MbN Helical Gearmotors and Speed Reducers

Transcription

1 Series Helical Gearmotors and Speed Reducers Industries q Food and Beverage q Warehousing q Parcel and Package Sortation q Wastewater Treatment q Recycling Applications q Screw Conveyors q Bottling Conveyors q Unit Handling Conveyors q Material Handling Conveyors q De-Watering Conveyors D-1

2 Helical Shaft Mount Gearmotors and Speed Reducers Gearmotor C-Face Top Mount Series Input Shaft Scoop Mount D-2

3 Series Gearmotor Section... Pages D-6 - D-89 Reducer Section... Pages D-90 - D-165 Electrical Technical Data...E-1 - E-9 D-3

4 Gearmotors and Reducers Mounting Versatility and Size Range Standard Hollow Shaft Silent-Bloc/Tie Rod Frames 1-6 Max. 44,000 lb-in Gearmotors 1/3-60 HP Modular Tapered Connection Face Mount Hollow Shaft Frames 1-6 Max. 44,000 lb-in IntelliGear Gearmotor with Variable Speed 1/3-10 HP Flange Mount Hollow Shaft Frames 2-6 Max. 44,000 lb-in Series Tapered Bushed Silent-Bloc/Tie Rod Frames 2-6 Max. 44,000 lb-in Screw Conveyor Drive Frames 2-5 Max. 26,800 lb-in NEMA C-Face 56C to 326TC Backstop Options Frames C-Face Motors Frames 56C - 326TC Scoop Mount Frames to 326T High Ratio Combined Frames 2-6 All Styles Max. 44,000 lb-in Input Shaft Frames Backstop not available for gearmotors, for frame 1 c-face, or for frames 2-3 combined (i.e. more than 3 gear stages). 2 Scoop mount is not available for combined (i.e. more than 3 gear stages) frames Top mount is not available for combined units (i.e. more than 3 gear stages). Top Mount Frames to 286T D-4

5 General series and helical shaft mount gearmotors and speed reducers incorporate the latest in design and manufacturing technologies to deliver an energy efficient, reliable, helical gear train. This gearing can be combined with either a constant or variable speed motor if a gearmotor is desired. The gear frame size 1 units are available with two stages of gear reduction, whereas frame sizes 2-6 have two to five or, in some sizes, six gear stages with practical efficiencies in ratios of 4:1 to 10,000:1. The shaft mount configurations available provide an economical means of mounting the, without the need for an output coupling or chain drive and the headaches of shimming and alignment required with a foot mount arrangement. In addition to a version that can be connected to the machine frame using a tie rod or silent-bloc mount, is also available with a B14 face or B5 flange mount output. Housing All housings are cast from high-strength cast iron. This gives excellent overhung load integrity and high performance in the most demanding applications. The mounting dimensions allow the MBN to directly interchange with many popular competitive products, while retaining dimensions that also allow it to replace the MBN that it replaces. This allows for simple aftermarket replacement of both MBN and many of the more common products from other manufucturers. Additionally, the new, quill style c-face is often shorter than competitive unit designs, while allowing room for a fully rated backstop. Interchangeability The standard finished bore quill diameters and flange sizes available match those of many similar competitive units. In addition, the sizes were designed for simple replacement of the sizes that they replace. This allows for simple aftermarket replacement of both Emerson Power Transmission and many common modular helical shaft mount products from other manufacturers. Performance gearing designs deliver ratings that are amongst the highest in the industry for similar frame sizes. For replacements, this means that dimensional interchanges generally meet or exceed the original unit ratings for long life. In new applications, this can mean cost savings through downsizing versus the competition. Each unit is also supplied factoryfilled with high quality synthetic lubricant, an extra cost option for competitive units. This allows operation over a wide temperature range with minimal maintenance required. Gearmotors and Reducers General Information Flexibility The new series offers a shaft-mounted version that incorporates the unique, patented tapered bushing system from the Browning Torque Taper Plus shaft mount reducer. This extends each frame size to be usable on a variety of shaft sizes. It also provides a proven bushing system with a centering ring that reduces wobbling on the shaft for reduced wear and tear. Where an output flange is used for mounting, frame sizes 2-4 have two flange sizes available per gear frame. This makes the very adaptable compared to other brands. For applications requiring the gearmotors to be powered by an inverter (VFD), all three phase motor designs now incorporate an upgraded wire and varnish treatment called Allguard. Housings can be mounted in a variety of positions as well, with only a change in the breather and drain plug positions and a change in oil volume. Gearmotors The industry s most diverse array of different motor constructions and voltages in three and single phase are stocked to meet most industry and user specifications. This now includes IntelliGear variable speed TEFC gearmotors that incorporate a rugged, compact, pre-programmed AC variable frequency drive onboard for simple 6:1, 10:1, or 15:1 constant torque speed ranges. Emerson Power Transmission exclusive offerings are the inverter duty gearmotors that are fully compliant with NEMA MG1 Part 31 and the explosion proof gearmotors. Screw Conveyor Drives The units may be ordered in a CEMA screw conveyor drive version. The same variety of screw conveyor drive shafts, sealing cartridges, and trough ends are available as the Browning Torque Taper Plus shaft mount product line. Now there s a screw conveyor drive available with a full range of gear ratios and a gearmotor, c-face, input shaft, scoop mount or top mount input. Additionally, the exclusive explosion proof gearmotor offering makes for a lower cost, more compact alternative in applications such as grain handling. Reliability Gear housings are fitted with normally closed breathers to help exclude contaminants, while preserving low internal operating pressure. All oil seals operate on plunge ground shaft surfaces to deliver extended life. Enhanced insulating materials and other standard features of our premium Varidyne inverter duty motors allow Emerson Power Transmission to extend an industry leading 3-year motor warranty, even when using these motors with PWM inverter power up to 575 VAC. D-5 Series

6 Table of Contents Gearmotors Series Section Page Design Features...D-7 Mounting Versatility and Size Range...D-8 Motor Options...D-9 Gearmotor Selection (constant speed)...d-10 - D-11 Gearmotor Selection (variable speed)...d-12 - D-13 Catalog Nomenclature...D-14 - D-15 Gearmotor Mounting Configuration...D-16 Gearmotor Mounting Positions...D-16 Electrical Connection Options...D-17 Tapered Bushing Selections...D-18 - D-19 Screw Conveyor Accessories...D-20 - D-21 Mounting Accessories (Silent-Bloc and Tie Rod)...D-22 Modifications, Options and Accessories...D-23 - D-25 AGMA Application Classifications...D-26 - D-28 Gearmotor Selection Tables...D-29 - D-67 Dimension Prints with Standard TEFC Motors 00C Finished Bore Shaft Mount...D-68 - D-73 40C Finished Bore Face Mount...D-68 - D-73 50C/60C Finished Bore Flange Mount...D-74 - D-78 00B Tapered Bushed Shaft Mount...D-79 - D-83 00S Screw Conveyor Drive...D-84 - D-85 Alternate Motor End Dimensions...D-86 - D-87 Brake Dimensional Supplement...D-88 Gearmotor Weights...D-89 Lubrication...D-164 Hollow Shaft Details...D-165 Gearmotor - Typical Motor Performance Data...E-1 - E-4 IntelliGear Technical Specifications...E-5 - E-9 NEMA Standard Dimensions...E-10 General Information...E-11 Standard Terms and Conditions of Sale...E-12 D-6

7 Series Gearmotor Features Design Features 1. Innovative Self-Locking, Self-Aligning Taper Shaft Motor Connection Easy on-site motor replacement Change motor without draining oil, breaking the gearcase seal, or changing primary pinion. Eliminates fretting, precision alignment, and solid connection for indexing. 2. Gearcase Supplied Factory Filled with Synthetic Oil Wide temperature range and longer life. 3. Tapered Bushed Version Available on Gear Frame Sizes 2-6 Each frame available with a variety of bushing bore diameters. Frames 2-5 utilize a unique patented reversible single bushing system with a stabilizing ring to minimize wobble for reduced wear and tear. It includes an end cap to seal the quill end from contamination. 4. Corrosion and Shock Resistant Cast Iron Housing Reinforced and ribbed for extra strength. 5. Helical Gears and Shafts of Nickel Chromium Molybdenum Steel Helical gearing is case hardened and then skived, superfinished, or ground. Helical gears heat shrunk on shafts or mounted on self-locking tapered shafts and keyed for high shock load capability. 6. Normally Closed Breather with Multiple Locations 7. Double Lip Seals on Heat Treated, Plunge Ground Shafts 8. Magnetic Drain Plug Standard 8 D-7 Series

8 Gearmotors Mounting Versatility and Size Range Standard Hollow Shaft Silent-Bloc/Tie Rod Frames 1-6 Max. 44,000 lb-in Three Phase TEFC 1/3 60 HP Face Mount Hollow Shaft Frames 1-6 Max. 44,000 lb-in Corro-Duty 1/3 60 HP Flange Mount Hollow Shaft Frames 2-6 Max. 44,000 lb-in Single Phase TEFC 1/3 5 HP Series Tapered Bushed Silent-Bloc/Tie Rod Frames 2-6 Max. 44,000 lb-in Screw Conveyor Drive Frames 2-5 Max. 26,800 lb-in High Ratio Combined Frames 2-6 All Styles Max. 44,000 lb-in Modular Tapered Connection Explosion Proof 1/3 50 HP Brakemotor 1/3 10 HP D-8 IntelliGear Motor with VFD 1/3 10 HP

9 Gearmotors Motor Options TEFC Three Phase Suitable for general purpose industrial applications Energy efficient design standard 1.25 service factor through 30 HP; 1.15 service factor above 30 HP Suitable for 50 Hz, 190/380 VAC through 30 HP Premium class F Allguard insulation standard 40 C ambient, NEMA B design, continuous duty Premium efficiency available Inverter duty option per NEMA MG1 part 31 stocked Corro-Duty Designed for wet, corrosive applications and industries including waste treatment, mining and lumber. All cast iron construction (56 and 140 frames are rolled steel) Premium efficiency standard 3 HP and above 1.15 service factor, class F Allguard insulation Condensation drains in motor and conduit box 40 C ambient, NEMA design B, continuous duty Inverter duty version per NEMA MG1 Part 31 stocked to 20 HP TEFC Single Phase For agricultural, light material handling, textile, and light pumping applications 1.25 service factor (1.15 service factor, 1 HP, 48 frame) (1.0 service factor, 2 HP and 1.15 service factor, 3-5 HP) Capacitor start (capacitor run above 1/2 HP, 48 frame) (capacitor run above 1/2 HP, T frames) Class B insulation, continuous duty, reversible Explosionproof Ideal for the petro-chemical, grain, mining, and chemical industries Class I, group D, class II, groups F and G All cast iron construction (plastic fan cover) 1.0 service factor, class B insulation 40 C ambient, NEMA B design, continuous duty UL approved Inverter duty per NEMA MG1 part 31 available IntelliGear Variable speed gearmotor with NEMA 4/12 enclosure "Onboard" pushbutton and remote speed changing options Pre-programmed 6:1 constant torque speed range Versions for 3/460V input power supplies from 1/3 to 10 HP 1/230V to 2 HP and 3/230V to 5 HP 1/115 V through 3/4 HP UL, CUL and CE Optional 10:1 and 15:1 speed ranges Series D-9

10 Selection Information Constant Speed Gearmotor Selection Size Selection 1. Input HP Based on application data 2. Speed / ratio Obtain either desired output speed (rpm) or gearbox ratio based on application. 3. Mechanical service factors - gears There are three standard classifications for gearmotor applications: Class I - uniform loading, 3-10 hours per day, service factor 1.0 (minimum). Class II - uniform loading over 10 hours per day or moderate shock loading up to 10 hours per day; service factor 1.4 (minimum). Step 1 - Locate gearmotor selection tables (pages D-29 - D-67) based on motor HP. Step 2 - Choose the appropriate nominal speed or ratio required. Step 3 - Select the correct gearmotor based on AGMA class or service factor determined from selection information. Step 4 - If the tapered bushed design is selected, choose the appropriate bushing from pages D-18 and D-19. Torque and HP Calculations The output torque available from an gearmotor can be calculated from the following formula: Series Class III - moderate shock loading over 10 hours per day or heavy shock loading up to 10 hours per day; service factor 2.0 (minimum). The tables on pages D-26 through D-28 are based on past operating experience within the industries listed and information gathered by AGMA. If the user has data reflecting greater severity than normal industry usage, then the AGMA class should be increased. Choose the AGMA class for your given application based on this criteria. If your application cannot be found, use the following table to determine the service factor. Duty Cycle Continuous Frequent Starts/ Stops* Hours Operation *Greater than 10 per hour Uniform Load U Moderate Shock Load M Heavy Shock Load V Output Torque T (lb-in) = Motor HP x x Gear Efficiency Output rpm or Output Torque T (lb-in) = Motor HP x x Gear Efficiency x Gear Ratio Motor rpm If the output torque required by the load is known, the input HP that will produce that amount of torque can be calculated as follows: Input HP = Output Torque Required (lb.-in.) x Output rpm x Gear Efficiency or Input HP = Output Torque Required (lb.-in.) x Motor rpm x Gear Efficiency x Gear Ratio D-10

11 Constant Speed Gearmotor Selection Selection Example A shaft mounted gearmotor is required to operate a uniformly loaded belt conveyor at 56 rpm, 24 hours per day. The customer has specified a standard 230/460 VAC, 3-phase, TEFC gearmotor rated 5 HP. The unit will be mounted on a 1.75" diameter shaft using a tapered bushed output, with a tie rod type torque arm bolted to the machine to prevent rotation. The unit will be in the normal position with the motor and output shaft horizontal and the input directly above the output. 1. Input HP is 5 HP 2. Output Speed required is 56 rpm AGMA service classification table on page D-26 indicates the following: Application Load Class Conveyors Uniformly Loaded or Fed: Apron, Assembly, Belt, Up to 10 Hrs/Day Over 10 Hrs/Day Bucket, Chain, Flight, Oven, Screw U I II Since this application operates 24 hours per day, a Class II service factor is required. Step 1... Locate a gearmotor for 5 HP on page D-53. Step 2... Find a nominal speed closest to the 56 rpm output required. Step 3... Select the row in the table for Class II service factor. Output AGMA Service Output Torque Nominal Frame Size Std. Motor RPM Class Factor in-lb Ratio Gear Motor Types 56 I T T,S,C,X,IG 56 I, II, III T T,S,C,X,IG Note that there are two lines for 56 rpm, however only the second line meets the minimum Class II service factor requirement. The 56 rpm line with the size 3472 gearmotor is the proper selection. This means that the Size 3472 gear frame with 31.5:1 nominal ratio and 56 rpm output is the best selection. Step 4... Select the appropriate bushing from pages D-18 and D-19 for the customer s 1.75" diameter shaft. For gear frame 3472 and 1.75" diameter, the bushing part number is 207TBP112. Complete the Process by Building a Complete Part Number Catalog designation (see Catalog Nomenclature page D-14): B P MT 184T 5 Torque Arm: MUB999TA002 Series The codes indicate the following: Frame 3472 gearmotor, 00 = the standard housing with no faces or flanges, B = tapered bushed output shaft, P3 = the normal mounting position with output shaft horizontal and motor directly above output shaft, 31.5:1 nominal ratio, MT = standard TEFC motor, 184T motor frame, 5 HP. (Page D-16 explains output shaft, face or flange and mounting positions. Page D-15 shows motor types. The torque arms are shown on page D-22.) D-11

12 Selection Information IntelliGear Gearmotor Selection Size Selection 1. Determine installation environment Control enclosure is NEMA 4/12 2. Input HP For constant torque loads this is at maximum speed of range. Therefore, the gear ratio should be selected to closely match the required maximum speed. 3. Speed range Confirm maximum and mininum of needed range. 4. Determine control power supply Phase and voltage Power Supply Input HP's 1 ph / 115 v.33 to.75 1 ph / 230 v.33 to 2 3 ph / 230 v.33 to 5 3 ph / 460 v.33 to 10 3 ph / special R. O. Step 1 - Determine the maximum motor rpm from the following table based on the whether the application requires a speed range of 6:1, 10:1 or 15:1. HP Speed Range = Maximum Output Speed Required Minimum Output Speed Required 6:1 Speed Range IntelliGear Motor Speed Range 10:1 Speed Range 15:1 Speed Range 1/3-3/4 HP rpm rpm rpm 1-1 1/2 HP rpm rpm rpm 2 HP rpm rpm N. A. 3 HP rpm rpm N. A. 5 HP rpm rpm N. A. 7.5 HP rpm rpm N. A. 10 HP rpm rpm N. A. Series 5. Mechanical service factoring of gear Refer to page D-10 for this procedure. Note: IntelliGear application for 1 phase power supply is limited to 10 starts per hour where the unit is started via AC power mains contactor. 6. Determine speed adjustment option (see pages E-8 - E-9) Select from: PD = Digital keypad with forward/reverse/stop/ speed up/speed down/speed display on IntelliGear enclosure P1 = Run/stop/speed pot. mounted on IntelliGear enclosure P2 = Forward/reverse/stop/pot. mounted on IntelliGear enclosure P3 - Speed pot. (only) mounted on IntelliGear enclosure (start/stop by others) P4 = Speed pot. (only) mounted inside IntelliGear enclosure (start/stop by others) R = Remote signal following (0-10VDC or 4-20mA supplied by others) RP = Remote from fieldbus - Profibus DP Step 2 - Determine the gear ratio required. Use the maximum motor rpm from the table above. Gear Ratio = Maximum Motor Speed Maximum Output Speed Req d. Step 3 - Locate gearmotor selection tables based on the input HP required at the ratio calculated in Step 2. Select the nominal gear ratio closest to the one calculated. Step 4 - Select the correct gearmotor that meets or exceeds the AGMA class or service factor determined in the selection information. Step 5 - If the tapered bushed design is selected, choose the appropriate bushing from pages D-18 and D-19. Step 6 - Confirm input power supply is compatible with HP of selection and select the speed adjustment option desired for the application. Step 7 - Referring to page D-17, determine if an alternative controller location is required for the application. (Note that the default location is FO the 12 o clock position.) D-12

13 IntelliGear Gearmotor Selection Selection Example A shaft mounted gearmotor is required to directly operate a uniformly loaded assembly line conveyor. The equipment operates 16 hours per day, and the required speed range is 4 to 37 rpm. The customer prefers a bushed connection to prevent fretting, and the shaft is 1 7/8" in diameter. The customer has specified a 2 HP gearmotor with a standard TEFC motor, and the power supply is 460 VAC, 3-phase. A silent bloc mount will be used to attach the gearmotor to the machine frame and prevent rotation. The unit will be mounted on its side with the motor and output shaft horizontal. Viewed from the motor fan, the motor will be mounted to the right of the output shaft. 1. Input HP is 2 HP 2. Output speed range required is 4-37 rpm 3. AGMA service classification table on page D-26 indicates the following: Application Load Class Assembly Conveyors Uniformly Loaded or Fed Heavy Duty U M Up to 10 Hrs/Day Since this conveyor is uniformly loaded and operates 16 hours per day, a Class II service factor is required. I II Over 10 Hrs/Day II II Step 1... Calculate the speed range required: 37 rpm Max/4 rpm Min = 9.25:1, so an IntelliGear with 10:1 range is required. This means the motor top speed will be 2585 rpm for a 2 HP IntelliGear. Step 2... The ideal gear ratio is 2585 RPM/37 RPM = 69.9:1. Step 3... Locate the gearmotor selection table for 2 HP on page D-45, and find a nominal ratio close to 69.9:1. Step 4... Select the row in the table for Class II service factor. Output AGMA Service Output Torque Nominal Frame Size Std. Motor RPM Class Factor in-lb Ratio Gear Motor Types 26 I, II, III T T,S,C,X,IG 25 I, II T T,S,C,X,IG Note that 71:1 ratio is closest nominal ratio to 69.9:1. There are two choices at this ratio, and the best is Gear Frame 3363, which is the smallest frame size that meets the Class II service factor requirement. Step 5... Select the appropriate bushing from pages D-18 and D-19 for the customer s 1 7/8" diameter shaft. For gear frame 3363 and 1 7/8" diameter, the bushing part number is 115TBP114. Step 6... The power supply is 460 VAC/3-phase, and there is an IntelliGear available for this voltage at 2 HP. (See the footnote at the bottom of page D-45.) Complete the Process by Building a Complete Part Number Catalog designation (see Catalog Nomenclature page D-14): Series B P7 71 T4 145T 2 Silent Bloc: MUB230AM001 The codes indicate the following: Frame 3363 gearmotor, 00 = the standard housing with no faces or flanges, B = tapered bushed output shaft, P7 = mounting position turned on the side with output shaft horizontal and the motor to the right of the output shaft (viewed from motor fan end), 71:1 nominal ratio, T4 = 460 VAC IntelliGear motor with VFD, 145T motor frame, 2 HP. (Page D-16 explains output shaft, face or flange and mounting positions, and page D-15 shows motor types. The silent bloc bushings are shown on page D-22.) D-13

14 Ordering C P MT 145T 1.5 M11 See page D-16 Browning Helical Shaft Mount Series Series Series Reducer Size Stages = 2 stages = 3 stages or 4A = 4 stages combined Output Face/Flange & Shaft Configuration Mounting Position Nominal Gear Ratio 00C = Straight Hollow Bore with No Face or Flange 1 P = 22.4:1 40C = Straight Hollow Bore wth B14 Face Mount 50C = Straight Hollow Bore with B5 Flange Mount 2 5 or 5A = 5 60C = Straight Hollow Bore with stages combined Alternate B5 Flange Mount 2 6 or 6A = 6 00B = Tapered Bushed Output stages combined with No Face or Flange Mount 2 00S = CEMA Screw Conveyor Drive Output 2 P6 P7 P8 PV5 PV6 Use Nominal Ratio Selected from Gearmotor Selection Tables Input Type Motor Type Selected from Catalog Designation Column in Standard Motor Input Types Table on page D-15 Motor Frame Motor HP Modifications T 1.5=1.5 HP 1/3-60 HP Select from Available Modifications Listed on Pages D-23 - D C is only available for Series. ² Not available in frame 31. Series Motor Frame T 145T 145TY Gear Frame / Gearmotors 182T 213T 184T 215T Range of Ratios Available :1, 9:1-71:1 7.1:1, 9:1-71:1 7.1:1, 9:1-71:1 7.1:1, 9:1-18:1 3242/3202 4:1-35.5:1 4:1-35.5:1 4:1-31.5:1 4:1-20:1 3243/ :1-224:1 40:1-224:1 40:1-140:1 3244/3245/ :1-10,000:1 250:1-10,000: :1-56:1 5.6:1-56:1 5.6:1-56:1 5.6:1-35.5:1 5.6:1-35.5: :1-315:1 63:1-315:1 63:1-280:1 63:1-180:1 3364/ :1-10,000:1 355:1-10,000: :1, 8:1-50:1 5:1, 8:1-50:1 5:1, 8:1-50:1 5:1, 8:1-50:1 5:1-40:1 5:1-18: :1-250:1 56:1-250:1 56:1-250:1 56:1-160:1 56:1-160: :1-1,600:1 250:1-1,600:1 250:1-1,600:1 250:1-1,000: ,800:1-7,100:1 1,800:1-7,100:1 1,800:1-7,100:1 1,800:1-4,500: ,000:1-10,000:1 8,000:1-10,000:1 8,000:1-10,000:1 8,000:1-10,000: :1-31.5:1 9:1-31.5:1 9:1-31.5:1 9:1-31.5:1 5:1-31.5:1 5:1-20:1 5:1-20: :1-224:1 63:1-224:1 63:1-224:1 63:1-224:1 35.5:1-224:1 35.5:1-140:1 35.5:1-140:1 3584/ :1-2,800:1 250:1-2,800:1 250:1-2,800:1 250:1-1,600: ,150:1-10,000:1 3,150:1-10,000:1 3,150:1-10,000:1 3,150:1-8,000: :1-35.5:1 12.5:1-35.5:1 7.1:1-35.5:1 7.1:1-20:1 7.1:1-20: :1-200:1 20:1-200:1 20:1-140:1 20:1-140:1 2604A 224:1-1000:1 224:1-1000:1 224:1-1000:1 224:1-630:1 224:1-630:1 2605A 900:1-4,000:1 900:1-4,000:1 900:1-4,000:1 900:1-2,500:1 900:1-2,500:1 2606A 3,550:1-10,000:1 3,550:1-10,000:1 3,550:1-10,000:1 3,550:1-10,000:1 3,550:1-10,000:1 254T 256T 284T 286T 324T 326T 364T 368T Flange Dimensions (mm) BD AK AJ Gear Frame Output Flange Part Number Designator 31 Flange Not Available 32 60C 50C 33 60C 50C 34 60C 50C 35 50C 26 50C D-14

15 MOTOR TYPE SPEED - DESIGN Ordering Standard Motor Input Types CATALOG MOTOR DESCRIPTION (NOT REQUIRED) DESIGNATION FRAME (S) VOLTAGE POLES S MR TY 115/230 4 Single Single Phase TEFC MR2 184T MT T /460 4 M T 190/380 4 Single MB 324T - 365T 230/460 4 Standard Efficiency MV T MO T 230/460 6 MW T Single MY** 143T - 365T 230/460 4 T High Efficiency MZ** 143T - 365T Three Phase TEFC Inverter Duty Two Speed (Constant Torque) Single High Efficiency FCR DC Brake Single Standard Efficiency MI** T 230/460 4 MD** T U T 230 4/8-1 Winding U T 460 4/8-1 Winding U T 575 4/8-1 Winding MTB T 230/460 4 MVB T MC** TY 230/460 4 C T 190/380 4 MG** TY MF T 230/460 6 C MC** 143T - 365T 230/460 4 Single High Efficiency Corro-Duty MG** 143T - 365T Three Phase Two Speed (Constant Torque) Inverter Duty Single C T 230 4/8-1 Winding C T 460 4/8-1 Winding C T 575 4/8-1 Winding CI** T 230/460 4 CD** T MX T 230/460 4 ME T Z T 230/460 6 X X T 230 4/8-1 Winding Explosion Proof Two Speed (Constant Torque) X T 460 4/8-1 Winding X T 575 4/8-1 Winding IG Inverter Duty XI T 230/460 4 XD T TS1 56 1/115* 4 IntelliGear 6:1 Range *** (Constant TS TY 1/230* 4 TEFC/NEMA 4/12 Torque) Variable Speed T T 3/230* 4 (Motor/Controller) T T 3/460* 4 * Controller input power. Controller output is 3 phase. ** To get the FCR Integral, DC Coil Brake, add "B" to the catalog designation (available 1/3-2HP). e.g. change "MI" to "MIB". *** 10:1 and 15:1 constant torque speed ranges are also available. D-15 Series

16 Gearmotors Mounting Positions Mounting Configuration Face Mount Hollow Shaft Flange Mount Hollow Shaft Tapered Bushed Screw Conveyor Drive 40C 50C/60C 00B 00S Availability Gear Frame 40C 50C 60C 00B 00S 31 l l l l l l 33 l l l l l 34 l l l l l 35 l l - l l 26 l l - l - l Normally Stocked, - Not Available Mounting Positions Series P3 P6 P7 P8 PV5 PV6 D-16

17 Conduit Box Location Gearmotors Electrical Connection Options F0 When ordering a conventional gearmotor, specify the desired conduit box location viewing the motor fan end in the P3 mounting position. If no option is specified, the F1 position will be supplied. F2 FX F1 (Standard) Conduit Box F0 (Standard) Controller Location When ordering an IntelliGear gearmotor, the controller location may be specified viewing the motor fan end in the P3 mounting position. If no options are specified, the F0 position will be supplied. F2 F1 Cable Entry A (Standard) IntelliGear Controller B IntelliGear cable entry can be from either side of the IntelliGear enclosure as viewed from the motor fan end. Position B may be specified upon order entry, but position A is supplied if neither position is specified. Cable Entry 12 o'clock Series FCR DC Brake Manual Release Lever Location Unit Type Default Location Optional Locations less IntelliGear 12 o'clock 3, 6, or 9 o'clock 9 o'clock 3 o'clock with IntelliGear 9 o'clock 3, 6, or 12 o'clock (lever cannot be in same position as IntelliGear) 6 o'clock Brake Lever Location D-17

18 32-35 and 26 units can be ordered with a 00B bushed output version. When a bore size is defined at order entry, this configuration includes the appropriate bushing kit unassembled. The table below shows the available stocked bushing bores that may be specified for each frame size. Each bushing kit is supplied with the bushing, mounting hardware, and a stabilizer ring (except 26 which has no stabilizer ring). Where a bushing is needed for a spare or for a bore size change, select it from the following table by gear frame size unique, patented single bushing mounting system - Mounts from either side - Tapered stabilizer ring minimizes wobble - End cap seals quill end from contamination - Resists fretting corrosion Tapered Bushings Stabilizer Ring Series Frame Meas. Unit Inch Bushing No. Bore Shaft Keyseat Required Type Stabilizer Ring Width Size Bolt Torque (Ft-Lbs) Weight (Lbs) 107TBP012 3/4 3/16 x 3/32 x 3 7/ TBP014 7/8 3/16 x 3/32 x 3 7/ TBP015 15/16 1/4 x 1/8 x 3 7/ TBP /4 x 1/8 x 3 7/ TBP /16 1/4 x 1/8 x 3 7/ TBP /8 1/4 x 1/8 x 3 7/ TBP /16 1/4 x 1/8 x 3 7/ /16-18 x 1 1/ TBP /4 1/4 x 1/8 x 3 7/ TBP /16 5/16 x 5/32 x 3 7/ TBP /8 5/16 x 5/32 x 3 7/ TBP /16 3/8 x 3/16 x 3 7/ TBP30MM 30 mm 8 x 4 x 94 (mm) Metric 1 107TBP35MM 35 mm 10 x 5 x 94 (mm) TBP015 15/16 1/4 x 1/8 x 4 1/ TBP /4 x 1/8 x 4 1/ TBP /16 1/4 x 1/8 x 4 1/ TBP /8 1/4 x 1/8 x 4 1/ TBP /16 1/4 x 1/8 x 4 1/ Inch 115TBP /4 1/4 x 1/8 x 4 1/ TBP /16 5/16 x 5/32 x 4 1/ TBP /8 5/16 x 5/32 x 4 1/ TBP /16 3/8 x 3/16 x 4 1/ /8-16 x 1 1/ TBP /2 3/8 x 3/16 x 4 1/ TBP /8 3/8 x 3/16 x 4 1/ TBP /16 3/8 x 3/16 x 4 1/ TBP /4 3/8 x 3/16 x 4 1/ TBP /8 1/2 x 1/4 x 4 1/ TBP /16 1/2 x 1/4 x 4 1/ Metric 1 115TBP40MM 40 mm 12 x 5 x 100 (mm) TBP45MM 45 mm 14 x 5.5 x 100 (mm) Metric bushings have metric bores and require metric keyseats as shown in mm. D-18

19 Tapered Bushings Driven Shaft Key (Furnished) Type 3 Frame 34 Meas. Unit Inch Bushing No. Bore Shaft Keyseat Required Type Stabilizer Ring Width Size Bolt Torque (Ft-Lbs) Weight (Lbs) 207TBP /8 5/16 X 5/32 x 5 1/ TBP /16 3/8 X 3/16 X 5 1/ TBP /2 3/8 X 3/16 X 5 1/ TBP /8 3/8 X 3/16 X 5 1/ TBP /16 3/8 X 3/16 X 5 1/ TBP /4 3/8 X 3/16 X 5 1/ TBP /8 1/2 X 1/4 X 5 1/ TBP /16 1/2 X 1/4 X 5 1/ /8-16 X 1 1/ TBP /2 X 1/4 X 5 1/ TBP /8 1/2 X 1/4 X 5 1/ TBP /16 1/2 X 1/4 X 5 1/ TBP /4 1/2 X 1/4 X 5 1/ TBP /16 5/8 X 5/16 X 5 1/ TBP50MM 50 mm 14 x 5.5 x 125 (mm) Metric 1 207TBP60MM 60 mm 18 x 7 x 125 (mm) TBP /16 3/8 X 3/16 X 5 5/ TBP /2 3/8 X 3/16 X 5 5/ TBP /16 3/8 X 3/16 X 5 5/ TBP /4 3/8 X 3/16 X 5 5/ Inch 26 Inch 215TBP /8 1/2 X 1/4 X 5 5/ TBP /16 1/2 X 1/4 X 5 5/ TBP /2 X 1/4 X 5 5/ TBP /16 1/2 X 1/4 X 5 5/8 2 3/8-16 X 1 3/ TBP /4 1/2 X 1/4 X 5 5/ TBP /16 5/8 X 5/16 X 5 5/ TBP /2 5/8 X 5/16 X 5 5/ TBP /16 5/8 X 5/16 X 5 5/ TBP /16 3/4 x 3/8 x 5 5/ Metric 1 215TBP60MM 60 mm 18 x 7 x 172 (mm) 2 NA /16 5/8 X 5/16 X /2 5/8 X 5/16 X /16 3/4 x 3/8 x /8 3/4 x 3/8 x NA /16 3/4 x 3/8 x /16 3/4 x 3/8 x /16 7/8 x 7/16 x Metric bushings have metric bores and require metric keyseats as shown in mm. Series D-19

20 Screw Conveyor Drive Shafts 2 2 Complete the shaft part number by adding shaft type as follows: Screw Conveyor Drives Standard 2 hole steel shaft = leave blank (example 107DSP108) Optional 3 hole steel shaft = add -3 (example 107DSP108-3) 2 hole stainless steel shaft = add SS (example 107DSP108SS) 3 hole stainless steel shaft = add -3SS (example 107DSP108-3SS) Gear Frame 1 1/2 Dia. Shaft for 6 & 9 Dia. Screw 2 Dia. Shaft for 9 & 12 Dia. Screw 2 7/16 Dia. Shaft for 12 & 14 Dia. Screw 3 Dia. Shaft for Dia. Screw 3 7/16 Dia. Shaft for Dia. Screw 31 Not Available DSP DSP DSP DSP300 N/A DSP DSP DSP DSP300 N/A 34 N/A 207DSP DSP DSP DSP N/A 215DSP DSP DSP DSP Not Available Screw Conveyor Accessories Gear Frame Optional Seal Cartridges Felt Seal 1 Waste Pack Kit Packing Gland Kit 31 Not Available WPP 107PGP FR WPP PGP FR WPP PGP FR WPP PGP FR Not Available 1 Felt seal can only be added to the waste pack seal cartridge kit. Screw Conveyor Drives May Be Assembled in the Field Required Components Include: 00S gearmotor with screw conveyor adapter Screw conveyor drive shaft Series Optional Components Include: Waste pack Packing gland Felt seal Waste Pack Kit Felt Seal Screw Conveyor Adapter (Included with type 00S gear unit) Packing Gland Kit Screw Conveyor Drive Shaft Kit Screw Conveyor Thrust Ratings Output tapered roller bearing standard - all sizes. D-20 Gear Frame Maximum Thrust Rating (Lbs.)

