit 20 POS. 2/0 Lug ECGB202 Ground Bar Kit, ECGB4 Neutral Lug Kit, ECLK-2 wire range #2- AWG Cu or Al Neutral Lug Kit, ECLK3 wire range #-300 MCM Neutral Lug Kit, ECLK2 wire range #4-#2/0 AWG Cu or Al For use on Ground Bar only Collar Strap, Wire Range; ECCS; ECCS2 Add-A-Lock (Flush Lock) ECQFL For EQ load centers Filler Plate, ECQF3 Add-A-Lock (Flush Lock), ECQFL2 PL, ES, Ultimate Load Centers and EQ III up to 225A Add-A-Lock (Flush Lock), ECQFL A Load Centers Siemens Industry, Inc. SPEEDFAX 207 Product Catalog -23

24 Load Centers Load Center Accessories Revised on 04/20/7 Load centers and meter combos Touchsafe barriers are required for any single main service entrance application for a panel covered under UL 67. Line Terminal Barriers will be included in Main Breaker Load Centers and Single Main Meter Combos manufactured after January, 207. Single phase and 3-phase main breaker kits will include a barrier. Field installable kits are being created for replacements if needed and line terminal barriers are being added to hold down kits that can be used in back-fed applications. The barriers are designed to have minimal interference during load center installation, and can be removed and reattached as necessary. Catalog number Description ECLTB For EQ Main Breakers/MBK kits 00A-25A ECLTB2 For EQ Main Breakers/MBK kits 50A-225A ECLTB3 For QN / QNR type breakers ECLTB4 For QR 3 phase breakers ECMBR For 2 Pole QP / MP-T type breakers for EQIII (extruded basepan) and Line 5 Load Centers ECMBR2 For 2 Pole QP / MP-T type breakers to be used with Ultimate LCs (now ES / PL), Murray or Rock Solid ECMBR3 For 3 Pole QP / MP-T type breakers to be used with PL, ES 3 phase load centers ECLX387HD For 2 Pole MP-T type breakers in legacy Murray load centers -24 Siemens Industry, Inc. SPEEDFAX 207 Product Catalog

25 Load Centers Manual Transfer Interlock Kits for Load Centers and Meter Combinations Convert load centers or meter combinations into standby power panels Standard features n UL listed for use in most Siemens load centers and meter combinations Panels in which the bussing or wire forms from the meter socket land on main lugs are not acceptable for use in standby systems because turning the main breaker to OFF does not prevent feedback to the utility power lines. Examples of such panels include catalog numbers that start with the following letters. MC0606L200* MM0406L* MC22L200* Utility main breaker Standby power main breaker n Suitable for use with optional standby systems in accordance with article 702 of the National Electric Code n Corrosion resistant finish n Easy assembly requiring no modifications to the load center or meter combination n Remains attached to the main breakers when load center cover Wire forms or bussing To activate standby power the utility main breaker must be in the OFF position to prevent dangerous feedback between the power sources. Acceptable usage of Interlock Kits by load center/meter combination catalog numbers ES Series Load Centers can utilize interlock kits:, 2, 5, 6, 7. Kits 3 and 4 can also be used on main breaker panels. PL Series Load Centers can utilize interlock kits:, 2, 3, 4, 5, 6, 7. Numbers through 9 in these tables represent the last digit in each interlock kit catalog number. Example: = ECSBPK0 When used in horizontal positions as typical in most load centers, ECSBPK07 is recommended for use only with QNR type circuit breakers. Standby power interlock kits are not intended for use with AFCI, GFCI, 3-pole or /2 frame circuit breakers and 4 space, 25 amp load centers. Siemens Meter Combinations MC0408B200RGA 8 MC020B00S 2 MC0408B200RT 8 MC224B00EFC 2 MC0408B200T 8 MC224B00ESC 2 MC086B50JLT 9 MC224B25EFC 2 MC086B50RCT 8 MC224B25ESC 2 MC086B50TH 5 7 MC2040B50JLC 8 MC086B200CT 8 MC2040B200JLC 8 MC086B200EFN 2 MC2040B200R 5 7 MC086B200ESN 2 MC2040B200RC 9 MC086B200EST 2 MC2040B200RJBC 9 MC086B200JLT 9 MC2442S200FC 2 MC086B200RCT 8 MC2442S200SC 2 MC086B200RGA 8 MC3042B200FED 3 MC086B200RTH 5 7 MC3042B200JLC 8 MC086B200T 7 MC3042B400FD 5 7 MC086B200TH 5 7 MC3042B400SC 5 7 MC086B350RLTM 5 MC3042B400SCS 5 7 MC086B400RLTM 5 MC3042B400SD 5 7 MC086B400SCS 5 7 MC3042B400SDS 5 7 MC020B00F 2 MC4040S200SC 5 Siemens type EQ load centers using a 4-pole main breaker do not have a kit available to interlock this main to branch circuits. Branch circuit positions can be interlocked. Siemens Industry, Inc. SPEEDFAX 207 Product Catalog -25

26 Load Centers Manual Transfer Interlock Kits for Load Centers and Meter Combinations Prevents dangerous feedback between two sources of power Manual Transfer Interlock Kits a Catalog number ECSBPK0 Usage Information For use on load centers or meter combinations that will accept 2-pole circuit breakers opposite one another as shown. Utility main breaker types Standby main breaker types QP, QPH, HQPH QP, QPH, HQPH Interlock Number ECSBPK02 For use on load centers or meter combinations that will accept 2- or 4-pole next to a 2-pole circuit breaker side by side as shown. QP, QPH, HQPH QP, QPH, HQPH 2 ECSBPK03 For use on UltimateTM and Rock Solid load centers, 50 amp and higher, to connect the main breaker to a 2-pole circuit breaker. MBK50A, MBK200A, OR MBK225A QP, QPH, HQPH 3 ECSBPK04 For use on Ultimate and Rock Solid load centers, 25 amp and lower, to connect the main breaker to a 2-pole circuit breaker. MBK00A or MBK25A QP, QPH, HQPH 4 ECSBPK05 For use on load centers or meter meter combinations that will accept a QNR (MD-TR) frame circuit breaker next to a 2-pole circuit breaker as shown. QNR, QNRH, HQNR QP, QPH, HQPH 5 ECSBPK06 For use on load centers or meter combinations that will accept a QN (MD-T) frame circuit breaker next to a 2-pole circuit breaker as shown. QN, QNH, HQN QP, QPH, HQPH 6 ECSBPK07 For use on load centers or meter combinations that will accept two QNR (MD--TR) circuit breakers side by side as shown OR will accept two QN (MD--T) circuit breakers side by side as shown. QNR, QNRH, HQNR, QN, QNH, HQN QNR, QNRH, HQNR QN, QNH, HQN 7 ECSBPK08 For use on 8 space, over/under, OH/UG feed meter combinations as shown. Limited application to specific catalog numbers. QPP, QPPH QP, QPH, HQPH 8 ECSBPK09 For use on 20 space, over/under, OH/UG feed meter combinations as shown. Limited application to specific catalog numbers. QPP, QPPH QP, QPH, HQPH 9 Manual breaker interlock kits are attached to the breakers not the trim of the load center. These kits take up 2 spaces adjacent to the 2 pole breaker being interlocked. Those spaces cannot accommodate filler plates. -26 Siemens Industry, Inc. SPEEDFAX 207 Product Catalog

