Model 69NT T PL Change 12/96

Transcription

1 Model 9NT40-01 T-7-01PL Change 1/9

2 SERVICE PARTS LIST CONTAINER REFRIGERATION UNIT MODEL 9NT40-01 Carrier Transicold Division, Carrier Corporation, P.O. Box 480, Syracuse, N.Y. 11 Carrier Corporation 199 D Printed in U. S. A. 19

3 TABLE OF CONTENTS Introduction... ii Ordering Instructions... ii Letter Designations... ii Model Chart... iii 1. Quick List --- Clamps, Filter-Drier, Fuse, Ty-Raps, and Wire Terminals Tools Refrigeration Unit Assembly....1 Refrigeration Unit --- Front.... Control Box Door Control Box....4 Control Box --- High and Low Voltage Shields Removed Control Box --- Module Section and Software Cards Condenser Fan Motor and Coil Section Receiver and Tubing Section Water-Cooled Condenser and Tubing Section Fresh Air Makeup and Access Panel Section Evaporator Fan Assembly & Transfresh Option Evaporator Coil Section --- Rear Panels Removed....1 Evaporator Coil Section --- Rear Panels Attached Thermostatic Expansion Valve --- Alco Suction Solenoid Valve --- Alco....1 Modulating Solenoid Valve Recording Thermometer (PARTLOW) Compressor Mounting And Related Components Voltage Options Modular Autotransformer Option Labels and Decals Interrogator and Accessories DataReader Portable/Personal Computer Huskey 1/80 Computer Interrogator Receptacle Compressor --- Motor Assembly Service Replacement Compressor Terminal Mounting and Junction Box Group Service Valve Group Compressor --- Motor Body Group Pump End Group Crankshaft, Rod and Piston Group Valve Plate Group Gasket Set i

4 INTRODUCTION This service parts list identifies service replacement parts for the Carrier Transicold container Models listed in the Model Chart. MODEL AND PRODUCT IDENTIFICATION (PID) NUMBERS Beginning with early 199 production, in addition to a model number, Carrier Transicold is using a parts identification (PID) number in the format of NT0000. In this manual, the PID number is shown in boldface to point out variations within models. Please include the PID number, in addition to the model number, when ordering and inquiring about your unit. ORDERING INSTRUCTIONS All orders and inquiries for parts must include: Parts Identification Number (PID), Model Number, Unit Serial Number, Part Number, Description of part as shown on list and Quantity required. Address all correspondence for parts to the following address: LETTER DESIGNATIONS CARRIER TRANSICOLD DIVISION Replacement Components Group, TR-0 P.O. Box 480, Syracuse, New York 11 or FAX to: (1) The following letter designations are used to classify parts throughout this list: A/R NLO NS NSA NSI NSS P-- PID PL SST SV As Required. No Longer Offered. Not Shown in the illustration. Non-Stock Assembly --- order components listed under the assembly. Non-Stock Item --- may be available on special order. Not Sold Separately --- order next higher assembly or kit. Suffix P-- added to part number means part is available in packaged quantity only. Example: P/N P10 is a package of 10 P/N Use part number and P-- suffix when ordering. Parts Identification Number --- essential to identify unit configuration. Purchase Locally. Stainless Steel Series unless otherwise specified. Suffix SV --- added to part number designates service replacement part. ii

5 MODEL CHART MODEL PID USDA Cold Treatment Transformer Water Cooled Condenser Row Condenser Coil 4 Row Subcooler Suction & Discharge Pressure Gauges Humidity Sensor Transfresh Temperature Recorder (Partlow) Communications Interface Module (CI) 9NT NT000 P P X X --- P NT NT004 P P X X --- P X NT NT000 NT00 P P P P P P X X NT NT001 P X P X P --- X --- 9NT NT0009 P X X X P --- X --- 9NT NT001 NT00 NT007 P P P X X P P P P X X --- 9NT NT00 P X P --- X --- 9NT NT008 P P P X P --- X X P P P P P X X X X X P --- Provision. X --- Features that apply to model. iii

6 PART NO. DESCRIPTION 1. QUICK LIST -- CLAMPS, FILTER-DRIER, FUSE, TY-RAPS, AND WIRE TERMINALS P10 Clamp, Tube, 1/4 --- SST P10 Clamp, Tube, /8 --- SST P10 Clamp, Tube, 1/ --- SST P10 Clamp, Tube, /8 --- SST P10 Clamp, Tube, /4 --- SST P10 Clamp, Tube, 7/8 --- SST P10 Clamp, Tube, 1-1/8 --- SST P10 Clamp, Tube, 1-1/4 --- SST P Connector, Butt End, Wire Range --- to 1 Gauge P Connector, Butt End, Wire Range to 14 Gauge P Connector, Butt End, Wire Range to 10 Gauge P Connector, Closed End, Wire Range --- to 14 Gauge P Connector, Closed End, Wire Range to 10 Gauge U Filter-Drier -0-0P0 Fuse, Amp (F1 & F) -0-0P0 Fuse, 1 Amp (F & F) P Ring Terminal, #, Wire Range to 10 Gauge P Ring Terminal, #10, Wire Range to 10 Gauge P Ring Terminal, /8, Wire Range to 10 Gauge P Ring Terminal, 1/4, Wire Range to 10 Gauge P Ring Terminal, #10, Wire Range to 14 Gauge P Ring Terminal, /1, Wire Range to 14 Gauge P Ring Terminal, #10, Wire Range --- to 1 Gauge P Ring Terminal, /8, Wire Range to 14 Gauge P Spade Terminal, 1/4 x /1, Wire Range to 14 Gauge P Spade Terminal, /8, Wire Range to 10 Gauge F Spiral Wrap, 1/4 Diameter x ft lg F Spiral Wrap, 1/ Diameter x ft lg U1-80-P10 Tube, Heat Shrink, 1/4 ID x -1/8 lg U1-80-1P10 Tube, Heat Shrink, 1/ ID x -/4 lg P Ty-Raps, -1/ inches lg P Ty-Raps, inches lg Series Wire Markers Sealant, Pipe (Used to seal fittings on unit with R-14a) Cleaner, Coil. TOOLS Temperature Tester (Simpson Meter) Temperature Test Lead (1 Foot) Temperature Test Lead (0 Foot) Adapter, Males (Both Ends) (Use with Temperature Tester) Case, Carrying (Used with ) Wrench, Compressor Sight Glass Inspection Light with Mirror Volt-Ohmmeter, Digital Amprobe Clamp (Used with ) Wrench, Service Valve Volt-Ohmmeter, Digital (Fluke) Pliers, Crimping (Used for compressor terminal block replacement) Grip, Wire Vise (Used for compressor terminal block replacement) Test Kit, Total (uses Blue Tube) Package, Total Test (Blue Tube) Kit, Static Dissipative (Used when working on electronic components) Package, Total Test (Gold Tube) SW0 Compressor Oil, Castrol Icematic (Quart) Gauge Set, Manifold --- Fahrenheit/PSI Gauge Set, Manifold --- Centigrade/KPa Detector, Leak Ground Strap, Wrist (Used when working on electronic components) Extractor, Pin (Used on Fan Motor Plugs and Interrogator Plugs) Crimper, Pin (Used on Fan Motor Plugs and Interrogator Plugs) 1