21 Screw Conveyor Trough Ends Table No. 33 Formed Hot Roll Plate Steel Specifications Part No. Conveyor Drive Shaft Dimensions Fig. Type Screw Dia. Dia. A B C D E F G H J K L SCTE06 x 1 1/2" 6" 1 1/2" 1 6-Hole 10 1/8" 4 1/2" 1 1/2" 1 3/4" 1" 9 3/4" 4 7/8" 1 3/4" 9/16" 2" 8 1/8" SCTE09 x 1 1/2" 9 1 1/2 2 8-Hole /8 1 5/8 2 5/8 1 1/2 13 3/4 6 7/8 1 3/4 9/ /8 SCTE09 x Hole /8 1 5/8 2 5/8 1 1/2 13 3/4 6 7/8 2 1/4 11/16 2 9/16 9 3/8 SCTE10 x 1 1/ /2 2 8-Hole 15 1/4 6 3/8 2 3/8 2 7/8 1 3/4 14 3/4 7 3/8 1 3/4 9/ /2 SCTE10 x Hole 15 1/4 6 3/8 2 7/8 2 7/8 1 3/4 14 3/4 7 3/8 2 1/4 11/16 2 9/16 9 1/2 SCTE12 x Hole 17 3/8 7 3/ /4 1 5/8 17 1/4 8 5/8 2 1/4 11/16 2 9/ /4 SCTE12 x 2 7/ / Hole 17 3/8 7 3/ /4 1 5/8 17 1/4 8 5/8 2 11/16 11/ / /4 SCTE12 x Hole 17 3/8 7 3/ /4 1 5/8 17 1/4 8 5/8 3 1/4 13/ /4 SCTE14 x 2 7/ / Hole 20 1/8 9 1/ /8 1 5/8 19 1/4 9 5/8 2 11/16 11/16 2 3/ /2 SCTE14 x Hole 20 1/8 9 1/ /8 1 5/8 19 1/4 9 5/8 3 1/4 13/ /2 SCTE16 x Hole 22 5/8 10 5/8 2 1/2 3 1/ /4 10 5/8 3 1/4 13/ /8 SCTE18 x Hole 25 1/2 12 1/8 2 1/2 3 1/ /4 12 1/8 3 1/4 13/ SCTE18 x 3 7/ / Hole 25 1/2 12 1/8 2 1/2 3 1/ /4 12 1/8 3 11/16 13/16 3 3/8 16 SCTE20 x Hole 28 1/2 13 1/2 2 1/2 3 3/4 2 1/4 26 1/4 13 1/8 3 1/4 13/ /4 SCTE20 x 3 7/ / Hole 28 1/2 13 1/2 2 1/2 3 3/4 2 1/4 26 1/4 13 1/8 3 11/16 13/16 3 3/8 19 1/4 SCTE24 x 3 7/ / Hole 34 5/8 16 1/2 2 1/2 4 1/8 2 1/2 30 1/4 15 1/8 3 11/16 13/16 3 3/8 20 Part No. Dimensions M N P Q R S T U V W X Y Z AB Wt. Lbs. SCTE06 x 1 1/2" 4 1/16 4 7/ /32 5/8 3 15/16 2 1/32 3/16 7/ / / SCTE09 x 1 1/2" 4 11/16 6 1/4 4 15/16 13/ / /64 1/4 7/ /64 2 9/ / SCTE09 x /16 6 1/4 4 15/16 13/ / /64 1/4 7/ /64 2 9/ / SCTE10 x 1 1/2 4 3/4 6 5/8 4 1/8 5/8 3 3/8 6 1/8 1/4 7/ / / / SCTE10 x 2 4 3/4 6 5/8 4 1/8 5/8 3 3/8 6 1/8 1/4 7/ / / / SCTE12 x 2 6 1/8 7 15/16 6 1/4 15/16 4 7/ /64 5/16 9/ /64 3 7/ / SCTE12 x 2 7/16 6 1/8 7 15/16 6 1/4 15/16 4 7/ /64 5/16 9/ /64 3 7/ / SCTE12 x 3 6 1/8 7 15/16 6 1/4 15/16 4 7/ /64 5/16 9/ /64 3 7/ / SCTE14 x 2 7/16 6 3/4 8 15/ /32 1 3/ / /64 5/16 9/ / / SCTE14 x 3 6 3/4 8 15/ /32 1 3/ / /64 5/16 9/ / / SCTE16 x 3 7 7/ /8 4 57/ /64 5/16 11/ /32 3 3/ / SCTE18 x /2 3 9/ / /64 5/16 11/ / / / /16 11/ SCTE18 x 3 7/ /2 3 9/ / /64 5/16 11/ / / / /16 11/ SCTE20 x 3 9 5/8 12 3/ / / /64 8 3/16 3/8 11/ / /64 9 1/ /32 13/ SCTE20 x 3 7/16 9 5/8 12 3/ / / /64 8 3/16 3/8 11/ / /64 9 1/ /32 13/ SCTE24 x 3 7/ / / /32 31/ /64 3/8 11/ / / /8 9 7/32 13/16 3 5/ Notes: Browning Trough Ends are drilled to fit CEMA standard troughs. The center holes are drilled to fit Browning Screw Conveyor Drives. s Figure 4 has 2 Z holes in bottom flange only; no holes in top flange. D-21 Series

22 Gearmotors Modifications, Options and Accessories Mounting Accessories Standard Mounting By Reaction Point The use of "Silent-Bloc" is recommended for standard mounting of OOC and OOB style units, or 40C units not utilizing "face" for mounting. These resilient rubber bushings help to minimize vibration. Order by part number below. Silent-Bloc Option Gear Frame Silent-Bloc Kit # ID x OD x Thickness MUB230AM x 1.57 x MUB450AM x 2.36 x MUB600AM x 3.15 x 1.20 Optional Mounting with Tie Rod A conventional tie rod kit is available as shown in the diagram below. It is used to secure the 00C or 00B style housing to a solid machine surface and prevent rotation of the gear unit. Tie rod can be used with 40C units not utilizing "face" for mounting. Order by the part number in the table below: G F E B C D A Series Note: Tie rod may be mounted on the opposite side if desired. Dimensions (Inches) Gear Frame Tie Rod Kit # A B C D E F MIN. MAX. G MUB999TA MUB999TA MUB999TA Note: Tie rod assemblies should always be mounted in tension. D-22

23 Inverter Duty Gearmotors Improvements in helical shaft mount designs begin with three phase motor designs that now incorporate an upgraded wire and varnish treatment called Allguard. This makes the standard three phase gearmotors suitable for use with inverters in many applications. A one year warranty will be extended for 3:1 (60-20 Hz) constant torque for standard efficiency design motors and 4:1 (60-15 Hz) constant torque for premium efficiency design motors providing the following conditions are met: Motor is non-hazardous 3 phase > 48 frame Cable length to controller 100 ft Line voltage is 480 VAC Thermal protection is not required For all other conditions of operation, including up to 575 VAC and for hazardous location service, select a Varidyne inverter duty motor design. These designs include thermostats in winding, a 3 year warranty on the motor and full compliance with NEMA MG1 Part 31. M1 Brakes Motor Modifications *Indicates borderline maximum rating for holding loads only. Gearmotors Modifications, Options and Accessories Design These brakes are motor mounted having a direct acting, spring set, electromagnetically released disc design. When power to the brake is interrupted, the brake will set and hold. When power is restored, the brake will automatically release. Table 1 gives the brake torque for stopping and holding loads not greater than the full load motor torque. Refer applications involving high inertia loads or with frequent starts and stops to Application Engineering for review. Table 1 Max. HP Ratings - High Speed Input 4 Pole 4 Pole 6 Pole 6 Pole RPM RPM RPM RPM Brake Torque (Ft- Lbs) 1 3/4 1/2 1/ / /2* / * 7 1/ / * * 20 20* * Motor Modifications Continued AC Coil Brakes a. Brake Torque must be specified when ordering. b. Enclosures Standard - suitable for indoor clean/dry environments. Stock shur-stop brakes have this enclosure. Waterproof/dust tight - for applications involving washdown, Corro-Duty and outdoors. Not suitable for hazardous Class 2 dust applications. Leadtimes may be encountered. Explosionproof - explosionproof gearmotors with brakes require the same UL rating as the motor. Brakes will typically be rated Cl I Grp D and Cl II Groups F&G temperature code T3B. Production lead-times apply and for 56/140T motor frame requirements, refer to Application Engineering before quoting. c. Operating Voltage Through 35 ft. lbs. can be supplied with 115V, 230V, 460V or 575V coils. Brakes above 35 ft. lbs. can be supplied with 460V or 575V coils. Any voltage required different than above should be referred to Application Engineering before quoting. d. Mounting Position Brakes through 6 ft. lbs. are suitable for all mounting positions. Brakes > 6 ft. lbs. require specification of mounting if vertical mounting is required. Vertical mounting will be at lead-time. DC Coil Brakes (FCR) a. Brake Torque on this design will be 1.5 times the motor full load torque. b. Enclosures IP54 applicable to these brakes making them suitable for all environments (inside and outdoors) that TEFC motors are used. c. Operating Voltages Standard brake coils will be 180 VDC based on rectifying 230VAC. Rectifier is supplied in the motor outlet box. Provisions on 230/460V and 575V motors are made to power rectifier from the motor. For 100VDC and other coils, refer to Application Engineering. d. Mounting Positions Standard FCR DC brake designs will operate in any position specified for the gearmotor. D-23 Series

24 Gearmotors Modifications, Options and Accessories Motor Modifications Continued Motor Modifications Continued M2 Premium Efficiency Premium efficiency motor designs are available starting at 1 HP to meet customer specifications or NRCan legislation. Corro-Duty motors 3 HP and all inverter duty motors meet premium efficiency requirements as standard. TEFC and Corro-Duty motor ends from 1 through 2 HP are design C and therefore are exempt from NRCan efficiency requirements. M5 Frequency - 50 Hz Motors for operation at 3 phase 50 Hz are available. Standard 50 Hz voltage (detailed in M6) do not require voltage modification. The published output speed, based on 1750 rpm input, will be reduced by a factor of (1.2) at the same gear ratio. Example: 100 rpm output, 60 Hz, 1750 rpm input is 83 rpm output, 50 Hz, 1450 rpm input. Series M3 Multi-Speed (3 Phase Only) Gearmotors with 1800 rpm motors as standard can be supplied with two speed, one winding, constant torque, 1800/900 rpm, 1.0 service factor, TEFC motor ends. Note that change in motor frame may change gearbox size. Thus, if gear frame is not within allowable range, it may be necessary to change gear frame size. Table 2 HP Frame Allowable Gear Frames.33/ / Size 31 2 Stages.75/ T Sizes Stages 1.0/ T Sizes 32-35, Stages 1.5/ TY 2.0/ T 3.0/ T Size 31 2 Stages Sizes Stages Size 26 3 Stages Sizes 34-35, Stages Size 32 2 Stages 5.0/ T Sizes 33-35, Stages Sizes 34-35, Stages 7.5/ T Size 33 2 Stages 5-Oct 256T Sizes 34-35, Stages Size Stages 15/ T Size 34 2 Stages 20/10 286T Sizes 35, Stages 25/ T Size 26 2 Stages 30/15 326T Size Stages M4 Canopy Cap A canopy cap can be supplied for protection from dripping liquids entering fan end of gearmotor when mounted in a motor fan up position (PV5). M6 Voltage (3 Phase Only) Standard voltages are listed in the table below. Other voltages are available and must be specified at order entry and require special voltage adder. Frequency 3 Phase Voltages Through 30 HP 60 Hz 200, 208, 230, 230/460, 460, Hz 220, 220/380, 220/440, 190/380, 380, 400, 415 M7 Insulation Standard 3 phase TEFC and Corro-Duty motor ends have premium Q3 class F insulation standard. Single phase TEFC and explosionproof motor ends have class B insulation as standard. Class H insulation and tropical protection are available from production on 3 phase motors only (class H not available on explosionproof). M8 Space Heaters Space heaters are recommended for gearmotors installed in damp locations to prevent condensation on the motor windings when the motor is not operating. Leads are brought to the standard motor conduit box. Space heater voltage (115, 230, 460 volts) must be specified when the order is entered. M9 Thermal Protection - Thermostats This protection uses a bi-metal disc thermostat, embedded in the motor winding, connected into the holding circuit of the motor starter. The sensor opens the control circuit, shutting down the motor on over temperature. Thermostats give protection for running overload, abnormally high ambient, voltage unbalance, high or low voltage and ventilation failure. Thermostats will not give protection for locked rotor, starting overload and single phasing. M10 Thermal Protection - Therma-Sentry Therma-Sentry is a full protection system that consists of a solid state electronic controller and thermistor temperature sensors embedded in the motor winding. In addition to all the protections provided by a thermostat, Therma-Sentry also protects against locked rotor, starting overload and single phasing. The Therma-Sentry system requires only two leads to connect to the starter panel. The Therma-Sentry controller is supplied loose to be separately mounted and separately excited. D-24

25 Gearmotors Modifications, Options and Accessories Gearmotor Modifications Gearmotor Modifications M11 Corro-Duty Corro-Duty gearmotors are designed for applications in food processing, chemical, poultry and any other industries that will be subjected to extreme humidity, washdown, steam, detergents and mild acids. Construction of Corro-Duty gearmotors begins with a Corro-Duty cast iron motor (56 and 140T frames are rolled steel) and normally closed breather in the gear case. The exterior of the entire unit is then painted in one of the two options chosen at order entry. Option #1 - Corro-Duty grey 3 step paint system using 316 stainless steel paint Light grey semigloss finish USDA and FDA approved Option #2 - Corro-Duty white 2 step paint system using epoxy paint White gloss finish USDA and FDA approved M12 Normally Closed Breather This breather helps protect against lubricant contamination in applications with flying dust, lint or washdown. A normally closed breather is standard for gear frames 32-35, or it may be added to gear frames 21 and 26 by specifying this option. M18 Oil Level View Port This clear port is installed in place of the oil level plug. It allows maintenance personnel a convenient means of checking for proper oil level without removing plugs. Proper view port part numbers are: Gear Frame Size Part Number /4 BSPP Male /4 BSPP Male Face and Flanged Output (Designated under Brackets and Shafts) Gearmotors with faced or flanged outputs are available from stock. Refer to page D-16 and individual dimension pages for options available based on gear frame size. Synthetic Oil gearmotors are supplied factory-filled with a premium synthetic oil. Refer to pages D-164 and D-165 for complete details of lubricants. M13 NPT Adapter These adapters convert metric threads of breather, drain and/or oil level holes in the reducer to standard NPT threads. They are required for customer additions of site glasses, sight tubes, special breathers and other plumbing accessories. The adapter(s) is supplied loose for mounting by others. Gear Frame Size Part Number /4 NPFT /4 NPFT M15 Export Boxing Export boxing can be provided for "underdeck" transport. When the quantity of gearmotors exceeds five units, refer to the sales department for the most economical accommodations. Series M16 Special Nameplate Units can be provided with limited, additional, special information on the standard product nameplate. When requested, a special nameplate may be provided and stamped with custom markings. D-25

26 Up to Over hrs/day hrs/day Gearmotors AGMA Application Classifications U: Uniform load M: Moderate shock load V: Heavy shock load Application Load Class Application Load Class Application Load Class Up to Over hrs/day hrs/day Up to Over hrs/day hrs/day Series Agitators Paper Mills M II II Pure Liquids U I II Liquids & Solids M II II Liquids - Variable Density M II II Apron Conveyors Uniformly Loaded or Fed U I II Heavy Duty M II II Apron Feeders M II II Assembly Conveyors Uniformly Loaded or Fed U I II Heavy Duty M II II Ball Mills V III III Barking Drums V - III Hydraulic Auxiliaries V - III Mechanical V - III Barscreens (Sewage) U I II Batchers (Textile) M II II Beaters and Pulpers (Paper) U - II Belt Conveyors Uniformly Loaded or Fed U I II Heavy Duty M II II Belt Feeders M II II Bending Rolls (Machine) M II II Bleachers (Paper) M - II Blowers Centrifugal U I II Lobe M II II Vane U I II Bottling Machinery U I II Brewing and Distilling Bottling Machinery U I II Brew Kettles, Cont. Duty U - II Can Filling Machines U I II Cookers - Cont. Duty U - II Mash Tubs - Cont. Duty U - II Scale Hoppers - Frequent Starts M II II Brick Press (Clay Working) V III III Briquetts Machines (Clay Working) V III III Bucket Conveyors, Uniform U I II Conveyors, Heavy Duty M II II Elevators Cont. U I II Elevators Uniform U I II Elevators, Heavy Duty M II II Calenders Paper U - II Super (Paper) U - II Rubber M II II Textile M II II Cane Knives M II II Can Filling Machines U I II Card Machines (Textile) M II II Car Dumpers V III - Car Pullers M II - Cement Kilns Refer to Application Engineering Centrifugal Blowers, Compressors, Discharge Elevators or Pumps U I II Chain Conveyors Uniformly Loaded or Fed U I II Heavy Duty M II II Chemical Feeders (Sewage) U I II Clarifiers U I II Classifiers M II II Clay Working Industry Brick Press V III III Briquette Machine V III III Clay Working Machinery M II II Pug Mill M II II Collectors (Sewage) U I II Compressors Centrifugal U I II Lobe M II II Reciprocating, Multi - Cylinder M II II Single - Cylinder V III III Concrete Mixers Continuous M II II Intermittent U I - Converting Machines (Paper) M - II Conveyors - Uniformly Loaded or Fed: Apron, Assembly, Belt, Bucket, Chain, Flight, Oven, Screw U I II Conveyors - Heavy Duty Not Uniformly Fed: Apron, Assembly, Belt, Bucket, Chain, Flight, Oven, Screw M II II Live Roll (Package) U I II Reciprocating, shaker V III III Cookers (Brewing and Distiling) (Food) U I II Cooling Tower Fans Induced Draft M II II Forced Draft Refer to Application Engineering Couch (Paper) M - II Cranes and Hoists Main Hoists Heavy Duty V III III Medium Duty M II II Reversing V II II Skip Hoists M II II Trolley Drive M II II Bridge Drive M II II Crushers Ore or Stone V III III Cutters (Paper) V - III Cylinders (Paper) M - II Dewatering Screens (Sewage) M II II Disc Feeders U I II Distilling (See Brewing) Double Acting Pumps 2 or more Cylinders M II II Single Cylinder Refer to Application Engineering Dough Mixer (Food) M II II Draw Bench (Metal Mills) Carriage & Main Drive V III III Dredges Cable Reels M II - Conveyors M II II Cutter Head Drives V III III Jig Drives V III III Maneuvering Winches M II - Pumps M II II Screen Drives V III III Stackers M II II Utility Winches M II - D-26

27 U: Uniform load M: Moderate shock load V: Heavy shock load Application Load Class Up to Over hrs/day hrs/day Gearmotors AGMA Application Classifications Up to Over hrs/day hrs/day Application Load Class Application Load Class Up to Over hrs/day hrs/day Dryers (Paper) U - II Dryers and Coolers (Mills, Rotary) M II II Dyeing Machinery (Textile) M II II Elevators Bucket - Uniform Load U I II Bucket - Heavy Duty M II II Bucket - Continuous U I II Centrifugal Discharge U I II Escalators U I II Freight M II II Gravity Discharge U I II Man Lifts, Passenger Refer to Application Engineering Escalators U I II Fans Centrifugal M II II Cooling Towers Induced Draft M II II Forced Draft Refer to Application Engineering Induced Draft M II II Large (Mine, etc.) M II II Large Industrial M II II Light (Small Diameter) U I II Feeders Apron, belt M II II Disc U I II Reciprocating V III III Screw M II II Felt Stretchers (Paper) U - II Whippers (Paper) U - II Flight Conveyors, Uniform U I II Conveyors, Heavy M II II Food Industry Beet Slicers M II II Bottling, Can Filling Mach. U I II Cereal Cookers U I II Dough Mixers M II II Meat Grinders M II II Forming Machines (Metal Mills) V III III Generators (Not welding) U I II Gravity Discharge Elevators U I II Grit Collectors (Sewage) U I II Hammer Mills V III III Induced Draft Fans M II II Jordans (Paper) U - II Kilns (Mills, Rotary) M II II Cement Refer to Application Engineering Laundry Washers and Tumblers M II II Line Shafts Heavy Shock Load V III III Moderate Shock Load M II II Uniform Load U I II Live Roll Conveyors Package U I II Lobe Blower or Compressors M II II Log Hauls (Paper and Lumber) V III III Looms (Textile) M II II Lumber Industry Barkers - Spindle Feed V II III Barkers - Main Drive V III III Carriage Drive Refer to Application Engineering Conveyors Burner V II III Main or Heavy Duty V II III Main Log V III III Re-Saw Merry-Go-Round V II III Slab V III III Transfer V II III Chains - Floor V II III Chains - Green V II III Cut-Off Saws-Chain V II III Cut-Off Saws-Drag V II III Debarking Drums V III III Feeds - Edger V II III Feeds - Gang V III III Feeds - Trimmer V II III Log Deck V III III Log Hauls - Incline, Well Type V III III Log Turning Devices V III III Planner Feed V II III Planer Tilting Hoists V II III Rolls - Live-Off Bearing Roll Cases V III III Sorting Table V II III Tipple Hoist V II III Transfers - Chain V II III Transfers - Craneway V II III Tray Drives V II III Machine Tools Auxiliary Drives U I II Bending Rolls M II II Main Drives M II II Notching Press (Belted) Refer to Application Engr. Plate Planers V III III Punch Press (Geared) V III III Tapping Machines V III III Mangle (Textile) M II II Mash Tubs (Brewing and Distilling) U - II Meat Grinder (Food) M II II Metal Mills Draw Bench Carriages & Main Drives V III III Forming Machines V III III Pinch, Dryer & Scrubber Rolls Reversing Refer to Application Engineering Slitters M II II Table Conveyors, Non-Reversing M II III Reversing V - III Wire Drawing & Flattening Machines M II III Wire Winding Machines M II II Mills, Rotary Type Ball, Pebble, Rod V III III Cement Kilns Refer to Application Engineering Coolers, Dryers, Kilns V II II Tumbling Barrels V III III Mixers (Also see Agitators) Concrete - Continuous M II II Concrete - Intermittent M I - Constant Density U I II Variable Density M II II Nappers (Textile) M II II Oil Industry Chillers M II II Oil Well Pumping Refer to Application Engineering Paraffin Filter Press M II II Rotary Kilns M II II Ore Crushers V III III Oven Conveyors Uniform U I II Heavy Duty M II II Series D-27

28 U: Uniform load M: Moderate shock load V: Heavy shock load Application Load Class Up to Over hrs/day hrs/day Gearmotors AGMA Application Classifications Up to Over hrs/day hrs/day Application Load Class Application Load Class Up to Over hrs/day hrs/day Series Paper Mills Agitator (Mixers) M II II Barker - Auxiliaries - Hyd. V - III Barker, Mechanical V - III Barking Drum V - III Beater & Pulper M - II Bleacher M - II Calenders M - II Calenders - Super M - II Converting Mach.- Except Cutters - Platers M - II Conveyors M - II Couch M - II Cutters, Platers V - III Cylinders U - II Dryers U - II Felt Stretchers U - II Felt Whippers V - III Jordans M - II Log Haul V - III Presses M - II Pulp Machine Reels M - II Stock Chests M - II Suction Rolls M - II Washers & Thickeners M - II Winders M - II Passenger Elevators Refer to Application Engineering Pebble Mills V III III Plate Planers V III III Presses (Paper) V - III Proportioning Pumps M II II Pub Mills (Clay) M II II Pullers (Barge Haul) V III III Pulp Machine Reels U - II Pumps Centrifugal U I II Proportioning M II II Reciprocating Single Act., 3 or more cyl. M II II Double Act., 2 or more cyl. M II II Single Act., 1 or 2 cyl. Refer to Application Engr. Rotary: Gear, Lobe, Vane U I II Punch Press (Gear Driven) V III III Reciprocating Conveyors, Feeders V III III Rod Mills V III III Rotary Pumps, Gear, Lobe, Vane U I II Screens (Sand or Gravel) V II II Rubber Industry Mixer V III III Rubber Calender M II II Rubber Mill (2 or more) M II II Sheeter M II II Tire Building Machines Refer to Application Engr. Tire, Tube Press Openers Refer to Application Engr. Tubers & Strainers M II II Sand Mullers Refer to Application Engr. Screens Air Washing U I II Rotary - Sand or Gravel M II II Traveling Water Intake U I II Screw Conveyors Uniform U I II Heavy Duty or Feeder M II II Scum Breakers (Sewage) M II II Sewage Disposal Aerators Refer to Application Engineering Bar Screens U I II Chemical Feeders U I II Collectors U I II Dewatering Screens M II II Grit Collectors U I II Scum Breakers M II II Slow or Rapid Mixers M II II Sludge Collectors U I II Thickeners M II II Vacuum Filters M II II Shaker Conveyors V III III Sheeters (Rubber) M II II Single Acting Pump 1 or 2 Cylinders Refer to Application Engineering 3 or more Cylinders M II II Skip Hoist M II II Slab Pushers M II II Slitters (Metal) M II II Soapers (Textile) M II II Spinners (Textile) M II II Steering Gears M II II Stock Chests(Paper) U - II Stokers U I II Stone Crushers V III III Suction Rolls(Paper) U - II Table Conveyors (Metal Mills) Non-Reversing V II III Reversing V - III Tenter Frames (Textile) M II II Textile Industry Batchers M II II Calenders M II II Card Machines M II II Cloth Finishing Mach. (Calenders, Dryers, Pads, Tenters, Washers) M II II Dry Cans M II II Dyeing Machinery M II II Knitting Machinery Refer to Application Engr. Looms, Mangles, Nappers M II II Range Drives Refer to Application Engr. Soapers, Spinners M II II Tenter Frames M II II Winders M II II Yarn Preparatory Mach. (Cards, Spinners, Slashers) M II II Thickeners (Sewage) M II II Tumbling Barrels V III III Vacuum Filters (sewage) M II II Vane Blowers U I II Winches (Dredges) M II - Winders (Paper) U - II (Textile) M II II Windlass M II II Reciprocating Compressors Multi-Cylinder M II II Single cylinder V III III Sludge Collectors (Sewage) U I II Wire Drawing Machines M II III Winding Machines M II II D-28 Applications not listed in this table, or where the user has data indicating the severity of this usage to be greater than average, should be referred to Application Engineering.

29 Gearmotors 1/3 HP General Specifications: Totally enclosed, 60 hertz, 40 C ambient, continuous duty. Output RPM AGMA Class Service Factor Output Torque in-lb Nominal Ratio Gear Frame Size Motor Std. Motor Types 446 I, II, III T, S, C, X, IG 354 I, II, III T, S, C, X, IG 296 I, II, III T, S, C, X, IG 250 I, II, III T, S, C, X, IG 240 I, II, III T, S, C, X, IG 235 I, II, III T, S, C, X, IG 208 I, II, III T, S, C, X, IG 196 I, II, III T, C, X 190 I, II, III T, S, C, X, IG 170 I, II, III T, S, C, X, IG 161 I, II, III T, S, C, X, IG 142 I, II, III T, S, C, X, IG 126 I, II, III T, S, C, X, IG 111 I, II, III T, S, C, X, IG 106 I, II, III T, C, X 98 I, II, III T, S, C, X, IG 94 I, II, III T, C, X 86 I, II, III T, S, C, X, IG 83 I, II, III T, C, X 76 I, II, III T, S, C, X, IG 72 I, II, III T, S, C, X, IG 65 I, II, III T, C, X 60 I, II, III T, S, C, X, IG 57 I, II, III T, S, C, X, IG 50 I, II, III T, S, C, X, IG 48 I, II, III T, C, X 45 I, II, III T, S, C, X, IG 42 I, II, III T, C, X 40 I, II, III T, S, C, X, IG 38 I, II, III T, C, X 34 I, II, III T, S, C, X, IG 31 I, II, III T, S, C, X, IG 27 I, II, III T, S, C, X, IG 25 I, II, III T, S, C, X, IG 23 I, II, III T, C, X 23 I, II, III T, S, C, X, IG 22 I, II, III T, S, C, X, IG 21 I, II, III T, C, X 19 I, II, III T, S, C, X, IG 18 I, II T, C, X Series Standard Motor Types (see page D-15 for product codes) T TEFC, three phase, /460 or 575 volts S TEFC, single phase, 115/230 volts C Corro-Duty, three phase, 230/460 or 575 volts X Explosionproof, CI 1 group D, CI 2 groups F&G, three phase, 230/460 or 575 volts IG IntelliGear variable speed for 1-ph/115V, 1-ph/230V, 3-ph/230V, or 3-ph/460V power supplies, NEMA 4/12 Denotes 6-pole (1200 rpm) motor. D-29

30 Series Gearmotors 1/3 HP (Continued) General Specifications: Totally enclosed, 60 hertz, 40 C ambient, continuous duty. Output RPM AGMA Class Service Factor Output Torque in-lb Nominal Ratio Gear Frame Size Motor Std. Motor Types 18 I, II, III T, S, C, X, IG 16 I, II T, C, X 15 I, II, III T, S, C, X, IG 14 I, II, III T, S, C, X, IG 12 I, II, III T, S, C, X, IG 10.7 I, II, III T, S, C, X, IG 10.3 I, II, III T, C, X 9.7 I, II, III T, S, C, X, IG 9.5 I, II, III T, C, X 9.1 I, II T, C, X 9.1 I, II, III T, S, C, X, IG 8.6 I, II, III T, C, X 8.5 I, II T, S, C, X, IG 8.2 I, II T, C, X 7.8 I, II, III T, S, C, X, IG 7.7 I, II T, S, C, X, IG 7.6 I, II, III T, C, X 7.1 I, II T, C, X 7.1 I, II T, S, C, X o, IG 7.1 I, II, III T, S, C, X, IG 6.8 I, II, III T, C, X 6.4 I T, C, X 6.4 I, II T, S, C, X o, IG 6.4 I, II, III T, S, C, X, IG 6.1 I, II T, S, C, X o, IG 6.0 I, II, III T, C, X 5.6 I T, C, X 5.5 I, II, III T, S, C, X, IG 5.2 I T, S, C, X o, IG 5.2 I, II, III T, C, X 5.1 I T, C, X 4.9 I, II, III T, S, C, X o, IG 4.9 I, II, III T, C, X 4.8 I T, S, C, X o, IG 4.7 I, II T, C, X 4.6 I, II T, S, C, X o, IG 4.3 I T, S, C, X o, IG 4.3 I, II T, C, X 4.2 I, II, III T, S, C, X, IG 3.9 I, II T, S, C, X o, IG Standard Motor Types (see page D-15 for product codes) T TEFC, three phase, /460 or 575 volts S TEFC, single phase, 115/230 volts C Corro-Duty, three phase, 230/460 or 575 volts X Explosionproof, CL1 group D, three phase, 230/460 or 575 volts X Explosionproof, CI 1 group D, CI 2 groups F&G, three phase, 230/460 or 575 volts IG IntelliGear variable speed for 1-ph/115V, 1-ph/230V, 3-ph/230V, or 3-ph/460V power supplies, NEMA 4/12 Denotes 6-pole (1200 rpm) motor. D-30

31 Gearmotors 1/3 HP (Continued) General Specifications: Totally enclosed, 60 hertz, 40 C ambient, continuous duty. Output RPM AGMA Class Service Factor Output Torque in-lb Nominal Ratio Gear Frame Size Motor Std. Motor Types 3.6 I T, C, X 3.6 I, II T, S, C, X o, IG 3.6 I, II, III T, S, C, X, IG 3.3 I T, S, C, X o, IG 3.2 I, II, III T, S, C, X, IG 3.0 I, II, III T, S, C, X, IG 2.8 I T, S, C, X o, IG 2.6 I T, S, C, X o, IG 2.6 I, II, III T, S, C, X, IG 2.4 I, II T, S, C, X, IG 2.3 I, II, III T, S, C, X, IG 2.1 I, II T, S, C, X, IG 2.0 I, II, III T, S, C, X, IG 1.9 I, II T, S, C, X, IG 1.9 I, II, III T, S, C, X, IG 1.7 I T, S, C, X, IG 1.6 I, II, III T, S, C, X, IG 1.5 I T, S, C, X, IG 1.5 I, II, III T, S, C, X, IG 1.3 I T, S, C, X, IG 1.3 I, II T, S, C, X, IG 1.3 I, II, III A 56 T, S, C, X, IG 1.2 I, II T, S, C, X, IG 1.2 I, II, III A 56 T, S, C, X, IG 1.1 I, II T, S, C, X, IG 1.1 I, II, III A 56 T, S, C, X, IG 0.95 I, II, III A 56 T, S, C, X, IG 0.92 I T, S, C, X, IG 0.85 I, II, III A 56 T, S, C, X, IG 0.84 I T, S, C, X, IG 0.75 I, II A 56 T, S, C, X, IG 0.73 I T, S, C, X, IG 0.69 I, II A 56 T, S, C, X, IG 0.61 I, II A 56 T, S, C, X, IG 0.53 I A 56 T, S, C, X, IG 0.47 I A 56 T, S, C, X, IG 0.43 I A 56 T, S, C, X, IG Series Standard Motor Types (see page D-15 for product codes) T TEFC, three phase, /460 or 575 volts S TEFC, single phase, 115/230 volts C Corro-Duty, three phase, 230/460 or 575 volts X Explosionproof, CL1 group D, three phase, 230/460 or 575 volts X Explosionproof, CI 1 group D, CI 2 groups F&G, three phase, 230/460 or 575 volts IG IntelliGear variable speed for 1-ph/115V, 1-ph/230V, 3-ph/230V, or 3-ph/460V power supplies, NEMA 4/12 Denotes 6-pole (1200 rpm) motor. D-31

32 Series Gearmotors 1/2 HP General Specifications: Totally enclosed, 60 hertz, 40 C ambient, continuous duty. Output RPM AGMA Class Service Factor Output Torque in-lb Nominal Ratio Gear Frame Size Motor Std. Motor Types 446 I, II, III T, S, C, X, IG 354 I, II, III T, S, C, X, IG 296 I, II, III T, S, C, X, IG 250 I, II, III T, S, C, X, IG 240 I, II, III T, S, C, X, IG 235 I, II, III T, S, C, X, IG 208 I, II, III T, S, C, X, IG 196 I, II, III T, C, X 190 I, II, III T, S, C, X, IG 170 I, II, III T, S, C, X, IG 161 I, II, III T, S, C, X, IG 142 I, II, III T, S, C, X, IG 126 I, II, III T, S, C, X, IG 111 I, II, III T, S, C, X, IG 106 I, II, III T, C, X 98 I, II, III T, S, C, X, IG 94 I, II, III T, C, X 86 I, II, III T, S, C, X, IG 83 I, II, III T, C, X 76 I, II, III T, S, C, X, IG 72 I, II, III T, S, C, X, IG 65 I, II, III T, C, X 60 I, II, III T, S, C, X, IG 57 I, II, III T, S, C, X, IG 50 I, II, III T, S, C, X, IG 48 I, II, III T, C, X 45 I, II, III T, S, C, X, IG 42 I, II, III T, C, X 40 I, II, III T, S, C, X, IG 38 I, II, III T, C, X 34 I, II, III T, S, C, X, IG 31 I, II, III T, S, C, X, IG 27 I, II T, S, C, X, IG 27 I, II, III T, S, C, X, IG 25 I, II T, S, C, X, IG 23 I, II, III T, S, C, X, IG 22 I, II, III T, S, C, X, IG 21 I, II T, C, X 19 I, II, III T, S, C, X, IG 18 I T, C, X Standard Motor Types (see page D-15 for product codes) T TEFC, three phase, /460 or 575 volts S TEFC, single phase, 115/230 volts C Corro-Duty, three phase, 230/460 or 575 volts X Explosionproof, CI 1 group D, CI 2 groups F&G, three phase, 230/460 or 575 volts IG IntelliGear variable speed for 1-ph/115V, 1-ph/230V, 3-ph/230V, or 3-ph/460V power supplies, NEMA 4/12 Denotes 6-pole (1200 rpm) motor. D-32

33 Gearmotors 1/2 HP (Continued) General Specifications: Totally enclosed, 60 hertz, 40 C ambient, continuous duty. Output RPM AGMA Class Service Factor Output Torque in-lb Nominal Ratio Gear Frame Size Motor Std. Motor Types 18 I, II, III T, S, C, X, IG 16 I T, C, X 16 I, II T, C, X 16 I, II, III T, S, C, X, IG 15 I, II T, S, C, X, IG 15 I, II, III T, C, X 14 I, II T, S, C, X, IG 14 I, II, III T, S, C, X, IG 13 I, II, III T, S, C, X, IG 12 I, II T, S, C, X, IG 12 I, II, III T, C, X 11 I, II, III T, S, C, X, IG 10.7 I, II T, S, C, X, IG 10.3 I T, C, X 10.2 I, II, III T, S, C, X, IG 9.7 I T, S, C, X, IG 9.5 I, II, III T, C, X 9.1 I T, C, X 9.1 I, II, III T, S, C, X, IG 8.6 I, II, III T, C, X 8.5 I T, S, C, X, IG 8.2 I T, C, X 7.8 I, II, III T, S, C, X, IG 7.7 I T, S, C, X, IG 7.6 I, II T, C, X 7.4 I, II, III T, S, C, X, IG 7.1 I T, C, X 7.1 I T, S, C, X o, IG 7.1 I, II T, S, C, X, IG 7.0 I, II, III T, C, X 6.8 I, II T, C, X 6.4 I T, S, C, X o, IG 6.4 I, II T, S, C, X, IG 6.1 I, II, III T, C, X 6.0 I, II T, C, X 6.0 I, II, III T, S, C, X, IG 5.5 I T, S, C, X, IG 5.5 I, II, III T, C, X 5.3 I, II, III T, S, C, X, IG 5.2 I T, C, X Series Standard Motor Types (see page D-15 for product codes) T TEFC, three phase, /460 or 575 volts S TEFC, single phase, 115/230 volts C Corro-Duty, three phase, 230/460 or 575 volts X Explosionproof, CL1 group D, three phase, 230/460 or 575 volts X Explosionproof, CI 1 group D, CI 2 groups F&G, three phase, 230/460 or 575 volts IG IntelliGear variable speed for 1-ph/115V, 1-ph/230V, 3-ph/230V, or 3-ph/460V power supplies, NEMA 4/12 Denotes 6-pole (1200 rpm) motor. D-33