27 Load Centers -Phase Indoor and -Phase & 3-Phase Outdoor Enclosures Knockout Diagrams Siemens Industry, Inc. SPEEDFAX 207 Product Catalog -27

28 Load Centers 3-Phase Indoor and Riser Enclosures Knockout Diagrams New Riser Panel KO Diagram 6/7/08 (0) K.O.s for /2", 3/4", " Conduit (8) K.O.s for /2", 3/4" Conduit (42) K.O.s for /2" Conduit (2) K.O.s for -/2", 2", 2-/2" Conduit (4) 5/6" K.O.s RAG24 KO Dwg /5/ (4) K.O.s for -/2", 2", 2-/2" Conduit (8) K.O.s for ", -/4", -/2", 2", 2-/2" Conduit (4) Mounting Holes All Riser Panels RAG24-28 Siemens Industry, Inc. SPEEDFAX 207 Product Catalog

29 Load Centers Outdoor Enclosures Knockout Diagrams 2 Type "HV" Hub Openings 4 Mounting Holes.28 Dia 2 K.O.'s For.5",.75", Conduit 4 K.O.'s For.5",.75", ",.25" Conduit 5 K.O.'s For ",.25",.50", 2", 2.50" Conduit 2 K.O.'s For.75", ",.25",.50" Conduit 2 K.O.'s For 2.50", 3", 3.50" Conduit Outdoor 400A Load Center W0406ML25CU W0204ML060 W0408ML25 Siemens Industry, Inc. SPEEDFAX 207 Product Catalog -29

30 Load Centers Outdoor Enclosures Knockout Diagrams WB2225 and WB32225 W0204ML25 W0303ML300 WB300 W062ML25 W086ML25-30 Siemens Industry, Inc. SPEEDFAX 207 Product Catalog

31 Load Centers Indoor Enclosures Knockout Diagrams 24 K.O.'s For.5",.75" Conduit Indoor A Load Center 8 K.O.'s For.5",.75", ",.25" Conduit E062ML25 E086ML25 E086ML25 E224ML00F E224ML00F E0408ML25 E0408ML25 E0303ML300SCU E0303ML300SCU EB300 EB300 E0204ML060 E0204ML060 Siemens Industry, Inc. SPEEDFAX 207 Product Catalog -3

32 Load Centers Cross Reference Ultimate Load Center Cross Reference to ES Series and PL Series Phase Type Current Sku ES Series PL Series New P3040L200SG New P4040L200SG New - Higher P4260L225CUSG New - Higher S3054L200 P3054L200CU New - Higher S5470B225 P5470B225CU New - Higher S5470L225 P5470L225CU New - Higher SW3054L200 PW3054L200CU G22L25 S22L25 - G22L25CU P22L25CU G224B00 S224B00 - G224B00CU P224B00CU G224L25 S224L25 - G224L25CU P224L25CU G224L25CUSG P224L25CUSG G224L200CU S224L200 P224L200CU G624B00 S624B00 - G624B00CU P624B00CU G624B00W S624B00W - G624L25 S624L25 - G624L25CU P624L25CU G624L25CUSG P624L25CUSG G630B50 S630B50 - G2020B00 S2020B00 - G2020B00CP S2020B00P - G2020B00CU P2020B00CU G2020L25 S2020L25 - G2020L25CU P2020L25CU G2020L25CUW S2020L25W G2030B50 S2030B50 G2030B50CU P2030B50CU G2030L25CUSG P2030L25CUSG G2030L50 S2030L50 G2030L50CU P2030L50CU G2030L50CUSG P2030L50CUSG G2040B200 S2040B200 G2040B200CU P2040B200CU G2040L200 S2040L200 G2040L200CU P2040L200CU G2424B00CU P2424B00CU Phase Indoor G2424B25 S2424B25 G2424L25 S2424L25 G2424L25W S2424L25W G2430B50 S2430B50 G2430L25CUSG P2430L25CUSG G2440B200 S2440B200 G2440L25CU S2440L25 P2440L25CU G2440L200 S2440L200 G2440L200CU P2440L200CU G3030B00CU S3030B00 P3030B00CU G3030B50 S3030B50 G3030B50CU P3030B50CU G3030L200 S3030L200 G3030L200CU P3030L200CU G3030L200W S3030L200W G3040B200 S3040B200 P3040B200 G3040B200CP S3040B200P G3040B200CU P3040B200CU G3040L25CU P3040L25CU G3040L25CUW S3040L25W G3040L200 S3040L200 P3040L200 G3040L200CP S3040L200P G3040L200CU P3040L200CU G3040L200CUSG P3040L200CUSG G4040B200 S4040B200 P4040B200 G4040B200CP S4040B200P G4040B200CU P4040B200CU G4040B200W S4040B200W P4040B200W G4040L25CU S4040L25 P4040L25CU G4040L200 S4040L200 P4040L200 G4040L200CU P4040L200CU G4040L200CUSG P4040L200CUSG G4242B225CU S4260B225 P4260B225CU G4242L225CU S4260L225 P4260L225CU G2020B00SP S2024B00 P2024B00CU G2020L25SP S2020L25G G2024L25SP S2024L25/S2024L25G P2024L25CU G2424L25SP S2424L25G G3030B25CU S3030B25 P3030B25CU G3040L25 S3040L25/S3040L25G G4040B200CUSG P4040B200CUSG -32 Siemens Industry, Inc. SPEEDFAX 207 Product Catalog

