Model 69NT T-259PL Rev F Change 12/96

Transcription

1 Model 9NT T-59PL Rev F Change 1/9

2 SERVICE PARTS LIST CONTAINER REFRIGERATION UNIT MODEL 9NT Carrier Transicold Division, Carrier Corporation, P.O. Box 4805, Syracuse, N.Y. 131 Carrier Corporation 1995 D Printed in U. S. A. 1195

3 TABLE OF CONTENTS Introduction... ii Ordering Instructions... ii Letter Designations... ii Model Chart... iii 1. Quick List --- Clamps, Filter-Drier, Fuse, Ty-Raps, and Wire Terminals Tools Refrigeration Unit Assembly Refrigeration Unit --- Front Control Box Door (Prior to Model 9NT ) Control Box Door (Starting with Model 9NT & -31) 3.4 Control Box Control Box --- High and Low Voltage Shields Removed Prior to Serial Number Control Box --- High and Low Voltage Shields Removed Starting with Serial Number Control Box --- Module Section Condenser Fan Motor and Coil Section Receiver and Tubing Section Water-Cooled Condenser Evaporator Fan Motor and Access Panel Section Evaporator Coil Section --- Rear Panels Removed Evaporator Coil Section --- Rear Panels Attached Recording Thermometer (Partlow) Prior To Serial Number Recording Thermometer (Partlow) Starting With Serial Number Recording Thermometer (Saginomiya) Thermostatic Expansion Valve --- Alco Suction Solenoid Valve --- Alco Modulating Solenoid Valve Compressor Mounting And Related Components Voltage Options Autotransformer Options Nitrogen Feed Fresh Air Makeup Vent Labels and Decals Interrogator and Accessories DataReader Portable/Personal Computers Huskey 1/80 Computer Interrogator Receptacle Compressor --- Motor Assembly Service Replacement Compressor Terminal Mounting and Junction Box Group Service Valve Group Compressor --- Motor Body Group Pump End Group Crankshaft, Rod and Piston Group Valve Plate Group Gasket Set Options Controller and Configuration Cards DataCORDER and Configuration Cards... 4 i

4 INTRODUCTION This service parts list identifies service replacement parts for the Carrier Transicold container Models listed in the Model Chart. Separately bound manuals covering the CTD Controlled Atmosphere option are also supplied, see chart below: Manual Number T-5 T-5PL Equipment Covered Controlled Atmosphere option Controlled Atmosphere option Type of Manual Operation and Service Service Parts List ORDERING INSTRUCTIONS All orders and inquiries for parts must include: Model, Unit Serial Number, Part Number, Description of part as shown on list and quantity required. Address all correspondence for parts to the following address: LETTER DESIGNATIONS CARRIER TRANSICOLD DIVISION Replacement Components Group, TR-0 P.O. Box 4805, Syracuse, New York 131 or FAX to: (315) The following letter designations are used to classify parts throughout this list: A/R NLO NS NSA NSI NSS P-- PL SST SV As Required. No Longer Offered. Not Shown in the illustration. Non-Stock Assembly --- order components listed under the assembly. Non-Stock Item --- may be available on special order. Not Sold Separately --- order next higher assembly or kit. Suffix P-- added to part number means part is available in packaged quantity only. Example: P/N P10 is a package of 10 P/N Use part number and P-- suffix when ordering. Purchase Locally. Stainless Steel Series unless otherwise specified. Suffix SV --- added to part number designates service replacement part. ii