34 Series Gearmotors 1/2 HP (Continued) General Specifications: Totally enclosed, 60 hertz, 40 C ambient, continuous duty. Output RPM AGMA Class Service Factor Output Torque in-lb Nominal Ratio Gear Frame Size Motor Std. Motor Types 4.9 I T, S, C, X o, IG 4.9 I, II, III T, C, X 4.7 I T, C, X 4.7 I, II, III T, S, C, X, IG 4.6 I T, S, C, X o, IG 4.3 I T, C, X 4.2 I, II, III T, S, C, X, IG 3.9 I T, S, C, X o, IG 3.9 I, II, III T, S, C, X, IG 3.7 I, II, III T, S, C, X, IG 3.6 I T, S, C, X o, IG 3.6 I, II T, S, C, X, IG 3.2 I, II T, S, C, X, IG 3.0 I, II T, S, C, X, IG 3.0 I, II, III T, S, C, X, IG 2.6 I, II T, S, C, X, IG 2.6 I, II, III T, S, C, X, IG 2.4 I T, S, C, X, IG 2.3 I, II, III T, S, C, X, IG 2.2 I, II, III A 56 T, S, C, X, IG 2.1 I T, S, C, X, IG 2.0 I, II T, S, C, X, IG 1.9 I T, S, C, X, IG 1.9 I, II T, S, C, X, IG 1.9 I, II, III A 56 T, S, C, X, IG 1.8 I, II, III A 56 T, S, C, X, IG 1.6 I, II T, S, C, X, IG 1.5 I, II T, S, C, X, IG 1.5 I, II, III A 56 T, S, C, X, IG 1.3 I T, S, C, X, IG 1.3 I, II, III A 56 T, S, C, X, IG 1.2 I T, S, C, X, IG 1.2 I, II A 56 T, S, C, X, IG 1.1 I T, S, C, X, IG 1.1 I, II A 56 T, S, C, X, IG 0.95 I, II A 56 T, S, C, X, IG 0.85 I A 56 T, S, C, X, IG 0.75 I A 56 T, S, C, X, IG 0.69 I A 56 T, S, C, X, IG Standard Motor Types (see page D-15 for product codes) T TEFC, three phase, /460 or 575 volts S TEFC, single phase, 115/230 volts C Corro-Duty, three phase, 230/460 or 575 volts X Explosionproof, CL1 group D, three phase, 230/460 or 575 volts X Explosionproof, CI 1 group D, CI 2 groups F&G, three phase, 230/460 or 575 volts IG IntelliGear variable speed for 1-ph/115V, 1-ph/230V, 3-ph/230V, or 3-ph/460V power supplies, NEMA 4/12 Denotes 6-pole (1200 rpm) motor. D-34

35 Gearmotors 3/4 HP General Specifications: Totally enclosed, 60 hertz, 40 C ambient, continuous duty. Output RPM AGMA Class Service Factor Output Torque in-lb Nominal Ratio Gear Frame Size Motor Std. Motor Types 446 I, II, III T, S, C, X, IG 354 I, II, III T, S, C, X, IG 296 I, II, III T, S, C, X, IG 250 I, II, III T, S, C, X, IG 240 I, II, III T, S, C, X, IG 235 I, II, III T, S, C, X, IG 208 I, II, III T, S, C, X, IG 196 I, II, III T T, C, X 190 I, II, III T, S, C, X, IG 170 I, II, III T, S, C, X, IG 161 I, II, III T, S, C, X, IG 142 I, II, III T, S, C, X, IG 126 I, II, III T, S, C, X, IG 111 I, II, III T, S, C, X, IG 106 I, II, III T T, C, X 98 I, II, III T, S, C, X, IG 94 I, II, III T T, C, X 86 I, II, III T, S, C, X, IG 83 I, II, III T T, C, X 76 I, II, III T, S, C, X, IG 72 I, II, III T, S, C, X, IG 65 I, II, III T T, C, X 60 I, II, III T, S, C, X, IG 57 I, II, III T, S, C, X, IG 50 I, II, III T, S, C, X, IG 48 I, II, III T T, C, X 45 I, II, III T, S, C, X, IG 42 I, II, III T T, C, X 40 I, II T, S, C, X, IG 39 I, II, III T, S, C, X, IG 38 I, II T T, C, X 35 I, II, III T T, C, X 34 I, II, III T, S, C, X, IG 34 I, II T, S, C, X, IG 33 I, II, III T T, C, X 33 I, II T T, C, X 31 I, II T, S, C, X, IG 30 I, II, III T, S, C, X, IG 30 I, II T T, C, X 29 I, II, III T, S, C, X, IG Series Standard Motor Types (see page D-15 for product codes) T TEFC, three phase, /460 or 575 volts S TEFC, single phase, 115/230 volts C Corro-Duty, three phase, 230/460 or 575 volts X Explosionproof, CI 1 group D, CI 2 groups F&G, three phase, 230/460 or 575 volts IG IntelliGear variable speed for 1-ph/115V, 1-ph/230V, 3-ph/230V, or 3-ph/460V power supplies, NEMA 4/12 Denotes 6-pole (1200 rpm) motor. D-35

36 Series Gearmotors 3/4 HP (Continued) General Specifications: Totally enclosed, 60 hertz, 40 C ambient, continuous duty. Output RPM AGMA Class Service Factor Output Torque in-lb Nominal Ratio Gear Frame Size Motor Std. Motor Types 27 I, II T, S, C, X, IG 27 I T, S, C, X, IG 25 I, II, III T, S, C, X, IG 25 I T, S, C, X, IG 23 I, II, III T, S, C, X, IG 23 I, II T, S, C, X, IG 23 I T T, C, X 22 I, II T, S, C, X, IG 21 I, II, III T T, C, X 21 I T T, C, X 20 I, II, III T, S, C, X, IG 19 I, II T, S, C, X, IG 18 I, II, III T, S, C, X, IG 18 I, II T, S, C, X, IG 16 I, II, III T, S, C, X, IG 16 I T T, C, X 15 I T, S, C, X, IG 14 I, II, III T, S, C, X, IG 14 I T, S, C, X, IG 13 I, II, III T, S, C, X, IG 12 I T, S, C, X, IG 11 I, II, III T, S, C, X, IG 10.6 I, II, III T, S, C, X, IG 10.2 I, II T, S, C, X, IG 9.7 I, II, III T T, C, X 9.5 I, II T T, C, X 9.2 I, II, III T, S, C, X, IG 9.1 I, II T, S, C, X, IG 8.7 I, II, III T T, C, X 8.6 I, II T T, C, X 8.3 I, II, III T, S, C, X, IG 7.9 I, II, III T T, C, X 7.8 I T, S, C, X, IG 7.4 I, II, III T, S, C, X, IG 7.1 I T, S, C, X, IG 7.0 I, II, III T T, C, X 6.8 I T T, C, X 6.4 I T, S, C, X, IG 6.1 I, II, III T T, C, X 6.0 I, II, III T, S, C, X, IG Standard Motor Types (see page D-15 for product codes) T TEFC, three phase, /460 or 575 volts S TEFC, single phase, 115/230 volts C Corro-Duty, three phase, 230/460 or 575 volts X Explosionproof, CI 1 group D, CI 2 groups F&G, three phase, 230/460 or 575 volts IG IntelliGear variable speed for 1-ph/115V, 1-ph/230V, 3-ph/230V, or 3-ph/460V power supplies, NEMA 4/12 Denotes 6-pole (1200 rpm) motor. D-36

37 Gearmotors 3/4 HP (Continued) General Specifications: Totally enclosed, 60 hertz, 40 C ambient, continuous duty. Output RPM AGMA Class Service Factor Output Torque in-lb Nominal Ratio Gear Frame Size Motor Std. Motor Types 6.0 I T T, C, X 5.5 I, II, III T, S, C, X, IG 5.5 I, II T T, C, X 5.4 I, II, III T T, C, X 5.3 I, II T, S, C, X, IG 5.1 I, II, III T, S, C, X, IG 4.9 I, II T T, C, X 4.7 I, II T, S, C, X, IG 4.4 I, II, III T, S, C, X, IG 4.2 I, II T, S, C, X, IG 3.9 I, II, III T, S, C, X, IG 3.7 I, II, III T, S, C, X, IG 3.6 I T, S, C, X, IG 3.2 I T, S, C, X, IG 3.1 I, II, III A 56 T, S, C, X, IG 3.0 I, II T, S, C, X, IG 3.0 I T, S, C, X, IG 2.8 I, II, III A 56 T, S, C, X, IG 2.6 I, II T, S, C, X, IG 2.5 I, II, III A 56 T, S, C, X, IG 2.3 I, II T, S, C, X, IG 2.2 I, II, III A 56 T, S, C, X, IG 2.0 I T, S, C, X, IG 1.9 I, II, III A 56 T, S, C, X, IG 1.9 I T, S, C, X, IG 1.8 I, II A 56 T, S, C, X, IG 1.6 I T, S, C, X, IG 1.5 I, II A 56 T, S, C, X, IG 1.5 I T, S, C, X, IG 1.3 I A 56 T, S, C, X, IG 1.2 I A 56 T, S, C, X, IG 1.1 I A 56 T, S, C, X, IG 1.0 I A 56 T, S, C, X, IG Series Standard Motor Types (see page D-15 for product codes) T TEFC, three phase, /460 or 575 volts S TEFC, single phase, 115/230 volts C Corro-Duty, three phase, 230/460 or 575 volts X Explosionproof, CI 1 group D, CI 2 groups F&G, three phase, 230/460 or 575 volts IG IntelliGear variable speed for 1-ph/115V, 1-ph/230V, 3-ph/230V, or 3-ph/460V power supplies, NEMA 4/12 Denotes 6-pole (1200 rpm) motor. D-37

38 Series Gearmotors 1 HP General Specifications: Totally enclosed, 60 hertz, 40 C ambient, continuous duty. Output RPM AGMA Class Service Factor Output Torque in-lb Nominal Ratio Gear Frame Size Motor Std. Motor Types 446 I, II, III T T, S, C, X, IG 354 I, II, III T T, S, C, X, IG 296 I, II, III T T, S, C, X, IG 250 I, II, III T T, S, C, X, IG 240 I, II, III T T, S, C, X, IG 235 I, II, III T T, S, C, X, IG 208 I, II, III T T, S, C, X, IG 196 I, II, III T T, C, X 190 I, II, III T T, S, C, X, IG 170 I, II, III T T, S, C, X, IG 161 I, II, III T T, S, C, X, IG 142 I, II, III T T, S, C, X, IG 126 I, II, III T T, S, C, X, IG 111 I, II, III T T, S, C, X, IG 106 I, II, III T T, C, X 98 I, II, III T T, S, C, X, IG 94 I, II, III T T, S, C, X, IG 86 I, II, III T T, S, C, X, IG 83 I, II, III T T, C, X 76 I, II, III T T, S, C, X, IG 72 I, II, III T T, S, C, X, IG 65 I, II, III T T, C, X 60 I, II, III T T, S, C, X, IG 57 I, II T T, S, C, X, IG 53 I, II, III T T, S, C, X, IG 50 I, II T T, S, C, X, IG 50 I, II, III T T, S, C, X, IG 48 I, II T T, C, X 46 I, II, III T T, S, C, X, IG 45 I, II T T, S, C, X, IG 44 I, II T T, S, C, X, IG 42 I, II, III T T, C, X 40 I, II T T, S, C, X, IG 40 I, II, III T T, S, C, X, IG 39 I, II, III T T, C, X 39 I, II T T, S, C, X, IG 38 I T T, C, X 36 I, II, III T T, S, C, X, IG 34 I T T, S, C, X, IG 34 I, II T T, S, C, X, IG Standard Motor Types (see page D-15 for product codes) T TEFC, three phase, /460 or 575 volts S TEFC, single phase, 115/230 volts C Corro-Duty, three phase, 230/460 or 575 volts X Explosionproof, CI 1 group D, CI 2 groups F&G, three phase, 230/460 or 575 volts IG IntelliGear variable speed for 1-ph/230V, 3-ph/230V, or 3-ph/460V power supplies, NEMA 4/12 Denotes 6-pole (1200 rpm) motor. D-38

39 Gearmotors 1 HP (Continued) General Specifications: Totally enclosed, 60 hertz, 40 C ambient, continuous duty. Output RPM AGMA Class Service Factor Output Torque in-lb Nominal Ratio Gear Frame Size Motor Std. Motor Types 33 I, II, III T T, C, X 32 I, II, III T T, S, C, X, IG 31 I T T, S, C, X, IG 30 I, II T T, S, C, X, IG 30 I, II, III T T, C, X 29 I, II, III T T, S, C, X, IG 27 I, II T T, S, C, X, IG 26 I, II, III T T, C, X 25 I, II, III T T, S, C, X, IG 24 I, II, III T T, C, X 23 I T T, S, C, X, IG 23 I, II, III T T, S, C, X, IG 22 I T T, S, C, X, IG 21 I, II, III T T, C, X 20 I, II, III T T, S, C, X, IG 19 I T T, S, C, X, IG 18 I T T, S, C, X, IG 18 I, II, III T T, S, C, X, IG 17 I, II, III T T, S, C, X, IG 16 I T T, C, X 16 I, II T T, S, C, X, IG 15 I, II, III T T, S, C, X, IG 14 I, II T T, S, C, X, IG 13 I, II T T, S, C, X, IG 13 I, II, III T T, S, C, X, IG 12 I, II, III T T, S, C, X, IG 11 I, II T T, S, C, X, IG 10.9 I, II, III T T, C, X 10.6 I, II, III T T, S, C, X, IG 10.2 I T T, S, C, X, IG 9.7 I, II, III T T, C, X 9.5 I T T, C, X 9.2 I, II, III T T, S, C, X, IG 9.1 I T T, S, C, X, IG 8.7 I, II, III T T, C, X 8.6 I T T, C, X 8.3 I, II, III T T, S, C, X, IG 7.9 I, II, III T T, C, X 7.8 I T T, S, C, X, IG 7.4 I, II, III T T, S, C, X, IG Series Standard Motor Types (see page D-15 for product codes) T TEFC, three phase, /460 or 575 volts S TEFC, single phase, 115/230 volts C Corro-Duty, three phase, 230/460 or 575 volts X Explosionproof, CI 1 group D, CI 2 groups F&G, three phase, 230/460 or 575 volts IG IntelliGear variable speed for 1-ph/230V, 3-ph/230V, or 3-ph/460V power supplies, NEMA 4/12 Denotes 6-pole (1200 rpm) motor. D-39

40 Series Gearmotors 1 HP (Continued) General Specifications: Totally enclosed, 60 hertz, 40 C ambient, continuous duty. Output RPM AGMA Class Service Factor Output Torque in-lb Nominal Ratio Gear Frame Size Motor Std. Motor Types 7.0 I, II T T, C, X 6.9 I, II, III T T, C, X 6.3 I, II, III T T, C, X 6.3 I, II, III T T, S, C, X, IG 6.1 I, II T T, C, X 6.0 I, II T T, S, C, X, IG 5.5 I, II T T, C, X 5.5 I, II, III T T, S, C, X, IG 5.4 I, II, III T T, C, X 5.3 I, II T T, S, C, X, IG 5.1 I, II, III T T, S, C, X, IG 4.9 I T T, C, X 4.7 I T T, S, C, X, IG 4.4 I, II, III T T, S, C, X, IG 4.2 I T T, S, C, X, IG 3.9 I, II T T, S, C, X, IG 3.9 I, II, III A 143T T, S, C, X, IG 3.7 I, II T T, S, C, X, IG 3.6 I T T, S, C, X, IG 3.5 I, II, III A 143T T, S, C, X, IG 3.1 I, II, III A 143T T, S, C, X, IG 3.0 I, II T T, S, C, X, IG 2.8 I, II, III A 143T T, S, C, X, IG 2.6 I T T, S, C, X, IG 2.5 I, II A 143T T, S, C, X, IG 2.3 I T T, S, C, X, IG 2.2 I, II A 143T T, S, C, X, IG 2.0 I T T, S, C, X, IG 1.9 I, II A 143T T, S, C, X, IG 1.8 I A 143T T, S, C, X, IG 1.5 I A 143T T, S, C, X, IG 1.3 I A 143T T, S, C, X, IG Standard Motor Types (see page D-15 for product codes) T TEFC, three phase, /460 or 575 volts S TEFC, single phase, 115/230 volts C Corro-Duty, three phase, 230/460 or 575 volts X Explosionproof, CI 1 group D, CI 2 groups F&G, three phase, 230/460 or 575 volts IG IntelliGear variable speed for 1-ph/230V, 3-ph/230V, or 3-ph/460V power supplies, NEMA 4/12 Denotes 6-pole (1200 rpm) motor. D-40

41 Gearmotors 1 1/2 HP General Specifications: Totally enclosed, 60 hertz, 40 C ambient, continuous duty. Output RPM AGMA Class Service Factor Output Torque in-lb Nominal Ratio Gear Frame Size Motor Std. Motor Types 446 I, II, III T T, S, C, X, IG 354 I, II, III T T, S, C, X, IG 296 I, II, III T T, S, C, X, IG 250 I, II, III T T, S, C, X, IG 240 I, II, III T T, S, C, X, IG 235 I, II, III T T, S, C, X, IG 208 I, II, III T T, S, C, X, IG 196 I, II, III T T, C, X 190 I, II, III T T, S, C, X, IG 170 I, II, III T T, S, C, X, IG 161 I, II, III T T, S, C, X, IG 142 I, II, III T T, S, C, X, IG 126 I, II, III T T, S, C, X, IG 111 I, II, III T T, S, C, X, IG 106 I, II, III T T, C, X 98 I, II, III T T, S, C, X, IG 94 I, II, III T T, S, C, X, IG 86 I, II T T, S, C, X, IG 84 I, II, III T T, S, C, X, IG 83 I, II T T, C, X 78 I, II, III T T, C, X 76 I, II T T, S, C, X, IG 74 I, II, III T T, S, C, X, IG 72 I, II T T, S, C, X, IG 70 I, II, III T T, C, X 65 I, II T T, C, X 64 I, II, III T T, S, C, X, IG 62 I, II, III T T, C, X 60 I, II T T, S, C, X, IG 59 I, II, III T T, S, C, X, IG 57 I T T, S, C, X, IG 56 I, II, III T T, C, X 53 I, II, III T T, S, C, X, IG 50 I T T, S, C, X, IG 50 I, II, III T T, S, C, X, IG 48 I T T, C, X 48 I, II, III T T, C, X 46 I, II, III T T, S, C, X, IG 45 I T T, S, C, X, IG 44 I T T, S, C, X, IG Series Standard Motor Types (see page D-15 for product codes) T TEFC, three phase, /460 or 575 volts S TEFC, single phase, 115/230 volts C Corro-Duty, three phase, 230/460 or 575 volts X Explosionproof, CI 1 group D, CI 2 groups F&G, three phase, 230/460 or 575 volts IG IntelliGear variable speed for 1-ph/230V, 3-ph/230V, or 3-ph/460V power supplies, NEMA 4/12 Denotes 6-pole (1200 rpm) motor. Single phase motor has 145TY frame. D-41

42 Gearmotors 1 1/2 HP (Continued) General Specifications: Totally enclosed, 60 hertz, 40 C ambient, continuous duty. Series Output RPM AGMA Class Service Factor Output Torque in-lb Nominal Ratio Gear Frame Size Motor Std. Motor Types 42 I, II T T, C, X 42 I, II, III T T, C, X 40 I, II, III T T, S, C, X, IG 39 I, II T T, C, X 39 I T T, S, C, X, IG 36 I, II, III T T, S, C, X, IG 35 I, II T T, C, X 34 I T T, S, C, X, IG 34 I, II, III T T, C, X 32 I, II, III T T, S, C, X, IG 30 I T T, S, C, X, IG 30 I, II, III T T, C, X 29 I, II, III T T, S, C, X, IG 26 I, II, III T T, C, X 26 I, II, III T T, S, C, X, IG 25 I, II T T, S, C, X, IG 24 I, II, III T T, C, X 23 I, II T T, S, C, X, IG 23 I, II, III T T, S, C, X, IG 22 I, II, III T T, C, X 21 I, II T T, C, X 20 I, II T T, S, C, X, IG 20 I, II, III T T, S, C, X, IG 18 I, II T T, S, C, X, IG 18 I, II, III T T, S, C, X, IG 17 I T T, C, X 17 I, II, III T T, S, C, X, IG 16 I T T, S, C, X, IG 15 I, II, III T T, S, C, X, IG 14 I T T, S, C, X, IG 13 I T T, S, C, X, IG 13 I, II, III T T, S, C, X, IG 12 I, II, III T T, S, C, X, IG 11 I T T, S, C, X, IG 11 I, II, III T T, C, X 10.9 I, II T T, C, X 10.6 I, II T T, S, C, X, IG 10.4 I, II, III T T, S, C, X, IG 9.9 I, II, III T T, C, X 9.7 I, II T T, C, X Standard Motor Types (see page D-15 for product codes) T TEFC, three phase, /460 or 575 volts S TEFC, single phase, 115/230 volts C Corro-Duty, three phase, 230/460 or 575 volts X Explosionproof, CI 1 group D, CI 2 groups F&G, three phase, 230/460 or 575 volts IG IntelliGear variable speed for 1-ph/230V, 3-ph/230V, or 3-ph/460V power supplies, NEMA 4/12 Denotes 6-pole (1200 rpm) motor. Single phase motor has 145TY frame. D-42

43 Gearmotors 1 1/2 HP (Continued) General Specifications: Totally enclosed, 60 hertz, 40 C ambient, continuous duty. Output RPM AGMA Class Service Factor Output Torque in-lb Nominal Ratio Gear Frame Size Motor Std. Motor Types 9.5 I, II, III T T, S, C, X, IG 9.2 I, II T T, S, C, X, IG 8.9 I, II, III T T, C, X 8.7 I, II T T, C, X 8.3 I, II T T, S, C, X, IG 8.1 I, II, III T T, S, C, X, IG 7.9 I, II T T, C, X 7.8 I, II, III T T, C, X 7.4 I T T, S, C, X, IG 7.1 I, II, III T T, S, C, X, IG 7.0 I T T, C, X 6.9 I, II T T, C, X 6.7 I, II, III T T, C, X 6.3 I, II T T, C, X 6.3 I, II T T, S, C, X, IG 6.1 I T T, C, X 6.1 I, II, III A 145T T, S, C, X, IG 6.0 I T T, S, C, X, IG 5.8 I, II, III T T, C, X 5.5 I T T, C, X 5.5 I, II T T, S, C, X, IG 5.4 I, II T T, C, X 5.3 I, II, III A 145T T, S, C, X, IG 5.1 I, II T T, S, C, X, IG 4.7 I, II, III A 145T T, S, C, X, IG 4.4 I T T, S, C, X, IG 4.4 I, II, III A 145T T, S, C, X, IG 3.9 I T T, S, C, X, IG 3.9 I, II, III A 145T T, S, C, X, IG 3.7 I T T, S, C, X, IG 3.5 I, II A 145T T, S, C, X, IG 3.1 I, II A 145T T, S, C, X, IG 2.8 I, II A 145T T, S, C, X, IG 2.5 I A 145T T, S, C, X, IG 2.2 I A 145T T, S, C, X, IG 1.9 I A 145T T, S, C, X, IG Series Standard Motor Types (see page D-15 for product codes) T TEFC, three phase, /460 or 575 volts S TEFC, single phase, 115/230 volts C Corro-Duty, three phase, 230/460 or 575 volts X Explosionproof, CI 1 group D, CI 2 groups F&G, three phase, 230/460 or 575 volts IG IntelliGear variable speed for 1-ph/230V, 3-ph/230V, or 3-ph/460V power supplies, NEMA 4/12 Denotes 6-pole (1200 rpm) motor. Single phase motor has 145TY frame. D-43

44 Series Gearmotors 2 HP General Specifications: Totally enclosed, 60 hertz, 40 C ambient, continuous duty. Output RPM AGMA Class Service Factor Output Torque in-lb Nominal Ratio Gear Frame Size Motor Std. Motor Types 446 I, II, III T T, S, C, X, IG 354 I, II, III T T, S, C, X, IG 296 I, II, III T T, S, C, X, IG 250 I, II, III T T, S, C, X, IG 240 I, II, III T T, S, C, X, IG 235 I, II, III T T, S, C, X, IG 208 I, II, III T T, S, C, X, IG 196 I, II, III T T, C, X 190 I, II, III T T, S, C, X, IG 170 I, II, III T T, S, C, X, IG 161 I, II, III T T, S, C, X, IG 159 I, II T T, C, X 156 I, II, III T T, C, X 142 I, II, III T T, S, C, X, IG 138 I, II, III T T, C, X 134 I, II, III T T, S, C, X, IG 126 I, II, III T T, S, C, X, IG 117 I, II, III T T, S, C, X, IG 111 I, II T T, S, C, X, IG 109 I, II, III T T, C, X 106 I, II T T, C, X 106 I, II, III T T, S, C, X, IG 98 I, II T T, S, C, X, IG 94 I, II T T, C, X 94 I, II, III T T, S, C, X, IG 89 I, II, III T T, C, X 86 I, II T T, S, C, X, IG 84 I, II, III T T, S, C, X, IG 83 I, II T T, C, X 78 I, II, III T T, C, X 76 I T T, S, C, X, IG 74 I T T, C, X 74 I, II, III T T, S, C, X, IG 72 I T T, S, C, X, IG 70 I, II, III T T, C, X 65 I T T, C, X 64 I, II, III T T, S, C, X, IG 62 I, II, III T T, C, X 60 I T T, S, C, X, IG 59 I, II T T, S, C, X, IG 57 I T T, S, C, X, IG 56 I, II T T, C, X Standard Motor Types (see page D-15 for product codes) T TEFC, three phase, /460 or 575 volts S TEFC, single phase, 115/230 volts C Corro-Duty, three phase, 230/460 or 575 volts X Explosionproof, CI 1 group D, CI 2 groups F&G, three phase, 230/460 or 575 volts IG IntelliGear variable speed for 1-ph/230V, 3-ph/230V, or 3-ph/460V power supplies, NEMA 4/12 Denotes 6-pole (1200 rpm) motor. Single phase motors are 145TY frame. D-44

45 Gearmotors 2 HP (Continued) General Specifications: Totally enclosed, 60 hertz, 40 C ambient, continuous duty. Output RPM AGMA Class Service Factor Output Torque in-lb Nominal Ratio Gear Frame Size Motor Std. Motor Types 56 I, II, III T T, S, C, X, IG 53 I, II T T, S, C, X, IG 52 I, II, III T T, S, C, X, IG 50 I, II T T, S, C, X, IG 48 I, II, III T T, C, X 46 I, II, III T T, S, C, X, IG 42 I, II T T, C, X 42 I, II, III T T, C, X 40 I, II, III T T, S, C, X, IG 39 I T T, C, X 36 I, II, III T T, S, C, X, IG 35 I T T, C, X 34 I, II, III T T, C, X 33 I, II, III T T, S, C, X, IG 32 I, II T T, S, C, X, IG 31 I, II, III T T, C, X 30 I, II T T, C, X 29 I, II T T, S, C, X, IG 29 I, II, III T T, S, C, X, IG 28 I, II, III T T, C, X 26 I, II T T, C, X 26 I, II, III T T, S, C, X, IG 25 I, II T T, S, C, X, IG 24 I, II T T, C, X 24 I, II, III T T, C, X 23 I T T, S, C, X, IG 23 I, II, III T T, S, C, X, IG 22 I, II, III T T, C, X 21 I T T, C, X 20 I T T, S, C, X, IG 20 I, II, III T T, S, C, X, IG 19 I T T, C, X 19 I, II, III T T, C, X 18 I T T, S, C, X, IG 18 I, II, III T T, S, C, X, IG 17 I T T, C, X 17 I, II, III T T, S, C, X, IG 16 I T T, S, C, X, IG 16 I, II, III T T, C, X 15 I, II T T, S, C, X, IG 15 I, II, III T T, S, C, X, IG 14 I, II, III T T, C, X Series Standard Motor Types (see page D-15 for product codes) T TEFC, three phase, /460 or 575 volts S TEFC, single phase, 115/230 volts C Corro-Duty, three phase, 230/460 or 575 volts X Explosionproof, CI 1 group D, CI 2 groups F&G, three phase, 230/460 or 575 volts IG IntelliGear variable speed for 1-ph/230V, 3-ph/230V, or 3-ph/460V power supplies, NEMA 4/12 Denotes 6-pole (1200 rpm) motor. Single phase motors are 145TY frame. D-45

46 Series Gearmotors 2 HP (Continued) General Specifications: Totally enclosed, 60 hertz, 40 C ambient, continuous duty. Output RPM AGMA Class Service Factor Output Torque in-lb Nominal Ratio Gear Frame Size Motor Std. Motor Types 13 I, II T T, S, C, X, IG 13 I, II, III T T, S, C, X, IG 12 I, II T T, S, C, X, IG 12 I, II, III T T, S, C, X, IG 11 I, II, III T T, C, X 10.9 I, II T T, C, X 10.6 I, II T T, S, C, X, IG 10.4 I, II, III T T, S, C, X, IG 9.9 I, II T T, C, X 9.7 I T T, C, X 9.5 I, II T T, S, C, X, IG 9.3 I, II, III T T, C, X 9.2 I T T, S, C, X, IG 8.9 I, II T T, C, X 8.7 I T T, C, X 8.4 I, II, III T T, C, X 8.3 I T T, S, C, X, IG 8.1 I, II T T, S, C, X, IG 7.9 I T T, C, X 7.8 I, II T T, C, X 7.8 I, II, III A 145T T, S, C, X, IG 7.4 I, II, III T T, C, X 7.4 I T T, S, C, X, IG 7.1 I, II T T, S, C, X, IG 6.9 I T T, C, X 6.8 I, II, III A 145T T, S, C, X, IG 6.7 I, II, III T T, C, X 6.3 I T T, C, X 6.3 I, II T T, S, C, X, IG 6.1 I, II, III A 145T T, S, C, X, IG 5.8 I, II, III T T, C, X 5.5 I T T, S, C, X, IG 5.4 I T T, C, X 5.3 I, II, III A 145T T, S, C, X, IG 5.1 I T T, S, C, X, IG 4.7 I, II A 145T T, S, C, X, IG 4.4 I T T, S, C, X, IG 4.4 I, II A 145T T, S, C, X, IG 3.9 I, II A 145T T, S, C, X, IG 3.5 I A 145T T, S, C, X, IG 3.1 I A 145T T, S, C, X, IG 2.8 I A 145T T, S, C, X, IG Standard Motor Types (see page D-15 for product codes) T TEFC, three phase, /460 or 575 volts S TEFC, single phase, 115/230 volts C Corro-Duty, three phase, 230/460 or 575 volts X Explosionproof, CI 1 group D, CI 2 groups F&G, three phase, 230/460 or 575 volts IG IntelliGear variable speed for 1-ph/230V, 3-ph/230V, or 3-ph/460V power supplies, NEMA 4/12 Denotes 6-pole (1200 rpm) motor. Single phase motors are 145TY frame. D-46

47 Gearmotors 2 1/2 HP General Specifications: Totally enclosed, 60 hertz, 40 C ambient, continuous duty. Output RPM AGMA Class Service Factor Output Torque in-lb Nominal Ratio Gear Frame Size Motor Std. Motor Types 446 I, II, III TY T, C 354 I, II, III TY T, C 296 I, II, III TY T, C 250 I, II, III TY T, C 240 I, II, III TY T, C 235 I, II, III TY T, C 208 I, II, III TY T, C 190 I, II, III TY T, C 188 I, II, III TY T, C 170 I, II TY T, C 165 I, II, III TY T, C 161 I, II TY T, C 142 I, II TY T, C 142 I, II, III TY T, C 134 I, II, III TY T, C 126 I, II TY T, C 117 I, II, III TY T, C 111 I, II TY T, C 106 I, II, III TY T, C 98 I TY T, C 94 I, II, III TY T, C 86 I TY T, C 84 I, II, III TY T, C 80 I, II, III TY T, C 76 I TY T, C 74 I, II TY T, C 72 I TY T, C 72 I, II, III TY T, C 64 I, II TY T, C 64 I, II, III TY T, C 59 I, II TY T, C 56 I, II, III TY T, C 53 I, II TY T, C 52 I, II, III TY T, C 50 I TY T, C 46 I, II, III TY T, C 42 I, II, III TY T, C 40 I, II TY T, C 36 I, II TY T, C 35 I, II, III TY T, C Series Standard Motor Types (see page D-15 for product codes) T TEFC, three phase, /460 or 575 volts C Corro-Duty, three phase, 230/460 or 575 volts D-47

48 Series Gearmotors 2 1/2 HP (Continued) General Specifications: Totally enclosed, 60 hertz, 40 C ambient, continuous duty. Output RPM AGMA Class Service Factor Output Torque in-lb Nominal Ratio Gear Frame Size Motor Std. Motor Types 33 I, II, III TY T, C 32 I, II TY T, C 29 I TY T, C 29 I, II, III TY T, C 26 I, II, III TY T, C 25 I TY T, C 23 I TY T, C 23 I, II, III TY T, C 20 I, II, III TY T, C 18 I, II TY T, C 18 I, II, III TY T, C 17 I, II TY T, C 17 I, II, III TY T, C 15 I, II TY T, C 15 I, II, III TY T, C 13 I, II TY T, C 13 I, II, III TY T, C 12 I TY T, C 12 I, II TY T, C 10.6 I TY T, C 10.4 I, II TY T, C 9.5 I, II TY T, C 9.2 I TY T, C 8.1 I TY T, C 7.8 I, II, III A 145TY T, C 7.1 I TY T, C 6.8 I, II, III A 145TY T, C 6.3 I TY T, C 6.1 I, II A 145TY T, C 5.5 I TY T, C 5.3 I, II A 145TY T, C 4.7 I, II A 145TY T, C 4.4 I A 145TY T, C 3.9 I A 145TY T, C 3.5 I A 145TY T, C Standard Motor Types (see page D-15 for product codes) T TEFC, three phase, /460 or 575 volts C Corro-Duty, three phase, 230/460 or 575 volts D-48

49 Gearmotors 3 HP General Specifications: Totally enclosed, 60 hertz, 40 C ambient, continuous duty. Output RPM AGMA Class Service Factor Output Torque in-lb Nominal Ratio Gear Frame Size Motor Std. Motor Types 446 I, II, III T T, S, C, X, IG 354 I, II, III T T, S, C, X, IG 296 I, II, III T T, S, C, X, IG 250 I, II, III T T, S, C, X, IG 240 I, II T T, S, C, X, IG 235 I, II, III T T, S, C, X, IG 208 I, II, III T T, S, C, X, IG 196 I, II, III T T, C, X 190 I, II T T, S, C, X, IG 188 I, II, III T T, S, C, X, IG 170 I, II T T, S, C, X, IG 165 I, II, III T T, S, C, X, IG 161 I, II T T, S, C, X, IG 156 I, II, III T T, C, X 142 I, II T T, S, C, X, IG 142 I, II, III T T, S, C, X, IG 134 I, II, III T T, S, C, X, IG 126 I, II T T, S, C, X, IG 124 I, II, III T T, C, X 117 I, II, III T T, S, C, X, IG 111 I T T, S, C, X, IG 109 I, II, III T T, C, X 106 I, II, III T T, S, C, X, IG 98 I T T, S, C, X, IG 94 I, II, III T T, S, C, X, IG 89 I, II T T, C, X 87 I, II, III T T, S, C, X, IG 86 I T T, S, C, X, IG 84 I, II T T, S, C, X, IG 82 I, II, III T T, C, X 80 I, II, III T T, S, C, X, IG 78 I, II T T, C, X 74 I, II T T, S, C, X, IG 74 I, II, III T T, C, X 72 I, II, III T T, S, C, X, IG 70 I, II T T, C, X 64 I, II T T, S, C, X, IG 64 I, II, III T T, S, C, X, IG 62 I, II T T, C, X 59 I T T, S, C, X, IG Series Standard Motor Types (see page D-15 for product codes) T TEFC, three phase, /460 or 575 volts S TEFC, single phase, 230 volts C Corro-Duty, three phase, 230/460 or 575 volts X Explosionproof, CI 1 group D, CI 2 groups F&G, three phase, 230/460 or 575 volts IG IntelliGear variable speed for 3-ph/230V, or 3-ph/460V power supplies, NEMA 4/12 Denotes 6-pole (1200 rpm) motor. Single phase motor has 184T frame. D-49