33 Load Centers Cross Reference Ultimate Load Center Cross Reference to ES Series and PL Series Phase Type Current Sku ES Series PL Series Phase Outdoor 3 Phase Indoor Outdoor W086B200CT SW086B200T PW086B200TC W086L200CT SW086L200T PW086L200TC W22L25CU SW22L25 PW22L25CU W224B00CU SW224B00 PW224B00CU W224L25CU SW224L25 PW224L25CU W224L200CU SW224L200 PW224L200CU W224L225CU SW224L225 PW224L225CU W624B00CU SW624B00 PW624B00CU W624L25CU SW624L25 PW624L25CU W2020B00CU SW2020B00 PW2020B00CU W2030L50CU SW2030L50 PW2030L50CU W2040B200CU SW2040B200 PW2040B200CU W2040L200CU SW2040L200 PW2040L200CU W2424L25CU SW2424L25 W3040B200CU SW3040B200 PW3040B200CU W3040L25CU SW3040L25 PW3040L25CU W3040L200CU SW3040L200 PW3040L200CU W4040B200CU SW4040B200 PW4040B200CU W4040L200CU SW4040L200 PW4040L200CU W4242B225CU SW4260B225 PW4260B225CU W4242L225CU SW4260L225 PW4260L225CU New S4242B350 New Higher P5470B3225CU New Higher S5470L3225 P5470L3225CU G224L325CU S224L325 P224L325CU G224L3200CU S224L3200 G836L350CU S836L350 G2442B350CU S2442B350 P2442B350CU G2442B350CU22 P2442B350CU G2442L350CU S2442L350 G2442L3200CU S2442L3200 P2442L3200CU G3030B300CU S3030B300 P3042B300CU G3030B300CU22 P3042B300CU G3042B3200CU S3054B3200 P3054B3200CU G3042L3200CU S3054L3200 P3054L3200CU G4242B3200CU S4260B3200 P4260B3200CU G4242B3225CU S4242B3225 P4260B3225TCU/ P4260B3225CU G4242L3225CU S4260L3225 P4260L3225CU W224L325CU SW224L325 PW224L325CU W224L3200CU SW224L3200 W836L350CU SW836L350 W2442B350CU SW2442B350 W2442L350CU SW2442L350 W2442L3200CU SW2442L3200 PW2442L3200CU W3042B3200CU SW3054B3200 PW3054B3200CU W3042B3200CU22 PW3054B3200CU W3042L3200CU SW3054L3200 PW3054L3200CU W4242B3200CU SW4260B3200 PW4260B3200CU W4242B3200CU22 PW4260B3200CU W4242B3225CU SW4242B3225 PW4260L3225CU W4242L3225CU SW4260L3225 Siemens Industry, Inc. SPEEDFAX 207 Product Catalog -33

34 Circuit Breakers Arc-Fault and Ground-Fault Breakers Revised on 0/30/7 Selection/Wiring Diagrams Arc-Fault Circuit Interrupters (AFCI) AFCI s detect arcing faults (an unintentional arcing condition in a circuit) that standard circuit breakers are unable to detect. The device is intended to mitigate the effects of arcing faults by functioning to de-energize the circuit when an arc-fault is detected. Combination Type AFCI Detects all three possible types of arc faults: line-to-ground, line-to-neutral, and series. Breaker Type QAF2/QAFH2/HQAF2 -Pole 20V AC QAF2/QAFH2 2-Pole 20/240V AC ere Branch-Feeder AFCI Detects line-to-ground and line-to neutral arcs. QAF2/QAFH2/HQAF2 -Pole 20V AC NEW 5 20 Dual Function AFCI/GFCI 0,000 A IR Catalog No. QA5AFC QA20AFC Q25AFC Q220AFC QA5AF QA20AF QAF2/QPF/QE/QPF2 Accessories 22,000 A IR Catalog No. QA5AFCH QA20AFCH Q25AFCHn Q220AFCHn QA5AFHn QA20AFHn 65,000 A IR Catalog No. QA5AFCHHn QA20AFCHHn QA5AFHHn QA20AFHHn The Dual Function Circuit Breaker combines Combination Type AFCI and GFCI, protecting against both Arc Faults and (5mA) Ground Faults. The device includes the Self Test feature, making it the first in class in electrical safety for homeowners. QFGA2/QFGAH2/ HQFGA2 -Pole 20V AC Description Padlocking Device -Pole Padlocking Device 2-Pole Handle Block 5 20 Q5DF Q20DF ECPLD ECPLD2 ECBX23M Q5DFHn Q20DFH Ground-Fault Circuit Interrupters (GFCI) Q5DFHHn Q20DFHHn Provides Class A (5mA) ground fault protection. Intended for personnel protection. Includes Self Test as an added safety feature. Breaker Type QPF2/QPHF2/HQPF2 -Pole 20V AC Plug-in QPF/QPHF 2-Pole 20/240V AC Plug-in ,000 A IR Catalog No. QF5A a QF20A a QF30A a QF25A QF220A QF230A QF240A QF250A QF260A 22,000 A IR Catalog No. QF5AHn a QF20AHn a QF30AHn a QF25AHn QF220AHn QF230AHn QF240AHn QF250AHn QF260AHn Ground Fault Equipment Protection (30mA) Provides protection of equipment from damaging line-to-ground faults currents. De-energizes the circuit for all ungrounded conductors of the circuit. QE/QEH -Pole 20V AC Plug-in QE/QEH 2-Pole 20/240V AC Plug-in QE5 QE20 QE30 QE25 QE220 QE230 QE240 QE250 QE260 QE5Hn QE20Hn QE30Hn QE25Hn QE220Hn QE230Hn QE240Hn QE250Hn QE260Hn 65,000 A IR Catalog No. QF5AHHn a QF20AHHn a QF30AHHn a UL Listed -Pole Combination Type AFCI -Pole Branch Feeder AFCI -Pole GFCI -Pole Equipment Protection Wiring Diagrams HACR Rated 2-Pole Combination Type AFCI -Pole Dual Function AFCI/GFC 2-Pole GFCI 2-Pole Equipment Protection n Built to order. Allow 8-0 weeks for delivery. a UL Listed as SWD (Switching Duty) Rated, suitable for 20V AC Fluorescent Lighting. Add WG to the part number for the WireGuide version. -34 Siemens Industry, Inc. SPEEDFAX 207 Product Catalog Product Category RESI