7 . REFRIGERATION UNIT ASSEMBLY.1 REFRIGERATION UNIT -- FRONT

8 ITEM PART NO. DESCRIPTION QTY.1 REFRIGERATION UNIT -- FRONT Fresh Air Makeup & Access Panels --- Refer to Section Labels and Decals --- Refer to Section Evaporator Fan Assembly --- Refer to Section Motor, Condenser Fan --- Refer to Section NT-987 Gutter, Rain --- Optional Box, Control --- Refer to Sections. to NT-811 Handle, Fixed --- Optional Coil, Condenser --- Refer to Section Receiver, Water-Cooled Condenser --- Refer to Section.7 or NT40-7 Handle, Hinged --- Optional Compressor --- Refer to Sections.17 or Guard, Compressor --- Refer to Section Cable, Power --- Refer to Section Plug, Power --- Refer to Section Autotransformer Option --- Refer to Section Transfresh Option --- Refer to Section Connector, Interrogator --- Refer to Section Recording Thermometer --- Refer to Section NT-4047 Panel, Blank NT000,NT004 (NSI) 1 0 9NT-997 Gutter, Rain --- Optional 1

9 . CONTROL BOX DOOR Control Box Control Box Door HINGE ASSEMBLY -- SECTIONAL VIEW DOOR ASSEMBLY -- PARTIAL BACK VIEW 4

10 ITEM PART NO. DESCRIPTION QTY. CONTROL BOX DOOR 1 9NT Door Assembly --- Includes: Gasket, Door SV Window and Gasket Assembly, Control Box Door --- Lexan --- Includes: Nut, Push-on --- SST Washer, Retaining U Screw, Retaining Washer, Mylar, 0.0 ID x OD 8 U Screw, Retaining Hinge Assembly (NSI) --- Includes: NS Hinge, Half 1 NS Hinge, Half 1 NS Pin Assembly, with Tether Protector, Mylar (Hinge) Retainer, Nut Protector, Mylar (Hinge) 1 U Screw, Truss Head, #10-4 x /4 lg --- SST (NSI) 4 14 U1-1- Washer, Lock, # SST 7 1 U1-1-8 Washer, Flat, # SST Washer, Mylar, 0.0 ID x 0.00 OD NT-47 Pocket, Placecard Locknut, Hex Head, # SST (NSI) 19 U Screw, #10-4 x 1/ lg --- SST (NSI) 4 0 U1-1-8 Washer, Flat, # SST 4

11 . CONTROL BOX

12 ITEM PART NO. DESCRIPTION QTY. CONTROL BOX 1 9NT Plate, Schematic & Diagram (NSI) 1 U1-40 Screw, Truss Head, #10-4 x 1/ lg --- SST 9NT4-1 Shield, High Voltage (Plastic) --- Includes: Hinge Rivet, Blind, 1/8 Diameter, Grip Range --- 1/8-/1 --- SST (NSI) Stud & Retainer Package --- Includes: NS NSS Stud, Fastener 1 NS NSS Retainer, Fastener Stud Receptacle Guide, Low Voltage Shield (NSI) 1 9 9NT4-14 Shield, Low Voltage (Lexan) --- With Tether NT-008 Label, Welding Precautions (NSI) NT000, NT NT-17 Label, Welding Precautions (NSI) 1 11 CH Label, High Voltage 1 7

13 .4 CONTROL BOX -- HIGH AND LOW VOLTAGE SHIELDS REMOVED

14 ITEM PART NO. DESCRIPTION QTY.4 CONTROL BOX -- HIGH AND LOW VOLTAGE SHIELDS REMOVED Contactor, Condenser Fan Motor, Heater & Evaporator Fan Motor (EF) 4 U1-91- Screw, Pan Head, (Thread Cutting) #8- x /4 lg --- SST (NSI) A/R 9NT-7 Panel, Contactor (NSI) Spacer (For Contactor Panel) (NSI) Screw, Hex Head, 1/4-0 x 1.00 lg --- SST (NSI) Contact, Auxillary ( N.C.) Plate, Blank (For units w/o CB) (NSI) --- Optional Washer, Lock, # --- SST (NSI) A/R 9 U Screw, Pan Head, #- x 7/1 lg --- SST (NSI) 10 U Circuit Breaker vac (CB1) 1 11 U1-1-7 Washer, Flat, 1/4 --- SST 1 9NT4-1 Bracket, Circuit Breaker (NSI) Receptacle, Retaining (For Control Box Door) Receptacle, Remote Monitoring (RM) (Plastic) --- Optional 1 NS Plug, Remote Monitoring --- Optional Cap and Tether, Receptacle Assembly --- Optional 1 1 U1-8 Gasket, Remote Monitoring Receptacle --- Optional Switch, Toggle (On-Off) 1 18 U1-97 Seal, Bushing A/R Plate, Switch (NSI) NT000, NT001, NT00, NT Plate, Switch (NSI) Switch, Toggle (MDS) Screw, Round Head, #4-40 x /8 lg --- SST (NSI) 4 U1-1- Washer, Flat, 0.1 ID --- SST (NSI) Nut, Self Locking, # SST 4 4 U1--F07 Trim, Flexible (7 ft, Cut to length) A/R 9NT-77 Bracket (NSI) 1 U1-81 Screw, Hex Head, (Thread Cutting) #10-4 x 1/ lg --- SST (NSI) A/R 7 U1-1-8 Washer, Flat, # SST A/R Transformer, Base Unit 1 9 U Screw, Hex Head, #10-4 x 1/ lg --- SST (NSI) A/R Contactor, Compressor (40 Amp) 1 9

