Model 69NT T-258PL $3.00

Transcription

1 Model 69NT T-258PL $3.00

2 SERVICE PARTS LIST CONTAINER REFRIGERATION UNIT MODEL 69NT CONTENTS Introduction... i Ordering Instructions... i Letter Designations... i Model Chart... i 1. Quick List --- Clamps, Filter-drier, Fuse, Ty-raps, And Wire Terminals 1 2. Tools Refrigeration Unit Assembly Refrigeration Unit --- Front Control Box Door Control Box Control Box --- High Voltage Shield Removed Condenser Fan Motor And Coil Section Receiver And Tubing Section Evaporator Fan Motor And Access Panel Section Evaporator Coil Section --- Rear Panels Removed Evaporator Coil Section --- Rear Panels Attached Recording Thermometer (Partlow) Thermostatic Expansion Valve --- Alco Suction Solenoid Valve Suction Modulation Valve Makeup Air Cover Compressor Mounting And Gauges Voltage Option Labels and Decals Compressor --- Motor Assembly Service Replacement Compressor Terminal Mounting And Junction Box Group Service Valve Group Compressor --- Motor Body Group Pump End Group Crankshaft, Rod And Piston Group Valve Plate Group Gasket Set Carrier Transicold Division, Carrier Corporation, P.O. Box 4805, Syracuse, N.Y Carrier Corporation 1993 D Printed in U. S. A. 1093

3 SERVICE PARTS LIST INTRODUCTION This parts list identifies service replacement parts for the Carrier Transicold Container Model listed in the Model Chart below. ORDERING INSTRUCTIONS All orders and inquiries for parts must include: Model, Unit Serial Number, Part Number, description of part as shown on list and quantity required. Address all correspondence for parts to the following address: A/R NS LETTER DESIGNATIONS NLO NSA NSI NSS CARRIER TRANSICOLD DIVISION Replacement Component Group TR-20, P.O. Box 4805 Syracuse, New York The following letter designations are used to classify parts throughout this list: As Required. P-- Suffix P-- added to part number means part is available in packaged quantity only. Example: No Longer Offered. P/N P10 is a package of 10 P/N Use part number and P-- suffix Not Shown in the illustration. when ordering. Non-Stock Assembly --- order components listed under the assembly. Non-Stock Item --- may be available on special order. Not Sold Separately --- order next higher assembly or kit. MODEL CHART PL SST SV Purchase Locally. Stainless Steel Series unless otherwise specified. Suffix SV --- added to part number designates service replacement part. MODEL 69NT X X A --- Provision for water-cooled condenser. If water-cooled condenser is added, refrigerant charge will change. B --- Provision for step-up power transformer. X --- Designates item provided. i