50 Series Gearmotors 3 HP (Continued) General Specifications: Totally enclosed, 60 hertz, 40 C ambient, continuous duty. Output RPM AGMA Class Service Factor Output Torque in-lb Nominal Ratio Gear Frame Size Motor Std. Motor Types 56 I T T, C, X 56 I, II, III T T, S, C, X, IG 53 I T T, S, C, X, IG 52 I, II, III T T, S, C, X, IG 48 I, II T T, C, X 47 I, II, III T T, S, C, X, IG 46 I, II T T, S, C, X, IG 46 I, II, III T T, C, X 42 I, II T T, C, X 42 I, II, III T T, S, C, X, IG 40 I, II T T, S, C, X, IG 37 I, II, III T T, C, X 36 I, II T T, S, C, X, IG 35 I, II, III T T, S, C, X, IG 34 I T T, C, X 34 I, II, III T T, C, X 33 I, II, III T T, S, C, X, IG 32 I T T, S, C, X, IG 31 I, II, III T T, C, X 29 I T T, S, C, X, IG 29 I, II, III T T, S, C, X, IG 28 I, II, III T T, C, X 26 I, II, III T T, S, C, X, IG 25 I T T, S, C, X, IG 24 I, II, III T T, C, X 23 I, II T T, S, C, X, IG 23 I, II, III T T, S, C, X, IG 22 I, II T T, C, X 21 I, II, III T T, S, C, X, IG 20 I, II T T, S, C, X, IG 20 I, II, III T T, C, X 19 I, II T T, C, X 19 I, II, III T T, C, X 18 I, II T T, S, C, X, IG 18 I, II, III T T, S, C, X, IG 17 I, II T T, S, C, X, IG 17 I, II, III T T, S, C, X, IG 16 I, II, III T T, C, X 15 I T T, S, C, X, IG 15 I, II T T, S, C, X, IG Standard Motor Types (see page D-15 for product codes) T TEFC, three phase, /460 or 575 volts S TEFC, single phase, 230 volts C Corro-Duty, three phase, 230/460 or 575 volts X Explosionproof, CI 1 group D, CI 2 groups F&G, three phase, 230/460 or 575 volts IG IntelliGear variable speed for 3-ph/230V, or 3-ph/460V power supplies, NEMA 4/12 Denotes 6-pole (1200 rpm) motor. Single phase motor has 184T frame. D-50

51 Gearmotors 3 HP (Continued) General Specifications: Totally enclosed, 60 hertz, 40 C ambient, continuous duty. Output RPM AGMA Class Service Factor Output Torque in-lb Nominal Ratio Gear Frame Size Motor Std. Motor Types 14 I, II T T, C, X 14 I, II, III T T, S, C, X, IG 13 I T T, S, C, X, IG 13 I, II T T, S, C, X, IG 13 I, II, III T T, S, C, X, IG 12 I T T, S, C, X, IG 12 I, II T T, S, C, X, IG 11 I, II T T, C, X 11 I, II, III T T, S, C, X, IG 10.9 I T T, C, X 10.5 I, II, III T T, C, X 10.4 I T T, S, C, X, IG 10.1 I, II, III T T, S, C, X, IG 9.9 I T T, C, X 9.5 I T T, S, C, X, IG 9.3 I, II, III T T, C, X 8.9 I T T, C, X 8.7 I, II, III T T, S, C, X, IG 8.4 I, II, III T T, C, X 8.1 I T T, S, C, X, IG 7.8 I T T, C, X 7.8 I, II, III A 182T T, S, C, X, IG 7.4 I, II T T, C, X 7.1 I T T, S, C, X, IG 6.8 I, II A 182T T, S, C, X, IG 6.7 I, II T T, C, X 6.1 I, II A 182T T, S, C, X, IG 5.8 I, II T T, C, X 5.3 I A 182T T, S, C, X, IG 4.7 I A 182T T, S, C, X, IG 4.4 I A 182T T, S, C, X, IG 3.9 I A 182T T, S, C, X, IG Series Standard Motor Types (see page D-15 for product codes) T TEFC, three phase, /460 or 575 volts S TEFC, single phase, 230 volts C Corro-Duty, three phase, 230/460 or 575 volts X Explosionproof, CI 1 group D, CI 2 groups F&G, three phase, 230/460 or 575 volts IG IntelliGear variable speed for 3-ph/230V, or 3-ph/460V power supplies, NEMA 4/12 Denotes 6-pole (1200 rpm) motor. Single phase motor has 184T frame. D-51

52 Gearmotors 5 HP General Specifications: Totally enclosed, 60 hertz, 40 C ambient, continuous duty. Series Output RPM AGMA Class Service Factor Output Torque in-lb Nominal Ratio Gear Frame Size Motor Std. Motor Types 446 I, II, III T T, S, C, X, IG 354 I, II, III T T, S, C, X, IG 296 I, II, III T T, S, C, X, IG 250 I, II, III T T, S, C, X, IG 240 I T T, S, C, X, IG 235 I, II, III T T, S, C, X, IG 211 I, II, III T T, C, X 208 I, II, III T T, S, C, X, IG 200 I, II, III T T, S, C, X, IG 196 I, II T T, C, X 190 I T T, S, C, X, IG 188 I, II T T, S, C, X, IG 186 I, II, III T T, C, X 173 I, II, III T T, S, C, X, IG 165 I, II T T, S, C, X, IG 164 I, II, III T T, C, X 158 I, II, III T T, S, C, X, IG 156 I, II T T, C, X 154 I, II, III T T, C, X 142 I, II T T, S, C, X, IG 142 I, II, III T T, S, C, X, IG 138 I, II T T, C, X 134 I, II T T, S, C, X, IG 132 I, II, III T T, C, X 124 I, II T T, C, X 124 I, II, III T T, S, C, X, IG 117 I, II T T, S, C, X, IG 115 I, II, III T T, C, X 112 I, II, III T T, S, C, X, IG 109 I T T, C, X 106 I T T, S, C, X, IG 105 I, II, III T T, C, X 98 I, II, III T T, S, C, X, IG 94 I T T, S, C, X, IG 94 I, II, III T T, C, X 89 I T T, C, X 87 I, II, III T T, S, C, X, IG 84 I T T, S, C, X, IG 82 I, II, III T T, C, X 80 I, II T T, S, C, X, IG Standard Motor Types (see page D-15 for product codes) T TEFC, three phase, /460 or 575 volts S TEFC, single phase, 230 volts C Corro-Duty, three phase, 230/460 or 575 volts X Explosionproof, CI 1 group D, CI 2 groups F&G, three phase, 230/460 or 575 volts IG IntelliGear variable speed for 3-ph/230V, or 3-ph/460V power supplies, NEMA 4/12 Denotes 6-pole (1200 rpm) motor. D-52

53 Gearmotors 5 HP (Continued) General Specifications: Totally enclosed, 60 hertz, 40 C ambient, continuous duty. Output RPM AGMA Class Service Factor Output Torque in-lb Nominal Ratio Gear Frame Size Motor Std. Motor Types 80 I, II, III T T, S, C, X, IG 78 I T T, C, X 75 I, II, III T T, C, X 74 I T T, S, C, X, IG 74 I, II T T, C, X 72 I, II T T, S, C, X, IG 70 I T T, C, X 70 I, II, III T T, S, C, X, IG 67 I, II, III T T, C, X 65 I, II T T, C, X 65 I, II, III T T, S, C, X, IG 64 I, II T T, S, C, X, IG 60 I, II, III T T, C, X 57 I, II T T, C, X 56 I T T, S, C, X, IG 56 I, II, III T T, S, C, X, IG 53 I T T, C, X 53 I, II, III T T, C, X 52 I T T, S, C, X, IG 52 I, II, III T T, S, C, X, IG 48 I T T, C, X 47 I, II, III T T, S, C, X, IG 46 I T T, S, C, X, IG 46 I, II, III T T, C, X 43 I, II, III T T, C, X 42 I T T, C, X 42 I, II, III T T, S, C, X, IG 40 I T T, S, C, X, IG 37 I, II T T, C, X 36 I, II, III T T, C, X 35 I, II T T, S, C, X, IG 35 I, II, III T T, S, C, X, IG 34 I, II T T, C, X 33 I, II T T, S, C, X, IG 33 I, II, III T T, C, X 31 I, II T T, C, X 31 I, II, III T T, S, C, X, IG 29 I, II T T, S, C, X, IG 29 I, II, III T T, S, C, X, IG 28 I, II T T, C, X Series Standard Motor Types (see page D-15 for product codes) T TEFC, three phase, /460 or 575 volts S TEFC, single phase, 230 volts C Corro-Duty, three phase, 230/460 or 575 volts X Explosionproof, CI 1 group D, CI 2 groups F&G, three phase, 230/460 or 575 volts IG IntelliGear variable speed for 3-ph/230V, or 3-ph/460V power supplies, NEMA 4/12 For tapered bushed (00B) output shaft configuration with 35.5:1 ratio 26, gear frame must be 2603 instead of Denotes 6-pole (1200 rpm) motor. D-53

54 Series Gearmotors 5 HP (Continued) General Specifications: Totally enclosed, 60 hertz, 40 C ambient, continuous duty. Output RPM AGMA Class Service Factor Output Torque in-lb Nominal Ratio Gear Frame Size Motor Std. Motor Types 27 I, II, III T T, S, C, X, IG 26 I T T, S, C, X, IG 24 I T T, C, X 23 I T T, S, C, X, IG 23 I, II T T, S, C, X, IG 23 I, II, III T T, C, X 22 I T T, C, X 22 I, II, III T T, S, C, X, IG 21 I, II T T, S, C, X, IG 20 I T T, S, C, X, IG 20 I, II, III T T, C, X 19 I T T, C, X 19 I, II T T, C, X 19 I, II, III T T, S, C, X, IG 18 I T T, S, C, X, IG 18 I, II T T, S, C, X, IG 18 I, II, III T T, C, X 17 I T T, S, C, X, IG 17 I, II, III T T, S, C, X, IG 16 I T T, C, X 16 I, II, III T T, S, C, X, IG 15 I T T, S, C, X, IG 14 I T T, C, X 14 I, II, III T T, S, C, X, IG 13 I T T, S, C, X, IG 13 I, II T T, S, C, X, IG 12 I T T, C, X 11 I, II T T, S, C, X, IG 10.5 I, II T T, C, X 10.1 I, II T T, S, C, X, IG 9.3 I, II T T, C, X 8.7 I T T, S, C, X, IG 8.4 I T T, C, X 7.8 I A 184T T, S, C, X, IG 7.4 I T T, C, X 6.8 I A 184T T, S, C, X, IG 6.7 I T T, C, X Standard Motor Types (see page D-15 for product codes) T TEFC, three phase, /460 or 575 volts S TEFC, single phase, 230 volts C Corro-Duty, three phase, 230/460 or 575 volts X Explosionproof, CI 1 group D, CI 2 groups F&G, three phase, 230/460 or 575 volts IG IntelliGear variable speed for 3-ph/230V, or 3-ph/460V power supplies, NEMA 4/12 Denotes 6-pole (1200 rpm) motor. D-54

55 Gearmotors 7 1/2 HP General Specifications: Totally enclosed, 60 hertz, 40 C ambient, continuous duty. Output RPM AGMA Class Service Factor Output Torque in-lb Nominal Ratio Gear Frame Size Motor Std. Motor Types 446 I, II T T, C, X, IG 365 I, II, III T T, C, X, IG 354 I, II T T, C, X, IG 319 I, II, III T T, C, X, IG 296 I, II T T, C, X, IG 281 I, II, III T T, C, X, IG 250 I, II T T, C, X, IG 247 I, II, III T T, C, X, IG 242 I, II, III T T, C, X 235 I, II T T, C, X, IG 232 I, II, III T T, C, X, IG 211 I, II, III T T, C, X 208 I T T, C, X, IG 200 I, II, III T T, C, X, IG 188 I T T, C, X, IG 186 I, II, III T T, C, X 173 I, II, III T T, C, X, IG 165 I T T, C, X, IG 164 I, II, III T T, C, X 158 I, II, III T T, C, X, IG 154 I, II, III T T, C, X 142 I T T, C, X, IG 142 I, II, III T T, C, X, IG 138 I, II, III T T, C, X 134 I T T, C, X, IG 133 I, II, III T T, C, X, IG 132 I, II T T, C, X 124 I, II T T, C, X, IG 123 I, II, III T T, C, X 115 I, II T T, C, X 114 I, II, III T T, C, X, IG 112 I, II T T, C, X, IG 109 I, II, III T T, C, X 105 I, II T T, C, X 102 I, II, III T T, C, X, IG 98 I, II T T, C, X, IG Series Standard Motor Types (see page D-15 for product codes) T TEFC, three phase, /460 or 575 volts C Corro-Duty, three phase, 230/460 or 575 volts X Explosionproof, CI 1 group D, CI 2 groups F&G, three phase, 230/460 or 575 volts IG IntelliGear variable speed for 3-ph/460V power supplies, NEMA 4/12 Denotes 6-pole (1200 rpm) motor. D-55

56 Series Gearmotors 7 1/2 HP (Continued) General Specifications: Totally enclosed, 60 hertz, 40 C ambient, continuous duty. Output RPM AGMA Class Service Factor Output Torque in-lb Nominal Ratio Gear Frame Size Motor Std. Motor Types 97 I, II, III T T, C, X 94 I, II T T, C, X 90 I, II, III T T, C, X, IG 88 I, II, III T T, C, X 87 I, II T T, C, X, IG 82 I T T, C, X 80 I T T, C, X, IG 80 I, II, III T T, C, X, IG 75 I, II T T, C, X 74 I T T, C, X 74 I, II, III T T, C, X 72 I T T, C, X, IG 70 I, II T T, C, X, IG 68 I, II, III T T, C, X, IG 67 I, II T T, C, X 66 I, II, III T T, C, X 65 I, II T T, C, X, IG 64 I T T, C, X, IG 63 I, II, III T T, C, X, IG 60 I, II T T, C, X 59 I, II, III T T, C, X 56 I, II T T, C, X, IG 54 I, II, III T T, C, X, IG 52 I, II T T, C, X, IG 52 I, II, III T T, C, X 49 I, II, III T T, C, X, IG 47 I, II T T, C, X, IG 45 I, II, III T T, C, X 44 I, II, III T T, C, X, IG 42 I T T, C, X, IG 42 I, II T T, C, X 41 I, II, III T T, C, X 40 I, II, III T T, C, X, IG 37 I T T, C, X 37 I, II, III T T, C, X 36 I, II T T, C, X 35 I T T, C, X, IG 35 I, II, III T T, C, X, IG 34 I T T, C, X 34 I, II T T, C, X Standard Motor Types (see page D-15 for product codes) T TEFC, three phase, /460 or 575 volts C Corro-Duty, three phase, 230/460 or 575 volts X Explosionproof, CI 1 group D, CI 2 groups F&G, three phase, 230/460 or 575 volts IG IntelliGear variable speed for 3-ph/460V power supplies, NEMA 4/12 28:1, 31.5:1, and 35.5:1 ratios of 2602 are not available with the tapered bushed (00B) output shaft configuration. For 31.5:1 and 35.5:1 ratios, gear frame 2603 may be used for 00B. Denotes 6-pole (1200 rpm) motor. D-56

57 Gearmotors 7 1/2 HP (Continued) General Specifications: Totally enclosed, 60 hertz, 40 C ambient, continuous duty. Output RPM AGMA Class Service Factor Output Torque in-lb Nominal Ratio Gear Frame Size Motor Std. Motor Types 33 I T T, C, X, IG 33 I, II, III T T, C, X 31 I T T, C, X 31 I, II, III T T, C, X, IG 30 I, II T T, C, X 29 I, II T T, C, X, IG 29 I, II, III T T, C, X 28 I, II, III T T, C, X, IG 27 I, II T T, C, X, IG 27 I, II, III T T, C, X 25 I, II, III T T, C, X, IG 24 I T T, C, X 23 I T T, C, X, IG 23 I, II, III T T, C, X 22 I T T, C, X 22 I, II, III T T, C, X, IG 21 I T T, C, X, IG 20 I, II, III T T, C, X 19 I T T, C, X 19 I, II T T, C, X, IG 18 I, II T T, C, X 17 I, II T T, C, X, IG 16 I, II T T, C, X, IG 14 I, II T T, C, X, IG 13 I T T, C, X, IG 11 I T T, C, X, IG 10.5 I T T, C, X 10.1 I T T, C, X, IG Series Standard Motor Types (see page D-15 for product codes) T TEFC, three phase, /460 or 575 volts C Corro-Duty, three phase, 230/460 or 575 volts X Explosionproof, CI 1 group D, CI 2 groups F&G, three phase, 230/460 or 575 volts IG IntelliGear variable speed for 3-ph/460V power supplies, NEMA 4/12 28:1, 31.5:1, and 35.5:1 ratios of 2602 are not available with the tapered bushed (00B) output shaft configuration. For 31.5:1 and 35.5:1 ratios, gear frame 2603 may be used for 00B. Denotes 6-pole (1200 rpm) motor. D-57

58 Series Gearmotors 10 HP General Specifications: Totally enclosed, 60 hertz, 40 C ambient, continuous duty. Output RPM AGMA Class Service Factor Output Torque in-lb Nominal Ratio Gear Frame Size Motor Std. Motor Types 446 I, II T T, C, X, IG 365 I, II, III T T, C, X, IG 354 I T T, C, X, IG 319 I, II, III T T, C, X, IG 296 I T T, C, X, IG 281 I, II, III T T, C, X, IG 250 I T T, C, X, IG 247 I, II, III T T, C, X, IG 242 I, II, III T T, C, X 235 I T T, C, X, IG 232 I, II, III T T, C, X, IG 211 I, II T T, C, X 208 I T T, C, X, IG 200 I, II, III T T, C, X, IG 196 I, II, III T T, C, X 185 I, II, III T T, C, X, IG 173 I, II T T, C, X, IG 165 I, II, III T T, C, X, IG 164 I, II T T, C, X 160 I, II, III T T, C, X 158 I, II T T, C, X, IG 154 I, II, III T T, C, X 146 I, II, III T T, C, X, IG 142 I, II T T, C, X, IG 138 I, II, III T T, C, X 133 I, II, III T T, C, X, IG 132 I, II T T, C, X 124 I, II T T, C, X, IG 117 I, II, III T T, C, X 115 I T T, C, X 114 I, II T T, C, X, IG 112 I T T, C, X, IG Standard Motor Types (see page D-15 for product codes) T TEFC, three phase, /460 or 575 volts C Corro-Duty, three phase, 230/460 or 575 volts X Explosionproof, CI 1 group D, CI 2 groups F&G, three phase, 230/460 or 575 volts IG IntelliGear variable speed for 3-ph/460V power supplies, NEMA 4/12 Denotes 6-pole (1200 rpm) motor. D-58

59 Gearmotors 10 HP (Continued) General Specifications: Totally enclosed, 60 hertz, 40 C ambient, continuous duty. Output RPM AGMA Class Service Factor Output Torque in-lb Nominal Ratio Gear Frame Size Motor Std. Motor Types 111 I, II, III T T, C, X, IG 109 I, II T T, C, X 105 I T T, C, X 104 I, II, III T T, C, X 102 I, II T T, C, X, IG 99 I, II, III T T, C, X, IG 98 I T T, C, X, IG 97 I, II T T, C, X 94 I T T, C, X 94 I, II, III T T, C, X 90 I, II T T, C, X, IG 89 I, II, III T T, C, X, IG 88 I, II T T, C, X 87 I T T, C, X, IG 82 I T T, C, X 81 I, II, III T T, C, X 80 I, II T T, C, X, IG 78 I, II, III T T, C, X, IG 75 I, II T T, C, X 74 I, II, III T T, C, X 70 I, II T T, C, X, IG 68 I, II, III T T, C, X, IG 67 I T T, C, X 66 I, II, III T T, C, X 65 I T T, C, X, IG 63 I, II, III T T, C, X, IG 60 I T T, C, X 59 I, II, III T T, C, X 57 I, II, III T T, C, X, IG 56 I T T, C, X, IG 54 I, II T T, C, X, IG 52 I T T, C, X, IG Series Standard Motor Types (see page D-15 for product codes) T TEFC, three phase, /460 or 575 volts C Corro-Duty, three phase, 230/460 or 575 volts X Explosionproof, CI 1 group D, CI 2 groups F&G, three phase, 230/460 or 575 volts IG IntelliGear variable speed for 3-ph/460V power supplies, NEMA 4/12 28:1, 31.5:1, and 35.5:1 ratios of 2602 are not available with the tapered bushed (00B) output shaft configuration. For 31.5:1 and 35.5:1 ratios, gear frame 2603 may be used for 00B. Denotes 6-pole (1200 rpm) motor. D-59

60 Series Gearmotors 10 HP (Continued) General Specifications: Totally enclosed, 60 hertz, 40 C ambient, continuous duty. Output RPM AGMA Class Service Factor Output Torque in-lb Nominal Ratio Gear Frame Size Motor Std. Motor Types 52 I, II T T, C, X 50 I, II, III T T, C, X 49 I, II, III T T, C, X, IG 47 I T T, C, X, IG 47 I, II, III T T, C, X 46 I T T, C, X 45 I, II T T, C, X 44 I, II, III T T, C, X, IG 43 I T T, C, X 42 I T T, C, X, IG 42 I, II T T, C, X 41 I, II, III T T, C, X 40 I, II, III T T, C, X, IG 37 I, II, III T T, C, X 36 I, II T T, C, X 35 I, II, III T T, C, X, IG 34 I T T, C, X 33 I, II, III T T, C, X 31 I, II, III T T, C, X, IG 30 I T T, C, X 29 I T T, C, X, IG 29 I, II, III T T, C, X 28 I, II, III T T, C, X, IG 27 I T T, C, X, IG 27 I, II, III T T, C, X 25 I, II T T, C, X, IG 23 I, II T T, C, X 22 I, II T T, C, X, IG 20 I, II T T, C, X 19 I, II T T, C, X, IG 18 I, II T T, C, X 17 I T T, C, X, IG 16 I T T, C, X, IG 14 I T T, C, X, IG 13 I T T, C, X, IG Standard Motor Types (see page D-15 for product codes) T TEFC, three phase, /460 or 575 volts C Corro-Duty, three phase, 230/460 or 575 volts X Explosionproof, CI 1 group D, CI 2 groups F&G, three phase, 230/460 or 575 volts IG IntelliGear variable speed for 3-ph/460V power supplies, NEMA 4/12 28:1, 31.5:1, and 35.5:1 ratios of 2602 are not available with the tapered bushed (00B) output shaft configuration. For 31.5:1 and 35.5:1 ratios, gear frame 2603 may be used for 00B. Denotes 6-pole (1200 rpm) motor. D-60

61 Gearmotors 15 HP General Specifications: Totally enclosed, 60 hertz, 40 C ambient, continuous duty. Output RPM AGMA Class Service Factor Output Torque in-lb Nominal Ratio Gear Frame Size Motor Std. Motor Types 365 I, II, III T T, C, X 319 I, II T T, C, X 296 I, II, III T T, C, X 281 I, II, III T T, C, X 247 I, II T T, C, X 242 I, II, III T T, C, X 232 I, II, III T T, C, X 208 I, II T T, C, X 200 I, II T T, C, X 192 I, II, III T T, C, X 185 I, II T T, C, X 177 I, II, III T T, C, X 173 I T T, C, X 165 I, II T T, C, X 158 I T T, C, X 156 I, II, III T T, C, X 146 I, II T T, C, X 142 I T T, C, X 141 I, II, III T T, C, X 133 I, II T T, C, X 124 I T T, C, X 122 I, II, III T T, C, X 114 I T T, C, X 111 I, II, III T T, C, X 102 I T T, C, X 99 I, II, III T T, C, X 90 I T T, C, X 89 I, II, III T T, C, X Series Standard Motor Types (see page D-15 for product codes) T TEFC, three phase, /460 or 575 volts C Corro-Duty, three phase, 230/460 or 575 volts X Explosionproof, CI 1 group D, CI 2 groups F&G, three phase, 230/460 or 575 volts D-61

62 Gearmotors 15 HP (Continued) General Specifications: Totally enclosed, 60 hertz, 40 C ambient, continuous duty. Output RPM AGMA Class Service Factor Output Torque in-lb Nominal Ratio Gear Frame Size Motor Std. Motor Types 80 I T T, C, X 78 I, II T T, C, X 76 I, II, III T T, C, X 70 I, II, III T T, C, X 68 I, II T T, C, X 63 I, II T T, C, X 62 I, II, III T T, C, X 57 I, II, III T T, C, X 54 I T T, C, X 51 I T T, C, X 49 I, II, III T T, C, X 45 I T T, C, X 44 I, II, III T T, C, X 41 I T T, C, X 40 I, II T T, C, X 35 I, II T T, C, X 31 I, II T T, C, X 28 I, II T T, C, X 25 I T T, C, X 22 I T T, C, X 19 I T T, C, X Series Standard Motor Types (see page D-15 for product codes) T TEFC, three phase, /460 or 575 volts C Corro-Duty, three phase, 230/460 or 575 volts X Explosionproof, CI 1 group D, CI 2 groups F&G, three phase, 230/460 or 575 volts 28:1, 31.5:1, and 35.5:1 ratios of 2602 are not available with the tapered bushed (00B) output shaft configuration. For 31.5:1 and 35.5:1 ratios, gear frame 2603 may be used for 00B. D-62

63 Gearmotors 20 HP General Specifications: Totally enclosed, 60 hertz, 40 C ambient, continuous duty. Output RPM AGMA Class Service Factor Output Torque in-lb Nominal Ratio Gear Frame Size Motor Std. Motor Types 365 I, II T T, C, X 338 I, II, III T T, C, X 319 I T T, C, X 296 I, II, III T T, C, X 281 I, II T T, C, X 270 I, II, III T T, C, X 247 I T T, C, X 242 I, II, III T T, C, X 232 I, II T T, C, X 216 I, II, III T T, C, X 208 I, II T T, C, X 200 I T T, C, X 192 I, II, III T T, C, X 185 I T T, C, X 177 I, II, III T T, C, X 165 I T T, C, X 156 I, II, III T T, C, X 146 I T T, C, X 141 I, II, III T T, C, X 133 I T T, C, X 122 I, II, III T T, C, X 114 I T T, C, X 112 I, II, III T T, C, X 111 I, II T T, C, X 99 I, II T T, C, X 96 I, II, III T T, C, X 89 I, II T T, C, X 86 I, II, III T T, C, X 78 I, II T T, C, X 76 I, II, III T T, C, X 70 I, II, III T T, C, X 68 I T T, C, X 63 I T T, C, X 62 I, II, III T T, C, X 57 I, II T T, C, X 49 I, II T T, C, X 44 I, II T T, C, X 40 I, II T T, C, X 35 I T T, C, X 31 I T T, C, X 28 I T T, C, X Series Standard Motor Types (see page D-15 for product codes) T TEFC, three phase, /460 or 575 volts C Corro-Duty, three phase, 230/460 or 575 volts X Explosionproof, CI 1 group D, CI 2 groups F&G, three phase, 230/460 or 575 volts 28:1, 31.5:1, and 35.5:1 ratios of 2602 are not available with the tapered bushed (00B) output shaft configuration. For 31.5:1 and 35.5:1 ratios, gear frame 2603 may be used for 00B. D-63

64 Series Gearmotors 25 HP General Specifications: Totally enclosed, 60 hertz, 40 C ambient, continuous duty. Output RPM AGMA Class Service Factor Output Torque in-lb Nominal Ratio Gear Frame Size Motor Std. Motor Types 365 I, II T T, C, X 338 I, II, III T T, C, X 296 I, II, III T T, C, X 281 I T T, C, X 270 I, II, III T T, C, X 242 I, II, III T T, C, X 232 I T T, C, X 216 I, II, III T T, C, X 208 I T T, C, X 192 I, II, III T T, C, X 185 I T T, C, X 177 I, II, III T T, C, X 165 I T T, C, X 156 I, II, III T T, C, X 141 I, II, III T T, C, X 124 I, II, III T T, C, X 122 I, II T T, C, X 112 I, II, III T T, C, X 111 I, II T T, C, X 99 I, II T T, C, X 96 I, II, III T T, C, X 89 I T T, C, X 86 I, II T T, C, X 76 I, II T T, C, X 70 I, II T T, C, X 62 I, II T T, C, X 57 I, II T T, C, X 49 I T T, C, X 44 I T T, C, X 40 I T T, C, X 35 I T T, C, X Standard Motor Types (see page D-15 for product codes) T TEFC, three phase, /460 or 575 volts C Corro-Duty, three phase, 230/460 or 575 volts X Explosionproof, CI 1 group D, CI 2 groups F&G, three phase, 230/460 or 575 volts 28:1, 31.5:1, and 35.5:1 ratios of 2602 are not available with the tapered bushed (00B) output shaft configuration. For 31.5:1 and 35.5:1 ratios, gear frame 2603 may be used for 00B. D-64

65 Gearmotors 30 HP General Specifications: Totally enclosed, 60 hertz, 40 C ambient, continuous duty. Output RPM AGMA Class Service Factor Output Torque in-lb Nominal Ratio Frame Size Std. Motor Types Gear Motor 365 I T T, C, X 338 I, II, III T T, C, X 296 I, II, III T T, C, X 281 I T T, C, X 270 I, II, III T T, C, X 242 I, II, III T T, C, X 232 I T T, C, X 216 I, II, III T T, C, X 208 I T T, C, X 192 I, II, III T T, C, X 177 I, II, III T T, C, X 156 I, II T T, C, X 156 I, II, III T T, C, X 141 I, II T T, C, X 136 I, II, III T T, C, X 124 I, II, III T T, C, X 122 I, II T T, C, X 112 I, II, III T T, C, X 111 I T T, C, X 99 I T T, C, X 96 I, II T T, C, X 89 I T T, C, X 86 I, II T T, C, X 76 I, II T T, C, X 70 I, II T T, C, X 62 I T T, C, X 57 I T T, C, X 49 I T T, C, X 44 I T T, C, X 40 I T T, C, X Series Standard Motor Types (see page D-15 for product codes) T TEFC, three phase, /460 or 575 volts C Corro-Duty, three phase, 230/460 or 575 volts X Explosionproof, CI 1 group D, CI 2 groups F&G, three phase, 230/460 or 575 volts 28:1, 31.5:1, and 35.5:1 ratios of 2602 are not available with the tapered bushed (00B) output shaft configuration. For 31.5:1 and 35.5:1 ratios, gear frame 2603 may be used for 00B. D-65

66 Gearmotors 40 HP General Specifications: Totally enclosed, 60 hertz, 40 C ambient, continuous duty. Output RPM AGMA Class Service Factor Output Torque in-lb Nominal Ratio Gear Frame Size Motor Std. Motor Types 338 I, II T T, C, X 296 I, II T T, C, X 270 I, II T T, C, X 247 I, II, III T T, C, X 242 I, II T T, C, X 219 I, II, III T T, C, X 216 I, II T T, C, X 193 I, II, III T T, C, X 192 I, II T T, C, X 177 I, II T T, C, X 170 I, II T T, C, X 156 I, II T T, C, X 156 I, II T T, C, X 141 I T T, C, X 136 I, II T T, C, X 124 I, II T T, C, X 122 I T T, C, X 112 I, II T T, C, X 96 I T T, C, X 86 I T T, C, X 76 I T T, C, X 70 I T T, C, X 62 I T T, C, X Series Standard Motor Types (see page D-15 for product codes) T TEFC, three phase, 230/460 or 575 volts C Corro-Duty, three phase, 230/460 or 575 volts X Explosionproof, CI 1 group D, CI 2 groups F&G, three phase, 230/460 or 575 volts 28:1 ratio 2602 is NOT available with the tapered bushed (00B) output shaft configuration. D-66

67 Gearmotors 50 HP General Specifications: Totally enclosed, 60 hertz, 40 C ambient, continuous duty. Output RPM AGMA Class Service Factor Output Torque in-lb Nominal Ratio Gear Frame Size Motor Std. Motor Types 338 I T T, C, X 296 I T T, C, X 270 I T T, C, X 247 I, II T T, C, X 242 I T T, C, X 219 I, II T T, C, X 216 I T T, C, X 193 I, II T T, C, X 192 I T T, C, X 177 I T T, C, X 170 I, II T T, C, X 156 I T T, C, X 156 I, II T T, C, X 141 I T T, C, X 136 I T T, C, X 124 I T T, C, X 112 I T T, C, X 96 I T T, C, X 86 I T T, C, X 60 HP General Specifications: Totally enclosed, 60 hertz, 40 C ambient, continuous duty. Output RPM AGMA Class Service Factor Output Torque in-lb Nominal Ratio Gear Frame Size Motor Std. Motor Types 247 I, II T T, C 219 I, II T T, C 193 I T T, C 170 I T T, C 156 I T T, C 136 I T T, C 124 I T T, C 112 I T T, C Series Standard Motor Types (see page D-15 for product codes) T TEFC, three phase, 230/460 or 575 volts C Corro-Duty, three phase, 230/460 or 575 volts X Explosionproof, CI 1 group D, CI 2 groups F&G, three phase, 230/460 or 575 volts D-67

68 Gearmotor Dimensions 31 Double Reduction 40C Finished Bore Face Mount AD ØP XK XM HY AH AB AC YA G 15 F O P2 XN AK HZ AA Conduit Size B BB ØAJ A D BF 4 Holes M EH Key U UF UY VH VG Output Shaft Gear Frame A B D HY HZ XM XN YA C Face Gear Frame AH AJ AK BB BF M8X12 Tie Rod 5 Gear F G Frame Min. Max Series Output Shaft Gear Frame EH U 2 UF UY VG VH Key 4 M /4 Sq. 7/16-14 Motor Motor Gear Frame Type 3 Frame P P2 O AA AB AC AD XK 48 T T T/145T T TY T T/184T T All rough casting dimensions may vary by up to 0.25" due to casting variations. 2 Output finished bore tolerances (diameter U ): "/ " for all diameters. 3 Motor dimensions shown are for Type T three phase TEFC motors. For dimensions of other motor types, see pages D-86 or D Key to be supplied by others. 5 Refer to Mounting Accessories on page D-22 for details of Silent-Bloc and Tie Rod kits. D-68

69 Gearmotor Dimensions Double/Triple Reduction 40C Finished Bore Face Mount AD ØP XK XM HY AH HQ AB AC YA G 15 F O P2 XN AA Conduit Size H - 8 Holes EV 2F B HZ HB AK HA BB BA A HF D M VH EH VG U UF UY Output Shaft Key ØAJ 45 Typ. BF 4 Holes Gear Frame Size Typ. ØAJ BF 6 Holes Gear Frame Size - 33 Gear Frame A B D 2F H EV HA HB HF HQ HY HZ XM XN YA M8X M16X M10X M24X C Face Tie Rod 5 Gear Frame AH AJ AK BA BB BF M8X M10X18 Gear Frame F Min. Max. G Output Shaft Gear Frame EH U 2 UF UY VG VH Key 4 M 3202/ /4 Sq. 7/ / /16 Sq. 1/ /8 Sq. 5/8-11 Motor Frame Motor Gear Type 3 Frame P P2 O AA AB AC AD XK 56 T T T/145T T T TY T T T/184T T T T T T T T T T T T T Series 1 All rough casting dimensions may vary by up to 0.25" due to casting variations. 2 Output finished bore tolerances (diameter U ): "/ " for all diameters. 3 Motor dimensions shown are for Type T three phase TEFC motors. For dimensions of other motor types, see pages D-86 or D Key to be supplied by others. 5 Refer to Mounting Accessories on page D-22 for details of Silent-Bloc and Tie Rod kits. D-69

70 Gearmotor Dimensions Double/Triple Reduction 40C Finished Bore Face Mount AD ØP XK XM HY AH HQ AB AC YA G 15 F 15 P2 XN O HZ HB AK HF H - 8 Holes HA D M VH EH VG U UF Output Shaft UY EV Key 2F B BB BA ØAJ BF 6 Holes Gear Frame Size - 34 A BF 6 Holes 60 ØAJ Gear Frame Size - 35 XM Gear Frame A B D 2F H EV HA HB HF HQ HY HZ XN YA 182T-215T 254T-286T 324T-326T M16X M24X M16X M24X C Face Tie Rod 5 Gear Frame AH AJ AK BA BB BF M12X M12X20 Gear Frame F Min. Max. G Series Output Shaft Gear Frame EH U 2 UF UY VG VH Key 4 M /2 Sq. 5/ /8 Sq. 3/4-10 Motor Frame Motor Gear Type 3 Frame P P2 O AA AB AC AD XK 182T/184T T T T T T T T T T T T T T T T T T T T T T/326T T All rough casting dimensions may vary by up to 0.25" due to casting variations. 2 Output finished bore tolerances (diameter U ): "/ " for all diameters. 3 Motor dimensions shown are for Type T three phase TEFC motors. For dimensions of other motor types, see pages D-86 or D-87. D-70 4 Key to be supplied by others. 5 Refer to Mounting Accessories on page D-22 for details of Silent-Bloc and Tie Rod kits.