5 MODEL CHART NOTE Models listed below may or may not include certain components (i.e., Transformer, DataCORDER, Battery Packs for the Controller or DataCORDER, Temperature Recorder), it will be up to the end user to ascertain if their unit model includes these components. MODELS Voltage Switch e Controlled Atmosphere Option 9NT X X X X X NT A X X X X NT X NT A C X X --- X X --- H --- 9NT A --- X X X NT A C X X --- X X NT D X X X X X NT A --- X X --- X X NT X --- X X --- X X NT A C X X --- X X NT A C X X --- X X --- I --- 9NT A X X X X NT A X X X X --- X NT A B X X X NT A C X X --- X X NT A C X X --- X X NT A B X X X X 9NT A C X X --- X X NT X D X X X X X X X NT E X C X X --- X G --- 9NT M X --- X X --- X G --- 9NT C X X --- X X NT X C X X --- X X G --- 9NT A B X X K NT A B X X X NT A X X X X NT A --- X X X --- H --- 9NT A B X X X X 9NT A B X X X NT X --- X X X X H X 9NT A E X X X NT A X X X X NT A C X X --- X X NT A C X X --- X X --- H --- 9NT A C X X --- X X NT A B X X NT A X X X X NT X X X X 9NT X --- X X X X H --- 9NT A C X X --- X X NT A B X X X NT A C X X --- X X iii

6 MODEL CHART (Continued) MODELS Voltage Switch e Controlled Atmosphere Option 9NT X --- X X K X 9NT X --- X X --- X X NT A C X X --- X X NT A E X X X --- H --- 9NT A B X X X NT A B X X X NT D X X X X X NT A C X X --- X X NT A X X --- X NT A C X X --- X X --- I --- 9NT A D X X X X X X X J 9NT A E X X X NT A C X X --- X X NT A E X X X A B C D E F G H I J K X --- Provision for USDA Cold Treatment. --- Provision for Dual Voltage Intergral Transformer. --- Factory installed Dual Voltage Intergral Transformer. --- Factory installed Dual Voltage Evaporator Transformer. --- Factory Installed Dual Voltage Modular Transformer. --- Provision for Dual Voltage Modular Transformer. --- Factory installed CTD CA option. --- Factory installed Transfresh CA option. --- Provision for Transfresh CA option. --- Provision for Communications Interface Module (RMU). --- Provision for Temperature Recorder. --- Features that apply to model. iv

7 PART NO. DESCRIPTION 1. QUICK LIST -- CLAMPS, FILTER-DRIER, FUSE, TY-RAPS, AND WIRE TERMINALS P10 Clamp, Tube, 1/4 --- SST P10 Clamp, Tube, 3/8 --- SST P10 Clamp, Tube, 1/ --- SST P10 Clamp, Tube, 5/8 --- SST P10 Clamp, Tube, 3/4 --- SST P10 Clamp, Tube, 7/8 --- SST P10 Clamp, Tube, 1-1/8 --- SST P10 Clamp, Tube, 1-1/4 --- SST P10 Clamp, Tube, 1-3/8 --- SST P10 Clamp, Tube, 1-1/ --- SST P5 Connector, Butt End, Wire Range --- to 1 Gauge P5 Connector, Butt End, Wire Range to 14 Gauge P5 Connector, Butt End, Wire Range to 10 Gauge P5 Connector, Closed End, Wire Range --- to 14 Gauge P5 Connector, Closed End, Wire Range to 10 Gauge U Filter-Drier P05 Fuse, 5 Amp (F, F1 & F) P05 Fuse, 15 Amp (F3) P5 Ring Terminal, #, Wire Range to 10 Gauge P5 Ring Terminal, #10, Wire Range to 10 Gauge P5 Ring Terminal, 3/8, Wire Range to 10 Gauge P5 Ring Terminal, 1/4, Wire Range to 10 Gauge P5 Ring Terminal, #10, Wire Range to 14 Gauge P5 Ring Terminal, 5/1, Wire Range to 14 Gauge P5 Ring Terminal, #10, Wire Range --- to 1 Gauge P5 Ring Terminal, 3/8, Wire Range to 14 Gauge P5 Spade Terminal, 1/4 x 5/1, Wire Range to 14 Gauge P5 Spade Terminal, 3/8, Wire Range to 10 Gauge F5 Spiral Wrap, 1/4 Diameter x 5 ft lg F5 Spiral Wrap, 1/ Diameter x 5 ft lg U P10 Tube, Heat Shrink, 1/ ID x -3/4 lg P5 Ty-Raps, 5-1/ inches lg P5 Ty-Raps, inches lg Series Wire Markers Sealant, Pipe (Used to seal fittings on unit with R-134a) Cleaner, Coil. TOOLS Temperature Tester (Simpson Meter) Temperature Test Lead (15 Foot) Temperature Test Lead (50 Foot) Adapter, Males (Both Ends) (Use with Temperature Tester) Case, Carrying (Used with ) Wrench, Compressor Sight Glass Inspection Light with Mirror Volt-Ohmmeter, Digital Amprobe Clamp (Used with ) Wrench, Service Valve Volt-Ohmmeter, Digital (Fluke) Pliers, Crimping (Used for compressor terminal block replacement) Grip, Wire Vise (Used for compressor terminal block replacement) Kit, Static Dissipative (Used for working on electronic components) Ground Strap, Wrist (Used for working on electronic components) SW0 Compressor Oil, Castrol Icematic (Quart) Gauge Set, Manifold, Fahrenheit/PSI Gauge Set, Manifold, Centigrade/KPA Detector, Leak Extractor, Pin (Used on Fan Motor Plugs and Interrogator Plugs) Crimper, Pin (Used on Fan Motor Plugs and Interrogator Plugs) 1