4 1. QUICK LIST -- CLAMPS, FILTER-DRIER, FUSE, TY-RAPS, AND WIRE TERMINALS P10 Clamp, Tube, 1/4 --- SST P10 Clamp, Tube, 3/8 --- SST P10 Clamp, Tube, 1/2 --- SST P10 Clamp, Tube, 5/8 --- SST P10 Clamp, Tube, 3/4 --- SST P10 Clamp, Tube, 7/8 --- SST P10 Clamp, Tube, 1-1/8 --- SST P10 Clamp, Tube, 1-1/4 --- SST P10 Clamp, Tube, 1-3/8 --- SST P10 Clamp, Tube, 1-1/2 --- SST P25 Connector, Butt End, Wire Range to 16 Gauge P25 Connector, Butt End, Wire Range to 14 Gauge P25 Connector, Butt End, Wire Range to 10 Gauge P25 Connector, Closed End, Wire Range to 14 Gauge P25 Connector, Closed End, Wire Range to 10 Gauge 66U Filter-Drier HY10FJ006-P05 Fuse, Glass amp P05 Fuse, Glass amp P25 Ring Terminal, #6, Wire Range to 10 Gauge P25 Ring Terminal, #10, Wire Range to 10 Gauge P25 Ring Terminal, 3/8, Wire Range to 10 Gauge P25 Ring Terminal, 1/4, Wire Range to 10 Gauge P25 Ring Terminal, #10, Wire Range to 14 Gauge P25 Ring Terminal, 5/16, Wire Range to 14 Gauge P25 Ring Terminal, #10, Wire Range to 16 Gauge P25 Ring Terminal, 3/8, Wire Range to 14 Gauge P25 Spade Terminal,.032 x.250, Wire Range to 14 Gauge P25 Spade Terminal, 3/8, Wire Range to 10 Gauge F25 Spiral Wrap, 1/4 inch Diameter x 25 ft Long F25 Spiral Wrap, 1/2 inch Diameter x 25 ft Long 66U P10 Tube, Heat Shrink, 1/4 ID x 2.12 inches lg P25 Ty-Raps, 5-1/2 inches Long P25 Ty-Raps, 11 inches Long Series Wire Markers SW20 Compressor Oil, Castrol Icematic (Quart) Sealant, Pipe (Used to seal fittings on unit with R-134a) 2. TOOLS Temperature Tester (Simpson Meter) Temperature Test Lead (15 Foot) Temperature Test Lead (50 Foot) Adapter, Males (Both Ends) (Use with Temperature Tester) Case, Carrying (Used with ) Wrench, Compressor Sight Glass Inspection Light with Mirror Volt-Ohmmeter, Digital Amprobe Clamp (Used with ) Wrench, Service Valve Volt-Ohmmeter, Digital (Fluke) Pin Extender, Plug Connector Pliers, Crimping (Used for compressor terminal block replacement) Grip, Wire Vise (Used for compressor terminal block replacement) Crimper, Micro Contact Pins Kit, Static Dissipative (Used for working on electronic components) Ground Strap, Wrist --- Disposable (Used for working on electronic components) Gauge Set, Manifold (For R-134a) Detector, Leak Extractor, Integrated Circuit (For Eprom removal) Insertion, Integrated Circuit (For Eprom installation and pin straightener) 1

5 3. REFRIGERATION UNIT ASSEMBLY 3.1 REFRIGERATION UNIT -- FRONT

6 3.1 REFRIGERATION UNIT -- FRONT Panel, Access & Evaporator Fan Motor --- Refer to Section Labels and Decals --- Refer to Section Valve, Thermostatic Expansion (Location) --- Refer to Section Box, Control --- Refer to Sections 3.2 thru Coil, Condenser --- Refer to Section Receiver and Tubing --- Refer to Section Compressor --- Refer to Sections 3.15 & Cables, Power --- Refer to Section Guard, Compressor --- Refer to Section Cover, Makeup Air --- Refer to Section Thermometer, Recording --- Refer to Section Condenser Fan Motor & Fan --- Refer to Section

7 3.2 CONTROL BOX DOOR 27, RM MD ST controlled air temperature HINGE -- SECTIONAL VIEW 4

8 3.2 CONTROL BOX DOOR 1 66U Screw, Retaining Washer, Retaining Washer, Mylar, 3/8 ID x 1.00 OD NT Door Assembly --- Includes: 1 NS Gasket F50 Seal Rubber (50 ft, Cut to length) A/R 6 69NT Panel, Switch NT Label, CB1, CB NT Label, Switch, (RM, MD, ST) NT Label, Controlled Air Temperature (NSI) NT Label,Warning Hinge Protector, Mylar U Screw, Machine, #10-24 x 1/2 lg --- SST (NSI) Plate, Nut Protector, Mylar Washer, Mylar, 1/4 ID x 5/8 OD U Washer, Flat, # SST (NSI) U Washer, Lock, # SST (NSI) Receptacle, Remote Monitoring (Plastic) --- Optional 1 NS Plug, Remote Monitoring --- Optional U Gasket, Receptacle Cap and Chain (RM) Screw, Round Head, #4-40 x 5/8 lg --- SST (NSI) Locknut, # SST (NSI) Switch, Toggle (MDS) U Seal, Bushing 2 NS 69NT Adapter Strip Switch, Toggle (On--- Off) NT Label, Status Indicator (NSI) Indicator, Status (4 Light Bar) NT Label, Operating Instruction 1 5