35 Circuit Breakers Intelli-Arc Diagnostic Tool Intelli-Arc Diagnostic Tool, Part Number: IDT5000 The Siemens Intelli-Arc Diagnostic Tool helps to accurately diagnose the circuit in which a fault has occurred. When used in conjunction with good troubleshooting techniques, this tool allows the electrical contractor to determine and locate the root cause or source of the fault. The Intelli-Arc Diagnostic Tool presents information as to the type and magnitude of fault. Since the fault may not cause an AFCI to trip for various reasons, i.e. duration too short, current level too low, the tool provides an indication showing how close an event is to causing an AFCI to trip. Features Wireless communication indicator (A) Ground fault indicator (B) Arc fault indicator (C) Communication with base unit Clear (last event) Power button Push and hold "clear" button while pressing "power" button to test the hand-held functionality Hook location for attaching base unit to the load center Power indicator Communication indicator with hand-held The goal of the diagnostic tool is to speed the troubleshooting process for the electrical contractor. The device drastically improves the accuracy of the troubleshooting process. This, in turn, will significantly reduce the number of visits to the problem site. Every intent of this device is directed as saving the electrical contractor time for each branch circuit that must be evaluated. The Intelli-Arc Diagnostic Tool can be used with any circuit breaker regardless of brand. Hand-held unit Base unit Wire terminals to load Wire terminals to breaker Two state-of-the-art technologies combined in one device! Dual Function Circuit Breakers: QFGA2/QFGAH2/HQFGA2 Introducing the Dual Function Circuit Breaker that provides Arc Fault and Ground Fault protection in one device. The 204 National Electric Code requires Arc Fault protection on Kitchen and Laundry circuits where Ground fault protection is currently a requirement. One solution to meet this code is to pair an AFCI circuit breaker with a GFCI receptacle. The Dual function breaker will replace the Arc fault breaker and the Ground Fault receptacle. Additionally, the breaker will help eliminate the use of two separate devices and improve cost savings. Features Plug-in or bolt-on branch circuit breakers for Siemens single phase load centers Self Test feature as required by UL 699 effective June 205 Saving time ease of installation only One product to install vs. Two Saving money Two safety devices combined into One. LED trip indicator a Siemens exclusive! Available with interrupting rating of 0kA, 22kA or 65kA UL Listed Torque rating: 25 lb. in. Padlocking device available, use catalog number ECPLD -Pole Dual Function Circuit Breaker Both lugs at the same angle - for easier wiring Siemens Industry, Inc. SPEEDFAX 207 Product Catalog -35

36 Circuit Breakers Type QP with INSTA-WIRE Continuous 40 C Type QP Type QPH Type HQP 0,000A IR 22,000A IR 65,000A IR -Pole Plug-In (20V AC) e 0 Q0 5 Q5c Q5H c Q5HHn c 20 Q20c Q20H c Q20HHn c 25 Q25 Q25Hn Q25HHn 30 Q30 Q30H Q30HHn 35 Q35n Q35Hn Q35HHn 40 Q40 Q40H Q40HHn 45 Q45n Q45Hn Q45HHn 50 Q50 Q50H Q50HHn 60 Q60 Q60Hn Q60HHn 70 Q70 Q70Hn Q70HHn 2-Pole Plug-In (Common-Trip 20/240V AC) 0 Q20 5 Q25 Q25H Q25HH 20 Q220 Q220H Q220HH 25 Q225 Q225Hn Q225HHn 30 Q230 Q230H Q230HH 35 Q235 Q235Hn Q235HHn 40 Q240 Q240H Q240HHn 45 Q245 Q245Hn Q245HHn 50 Q250 Q250H Q250HH 60 Q260 Q260H Q260HH 70 Q270 Q270H Q270HH 80 Q280 Q280Hn Q280HHn 90 Q290 Q290H Q290HHn 00 Q200 Q200H Q200HH 0 Q20 Q20H Q20HHn 25 Q225 Q225H Q225HH 2-Pole Plug-In (Common-Trip 240V AC) 5 Q25R 20 Q220R 30 Q230R 40 Q240R 50 Q250R 3-Pole Plug-In (Common-Trip 240V AC) 5 Q35 Q35H Q35HHn 20 Q320 Q320H Q320HH 25 Q325 Q325Hn Q325HHn 30 Q330 Q330H Q330HH 35 Q335 Q335Hn Q335HHn 40 Q340 Q340H Q340HH 45 Q345 Q345Hn Q345HHn 50 Q350 Q350H Q350HH 60 Q360 Q360H Q360HH 70 Q370 Q370H Q370HHn 80 Q380 Q380H Q380HHn 90 Q390 Q390H Q390HHn 00 Q300 Q300H Q300HH Q20 Q220 Q320 QP / QPH / HQP Internal Accessories Control Voltage AC Field/Factory Installed 20V Shunt Trip add suffix 00S0n Factory 24V Shunt Trip add suffix 00S07n Factory 20V Auxiliary Switch add suffix 0n b Factory Modifications Description 400 Hz Calibration add suffix Y h Marine 50 C Ambient Calibration add suffix M Fungus Proofing add suffix F For external accessories please refer to page -43. n Built to order. Allow 2-3 weeks for delivery. a UL Listed for use with 60/75 wire through 40 amps, UL listed for use with 75 wire only for 50 amps and above, HACR rated. \b A and B contacts. c UL Listed for frequent switching applications (SWD). 20V AC Fluorescent Lighting. d UL Listed for use on 3-phase grounded B systems 0,000 for this application. e Shipped 2 per sleeve. f Shipped 6 per sleeve. g Shipped 4 per sleeve. h UL Listed 5 KA IR. i Type QP, UL listed for 6 AWG conductors and multiple wires. -36 Siemens Industry, Inc. SPEEDFAX 207 Product Catalog Product Category RESI

37 Circuit Breakers Duplex, Triplex and Quadplex Plug-In Breakers Duplex Circuit Breakers Breaker Type QT -Pole 0K AIC 20V AC Triplex Circuit Breakers Breaker Type QT 2-Pole 0K AIC 20/240V AC Inner Poles Common Trip ere 5 5 Q55 Q55NC a 5 20 Q520 Q520NC a Q2020 Q2020NC a Q n Q Q Q3030 Q3030NC a SHIPPING: 2 per carton, (Wt. 4.8 lbs.) ere Single Pole Common-Trip 2-Pole Catalog Number 5 5 Q255CT 5 20 Q2520CT 5 25 Q2525CTn 5 30 Q2530CT 5 35 Q2535CTn 5 40 Q2540CT 5 45 Q2545CTn 5 50 Q2550CT Q22020CT Q22025CTn Q22030CT Q22035CTn Q22040CT Q22045CTn Q22050CT Q23030CT SHIPPING: 6 per carton, (Wt. 4.9 lbs.) QT Duplex These space saver duplex breakers combine two independent /2" breaker poles in a common unit. This unit plugs into one load center stab and requires one panel space. HACR rated. QT Triplex These space saver triplex breakers provide a 2-pole common trip breaker for 20/240V AC circuits and two single poles for 20V AC circuits. Triplex require two panel spaces. HACR rated. Quadplex Circuit Breakers ere Breaker Type QT 2-Pole 0K AIC 20/240V AC Inner and Outter 2 Poles Common Trip Common-Trip 2-Pole Outside Common-Trip 2-Pole Inside Catalog Number 5 5 Q255CT Q2530CT Q22020CT Q22050CT Q23020CT Q23025CT Q23030CT Q23050CT Q24020CT Q24030CT Q24040CT2 SHIPPING: 6 per carton, (Wt. 4.8 lbs.) QT Quadplex These space saver quadplex breakers provide two sets of common trip, two-pole breakers for 20/240V AC circuits, and require two panel spaces. HACR rated. For external accessories, please refer to page -43. For inches / millimeters conversion, see Application Data section. n Built to order. Allow 2 3 weeks for delivery. a Non-CTL. For replacement use only in panels manufactured before 968 Product Category RESI Siemens Industry, Inc. SPEEDFAX 207 Product Catalog -37