15 . CONTROL BOX -- MODULE SECTION

16 ITEM PART NO. DESCRIPTION QTY. CONTROL BOX -- MODULE SECTION Module, Display --- NEW Module, Display --- Remanufactured 1 U Screw, Hex Head, #10-4 x 1/ lg --- SST (NSI) A/R 9NT-9-4 Washer, Fender, 0.0 Thick --- SST (NSI) Module, Controller --- SeeNote1--- Includes: RM Module, Controller --- SeeNote1(Remanufactured) --- Includes: Module, Controller --- SeeNote--- Includes: Module, Controller --- SeeNote(Remanufactured) --- Includes: Module, DataCORDER --- SeeNote--- Includes: Module, DataCORDER --- SeeNote(Remanufactured) --- Includes: Module, DataCORDER --- SeeNote4--- Includes: Module, DataCORDER --- SeeNote4(Remanufactured) --- Includes: 1 U Screw, Hex Head, #10-4 x 1/ lg --- SST (NSI) 1 9NT-9 Washer, Fender, 0.0 Thick --- SST Retainer, Screw, ID (NSI) 1 8 U1-40 Screw, Truss Head, #10-4 x 1/ lg --- SST Washer, Mylar, 0.0 ID x 0.00 OD 10 9NT4-19 Pad, Key --- Includes: Gasket (Between Key Pad Plate Assembly and Connector) (NSI) Gasket (Between Key Pad and Key Pad Plate Assembly) (NSI) 1 1 9NT41-1 Plate Assembly, Key Pad Mounting (NSI) SV Battery Pack --- DataCORDER Module --- Optional Label, DataCORDER Software Programming Port Battery Pack --- Controller Module --- Optional Label, Controller Software Programming Port (NSI) SV Module, Communications Interface (RMU) --- Includes: SV Module, Communications Interface (RMU) --- Includes: 1 19 U1-44- Fastener 4 0 U Retainer Module, High Voltage --- NEW Module, High Voltage --- Remanufactured Card, Controller Configuration Software Card, DataCORDER Configuration Software Fuse, 1 Amp (F) Fuse, Amp (F, F1 & F) NS Card, Controller Operation Software 1 NS Card, DataCORDER Operation Software 1 NS Wire Harness, High Voltage Module to Controller Module 1 NS Wire Harness, Display Module to Controller Module 1 NS Wire Harness, Key Pad to Display Module 1 NS Wire Harness, Controller to DataCORDER 1 NOTE 1: NOTE : NOTE : NOTE 4: The Controller module is configured to ID# 400COA. The Controller module is shipped with the Operation Software pre-loaded, however, it must be programmed with the Configuration Software Card at time of installation. The DataCORDER is configured to ID# X. The DataCORDER module is shipped with the Operation Software pre-loaded, however, it must be programmed with the Configuration Software Card at time of installation. Configuration may be performed through the Interrogator, refer to manual

17 . CONDENSER FAN MOTOR AND COIL SECTION Condenser Fan Grille shown rotated 180 degrees for hinge clarification 1

18 ITEM PART NO. DESCRIPTION QTY. CONDENSER FAN MOTOR AND COIL SECTION 1 9NT Cover, Condenser Coil 1 9NT4-0-SV Coil, Condenser (Copper, 4 row enhanced --- See Model Chart) --- Includes Mylar Washers 1 9NT4--SV Coil, Condenser (Copper, 4 row enhanced w/subcooler) --- Includes Mylar Washers NT See Model Chart 1 9NT4--SV Coil, Condenser (Copper, 4 row enhanced w/subcooler) --- Includes Mylar Washers NT See Model Chart 1 9NT4-0-4SV Coil, Condenser (Copper, row enhanced --- See Model Chart) --- Includes Mylar Washers 1 NS 9NT-870 Protector (Apply between frame and coil & coil cover) 4 U1-1- Capscrew, Hex Head, 1/4-0 x /4 lg --- SST (NSI) 10 4 U1-1-7 Washer, Flat, 1/4 --- SST Washer, Mylar,1/4 ID X /4 OD Washer, Mylar,1/4 ID X 1.00 OD NS Washer, Mylar,1/4 ID X 9/4 OD NS Protector, Mylar (Apply between coil mounting & frame RH side) 1 NS Protector, Mylar (Apply to top side center coil mounting) 1 NS Protector, Mylar (Apply between coil mounting & frame, RH & LH sides) NS Protector, Mylar (Apply to center between frame & coil & coil cover) NS Protector, Mylar (Apply to top side of coil bracket, RH & LH sides) NS Protector, Mylar (Apply under coil center bracket attached to frame) 1 NS Protector, Mylar (Apply between coil & coil cover, RH & LH sides) NS Protector, Mylar (Apply between coil mounting & frame LH side) 1 7 9NT-47 Bracket, Condenser Motor Mount SV Motor, Condenser Fan --- Includes: 1 9 PL Key,/1Squarex1-/8lg---SST 1 NS Bearing NS Capacitor 1 10 U1-1 Screw, Hex Head, /1-18 x 1-1/4 lg --- SST (NSI) Washer, Flat, /1 --- SST (NSI) Washer, Mylar, 1.0 OD x /8 ID Locknut, / SST (NSI) NT-11 Protector, Condenser Fan Motor Mounting 1 9NT4-8 Grille and Venturi Assembly Fan, Condenser (17-1/ diameter) --- Composite --- Includes: 1 17 PL Set Screw,Square Head, /1-4 x /8 lg --- SST Washer, Mylar, 1/4 ID x 9/4 OD 4 19 U Screw, Retaining --- Phillips Head, (NSI) Washer, Retaining --- Nylon Washer, Mylar ID x OD Hinge U1-40 Screw, Truss Head, #10-4 x 1/ lg --- SST 4 4 U1-1- Washer, Lock, # SST 4 U1-1-8 Washer, Flat, # SST Protector, Mylar (Apply between Grille Hinge and Frame) Protector, Mylar (Apply between Grille and Retaining Nut) Nut, Retaining 1

19 .7 RECEIVER AND TUBING SECTION (SRS) 19 (STS)

20 ITEM PART NO. DESCRIPTION QTY.7 RECEIVER AND TUBING SECTION 1 9NT4-40- Receiver, Electro-Coated Modular, Copper --- Includes: Glass, Sight, w/red balls --- 1/ npt Indicator, Moisture-Liquid Plug, Fusible, /8 npt --- Brass Disc, Rupture --- /8 npt (NSI) --- Optional Transducer, Condenser Pressure (CPT) 1 EC9DM0 Valve, Schrader 1 7 U Filter-Drier 1 8 9NT-77 Bracket, Liquid Line Valve (NSI) 1 9 U1-1- Screw, Hex Head, 1/4-0 x /4 lg --- SST (NSI) A/R 10 U1-1-7 Washer, Flat, 1/4 --- SST Washer, Mylar, 0.0 ID x OD Coupling, M1 --- Brass --- Includes: Cap, Service Port Valve, Liquid Line 1 1 U1-1-7 Bolt, Hex Head, /8-1 x 1.00 lg --- SST (NSI) 1 1 AU11JR41 Washer, Lock, /8 --- SST 1 17 U1-1- Washer, Flat, /8 --- SST (NSI) Washer, Mylar, 0.7 ID x 1.00 OD SV Sensor Assembly (STS & SRS) Valve, Pressure Regulator Receptacle, 4 Pin (SSV/SMV) Lock, Secondary, 4 Pin (SSV/SMV) Contact, Pin #1 (SSV/SMV) Plug, 4 Pin (SSV/SMV) Lock, Secondary, 4 Pin (SSV/SMV) Contact, Socket #1 (SSV/SMV) Valve, Modulating Solenoid --- Refer to Section Sensor, Ambient Thermistor (AMBS) Valve, Suction Solenoid --- Refer to Section Valve, Quench, Thermostatic Expansion 1 1 U1-- Clamp, Tube, 1/ inch Diameter Cushion 1 U1-71- Screw, Hex Head, Slotted, #10-4 x /4 lg --- SST (NSI) Washer, Mylar, 0.0 ID x 0.00 OD Protector, Mylar (NSI) 1 1