71 Gearmotor Dimensions 26 Double/Triple Reduction 00C Finished Bore Shaft Mount 40C Finished Bore Face Mount AD ØP XK XM HY AH HQ AB AC YA G 15 F 15 O XN P2 AA Conduit Size AK HZ HB Typ. HF HA H - 8 Holes EV 2F B BB BA A D BF 4 Holes M EH U UF UY Key VH VG Output Shaft XM Gear Frame A B D 2F H EV HA HB HF HQ HY HZ 182T- 213T- 254T- 324T- XN YA 184T 215T 286T 326T 364T M6X M30X C Face 5 Tie Rod 6 F Gear Frame AH AJ AK BA BB BF Gear Frame G Min. Max M16X Output Shaft Gear Frame EH U 2 UF UY VG VH Key 4 M /8 Sq. 5/8-11 Motor Frame Motor Gear Type 3 Frame P P2 O AA AB AC AD XK 182T/184T T T T T T T T T T T T T T T/326T T T T Series 1 All rough casting dimensions may vary by up to 0.25" due to casting variations. 2 Output finished bore tolerances (diameter U ): "/ " for all diameters. 3 Motor dimensions shown are for Type T three phase TEFC motors. For dimensions of other motor types, see pages D-86 or D Key to be supplied by others. 5 Face dimensions only apply to the 40C face mount units. 6 Refer to Mounting Accessories on page D-22 for details of Silent-Bloc and Tie Rod kits. D-71

72 Gearmotor Dimensions Combined (4-6 Reduction Stages) 40C Finished Bore Face Mount AD ØP XK XM HY AH HQ AB AC YA G 15 F 15 P2 XN O AA Conduit Size HZ HB AK HA HF D H - 8 Holes EV 2F B BB BA A M VH EH VG U UF UY Output Shaft Key ØAJ 45 Typ. BF 4 Holes Gear Frame Size - 32 ØAJ Typ. BF 6 Holes Gear Frame Size - 33 ØAJ BF 6 Holes Gear Frame Size - 34 Gear Frame A B D 2F H EV HA HB HF HQ HY HZ XM 4 Red. 5-6 Red. XN YA M8X M16X M10X M24X M16X M24X Series 40C Face Tie Rod 5 Gear Frame AH AJ AK BA BB BF M8X M10X M12X22 Output Shaft Gear Frame F Min. Max. G Gear Frame EH U 2 UF UY VG VH Key 4 M 3202/ /4 Sq. 7/ / /16 Sq. 1/ /8 Sq. 5/ /2 Sq. 5/8-11 Motor Frame T/145T 145TY Motor Gear Type 3 Frame P P2 O AA AB AC AD XK T T T T T T T T T All rough casting dimensions may vary by up to 0.25" due to casting variations. 2 Output finished bore tolerances (diameter U ): "/ " for all diameters. 3 Motor dimensions shown are for Type T three phase TEFC motors. For dimensions of other motor types, see pages D-86 or D Key to be supplied by others. D-72 5 Refer to Mounting Accessories on page D-22 for details of Silent-Bloc and Tie Rod kits.

73 Gearmotor Dimensions 35 and 26 Combined (4-6 Reduction Stages) 00C 6 Finished Bore Shaft Mount 40C Finished Bore Face Mount AD ØP XK XM HY AH HQ AB AC YA G 15 F 15 M O VH XN P2 AA Conduit Size H - 8 Holes EV 2F B HA AK BB BA HB HZ Typ. BF 4 Holes EH U Key Typ. UF UY BF VG 6 Holes 60 ØAJ BF Output Shaft Holes Gear Frame Size - 35 Gear Frame Size - 26 A HF D Gear Frame A B D 2F H EV HA HB HQ HF HY HZ XM XN YA M16X M24X A M16X M30X C Face 5 Tie Rod 7 Gear Frame AH AJ AK BA BB BF M12X22 26A M16X25 Gear Frame F Min. Max. G Output Shaft Gear Frame EH U 2 UF UY VG VH Key 4 M /8 Sq. 3/ A /8 Sq. 5/8-11 Motor Frame T/145T 145TY 182T/184T Motor Gear Type 3 Frame P P2 O AA AB AC AD XK T T 26A T T 26A T T 26A T T 26A Series 1 All rough casting dimensions may vary by up to 0.25" due to casting variations. 2 Output finished bore tolerances (diameter U ): "/ " for all diameters. 3 Motor dimensions shown are for Type T three phase TEFC motors. For dimensions of other motor types, see pages D-86 or D Key to be supplied by others. 5 Face dimensions only apply to the 40C face mount units is not available in 00C finished bore shaft mount version. 7 Refer to Mounting Accessories on page D-22 for details of Silent-Bloc and Tie Rod kits. D-73

74 Gearmotor Dimensions Double/Triple Reduction 50C/60C Finished Bore Flange Mount AD ØP XK XM HY AH HQ AB AC YA O BE XN P2 AA Conduit Size H - 8 Holes AK HB HA HZ ØAJ ØBD HF D EV 2F B BB BA A BF 4 Holes M EH Key U UF UY VH VG Output Shaft Gear Frame A B D 2F H AH EV HA HB HF HQ HY HZ XM XN YA M8X M16X M10X M24X Output Shaft Gear Frame EH U 2 UF UY VG VH Key 4 M 3202/ /4 Sq. 7/ / /16 Sq. 7/ /8 Sq. 5/8-11 Series Output Flange Gear Frame Flange Code AJ AK BA BB BD BE BF 60C C C C Motor Frame Motor Gear Type 3 Frame P P2 O AA AB AC AD XK 56 T T T/145T T T TY T T T/184T T T T T T T T T T T T T All rough casting dimensions may vary by up to 0.25" due to casting variations. 2 Output bore tolerances (diameter U ): "/ " for all diameters. D-74 3 Motor dimensions shown are for Type T three phase TEFC motors. For dimensions of other motor types, see pages D-86 or D Key to be supplied by others.

75 Gearmotor Dimensions Double/Triple Reduction 50C/60C Finished Bore Flange Mount AD ØP XK XM HY AH HQ AB AC YA O XN P2 BE HB HZ ØBD HF H - 8 Holes 2F B BA AK HA BB ØAJ A D BF 4 Holes M EH U UF UY Key VH VG Output Shaft Gear XM A B D 2F H AH EV HA HB HF HQ HY HZ Frame 182T-215T 254T-286T 324T-326T XN YA M16X M24X M16X M24X Output Shaft Gear Frame EH U 2 UF UY VG VH Key 4 M Sq. 5/ Sq. 3/4-10 Output Flange Gear Frame Flange Code AJ AK BA BB BD BE BF 60C C C Motor Frame Motor Gear Type 3 Frame P P2 O AA AB AC AD XK 182T/184T T T T T T T T T T T T T T T T T T T T T T/326T T Series 1 All rough casting dimensions may vary by up to 0.25" due to casting variations. 2 Output bore tolerances (diameter U ): "/ " for all diameters. 3 Motor dimensions shown are for Type T three phase TEFC motors. For dimensions of other motor types, see pages D-86 or D Key to be supplied by others. D-75

76 Gearmotor Dimensions 26 Double/Triple Reduction 50C Finished Bore Flange Mount AD ØP XK XM HY AH HQ AB AC YA BE O XN P2 AA Conduit Size HZ AK HB ØBD HF HA H - 8 Holes EV 2F B BB BA ØAJ A XK BF 8 Holes M EH Key U UF UY VH VG Output Shaft XM Gear A B D 2F H AH EV HA HB HF HQ HY HZ 182T- 213T- 254T- 324T- 364T XN YA Frame 184T 215T 286T 326T M6X M30X Output Shaft Gear Frame EH U 2 UF UY VG VH Key 4 M Sq. 5/8-11 Series Output Flange Gear Frame Flange Code AJ AK BA BB BD BE BF 26 50C Motor Frame Motor Gear Type 3 Frame P P2 O AA AB AC AD XK 182T/184T T T T T T T T T T T T T T T/326T T T T All rough casting dimensions may vary by up to 0.25" due to casting variations. 2 Output bore tolerances (diameter U ): "/ " for all diameters. D-76 3 Motor dimensions shown are for Type T three phase TEFC motors. For dimensions of other motor types, see pages D-86 or D Key to be supplied by others.

77 Gearmotor Dimensions Combined (4-6 Reduction Stages) 50C/60C Finished Bore Flange Mount XK XM AD ØP HY AH HQ AB AC YA BE O XN P2 AA Conduit Size HB HZ ØBD HF AK HA D H - 8 Holes EV 2F B BB BA ØAJ A BF 4 Holes M EH Key U UF UY VH VG Output Shaft Gear Frame A B D 2F H AH EV HA HB HF HQ HY HZ XM 4 Red. 5 Red. XN YA M8X M16X M10X M24X M16X M24X Output Shaft Gear Frame EH U 2 UF UY VG VH Key 4 M 3202/ /4 Sq. 7/ / /16 Sq. 7/ /8 Sq. 5/ /2 Sq. 5/8-11 Output Flange Gear Frame Flange Code AJ AK BA BB BD BE BF Motor Frame T/145T 145TY 60C C C C C C Motor Gear Type 3 Frame P P2 O AA AB AC AD XK T T T T T T T T T Series 1 All rough casting dimensions may vary by up to 0.25" due to casting variations. 2 Output bore tolerances (diameter U ): "/ " for all diameters. 3 Motor dimensions shown are for Type T three phase TEFC motors. For dimensions of other motor types, see pages D-86 or D Key to be supplied by others. D-77

78 Gearmotor Dimensions 35 and 26 Combined (4-6 Reduction Stages) 50C Finished Bore Flange Mount AD ØP XK XM HY AH HQ AB AC YA O XN P2 AA Conduit Size BE HZ HB AK ØBD HF HA H - 8 Holes EV 2F B BB BA ØAJ A D BF 8 Holes M EH U UF UY Key VH VG Output Shaft Gear Frame A B D 2F H AH EV HA HB HF HQ HY HZ XM XN YA M16X M24X A M16X M30X Output Shaft Gear Frame EH U 2 UF UY VG VH Key 4 M Sq. 3/ A Sq. 5/8-11 Series Output Flange Gear Frame Flange Code AJ AK BA BB BD BE BF 35 50C A 50C Motor Frame T/145T 145TY 182T/184T Motor Gear Type 3 Frame P P2 O AA AB AC AD XK T T 26A T T 26A T T 26A T T 26A All rough casting dimensions may vary by up to 0.25" due to casting variations. 2 Output bore tolerances (diameter U ): "/ " for all diameters. 3 Motor dimensions shown are for Type T three phase TEFC motors. For dimensions of other motor types, see pages D-86 or D Key to be supplied by others. D-78

79 Gearmotor Dimensions Double/Triple Reduction 00B Tapered Bushed Shaft Mount AD ØP XK XM HY HQ AB AC YA G 15 F O 15 XN P2 AA Conduit Size HB HZ HF H - 8 Holes EV 2F B XC BB BA HA MC A D Gear Frame A B D 2F H BA EV HA HB HF HQ HY HZ XM XN YA M8X M16X M10X M24X Output Shaft Gear Frame BB MC 4 XC Bushing Bores 2 Min. Max /4 1 7/ / /16 Tie Rod 7 Gear Frame F G Min. Max Motor Frame Motor Gear Type 3 Frame P P2 O AA AB AC AD XK 56 T T T/145T T T TY T T T/184T T T T T T T T T T T T T Series 1 All rough casting dimensions may vary by up to 0.25" due to casting variations. 2 Refer to pages D-18 and D-19 for a listing of all bushing bore sizes available in each gear frame. 3 Motor dimensions shown are for Type T three phase TEFC motors. For dimensions of other motor types, see pages D-86 or D The MC dimension shows spacing required to install or remove the bushing from the gear unit. 5 Bushing and dust cap can be installed opposite of how they are shown above. 6 Driven shaft entry can be from either side of gear housing. Refer to installation manual for requirements. 7 Refer to Mounting Accessories on page D-22 for details of Silent-Bloc and Tie Rod kits. D-79

80 Gearmotor Dimensions Double/Triple Reduction 00B Tapered Bushed Shaft Mount AD ØP XK XM HY HQ AB AC YA G 15 F O 15 XN P2 AA Conduit Size HB HZ HF H - 8 Holes EV 2F B XC BB BA HA MC A D XM Gear Frame A B D 2F H BA EV HA HB HF HQ HY HZ 182T- 215T 254T- 286T 324T- 326T XN YA M16X M24X M16X M24X Output Shaft Tie Rod 7 Gear Frame BB MC 4 XC Bushing Bores 2 Min. Max /8 2 7/ / /16 Gear Frame F Min. Max. G Series Motor Frame Motor Gear Type 3 Frame P P2 O AA AB AC AD XK 182T/184T T T T T T T T T T T T T T T T T T T T T T/326T T All rough casting dimensions may vary by up to 0.25" due to casting variations. 2 Refer to pages D-18 and D-19 for a listing of all bushing bore sizes available in each gear frame. 3 Motor dimensions shown are for Type T three phase TEFC motors. For dimensions of other motor types, see pages D-86 or D The MC dimension shows spacing required to install or remove D-80 the bushing from the gear unit. 5 Bushing and dust cap can be installed opposite of how they are shown above. 6 Driven shaft entry can be from either side of gear housing. Refer to installation manual for requirements. 7 Refer to Mounting Accessories on page D-22 for details of Silent-Bloc and Tie Rod kits.

81 Gearmotor Dimensions 26 Double/Triple Reduction 00B Tapered Bushed Shaft Mount AD ØP XK XM HY HQ AB AC YA G 15 F 15 O XN P2 AA Conduit Size HB HZ HF HA H - 8 Holes D EV 2F B XC BB BA A XM Gear Frame A B D 2F H BA EV HA HB HF HQ HY HZ 182T- 184T 213T- 215T 254T- 286T 324T- 326T 364T XN YA M6X M30X Output Shaft Bushing Bores Gear Frame BB XC 2 Min. Max /16 3 7/16 Tie Rod 4 F Gear Frame G Min. Max Motor Frame Motor Gear Type 3 Frame P P2 O AA AB AC AD XK 182T/184T T T T T T T T T T T T T T T/326T T T T Series 1 All rough casting dimensions may vary by up to 0.25" due to casting variations. 2 Refer to Tapered Bushings on page D-18 and D-19 for a listing of all bushing bore sizes available in each gear frame size. 3 Motor dimensions shown are for Type T three phase TEFC motors. For dimensions of other motor types, see pages D-86 or D Refer to Mounting Accessories on page D-22 for details of Silent-Bloc and Tie Rod kits. D-81

82 Gearmotor Dimensions Combined (4-6 Reduction Stages) 00B Tapered Bushed Shaft Mount XK XM ØP AD HY HQ AB AC YA G 15 F 15 O XN P2 AA Conduit Size HB HZ HF HA D H - 8 Holes EV 2F B XC BB BA MC A Gear Frame A B D 2F H BA EV HA HB HF HQ HY HZ XM 4 Red. 5-6 Red. XN YA M8X M16X M10X M24X M16X M24X Series Output Shaft Tie Rod 7 Gear Frame BB MC 4 XC Bushing Bores 2 Min. Max /4 1 7/ / / /8 2 7/16 Motor Frame T/145T 145TY Gear Frame F Min. Max. G Motor Gear Type 3 Frame P P2 O AA AB AC AD XK T T T T T T T T T All rough casting dimensions may vary by up to 0.25" due to casting variations. 2 Refer to Tapered Bushings on page D-18 and D-19 for a listing of all bushing bore sizes available in each gear frame size. 3 Motor dimensions shown are for Type T three phase TEFC motors. For dimensions of other motor types, see pages D-86 or D-87. D-82 4 The MC dimension shows spacing required to install or remove the bushing from the gear unit. 5 Bushing and dust cap can be installed opposite of how they are shown above. 6 Driven shaft entry can be from either side of gear housing. Refer to installation manual for requirements. 7 Refer to Mounting Accessories on page D-22 for details of Silent-Bloc and Tie Rod kits.

83 Gearmotor Dimensions 35 and 26 Combined (4-6 Reduction Stages) 00B Tapered Bushed Shaft Mount AD ØP XK XM HY HQ AB AC YA G 15 F 15 O XN P2 HB HZ HF AA Conduit Size HA H - 8 Holes D EV 2F B XC BB BA A Gear Frame A B D 2F H BA EV HA HB HF HQ HY HZ XM XN YA M16X M24X A M16X M30X Output Shaft Tie Rod 7 Gear Frame BB MC 4 XC Bushing Bores 2 Min. Max / /16 26A 1.68 N/A /16 3 7/16 Gear Frame F Min. Max. G Motor Frame T/145T 145TY 182T/184T Motor Gear Type 3 Frame P P2 O AA AB AC AD XK T T 26A T T 26A T T 26A T T 26A Series 1 All rough casting dimensions may vary by up to 0.25" due to casting variations. 2 Refer to Tapered Bushings on page D-18 and D-19 for a listing of all bushing bore sizes available in each gear frame size. 3 Motor dimensions shown are for Type T three phase TEFC motors. For dimensions of other motor types, see pages D-86 or D The MC dimension shows spacing required to install or remove the bushing from the gear unit. 5 Bushing and dust cap can be installed opposite of how they are shown for Driven shaft entry can be from either side of 35 gear housing. Refer to installation manual for requirements. 7 Refer to Mounting Accessories on page D-22 for details of Silent-Bloc and Tie Rod kits. D-83

84 O AD ØP P2 XN AA Conduit Size Gearmotor Dimensions Double/Triple Reduction 00S CEMA Screw Conveyor Drive XK XM BB AH S T ØJ U HQ AB AC YA L/2 4 Tapped Holes and Slots for "W" Dia. Trough End Fasteners. L HF D B XC Trough End L/2 L A S AH2 T ØJ T2 U Trough End Series Gear Frame A B D HF HQ XC XM TY 182T-215T 254T-256T 284T-286T 324T-326T XN YA BB M16X M24X M24X M24X Screw Conveyor Gear Frame Screw Dia U W J L S T T2 AH AH Motor Frame Motor Gear Type 3 Frame P P2 AA AB AC AD 56/143T/145T/145TY T T/184T T T/215T T T/256T T T/286T T T/326T T Motor Frame Motor O XK Type T T/145T T TY T T/184T T T T T T T T T T T T T T T/326T T All rough casting dimensions may vary by up to 0.25" due to casting variations. 2 Refer to pages D-20 and D-21 for the screw conveyor drive shafts, trough ends and other accessories available for each gear frame size. D-84 3 Motor dimensions shown are for Type T three phase TEFC motors. For dimensions of other motor types, see pages D-86 or D Thrust ratings for each gear frame size are listed on page D-20.

85 Gearmotor Dimensions Combined (4-6 Reduction Stages) 00S CEMA Screw Conveyor Drive AD ØP XK XM BB AH S T HQ AB AC YA 4 Tapped Holes and Slots for "W" Dia. Trough End Fasteners. P2 OXN AA Conduit Size ØJ U HF L/2 L D B XC Trough End AH2 S T L/2 L A ØJ T2 U Trough End Gear Frame A B D HF HQ XC XM 4 Red. 5 Red. XN YA BB M16X M24X M24X M24X Screw Conveyor Gear Frame Screw Dia. U W J L S T T2 AH AH Motor Frame Motor Gear Type 3 Frame P P2 AA AB AC AD 56/143T/145T/145TY T T/184T T Motor Frame Motor O XK Type T T/145T T TY T T/184T T Series 1 All rough casting dimensions may vary by up to 0.25" due to casting variations. 2 Refer to pages D-20 and D-21 for the screw conveyor drive shafts, trough ends and other accessories available for each gear frame size. 3 Motor dimensions shown are for Type T three phase TEFC motors. For dimensions of other motor types, see pages D-86 or D Thrust ratings for each gear frame size are listed on page D-20. D-85

86 Single Phase Gearmotor Alternate Motor Dimensions XK AB AD AC O BU P2 AF ØP AA Conduit Size Motor Frame HP O P P2 AA AB AC AD AF BU XK 1/6, 1/ / /3, 1/ / N/A /4, / /3, 1/ / N/A / / N/A T / N/A TY 1 1/2, / T 3, / N/A CorroDuty AC AB AD XK ØP Series P2 AF AA Conduit Size Motor Frame P P2 AA AB AC AD AF XK / T, 145T / TY / T, 184T / T, 215T T, 256T / T, 286T / XK = on 33 three stage and 26A combined. 2 XK will increase by.58" if used on 32 and 33 combined. D-86

87 Explosion Proof Gearmotor Alternate Motor Dimensions AB XK AC AD ØP AF P2 AA Conduit Size Motor Frame P P2 AA AB AC AD AF XK / T, 145T / T, 184T / T, 215T T, 256T / T, 286T / IntelliGear AB AC AW AZ AX AY AV AF O ØP P2 Motor Frame Controller O P P2 AB AC AD AF AV AW AX AY AZ XK 56 1, 1M T, 145T 1, 1M TY M T 2, 2M TY 2, 2M T, 184T T T AD XK Series Input Power Phase/Voltage Motor Max. Hz 0.33 to to 2 3 to to 10 1/115 1M 2M /230 1M 1M 1M 2M - - 3/ / XK = on 33 three stage and 26A combined. 2 XK will increase by.58" if used on 32 and 33 combined. D-87

88 Brake Dimensional Supplement A *E AC Brake with Type "T" and "S" Motor ØB G (Conduit Size) Motor Frame T / 145T Brake Torque (ft.-lbs.) A B E * G / / / / /2 182T / 184T /2 213T /2 215T /2 * Add E to the gearmotor length "XK" of the TEFC three phase motor type "T" shown in the gearmotor dimension prints. ZP AD1 E* AD2 DC FCR Brake with Type "T" Motor O ØP Motor Frame E* O P AA1 AA T/145T /4 NPT 1/2 NPT Series P2 AC AB AF2 AF AA1 Conduit Size (2 Holes, Opp. Each Other) Manual Release Lever Position AA2 Conduit Size (2 Holes, Opp. Each Other) Motor Frame AB AC AD1 AD2 AF T/145T Motor Frame AF2 P2 ZP T/145T * Add E to the gearmotor length "XK" of the TEFC three phase motor type "T" shown in the gearmotor dimension prints. D o'clock 3 o'clock 6 o'clock 9 o'clock See page D-17 for specifying the o clock position on orders.

89 Gearmotor Weights Approximate Shipping Weights - 40C Face Mounted Design with TEFC 3 Phase Motors Reduction Frame Stages T 145T 145TY 182T 184T 213T 215T 254T 256T 284T 286T 324T 326T Motor Options - Weight Adders Motor Types T 145T 145TY 182T 184T 213T 215T 254T 256T 284T 286T 324T 326T C Corro-Duty RO RO X Explosionproof RO - S Single Phase IG IntelliGear RO RO Gear Options - Weight Adders Frame Flange Mount 00B Bushed 00S SCD 31 N/A N/A N/A RO Series D-89

90 Helical Shaft Mount Speed Reducers Input Shaft C-Face Series Scoop Mount Top Mount D-90

91 Table of Contents Speed Reducers Section Page Design Features...D-92 Mounting Versatility and Size Range...D-93 Speed Reducer Sslection...D-94 - D-95 Catalog Nomenclature...D-96 - D-97 Reducer Mounting Configuration...D-98 Reducer Mounting Positions...D-98 AC Motors...D-99 Tapered Bushing Selections...D D-101 Screw Conveyor Accessories...D D-103 Mounting Accessories (Silent-Bloc and Tie Rod)...D-104 Modifications, Options and Accessories...D-105 AGMA Application Classifications...D D-108 Speed Reducer Selection Tables...D D-119 Dimension Prints C-Face 00C Finished Bore Shaft Mount Reducers...D-120 D-124 C-Face 40C Finished Bore Face Mount Reducers...D-120 D-124 C-Face 50C/60C Finished Bore Flange Mount Reducers...D-125 D-128 C-Face 00B Tapered Bushed Shaft Mount Reducers...D-129 D-132 C-Face 00S Screw Conveyor Drive Reducers...D-133 D-134 Input Shaft 00C Finished Bore Shaft Mount Reducers...D-135 D-138 Input Shaft 40C Finished Bore Face Mount Reducers...D-135 D-138 Input Shaft 50C/60C Finished Bore Flange Mount Reducers...D-139 D-142 Input Shaft 00B Tapered Bushed Shaft Mount Reducers...D-143 D-146 Input Shaft 00S Screw Conveyor Drive Reducers...D-147 D-148 Scoop Mount 00C Finished Bore Shaft Mount Reducers...D-150 D-151 Scoop Mount 40C Finished Bore Face Mount Reducers...D-149 D-151 Scoop Mount 50C/60C Finished Bore Flange Mount Reducers...D-152 D-154 Scoop Mount 00B Tapered Bushed Shaft Mount Reducers...D-155 D-157 Scoop Mount 00S Screw Conveyor Drive Reducers...D-158 Top Mount 40C Finished Bore Face Mount Reducers...D-159 Top Mount 50C/60C Finished Bore Flange Mount Reducers...D-160 Top Mount 00B Tapered Bushed Shaft Mount Reducers...D-161 Top Mount 00S Screw Conveyor Drive Reducers...D-162 Speed Reducer Weights...D-163 Lubrication...D-164 Hollow Shaft Details...D-165 NEMA Standard Dimensions...E-10 General Information...E-11 Standard Terms and Conditions of Sale...E-12 Series D-91

92 Helical Shaft Mount Speed Reducers Series 8. Magnetic Drain Plug Standard D-92 Design Features 1. Gearcase Supplied Factory Filled with Synthetic Oil Wide temperature range and longer life. 2. Tapered Bushed Version Available on Gear Frame Sizes 2-6 Each frame available with a variety of bushing bore diameters. Frames 2-5 utilize a unique patented reversible single bushing system with a stabilizing ring to minimize wobble for reduced wear and tear. It includes an end cap to seal the quill end from contamination. 3. Series C-Face Reducers with Compact Quill Design Non-metallic liner to eliminate fretting. Shorter design Two bearings for support. 4. Gears and Shafts of Nickel Chromium Molybdenum Steel Helical gearing is case hardened and then skived, superfinished, or ground. All gears heat shrunk on shafts or mounted on self-locking tapered shafts and keyed for high shock load capability. 5. Corrosion and Shock Resistant Cast Iron Housing One piece, reinforced and ribbed for extra strength. 6. Normally Closed Breather with Multiple Locations (Optional ) 7. Double Lip Seals on Heat Treated, Plunge Ground Shafts

93 Speed Reducers Mounting Versatility and Size Range Standard Hollow Shaft Silent-Bloc/Tie Rod Frames 1 6 Max. 44,000 lb-in Face Mount Shaft Mount Frames 1-6 Max. 44,000 lb-in NEMA C-Face 56C to 326TC C-Face Motors Frames 56C - 326TC Flange Mount Hollow Shaft Frames 2-6 Max. 44,000 lb-in Backstop Option Frames Tapered Bushed Silent-Bloc/Tie Rod Frames 2-6 Max. 44,000 lb-in Scoop Mount Frames to 326T Screw Conveyor Drive Frames 2-5 Max. 26,800 lb-in Input Shaft Frames 1-6 Top Mount Frames to 286T Series High Ratio Combined Frames 2-6 All Styles Max. 44,000 lb-in 1 Backstop not available for frame 1 C-Face, or for frames 2-3 combined (i.e. more than 3 gear stages). 2 Scoop mount is not available for combined (i.e. more than 3 gear stages) frames Top mount is not available for combined units (i.e. more than 3 gear stages). D-93

94 Speed Reducers Selection Selection Information 1. Input HP Based on application data. 2. Speed/Ratio Obtain either desired output speed (rpm) or gearbox ratio based on application. 3. Service Factor Determine the required service factor using either the AGMA application classification chart (pages D D-108), or the duration of operation, load type, and drive type with the table below: Prime Mover Electric Motor Internal Combustion Engine Hours of Operation Uniform Load U Moderate Shock Load M Heavy Shock Load V Size Selection Step 1 Locate speed reducer selection tables (pages D D-119) based on input speed to gearbox. Step 2 Choose the nominal ratio appropriate for the speeds required. Size Selection (cont.) Step 3 Select the gear unit size for the chosen ratio and the known input speed so that the mechanical power rating P (hp) satisfies the following: P P P m SF = mechanical power rating (hp) of gearbox P m = motor power (hp) SF = required service factor Note: Size selection based on absorbed power (Pa) or absorbed torque (Ta) at the low speed shaft instead of motor power (Pm) is allowed when the former is known with sufficient accuracy and if the number of start operations is limited. When Ta is applied in size selection, verify if: T T a SF T = torque rating (in. lbs.) at low speed shaft Ta = absorbed torque (in. lbs.) at low speed shaft SF = required service factor Step 4 Verify that unit selected is not thermally limited (indicated by shading in ratings table). Series D-94

95 Speed Reducers Selection Example 1. Application Data Belt conveyor with uniform load, 12- hrs/day operation. Customer prefers tapered bushed shaft mount style reducer with a tie rod. The unit will be mounted to a 1.75" diameter horizontal shaft with the motor above. A c-face mounted motor will be used. Motor rating: 5 HP, 1750 RPM, 184TC Footless Frame, 230/460 VAC, 3-Phase, 60 Hz, TEFC Output speed: 44 rpm 2. Size Selection Nominal Ratio: Service Factor: Rating Req d: Catalog Rating: Locate Nominal RPM closest to 44 RPM. 40:1 Nominal Ratio is the proper selection. Using AGMA application classification chart (Page D-106) under the Conveyors - General Purpose heading, Uniformly Loaded or Fed conveyors that operate over 10 hours/day should have a 1.25 service factor. Minimum reducer rating required is P = P m x SF = 5 HP x 1.25 = 6.25 HP Using 1750 rpm selection table (page D-110.) 3. Catalog Designation Reducer: B-P3-40-U-184TC (See page D-96.) Bushing: 207TBP112 (See page D-101.) Tie Rod: MUB999TA002 (See Page D-104.) 4. Motor Model Number Selection Part Number: U5S2ACR (See Page D-99.) Specifications: 5 HP, 1750 rpm, 184TC Footless Frame,230/460 VAC, 3-Phase, 60 Hz, TEFC Exact ratio Gear Frame Input H.P. Output Torque Selection: 3472 is rated HP input / 13,939 lb-in output with 37.4:1 ratio 1750 RPM / 37.4 = 46.8 rpm output speed / 5 = 2.16 Service Factor Series D-95

96 Ordering C P U 145TC M11 See page D-98. Browning Helical Shaft Mount Series Reducer Size Series Series Stages = 2 stages = 3 stages or 4A = 4 stages combined 5 or 5A = 5 stages combined 6 or 6A = 6 stages combined Output Face/Flange & Shaft Configuration 00C = Straight Hollow Bore with No Face or Flange 1 Mounting Position P3 Nominal Gear Ratio 22.4 = 22.4:1 InputType U=C-Face 40C = Straight Hollow Bore wth UD=C-Face with P6 B14 Face Mount Backstop Use 50C = Straight Hollow Bore with P7 Nominal AP=Input Shaft B5 Flange Mount 2 Ratio Selected AD=Input Shaft P8 from with Backstop Reducer 60C = Straight Hollow Bore with SP=Scoop PV5 Selection Alternate B5 Flange Mount 2 Mount Tables 00B = Tapered Bushed Output with No Face or Flange Mount 2 00S = CEMA Screw Conveyor Drive Output 2 PV6 SD=Scoop Mount With Backstop TM=Top Mount TD=Top Mount with Backstop Motor Frame (All except input shaft type) C- Fa ce 56C-326TC Scoop Mount T Top Mount T Modifications Select from Available Modifications Listed on Page D The 00C is only available on Series Not available on frame 31. Series Flange Dimensions (mm) BD AK AJ Gear Frame Output Flange Part Number Designator 31 Flange Not Available 32 60C 50C 33 60C 50C 34 60C 50C 35 50C 26 50C D-96

97 Ordering / C-Face Reducers Motor Frame 56C 143TC 182TC 213TC 254TC 284TC 324TC 145TC 184TC 215TC 256TC 286TC 326TC Gear Frame Range of Ratios Available :1, 9:1-71:1 7.1:1, 9:1-71:1 3242/3202 4:1-35.5:1 4:1-35.5:1 4:1-31.5:1 4:1-20:1 3243/ :1-224:1 40:1-224:1 40:1-140: :1-1,400:1 250:1-900: ,600:1-6,300:1 1,600:1-4,000: :1-56:1 5.6:1-56:1 5.6:1-56:1 5.6:1-35.5: :1-315:1 63:1-315:1 63:1-280:1 63:1-180: :1-2,000:1 355:1-1,250: ,240:1-10,000:1 2,240:1-3,550: :1-50:1 8:1-50:1 8:1-50:1 8:1-50:1 5:1-40:1 5:1-18: :1-250:1 56:1-250:1 56:1-250:1 56:1-160:1 56:1-160: :1-1,600:1 250:1-1,600:1 250:1-1,000: ,800:1-7,100:1 1,800:1-7,100:1 1,800:1-4,500: ,000:1-10,000:1 8,000:1-10,000:1 8,000:1-10,000: :1-31.5:1 9:1-31.5:1 9:1-31.5:1 9:1-31.5:1 5:1-31.5:1 5:1-20:1 5:1-20: :1-224:1 63:1-224:1 63:1-224:1 63:1-224:1 35.5:1-224:1 35.5:1-140:1 35.5:1-140: :1-500:1 250:1-500:1 250:1-500: :1-2,800:1 560:1-2,800:1 560:1-1,600: ,150:1-10,000:1 3,150:1-10,000:1 3,150:1-8,000: :1-35.5:1 12.5:1-35.5:1 7.1:1-35.5:1 7.1:1-35.5: :1-200:1 20:1-200:1 20:1-140:1 20:1-140:1 20:1-80:1 2604A 224:1-1,000:1 224:1-1,000:1 224:1-1,000:1 224:1-630:1 224:1-630:1 2605A 900:1-4,000:1 900:1-4,000:1 900:1-4,000:1 900:1-2,500:1 900:1-2,500:1 2606A 3,550:1-10,000:1 3,550:1-10,000:1 3,550:1-10,000:1 3,550:1-10,000:1 3,550:1-10,000:1 / Scoop Mount Reducers Motor Frame T 145T 182T 184T 213T 215T 254T 256T 284T 286T 324T 326T Gear Frame Frames Available 3132 Not Available 3242/3202 X X /3203 X X Not Available 3245 Not Available 3362 X X X X X X Not Available 3365 Not Available X X X X X X Not Available 3475 Not Available 3476 Not Available X X X X X X X X X X Not Available 3585 Not Available 3586 Not Available X X X X X X X X X X 2604A X X X A X X X A X X X / Top Mount Reducers Motor Frame T 145T 182T 184T 213T 215T 254T 256T 284T 286T Gear Frame Frames Available 3132 Not Available 3242/3202 X X X /3203 X X X Not Available 3245 Not Available 3362 X X X X X X X X Not Available 3365 Not Available X X X X X X X X Not Available 3475 Not Available 3476 Not Available X X X X X X X X X X 3584 Not Available 3585 Not Available 3586 Not Available 2602 Not Available 2603 Not Available 2604A Not Available 2605A Not Available 2606A Not Available D-97 Series