8 3. REFRIGERATION UNIT ASSEMBLY 3.1 REFRIGERATION UNIT -- FRONT Revised 1//9

9 ITEM PART NO. DESCRIPTION QTY 3.1 REFRIGERATION UNIT -- FRONT Panel, Access & Evaporator Fan Motor --- Refer to Section Labels and Decals --- Refer to Section Motor, Condenser Fan --- Refer to Section NT Gutter, Rain --- Optional Box, Control --- Refer to Sections 3. to NT Handle, Fixed --- Optional Coil, Condenser --- Refer to Section Receiver, Water-Cooled Condenser or --- Refer to Section 3.9 or NT40-57 Handle, Hinged --- Optional Compressor --- Refer to Sections 3.0 or Cable, Power --- Refer to Section Plug, Power --- Refer to Section Guard, Compressor --- Refer to Section NT Cable Assembly, A3C (Transfresh) (NSI) 1 NS 9NT Cable Assembly, Rear (Transfresh) (NSI) 1 NS 9NT Cable, Power --- AC (Transfresh) (NSI) 1 NS 9NT Hose Assembly, Air (Transfresh) (NSI) 1 NS 9NT Fuse Assembly, In-line (Transfresh) (NSI) Connector, Interrogator --- Refer to Section Cover, Makeup Air --- Refer to Section Recording Thermometer (Optional) --- Refer to Sections 3.14 to NT35-91 Cover, Blank (For units w/out a Recording Thermometer) --- (NSI) 9NT , NT4-544 Cover, Blank (For units w/out a Recording Thermometer) --- 9NT NT43-04 Cover, Blank (For units w/out a Recording Thermometer) --- (NSI) 9NT ,-59, NT Gutter, Rain --- Optional 1 3

10 3. CONTROL BOX DOOR (Prior to Model 9NT , Excluding ) Control Box Control Box Door HINGE ASSEMBLY -- SECTIONAL VIEW DOOR ASSEMBLY -- PARTIAL BACK VIEW Revised 1//9 4