21 1.8 WATER-COOLED CONDENSER AND TUBING SECTION (STS) (SRS)

22 ITEM PART NO. DESCRIPTION QTY.8 WATER-COOLED CONDENSER AND TUBING SECTION --- 9NT4-914 Kit, Condenser/Receiver (For Field Installation --- See NOTE) --- Includes: 1 1 9NT Condenser/Receiver (See Model Chart) --- Includes: Sight Glass, w/red balls, 1/ npt Protector, Mylar Protector, Mylar 1 U1-7- Coupling (Water-In) 1 U-114 Cap, Dust Coupling, Self Draining --- Includes: Seal, O-Ring 1 9 U-11 Cap, Dust SV Switch, Water Pressure Disc, Rupture, /8 npt 1 1 U1-1-7 Bolt, Hex Head, /8-1 x 1.00 lg --- SST (NSI) 1 1 U1-1- Washer, Flat, /8 --- SST (NSI) 1 14 AU11JR41 Washer, Lock, /8 --- SST Washer, Mylar, /8 ID x 1.00 OD 1 1 U1-1- Capscrew, Hex Head, 1/4-0 x /4 lg --- SST (NSI) 17 U1-1-7 Washer, Flat, 1/4 --- SST Washer, Mylar, 1/4 ID x 1/1 OD SV Sensor Assembly (STS & SRS) Valve, Pressure Regulator Receptacle, 4 Pin (SSV/SMV) Lock, Secondary, 4 Pin (SSV/SMV) Contact, Pin #1 (SSV/SMV) Plug, 4 Pin (SSV/SMV) Lock, Secondary, 4 Pin (SSV/SMV) Contact, Socket #1 (SSV/SMV) Valve, Modulating Solenoid --- Refer to Section Sensor, Ambient Thermistor (AMBS) Valve, Suction Solenoid --- Refer to Section Valve, Quench, Thermostatic Expansion Accessory Kit, Water-Cooled Condenser Tubing --- Includes: DA Valve, Schrader Transducer, Condenser Pressure (CPT) 1 9NT Tube Assembly (NSI) --- Includes: 1 4 DE41CA0 Tee, 1/ x 1/ x /8 npt --- Brass 1 U Filter-Drier 1 9NP0-101 Clamp, Filter-Drier --- Includes: 1 NS F1 Gasket (1 ft., Cut to length) 1 7 9NT Tube Assembly (NSI) --- Includes: 1 8 U1-8- Valve, Liquid Line --- Includes: Cap, Flare --- 1/ Cap, Valve Coupling, M1 --- Brass --- Includes: Cap, Service Port 1 4 9NT-87 Bracket (NSI) 1 44 U Screw, Hex Head, #10-4 x /4 lg --- SST Washer, Mylar, 0.0 ID x 0.00 OD 4 9NT Tube Assembly (NSI) --- Includes: Indicator, Liquid Moisture --- Brass 1 NOTE: Must order condenser tubing accessory kit P/N when ordering P/N 9NT4-914 for field installation on units provisioned for a water-cooled condenser. 17

23 .9 FRESH AIR MAKEUP AND ACCESS PANEL SECTION

24 ITEM PART NO. DESCRIPTION QTY.9 FRESH AIR MAKEUP AND ACCESS PANEL SECTION 1 9NT41-91 Panel, Access w/retaining Washers NT000,NT000,NT Includes: 1 1 9NT Panel, Access --- Includes: Gasket Gasket, x 0.0 Halfmoon Capscrew, Hex Head, 1/4-0 x 1 lg --- SST (NSI) Washer, Flat, 1/4 --- SST Washer, Mylar,1/4 ID X 0.80 OD 4 7 9NT Panel, Access w/retaining washers NT000,NT000,NT Includes: 1 7 9NT Panel, Access --- Includes: Gasket 1 9 U1-811-F0 Gasket, Access Panel, Seal --- Adhesive back, Pressure sensitive, 4.0x1/thick(0ft,Cuttolength) Screw, Hex Head, 1/4-0 x 1.00 lg --- TIR 11 9NT Panel w/retaining Washers and Medfly screen, Fresh Air Makeup NT000,NT000,NT Includes: NT Panel, Fresh Air Makeup --- Includes: Gasket Gasket, x 0.0 Halfmoon 1 1 9NT Disc Assembly --- Includes: Gasket (NSI) Gasket (NSI) 1 CH Label, Arrow (NSI) Washer, Mylar, 1.00 OD x 0. ID NT-9-1 Washer, Fender, 1/4 (NSI) 1 18 U1--1 Nut, Wing, 1/ Label, Fresh Air --- English Label, Fresh Air --- English/Spanish NT000, NT U1--18 Gasket, 0.7 x 1. x 1. (NSI) 19

25 .10 EVAPORATOR FAN ASSEMBLY AND TRANSFRESH OPTION EFM- (Location) EFM-1 (Location) Partial view of the lower left corner of the unit. 0

26 ITEM PART NO. DESCRIPTION QTY.10 EVAPORATOR FAN ASSEMBLY AND TRANSFRESH OPTION 1 9NT4-9 Mounting Bracket, Evaporator Fan Assembly 4 9NT-9-1 Washer, Fender (NSI) Washer, Lock, 1/4 --- SST (NSI) Screw, Hex Head --- 1/4-0 x 1. lg --- SST (NSI) Nut, Self Locking, / SST (NSI) U1-1-9 Washer, Flat, /8 --- SST (NSI) Fan, Evaporator Stator, Evaporator Protector --- Mylar Motor, Evaporator Fan Washer, Flat, 1/4 --- SST (NSI) Screw, Hex Head, 1/4-0 x /4 lg --- SST (NSI) Kit, Transfresh Field Installation (For units with NO Transfresh Provision) --- Includes: Screw, Hex Head, 1/4-0 x -1/ lg --- SST (NSI) NT-48 Bracket NS Pipe Assembly, PVC (NSI) 1 1 9NT Cable Assembly, Transfresh Communications Connector (TCC) (NSI) 1 NS 9NT Cable Assembly, Rear (Transfresh) (NSI) 1 NS 9NT Cable, Power --- AC (Transfresh) (NSI) 1 NS 9NT-874- Hose Assembly, Air (Transfresh) (NSI) 1 NS 9NT-874- Fuse Assembly, In-line (Transfresh) (NSI) 1 1

27 .11 EVAPORATOR COIL SECTION -- REAR PANELS REMOVED (RRS) 1 (RTS) Side or Rear Mount USDA option.