98 Speed Reducers Mounting Positions Mounting Configuration Face Mount Hollow Shaft Flange Mount Hollow Shaft Tapered Bushed Screw Conveyor Drive 40C 50C/60C 00B 00S l Normally Stocked - Not Available Availability Gear Frame 40C 50C 60C 00B 00S 31 l l l l l l 33 l l l l l 34 l l l l l 35 l l - l l 26 l l - l - Mounting Positions Series P3 P6 P7 P8 PV5 PV6 D-98

99 HP FRAME AC Motors Selection C-Face Footless CTEF CTFB CTIF CTIFB ENERGY EFFICIENT ENERGY EFFICIENT INVERTER DUTY INVERTER DUTY TEFC TEFC WITH BRAKE TEFC TEFC WITH BRAKE /460 VAC 3-PH/60 HZ 575 VAC 3-PH/60 HZ 230/460 VAC 3-PH/60 HZ 575 VAC 3-PH/60 HZ 230/460 VAC 3-PH/60 HZ 575 VAC 3-PH/60 HZ 230/460 VAC 3-PH/60 HZ 575 VAC 3-PH/60 HZ 1/3 56C RC0102 RC0602 RC0100 RC0600 RC0103 RC0603 RC0151 RC0651 1/2 56C RD0102 RD0602 RD0100 RD0600 RD0103 RD0603 RD0151 RD0651 3/4 56C RE0102 RE0602 RE0100 RE0600 RE0103 RE0603 RE0151 RE TC RF0102 RF0602 RF0100 RF0600 RF0103 RF0603 RF0151 RF C RF0152 RF0652 RF0150 RF0650 RF0153 RF0653 RF0159 RF /2 145TC RG0102 RG0602 RG0100 RG0600 RG0103 RG0603 RG0151 RG C RG0152 RG0652 RG0153 RG TC RH0102 RH0602 RH0100 RH0600 RH0103 RH0603 RH0151 RH0651 Usable as follows: 230/460 VAC, 60 Hz with 1.35 SF 208 VAC, 60 Hz with 1.0 SF 380 VAC, 50 Hz with 1.0 SF Usable as follows: 230/460 VAC, 60 Hz with 1.25 SF 208 VAC, 60 Hz with 1.0 SF 380 VAC, 50 Hz with 1.0 SF Usable as follows: 230/460 VAC, 60 Hz with 1.35 SF 380 VAC, 50 Hz with 1.0 SF Usable as follows: 230/460 VAC, 60 Hz with 1.25 SF 380 VAC, 50 Hz with 1.0 SF CTEF / CTIF Conversion Kits Type Kit Consists of Fits Kit Part ID Cast Iron Conduit Box Base, Cover, Gaskets, Hardware, 2 Threaded Openings 56C and 140TC Frame RA9000 Cast Iron Fan Cover Guard Fully Compliant with NEMA MG1 Part 31 Cast Iron Fan Cover 56C and 140TC Frame RA9100 HP FRAME C-Face Footless UNIMOUNT UNIMOUNT 841 Plus eline STD EFFICIENCY TEFC ENERGY EFFICIENT TEFC Rigid Base Mount PREMIUM EFFICIENT IEEE 841 Duty ENERGY EFFICIENT Severe Duty /460 VAC 575 VAC /460 VAC 575 VAC 460 VAC /460 VAC 575 VAC 3-PH/60 HZ 3-PH/60 HZ 3-PH/60 HZ 3-PH/60 HZ 3-PH/60 HZ 3-PH/60 HZ 3-PH/60 HZ 1/4 56C U14S2ACR 1/3 56C U13S2ACR 1/2 56C U12S2ACR U12S2GCR 3/4 56C U34S2ACR U34S2GCR 1 143TC U1S2ACR U1S2GCR 8P1P2CCR ELT1E2DC ELT1E2GC 56C U1S2AFCR 1-1/2 145TC U32S2ACR U32S2GCR 8P32P2CCR ELT32E2DC ELT32E2GC 56C U32S2AFCR U32S2GFCR 2 145TC U2S2ACR U2S2GCR 8P2P2CCR ELT2E2DC ELT2E2GC 56C U2S2AFCR 3 182TC U3S2ACR U3S2GCR U3E2DCR U3E2GCR 8P3P2CCR ELT3E2DC ELT3E2GC 5 184TC U5S2ACR U5S2GCR U5E2DCR U5E2GCR 8P5P2CCR ELT5E2DC ELT5E2GC 7-1/2 213TC U7S2ACR U7S2GCR U7E2DCR U7E2GCR 8P7P2CCR ELT7E2DC ELT7E2GC TC U10S2ACR U10S2GCR U10E2DCR U10E2GCR 8P10P2CCR ELT10E2DC ELT10E2GC TC U15S2ACR U15E2DCR U15E2GCR ELT15E2DC ELT15E2GC TC U20S2ACR U20E2DCR U20E2GCR ELT20E2DC ELT20E2GC TC U25S2ACR U25E2DCR U25E2GCR ELT25E2DC ELT25E2GC TC U30S2ACR U30E2DCR U30E2GCR ELT30E2DC ELT30E2GC s C-Face footed motor. UNIMOUNT HOSTILE DUTY eline ENERGY EFFICIENT ENERGY EFFICIENT ENERGY EFFICIENT HP FRAME TEFC TEFC Severe Duty /460 VAC 575 VAC 200 VAC 230/460 VAC 575 VAC 200 VAC /460 VAC 575 VAC 3-PH/60 HZ 3-PH/60 HZ 3-PH/60 HZ 3-PH/60 HZ 3-PH/60 HZ 3-PH/60 HZ 3-PH/60 HZ 3-PH/60 HZ 1 143T U1E2D U1E2G U1E2H H1E2D H1E2G H1E2H ELT1E2D ELT1E2G 1-1/2 145T U32E2D U32E2G U32E2H H32E2D H32E2G H32E2H ELT32E2D ELT32E2G 2 145T U2E2D U2E2G U2E2H H2E2D H2E2G H2E2H ELT2E2D ELT2E2G 3 182T U3E2D U3E2G U3E2H H3E2D H3E2G H3E2H ELT3E2D ELT3E2G 5 184T U5E2D U5E2G U5E2H H5E2D H5E2G H5E2H ELT5E2D ELT5E2G 7-1/2 213T U7E2D U7E2G U7E2H H7E2D H7E2G H7E2H ELT7E2D ELT7E2G T U10E2D U10E2G U10E2H H10E2D H10E2G H10E2H ELT10E2D ELT10E2G T U15E2D U15E2G U15E2H H15E2D H15E2G H15E2H ELT15E2D ELT15E2G T U20E2D U20E2G U20E2H H20E2D H20E2G H20E2H ELT20E2D ELT20E2G T U25E2D U25E2G U25E2H H25E2D H25E2G H25E2H ELT25E2D ELT25E2G T U30E2D U30E2G U30E2H H30E2E H30E2G H30E2H ELT30E2D ELT30E2G T H40E2E H40E2G H40E2H ELT40E2D T H50E2E H50E2G H50E2H ELT50E2D Series Unimount, 841 Plus and eline are registered trademarks of Emerson Electric Co. Emerson Power Transmission Corporation cannot and does not represent or warrant the accuracy of this information. D-99

100 32-35 and 26 units can be ordered with a 00B bushed output version. When a bore size is defined at order entry, this configuration includes the appropriate bushing kit unassembled. The table below shows the available stocked bushing bores that may be specified for each frame size. Each bushing kit is supplied with the bushing, mounting hardware, and a stabilizer ring (except 26 which has no stabilizer ring). Where a bushing is needed for a spare or for a bore size change, select it from the following table by gear frame size unique, patented single bushing mounting system - Mounts from either side - Tapered stabilizer ring minimizes wobble - End cap seals quill end from contamination - Resists fretting corrosion Tapered Bushings Stabilizer Ring Series Frame Meas. Unit Inch Bushing No. Bore Shaft Keyseat Required Type Stabilizer Ring Width Size Bolt Torque (Ft-Lbs) Weight (Lbs) 107TBP012 3/4 3/16 x 3/32 x 3 7/ TBP014 7/8 3/16 x 3/32 x 3 7/ TBP015 15/16 1/4 x 1/8 x 3 7/ TBP /4 x 1/8 x 3 7/ TBP /16 1/4 x 1/8 x 3 7/ TBP /8 1/4 x 1/8 x 3 7/ TBP /16 1/4 x 1/8 x 3 7/ /16-18 x 1 1/ TBP /4 1/4 x 1/8 x 3 7/ TBP /16 5/16 x 5/32 x 3 7/ TBP /8 5/16 x 5/32 x 3 7/ TBP /16 3/8 x 3/16 x 3 7/ TBP30MM 30 mm 8 x 4 x 94 (mm) Metric 1 107TBP35MM 35 mm 10 x 5 x 94 (mm) TBP015 15/16 1/4 x 1/8 x 4 1/ TBP /4 x 1/8 x 4 1/ TBP /16 1/4 x 1/8 x 4 1/ TBP /8 1/4 x 1/8 x 4 1/ TBP /16 1/4 x 1/8 x 4 1/ Inch 115TBP /4 1/4 x 1/8 x 4 1/ TBP /16 5/16 x 5/32 x 4 1/ TBP /8 5/16 x 5/32 x 4 1/ TBP /16 3/8 x 3/16 x 4 1/ /8-16 x 1 1/ TBP /2 3/8 x 3/16 x 4 1/ TBP /8 3/8 x 3/16 x 4 1/ TBP /16 3/8 x 3/16 x 4 1/ TBP /4 3/8 x 3/16 x 4 1/ TBP /8 1/2 x 1/4 x 4 1/ TBP /16 1/2 x 1/4 x 4 1/ TBP40MM 40 mm 12 x 5 x 100 (mm) Metric 1 115TBP45MM 45 mm 14 x 5.5 x 100 (mm) Metric bushings have metric bores and require metric keyseats as shown in mm. D-100

101 Tapered Bushings Driven Shaft Key (Furnished) Type 3 Frame 34 Meas. Unit Inch Bushing No. Bore Shaft Keyseat Required Type Stabilizer Ring Width Size Bolt Torque (Ft-Lbs) Weight (Lbs) 207TBP /8 5/16 X 5/32 x 5 1/ TBP /16 3/8 X 3/16 X 5 1/ TBP /2 3/8 X 3/16 X 5 1/ TBP /8 3/8 X 3/16 X 5 1/ TBP /16 3/8 X 3/16 X 5 1/ TBP /4 3/8 X 3/16 X 5 1/ TBP /8 1/2 X 1/4 X 5 1/ TBP /16 1/2 X 1/4 X 5 1/ /8-16 X 1 1/ TBP /2 X 1/4 X 5 1/ TBP /8 1/2 X 1/4 X 5 1/ TBP /16 1/2 X 1/4 X 5 1/ TBP /4 1/2 X 1/4 X 5 1/ TBP /16 5/8 X 5/16 X 5 1/ TBP50MM 50 mm 14 x 5.5 x 125 (mm) Metric 1 207TBP60MM 60 mm 18 x 7 x 125 (mm) TBP /16 3/8 X 3/16 X 5 5/ TBP /2 3/8 X 3/16 X 5 5/ TBP /16 3/8 X 3/16 X 5 5/ TBP /4 3/8 X 3/16 X 5 5/ Inch 26 Inch 215TBP /8 1/2 X 1/4 X 5 5/ TBP /16 1/2 X 1/4 X 5 5/ TBP /2 X 1/4 X 5 5/ TBP /16 1/2 X 1/4 X 5 5/8 2 3/8-16 X 1 3/ TBP /4 1/2 X 1/4 X 5 5/ TBP /16 5/8 X 5/16 X 5 5/ TBP /2 5/8 X 5/16 X 5 5/ TBP /16 5/8 X 5/16 X 5 5/ TBP /16 3/4 x 3/8 x 5 5/ Metric 1 215TBP60MM 60 mm 18 x 7 x 172 (mm) 2 NA /16 5/8 X 5/16 X /2 5/8 X 5/16 X /16 3/4 x 3/8 x /8 3/4 x 3/8 x NA /16 3/4 x 3/8 x /16 3/4 x 3/8 x /16 7/8 x 7/16 x Metric bushings have metric bores and require metric keyseats as shown in mm. Series D-101

102 Screw Conveyor Drive Shafts 2 2 Complete the shaft part number by adding shaft type as follows: Screw Conveyor Drives Standard 2 hole steel shaft = leave blank (example 107DSP108) Optional 3 hole steel shaft = add -3 (example 107DSP108-3) 2 hole stainless steel shaft = add SS (example 107DSP108SS) 3 hole stainless steel shaft = add -3SS (example 107DSP108-3SS) Gear Frame 1 1/2 Dia. Shaft for 6 & 9 Dia. Screw 2 Dia. Shaft for 9 & 12 Dia. Screw 2 7/16 Dia. Shaft for 12 & 14 Dia. Screw 3 Dia. Shaft for Dia. Screw 3 7/16 Dia. Shaft for Dia. Screw 31 Not Available DSP DSP DSP DSP300 N/A DSP DSP DSP DSP300 N/A 34 N/A 207DSP DSP DSP DSP N/A 215DSP DSP DSP DSP Not Available Screw Conveyor Accessories Gear Frame Optional Seal Cartridges Felt Seal 1 Waste Pack Kit Packing Gland Kit 31 Not Available WPP 107PGP FR WPP PGP FR WPP PGP FR WPP PGP FR Not Available 1 Felt seal can only be added to the waste pack seal cartridge kit. Screw Conveyor Drives May Be Assembled in the Field Required Components Include: 00S reducer with screw conveyor adapter Screw conveyor drive shaft Series Optional Components Include: Waste pack Packing gland Felt seal Waste Pack Kit Felt Seal Screw Conveyor Adapter (Included with type 00S gear unit) Packing Gland Kit Screw Conveyor Drive Shaft Kit Screw Conveyor Thrust Ratings Output tapered roller bearing standard - all sizes. D-102 Gear Frame Maximum Thrust Rating (Lbs.)

103 Screw Conveyor Trough Ends Table No. 33 Formed Hot Roll Plate Steel Specifications Part No. Conveyor Drive Shaft Dimensions Fig. Type Screw Dia. Dia. A B C D E F G H J K L SCTE06 x 1 1/2" 6" 1 1/2" 1 6-Hole 10 1/8" 4 1/2" 1 1/2" 1 3/4" 1" 9 3/4" 4 7/8" 1 3/4" 9/16" 2" 8 1/8" SCTE09 x 1 1/2" 9 1 1/2 2 8-Hole /8 1 5/8 2 5/8 1 1/2 13 3/4 6 7/8 1 3/4 9/ /8 SCTE09 x Hole /8 1 5/8 2 5/8 1 1/2 13 3/4 6 7/8 2 1/4 11/16 2 9/16 9 3/8 SCTE10 x 1 1/ /2 2 8-Hole 15 1/4 6 3/8 2 3/8 2 7/8 1 3/4 14 3/4 7 3/8 1 3/4 9/ /2 SCTE10 x Hole 15 1/4 6 3/8 2 7/8 2 7/8 1 3/4 14 3/4 7 3/8 2 1/4 11/16 2 9/16 9 1/2 SCTE12 x Hole 17 3/8 7 3/ /4 1 5/8 17 1/4 8 5/8 2 1/4 11/16 2 9/ /4 SCTE12 x 2 7/ / Hole 17 3/8 7 3/ /4 1 5/8 17 1/4 8 5/8 2 11/16 11/ / /4 SCTE12 x Hole 17 3/8 7 3/ /4 1 5/8 17 1/4 8 5/8 3 1/4 13/ /4 SCTE14 x 2 7/ / Hole 20 1/8 9 1/ /8 1 5/8 19 1/4 9 5/8 2 11/16 11/16 2 3/ /2 SCTE14 x Hole 20 1/8 9 1/ /8 1 5/8 19 1/4 9 5/8 3 1/4 13/ /2 SCTE16 x Hole 22 5/8 10 5/8 2 1/2 3 1/ /4 10 5/8 3 1/4 13/ /8 SCTE18 x Hole 25 1/2 12 1/8 2 1/2 3 1/ /4 12 1/8 3 1/4 13/ SCTE18 x 3 7/ / Hole 25 1/2 12 1/8 2 1/2 3 1/ /4 12 1/8 3 11/16 13/16 3 3/8 16 SCTE20 x Hole 28 1/2 13 1/2 2 1/2 3 3/4 2 1/4 26 1/4 13 1/8 3 1/4 13/ /4 SCTE20 x 3 7/ / Hole 28 1/2 13 1/2 2 1/2 3 3/4 2 1/4 26 1/4 13 1/8 3 11/16 13/16 3 3/8 19 1/4 SCTE24 x 3 7/ / Hole 34 5/8 16 1/2 2 1/2 4 1/8 2 1/2 30 1/4 15 1/8 3 11/16 13/16 3 3/8 20 Part No. Dimensions M N P Q R S T U V W X Y Z AB Wt. Lbs. SCTE06 x 1 1/2" 4 1/16 4 7/ /32 5/8 3 15/16 2 1/32 3/16 7/ / / SCTE09 x 1 1/2" 4 11/16 6 1/4 4 15/16 13/ / /64 1/4 7/ /64 2 9/ / SCTE09 x /16 6 1/4 4 15/16 13/ / /64 1/4 7/ /64 2 9/ / SCTE10 x 1 1/2 4 3/4 6 5/8 4 1/8 5/8 3 3/8 6 1/8 1/4 7/ / / / SCTE10 x 2 4 3/4 6 5/8 4 1/8 5/8 3 3/8 6 1/8 1/4 7/ / / / SCTE12 x 2 6 1/8 7 15/16 6 1/4 15/16 4 7/ /64 5/16 9/ /64 3 7/ / SCTE12 x 2 7/16 6 1/8 7 15/16 6 1/4 15/16 4 7/ /64 5/16 9/ /64 3 7/ / SCTE12 x 3 6 1/8 7 15/16 6 1/4 15/16 4 7/ /64 5/16 9/ /64 3 7/ / SCTE14 x 2 7/16 6 3/4 8 15/ /32 1 3/ / /64 5/16 9/ / / SCTE14 x 3 6 3/4 8 15/ /32 1 3/ / /64 5/16 9/ / / SCTE16 x 3 7 7/ /8 4 57/ /64 5/16 11/ /32 3 3/ / SCTE18 x /2 3 9/ / /64 5/16 11/ / / / /16 11/ SCTE18 x 3 7/ /2 3 9/ / /64 5/16 11/ / / / /16 11/ SCTE20 x 3 9 5/8 12 3/ / / /64 8 3/16 3/8 11/ / /64 9 1/ /32 13/ SCTE20 x 3 7/16 9 5/8 12 3/ / / /64 8 3/16 3/8 11/ / /64 9 1/ /32 13/ SCTE24 x 3 7/ / / /32 31/ /64 3/8 11/ / / /8 9 7/32 s 13/16 3 5/ Notes: Browning Trough Ends are drilled to fit CEMA standard troughs. The center holes are drilled to fit Browning Screw Conveyor Drives. s Figure 4 has 2 Z holes in bottom flange only; no holes in top flange. D-103 Series

104 Speed Reducers Mounting Accessories Standard Mounting By Reaction Point The use of "Silent-Bloc" is recommended for standard mounting of OOC and OOB style units, or 40C units not utilizing face for mounting. These resilient rubber bushings help to minimize vibration. Order by part number below. Silent-Bloc Option Size Silent-Bloc Kit # ID x OD x Thickness MUB230AM x 1.57 x MUB450AM x 2.36 x MUB600AM x 3.15 x 1.20 Optional Mounting with Tie Rod A conventional tie rod kit is available as shown in the diagram below. It is used to secure the 00C or 00B style housing to a solid machine surface and prevent rotation of the gear unit. Tie Rod can be used with 40C units not utilizing face for mounting. Order by the part number in the table below: G F E B C D A Series Note: Tie rod may be mounted on the opposite side if desired. Dimensions (Inches) Gear Frame Tie Rod Kit # A B C D E F MIN. MAX. G MUB999TA MUB999TA MUB999TA Note: Tie rod assemblies should always be mounted in tension. D-104

105 Speed Reducers Modifications, Options and Accessories M11 Corro-Duty Corro-Duty speed reducers are designed for applications in food processing, chemical, poultry and any other industries that will be subjected to extreme humidity, washdown, steam, detergents and mild acids. The Corro-Duty option includes a normally closed breather in the gear case. The exterior of the entire unit is then painted in one of the two options chosen at order entry. Option #1 - Corro-Duty grey 3 step paint system using 316 stainless steel paint Light grey semigloss finish USDA and FDA approved Option #2 - Corro-Duty white 2 step paint system using epoxy paint White gloss finish USDA and FDA approved M12 Normally Closed Breather This breather helps protect against lubricant contamination in applications with flying dust, lint or washdown. A normally closed breather is standard on all frame sizes of series and. M18 Oil Level View Port This clear port is installed in place of the oil level plug. It allows maintenance personnel a convenient means of checking for proper oil level without removing plugs. Proper View Port part numbers are: Gear Frame Size Part Number /4 BSPP Male /4 BSPP Male Face and Flanged Output (Designated under Brackets and Shafts) Speed reducers with faced or flanged outputs are available from stock. Refer to page D-98 and individual dimension pages for options available based on gear frame size. Synthetic Oil speed reducers are supplied factory-filled with a premium synthetic oil. Refer to pages D D165 for complete details of lubricants. M13 NPT Adapter These adapters convert metric threads of breather, drain and/or oil level holes in the reducer to standard NPT threads. They are required for customer additions of site glasses, sight tubes, special breathers and other plumbing accessories. The adapter(s) is supplied loose for mounting by others. Gear Frame Size Part Number /4 NPFT /4 NPFT M15 Export Boxing Export boxing can be provided for "underdeck" transport. When the quantity of speed reducers exceeds five units, refer to the sales department for the most economical accommodations. M16 Special Nameplate Units can be provided with limited, additional, special information on the standard product nameplate. When requested, a special nameplate may be provided and stamped with custom markings. Series M17 Coupling Guard For scoop mount series, this kit includes cover, base and hardware. D-105

106 Brewing and Distilling Bottling Machinery Brew Kettles, Continuous Duty Cookers - Continuous Duty Mash Tubs - Continuous Duty Scale Hoppers, Frequent Starts Speed Reducers AGMA Application Classifications Application Service Factor Application Service Factor Up to Up to Over Up to Up to Over hrs/day hrs/day hrs/day hrs/day hrs/day hrs/day Agitators (Mixers) Pure Liquids Cranes (Continued) Boom Hoist Refer to Application Engineering Liquids & Solids Trolley Drive Refer to Application Engineering Liquids - Variable Density (Gantry Drive) (Traction Drive) Refer to Application Engineering Blowers Centrifugal Mill Duty Main Refer to Application Engineering Lobe Auxiliary Refer to Application Engineering Vane Bridge & Trolley Travel Refer to Application Engineering Industrial Duty Main Auxiliary Refer to Application Engineering Bridge & Trolley Travel Refer to Application Engineering Crusher Stone or Ore Series Can Filling Machines Car Dumpers Car Pullers Clarifiers Classifiers Clay Working Industry Brick Press Briquette Machine Pug Mill Compactors Compressors Centrifugal Lobe Reciprocating, Multi - Cylinder Reciprocating, Single - Cylinder Conveyors - General Purpose Uniformly Loaded or Fed Not Uniformly Fed Reciprocating or Shaker Cranes Dry Dock Main Hoist Auxiliary Boom Hoist Slewing Drive Traction Drive Container Main Hoist Refer to Application Engineering Dredges Cable Reels Conveyors Cutter Head Drives Pumps Screen Drives Stackers Winches Elevators Bucket Centrifugal Discharge Escalators Refer to Application Engineering Freight Refer to Application Engineering Gravity Discharge Extruders General Plastics (a) Variable Speed Drive (b) Fixed Speed Drive Rubber (a) Continuous Screw Operation (b) Intermittent Screw Operation Fans Centrifugal Cooling Towers Refer to Application Engineering Forced Draft Induced Draft Industrial & Mine D-106

107 Feeders Apron Belt Disc Reciprocating Screw Food Industry Cereal Cooker Dough Mixers Meat Grinders Slicers Generators and Exciters Hammer Mills Hoists Heavy Duty Medium Duty Skip Hoist Laundry Tumblers Laundry Washers Lumber Industry Barkers - Spindle Feed Main Drive Conveyors - Burner Main or Heavy Duty Main Log Re-Saw, Merry-Go-Round Slab Transfer Chains - Floor Green Cut-Off Saws - Chain Drag Debarking Drums Feeds - Edger Gang Trimmer Log Deck Log Hauls - Incline-Well Type Log Turning Devices Planner Feed Planer Tilting Hoists Rolls - Live-Off Bearing.-Roll Cases Sorting Table Tipple Hoist Transfers - Chain Causeway Tray Drives Veneer Lathe Drives Refer to Application Engineering Speed Reducers AGMA Application Classifications Application Service Factor Application Service Factor Up to Up to Over hrs/day hrs/day hrs/day Up to Up to Over hrs/day hrs/day hrs/day Metal Mills Draw Bench Carriage & Main Drive Runout Table Non-reversing Group Drives Individual Drives Reversing Slab Pushers Shears Wire Drawing Wire Winding Machine Metal Strip Processing Machinery Bridles Coilers & Uncoilers Edge Trimmers Flatteners Loopers (Accumulators) Pinch Rolls Scrap Choppers Shears Slitters Mills, Rotary Type Ball & Rod Spur Ring Gear Helical Ring Gear Direct Connected Cement Kilns Dryers & Coolers Mixers, Concrete Paper Mills Agitator (Mixer) Agitator for Pure Liquids Barkers - Mechanical Barking Drums Beater Breaker Stack v Calender Chipper Chip Feeder Coating Rolls Conveyors Chip, Bark, Chemical Log (Including Slab) Couch Rolls Cutter Cylinder Molds v Dryers Paper Machine Conveyor Type Embosser Extruder Fourdrinier Rolls (Includes Lump Breaker, Dandy Roll, Wire Turning, and Return Rolls) Jordan Kiln Drive Mt. Hope Roll Series D-107

108 Series Speed Reducers AGMA Application Classifications Application Service Factor Application Service Factor Up to Up to Over hrs/day hrs/day hrs/day Paper Mills (Continued) Paper Rolls Platter Presses - Felt & Suction Pulper Pumps - Vacuum Reel (Surface Type) Screens Chip Rotary Vibrating Size Press Super Calender (See Note) Thickner (AC Motor) (DC Motor) Washer (AC Motor) (DC Motor) Wind and Unwind Stand Winders (Surface Type) v Yankee Dryers Plastics Industry - Primary Processing Intensive Internal Mixers (a) Batch Mixers (b) Continuous Mixers Batch Drop Mill - 2 Smooth Rolls Continuous Feed, Holding & Blend Mill Compounding Mills Calenders Plastics Industry - Secondary Processing Blow Molders Coating Film Pipe Pre-Plasticizers Rods Sheet Tubing Pullers - Barge Haul Pumps Centrifugal Proportioning Reciprocating Single Acting, 3 or more cylinders Double Acting, 2 or more cylinders Rotary - Gear Lobe Vane Up to Up to Over hrs/day hrs/day hrs/day Rubber Industry Intensive Internal Mixers (a) Batch Mixers (b) Continuous Mixers Mixing Mill - 2 Smooth Rolls - (If corrugated rolls are used, then use the same service factors that are used for a Cracker-Warmer) Batch Drop Mill - 2 Smooth Rolls Cracker Warmer - 1 Corrugated Roll Cracker - 2 Corrugated Rolls Holding, Feed & Blend Mill - 2 Rolls Refiner - 2 Rolls Calenders Sand Miller Sewage Disposal Bar Screens Chemical Feeders Dewatering Screens Scum Breakers Slow or Rapid Mixers Sludge Collectors Thickeners Vacuum Filters Screens Air Washing Rotary - Stone or Gravel Traveling Water Intake Sugar Industry Beet Slicer Cane Knives Crushers Mills (Low Speed End) Textile Industry Batchers Calenders Cards Dry Cans Dryers Dyeing Machinery Looms Mangles Nappers Pads Slashers Soapers Spinners Tenter Frames Washers Winders v Anti-friction bearings only. NOTE: A service factor of 1.0 may be applied at the base of a super calender, operating over a speed range where part of the range is constant horsepower and part of the range is constant torque, provided that the constant horsepower part is greater than 1.5 to 1. A service factor of 1.25 is applicable to super calenders operating over the entire speed range at contant torque, or where the constant horsepower speed range is less than 1.5 to 1. D-108

109 Series Helical Shaft Mount Speed Reducers Industries q Food and Beverage q Warehousing q Parcel and Package Sortation q Wastewater Treatment q Recycling Applications q Screw Conveyors q Bottling Conveyors q Unit Handling Conveyors q Material Handling Conveyors q De-Watering Conveyors D-109

110 Nom. RPM Nom. Ratio Speed Reducers Motor rpm 1750 Exact Ratio, HP and Torque Series D-110 Shaded ratings are thermally limited to 60 HP. Exact ratio Input H.P. Gear frame Output torque

111 Speed Reducers Motor rpm 1750 (Continued) Exact Ratio, HP and Torque Nom. RPM Nom. Ratio Series Exact ratio Input H.P. Gear frame Output torque D-111

112 Speed Reducers Motor rpm 1450 Exact Ratio, HP and Torque Series Nom. RPM Nom. Ratio D-112 Shaded ratings are thermally limited to 60 HP. Exact ratio Input H.P. Gear frame Output torque

113 Nom. RPM Nom. Ratio Speed Reducers Motor rpm 1450 (Continued) Exact Ratio, HP and Torque Series Exact ratio Input H.P. Gear frame Output torque D-113

114 Series Nom. RPM Nom. Ratio Speed Reducers Motor rpm 1160 Exact Ratio, HP and Torque D-114 Shaded ratings are thermally limited to 60 HP. Exact ratio Input H.P. Gear frame Output torque

115 Nom. RPM Nom. Ratio Speed Reducers Motor rpm 1160 (Continued) Exact Ratio, HP and Torque Series Exact ratio Input H.P. Gear frame Output torque D-115

116 Series Nom. RPM Nom. Ratio Speed Reducers Motor rpm 870 Exact Ratio, HP and Torque D-116 Exact ratio Input H.P. Gear frame Output torque

117 Nom. RPM Nom. Ratio Speed Reducers Motor rpm 870 (Continued) Exact Ratio, HP and Torque Series Exact ratio Input H.P. Gear frame Output torque D-117

118 Series Nom. RPM Nom. Ratio Speed Reducers Combined Motor rpm 1750 Exact Ratio, HP and Torque A A A A A A A A A A A A A A A A A D-118 Exact ratio Input H.P. Gear frame Output torque

119 Nom. RPM Nom. Ratio Speed Reducers Combined Motor rpm 1750 (Continued) Exact Ratio, HP and Torque A A A A A A A A A A A A A A A A A Series Exact ratio Input H.P. Gear frame Output torque D-119

120 C-Face Reducers 31 Double Reduction 40C Finished Bore Face Mount BF1-4 Holes RU XM HY AH YA ØBDX AJ1 AK1 XN HZ O AK 45 D B BB ØAJ A BF 4 Holes Key1 M EH Key U UF UY ØU1 Input Shaft VH VG Output Shaft Gear Frame A B D O HY HZ XN YA XM Output Shaft Gear Frame EH U 2 5 UF UY VG VH Key 3 M /4 Sq. 7/16-14 Series Face Mount Gear Frame C-Face Input AH AJ AK BB BF M8X12 Motor Frame AJ1 AK1 BF1 U1 RU BDX Key1 56C /16 Sq. 143TC/145TC /16 Sq. 1 All rough casting dimensions may vary by up to 0.25" due to casting variations. 2 Output bore tolerance (diameter U ): ", " for all diameters. 3 Key to be supplied by others. 4 Refer to Mounting Accessories on page D-104 for details of Silent-Bloc and Tie Rod kits. 5 Driven shaft entry can be from either side of gear housing by reversing positioning of the snap rings and washer illustrated. D-120

121 C-Face Reducers Double/Triple Reduction 40C Finished Bore Face Mount BF1-4 Holes RU XM HY AH HQ YA Key Key1 1 M VH ØU1 Input Shaft EH U UF UY VG Output Shaft Key ØBDX AJ1 AK1 O XN H - 8 Holes EV 2F B AK HB HA BB BA HZ A HF D ØAJ 45 Typ. BF 4 Holes ØAJ Typ. BF 6 Holes Gear Frame Size - 32 Gear Frame Size BF 6 Holes ØAJ BF ØAJ 60 6 Holes Gear Frame Size - 34 Gear Frame Size - 35 XM Gear Frame A B D 2F H O EV HA HB HF HQ HY HZ 56C- 254TC- XN YA 210TC 180TC 286TC M8X M16X M10X M24X M16X M24X M16X M24X Output Shaft Gear Frame EH U 2, 5, 6 UF UY VG VH Key 3 M /4 Sq. 7/ /16 Sq. 1/ /8 Sq. 5/ /2 Sq. 5/ /8 Sq. 3/4-10 Face Mount Gear Frame AH AJ AK BA BB BF M8X M10X M12X M12X20 C-Face Input Series Motor Frame AJ1 AK1 BF1 U1 RU BDX Key 1 56C /16 Sq. 143TC/145TC /16 Sq. 182TC/184TC /4 Sq. 213TC/W15TC /16 Sq. 254TC/256TC /8 Sq. 284TC/286TC /2 Sq. 1 All rough casting dimensions may vary by up to 0.25" due to casting variations. 2 Output bore tolerance (diameter U ): ", " for all diameters. 3 Key to be supplied by others. 4 Refer to Mounting Accessories on page D-104 for details of Silent-Bloc and Tie Rod kits. 5 Driven shaft entry can be from either side of gear housing by reversing positioning of the snap rings and washer illustrated. 6 Refer to tapered bushed (00B) design where driven shaft size differs from standard finished bore quill size. 7 Use 3242/3243 for "U" = 1.375". Use 3202/3203 for "U" = 1.25". D-121

122 BF 1-4 Holes C-Face Reducers 26 Double/Triple Reduction 00C Finished Bore Shaft Mount 40C Finished Bore Face Mount RU XM HY AH HQ YA AK1 ØBDX AJ1 O XN HZ HB AK Typ. HF HA H - 8 Holes D EV 2F B BB BA A BF 8 Holes Key 1 ØU1 Input Shaft M VH EH VG U UF UY Output Shaft Key Gear Frame A B D 2F H O EV HA HB HF HQ HY HZ XM XN YA M6X M30X Output Shaft Gear Frame EH U 2, 5, 6 UF UY VG VH Key 3 M /8 Sq. 5/8-11 Series Face Mount 7 Gear Frame AH AJ AK BA BB BF M16X25 C-Face Input Motor Frame AJ1 AK1 BF1 U1 RU BDX Key 1 182TC/184TC /4 Sq. 213TC/215TC /16 Sq. 254TC/256TC /8 Sq. 284TC/286TC /2 Sq. 324TC/326TC /2 Sq. 1 All rough casting dimensions may vary by up to 0.25" due to casting variations. 2 Output bore tolerance (diameter U ): ", " for all diameters. 3 Key to be supplied by others. D Refer to Mounting Accessories on page D-104 for details of Silent-Bloc and Tie Rod kits. 5 Driven shaft entry can be from either side of gear housing by reversing positioning of the snap rings and washer illustrated. 6 Refer to tapered bushed (00B) design where driven shaft size differs from standard finished bore quill size. 7 Face dimensions only apply to the 40C Face Mount units.