11 ITEM PART NO. DESCRIPTION QTY 3. CONTROL BOX DOOR (Prior to Model 9NT , Excluding ) 1 NLO Door Assembly --- Includes: (Refer to section 3.3 for new door assy) Gasket, Door SV Window, Control Box Door --- Lexan --- Includes: Gasket, Window 1 5 U Rivet, Closed, 3/1 Diameter, Grip Range --- 1/4-3/8 --- SST (NSI) 1 9NT35-78 Plate, Window, 0.90 Thick ---Aluminum (NSI) 7 9NT Plate, Window, 0.90 Thick ---Aluminum (NSI) 8 U Screw, Retaining Washer, Retaining Washer, Mylar, 0.50 ID x OD 11 U Screw, Retaining Hinge Assembly (NSI) --- Includes: NS Hinge, Half 1 NS Hinge, Half 1 NS Pin Assembly, with Tether 1 13 U Washer, Flat, # SST Protector, Mylar (Hinge) Retainer, Nut Protector, Mylar (Hinge) 17 U Screw, Truss Head, #10-4 x 3/4 lg --- SST (NSI) 4 18 U Washer, Lock, # SST Washer, Mylar, 0.05 ID x 0.00 OD Pocket, Placecard Locknut, Hex Head, # SST (NSI) 3 U Screw, #10-4 x 1/ lg --- SST (NSI) 4 3 U Washer, Flat, # SST 4 5

12 3.3 CONTROL BOX DOOR (Starting with Model 9NT & -31) Control Box Control Box Door HINGE ASSEMBLY -- SECTIONAL VIEW DOOR ASSEMBLY -- PARTIAL BACK VIEW Revised 1//9

13 ITEM PART NO. DESCRIPTION QTY 3.3 CONTROL BOX DOOR (Starting with Model 9NT & -31) 1 9NT Door Assembly --- Includes: Gasket, Door SV Window and Gasket Assembly, Control Box Door --- Lexan --- Includes: Nut, Push-on --- SST Washer, Retaining U Screw, Retaining Washer, Mylar, 0.50 ID x OD 8 U Screw, Retaining Hinge Assembly (NSI) --- Includes: NS Hinge, Half 1 NS Hinge, Half 1 NS Pin Assembly, with Tether Protector, Mylar (Hinge) Retainer, Nut Protector, Mylar (Hinge) 13 U Screw, Truss Head, #10-4 x 3/4 lg --- SST (NSI) 4 14 U Washer, Lock, # SST 7 15 U Washer, Flat, # SST Washer, Mylar, 0.05 ID x 0.00 OD NT Pocket, Placecard Locknut, Hex Head, # SST (NSI) 3 19 U Screw, #10-4 x 1/ lg --- SST (NSI) 4 0 U Washer, Flat, # SST 4 7

14 3.4 CONTROL BOX Revised 1//9 8

15 ITEM PART NO. DESCRIPTION QTY 3.4 CONTROL BOX 1 9NT Plate, Schematic & Diagram (NSI) 9NT40-489,-11 & 9NT Prior to Serial # NT Plate, Schematic & Diagram (NSI) 9NT NT Plate, Schematic & Diagram (NSI) 9NT & 9NT Prior to Serial # NT Plate, Schematic & Diagram (NSI) 9NT ,-7,-8,-9 & 9NT Prior to Serial # NT Plate, Schematic & Diagram (NSI) 9NT ,-9 -- Prior to Serial # NT Plate, Schematic & Diagram (NSI) 9NT Prior to Serial # NT Plate, Schematic & Diagram (NSI) 9NT , NT Plate, Schematic & Diagram (NSI) 9NT ,-3,-5, -59,-1,-4,-,-7,-70,-71 & 9NT Starting with Serial # NT Plate, Schematic & Diagram (NSI) 9NT Starting with Serial # NT Plate, Schematic & Diagram (NSI) 9NT ,-15,-18,-1, -54,-5,-58,-3,-5,-8,-77,-79,-83 & 9NT ,-9 -- Starting with Serial # NT Plate, Schematic & Diagram (NSI) 9NT ,-5,-0 & 9NT Starting with Serial # NT Plate, Schematic & Diagram (NSI) 9NT Starting with Serial # NT Plate, Schematic & Diagram (NSI) 9NT NT Plate, Schematic & Diagram (NSI) 9NT ,-9,-81, NT Plate, Schematic & Diagram (NSI) 9NT NT Plate, Schematic & Diagram (NSI) 9NT NT Plate, Schematic & Diagram (NSI) 9NT , NT41-97 Plate, Schematic & Diagram (NSI) 9NT E,-0M, NT43-50 Plate, Schematic & Diagram (NSI) 9NT NT Plate, Schematic & Diagram (NSI) 9NT U1-403 Screw, Truss Head, #10-4 x 1/ lg --- SST 3 9NT43-15 Shield, High Voltage (Plastic) --- Includes: Hinge Rivet, Blind, 1/8 Diameter, Grip Range --- 1/8-3/1 --- SST (NSI) Stud & Retainer Package --- Includes: NS NSS Stud, Fastener 1 NS NSS Retainer, Fastener Stud Receptacle Guide, Low Voltage Shield (NSI) 1 9 9NT43-14 Shield, Low Voltage (Lexan) --- With Tether NT35-17 Label, Welding Precautions (NSI) NT Label, Welding Precautions (NSI) 9NT , NT Label, Welding Precautions (NSI) 9NT CH Label, Danger-High Voltage 1 9

