ATyS t M - ATyS g M Automatic Transfer Switching Equipment from 40 to 160 A

Size: px

Start display at page:

Download "ATyS t M - ATyS g M Automatic Transfer Switching Equipment from 40 to 160 A"

Gervase George
5 years ago
Views:

TyS t M - TyS g M utomatic Transfer Switching Equipment Transfer switches new The solution for > High Rise uildings > Data centre > Healthcare buildings TyS g M I-0-II P

The TyS g M is also available in P for single phase applications.

genset applications (TyS g M). They are intended for use in low voltage power supply systems where a brief interruption of the load supply is acceptable during transfer.

Thanks to the design that allows commissioning through just one potentiometer (4 on the TyS g M) and four DIP switches, a screwdriver is all that is required to configure the parameters.

tests on load...) together with the monitoring of the voltage and frequency of both sources for three-phase and single-phase networks.

with or without priority, preferred source selection) together with the monitoring of the voltage and frequency of both sources for three-phase networks.

1 TyS t M - TyS g M utomatic Transfer Switching Equipment Transfer switches new The solution for > High Rise uildings > Data centre > Healthcare buildings TyS g M I-0-II P atys-mg_001_b_1_cat Function TyS t M I-0-II 4P atys-mt_001_b_1_cat TyS t M and TyS g M are three-phase (4P) automatic transfer switches with positive break indication. The TyS g M is also available in P for single phase applications. The TyS t M and TyS g M both include TyS d M functionality together, with an integrated controller for automatic transfer dedicated to mains/mains applications (TyS t M) and mains/ genset applications (TyS g M). They are intended for use in low voltage power supply systems where a brief interruption of the load supply is acceptable during transfer. dvantages Fast commissioning TyS t M and g M transfer switches offer significant time saving during commissioning (the process takes to 3 minutes). Thanks to the design that allows commissioning through just one potentiometer (4 on the TyS g M) and four DIP switches, a screwdriver is all that is required to configure the parameters. TyS g M: specifically designed for mains/ genset applications The TyS g M integrated controller has been designed to provide specific functions for these applications (genset startup, tests on load...) together with the monitoring of the voltage and frequency of both sources for three-phase and single-phase networks. TyS t M: specifically designed for mains/ mains applications The TyS t M integrated controller has been designed to provide all the functions necessary for these applications (operation with or without priority, preferred source selection) together with the monitoring of the voltage and frequency of both sources for three-phase networks. Secured configuration settings In order to prevent any risk of unintended change to the configured settings, a sealable cover is available as an accessory. Strong points > Fast commissioning > TyS d M functions plus an integrated TS controller dedicated to mains/mains or mains/genset applications > Secured configuration settings Conformity to standards > IEC > IEC > G pprovals and certifications (1) (1) Product reference on request. (1) Only on two pole versions

2 TyS t M - TyS g M utomatic Transfer Switching Equipment What you need to know The TyS t M and TyS g M are automatic transfer switching equipment that include a fully integrated TS controller. These products are self powered from incoming supplies: 30 VC ( VC), 50/60 Hz (45/65Hz). s TyS t M No. of poles Network (VC) TyS t M ridging bars Voltage sensing and power supply tap Terminal shrouds uxiliary contact block Sealable cover 40 4P 30/ P 30/ P 30/ P 30/ P 30/ P 30/ P pieces pieces (1) 1 piece Separate common points () Linked common points () (1) The three-phase version (4 P), for upstream and downstream protection, please order the reference twice. For the single-phase version ( P) please order the reference once. () 1 NO/NC contact block for positions I, 0 and II. TyS g M No. of poles Network (VC) (3) TyS g M ridging bars Voltage sensing and power supply tap Terminal shrouds uxiliary contact block Sealable cover 40 P P 30/ P P 30/ P P 30/ P P 30/ P P 30/ P P pieces pieces (1) 1 piece Separate common points () Linked common points () P P P P 30/ (1) The three-phase version (4 P), for upstream and downstream protection, please order the reference twice. For the single-phase version ( P) please order the reference once. () 1 NO/NC contact block for positions I, 0 and II. (3) For 17/30 VC networks, please contact your SOCOMEC office.

ccessories ridging bars d to bridge the outgoing common connection between switch I and switch II. The bridging bar does not reduce the connection capacity of the cage terminals. No.