123 C-Face Reducers Combined (4-6 Reduction Stages) 40C Finished Bore Face Mount RU XM HY AH HQ YA ØBDX AJ1 AK1 O XN AK HB HZ HF Key1 H - 8 Holes HA D M VH EH VG ØU1 Input Shaft U UF UY Output Shaft Key EV 45 Typ. 2F B BB BA Typ. ØAJ BF ØAJ BF 4 Holes 6 Holes Gear Frame Size - 32 Gear Frame Size A BF ØAJ 6 Holes BF ØAJ 60 6 Holes Gear Frame Size - 34 Gear Frame Size - 35 Gear Frame A B D 2F H O EV HA HB HF HQ HY HZ XM 4 Red. 5-6 Red. XN YA M8X M16X M10X M24X M16X M24X M16X M24X Output Shaft Gear Frame EH U 2, 5, 6 UF UY VG VH Key 3 M /4 Sq. 7/ /16 Sq. 1/ /8 Sq. 5/ /2 Sq. 5/ /8 Sq. 3/4-10 Face Mount Gear Frame AH AJ AK BA BB BF M8X M10X M12X M12X20 C-Face Input Motor Frame AJ1 AK1 BF1 U1 RU Frame 32 Frame 33 Frame 34 Frame 35 BDX Key 1 56C /16 Sq. 143TC/145TC /16 Sq. 182TC/184TC /4 Sq. Series 1 All rough casting dimensions may vary by up to 0.25" due to casting variations. 2 Output bore tolerance (diameter U ): ", " for all diameters. 3 Key to be supplied by others. 4 Refer to Mounting Accessories on page D-104 for details of Silent-Bloc and Tie Rod kits. 5 Driven shaft entry can be from either side of gear housing by reversing positioning of the snap rings and washer illustrated. 6 Refer to tapered bushed (00B) design where driven shaft size differs from standard finished bore quill size. 7 Use 3242/3243 for "U" = 1.375". Use 3202/3203 for "U" = 1.25". D-123

124 BF 1-4 Holes RU C-Face Reducers 26 Combined (4-6 Reduction Stages) 00C Finished Bore Shaft Mount 40C Finished Bore Face Mount XM HY AH HQ YA ØBDX AJ1 AK1 O XN HZ HB AK 45 Typ HF HA H - 8 Holes D EV 2F B BB BA A BF 8 Holes Key1 ØU1 Input Shaft M VH EH VG U UF UY Output Shaft Key Gear Frame A B D 2F H O EV HA HB HF HQ HY HZ XM XN YA M6X M30X Output Shaft Gear Frame EH U 2, 5, 6 UF UY VG VH Key 3 M /8 Sq. 5/8-11 Series Face Mount 7 Gear Frame AH AJ AK BA BB BF M16X25 C-Face Input Motor Frame AJ1 AK1 BF1 U1 RU BDX Key 1 56C /16 Sq. 143TC/145TC /16 Sq. 182TC/184TC /4 Sq. 213TC/215TC /16 Sq. 1 All rough casting dimensions may vary by up to 0.25" due to casting variations. 2 Output bore tolerance (diameter U ): ", " for all diameters. 3 Key to be supplied by others. D Refer to Mounting Accessories on page D-104 for details of Silent-Bloc and Tie Rod kits. 5 Driven shaft entry can be from either side of gear housing by reversing positioning of the snap rings and washer illustrated. 6 Refer to tapered bushed (00B) design where driven shaft size differs from standard finished bore quill size. 7 Face dimensions only apply to the 40C Face Mount units.

125 M C-Face Reducers Double/Triple Reduction 50C/60C Finished Bore Flange Mount RU XM BF1-4 HOLES HY YA AH HQ ØBDX AJ1 BE AK1 HZ O XN HB AK ØBD HF HA D H-8 HOLES ØAJ BB BF 4 HOLES EV B 2F BA A EH KEY KEY1 U UF UY ØU1 INPUT SHAFT VH VG OUTPUT SHAFT XM Gear Frame A B D 2F H O EV HA HB HF HQ HY HZ 56C- 254TC- XN YA 210TC 180TC 286TC M8X M16X M10X M24X M16X M24X M16X M24X Output Shaft Gear Frame EH U 2 UF UY VG VH Key 3 M /4 Sq. 7/ /16 Sq. 1/ /8 Sq. 5/ /2 Sq. 5/ /8 Sq. 3/4-10 Flange Mount Gear Frame Flange Code AK AJ BA BB BD BE BF 32 60C C C C C C C C-Face Input Series Motor Frame AJ1 AK1 BF1 U1 RU BDX Key 1 56C /16 Sq. 143TC/145TC /16 Sq. 182TC/184TC /4 Sq. 213TC/215TC /16 Sq. 254TC/256TC /8 Sq. 284TC/286TC /2 Sq. 1 All rough casting dimensions may vary by up to 0.25" due to casting variations. 2 Output bore tolerance (diameter U ): ", " for all diameters. 3 Key to be supplied by others. 4 Driven shaft entry can be from either side of gear housing by reversing positioning of the snap rings and washer illustrated. 7 Use 3242/3243 for "U" = 1.375". Use 3202/3203 for "U" = 1.25". D-125

126 BF 1-4 Holes AK1 ØBDX AJ1 C-Face Reducers 26 Double/Triple Reduction 50C Finished Bore Flange Mount RU XM HY AH HQ YA O XN HZ AK HB ØBD HF HA H - 8 Holes EV 2F B BB BA ØAJ A D BF 8 Holes Key1 Input Shaft ØU1 M VH EH VG U UF Output Shaft UY Key Gear Frame A B D 2F H O EV HA HB HF HQ HY HZ XM XN YA M6X M30X Output Shaft Gear Frame EH U 2 UF UY VG VH Key 3 M /8 Sq. 5/8-11 Series Output Flange Gear Frame Flange Code AJ AK BA AH BB BD BE BF 26 50C C-Face Input Motor Frame AJ1 AK1 BF1 U1 RU BDX Key 1 182TC/184TC /4 Sq. 213TC/215TC /16 Sq. 254TC/256TC /8 Sq. 284TC/286TC /2 Sq. 324TC/326TC /2 Sq. 1 All rough casting dimensions may vary by up to 0.25" due to casting variations. 2 Output bore tolerance (diameter U ): ", " for all diameters. D Key to be supplied by others. 4 Driven shaft entry can be from either side of gear housing by reversing positioning of the snap rings and washer illustrated.

127 M C-Face Reducers Combined (4-6 Reduction Stages) 50C/60C Finished Bore Flange Mount RU XM BF1-4 HOLES HY YA AH HQ ØBDX AK1 AJ1 BE HZ HB O XN ØBD HF AK HA D H-8 HOLES ØAJ BB BF 4 HOLES EV B 2F BA A EH KEY KEY1 U UF UY ØU1 INPUT SHAFT VH VG OUTPUT SHAFT Gear Frame A B D 2F H O EV HA HB HF HQ HY HZ XM 4 Red. 5-6 Red. XN YA M8X M16X M10X M24X M16X M24X M16X M24X Output Shaft Gear Frame EH U 2 UF UY VG VH Key 3 M /4 Sq. 7/ /16 Sq. 1/ /8 Sq. 5/ /2 Sq. 5/ /8 Sq. 3/4-10 Flange Mount Gear Frame Flange Code AK AJ BA BB BD BE BF 32 60C C C C C C C Series C-Face Input Motor Frame AJ1 AK1 BF1 U1 RU BDX Frame 32 Frame 33 Frame 34 Frame 35 Key 1 56C /16 Sq. 143TC/145TC /16 Sq. 182TC/184TC /4 Sq. 1 All rough casting dimensions may vary by up to 0.25" due to casting variations. 2 Output bore tolerance (diameter U ): ", " for all diameters. 3 Key to be supplied by others. 4 Driven shaft entry can be from either side of gear housing by reversing positioning of the snap rings and washer illustrated. 5 Use 3242/3243 for "U" = 1.375". Use 3202/3203 for "U" = 1.25". D-127

128 C-Face Reducers 26 Combined (4-6 Reduction Stages) 50C Finished Bore Flange Mount BF 1-4 Holes RU XM HY AH HQ YA ØBDX AK1 AJ1 O XN AK HB HZ ØBD HF HA H - 8 Holes EV 2F B BB BA ØAJ A D BF 8 Holes Key1 Input Shaft ØU1 M VH EH U UF VG Output Shaft UY Key Gear Frame A B D 2F H O EV HA HB HF HQ HY HZ XM XN YA M6X M30X Output Shaft Gear Frame EH U 2 UF UY VG VH Key 3 M /8 Sq. 5/8-11 Series Flange Mount Gear Frame Flange Code AJ AK BA AH BB BD BE BF 26 50C C-Face Input Motor Frame AJ1 AK1 BF1 U1 RU BDX Key 1 56C /16 Sq. 143TC/145TC /16 Sq. 182TC/184TC /4 Sq. 213TC/215TC /16 Sq. 1 All rough casting dimensions may vary by up to 0.25" due to casting variations. 2 Output bore tolerance (diameter U ): ", " for all diameters. 3 Key to be supplied by others. 4 Driven shaft entry can be from either side of gear housing by reversing positioning of the snap rings and washer illustrated. D-128

129 C-Face Reducers Double/Triple Reduction 00B Tapered Bushed Shaft Mount BF 1-4 Holes RU XM HY YA HQ O ØBDX AJ1 AK1 XN AH HB HZ HF HA D H - 8 Holes EV 2F B XC MC BB BA Key1 A ØU1 Input Shaft XM Gear Frame A B D 2F H O EV HA HB HF HQ HY HZ 56C- 254TC- XN YA 210TC 180TC 286TC M8X M16X M10X M24X M16X M24X M16X M24X Output Shaft Gear Frame BB MC 3 XC Bushing Bores 2 Min. Max /4 1 7/ / / /8 2 7/ / /16 C-Face Input Motor Frame AJ1 AK1 BF1 U1 RU BDX Key 1 56C /16 Sq. 143TC/145TC /16 Sq. 182TC/184TC /4 Sq. 213TC/215TC /16 Sq. 254TC/256TC /8 Sq. 284TC/286TC /2 Sq. Series 1 All rough casting dimensions may vary by up to 0.25" due to casting variations. 2 Refer to Tapered Bushings on page D-100 and D-101 for a listing of all bushing bore sizes available including metric sizes. 3 The MC dimension shows spacing required to install or remove the bushing from the gear unit. 4 Bushing and dust cap can be installed opposite of how they are shown above. 5 Driven shaft entry can be from either side of gear unit housing. Refer in installation manual for requirements. 6 Refer to Mounting Accessories on page D-104 for details of Silent-Bloc and Tie Rod kits. D-129

130 BF 1-4 Holes AK1 ØBDX AJ1 C-Face Reducers 26 Double/Triple Reduction 00B Tapered Bushed Shaft Mount RU XM HY HQ YA O XN HB HZ HF HA H - 8 Holes D BB EV B XC 2F BA Key1 A ØU1 Input Shaft Gear Frame A B D 2F H BA O EV HA HB HF HQ HY HZ XM XN YA M6X M30X Output Shaft Bushing Bores 2 Gear Frame BB XC Min. Max /16 3 7/16 Series C-Face Input Motor Frame AJ1 AK1 BF1 U1 RU BDX Key 1 182TC/184TC /4 Sq. 213TC/215TC /16 Sq. 254TC/256TC /8 Sq. 284TC/286TC /2 Sq. 324TC/326TC /2 Sq. 1 All rough casting dimensions may vary by up to 0.25" due to casting variations. 2 Refer to Tapered Bushings on page D-101 for a listing of all bushing bore sizes available. 3 Refer to Mounting Accessories on page D-104 for details of Silent-Bloc and Tie Rod kits. D-130

131 C-Face Reducers Combined (4-6 Reduction Stages) 00B Tapered Bushed Shaft Mount BF 1-4 Holes RU XM HY YA HQ ØBDX AJ1 AK1 O XN AH HB HZ HF H - 8 Holes EV 2F B XC HA MC BB BA Key1 A D ØU1 Input Shaft Gear Frame A B D 2F H O EV HA HB HF HQ HY HZ XM 4 Red. 5-6 Red. XN YA M8X M16X M10X M24X M16X M24X M16X M24X Output Shaft Gear Frame BB MC 3 XC Bushing Bore 2 Min. Max /4 1 7/ / / /8 2 7/ / /16 C-Face Input Motor Frame AJ1 AK1 BF1 U1 RU Frame 32 Frame 33 Frame 34 Frame 35 BDX Key 1 56C /16 Sq. 143TC/145TC /16 Sq. 182TC/184TC /4 Sq. Series 1 All rough casting dimensions may vary by up to 0.25" due to casting variations. 2 Refer to Tapered Bushings on pages D-100 and D-101 for a listing of all bushing bore sizes available including metric sizes. 3 The MC dimension shows spacing required to install or remove the bushing from the gear unit. 4 Bushing and dust cap can be installed opposite of how they are shown above. 5 Driven shaft entry can be from either side of gear unit housing. Refer in installation manual for requirements. 6 Refer to Mounting Accessories on page D-104 for details of Silent-Bloc and Tie Rod kits. D-131

132 C-Face Reducers 26 Combined (4-6 Reduction Stages) 00B Tapered Bushed Shaft Mount RU XM BF 1-4 Holes HY AH HQ YA ØBDX O AK1 AJ1 XN HB HZ HF HA H - 8 Holes D BB EV B XC 2F BA Key1 A ØU1 Input Shaft Gear Frame A B D 2F H O EV HA HB HF HQ HY HZ XM XN YA M6X M30X Output Shaft Gear Bushing Bore BB XC 2 Frame Min. Max /16 3 7/16 Series C-Face Input Motor Frame AJ1 AK1 BF1 U1 RU BDX Key 1 56C /16Sq. 143TC/145TC /16 Sq. 182TC/184TC /4 Sq. 213TC/215TC /16 Sq. 1 All rough casting dimensions may vary by up to 0.25" due to casting variations. 2 Refer to Tapered Bushings on pages D-100 and D-101 for a listing of all bushing bore sizes available. 3 Refer to Mounting Accessories on page D-104 for details of Silent-Bloc and Tie Rod kits. D-132

133 BF 1-4 Holes ØBDX AK1 AJ1 C-Face Reducers Double/Triple Reduction 00S CEMA Screw Conveyor Drive RU XM BB AH S T HQ YA 4 Tapped Holes and Slots for "W" Dia. Trough End Fasteners O XN ØJ L/2 HF U L D B XC Trough End L/2 L A Key1 S AH2 T ØU1 Input Shaft T2 ØJ U Trough End Optional 3 Hole Shaft XM Gear Frame A B D O HF HQ XC 56C - 145TC 182TC -215TC 254TC - 286TC XN YA BB M16X M24X M24X M24X Screw Conveyor Gear Frame U Screw Dia. W J L S T T2 AH AH C-Face Input Motor Frame AJ1 AK1 BF1 U1 RU BDX Key 1 56C /16 Sq. 143TC/145TC /16 Sq. 182TC/184TC /4 Sq. 213TC/215TC /16 Sq. 254TC/256TC /8 Sq. 284TC/286TC /2 Sq. Series 1 All rough casting dimensions may vary by up to 0.25" due to casting variations. 2 Refer to pages D-102 and D-103 for a the screw conveyor drive shafts, trough ends and other accessories available for each frame size. 3 Thrust ratings for each gear frame size is listed on page D-102. D-133

134 BF 1-4 Holes ØBDX AJ1 AK1 C-Face Reducers Combined (4-6 Reduction Stages) 00S CEMA Screw Conveyor Drive RU XM BB AH S T HQ YA 4 Tapped Holes and Slots for "W" Dia. Trough End Fasteners. O XN ØJ U HF L/2 L D B XC Trough End L/2 L A Key1 S T AH2 ØU1 Input Shaft T2 ØJ U Trough End Optional 3 Hole Shaft Gear Frame A B D O HF HQ XC XM 4 Red. 5-6 Red. XN YA BB M16X M24X M24X M24X Screw Conveyor Series Gear Frame U Screw Dia. W J L S T T2 AH AH C-Face Input Motor Frame AJ1 AK1 BF1 U1 RU Frame 32 Frame 33 Frame 34 Frame 35 BDX Key 1 56C /16 Sq. 143TC/145TC /16 Sq. 182TC/184TC /4 Sq. 1 All rough casting dimensions may vary by up to 0.25" due to casting variations. 2 Refer to pages D-102 and D-103 for a the screw conveyor drive shafts, trough ends and other accessories available for each frame size. 3 Thrust ratings for each gear frame size is listed on page D-102. D-134

135 Input Shaft Reducer 26 Double/Triple Reduction 00C Finished Bore Shaft Mount 40C Finished Bore Face Mount RU XM HY AH HQ YA Key1 UY1 V1 Input Shaft U1 O XN HA AK HB HZ HF M VH EH VG U UF UY Output Shaft Key H - 8 Holes EV 2F B BB BA Typ. A D 45 ØAJ BF 4 Holes ØAJ BF 8 Holes Gear Frame Size - 21 Gear Frame Size - 26 Gear Frame A B D 2F H O EV HA HB HF HQ HY HZ XM XN YA M6X M30X Output Shaft Gear Frame EH U 256 UF UY VG VH Key 3 M /8 Sq. 5/8-11 Face Mount 7 Gear Frame AH AJ AK BA BB BF M16X25 Input Shaft Series Gear Frame RU U1 UY1 V1 Key /2 Sq. 1 All rough casting dimensions may vary by up to 0.25" due to casting variations. 2 Output bore tolerance (diameter U ): ", " for all diameters. 3 Key to be supplied by others. 4 Refer to Mounting Accessories on page D-104 for details of Silent-Bloc and Tie Rod kits. 5 Driven shaft entry can be from either side of gear housing by reversing positioning of the snap rings and washer illustrated. 6 Refer to tapered bushed (00B) design where driven shaft size differs from standard finished bore quill size. 7 Face dimensions only apply to the 40C Face Mount units. D-135

136 Input Shaft Reducer Double/Triple Reduction 40C Finished Bore Face Mount Key1 UY1 M VH Input Shaft EH VG V1 O U1 UF XN Output Shaft RU H - 8 Holes EV UY XM B 2F HY AH AK HB HA BB BA HZ HQ 45 Typ. ØAJ BF 4 Holes Gear Frame Size - 31, U Key 60 ØAJ BF 6 Holes Gear Frame Size - 34 YA A HF D Typ. ØAJ BF 6 Holes Gear Frame Size BF 6 Holes 60 ØAJ Gear Frame Size - 35 Series Gear Frame A B D 2F H O EV HA HB HF HQ HY HZ XM XN YA N/A N/A N/A N/A N/A 5.14 M16X M8X M16X M10X M24X M16X M24X M16X M24X Output Shaft Gear Frame EH U UF UY VG VH KEY 3 M /4 Sq. 7/ /16 Sq 1/ /4 Sq. 7/ /8 Sq 5/ /2 Sq 5/ /8 Sq 3/4-10 Face Mount Gear Frame AH AJ AK BA BB BF Input Shaft N/A 0.14 M8X M8X M10X M12X M12X20 Gear Frame RU U1 UY1 V1 Key /16 Sq /16 Sq /4 Sq /4 Sq /16 Sq 1 All rough casting dimensions may vary by up to 0.25" due to casting variations. 2 Output bore tolerance (diameter U ): ", " for 31, / " for Key to be supplied by others. 4 Refer to Mounting Accessories on page D-104 for details of Silent-Bloc and Tie Rod kits. 5 Driven shaft entry can be from either side of gear housing by reversing positioning of the snap rings and washer illustrated. 6 Refer to tapered bushed (00B) design where driven shaft size differs from standard finished bore quill size. (except frame 31). 7 Use 3242/3243 for "U" = 1.375". Use 3202/3203 for "U" = 1.25". D-136

137 Input Shaft Reducer Combined (4-6 Reduction Stages) 40C Finished Bore Face Mount RU XM HY AH HQ YA XN HZ O XN AK HB HF Flat FW V1 FL Input Shaft Frame 32 and 33 H - 8 Holes Key1 UY1 EV V1 Input Shaft 2F B BB BA HA 45 Typ. ØAJ BF 4 Holes Gear Frame Size - 32 A D Typ. ØAJ BF 6 Holes Gear Frame Size - 33 M VH EH VG U UF UY Output Shaft Key ØAJ BF 6 Holes Gear Frame Size BF 6 Holes 60 ØAJ Gear Frame Size - 35 Gear Frame A B D 2F H O EV HA HB HF HQ HY HZ XM 4 Red. 5-6 Red. XN YA M8X M16X M10X M24X M16X M24X M16X M24X Output Shaft Gear Frame EH U 2, 5, 6 UF UY VG VH Key 3 M /4 Sq. 7/ /16 Sq. 1/ /8 Sq. 5/ /2 Sq. 5/ /8 Sq. 3/4-10 Face Mount Gear Frame AH AJ AK BA BB BF M8X M10X M12X M12X20 Input Shaft Gear Frame RU U1 FL FW UY1 V1 Key /16 Sq /16 Sq. Series 1 All rough casting dimensions may vary by up to 0.25" due to casting variations. 2 Output bore tolerance (diameter U ): ", " for all diameters. 3 Key to be supplied by others. 4 Refer to Mounting Accessories on page D-104 for details of Silent-Bloc and Tie Rod kits. 5 Driven shaft entry can be from either side of gear housing by reversing positioning of the snap rings and washer illustrated. 6 Refer to tapered bushed (00B) design where driven shaft size differs from standard finished bore quill size. D-137

138 Input Shaft Reducer 26 Combined (4-6 Reduction Stages) 00C Finished Bore Shaft Mount 40C Finished Bore Face Mount RU XM HY AH HQ YA U1 O XN HZ HB 45 Typ HF AK HA H - 8 Holes D EV B 2F BB BA A BF 8 Holes Key1 UY1 Input Shaft V1 M VH EH VG U UF UY Output Shaft Key Gear Frame A B D 2F H O EV HA HB HF HQ HY HZ XM XN YA M6X M30X Output Shaft Series Gear Frame EH U 2, 5, 6 UF UY VG VH Key 3 M /8 Sq. 5/8-11 Face Mount 7 Gear Frame AH AJ AK BA BB BF M16X25 Input Shaft Gear Frame RU U1 UY1 V1 Key /2 Sq. 1 All rough casting dimensions may vary by up to 0.25" due to casting variations. 2 Output bore tolerance (diameter U ): ", " for all diameters. 3 Key to be supplied by others. D Refer to Mounting Accessories on page D-104 for details of Silent-Bloc and Tie Rod kits. 5 Driven shaft entry can be from either side of gear housing by reversing positioning of the snap rings and washer illustrated. 6 Refer to tapered bushed (00B) design where driven shaft size differs from standard finished bore quill size. 7 Face dimensions only apply to the 40C Face Mount units.

139 Input Shaft Reducer Double/Triple Reduction 50C/60C Finished Bore Flange Mount RU XM HY YA AH HQ U1 BE HZ O XN HB AK ØBD HF HA D H - 8 Holes EV Key1 UY1 2F B Input Shaft BA V1 BB M VH ØAJ EH VG A U UF UY Output Shaft BF 4 Holes Key Gear Frame A B D 2F H O AH EV HA HB HF HQ HY HZ XM XN YA M8X M16X M10X M24X M16X M24X M16X M24X Output Shaft Gear Frame EH U 2 UF UY VG VH Key 3 M /4 Sq. 7/ /16 Sq. 1/ /8 Sq. 5/ /2 Sq. 5/ /8 Sq. 3/4-10 Output Flange Gear Frame Flange Code AK AJ BA BB BD BE BF 32 60C C C C C C C Series Input Shaft Gear Frame RU U1 UY1 V1 Key /16 Sq /4 Sq /4 Sq /16 Sq. 1 All rough casting dimensions may vary by up to 0.25" due to casting variations. 2 Output bore tolerance (diameter U ): ", " for all diameters. 3 Key to be supplied by others. 4 Use 3242/3243 for "U" = 1.375". Use 3202/3203 for "U" = 1.25". 5 Driven shaft entry can be from either side of gear housing. D-139

140 Input Shaft Reducer 26 Double/Triple Reduction 50C Finished Bore Flange Mount RU XM HY AH HQ YA U1 BE O XN HB AK HZ ØBD HF HA H - 8 Holes EV Key1 UY1 B 2F V1 Input Shaft BB BA M VH ØAJ A EH U UF UY VG Output Shaft Key D BF 8 Holes Gear Frame A B D 2F H O AH EV HA HB HF HQ HY HZ XM XN YA M6X M30X Output Shaft Gear Frame EH U 2 UF UY VG VH Key 3 M /8 Sq. 5/8-11 Series Output Flange Gear Frame Flange Code AJ AK BA AH BB BD BE BF 26 50C Input Shaft Gear Frame RU U1 UY1 V1 Key /2 Sq. 1 All rough casting dimensions may vary by up to 0.25" due to casting variations. 2 Output bore tolerance (diameter U ): ", " for all diameters. D Key to be supplied by others. 4 Driven shaft entry can be from either side of gear housing.

141 Input Shaft Reducer Combined (4-6 Reduction Stages) 50C Finished Bore Flange Mount RU XM HY YA AH HQ O U1 XN BE HZ HB AK ØBD HF H - 8 Holes HA ØAJ D EV 2F B BA BB A BF 4 Holes Key1 UY1 V1 M EH U UF UY Key Input Shaft VH VG Output Shaft Gear Frame A B D 2F H O AH EV HA HB HF HQ HY HZ XM 4 Red. 5-6 Red. XN YA M8X M16X M10X M24X M16X M24X M16X M24X Output Shaft Gear Frame EH U 2 UF UY VG VH Key 3 M /4 Sq. 7/ /16 Sq. 1/ /8 Sq. 5/ /2 Sq. 5/ /8 Sq. 3/4-10 Output Flange Gear Frame Flange Code AK AJ BA BB BD BE BF 32 60C C C C C C C Series Input Shaft Gear Frame RU U1 FL FW UY1 V1 Key /16 Sq /16 Sq. 1 All rough casting dimensions may vary by up to 0.25" due to casting variations. 2 Output bore tolerance (diameter U ): ", " for all diameters. 3 Key to be supplied by others. 4 Use 3242/3243 for "U" = 1.375". Use 3202/3203 for "U" = 1.25". 5 Driven shaft entry can be from either side of gear housing. D-141

142 Input Shaft Reducer 26 Combined (4-6 Reduction Stages) 50C Finished Bore Flange Mount RU XM HY AH HQ YA U1 O XN BE HB AK HZ ØBD HF HA H - 8 Holes EV 2F B BB BA ØAJ A D BF 8 Holes Key1 UY1 Input Shaft V1 M VH EH VG U UF UY Output Shaft Key Gear Frame A B D 2F H O AH EV HA HB HF HQ HY HZ XM XN YA M6X M30X Output Shaft Gear Frame EH U 2 UF UY VG VH Key 3 M /8 Sq. 5/8-11 Series Output Flange Gear Frame Flange Code AJ AK BA BB BD BE BF 26 50C Input Shaft Gear Frame RU U1 UY1 V1 Key /4 Sq. 1 All rough casting dimensions may vary by up to 0.25" due to casting variations. 2 Output bore tolerance (diameter U ): ", " for all diameters. 3 Key to be supplied by others. 4 Driven shaft entry can be from either side of gear housing by reversing positioning of the snap rings and washer illustrated. D-142

143 Input Shaft Reducer Double/Triple Reduction 00B Tapered Bushed Shaft Mount RU XM HY YA HQ O U1 XN HB HZ HF HA D H - 8 Holes EV 2F B XC MC BB BA Key1 V1 A UY1 Input Shaft Gear Frame A B D 2F H O BA EV HA HB HF HQ HY HZ XM XN YA M8X M16X M10X M24X M16X M24X M16X M24X Output Shaft Gear Frame BB MC 3 XC Bushing Bore 2 Min. Max /4 1 7/ / / /8 2 7/ / /16 Input Shaft Gear Frame RU U1 UY1 V1 Key /16 Sq /4 Sq /4 Sq /16 Sq. Series 1 All rough casting dimensions may vary by up to 0.25" due to casting variations. 2 Refer to Tapered Bushings on pages D-100 and D-101 for a listing of all bushing bore sizes available. 3 The MC dimension shows spacing required to install or remove the bushing from the gear unit. 4 Bushing and dust cap can be installed opposite of how they are shown above. 5 Driven shaft entry can be from either side of gear unit housing. Refer to installation manual for requirements. 6 Refer to Mounting Accessories on page D-104 for details of Silent-Bloc and Tie Rod kits. D-143

144 Input Shaft Reducer 26 Double/Triple Reduction 00B Tapered Bushed Shaft Mount RU XM HY YA HQ U1 O XN HB HZ HF HA H - 8 Holes D BB EV 2F B XC BA Key1 V1 A UY1 Input Shaft Gear Frame A B D 2F H O BA EV HA HB HF HQ HY HZ XM XN YA M6X M30X Output Shaft Bushing Bore Gear Frame BB XC 2 Min. Max /16 3 7/16 Series Input Shaft Gear Frame RU U1 UY1 V1 Key /2 Sq. 1 All rough casting dimensions may vary by up to 0.25" due to casting variations. 2 Refer to Tapered Bushings on pages D-100 and D-101 for a listing of all bushing bore sizes available. 3 Refer to Mounting Accessories on page D-104 for details of Silent-Bloc and Tie Rod kits. D-144

145 Input Shaft Reducer Combined (4-6 Reduction Stages) 00B Tapered Bushed Shaft Mount RU XM HY HQ YA U1 HZ O XN HB HF HA D H - 8 Holes EV 2F B XC BB BA MC Key1 V1 A UY1 Input Shaft Gear Frame A B D 2F H O BA EV HA HB HF HQ HY HZ XM 4 Red. 5-6 Red. XN YA M8X M16X M10X M24X M16X M24X M16X M24X Output Shaft Gear Frame BB MC 3 XC Bushing Bore 2 Min. Max /4 1 7/ / / /8 2 7/ / /16 Input Shaft Gear Frame RU U1 FL FW UY1 V1 Key /16 Sq /16 Sq. Series 1 All rough casting dimensions may vary by up to 0.25" due to casting variations. 2 Refer to Tapered Bushings on pages D-100 and D-101 for a listing of all bushing bore sizes available including metric sizes. 3 The MC dimension shows spacing required to install or remove the bushing from the gear unit. 4 Bushing and dust cap can be installed opposite of how they are shown above. 5 Driven shaft entry can be from either side of gear unit housing. Refer to installation manual for requirements. 6 Refer to Mounting Accessories on page D-104 for details of Silent-Bloc and Tie Rod kits. D-145

146 Input Shaft Reducer 26 Combined (4-6 Reduction Stages) 00B Tapered Bushed Shaft Mount RU XM HY YA HQ U1 O XN HB HZ HF HA H - 8 Holes D EV BB 2F BA B XC V1 Key1 UY1 Input Shaft A Gear Frame A B D 2F H O BA EV HA HB HF HQ HY HZ XM XN YA M6X M30X Output Shaft Bushing Bore Gear Frame BB XC 2 Min. Max /16 3 7/16 Series Input Shaft Gear Frame RU U1 UY1 V1 Key /4 Sq. 1 All rough casting dimensions may vary by up to 0.25" due to casting variations. 2 Refer to Tapered Bushings on pages D-100 and D-101 for a listing of all bushing bore sizes available in each gear frame size. 3 Refer to Mounting Accessories on page D-104 for details of Silent-Bloc and Tie Rod kits. D-146

147 Input Shaft Reducer Double/Triple Reduction 00S CEMA Screw Conveyor Drive RU XM HY BB AH S T HQ YA 4 Tapped Holes and Slots for "W" Dia. Trough End Fasteners U1 HZ O XN ØJ U L/2 L HF D XC B Trough End L/S L A AH2 S T Key1 UY1 V1 Input Shaft T2 ØJ U Trough End Optional 3 Hole Shaft Gear Frame A B D O HF HQ HY HZ XC XM XN YA BB M16X M24X M24X M24X Screw Conveyor Gear Frame Screw Dia. W J L U S T T2 AH AH2 32, Input Shaft Gear Frame RU U1 UY1 V1 Key /16 Sq /4 Sq /4 Sq /16 Sq. Series 1 All rough casting dimensions may vary by up to 0.25" due to casting variations. 2 Refer to pages D-102 and D-103 for the screw conveyor drive shafts, trough ends and other accessories available for each frame size. 3 Thrust ratings for each gear frame size are listed on page D-102. D-147

148 Input Shaft Reducer Combined (4-6 Reduction Stages) 00S CEMA Screw Conveyor Drive RU XM HY BB AH S T HQ YA 4 Tapped Holes and Slots for "W" Dia. Trough End Fasteners U1 HZ O XN ØJ HF L/2 U L D B XC Trough End L/2 L A Flat FW V1 FL Input Shaft Frame 32 and 33 Only Key1 UY1 Input Shaft V1 S AH2 T ØJ U T2 Trough End Optional 3 Hole Shaft Gear Frame A B D O HF HQ HY HZ XC XM 4 Red. 5-6 Red. XN YA M16X M24X M24X M24X Series Screw Conveyor Gear Frame Screw Dia. J L U S T T2 AH AH2 BB 32, Input Shaft Gear Frame RU U1 FL FW UY1 V1 Key /16 Sq /16 Sq. 1 All rough casting dimensions may vary by up to 0.25" due to casting variations. 2 Refer to pages D-102 and D-103 for the screw conveyor drive shafts, trough ends and other accessories available for each frame size. D Thrust ratings for each gear frame size are listed on page D-102.