9 3.3 CONTROL BOX 4 1,2,3 5,6,7 8 9, ,24 19,20,21, ,16,17 13,14 6

10 3.3 CONTROL BOX 1 69NT Switch Assembly (TDS & TSS) --- Includes: 1 NS NSS Connector Switch, Push Button (TDS) Switch, Toggle (TSS) NT Label, Switch (TSS,SDS,TDS,DIS) (NSI) NT Switch Assembly, Rotary (DIS) --- Includes: Switch, Rotary U Knob NT Shield, High Voltage --- Includes: U Stud, 1/4 Turn U Retainer NT Plate Assembly, Schematic & Diagram (NSI) CH Label, Danger --- High Voltage Receptacle U Rivet, Blind, 1/8 Diameter, Grip Range --- 1/32-1/8 --- SST (NSI) Fuse Block 1 16 HY10FJ006 Fuse, 6 amp U Screw, Pan Head, #6-32 x 7/16 lg --- SST (NSI) NT Label, Danger --- High Voltage (NSI) Temperature Selector (_F/_C) 1 20 AT39JA101 Nut, Hex, # SST (NSI) U Washer, Lock, #8 --- SST (NSI) U Screw, Pan Head, #8-32 x 3/8 lg --- SST (NSI) 8 NS 69NT Switch Assembly (For use with digital display) --- Optional --- Includes: Switch, Scale Selector (SSS) Switch, Set Temperature Display (SDS) 1 NS Plug 1 NS Contact, Socket Block, Terminal 1 7

11 3.4 CONTROL BOX -- HIGH VOLTAGE SHIELD REMOVED ,6,7 8,9,10 8,9, ,9,10 12,9, ,34,24, ,28,29,30,31 22,23,24,25, ,18,19, ,16,17 8

12 3.4 CONTROL BOX -- HIGH VOLTAGE SHIELD REMOVED Board, Power Supply and IRS Board, Power Supply and IRS --- Remanufactured Board, Timing and Current Control Board, Timing and Current Control --- Remanufactured Board, Temperature Control Board, Temperature Control --- Remanufactured Fuse, 3 amp Indicator, Status --- Refer to Section NT Angle, Status Indicator (NSI) NT Shield, Status Indicator (NSI) Contactor, Condenser/Evaporator Fan Motor and Heater (CF, EF & HR) U Screw, Hex Head, #10-24 x 1/2 lg --- SST (NSI) AU27JR131 Washer, Lock, # SST (NSI) U Receptacle Contactor, Compressor (C) Voltage Switch Knob --- Includes: 1 NS NSS Screw, Handle Circuit Breaker vac, 50 amp (CB2) U Screw, Pan Head, #6-32 x 5/16 lg --- SST 4 17 AU27JR081 Washer, Lock, #6 --- SST U Circuit Breaker vac (CB2) U Screw, Pan Head, #6-32 x 7/16 lg --- SST (NSI) 4 20 AC39QA163 Screw, Binding Head, 1/4-20 x 5/16 lg --- Brass (For Terminals) (NSI) U Transformer, Control (TR) Transformer, Current Limiting (CLT) --- Optional Cover, Plastic - Transformer Mounting (For use with CLT) U Washer, Lock, #8 --- SST (NSI) A/R 25 66U Screw, Pan Head, #8-32 x 3/4 lg --- SST (NSI) A/R 26 AT39JA171 Locknut, Hex Head, 1/ SST (NSI) SV Display, Digital --- Optional Display, Digital --- Remanufactured NT Plug, Harness (For Digital Display) --- Includes: Plug (6 position) Standoff (For use with digital display) Standoff (For use with digital display) Relay Board, Main Printed Circuit U Standoff 10 NS Humiseal, 12 oz. A/R NS Lubricant, Contact A/R 9