16 3.5 CONTROL BOX -- HIGH AND LOW VOLTAGE SHIELDS REMOVED -- PRIOR TO SERIAL NUMBER UNITS WITH SINGLE-SPEED EVAPORATOR MOTORS UNITS WITH DUAL-SPEED EVAPORATOR MOTORS Revised 1//9 10

17 ITEM PART NO. DESCRIPTION QTY 3.5 CONTROL BOX -- HIGH AND LOW VOLTAGE SHIELDS REMOVED -- PRIOR TO SERIAL NUMBER Contactor, Condenser Fan Motor, Heater & Evaporator Fan Motor (EF) 3 U Screw, Pan Head, (Thread Cutting) #8-3 x 3/4 lg --- SST (NSI) A/R 3 9NT Panel, Contactor (NSI) Spacer (For Contactor Panel) (NSI) Screw, Hex Head, 1/4-0 x 1.00 lg --- SST (NSI) Circuit Breaker vac 50 Amp (CB) (See Model Chart) Plate, Blank (For units w/o CB) (NSI) --- Optional 1 7 U Screw, Pan Head, #-3 x 5/1 lg --- SST (NSI) Washer, Lock, # --- SST (NSI) A/R 9 U Circuit Breaker vac (CB1) 1 10 U Screw, Pan Head, #-3 x 7/1 lg --- SST (NSI) Receptacle, Retaining (For Control Box Door) Receptacle, Remote Monitoring (RM) (Plastic) --- Optional 1 NS Plug, Remote Monitoring --- Optional Cap and Tether, Receptacle Assembly --- Optional 1 14 U1-835 Gasket, Remote Monitoring Receptacle --- Optional Screw, Round Head, #4-40 x 5/8 lg --- SST (NSI) 4 1 U Washer, Flat, 0.15 ID --- SST (NSI) Nut, Self Locking, # SST Switch, Toggle (On-Off) Circuit Breaker (1 Amp) (On-Off) 9NT U1-975 Seal, Bushing A/R Plate, Switch (NSI) Plate, Switch (NSI) 9NT Switch, Toggle (MDS) 1 U F07 Trim, Flexible (7 ft, Cut to length) A/R 3 9NT35-77 Bracket, Voltage Switch (NSI) 1 4 U Washer, Flat, # SST A/R 5 U Screw, Hex Head, (Thread Cutting) #10-4 x 1/ lg --- SST (NSI) A/R Switch,Voltage (See Model Chart) --- Includes: Handle --- Includes: 1 8 NSS Screw, Handle Transformer, Base Unit 1 30 U Screw, Hex Head, #10-4 x 1/ lg --- SST (NSI) A/R Contactor, Compressor (40 Amp) Contactor, Compressor (0 Amp) 9NT , Contactor, Evaporator Fan Motor (ES) (See Model Chart) Switch,Voltage (See Model Chart) Handle (See Note) --- Includes: 1 NS NSS Screw, Handle Handle (See Note) --- Includes: 1 NS SV Tightening Element 1 NOTE: See illustration for handle identification. 11