28 ITEM PART NO. DESCRIPTION QTY.11 EVAPORATOR COIL SECTION -- REAR PANELS REMOVED SV Sensor Assembly (RRS & RTS) --- Sensor, Thermistor, (Recording Thermometer) --- Refer to Section Sensor, Thermistor, Defrost (DTS) Screw, Hex Head, #8- x 1/ lg --- SST (For mounting DTS) (NSI) U Thermostat, Heat Termination (HTT) 1 PL Capscrew, Hex Head, 1/4-0 x 1/ lg 1 7 PL Washer, Lock, 1/4 --- SST NT4-08- Coil, Evaporator (Does not include thermostats or heaters) 1 NS 9NT- Retainer (For Heaters) NS 9NT- Clip (For Heaters) 4 9 PL Capscrew, Hex Head, 1/4-0 x /4 lg --- SST 9 10 PL Washer, Flat, 1/4 A/R 11 PL Screw, Lag, 1/4 x lg Valve, Thermostatic Expansion --- (Location) Refer to Section Heater, Drain Pan Receptacle, Interrogator (ICR) (NSI) 1 1 9NT4-17 Cap, Dust, with Tether ( Pin Receptacle) Contact, Pin #1 (Used with & ) Plug, Sealing 4 NS Plug, Socket (ICR) --- Optional NT4-17 Cap, Dust, with Tether ( Pin Receptacle) Receptacle --- Pin (PR1, PR, PR, Cargo Probe 4) (NSI) Cap and Chain (Used with P/N ) Receptacle, Interrogator --- Pin 1 * Socket, Contact (Silver Plated) * Socket, Contact (Gold Plated) NS Sensor Assembly (USDA) --- Optional --- Includes: 4 NS Plug, Socket (PR1, PR, PR, Cargo Probe 4) --- Optional 1 NS Contact, Socket #1 (Used with & ) Exchanger, Heat Heater, Evaporator Coil 4 NS U Tube, Heat Shrink, 1/ x -/4 lg A/R Plug, Hole ( inch diameter) (Located on Fan Deck) Sensor, Humidity (HS) (See Model Chart) 1 7 U Screw, Hex Head, #10-4 x 1.00 lg --- SST --- Optional (NSI) 4 8 U1-1-8 Washer, Flat, # SST 9 9NT41-18 Bracket Assembly, Humidity Sensor --- Optional 1 * NOTE: Do not mix silver pins with gold pins and sockets.

29 ITEM PART NO. DESCRIPTION QTY.1 EVAPORATOR COIL SECTION -- REAR PANELS ATTACHED UNITS WITH BOLTED PANELS 1 9NT4-4 Grille, Top Rivet, Blind, /1 Diameter, Grip Range --- 1/8-1/4 (NSI) 17 U Rivet, TIR, /1 Diameter, Grip Range --- /4-11/4 (NSI) 4 4 9NT41-94 Panel Assembly, Upper --- Includes: 1 NS NSS Drain Pan, Side (Location --- Behind upper panel) NS NSS Drain Pan, Center (Location --- Behind upper panel) Gasket (Location --- Behind upper panel) Rivet, Blind, 1/4 Diameter, Grip Range --- 1/8-/1 (NSI) Rivet, Blind, 1/4 Diameter, Grip Range --- /1-1/4 (NSI) 8 9NT-78 Panel, Bottom 1 9 9NT-78-1 Panel, Bottom (Provision for heat exchanger location) 1 10 U1-40 Screw, Machine, Truss Head, #10-4 x 1/ lg --- SST NT-9 Washer, Fender, #10 x 1.00 OD --- SST 18 NS U1-807-F Gasket ( ft, Cut to length) A/R 4

30 ITEM PART NO. DESCRIPTION QTY.1 THERMOSTATIC EXPANSION VALVE -- Alco 1 7 Alco Part Nos. A-A A-4A A-A A-A A-7A 4 A-4A Kit, Repair --- Includes: 1 NSS PowerHeadAssemblyandGasket,Item 1 NSS Cage Assembly and Gasket, Item 1 4 U1- Gasket Set, Universal --- Includes: 1 NSS Gasket, Body Flange A-4A NSS Gasket, Seat --- A-A 1 7 U Flange, Body (NSI) 1

31 ITEM PART NO. DESCRIPTION QTY.14 SUCTION SOLENOID VALVE -- Alco Solenoid Valve, Suction --- Includes: Cap, Snap Coil Kit, Repair Kit, Repair Diaphragm 1

32 ITEM PART NO. DESCRIPTION QTY.1 MODULATING SOLENOID VALVE * Kit, Enclosing Tube & Coil Housing --- Includes: Nut, Coil --- Includes: 1 NSS Nut, Coil 1 4 NSS O-Ring, Coil Nut Housing, Coil --- Includes: 1 NSS Housing, Coil 1 * 7 NSS Plate, Coil Bottom 1 8 NSS O-Ring, Coil Bottom Plate 1 9 NSS Sleeve, Solenoid Coil 1 10 NSS Tube Assembly, Coil Plate & Enclosing Valve, Modulating Solenoid --- Includes: Coil, Solenoid --- Includes: 1 9 NSS Sleeve, Solenoid Coil Core, Valve (Schrader Valve) Cap, Service 1 * NOTE: Coil bottom plate is only supplied in Kit as a separate item for use on early style enclosing tube assemblies. 7

33 .1 RECORDING THERMOMETER (PARTLOW)

34 ITEM PART NO. DESCRIPTION QTY.1 RECORDING THERMOMETER (PARTLOW) Recording Thermometer (See Model Chart)--- Includes: Cover Assembly (Bottom Latch) --- Includes: 1 NS Seal, Cover --- Rubber SV Glass, Cover w/gasket --- includes 1 NS Gasket, Cover Glass 1 NS Catch Assembly, Cover Kit, Stylus --- Includes: 1 4 NSS Screw, Round Head, #- x /1 lg Mechanism and Platen Assembly Main Lever and Push Rod Assembly (Includes Setscrews) Rod, Push Key, Clock Winding Nut and Chain, Chart (Sonceboz Clock) Nut and Chain, Chart (Gluck Clock) 1 10 PL Screw, Round Head #- x / Flange, Chart Drive (Sonceboz) Flange, Chart Drive (Gluck) Clock, 1 Day, CCW (Counterclockwise) Case (Top Hinge) (Use with P/N ) Case (Top Hinge) (Use with P/N ) O-Ring, Element Flange Element, 9 ft lg (Use with P/N ) --- Includes: Element, 9 ft lg (Use with P/N ) --- Includes: 1 NS Sensor, Thermistor (Accessory 44 and Jack) ft lg 1 NS -04 Pin (Use with Partlow Thermistor Assembly) Screw, Flange (NSI) NS Charts _F Day (Box of 0) (---0_F to+80_f) A/R NS Charts _C Day (Box of 0) (---_C to+_c) A/R NS Kit, Hold Open Latch --- Includes Hardware 1 NS Kit, Hinge Replacement --- Includes Hardware 1 9

35 .17 COMPRESSOR MOUNTING AND RELATED COMPONENTS Center Cylinder Head View with gauges Compressor Foot -- Cutaway View Center Cylinder Head View without gauges Unit -- Sectional View 0