149 Key1 UY1 Input Shaft V1 Scoop Mount Reducer Double/Triple Reduction 40C Finished Bore Face Mount XL U1 RU XM HY AH HQ YA M VH EH U UF VG Output Shaft UY Key O XN XH H - 8 Holes EV 2F B AK HB HA BB BA HZ A XW HF D ØAJ 45 Typ. BF 4 Holes Gear Frame Size Typ. ØAJ BF 6 Holes Gear Frame Size - 33 ØAJ BF 6 Holes 60 BF 6 Holes ØAJ Gear Frame Size - 34 Gear Frame Size Gear Frame A B D 2F H O EV HA HB HF HQ HY HZ XM XN YA M8X M16X M10X M24X M16X M24X M16X M24X Output Shaft Gear Frame EH U 2, 5, 6 UF UY VG VH Key 3 M /16 Sq. 1/ /8 Sq. 5/ /2 Sq. 5/ /8 Sq. 3/4-10 Face Mount Gear Frame AH AJ AK BA BB BF M8X M10X M12X M12X20 Input Shaft Gear Frame RU U1 UY1 V1 Key /16 Sq /4 Sq /4 Sq /16 Sq. Motor Frame Gear Frame T 182T-184T 213T-215T XH XL XW XH XL XW XH XL XW Series 1 All rough casting dimensions may vary by up to 0.25" due to casting variations. 2 Output bore tolerance (diameter U ): ", " for all diameters. 3 Key to be supplied by others. 4 Refer to Mounting Accessories on page D-104 for details of Silent-Bloc and Tie Rod kits. 5 Driven shaft entry can be from either side of gear housing by reversing positioning of the snap rings and washer illustrated. 6 Refer to tapered bushed (00B) design where driven shaft size differs from standard finished bore quill size /3243 D-149

150 Scoop Mount Reducer 26 Double/Triple Reduction 00C Finished Bore Shaft Mount 40C Finished Bore Face Mount XL RU XM HY AH HQ YA XN XH AK HZ HB O Typ. HF HA H - 8 Holes EV 2F B BB BA A XW D BF 8 Holes Key1 UY1 Input Shaft V1 M VH EH U UF VG Output Shaft UY Key Gear Frame A B D 2F H O EV HA HB HF HQ HY HZ XM XN YA M6X M30X Output Shaft Gear Frame EH U 2, 5, 6 UF UY VG VH Key 3 M /8 Sq. 5/8-11 Series Face Mount 7 Gear Frame AH AJ AK BA BB BF M16X25 Input Shaft Gear Frame RU U1 UY1 V1 Key /2 Sq. Motor Frame 182T-184T 213T-215T 254T-256T 284T-286T 324T-326T Gear Frame XH XL XW XH XL XW XH XL XW XH XL XW XH XL XW All rough casting dimensions may vary by up to 0.25" due to casting variations. 2 Output bore tolerance (diameter U ): ", " for all diameters. 3 Key to be supplied by others. 4 Refer to Mounting Accessories on page D-104 for details of Silent-Bloc and Tie Rod kits. 5 Driven shaft entry can be from either side of gear housing by reversing positioning of the snap rings and washer illustrated. 6 Refer to tapered bushed (00B) design where driven shaft size differs from standard finished bore quill size. 7 Face dimensions only apply to the 40C Face Mount units. D-150

151 XL RU Scoop Mount Reducer 26 Combined (4-6 Reduction Stages) 00C Finished Bore Shaft Mount 40C Finished Bore Face Mount XM HY AH HQ YA U1 O XN XH HZ HB AK Typ. HF HA H - 8 Holes EV 2F B BB BA A XW D BF 8 Holes Key1 UY1 Input Shaft V1 M VH EH VG U UF Output Shaft UY Key Gear Frame A B D 2F H O EV HA HB HF HQ HY HZ XM XN YA M6X M30X Output Shaft Gear Frame EH U 2, 5, 6 UF UY VG VH Key 3 M /8 Sq. 5/8-11 Face Mount 7 Gear Frame AH AJ AK BA BB BF M16X25 Input Shaft Gear Frame RU U1 UY1 V1 Key /4 Sq. Motor Frame 143T-145T 182T-184T Gear Frame XH XL XW XH XL XW Series 1 All rough casting dimensions may vary by up to 0.25" due to casting variations. 2 Output bore tolerance (diameter U ): ", " for all diameters. 3 Key to be supplied by others. 4 Refer to Mounting Accessories on page D-104 for details of Silent-Bloc and Tie Rod kits. 5 Driven shaft entry can be from either side of gear housing by reversing positioning of the snap rings and washer illustrated. 6 Refer to tapered bushed (00B) design where driven shaft size differs from standard finished bore quill size. 7 Face dimensions only apply to the 40C Face Mount units. D-151

152 Scoop Mount Reducer Double/Triple Reduction 50C/60C Finished Bore Flange Mount Key1 V1 XL RU XM HY AH HQ YA UY1 Input Shaft O XN XH U1 BE HZ HB AK ØBD HF M VH EH VG U UF UY Output Shaft Key H - 8 Holes EV 2F B BA HA BB ØAJ A XW D BF 4 Holes Gear Frame A B D 2F H O AH EV HA HB HF HQ HY HZ XM XN YA M8X M16X M10X M24X M16X M24X M16X M24X Output Shaft Gear Frame EH U 2 UF UY VG VH Key 3 M /16 Sq. 1/ /8 Sq. 5/ /2 Sq. 5/ /8 Sq. 3/4-10 Output Flange Series Gear Frame Flange Code AK AJ BA BB BD BE BF 32 60C C C C C C C Input Shaft Gear Frame RU U1 UY1 V1 Key /16 Sq /4 Sq /4 Sq /16 Sq. Motor Frame Gear Frame Flange T 182T-184T 213T-215T Code XH XL XW XH XL XW XH XL XW 32 60C C C C C C C All rough casting dimensions may vary by up to 0.25" due to casting variations. 2 Output bore tolerance (diameter U ): ', " for all diameters. D Key to be supplied by others. 4 Driven shaft entry can be from either side of gear housing by reversing positioning of the snap rings and washer illustrated /3243

153 Scoop Mount Reducer 26 Double/Triple Reduction 50C Finished Bore Flange Mount XL RU XM HY AH HQ YA U1 XN XH AK HB HZ O ØBD HF HA H - 8 Holes EV 2F B BB BA ØAJ A D BF 8 Holes Key1 UY1 Input Shaft V1 M VH EH VG U UF Output Shaft UY Key Gear Frame A B D 2F H O AH EV HA HB HF HQ HY HZ XM XN YA M6X M30X Output Shaft Gear Frame EH U 2 UF UY VG VH Key 3 M /8 Sq. 5/8-11 Output Flange Gear Frame Flange Code AJ AK BA BB BD BE BF 26 50C Input Shaft Gear Frame RU U1 UY1 V1 Key /2 Sq. Motor Frame 182T-184T 213T-215T 254T-256T 284T-286T 324T-326T Gear Frame XH XL XW XH XL XW XH XL XW XH XL XW XH XL XW Series 1 All rough casting dimensions may vary by up to 0.25" due to casting variations. 2 Output bore tolerance (diameter U ): ", " for all diameters. 3 Key to be supplied by others. 4 Driven shaft entry can be from either side of gear housing by reversing positioning of the snap rings and washer illustrated. D-153

154 Scoop Mount Reducer 26 Combined (4-6 Reduction Stages) 50C Finished Bore Flange Mount XL RU XM HY AH HQ YA U1 O XN XH AK HB HZ ØBD HF HA H - 8 Holes EV 2F B BB BA ØAJ A D BF 8 Holes Key1 UY1 Input Shaft V1 M VH EH U UF VG Output Shaft UY Key Gear Frame A B D 2F H O AH EV HA HB HF HQ HY HZ XM XN YA M6X M30X Output Shaft Gear Frame EH U 2 UF UY VG VH Key 3 M /8 Sq. 5/8-11 Series Output Flange Gear Frame Flange Code AJ AK BA BB BD BE BF 26 50C Input Shaft Gear Frame RU U1 UY1 V1 Key /4 Sq. Motor Frame 143T-145T 182T-184T Gear Frame XH XL XW XH XL XW All rough casting dimensions may vary by up to 0.25" due to casting variations. 2 Output bore tolerance (diameter U ): ", " for all diameters. 3 Key to be supplied by others. 4 Driven shaft entry can be from either side of gear housing by reversing positioning of the snap rings and washer illustrated. D-154

155 Scoop Mount Reducer Double/Triple Reduction 00B Tapered Bushed Shaft Mount XL RU XM HY HQ YA Key1 UY1 V1 O XN XH U1 AH HB HZ HF Input Shaft H - 8 Holes EV 2F B XC HA MC BB BA A XW D Gear Frame A B D 2F H O BA EV HA HB HF HQ HY HZ XM XN YA M8X M16X M10X M24X M16X M24X M16X M24X Output Shaft Gear Frame BB MC 3 XC Bushing Bore 2 Min. Max /4 1 7/ / / /8 2 7/ / /16 Input Shaft Gear Frame RU U1 UY1 V1 Key /16 Sq /4 Sq /4 Sq /16 Sq. Motor Frame Gear Frame T 182T-184T 213T-215T XH XL XW XH XL XW XH XL XW Series 1 All rough casting dimensions may vary by up to 0.25" due to casting variations. 2 Refer to Tapered Bushings on pages D-100 and D-101 for a listing of all bushing bore sizes available including metric sizes. 3 The MC dimension shows spacing required to install or remove the bushing from the gear unit. 4 Bushing and dust cap can be installed opposite of how they are shown above. 5 Driven shaft entry can be from either side of gear housing. Refer to installation manual for requirements. 6 Refer to Mounting Accessories on page D-104 for details of Silent- Bloc and Tie Rod kits. D-155

156 Scoop Mount Reducer 26 Double/Triple Reduction 00B Tapered Bushed Shaft Mount XL RU XM HY AH HQ YA Key1 UY1 Input Shaft V1 O XN XH HB HA HZ HF H - 8 Holes D EV 2F B XC BB BA A XW Gear Frame A B D 2F H O BA EV HA HB HF HQ HY HZ XM XN YA M6X M30X Output Shaft Bushing Bores Gear Frame BB XC 2 Min. Max /16 3 7/16 Series Input Shaft Gear Frame RU U1 UY1 V1 Key /2 Sq. Motor Frame 182T-184T 213T-215T 254T-256T 284T-286T 324T-326T Gear Frame XH XL XW XH XL XW XH XL XW XH XL XW XH XL XW All rough casting dimensions may vary by up to 0.25" due to casting variations. 2 Refer to Tapered Bushings on pages D-100 and D-101 for a listing of all bushing bore sizes available. 3 Refer to Mounting Accessories on page D-104 for details of Silent- Bloc and Tie Rod kits. D-156

157 Scoop Mount Reducer 26 Combined (4-6 Reduction Stages) 00B Tapered Bushed Shaft Mount XL RU XM HY AH HQ YA U1 Key1 UY1 Input Shaft V1 XN O XH H - 8 Holes HB HA HZ HF D EV 2F B XC BB BA A XW Gear Frame A B D 2F H O BA EV HA HB HF HQ HY HZ XM XN YA M6X M30X Output Shaft Bushing Bores Gear Frame BB XC 2 Min. Max /16 3 7/16 Input Shaft Gear Frame RU U1 UY1 V1 Key /4 Sq. Motor Frame 143T-145T 182T-184T Gear Frame XH XL XW XH XL XW Series 1 All rough casting dimensions may vary by up to 0.25" due to casting variations. 2 Refer to Tapered Bushings on pages D-100 and D-101 for a listing of all bushing bore sizes available in each gear frame size. 3 Refer to Mounting Accessories on page D-104 for details of Silent- Bloc and Tie Rod kits. D-157

158 O XH XN Scoop Mount Reducer Double/Triple Reduction 00S CEMA Screw Conveyor Drive U1 XL RU XM HY BB AH S T ØJ U HQ HZ YA XW L/2 L 4 Tapped Holes and Slots for "W" Dia. Trough End Fasteners HF D B XC Trough End L/2 L A S AH2 T Key1 V1 ØJ UY1 Input Shaft T2 U Trough End Optional 3 Hole Shaft Gear Frame A B D O HF HQ HY HZ XC XM XN YA BB M16X M24X M24X M24X Screw Conveyor Series Gear Frame Screw Dia. W J L U S T T2 AH AH2 32, Input Shaft Gear Frame RU U1 UY1 V1 Key /16 Sq /4 Sq /4 Sq /16 Sq. Motor Frame Gear Frame T 182T-184T 213T-215T XH XL XW XH XL XW XH XL XW All rough casting dimensions may vary by up to 0.25" due to casting variations. 2 Refer pages D-102 and D-193 for the screw conveyor drive shafts, trough ends and other accessories available for each frame size. D Thrust ratings for each gear frame size are listed on page D-102.

159 Top Mount Reducer Double/Triple Reduction 40C Finished Bore Face Mount TL TW Key1 UY1 U1 Input Shaft V1 HT Center Distance HS LS HY AH 9.00 YA M VH EH VG U UF UY Output Shaft 45 Typ. Key XN EV RU Typ. 2F B C HZ HB AK HA H - 8 Holes BB BA ØAJ BF ØAJ ØAJ 4 Holes BF BF 6 Holes 6 Holes Gear Frame Size - 32 Gear Frame Size - 33 Gear Frame Size - 34 HFO D A BF 6 Holes 60 ØAJ Gear Frame Size - 35 Gear HT A B D 2F H O EV HA HB HF HQ HY HZ XM XN YA LS HS TL TW Frame Min. Max M8X M16X M10X M24X M16X M24X M16X M24X Output Shaft Gear Frame EH U 2, 5, 6 UF UY VG VH Key 3 M /16 Sq. 1/ /8 Sq. 5/ /2 Sq. 5/ /8 Sq. 3/4-10 Output Face Gear Frame AH AJ AK BA BB BF M8X M10X M12X M12X20 Input Shaft Gear Frame RU U1 UY1 V1 Key /16 Sq /4 Sq /4 Sq /16 Sq Motor Frame Center Distance Center Distance Center Distance Center Distance Min. Max. Min. Max. Min. Max. Min. Max T/145T T/184T T/215T T/256T T/286T Series 1 All rough casting dimensions may vary by up to 0.25" due to casting variations. 2 Output bore tolerance (diameter U ): ', " for all diameters. 3 Key to be supplied by others. 4 Refer to Mounting Accessories on page D-104 for details of Silent-Bloc and Tie Rod kits. 5 Driven shaft entry can be from either side of gear housing by reversing positioning of the snap rings and washer illustrated. 6 Refer to tapered bushed (00B) design where driven shaft size differs from standard finished bore quill size /3243 D-159

160 Top Mount Reducer Double/Triple Reduction 50C/60C Finished Bore Flange Mount TL TW M VH Key1 UY1 EH VG V1 U1 Input Shaft U UF UY Output Shaft Key HT Center Distance LS HS XN H - 8 Holes EV RU 2F B C HY AH BE HB AK HA BB BA 9.00 HZ ØBD ØAJ YA A HF O D BF 4 Holes Gear HT A B D 2F H O AH EV HA HB HF HQ HY HZ XM XN YA LS HS TL TW Frame Min. Max M8X M16X M10X M24X M16X M24X M16X M24X Output Shaft Series Gear Frame EH U 2 UF UY VG VH Key 3 M /4 Sq. 7/ /16 Sq. 1/ /8 Sq. 5/ /2 Sq. 5/ /8 Sq. 3/4-10 Output Flange Gear Frame Flange Code AK AJ BA BB BD BE BF 60C C C C C C C Input Shaft Gear Frame RU U1 UY1 V1 Key /16 Sq /4 Sq /4 Sq /16 Sq Motor Frame Center Distance Center Distance Center Distance Center Distance Min. Max. Min. Max. Min. Max. Min. Max T/145T T/184T T/215T T/256T T/286T All rough casting dimensions may vary by up to 0.25" due to casting variations. 2 Output bore tolerance (diameter U ): ', " for all diameters. D Key to be supplied by others. 4 Driven shaft entry can be from either side of gear housing by reversing positioning of the snap rings and washer illustrated. 5 Use 3242/3243 for "U" = 1.375". Use 3202/3203 for "U" = 1.25".

161 Top Mount Reducer Double/Triple Reduction 00B Tapered Bushed Shaft Mount TL TW Key1 V1 Center Distance HT HS LS HY 9.00 YA UY1 U1 Input Shaft XN HB HZ HF O HA D H - 8 Holes EV RU 2F B C MC BB BA A Gear HT A B D 2F H O BA EV HA HB HF HQ HY HZ XM XN YA LS HS TL TW Frame Min. Max M8X M16X M10X M24X M16X M24X M16X M24X Output Shaft Gear Frame BB MC 3 XC Bushing Bore 2 Min. Max /4 1 7/ / / /8 2 7/ / /16 Motor Frame Input Shaft Gear Frame RU U1 UY1 V1 Key /16 Sq /4 Sq /4 Sq /16 Sq Motor Frame Center Distance Center Distance Center Distance Center Distance Min. Max. Min. Max. Min. Max. Min. Max T/145T T/184T T/215T T/256T T/286T Series 1 All rough casting dimensions may vary by up to 0.25" due to casting variations. 2 Refer to Tapered Bushings on pages D-100 and D-101 for a listing of all bushing bore sizes available in each gear frame size. 3 The MC dimension shows spacing required to install or remove the bushing from the gear unit. 4 Bushing and dust cap can be installed opposite of how they are shown above. 5 Driven shaft entry can be from either side of gear housing. Refer to installation manual for requirements. 6 Refer to Mounting Accessories on page D-104 for details of Silent- Bloc and Tie Rod kits. D-161

162 Top Mount Reducer Double/Triple Reduction 00S CEMA Screw Conveyor Drive TL TW Key1 UY1 U1 V1 Input Shaft HT Center Distance HS XN LS HY BB 9.00 AH S T ØP D HZ YA O HF L/2 L D S T AH2 T2 ØJ U Rough End Optional 3 Hole Shaft RU B XC XM Trough End L/2 L A Gear Frame A B D O HF HQ HY HZ XC XM XN YA BB LS HS HT Min. Max. TL TW M16X M24X M24X M24X Series Screw Conveyor Gear Frame 32, Screw Dia. W J L U S T T2 AH AH Input Shaft Gear Frame RU U1 UY1 V1 Key /16 Sq /4 Sq /4 Sq /16 Sq Motor Frame Center Distance Center Distance Center Distance Center Distance Min. Max. Min. Max. Min. Max. Min. Max T/145T T/184T T/215T T/256T T/286T All rough casting dimensions may vary by up to 0.25" due to casting variations. 2 Refer to pages D-102 and D-103 for the screw conveyor drive shafts, trough ends and other accessories available for each frame size. 3 Thrust ratings for each gear frame size are listed on page D-102. D-162

163 Speed Reducer Weights Approximate Shipping Weights - 40C Face Mounted Design C-Face Reducers Frame Reduction Stages 56C 140TC 180TC 210TC 250TC 280TC 320TC , 5, , 5, , 5, Input Shaft Reducers Frame Reduction Stages AP/AD Scoop Top Mount N/A N/A 2 63 N/A N/A N/A N/A 4 73 N/A N/A 5 80 N/A N/A N/A N/A N/A N/A , 5, N/A N/A , 5, N/A N/A RO RO 4, 5, Gear Options - Weight Adders Frame Flange Mount 00B Bushed 00S SCD 31 N/A N/A N/A RO Series D-163

164 Gearmotors and Speed Reducers Lubrication Series gearing is shipped with one of the following synthetic lubricants per the table below and fitted with a magnetic drain. Each reducer is filled according to the mounting position specified when ordered. Refer to unit nameplate and the chart on page D-16 or D-98 for mounting position arrangement for your unit. In the case of synthetic oil, the lubricant does not require changing but it is recommended that proper oil level be checked periodically. Standard Synthetic Gear Oil No Backstop Manufacturer -25 o F to 125 o F (-30 o C to 50 o C) Fuchs Sintogear 125 Mobil Mobilgear SHC 150 Shell Omala Fluids HD 150 With Backstop Manufacturer -25 o F to 125 o F (-30 o C to 50 o C) Shell Omala RL 100 Mobil SHC 629 CAUTION Never mix synthetic oil and mineral oil. Never use extreme pressure (EP) oil in a reducer with a backstop. Refer to installation and maintenance manual for mineral oil selection. Oil Quantity Series Mounting Position * Liters = quarts x.946 Oil Quantity Required in Quarts* Frame Size P P P P PV PV D-164

165 Gearmotors and Speed Reducers Hollow Shaft Details finished bore, hollow shaft gearmotors and speed reducers are supplied with provision for installing and securing the unit on the shaft of the driven equipment. This includes a threaded keeper washer that fits inside the quill between two snap rings that hold the washer axially near the quill end. A pair of snap ring grooves is provided near each end in the quill. This allows the shaft to be installed from either end and secured using the keeper washer in the opposite end. To use this keeper provision, the end of the customer provided driven shaft must be threaded to match the keeper bolt that is supplied with the unit. The bolt thread and length dimensions are shown as dimension M in the table below. The keeper washer may also be used to aid in mounting the gear unit on the driven shaft or for removal of it from the shaft. This is illustrated in the drawings below. A general description of the procedure is also provided. For the complete mounting and dismounting procedure, refer to the product installation manual. Mounting A customer supplied threaded rod and nut (thread size M from the table below), may be inserted through the quill and threaded into the end of the driven shaft. As the nut is tightened, the driven shaft will be pulled into the quill. Refer to the illustration above. After the shaft is pulled up against the driven shaft shoulder, the threaded rod can be replaced with a keeper bolt to secure the gear unit. Removal A customer supplied bolt with threads to match the threaded hole in the keeper washer (see table below) may be threaded into the keeper washer until it contacts the driven shaft end. Tightening the removal bolt will push the gear unit off of the driven shaft. Refer to the illustration above..035 MAXIMUM SHAFT RADIUS L3 L2 L1 RELIEF VG LH M EH THREADED WASHER UY KEY U Driven Shaft Recommendations: It is best to use the keeper bolt to pull the driven shaft into the quill up against a shoulder on the driven shaft. The length of engagement on the driven shaft should be no greater than L1 Max as shown in the table below. The length of engagement should be greater than L2 (see table below) to clear the relief in the quill. Note that these dimensions are shown as though the shaft enters the quill opposite the gear input. Keeper Reducer Shaft Details Driven Shaft Gear Frame Washer M EH LH L2 L3 U 1 UY VG Key L1 Max Thread UNC 31 7/16-14 x /4 Sq /8 3242, /2-13 x /16 Sq /8 3202, /16-14 x /4 Sq /8 33 5/8-11 x 3/ /8 Sq /4 34 5/8-11 x 3/ /2 Sq /4 35 3/4-10 x /8 Sq /8 26 3/ /8 Sq /4 1. Output finished bore tolerances (diameter U ): / for 31 and / for and Keeper bolt is NOT supplied as standard with 26. This bolt must be supplied by customer. Series D-165

166 Complete Gearing Solutions... Standard Solutions Emerson Power Transmission Has the Industry s Broadest Line of Standard Gearmotors and Speed Reducers Cobra Worm Gear Reducer Raider Plus Worm Gear Reducer CbN Inline Concentric Gearmotor Helical Shaft Mount Gearmotor Series PoweRgear Worm Gear Reducer TORQ TAPER Plus Shaft Mount Speed Reducer PSR Helical Parallel Shaft Gear Reducer D-166

167 Gearmotor Typical Motor Performance Data Motor Type MT 4 Pole TEFC - Standard Efficiency 230/460 VAC, 3/60 Motor Efficiency (%) Output Torque Full FL HP Frame Model Load Amps T ypical Guar. FL % of Full Load KVA NEMA Code Design 1/2 3/ 4 4/ 4 4/ 4 Load Load Load L oad Ft. Lbs. Locked Breakdown E K B 48 E B E K B 48 E L B E L B 48 E B T E M C 48 F C T E K C T E L C TY E L B 3 182T E J B 145TY F L B 5 182T E J B T E H B T E H B T E G B T E G C 25 A284T E G C 30 A286T E G C Motor Type MB 4 Pole TEFC - Standard Efficiency - 230/460 VAC, 3/60 Motor Efficiency (%) Output Torque Full FL HP Frame Model Load Amps T ypical Guar. FL % of Full Load KVA NEMA Code Design 1/2 3/ 4 4/ 4 4/ 4 Load Load Load L oad Ft. Lbs. Locked Breakdown T G F B T G F B Motor Type MO 6 Pole TEFC - Standard Efficiency - 230/460 VAC, 3/60 Motor Efficiency (%) Output Torque Full FL HP Frame Model Load Amps T ypical Guar. FL % of Full Load KVA NEMA Code Design 1/2 3/ 4 4/ 4 4/ 4 Load Load Load L oad Ft. Lbs. Locked Breakdown E J B E L B T E K B T E K C T E K C T E L C 3 184T E H B 5 213T E H B T S G B T S F B Meet or exceed NRCan required efficiency. Design C ratings are exempt from this regulation. Note: For 575 VAC motors, use typical data above except current. For 575 V current multiply 460 V value by E-1 Technical

168 Gearmotor Typical Motor Performance Data Motor Type MI (IntelliGear) 4 Pole TEFC - Varidyne Inverter Duty - 115/230 VAC, 3/60 HP Frame Model Full Load FL Motor Efficiency (%) Output Torque rpm Amps T ypical Guar. FL % of Full 60 1/2 Load 3/4 Load 4/4 Load 4 /4 Load Ft. Lbs. Locked Breakdown KVA Code BU R BU N BV N Motor Type MI 4 Pole TEFC - Varidyne Inverter Duty - 230/460 VAC, 3/60 HP Frame Model Full Load FL Motor Efficiency (%) Output Torque rpm Amps T ypical Guar. FL % of Full Load 60 Code 1/2 Load 3/4 Load 4/4 Load 4 /4 Load Ft. Lbs. Locked Breakdown G R G R G M T G N T G L TY G L Motor Type MY, MI 4 Pole TEFC - 230/460 VAC, 3/60 HP Frame Model Motor Efficiency (%) Output Torque Full FL Load Amps T ypical Guar. FL % of Full Load KVA NEMA 1/2 3/ 4 4/ 4 4/ 4 Code Design Load Load Load L oad Ft. Lbs. Locked Breakdown 3 182T G K B 5 184T G J B T G J B T G G B T G G B T G G B T G G B T G G B T G F B T G F B Technical E-2 Motor Type MZ 4 Pole TEFC - Premium Efficiency VAC, 3/60 HP Frame Model Motor Efficiency (%) Output Torque Full FL Load Amps T ypical Guar. FL % of Full Load KVA NEMA 1/2 3/ 4 4/ 4 4/ 4 Code Design Load Load Load L oad Ft. Lbs. Locked Breakdown T AD L B T AD K B 3 182T J K B 5 184T J H B T J H B T J H B T J G B T J G B T G G B T G G B T G F B T G F B Meet or exceed NRCan required efficiency. Design C ratings are exempt from this regulation.

169 Gearmotor Typical Motor Performance Data Motor Type CI 4 Pole TEFC - Corro-Duty - 230/460 VAC, 3/60 HP Frame Model Motor Efficiency (%) Output Torque Full FL Load Amps KVA T ypical Guar. FL % of Full Load Code 1/2 Load 3/4 Load 4/4 Load 4 /4 Load Ft. Lbs. Locked Breakdown BV R BV R BV P T BV N T BV L T BV L 3 182T G K 5 184T G J T G H T G H T G G T G G Motor Type MC 4 Pole TEFC - Corro-Duty - 230/460 VAC, 3/60 Motor Efficiency (%) Motor Type MG 4 Pole - Corro-Duty VAC, 3/60 Meet or exceed NRCan required efficiency. Design C ratings are exempt from this regulation. Output Torque Full FL HP Frame Model Load Amps T ypical Guar. FL % of Full Load KVA Code 1/2 3/ 4 4/ 4 4/ 4 Load Load Load L oad Ft. Lbs. Locked Breakdown G L B G K B G M B T G M B T G K B T G K B 3 182T G K B 5 184T G * J B T G H B T G H B T G G B T G G B T G G B T G G B T G F B T G F B Motor Efficiency (%) Output Torque Full FL HP Frame Model Load Amps T ypical Guar. FL % of Full Load KVA Code 1/2 3/ 4 4/ 4 4/ 4 Load Load Load L oad Ft. Lbs. Locked Breakdown G L B G K B G M B T AD N C T AD L C T AD K C 3 182T G K B 5 184T G H B T G H B T G H B T G G B T G G B NEMA Design NEMA Design E-3 Technical

170 Gearmotor Typical Motor Performance Data Motor Type MS 4 Pole TEFC - Single Phase - 115/230 VAC, 1/60 HP HP Frame Frame Model Model Full Load rpm Motor Type MR 4 Pole TEFC - Single Phase VAC, 1/60 Full Load rpm * FL FL Motor Efficiency (%) Typical Motor Efficiency (%) Typical FL 1/2 Load 3/4 Load 4 /4 Load Ft. Lbs. Output Torque Output Torque Locked % of Full Load Breakdown 3 184T H T H FL 1/2 Load 3/4 Load 4 /4 Load Ft. Lbs. Locked % of Full Load Breakdown E in.-lbs E in.-lbs E E E E E E T E TY E TY E * For dual voltage motors, 115V amps is twice 230V value shown. Technical E-4

171 IntelliGear Plus Variable Speed Gearmotors General Information 1 - General Information General operating principle The IntelliGear Plus is a combination of a 3-phase induction motor and an integrated open loop vector variable speed drive. The motor can be combined with many gear types from Emerson Power Transmission s range. In the standard product version, the integrated drive does not require any connection other than the power supply. The options may be used to broaden the application range of the IntelliGear Plus. Based on the advanced technology of the IGBT power module, very high efficiency and reduced noise levels are achieved Product name 115V Single Phase Supply Power 230V Single Phase Supply IntelliGear Plus Range Power 230V Three Phase Supply Power 460V Three Phase Supply Catalog Number Motor HP Catalog Number Motor HP Catalog Number Motor HP Catalog Number Motor HP 310 M M T T M M T T M M T T M T T M T T M T T T T T T T T Power 7 Designation PD P1 P2 P3 P4 IntelliGear Plus Speed Controlling Options Description Digital keypad on enclosure For./Rev./stop/speed-up/speed-down/speed display Run/Stop/Control knob mounted on enclosure For./Rev./Stop/Control knob mounted on enclosure Control knob (only) mounted on enclosure Control knob (only) mounted inside enclosure w/trim potentiometers R Remore signal following (either 0-10 vdc or 4-20 ma) RP Fieldbus controlled by customer's PROFIBUS DP IntelliGear Plus Options Part ID Description KEYPAD LCD PX KEY AEM904KA006 AEM904KA007 VMA30SOFT Parameter setting console w/cable to locally to customize parameters Drive parameter set-up key storage Fob DC Braking resistors 100W DC Braking resistors 200W CD w/cable and USB to locally to customize parameters E-5 Technical

172 IntelliGear Plus Variable Speed Gearmotors Characteristics Electrical Data Single Phase Design Power supply 115 V ± 10%, Hz 230 V ± 10%, Hz O utput voltage From input voltage down to (input voltage/speed range) Power range 0.33, 0.50, 0.75 HP 0.33, 0.50, , 1.5, 2.0 HP Maximum numbers of power-ups per hour 10 Three Phase Design Power supply 230 V ± 10%, Hz 460 V ± 10%, Hz O utput voltage From input voltage down to (input voltage/speed range) Power range 0.33, 0.50, , 1.5, 2.0, 3, 5 HP 0.33, 0.50, , 1.5, 2.0, 3.0, 5.0, 7.5, 10 HP Maximum numbers of power-ups per hour Characteristics and Functions Characteristic IntelliGear Plus Overload 150 % of full load setting for 60 seconds, 10 times per hour Motor Frequency Variation Ranges 60 to 10 Hz 6:1 constant torque up through 3 HP Standard 74 to 12 Hz 6:1 constant torque for 5 through 10 HP Optional 60 to 6 Hz 10:1 constant torque up through 1.5 HP 90 to 9 Hz 10:1 constant torque for 2 through 10 HP Special 120 to 2 Hz depending on thermal and mechanical limits E fficiency 97.5 % x motor efficiency x gear efficiency (if applicable) Drive Control IntelliGear Plus Speed Reference Analog reference ( 0V or 4mA = minimum speed) (10V or 20mA = maximum speed) - 0 to 10V with integral potentiometer on enclosure ( P1,P2 and P3) - 0 to 10V with integral potentiometer in enclosure (P4) - 4 to ma with external reference - Digital references - Fieldbus using Profibus DP S peed regulation - Speed regulation with encoder feedback option ( only size 33) - Regulation of a reference with integrated PI loop Technical E-6

173 IntelliGear Plus Variable Speed Gearmotors Characteristics and Functions (cont'd.) Drive Control IntelliGear Plus Run/Stop - With power supply - With remote volt-free contact - With fieldbus - With local run/stop control Forward/Reverse - With internal connection on the terminal block - With remote volt-free contact - With fieldbus - With local For./Rev. controls S top Mode - On ramps (using volt-free contact of integrated control) - Freewheel - With electromechanical brake Ramps - Ramps are adjustable from 3 to 600 seconds Fieldbus - PROFIBUS DP Power Control Drive reset Protection IntelliGear Plus - Undervoltage - Overvoltage - Overloads thermal of motor or drive protection from locked rotor - Short-circuit motor windings - Overspeed - Short circuit on 0-10V/24V inputs or outputs - By switching off the IntelliGear Plus or by opening/closing the connection between the 24V and ENA (size 31 and 32) terminals, or SD1 and SDI 2 (size 33) Environmental Characteristics Characteristics Level - IntelliGear Plus Degree of protection TEFC Version TEFC motor and NEMA 4/12 Controller Washdown Version Washdown Motor and NEMA 4/12/Controller Storage temperature -40 oc to +70 oc Transport temperature -40 oc to +70 oc Ambient operating temperature -20 oc to +40 oc (above 40 oc requires derating 1% per oc Altitude Up to feet above sea level without derating Ambient humidity 95% non-condensing Humidity during storage 93%, 40 oc, 4 days Vibration - Exposed product: 0.01 g2 /Hz 1 hr. in accordance with IEC Sinusoidal vibration: 2-9 Hz 3.5 ms Hz 10 ms-2 in accordance with IEC Shocks Packaged product: 15 g, 6 ms, 500 times/direction in all 6 directions in accordance with Standard IEC Immunity Conforming to EN Radiated and conducted emissions Conforming to EN with internal filters U L and cul Standards Conforming to UL 508 C (E211799) * C-Face motors E-7 Technical

174 IntelliGear Plus Variable Speed Gearmotors 2 - Faults - Diagnostics Information relating to the status of the IntelliGear Plus is provided by two indicator lamps located on the control options P1, P2 or P3 or by the internal LED in 31/32. Color and state of indicator lamp Steady green No trip Mains present IntelliGear Plus Checks to be performed Flashing green Flashing red Steady red C urrent limiting Check that the motor is not overloaded or stalled. IGBT temperature alarm Motor overload Braking resistor option overload Check that air is able to circulate around the motor fins and IntelliGear Plus casing. The motor is overloaded: check the motor current using a clamp ammeter. Check that the deceleration ramp is long enough for applications with high inertia. Short-circuit of a motor winding Locked motor rotor Check that no incident has occurred. Faulty insulation of a winding Switch off and then on again to clear the fault. ( I 2T) overheating Check the main voltage. Internal fault Check that the deceleration ramp is long enough for applications with high inertia. Undervoltage If the fault remains, consult Emerson Power Transmission Application Engineering. Overvoltage The fault is cleared by switching off the IntelliGear Plus or by opening/closing the connection between terminals 12: ENA and 11: +24V (31/32) or SDI1 and SDI2 (33). 3 - Operating Extensions Digital Keypad on enclosure with For./Rev./Stop/ Speedup and down/speed display/fault Display A E F G C D Control knob with integrated run/stop control option (P1) In addition to speed control, a run button and a stop button make it possible to control the IntelliGear Plus locally, once it is has been switched on, as required. For a run command to be taken into account, the button must be held down for one second. It is connected on the P2 connector. Has two indicator lights. Technical E-8 Ref. A B C D E F G Function Display comprising 4 x 7 segment - the drive operating status - certain operating data - the adjustment parameters LED providing a sign for the data (the lit LED corresponds to the "-" sign) digits for indicating: (01 to 80) and their value Keys which can be used to scroll up and down through the parameters or their value. These keys can also be used to vary the speed. Keys which can be used to switch from standard mode to parameter-setting mode. In parameter-setting mode, the parameter number and value are displayed alternately on the display. In keypad mode, these buttons are used for the following commands: -Reverse (standerly disabled) - Stop, clear fault - Forward Control knob with forward/reverse/stop control option (P2) In addition to speed control, a forward button, a reverse button and a stop button make it possible to control the IntelliGear Plus locally, once it has been switched on, as required. For a run command to be taken into account, the button must be held down for one second. Connected on the P2 connector Has two indicator lights

175 IntelliGear Plus Variable Speed Gearmotors Speed control knob option (P3) The speed is set using a knob with graduations from 15 to 100 percent. Has two indicator lamps. It is connected on the P2 connector. RF100 = thermal power 100W RF200 = thermal power 200W External resistors with greater thermal power can be used, provided that the minimum ohmic value is maintained Fieldbus options The interface card is fixed inside the casing cover. Protocols: Profibus DP Internal speed control option (P4) The speeds are set on potentiometers, which are accessible once the cover has been removed. - a max. spd potentiometer: calibration of the maximum speed - a min. spd potentiometer: calibration of the minimum speed - an int. spd potentiometer: speed control, which replaces control via the control knob. There are also two indicator lights Parameter-setting console option (Keypad LCD) The console option provides access to the drive Internet settings (terminal block configuration, ramp, speed and P1 settings, etc.). See IntelliGear Plus parameter-setting manual included. Description of the option: 1 Keypad LCD console 1 cable (3m long) Braking resistor option (RF100 - RF200) For operation in four quadrants and energy dissipation, resistors are mounted directly onto the IntelliGear Plus. R F100 RF200 (2x100) P peak P peak kw kw I I31M I Resistor connection erie aralle aralle Minimum ohmic value 2 s s 100Ω 2 p l 50Ω 1 p l 50Ω Programming CD (VMA30SOFT) This CD with manual provides access to the drive internal settings (terminal block configuration, range, speed and PI settings, etc.). Descriptions of the option: 1 CD in case 1 cable (3m long) XPress Key (PX Key) The XPress Key option is used to save a copy of all the IntelliGear Plus parameters so that they can be duplicated very simply in another drive. E-9 Technical