38 Circuit Breakers Special Application Breakers HID Lighting For high-intensity discharge lamp loads having in-rush currents above the instantaneous trip setting of a standard breaker. Breaker Type QP -Pole 20V AC QP 2-Pole 20/240V AC Wiring Diagram Figure Figure 2 Complete Breaker UL Unenclosed ere 5 Q5HID a n 20 Q20HID a 30 Q30HID 5 Q25HID 20 Q220HIDn 30 Q230HIDn Molded Case Switch For applications that do not require overcurrent protection. QP -Pole 20V AC QP 2-Pole 20/240V AC Figure 00 Q00S Figure Q230S Q250S Q260S Q225S Switching Neutral Figure Figure 2 No-Noise For applications that require a reduction in the 60-cycle hum of a standard breaker. Figure 3 Figure 4 QP 2-Pole 20/240V AC Figure Q250NNn Q260NN Switching Neutrals Used where all conductors are required to be disconnected. Neutral pole of the circuit breaker does not connect to load center bus. One side is wired to neutral and the other side to the device. QG 2-Wire Common Trip 20V AC QG 3-Wire Common Trip 20/240V AC Figure QG25 QG220 Figure 4 20 QG320 Wiring Diagrams n Built to order. Allow 2 3 weeks for delivery. Note: All circuit breakers on this page are 0K AIC a UL Listed as SWD (Switching Duty) Rated, suitable for 20V AC Fluorescent Lighting. -38 Siemens Industry, Inc. SPEEDFAX 207 Product Catalog Product Category RESI

39 Circuit Breakers 3/4 Inch Plug-In Breakers Features n 3/4" format n HACR Rated n UL Classified for use in certain Square D load centers Type QD Circuit Breakers The Type QD circuit breaker line is available in -pole and 2-pole common trip versions listed on this page. The circuit breakers are UL Classified and UL Listed. All QD breakers are supplied with load side connectors suitable for 60/75 C wire and are calibrated for 40 C maximum ambient applications. UL Classified Siemens Type QD circuit breakers are UL Classified for use in specific Square D load centers in place of Square D Type QO circuit breakers. A Panelboard Compatibility List packaged with each QD breaker shows which type QD circuit breakers are acceptable for use in Square D load centers. The interrupting rating on these circuit breakers is 0,000A IR maximum and they are not series rated with Square D circuit breakers or equipment. This UL Classification allows a Siemens Type QD circuit breaker to be used in place of a Square D Type QO circuit breaker in those load centers that are specifically shown on the Panelboard Compatibility list. For additional information, contact your local Siemens sales engineer. Shipping Weights Number of Number Per Shipping Poles Carton Weight (lbs.) Panelboard Compatibility List Listed Panelboards Square D s QO2L30F/S QO2-4L70F/S QO2-4L70TS QO2-4L70RB QO6-2L00F/S QO6-2L00DF/S QO6-2L00TF/S QO6-2L00DTF/S QO6-2L00RB QO8-6L00F/S QO8-6L00DF/S QO8-6L00TF/S QO8-6L00DTF/S QO8-6L00RB QO2M00/RB QO6M00/RB QO20M00/RB QO24M00 QO2L00DF/S QO2L00RB QO2-20M00/RB QO2-20M00TF/S D20 -Pole 2-Pole Continuous Current 20V 20/240V Common 40 C 5 D5 a D25 20 D20 a D D30 D D40 D D50 D D60 D260 QO2M00/RB QO6-20M00/RB QO6M00/RB QO20M00/RB QO2L25G/RB QO2-24L25G/RB QO2-24L25GWGC QO6L25G QO6-24L25G/RB QO2-24L25/RB QO20-24L25G QO20-24L25GWGC QO20L25G QO24L25G/RB QO24M25/RB QO6L25/RB QO6-2M25FTRB QO6-24L25/RB QO20L25/RB QO20-24L25/RB QO24L25/RB QO20-30L50G QO20-30M50/RB QO24L50G QO24M50 QO30L50G/RB QO30M50/RB QO6L50/RB QO6M50/RB QO6-30L50/RB QO8-6M50FTRB QO20-30M50/RB QO20-30M50TF/S QO20-30L50 QO24L50/RB QO24M50/RB QO30L50/RB QO30M50/RB QO8-6M200FT/RB QO2L200G/RB QO20-40M200/RB QO20-40M200TC QO24M200 QO30L200G/RB D220 QO30-40M200 QO30M200/RB QO30-40L200G/RB QO40M200/RB QO6L200/RB QO6M200/RB QO8-6M200FTRB QO20-40L200/RB QO20-40M200TF/S QO20-40M200/RB QO24L200/RB QO24M200/RB QO30L200/RB QO30M200/RB QO30-40L200/RB QO30-40M200/RB QO40M200/RB QO40M225 QO42L225G/RB For inches / millimeters conversion, see Application Data section. a UL Listed for frequent switching applications (SWD). 20V AC Fluorescent Lighting. One or two load conductors. Product Category RESI Siemens Industry, Inc. SPEEDFAX 207 Product Catalog -39