36 ITEM PART NO. DESCRIPTION QTY.17 COMPRESSOR MOUNTING AND RELATED COMPONENTS Compressor --- Refer to Section --- 9NT40-94 Stiffener Assembly 1 NS U1-1-8 Washer, Flat, # SST Used to mount NS U1-71- Screw, Hex Head, #10-4 x /4 lg --- SST (NSI) Stiffener Assembly NS Washer, Mylar, 0.0 ID x 0.00 OD 9NT40-91 Bracket Assembly, Gauge Gauge, Suction Pressure (See Model Chart) Gauge, Discharge Pressure (See Model Chart) 1 U Screw, Pan Head, #- x 7/1 lg --- SST (NSI) 7 CA1JA01 Tee, 1/4 npt (NSI) Elbow, 90 Street, 1/4 mpt x 1/4 mpt --- Brass 1 9 0DA Valve Assembly, Core, Check (Schrader Valve) --- Brass Snubber Assembly Switch, High Pressure (HPS) 1 NS Connector, Male, Pin (Used with HPS) (NSI) 1 NS Seal, Cable (Used with HPS) (NSI) 1 1 9NT41- Tube Assembly, Low Pressure 1 1 9NT41-4 Tube Assembly, High Pressure Plug, Pipe, 1/4-18 nptf --- Brass 1 1 9NT-1 Protector (Compressor to Compressor Base) 1 1 AU11JR41 Washer, Lock, /8 --- SST 17 AA0JA Capscrew, Hex Head, /8-1 x 1-1/4 lg --- SST (NSI) Washer, Flat, /8 --- SST (NSI) Washer, Mylar, 0.7 ID x 1.00 OD 0 9NT4-108 Base, Compressor 1 NS U1-1-7 Bolt, Hex Head, /8-1 x 1.00 lg --- SST (NSI) 7 NS U1-1- Washer, Flat, /8 --- SST (NSI) Used to mount 7 NS AU11JR41 Washer, Lock, /8 --- SST Compressor Base 7 NS Washer, Mylar, 0.7 ID x 1.00 OD to unit frame Capscrew, 7/1-14 x -/4 lg --- SST (NSI) Locknut, 7/ SST (NSI) U1-1-8 Washer, Flat, 7/1 --- SST Washer, Mylar, 0.48 ID x 0.9 OD (NSI) Washer, Mylar, 0.48 ID x 1.1 OD 9NT-7-1 Panel, Guard (NSI) 1 7 U1-1- Screw, Hex Head, 1/4-0 x /4 lg --- SST (NSI) 1 8 U1-1-7 Washer, Flat, 1/4 --- SST Washer, Mylar, 1/4 ID x /4 OD 9 0 U Capscrew, Hex Head, 1/4-0 x 1-1/ lg --- SST (NSI) Locknut, 1/ SST (NSI) 4 9NT Guard, Compressor 1 NS Oil, Compressor (Quart) A/R 1

37 .18 VOLTAGE OPTIONS POWER CABLE DOOR

38 ITEM PART NO. DESCRIPTION QTY.18 VOLTAGE OPTIONS Clamp, Tube, Cushion, 9/1 Diameter --- SST (Used w/transicord) NSI A/R Clamp, Tube, Cushion, /4 Diameter --- SST A/R U Screw, Hex Head, #10-4 x /4 lg --- SST A/R Washer, Mylar, 0. ID x 1.00 OD A/R Cable, Power --- Yellow, amp, 11 gauge, Transicord (40 vac) (NSI) A/R 4 U1-978 Cable, Power --- Yellow, amps, 10 gauge (40 vac) (NSI) A/R Plug, Power --- Mennekes (40 vac) 1 U1-1-1 Plug, Power --- Mipco (40 vac) 1 NS Bushing (For P/N & U1-1-1) (NSI) 4-0 Plug, Power (40 vac) 1 NS Bushing (For P/N -0) (NSI) 4 9NT-41 Clamp, Cable (NSI) Protector, Mylar 1 8 U Screw, Hex Head, 1/4-0 x 1-1/ lg --- SST (NSI) Locknut, Hex Head, 1/ SST (NSI) 10 U Cable, Power --- Black (0 vac) (NSI) A/R Plug, Power --- Mipco (0 vac) 1 NS Bushing (For P/N -0-00) (NSI) 4 1 9NT Cover Assembly w/latch, Cable Storage (Optional) --- Includes: Screw, Hex Head, #4-40 x 1/ lg --- SST Washer, Flat, #4 --- SST Locknut, Hex Head, # Washer, Mylar, 1/8 ID x /8 OD (NSI) Latch NT-80 Hinge 19 U1-40 Screw, Truss Head, #10-4 x 1/ lg --- SST 4 0 U1-1-8 Washer, Flat, # Locknut, Hex Head, # SST (NSI) Washer, Mylar, /1 ID x /8 OD Protector, Mylar (NSI) Protector, Mylar Washer, Mylar, /1 ID x /8 OD Retainer, Nut 1 7 U1-40 Screw, Truss Head, #10-4 x 1/ lg --- SST 8 U1-1-8 Washer, Flat, # SST 9 U1-1- Washer, Lock, # SST (NSI) Latch, Catch 1

39 .19 MODULAR AUTOTRANSFORMER OPTION

40 ITEM PART NO. DESCRIPTION QTY.19 MODULAR AUTOTRANSFORMER OPTION Transformer Kit, Field Installation --- Includes: U1-0 Strap, Tie Down 1 9NT-41- Clamp, Cable Cutter (NSI) Protector, Mylar 1 4 U Screw, Machined Hex Head, 1/4-0 x 1-1/ lg --- SST (NSI) U1-1-7 Washer, Flat, 1/4 --- SST A/R Locknut, Hex Head, 1/ SST (NSI) 7 9NT-99 Clamp, Tie Down Strap (NSI) Rivnut, 1/ SST (NSI) 9 U1-1- Bolt, Hex Head, 1/4-0 x /4 lg --- SST (NSI) A/R Washer, Mylar, 0. ID x 1.00 OD Transformer, Dual Voltage Modular (See Model Chart) Circuit Breaker, 0 amp vac, 0/0 hz 1 1 U-11 Boot --- Includes: 1 NS NSS Frame 1 NS NSS Screw, #- x /8 lg --- Self Sealing 14 U Screw, Hex Head, #10-4 x 1/ lg --- SST (NSI) 4 1 U1-1-8 Washer, Flat, # SST Washer, Mylar, 0.0 ID x 0.00 OD Receptacle, Mennekes amp NT4-74 Bracket Assembly (NSI) Protector, Mylar (NSI) Washer, Mylar, 0.0 ID x OD 1 AU11JR171 Washer, Lock, 1/4 --- SST AA0JA170 Screw, Hex Head, 1/4-0 x 1.00 lg

41 .0 LABELS AND DECALS

42 ITEM PART NO. DESCRIPTION QTY.0 LABELS AND DECALS Decal, Carrier Transicold Thinline Decal, Carrier (NSI) NT000, NT004 1 U1-891 Label, Rotation Arrow Label, Function Code (NSI) Label, Operating Instructions (NSI) Label, Operating Instructions (NSI) NT000, NT Label, Micro-Link (NSI) Label, Charge with R-14a (NSI) Label, R-14a --- Ozone Protection (NSI) Label, POE Compressor Oil Refer to Section.9 for Fresh Air Makeup labels