Pack 40 160 pieces 1399 4006 The single-pole voltage sensing tap can be mounted in any of the terminals (incoming) without reducing their connecting capacity.

3 ccessories ridging bars d to bridge the outgoing common connection between switch I and switch II. The bridging bar does not reduce the connection capacity of the cage terminals. No. of poles P P P P atysm_05_a Voltage sensing and power supply tap It allows connection of x 1.5 mm² voltage sensing or power cables. Pack pieces The single-pole voltage sensing tap can be mounted in any of the terminals (incoming) without reducing their connecting capacity. atysm_06_a Terminal shrouds Protection against direct contact with terminals or connecting parts. dvantages of the terminal shrouds Perforations built in to the terminal shrouds allow remote thermographic inspection without the need to remove the shrouds. Tamper-proof seals can be fitted for increased security. Position top and bottom (1) (1) composed of pieces (4P). Mounting For upstream and downstream protection of three-phase products (4 P), please order the reference twice. For the single-phase products ( P) please order the reference once. atysm_07_a uxiliary contact uxiliary contacts for position indication. maximum of two auxiliary contact blocks can be fitted to each product. Each auxiliary contact block integrates 3 NO/NC auxiliary contacts, one per position (I, 0, II). Type Separate common connection Linked common connection The TyS d M s is supplied with one auxiliary contact block fitted as standard; This /C block has separate common points. Characteristics: 50 VC / 5 maximum. 4 VDC / maximum. access_353_a access_398_a

4 Sealable cover Prevents access to the TyS t M and g M configuration panel (seals and screws are included). No. of poles P P atysm_313_a Polycarbonate enclosure Dedicated to the installation of a three-phase TyS M, it enables easy integration of a compact transfer switch solution. H x W x D (mm) x 385 x atysm_036_b_1_cat Extension box for polycarbonate enclosure Combined with the polycarbonate enclosure, the extension unit provides additional space in order to connect 70 mm² cables to the TyS M with ease atysm_039_a_1_x_cat

5 ccessories (continued) Residential enclosure Dedicated to the implementation of a single-phase TyS M, this plastic enclosure provides a compact IP41 transfer switch solution with easy integration. H x W x D (mm) x 305 x atysm_196_a_1_cat uto-transformer For use with TyS M in 400 VC three-phase applications that does not have a distributed neutral. The TyS M includes integrated sensing and power supply circuits, therefore a neutral connection is required for 400 VC three-phase applications. When no neutral connection is available this autotransformer (400/30 VC, 400 V) provides the 30 VC required for the TyS to function trafo_165_b_1 Double power supply - DPS llows an TyS d M to be supplied by two 30 VC, 50/60 Hz networks to have full control in terms of transfer to and from any position with any one of the power supplies available. Input The input is considered active from 00 VC. Maximum voltage: 88 VC. Internal protection: each input is fuse protected Connection on terminals: max. 6 mm. Modular device: 4 module width. 3 Input 1 Input Output 30 VC 0 VC 30 VC (Input 1) 0 VC 30 VC 30 VC (Input ) 30 VC 30 VC 30 VC (Input 1) 0 VC 0 VC 0 VC atys_616_a_1_cat atys_61_a cat Description of accessories DPS and. Input 3. Output

Remote interfaces for TyS p M To remotely display source availability and position indication typically used on the front of a panel when the TyS M is enclosed.