40 Circuit Breakers Revised on 04/20/7 Main and Branch Circuit Breakers Breaker Type QN 2-Pole 20/240V AC QNH 2-Pole 20/240V AC HQN 2-Pole 20/240V AC ere Catalog Number Catalog Number 50 QN250 QN250R b 0 75 QN275n QN275R b n QN2200 QN2200R b 0 50 QN250H QN250RH b QN275Hn QN275RH b n QN2200H QN2200RH b HQN250 HQN250R b HQN275n HQN2200 HQN2200R b 65 UL Interrupting s (ka) Requires 4 panel spaces, 2 adjacent and 2 opposite. SHIPPING: per carton (Wt. 3 lbs.) QNR e QN e Main Breaker Kits For use in PL, ES, and Ult Load Centers d UL Type ere Catalog Number For use in EQIII Load Centers UL Type ere Catalog Number EQ MBK00A EQ MBK00 22 EQ MBK25A EQ MBK25 22 EQ MBK50A EQ MBK50 22 EQ MBK75n 22 EQ MBK200A EQ MBK EQ MBK225A EQ MBK UL Interrupting s (ka) EQ9675 Breaker Type QPJ c 3-Pole 240V AC ere Catalog Number 25 QPJ QPJ QPJ UL Interrupting s (ka) Requires 6 spaces due to cross over design. Fits only EQIII A 3-phase load centers SHIPPING: 5 per carton (Wt. 7 lbs.) MBK (00,25)A MBK (50,200,225)A Breaker Type QPP 2-Pole 20/240V AC QPPH 2-Pole 20/240V AC HQPP 2-Pole 20/240V AC HQPPH 2-Pole 20/240V AC ere Catalog Number 25 Q225B 0 50 Q250B 0 75 Q275Bn Q2200B Q2225B 0 25 Q225BH Q250BH Q275BHn Q2200BH Q2225BHn Q225BHHn Q250BHH Q275BHHn Q2200BHH Q2225BHHn HQ200BHn HQ225BHn HQ250BHn HQ275BHn HQ2200BHn HQ2225BHn 00 UL Interrupting Breaker s (ka) Volts AC 20/240 QPJ 2-Pole QPP For inches / millimeters conversion, see Application Data section. n Built to order. Allow 2 3 weeks for delivery. a All circuit breakers on this page are common trip. b Reverse handle. c CSA Listed. d MBK00A for use in 00 and 25A load centers. MBK25A for use in 25A load centers. MBK50A for use in 50, 200 and 225A load centers. MBK200A for use in 200 and 225A load centers. MBK225A for use in 225A load centers. MBK75A for use in 200 and 225A load centers. e QNR required for horizontal applications or vertical applications where the lugs are facing up. The QN breaker is required for vertical applications where the lugs are facing down as shown. -40 Siemens Industry, Inc. SPEEDFAX 207 Product Catalog Product Category RESI

41 Circuit Breakers Line Diagrams/Dimension Drawings -Pole 2-Pole 3-Pole 3" 2 3 /8" 3 /8" QP, QPH, HQP Type QT Type QPF, QPHF, QE, QAF2, QAF2H Type EQ868, EQ8682 Type EQ8693, EQ8695, EQ8696 Type QPJ Type QN, QNH, HQN Type QNR, QNRH, HQNR Type QPP, QPPH, HQPP, HQPPH a All standard circuit breakers are calibrated to 40 C maximum ambient application. Siemens Industry, Inc. SPEEDFAX 207 Product Catalog -4

42 Circuit Breakers Revised on 04/20/7 Lug Data Circuit Breaker Type Circuit Breaker ere LOAD SIDE Cables Per Connector Connector Wire Range QP, QPH, HQP, Plug-in 0 2 #4-#6 AWG Cu QP & 2-Pole Only QT #8 AWG CU-Al QPF, QPHF 5 30 QAF2, QAFH2, QFGA2, QFGAH #4 #6 AWG Cu #4 #6 AWG Al #8 #6 AWG Cu #8 #4 AWG Al #8-#2/0 AWG Cu #8-#2/0 AWG Al #6-#4 AWG Cu-Al (#3 AWG compatible with QPH & HQP) #4 #6 AWG Cu #4 #6 AWG Al #8 #6 AWG Cu #8 #4 AWG Al #4 #0 AWG Cu #2 #8 AWG Al #8 #6 AWG Cu #8 #4 AWG Al #4 #2 AWG Cu #2 #0 AWG Al QD #4 #8 AWG Cu Only #4 #2 AWG Cu 5 20 #2 #0 AWG Al #0 #8 AWG Cu #0 #6 AWG Al #8 #6 AWG Cu #8 #4 AWG Al QN, QNH, HQN # 300kcmil Cu-Al QS, QSH, QSHH, HQS, HQSH #3 300kcmil Cu-Al EQ868-Ultimate, PL, ES 00 #4 3/0 AWG Cu-Al EQ8682-Ultimate, PL, ES 25 #4 3/0 AWG Cu-Al EQ8693-Ultimate, PL, ES 50 # 300kcmil Cu-Al EQ8695-Ultimate, PL, ES 200 # 300kcmil Cu-Al EQ8696-Ultimate, PL, ES 225 # 300kcmil Cu-Al QPP, QPPH, HQPP, HQPPH EQ9675-EQIII 00 EQ9677-EQIII 25 EQ9683-EQIII 50 EQ EQ9685-EQIII 200 EQ9686-EQIII 225 # AWG Cu #2/0 AWG Al #/0 AWG Cu #3/0 AWG Al #2/0 AWG Cu #4/0 AWG Al #3/0 AWG Cu 250kcmil AWG Al #4/0 AWG Cu 300kcmil AWG Al #8-#2/0 AWG Cu #8-#2/0 AWG Al #8-#2/0 AWG Cu #8-#2/0 AWG Al #/0 AWG Cu #3/0 AWG Al #3/0 AWG Cu 250kcmil AWG AL #3/0 AWG Cu 250kcmil AWG Al #4/0 AWG Cu 300kcmil AWG Al QPJ #2 300kcmil Cu-Al -42 Siemens Industry, Inc. SPEEDFAX 207 Product Catalog