13 3.5 CONDENSER FAN MOTOR AND COIL SECTION 6,7,8,9, ,13,

14 3.5 CONDENSER FAN MOTOR AND COIL SECTION 1 69NT Cover, Condenser Coil U Screw, Hex Head, #10-24 x 1/2 lg --- SST (NSI) A/R 3 66U Washer, Flat, # SST (NSI) A/R 4 69NT Washer, Fender,.063 Thick --- SST (NSI) A/R 5 66U Washer, Lock, # SST (NSI) A/R 6 69NT SV Coil, Condenser --- Copper (Includes Mylar washers and protectors) U Capscrew, Hex Head, 1/4-20 x 3/4 lg --- SST (NSI) U Washer, Flat, 1/4 --- SST Washer, Mylar, 1/4 ID x 3/4 OD A/R Washer, Mylar, 1/4 ID x 1.00 OD A/R NS Washer, Mylar, 13/64 ID x 39/64 OD A/R NS Protector, Mylar (Apply between coil mounting & frame RH side) 1 NS Protector, Mylar (Apply to top side center coil mounting) 1 NS Protector, Mylar (Apply between coil mounting & frame, RH & LH sides) 2 NS Protector, Mylar (Apply to center between frame & coil & coil cover) 2 NS Protector, Mylar (Apply to top side of coil bracket, RH & LH sides) 2 NS Protector, Mylar (Apply under coil center bracket attached to frame) 1 NS Protector, Mylar (Apply between coil & coil cover, RH & LH sides) 2 NS Protector, Mylar (Apply between coil mounting & frame LH side) NT Grille, Condenser --- Includes: Stud (1/4 Turn) Washer, Retaining Receptacle NT Hinge, Condenser Fan Grille NT Venturi, Condenser Fan 1 NS 66U Rivet, Blind, 5/32 Diameter, Grip Range---1/8-1/4 --- SST (NSI) A/R Fan, Condenser --- SST --- Includes: 1 18 PL Set Screw,Square Head,5/16-24 x 5/8 lg --- SST SV Motor, Condenser Fan --- Includes: 1 NS Bearing 2 NS Capacitor 1 20 PL Key, 3/16 Square x 1-3/8 lg --- SST U Screw, Hex Head/Washer, 5/16-18 x SST Washer, Flat, 5/ SST (NSI) Washer, Mylar Locknut, 5/ SST (NSI) NT Protector, Condenser Fan Motor Mounting 2 11

15 3.6 RECEIVER AND TUBING SECTION ,9,10, ,13,14 10,13,

16 3.6 RECEIVER AND TUBING SECTION 1 66U Valve, Liquid Line --- Includes: Cap, Flare --- 1/ Cap, Valve Elbow, Swivel, 90_ 1/4 Flare x M Brass Coupling, M Brass --- Includes: Cap, Service Port Indicator, Moisture --- Liquid (Brass) U Filter-Drier NP Clamp, Filter-Drier --- Includes: 1 NS F16 Gasket, Clamp (16 FT, cut to length) A/R 10 66U Screw, Hex Head, 1/4-20 x 3/4 lg --- SST (NSI) Washer, Mylar, 1/4 ID x 1.00 OD Valve, High Side Pressure Relief U Washer, Flat, 1/4 --- SST A/R Protector Protector, Mylar NT Receiver (Optional) --- Painted Steel --- Includes: NT Receiver (Optional) --- SST --- Includes: 1 NS Glass, Sight SV Sensor, Supply Temperature (STS) Valve, Pressure Regulator Valve, Modulating Solenoid --- Refer to Section Valve, Suction Solenoid --- Refer to Section Valve, Quench, Thermostatic Expansion 1 13

17 3.7 EVAPORATOR FAN MOTOR AND ACCESS PANEL SECTION 9 10,11, ,17, EFM-2 (Location) EFM-1 (Location)

18 3.7 EVAPORATOR FAN MOTOR AND ACCESS PANEL SECTION 1 69NT Panel, Access --- Includes: Gasket U F20 Gasket, Access Panel Seal --- Adhesive Back, Pressure Sensitive, 4x1/2thick(20ft,Cuttosize) A/R 4 AA06JA170 Capscrew, Hex Head, 1/4-20 x 1.00 lg --- SST 24 5 AN96OC416 Washer, Flat, 1/4 --- SST Washer, Mylar,1/4 ID X 1/2 OD NT Panel, Access --- Includes: Gasket NT Bracket, Motor Mount U Capscrew, Hex Head, 5/16-18 x 1-1/4 lg --- SST (NSI) Washer, Flat, 5/ SST (NSI) Locknut, 5/ SST (NSI) Motor, Evaporator Fan --- Includes: 2 NS Bearing 2 NS Capacitor 1 14 PL Key, 3/16 x 3/16 x 1-3/8 lg --- SST Fan, Evaporator (EFM-1) --- Includes: Fan, Evaporator (EFM-2) --- Includes: 1 NS PL Setscrews, 5/16-24 x 5/8 lg --- SST U Bolt, Hex Head, 3/8-16 x 1.00 lg --- SST (NSI) U Washer, Flat, 3/8 --- SST (NSI) 8 18 AU11JR241 Washer, Lock, 3/8 --- SST 8 15