43 4. INTERROGATOR AND ACCESSORIES 4.1 DATAREADER DataReader 1 9volt 4 DataReader 10 Personal Computer OPERATING INSTRUCTIONS DATA RETREIVAL FOR MICRO-LINK AND MICRO-LINK 8

44 ITEM PART NO. DESCRIPTION QTY 4.1 DATAREADER Kit, DataReader --- Includes: DataReader (NSI) Cable, Download Cable, Adapter (NSI) Cable, Upload (NSI) 1 PL Battery, Akaline Volt Software, DataView (DOS) (. DS/HD Diskette, Formatted) Manual, Operating Instructions Kit, Battery, with Cable --- Includes: Battery, External, with Battery Charger Cable Kit, Cable, with Adapter --- Includes: Cable, Interrogator Adapter 1 NOTE: If a DS/DD Diskette is required, contact a Customer Service Representative. 9

45 4. PORTABLE/PERSONAL COMPUTERS 10 9 NO TAG 8 7 Portable/Personal Computer 11 NO TAG Husky 1/80 Computer 1 4 Portable/Personal Computer Printer Portable/Personal Computer PARALLEL PRINTING Purchase cable locally Purchase cable locally 1 1 Printer Portable/Personal Computer SERIAL TO PARALLEL PRINTING 11 Printer Portable/Personal Computer SERIAL PRINTING PORTABLE/PERSONAL COMPUTER CONNECTIONS 40

46 ITEM PART NO. DESCRIPTION QTY 4. PORTABLE/PERSONAL COMPUTERS --- NLO Interrogator Kit, Field (Optional) --- Includes: NSS Computer, Husky 1/80 (NSI) --- Includes: Manual, Husky 1/80 Operator (NSI) 1 PL Batteries, AA Alkaline Case (for Husky 1/80) (NSI) Software, PC/DOS (. DS/HD Diskette) SeeNotebelow Cable Assembly --- Micro-Link and Micro-Link --- Includes: Cable Assembly, Adaptor (Micro-Link cable to Micro-Link cable) 1 8 NSS Cable Assembly (Micro-Link cable to computer) NLO Interrogator Kit, Desktop (Optional) --- Includes: --- NS NLO Disk Drive,. DS/HD for Husky 1/80 (NSI) Software, PC/DOS (. DS/HD Diskette) SeeNotebelow Battery Charger --- AA NiCad Battery Pack, Rechargeable --- AA NiCad (4 Pack) (NSI) Adapter, DBM to DB9F ( pin male to 9 pin female) Cable Assembly (Husky to computer or printer) NS Microbuffer Package, Mini (for Husky to parallel Printer) --- Includes: 1 1 NSS Microbuffer, Mini 1 14 NSS Cable, Peripheral 1 NOTE: If a DS/DD Diskette is required, contact a Customer Service Representative. 41

47 4. HUSKEY 1/80 COMPUTER Husky 1/80 Computer 11 Printer SERIAL PRINTING Husky 1/80 Computer 1 1 Printer Purchase cable locally SERIAL TO PARALLEL PRINTING HUSKY 1/80 COMPUTER CONNECTIONS 4

48 ITEM PART NO. DESCRIPTION QTY 4. HUSKEY 1/80 COMPUTER --- NLO Interrogator Kit, Field (Optional) --- Includes: NSS Computer, Husky 1/80 (NSI) --- Includes: Manual, Husky 1/80 Operator (NSI) 1 PL Batteries, AA Alkaline Case (for Husky 1/80) (NSI) Software, PC/DOS (. DS/HD Diskette) SeeNotebelow Cable Assembly --- Micro-Link and Micro-Link --- Includes: Cable Assembly, Adaptor (Micro-Link cable to Micro-Link cable) 1 8 NSS Cable Assembly (Micro-Link cable to computer) NLO Interrogator Kit, Desktop (Optional) --- Includes: --- NS NLO Disk Drive,. DS/HD for Husky 1/80 (NSI) Software, PC/DOS (. DS/HD Diskette) SeeNotebelow Battery Charger --- AA NiCad Battery Pack, Rechargeable --- AA NiCad (4 Pack) (NSI) NS Adapter, DBM to DB9F (Not used on Huskey 1/80) Cable Assembly (Husky to computer or printer) NS Microbuffer Package, Mini (for Husky to parallel Printer) --- Includes: 1 1 NSS Microbuffer, Mini 1 1 NSS Cable, Peripheral 1 NOTE: If a DS/DD Diskette is required, contact a Customer Service Representative. 4

49 4.4 INTERROGATOR RECEPTACLE

50 ITEM PART NO. DESCRIPTION QTY 4.4 INTERROGATOR RECEPTACLE 1 9NT4-17 Cap, Dust, with Tether, Interrogator --- Pin (Optional) Receptacle, Interrogator (Optional) (NSI) Contact, Pin Socket Plug, Interrogator (Optional) Contact, Socket 9NT41-19 Bracket, Interrogator Connector (Optional) 1 7 9NT40-7- Connector, Interrogator --- Includes: 1 NS Receptacle 1 NS Pin, Contact NS Plug 1 NS Contact 1 NS Contact 4

51 . COMPRESSOR -- MOTOR ASSEMBLY Existing parts on compressor terminal block O-ring Bushing Terminal block Terminal post Wire assembly 1/ Inch diameter heat shrink tubing Compressor junction block 1/4 Inch diameter heat shrink tubing 4

52 ITEM PART NO. DESCRIPTION QTY.1 SERVICE REPLACEMENT COMPRESSOR SV Compressor, 41 CFM, 40 vac/ ph/0 hz 1 NOTE The Service Replacement Motor --- Compressor is sold without terminal box and cover, and without shut-off valves (but with valve pads). Customer should retain the original terminal box and valves for use on replacement compressor.. TERMINAL MOUNTING AND JUNCTION BOX GROUP 9NT0-08 Cover, Junction Box 1 U Screw, Hex Head, #10-4 x 1/ lg (cover to box) --- SST (NSI) 4 U1-1-8 Washer, Flat, #10 (cover to box) --- SST 9NT0-1-1SV Box, Junction (Located on Front of Compressor) --- Includes: 1 9NT0-1-SV Box, Junction (Located on Back of 0/40v Compressor) --- Includes: 1 9NT0-08 Cover, Junction Box 1 PL Screw,PanHead,#10-x/8lg(boxtocompressor) Terminal, Compressor ( Terminals) Terminal, Compressor ( Terminals) Kit, Compressor Terminal Wiring (Single Voltage) 1 NS Kit, Compressor Terminal Wiring (Dual Voltage or Single Voltage) 1 NS Gasket, Terminal Plate Washer, Mylar, 0.0 ID x 0.00 OD. SERVICE VALVE GROUP Elbow, M1 x M1 --- Brass Coupling, M1 --- Brass --- Includes: Cap, Service Port Valve, Suction Shut-Off, 1-1/8 ODS Cap, Seal 1 NS Gasket, Seal Cap Gasket, Suction Service Valve Valve, Discharge Shut-Off, 7/8 ODS Cap, Seal 1 NS Gasket, Seal Cap Gasket, Discharge Service Valve 1 19 U1-1-4 Bolt, Hex Head, /1-18 x 1-7/8 lg --- SST (NSI) Gasket, Bolt, / Elbow, M1 x M1 --- Brass Coupling, M1 --- Brass --- Includes: Cap, Service Port 1.4 COMPRESSOR -- MOTOR BODY GROUP NS --- Gasket Set (Refer to Section.8) Head, Cylinder --- Side Bank (Shaved Head) Head, Cylinder --- Center Bank Screw, Hex Head --- Center Head, /8-1 x.00 lg --- SAE Grade Gasket, Cylinder Head (Side Bank) Screw, Hex Head, /8-1 x.00 lg --- SAE Grade Screw, Hex Head, /8-1 x 1.00 lg --- SAE Grade Screen Assembly, Oil Filter 1 47