43 Circuit Breakers Circuit Breaker Accessories Circuit Breaker Accessories For Use With Breaker Type Number of Poles Standard Package Padlocking Device For locking breaker in OFF position. Note ON position does not affect breaker fuctionally ECPLD Type QP, BL, QAF2, QPF2, QE, QT-Duplex, BQ, BQXD P 3 Pieces ECPLDR Type QP, BL, QAF2, QPF, QE, QT-Duplex, BQ, BQXD P 3 Pieces (Red Color) ECPLD2 Type QP, BL, QAF2, QPF, QE, QT-Triplex & Quadplex, BQ, 2P 3 Pieces BQXD ECPLD2R Type QP, BL, QAF2, QPF, QE, QT-Triplex & Quadplex, BQ, 2P 3 Pieces BQXD (Red Color) ECPLD3 Type QP, BL, QAF2, QPF, QE, BQ 3P Piece US2:ECPLD3R Type QP, BL, QAF2, QPF, QE, BQ (Red Color) 3P Piece ECQLD3 Type QP, BL, BQ, BQXD P 0 Pieces ECQLD4 Type QT-Duplex QT-Duplex Breakers 0 Pieces ECQLN MBKA, QN, QNR n/a Piece ECQTH4 Type QP, BL, BQH Designed for (3) P Breakers Piece Handle Tie Provide simultaneous swiching of 2 adjacent handles. ECQTH2 Type QT Duplex Designed for (2) QT Duplex Breakers 25 Pieces ECQTH3 Type QP, BL 2P 50 Pieces Mechanical Interlock ECQML2 Type QP, BL, BQ Interlock Bracket Designed for Breaker 0 Pieces Handle Blocking Device For holding breaker in ON or OFF position. Not a lockout/tagout device ECQL Type QP, BL, BQ, BQXD P 0 Pieces ECBX23M Type QT-Duplex /2 Breakers 0 Pieces Main Breaker Retainer ECMBR EQ Load Centers Piece ECMBR2 PL, ES, and Ultimate Load Centers: 2-pole QP Piece ECMBR3 PL, ES, and Ultimate Load Centers: 3-pole QP Piece Mounting Accessories MB20 Type BQ, BQH Mounting Clips P 20 Pieces FP9508 Type BQ, BQH FACE MOUNT PLATE P 0 Pieces FP9555 Type BQ, BQH FACE MOUNT PLATE 2P 0 Pieces FP9556 Type BQ, BQH FACE MOUNT PLATE 3P 0 Pieces SMB6R Type BQ MOUNTING BRACKET P, 2P, 3P 6 Pieces TCH65K Type BQ MOUNTING ADAPTER 500 Pieces BR2 Type BQ, BQH, BQXD Back Mounting Plates 2P 0 Pieces BR3 Type BQ, BQH, BQXD Back Mounting Plates 3P 0 Pieces BR4 Type BQ, BQH, BQXD Back Mounting Plates 4P 0 Pieces I0204ML25CU Type QP Back Mounting Plates P, 2P 0 Pieces I0303ML300CU Type QP Back Mounting Plates 3P 0 Pieces Replacement Lugs TAQ Type BQ, NGG 00A Al Cu LGS n/a 6 Pieces TCQ Type BQ, NGG 40A Al Cu LUGS n/a 6 Pieces Finger Shield BQFSK Type BQXD Finger Shield (Bulk Pack) n/a 000 Pieces BQFS2 Type BQXD Finger Shield n/a 2 Pieces Filler Plate ECQF3 Filler Plate n/a 5 Pieces For a complete list of standby power mechanical interlock kits, see page -25 For use with Ultimate Load Center Main Breakers Not suitable for use on 5-50A, 0 AIC Type QP Circuit Breakers QP Type includes QPH, HQP BL Type includes BLH, HBL BQ Type includes BQH, HBQ QAF2 Type includes QAFH2, BAF2, BAFH2, QFGA2, QFGAH2, BFGA2, BFGAH2 QPF Type includes QPHF, BLF, BLHF QE Type includes QEH, BLE, BLEH Product Category RESI Siemens Industry, Inc. SPEEDFAX 207 Product Catalog -43

44 Circuit Breakers Circuit Breaker Accessories Padlocking Device ECPLD ECQLD3 ECPLD2 ECPLDR/2R/3R (Single pole pictured. 2-/3-pole available) ECQLD4 ECQTH4 Handle Tie Handle Blocking Device ECQL ECQTH2 ECQTH3 ECBX23M Main Breaker Retainer Mechanical Interlock ECMBR ECMBR2 ECQML2 Mounting Accessories FP9508 FP9556 MB20 SMB6R I0204ML25 FP Siemens Industry, Inc. SPEEDFAX 207 Product Catalog

45 Surge Protection Circuit Breaker and Surge Protective Device (SPD) Features n 2 inch wide plug-on design Includes (2) Pole circuits breakers No loss of load center spaces n Easy to install and perfect for retrofit n LEDs provide protection status Circuit Breaker and Surge Protective Device (SPD) Benefits By installing a Siemens Circuit Breaker and Surge Protective Device (SPD) in the load center of the residence, surge protection is provided for all branch circuits. Two green LED indicator lights are provided to show that surge protection is provided for all circuits connected to the load center. These breakers should be used for circuit protection of frequently used household or facility circuits because the lights and devices connected to these circuits provide an effective indication that surge protection is being provided. The circuit breaker and SPD utilize Siemens-built 50V AC, 40mm, metal oxide varistors (MOVs). The maximum impulse rating for the SPD module is 40kA. The standard interrupting rating for the circuit breakers is 0k AIC. All Type QP circuit breakers and SPD are plug-on style, with load terminals provided. The devices are rated for 20/240V AC and are calibrated for 40 degrees C maximum ambient applications. Breaker Type ere Surge Type QP - Pole 20/240V AC (2) 5 QSA55SPD SPD 0K AIC (2) 20 QSA2020SPD SPD erage Number of Poles Initial Clamping Level Transient Energy Transient Suppression Voltage Peak Current (impulse) Discharge Voltage Characteristic Discharge Current Withstand Circuit Breaker Interrupting Listings/Certifications QSA55SPD QSA2020SPD 5 or 20 (2) -Pole Circuit Breakers 240 Volts 360 Joules line-to-neutral 720 Joules line-to-line 500 volts peak, line-to-neutral 000 volts peak, line-to-line 40, ,000A, 800 volts (both line-to-neutral) 0,000 amperes line-to-neutral 0,000A, 20/240V AC UL, CSA Meets UL 449 4th Edition For warranty information please refer to the surge website Product Category RESI Siemens Industry, Inc. SPEEDFAX 207 Product Catalog -45