6 Remote interfaces for TyS p M To remotely display source availability and position indication typically used on the front of a panel when the TyS M is enclosed. The remote interface is powered directly from the TyS M via the RJ45 connection cable. Maximum cable length: 3 m. D10 To display source availability and position indication on the front panel of an enclosure. Protection degree: IP1 D0 In addition to the functions of the TyS D10, the D0 displays measurements and enables control and configuration from the front of the display panel. Protection degree: IP1 Door mounting holes Ø.5. TyS M connection via RJ45 cable, not isolated. Cable not provided Description of accessories D D atys_564_c_1_cat atys_597_a_1_cat Interfaces are self powered from the TyS M 96 x 96 Ø.5 = = Drillings atys_565_c_1_cat atys_161_a_1_x_cat Connection cable for remote interfaces To connect between a remote interface (type D10 or D0) and an TyS p M. Type Length RJ45 cable 3 m Characteristics: RJ45 8 wire straight-through, non isolated cable. Length 3m. acces_09_a cat Power connection terminals The power connection terminals allow conversion of the cage terminals into bolt-on type connection terminals, enabling connection of up to two 35mm² cables or one 70mm² cable. Compatible with aluminium terminals. Each power connection terminal is provided with separation screens (1) For complete conversion, order 3 times the reference. acces_5_a_1_cat

Enclosed transfer switch solutions General characteristics dapted to mechanical risk and dust hazard. Integrated bridging bar Protection degree: IP3x or IP54. Colour: RL 7035.

7 Enclosed transfer switch solutions General characteristics dapted to mechanical risk and dust hazard. Integrated bridging bar Protection degree: IP3x or IP54. Colour: RL Cable gland plates: top and bottom. Material: steel, thickness 1. mm. Coating: epoxy polyester powder. Wall mounting: 4 fixing lugs supplied loose. Door: hinged metal door, front door cut out 37.4x47.6 mm. Door lock: 3 mm double bar key (included). s TyS d M No. of poles IP 3X IP P P P P P P TyS g M No. of poles IP 3X IP P P P P P P coff_366_b TyS p M + COM RS485 No. of poles IP 3X IP P P P P P P ccessories Customer fit Description Solid neutral Kit IP Dimensions Weight (excluding accessories): 15 kg. Connection (without power connection terminals): min. Cu 10 mm², max. 70 mm². atysm_10_a_1_x_cat

8 Dimensions TyS M 40 to 160 Single-phase TyS M Three-phase TyS M atysm_04_a_1_x_cat atysm_07_a_1_x_cat uxiliary contact ( max) Single-phase TyS M - Door cut-out atysm_008_b_1_x_cat atysm_034_a_1_x_cat x M6 1. uxiliary contact ( max). 34 Three-phase TyS M - Door cut-out Terminals and connections Single-phase TyS d M Three-phase TyS d M atysm_05_a_1_x_cat 7 atysm_040_e_1_x_cat 7 1 : position I control : position II control 3 : position 0 / C control 4 : power supply I (30 VC) 5 : power supply II (30 VC) 6 : voltage tap 7 : auxiliary contact block - 1 NO/NC contact per position I, 0, II (factory fitted) C C 5 : bridging bar (accessories) : single-phase voltage sensing tap (accessories) C: F1 / F = fuse 10 gg 4 4

9 Terminals and connections (continued) Three-phase TyS t M atysm_1_a_1_x_cat 1 preferred source (network) alternate source (network) 1 : position 0 control : preferred source selection 3 : automatic mode inhibition 6 : availability S1 or S : bridging bar (accessories) : auxiliary contact block - 1 NO/NC contact per position I, 0, II (accessories) Single-phase TyS g M Three-phase TyS g M 1 preferred source alternate source atysm_06_a_1_x_cat atysm_1_a_1_x_cat 1 : manual retransfer / priority change : test on load 3 : automatic mode inhibition 6 : product availability relay 7 : genset start / stop control : bridging bar (accessories) : auxiliary contact block - 1 NO/NC contact per position I, 0, II (accessories) Three-phase TyS p M 8 9 atysm_11_a_1_x_cat RJ RS 1 preferred source alternate source : programmable inputs : programmable outputs 7 : genset start / stop control 8 : RJ 45 for connecting a D10/D0 remote interface 9 : RS485 for communication on versions with COM : bridging bar (accessories) : auxiliary contact block - 1 NO/NC contact per position I, 0, II (accessories)