19 3.8 EVAPORATOR COIL SECTION -- REAR PANELS REMOVED 4 3 6,7,8 19,

20 3.8 EVAPORATOR COIL SECTION -- REAR PANELS REMOVED 1 69NT Shield Assembly, Rain --- Humidistat (NSI) --- Optional Humidistat (HCS) --- Optional SV Sensor, Thermistor (RTS) Sensor, Thermistor --- Temp. Recorder (Refer to Section 3.10 ) Thermostat, Suction Solenoid U Thermostat, Defrost Termination, 75_F (24_C) (DTT) Capscrew, Hex Head, #8-32 x 1/2 lg --- SST (NSI) U Washer, Lock, #8 --- SST (NSI) U Thermostat, Heat Termination, 130_F (54_C) (HTT) 1 10 AA06JA166 Capscrew, Hex Head, 1/4-20 x 1/2 lg --- SST (NSI) Washer, Lock, 1/4 --- SST (NSI) 9 *12 69NT Coil, Evaporator 1 NS 69NT Retainer U Screw, Hex Head, 1/4-20 x 3/4 lg --- SST (NSI) U Washer, Flat, 1/4 --- SST U Screw, Lag, Hex Head, 1/4-10 x 2.00 lg --- SST Heater, Drain Pan (DPH) U Heaters, Evaporator Coil 4 NS 69NT Clip, Heater Exchanger, Heat Capscrew, Hex Head, 1/4-20 x 1-1/4 lg --- SST (NSI) NT Washer, Fender, 1/4 x 1/16 thick --- SST (NSI) Plug, Hole, Nylon --- Black (For 2.00 Dia. hole located on fan deck) A/R * Note: Does not include thermostats or heaters. 17

21 3.9 EVAPORATOR COIL SECTION -- REAR PANELS ATTACHED NT Grille, Top U Rivet, Blind, 5/16 Diameter, Grip Range --- 1/8-1/4 (NSI) A/R 3 69NT Panel Assembly, Upper --- Includes: 1 NS NSS Drain Pan, Side 2 NS NSS Drain Pan, Center U Rivet, Blind, 1/4 Diameter, Grip Range --- 1/8-3/16 (NSI) A/R 5 66U Rivet, Blind, 1/4 Diameter, Grip Range --- 3/16-1/4 (NSI) A/R 6 69NT Panel, Bottom NT Panel, Bottom, Left-hand Side U Screw, Machine, Truss Head, #10-24 x 1/2 lg --- SST (NSI) NT Washer, Fender, #10 x 1.00 OD --- SST (NSI) 19 NS 66U F25 Gasket (25 ft, Cut to length) A/R 18

22 3.10 RECORDING THERMOMETER (PARTLOW) Recording Thermometer --- Includes: Cover Assembly (Bottom Latch) --- Includes: 1 NS Seal, Cover --- Rubber 1 NS Gasket, Cover Glass Glass, Cover 1 NS Catch Assembly, Cover Stylus Kit --- Includes: 1 4 NSS Screw, Round Head, #2-56 x 3/16 lg Mechanism Assembly Push Rod (Includes Setscrews) Clip, Key Mounting Key, Clock Winding Nut and Chain, Chart (Sonceboz Clock) Nut and Chain, Chart (Gluck Clock) 1 10 PL Screw, Round Head #6-32 x 5/ Platen, Chart Flange, Chart Drive (Sonceboz) Flange, Chart Drive (Gluck) Clock, 31 Day, CCW (Counterclockwise) Stand, Mounting, Chart Drive Case (Top Hinge) O-Ring, Element Flange Element, 9 ft lg --- Includes: 1 NS Sensor, Thermistor (Accessory 344 and Jack) ft lg 1 NS Pin (Use with Partlow Thermister Assembly) Screw, Flange (NSI) 2 NS Charts _F Day (Box of 50) (---20_F to+80_f) A/R NS Charts _C Day (Box of 50) (---25_C to+25_c) A/R 19