53 ITEM PART NO. DESCRIPTION QTY.4 COMPRESSOR -- MOTOR BODY GROUP (CONTINUED) Tube, Oil Suction Orifice, Oil Relief Sight Glass Package, Oil Level --- Includes: Gasket, Sight Glass Cover, Motor End (NSI) Gasket, Motor End Cover 1 7 PL Screw, Hex Head, 7/1-14 x 1-1/4 lg --- SAE Grade Plate, Bottom Gasket, Bottom Plate Screw, Hex Head, /8-1 x.00 lg --- SAE Grade Strainer Assembly, Suction (NSI) 1 4 PL Plug, Pipe, Oil Fill, 1/ Check Valve Assembly, Oil Return Plate, Screen Hold Down 1 4 PL Pipe Plug (High & Low Pressure Connection and Oil Drain), 1/4-18 NPT Gasket, Cylinder Head (Center Bank) 1. PUMP END GROUP Screw, Hex Head, Bearing Head, /8-1 x 1.00 lg --- SAE Grade Gasket, Capscrew, / Gasket, Cover Plate Bearing Head & Low Profile Oil Pump Package 1. CRANKSHAFT, ROD AND PISTON GROUP 1 N/A Crankshaft Washer, Thrust Pin, Spiral, / Diameter x /8 lg Key, Rotor Drive Washer, Rotor (NSI) Washer, Star, Rotor, /8 (NSI) Tube Assembly, Equalizer (NSI) Piston & Pin Pkg (Standard) --- Includes: Piston & Pin Pkg (+0.00) --- Includes: A/R 9 NSS Piston Pin, Piston Retainer, Piston Pin Ring, Compression (Standard) Ring, Compression (+0.00 inch Piston) Connecting Rod and Cap Assembly (Standard) --- Includes: 17-0 Connecting Rod and Cap Assembly (+0.010) --- Includes: NS Pin, Dowel Capscrew --- Special (Epoxy Coated).7 VALVE PLATE GROUP Package, Valve Plate Assembly (Center and Side Banks -- Canted) --- Includes: NS NSS Plate Assembly, Valve --- Includes: 1 NSS Plate, Valve Valve, Discharge Valve, Stop Discharge Screw, Hex Head, 1/4-8 x /8 lg Washer, Lock, 1/ Valve, Suction Spring, Suction Valve Positioning Gasket, Cylinder Head (Side Bank) Gasket, Cylinder Head (Center Bank) Gasket, Valve Plate Pin, Dowel (Valve Plate) 1 Revised 1//9 48

54 ITEM PART NO. DESCRIPTION QTY.8 GASKET SET * Gasket Set --- Includes: Gasket, Suction Service Valve (4 Bolt) Gasket, Seal Cover Plate (0G) --- Fiber Gasket, Seal Cover Plate (0G) --- Coated Steel Gasket, Valve Plate (0G) Gasket, End Flange (0G) --- Includes: Gasket, Flange Spacer (0G) Gasket, Cylinder Head --- Side Bank (Standard) Gasket, Valve Plate Gasket, Cylinder Head --- Center Bank Gasket, Cylinder Head --- Side Bank (Hot Gas Bypass Unloader) Gasket, Oil Supply Tube (O-Ring, 0D) Gasket, Sight Glass Gasket, Unloader Body Gasket, Oil Pump Cover Gasket, Service Valve ( Bolt) * Gasket, Bottom Plate Gasket, Pump End Bearing Head Shaft Seal (0D) Gasket, Motor End Cover Gasket, Cylinder Head --- Side Bank (Suction Cutoff Unloader) * NOTE: When ordering a Gasket Set be aware that it includes one (1) of item1 and for a Container Unit the quantity needed is two (). 49

55 NO TAG NO TAG

56 Date: Page 1 of 1 TO: GRABOWSKI D. GRABOWSKI Fax. No FROM: Bill Lindsey CARRIER TRANSICOLD DIV. P.O. BOX 480 SYACUSE, NY 11 Tel. No. Fax. No Please supply us with a quote on the following job specification: Manual: SERVICE PARTS LIST Form/T No.: T-7-01PL Quantity: 100 Reprint Quantity: 100 Date Required: TEN WORKING DAYS P.O. No.: Writer/Coordinator: Bill Lindsey (Based on reprint within months without changes) Manual Specifications: Text pages print Black. Final size, 8. x 11 saddle stitched. 0 lb. opaque white text stock. Three () hole drilled (/1 Dia.). Veloxes Silver Print Yes No Cover Specifications --- Stock: 80 lb. LOE Gloss (Warren) Color: Prints PMS --- TEAL GREEN plus Varnish Color bleeds four (4) sides, outside front and back cover. Manual Composition --- Includes: Camera Ready Pages 0 Negatives Supplied Pages Blanks Total Pages (Less cover) Art Work Supplied --- Includes: Camera Ready Art: 0 Oversized Line Art Work 0 Photograph(s) /window and line overlays Negatives Supplied Art: 0 Halftone(s) (incls. window and line neg.) 1 Line Neg. 1 Total Strip-ins Additional Comments: We require all negatives be returned at the completion of the job. 1. Follow supplied dummy copy for details.. Screen Carrier Transicold 0% on title page as indicated on dummy.. Strip-in supplied negative on Cover.

57 VENDOR INFORMATION T-7-01PL Printer Tel. No. Fax. No. Contact Price Reprint Quoted Price Eastwood Litho Russell Bartlett Dellas Graphics Jean Henry Grabowski Dick Grabowski $47.00 $1.00 $9. $101. $80.00 $ Syracuse Litho, Darryl Grandy Liverpool Litho, Mark Fingar Selco Graphics, Neale Bogardus Indicatesprinterwascalled.

58 December, 199 PARTS LIST UPDATE To: Holders of Service Parts List Manual T-7-01PL for the Model 9NT40-01 Container Refrigeration Unit. Please add the attachedrevised page 48 toyour manual. The revisionbar (J) indicates the changes made. If we can be of any further assistance please feel free to call. Paul J. Spaulding Technical Writer CTD Publications