10 Characteristics according to IEC and IEC to 160 Thermal current I th at 40 C Rated insulation voltage U i (V) (power circuit) Rated impulse withstand voltage U imp (kv) (power circuit) Rated insulation voltage U i (V) (operation circuit) Rated impulse withstand voltage U imp (kv) (operation circuit) - TyS d M Rated impulse withstand voltage U imp (kv) (operation circuit) - TyS t M, g M and p M Rated operational currents I e () according to IEC Rated voltage Utilisation category / (1) / (1) / (1) / (1) / (1) / (1) 415 VC C-31 / C-31 40/40 63/63 80/80 100/ /15 100/ VC C-3 / C-3 40/40 63/63 80/80 100/ /15 100/ VC C-33 / C-33 -/40 -/63 -/80 -/100 -/15 -/15 Rated operational currents I e () according to IEC Rated voltage Utilisation category / (1) / (1) / (1) / (1) / (1) / (1) 415 VC C-0 / C-0 40/40 63/63 80/80 100/100 15/15 160/ VC C-1 / C-1 40/40 63/63 80/80 100/100 15/15 160/ VC C- / C- 40/40 63/63 80/80 100/100 15/15 160/ VC C-3 / C-3 40/40 63/63 80/80 100/100 15/15 15/ VC (5) C-1 / C-1 40/40 63/63 80/80 100/100 15/15 160/ VC (5) C- / C- 40/40 63/63 80/80 80/80 100/15 100/ VC (5) C-3 / C-3 40/40 63/63 63/63 80/80 80/80 80/80 Fuse protected short-circuit withstand (k rms prospective) Prospective short-circuit current (k rms) ssociated fuse rating () Circuit breaker protected short-circuit withstand with any circuit breaker that ensures tripping in less than 0.3s (4) Rated short-time withstand current 0.3s I cw (k rms) Short-circuit capacity (without protection) Rated short-time withstand current 1 s. I CW (k rms) Rated peak withstand current (k peak) () Connection Minimum Cu cable cross-section (mm ) Maximum Cu cable cross-section (mm ) Tightening torque (Nm) Switching time (5) I - 0 or II - 0 (ms) (3) I - II or II - I (ms) (3) Duration of "electrical blackout" I - II (ms) minimum Power supply Power supply 30 VC mini / maxi (VC) (TyS d M, t M and g M) 176/88 176/88 176/88 176/88 176/88 176/88 Power supply voltage 30 VC min / max (VC) (TyS p M) 160/ / / / / /305 Control supply power demand Nominal power (V) Max current under 30 VC () - TyS d M, t M and g M Max current under 30 VC () - TyS p M Mechanical characteristics Durability (number of operating cycles) Weight of single-phase versions - without packaging (kg) Weight of single-phase versions - with packaging (kg) Weight of three-phase versions - without packaging (kg) Weight of three-phase versions - with packaging (kg) (1) Category with index = frequent operation - Category with index = infrequent operation. () For a rated operational voltage Ue = 400 VC. (3) etween the command given and reaching of position at Un (under nominal conditions). (4) Value for coordination with any circuit breaker that ensures tripping in less than 0.3s. For coordination with specific circuit-breaker references, higher short-circuit current values are available. Please consult us. (5) t rated voltage - excluding time delays and loss of source detection time when applicable.

ATyS d M Remotely operated Transfer Switching Equipment from 40 to 160 A

ATyS d M Remotely operated Transfer Switching Equipment Transfer switches new The solution for > Applications with an external ATS/AMF controller > Building Management Systems (BMS) atys-md_002_b_1_cat