23 3.11 THERMOSTATIC EXPANSION VALVE -- Alco Alco Part Nos. A625-3A 2 A625-4A A625-2A A625-5A 5 6 A625-7A A625-4A Kit, Repair --- Includes: 1 2 NSS PowerHeadAssemblyandGasket,Item5 1 3 NSS Cage Assembly and Gasket, Item U Gasket Set, Universal --- Includes: 1 5 NSS Gasket, Body Flange A625-4A 2 6 NSS Gasket, Seat --- A625-2A U Flange, Body (NSI) 1 NS Coupling, M8 --- Brass --- Includes: 1 NS Cap, Service Port 1 20

24 3.12 SUCTION SOLENOID VALVE ALCO Solenoid Valve, Suction --- Includes: Cap, Snap Coil Kit, Repair Kit, Repair Diaphragm 1 21

25 3.13 SUCTION MODULATION VALVE * Kit, Enclosing Tube & Coil Housing --- Includes: Nut, Coil --- Includes: 1 3 NSS Nut, Coil 1 4 NSS O-Ring, Coil Nut Housing, Coil --- Includes: 1 6 NSS Housing, Coil 1 *7 NSS Plate, Coil Bottom 1 8 NSS O-Ring, Coil Bottom Plate 1 9 NSS Sleeve, Solenoid Coil 1 10 NSS Tube Assembly, Coil Plate & Enclosing Valve, Suction Modulaton --- Includes: Coil, Solenoid --- Includes: 1 9 NSS Sleeve, Solenoid Coil 1 * NOTE: Item 7, Coil Bottom Plate is only supplied in Kit as a separate item for use on early style Enclosing Tube Assemblies. 22

26 3.14 MAKEUP AIR COVER NT NT Cover, Makeup Air --- Includes: U Washer, Flat, 1/4 --- SST Nut, Hex, 1/4-20 UNC-2B --- SST (NSI) NT Gasket, Cover (NSI) NT Gasket, Cover (NSI) 1 23

27 3.15 COMPRESSOR MOUNTING AND GAUGES ,7,8, ,16,17, without gauges with gauges COMPRESSOR FOOT CUTAWAY VIEW CENTER CYLINDER HEAD VIEW 24,25,26,27 26,27,28,29 30 UNIT SECTIONAL VIEW 24

28 3.15 COMPRESSOR MOUNTING AND GAUGES Compressor --- Refer to Section Snubber Assembly U Switch, High Pressure NT Tube Assembly, High Pressure NT Tube Assembly, Low Pressure Used with pressure gauges NT Stiffener Assembly 1 NS 66U Screw, Hex Head, #10-24 x 3/4 lg --- SST Used to mount 2 NS 66U Washer, Flat, # SST (NSI) stiffener assembly NT Bracket Assembly, Gauge --- Optional Gauge, Suction Pressure --- Optional Gauge, Discharge Pressure --- Optional 1 10 CA21JA051 Tee, 1/4 NPT (NSI) DA Valve Assembly, Core, Check --- Brass Used with pressure gauges Valve, Low Side Pressure Relief 1 NS --- Valve, High Side Pressure Relief --- Refer to Section Tee, Male, 1/4 fpt x 1/4 fpt x 1/4 mpt --- Brass (NSI) NT Protector (Compressor to Compressor Base) 1 15 AU11JR241 Washer, Lock, 3/8 --- SST 2 16 AA06JA232 Capscrew, Hex Head, 3/8-16 x 1-1/4 lg --- SST (NSI) Washer, Flat, 3/8 --- SST Washer, Mylar, 3/8 ID x 1.00 OD NT Base, Compressor 1 NS 66U Bolt, Hex Head, 3/8-16 x 1.00 lg --- SST (NSI) Used to mount 7 NS 66U Washer, Flat, 3/8 --- SST (NSI) compressor base 7 NS AU11JR241 Washer, Lock, 3/8 --- SST to unit frame 7 NS Washer, Mylar, 3/8 ID x 1.00 OD U Capscrew, 7/16-14 x 2-3/4 lg --- SST (NSI) Locknut, 7/ SST (NSI) U Washer, Flat, 7/ SST Washer, Mylar, 1/2 ID x 1-1/8 OD NT Panel, Guard (NSI) U Screw, Hex Head, 1/4-20 x 3/4 lg --- SST (NSI) Washer, Mylar, 3/8 ID x 1-1/4 OD A/R 27 66U Washer, Flat, 1/4 --- SST A/R 28 66U Capscrew, Hex Head, 1/4-20 x 1-1/2 lg --- SST (NSI) A/R Locknut, Hex Head, 1/ SST (NSI) A/R 30 69NT Guard, Compressor 1 NS Oil, Compressor (Quart) A/R 25