46 s usa.siemens. com/surge s Surge Protection Power Service Entrance Surge Protection FirstSurge TM - Power, Plus, or Pro n 4th Listed, Type 2, Surge Protective Device (SPD n Surge Current Capacities: 60,000 A,FirstSurge Power (FS060) 00,000 A,FirstSurge Plus (FS00) 40,000 A, FirstSurge Pro (FS40) n 3 Stage Commercial Grade Notification: Protection Status LEDs Audible Alarm Flashing Red Service LED n Ground Reference Monitoring (GRM) n 0 year product & connected equipment warranty* * See for warranty terms and conditions. FirstSurge FS060, FS00, FS40 Surge Type FirstSurge Power FirstSurge Plus FirstSurge Pro FS060 FS00 FS40 A C To Protected Loads AC Surge Protection UL and CSA Listings 449 4th Edition & CSA 22.2 No Surge Spike Capacity 60kA, 00kA, or 40kA Line Voltage 20/240 Phase 50/60 Hz UL 449 4th Edition VPR L-N, L-G, N-G: 600 V; L-L: 900V Rated Voltage (MCOV) L-N, L-G, and N-G: 50V; L-L: 300V Short Circuit Current (SCCR) 00kA Inominal (I n ) 20kA Response Time < nanosecond Enclosure NEMA 4X Indoor and Outdoor Rated Product Warranty 0 years N BREAKER G usa.siemens. com/surge Use closest breaker to SPD Locate SPD close to intended breaker (max. 30A) Keep Leads Short as Possible Avoid Sharp Bends Rotate FirstSurge such that LED indicator is most visible Outdoor installation requires appropriate weather sealing at nipple (gasket, sealing conduit, etc.) Type SPD / Surge Arrestor Replacement TPS3 03 TPS3 03 is a UL 449 4th Edition 50 ka Type compact surge protective device that can be used as a replacement secondary surge or lighting arrestors. Having a Type designation allows for flexible electrical system connection location (line or load side) as well as UL 96A compliance (@ 20 ka I n ). TPS3 03 Key Features n UL 449 4th Edition Listed Type n Type Rated SPD n 50 ka Per Phase Surge Current n 20 ka I n (Most models) n 200 ka SCCR (Most models n UL 96A Lightning Protection Master Labeling compliant (@ 20 ka)) n Every MOV is monitored n Mounts external to electrical distribution equipment Recommend for Line Side or Load Side Applications n Standard compact NEMA 4X polycarbonate enclosure n Modes of Protection: L-N or L-G and L-L n Standard Monitoring: LED Indicator n Dimensions: 3.25 x 3.25 x 3.3 (82.6 mm x 82.6 mm x 83.8 mm) n Weight: 2 lb. (0.9 kg) n 2 Year Product Warranty Available Options: n Dry contacts & Audible Alarm (option D ) TPS3 03 Ordering Information Catalog # TPS3 03 TPS3 0 DIN RAIL Mounting Voltage Code A = 20/240 V, Ø, 3W B = 20/240 V, 3Ø, 4W Surge Current (ka) 05 = 50 ka per phase Options D = Dry contact & audible alarm C = 20/208 V, 3Ø, 4W N = Adds N-G D = 240 V, 3Ø, 3W Protection E = 277/480 V, 3Ø, 4W F = 480 V, 3Ø, 3W G = 600 V, 3Ø, 3W K = 380/220 V, 3Ø, 4W L = 600/347 V, 3Ø, 4W Example: TPS3C0305D0 = Type SPD for a 208/20V application with a surge current capacity of 50 ka per phase, in a standard NEMA 4X enclosure with dry contacts and audible alarm option. When an option is not selected, include a zero (0) in the field. Available Accessories: Ordered Separately RMSIE = Remote monitor -46 Siemens Industry, Inc. SPEEDFAX 207 Product Catalog Product Category RESI

47 SPD - Surge Protective Device Telephone Service Entrance Surge Protection FSPHONE & FSPHONE4X n UL/cUL listed n Hardwired Telephone/Modem/Fax/DSL protection n Exceptionally fast response time n Low insertion loss n Available with or without enclosure n 5 Year product warranty* * See for warranty terms and conditions. The Siemens FSPHONE & FSPHONE4X is a 2 pair, hardwired surge protector designed to stop surges from entering through the main telephone incoming service connection. It is equipped with a failshort device to permanently ground the telephone line in the event of a power cross. The FSPHONE is designed for indoor applications where the FSPHONE4X is useed for outdoor mounting is required. The FSPHONE4X includes the FSPHONE plus a weatherproof enclosure to facilitate indoor or outdoor applications. The enclosure is molded of temperature and humidity resistant thermoplas-tic to resist cracking and discoloration. The cover FSPHONE AC Surge Protection Catastrophic Surge Circuit Yes Spike Capacity 200 s Let Through Voltage <270V Overcurrent Protection Yes Response Time < nanosecond Environmentally Sealed Yes UL/cUL Listings 497A Meets Telcordia (formallly Bellcore) GR-974-CORE Requirements for Telecommunications Line Yes Protectors Product Warranty 5 years can be secured with a tie wrap or similar locking device. Surge Type Telco FSPHONE Telco FSPHONE4X FSPHONE4X Coaxial Service Entrance Surge Protection FSCATV n UL/cUL listed surge protection n Rated for CATV, DSS, TV, VCR, and Cable Modem n Easy to install n Standard Female to Female F connector n Low insertion loss n Automatic recovery n 5 Year product warranty* * See for warranty terms and conditions. FSCATV Siemens FSCATV shields coaxial connected electronics in residential and light commercial applications against electrical transient damage, including lightning, from entering through the main cable connection. FSCATV includes a section of coaxial cable with female to female splice for line side application. The Siemens warranty covers product defects for 5 years. To have complete protection for your equipment, home, or business, it is important to protect AC power lines and all data lines the equipment is connected through. AC Surge Protection Frequency Range Catastrophic Surge Circuit Spike Capacity Impedance Overcurrent Protection Return Loss Insertion Loss UL/cUL Listings Meets IEEE C62.4. Requirements Product Warranty DC thru.5 GHz Yes 5000 s, 8/20 µsec 75 Ohms Yes GHz <0.dB 497B Yes 5 Years Surge Type Coaxial FSCATV Product Category RESI Siemens Industry, Inc. SPEEDFAX 207 Product Catalog -47

48 AC Disconnects -Phase, NEMA 3R Rated WN2060 WN2060GFCI WF2060PL WNAS2060GFCI Steel AC Disconnects a ere Disconnect Horse Power Dimensions Pallet Type Height Width Depth Qty. 30 Fused Pullout WF Fused Pullout WF Non-fused Pullout WN Non-automatic Switch WNAS Plastic AC Disconnects a ere Disconnect Horse Power Dimensions Pallet Type Height Width Depth Qty. 30 Fused Pullout WF2030PL Fused Pullout WF2060PL Non-fused Pullout WN2060PL Non-Fused Pullout WN2060PLX Non-automatic switch WNAS2060PL Steel AC Disconnects with 5 GFCI Receptacle a ere Disconnect Horse Power Dimensions Pallet Type Height Width Depth Qty. 30 Fused Pullout WF2030GFCI Fused Pullout WF2060GFCI Non-fused Pullout WN2060GFCI Non-automatic Switch WNAS2060GFCI Wire Range Table Copper Aluminum Connector Solid Stranded Solid Stranded Line #4-8 #4-3 #2-8 #2-3 Load #4-8 #4-3 #2-8 #2-3 Neutral #2-8 #2-2 #2-8 #2-2 Equip. Grnd #2-8 #2-2 #2-8 #2-2 a Accepts Class H Fuse -48 Siemens Industry, Inc. SPEEDFAX 207 Product Catalog Product Category RESI