29 3.16 VOLTAGE OPTION 1 2 3,4,5 10,11 6,7,9 6,7,9 6,7,8 26

30 3.16 VOLTAGE OPTION Plug, Hole, Dupont Zytel --- Black (For 3/8 to 13/32 diameter hole) A/R Plug, Hole, Nylon --- Black (For 1/4 diameter hole in doghouse wall) A/R 3 69NT SV Cover, Voltage Selector Switch --- Includes: U Hinge (Cut to length) U Rivet, Hollow, 3/32 Diameter, Grip Range --- 5/16-3/8 --- SST U Screw, Hex Head, Thread Cutting, #10-24 x 3/4 lg --- SST Washer, Mylar, 0.25 ID x 1.00 OD Clamp, Cushioned, Tube, 7/8 OD Clamp, Cushioned, Tube, 3/4 OD U Cable, Power (460 vac, Extra Heavy Duty -- Black) (NSI) Plug, Power (460 vac) -- MENNEKES 1 NS Bushing (for P/N ) (NSI) 4 27

31 3.17 LABELS AND DECALS

32 3.17 LABELS AND DECALS Decal, Carrier Transicold U Label, Direction Arrow Label, Fan Warning --- Refer to Section Label, Operating Instruction (NSI) --- Refer to Section NT Label, Voltage Selector (VS) (NSI) Label, CB1, CB2 --- Refer to Section Label, Charge with R-134a Only (NSI) Label, POE Compressor Oil Label, R-134a --- Ozone Protection (NSI) CH Label, Arrow (NSI) NT Label, Air Exchange (NSI) 1 NS --- Plate Assembly, Schematic & Diagram --- Refer to Section

33 4. COMPRESSOR -- MOTOR ASSEMBLY Existing parts on compressor terminal block O-ring Bushing Terminal block Terminal post Wire assembly 1/2 Inch diameter heat shrink tubing Compressor junction block 1/4 Inch diameter heat shrink tubing 30

34 4.1 SERVICE REPLACEMENT COMPRESSOR SV Compressor, 41 CFM, 230/460 vac/3 ph/60 hz 1 NOTE The Service Replacement Motor --- Compressor is sold without terminal box and cover, and without shut-off valves (but with valve pads). Customer should retain the original terminal box and valves for use on replacement compressor. 4.2 TERMINAL MOUNTING AND JUNCTION BOX GROUP 2 69NT Cover, Junction Box U Screw, Hex Head, #10-24 x 1/2 lg (cover to box) U Washer, Lock, #10 (cover to box) (NSI) NT SV Box, Junction (Located on Front of Compressor) --- Includes: NT SV Box, Junction (Located on Back of Compressor) --- Includes: NT Cover, Junction Box 1 6 AD61JA124 Screw, Pan Head, #10-32 x 3/8 lg (box to compressor) (NSI) Terminal, Compressor (5 Terminals) Terminal, Compressor (6 Terminals) Kit, Compressor Terminal Wiring 1 NS Kit, Compressor Terminal Wiring (Dual Voltage or Dual/Single Voltage) 1 NS Gasket, Terminal Plate Washer, Mylar A/R 4.3 SERVICE VALVE GROUP Elbow, 1/4 NPTF x M Brass Coupling, M Brass --- Includes: Cap, Service Port Valve, Suction Shut-Off, 1-1/8 ODS --- Includes: Cap, Seal 1 NS Gasket, Seal Cap Gasket, Suction Service Valve Valve, Discharge Shut-Off, 7/8 ODS --- Includes: Cap, Seal 1 NS Gasket, Seal Cap Gasket, Discharge Service Valve U Bolt, Hex Head, 5/16-18 x 1-7/8 lg --- SST (NSI) Gasket, Bolt, 5/ Elbow, 1/8 NPTF x M Brass Coupling, M Brass --- Includes: Cap, Service Port COMPRESSOR -- MOTOR BODY GROUP NS --- Gasket Set (Refer to Section 4.8) Head, Cylinder --- Side Bank (Shaved Head) Head, Cylinder --- Center Bank Screw, Hex Head --- Center Head, 3/8-16 x 3.00 lg --- SAE Grade Gasket, Cylinder Head (Side Bank) Screw, Hex Head, 3/8-16 x 2.00 lg --- SAE Grade Screw, Hex Head, 3/8-16 x 1.00 lg --- SAE Grade Screen Assembly, Oil Filter Tube, Oil Suction Valve, Oil Relief Sight Glass Package, Oil Level --- Includes: Gasket, Sight Glass Cover, Motor End (NSI) Gasket, Motor End Cover Screw, Hex Head, 7/16-14 x 1-1/4 lg --- SAE Grade 5 (NSI) 18 31

35 4.4 COMPRESSOR -- MOTOR BODY GROUP (CONTINUED) Plate, Bottom Gasket, Bottom Plate Screw, Hex Head, 3/8-16 x 2.00 lg --- SAE Grade Strainer Assembly, Suction (NSI) 1 47 PL Plug, Pipe, Oil Fill, 1/ Check Valve Assembly, Oil Return Plate, Screen Hold Down 1 50 PL Pipe Plug (High & Low Pressure Connection and Oil Drain), 1/4-18 NPT Gasket, Cylinder Head (Center) PUMP END GROUP Screw, Hex Head, Bearing Head, 3/8-16 x 1.00 lg --- SAE Grade Gasket, Capscrew, 3/ Bearing Head & Gear Oil Pump Package Washer, Thrust Gasket, Cover Plate CRANKSHAFT, ROD AND PISTON GROUP 70 N/A Crankshaft Washer, Thrust Pin, Spiral, 5/32 Diameter x 5/8 lg Key, Rotor Drive Washer, Rotor (NSI) Washer, Star, Rotor, 5/8 (NSI) Tube Assembly, Equalizer (NSI) Piston & Pin Pkg (Standard) --- Includes: Piston & Pin Pkg (+0.020) --- Includes: A/R 78 NSS Piston Pin, Piston Retainer, Piston Pin Ring, Compression (For Standard & inch Piston) Connecting Rod and Cap Assembly (Standard) --- Includes: Connecting Rod and Cap Assembly (+0.010) --- Includes: 6 NS Pin, Dowel Capscrew --- Special (Epoxy Coated) VALVE PLATE GROUP Package, Valve Plate Assembly (Center and Side Banks -- Canted) --- Includes: 3 NS NSS Plate Assembly, Valve --- Includes: 1 91 NSS Plate, Valve Valve, Discharge Valve, Stop Discharge Screw, Hex Head, 1/4-28 x 3/8 lg Washer, Lock, 1/ Valve, Suction Spring, Suction Valve Positioning Gasket, Cylinder Head (Side Bank) Gasket, Cylinder Head (Center) Gasket, Valve Plate Pin, Dowel (Valve Plate) 12 32

36 4.8 GASKET SET * Gasket Set --- Includes: Gasket, Suction Service Valve (4 Bolt) Gasket, Shaft Seal (05G) Gasket, Valve Plate (05G) Gasket, End Flange (05G) --- Includes: Gasket, Flange Spacer (05G) Gasket, Cylinder Head --- Right and Left (Standard) Gasket, Valve Plate Gasket, Cylinder Head --- Center Gasket, Cylinder Head --- Right and Left (Hot Gas Bypass Unloader) Gasket, Oil Supply Tube (O-Ring, 05D) Gasket, Sight Glass Gasket, Unloader Body Gasket, Oil Pump Cover Gasket, Service Valve (2 Bolt) 2 * Gasket, Bottom Plate Gasket, Pump End Bearing Head Shaft Seal (05D) Gasket, Motor End Cover Gasket, Cylinder Head (Suction Cutoff Unloader) 2 * NOTE: When ordering a Gasket Set (P/N ) be aware that it includes one (1) of item15 and for a Container Unit the quantity required is two (2). 33