18 3. CONTROL BOX -- HIGH AND LOW VOLTAGE SHIELDS REMOVED -- STARTING WITH SERIAL NUMBER UNITS WITH SINGLE-SPEED EVAPORATOR MOTORS UNITS WITH DUAL-SPEED EVAPORATOR MOTORS Revised 1//9 1

19 ITEM PART NO. DESCRIPTION QTY 3. CONTROL BOX -- HIGH AND LOW VOLTAGE SHIELDS REMOVED -- STARTING WITH SERIAL NUMBER Contactor, Condenser Fan Motor, Heater & Evaporator Fan Motor (EF) 3 U Screw, Pan Head, (Thread Cutting) #8-3 x 3/4 lg --- SST (NSI) A/R 3 9NT35-37 Panel, Contactor (NSI) 1 3 9NT Panel, Contactor (NSI) 9NT NT Panel, Contactor (NSI) 9NT E,-0M Spacer (For Contactor Panel) (NSI) Screw, Hex Head, 1/4-0 x 1.00 lg --- SST (NSI) Circuit Breaker vac 50 Amp (CB) (See Model Chart) Plate, Blank (For units w/o CB) (NSI) --- Optional 1 7 U Screw, Pan Head, #-3 x 5/1 lg --- SST (NSI) Washer, Lock, # --- SST (NSI) A/R 9 U Circuit Breaker vac (CB1) 1 10 U Screw, Pan Head, #-3 x 7/1 lg --- SST (NSI) Receptacle, Retaining (For Control Box Door) Receptacle, Remote Monitoring (RM) (Plastic) --- Optional 1 NS Plug, Remote Monitoring --- Optional Cap and Tether, Receptacle Assembly --- Optional 1 14 U1-835 Gasket, Remote Monitoring Receptacle --- Optional Screw, Round Head, #4-40 x 5/8 lg --- SST (NSI) 4 1 U Washer, Flat, 0.15 ID --- SST (NSI) Nut, Self Locking, # SST Switch, Toggle (On-Off) Circuit, Breaker (1 Amp) (On-Off) 9NT , U1-975 Seal, Bushing A/R Plate, Switch (NSI) Plate, Switch (NSI) 9NT ,-50,-58,-1,-,-,-8, -77,-78,-80, Plate, Switch (NSI) 9NT Plate, Switch (NSI) 9NT Switch, Toggle (MDS) 1 U F07 Trim, Flexible (7 ft, Cut to length) A/R 3 9NT35-77 Bracket, Voltage Switch (NSI) 1 4 U Washer, Flat, # SST A/R 5 U Screw, Hex Head, (Thread Cutting) #10-4 x 1/ lg --- SST (NSI) A/R Switch,Voltage (See Model Chart) --- Includes: Handle --- Includes: 1 8 NSS Screw, Handle Transformer, Base Unit Transformer (0 Amp) 9NT E,-0M, U Screw, Hex Head, #10-4 x 1/ lg --- SST (NSI) A/R Contactor, Compressor (40 Amp) Contactor, Compressor (0 Amp) 9NT ,-1,-19, Contactor, Evaporator Fan Motor (ES) (See Model Chart) Switch,Voltage (See Model Chart) Handle (See Note) --- Includes: 1 NS NSS Screw, Handle Handle (See Note) --- Includes: 1 NS SV Tightening Element Connector, Auxilary --- N.C NT ,31 1 NOTE: See illustration for handle identification. 13

20 3.7 CONTROL BOX -- MODULE SECTION Revised 1//9 14

21 ITEM PART NO. DESCRIPTION QTY 3.7 CONTROL BOX -- MODULE SECTION Module, Display --- NEW Module, Display --- Remanufactured 1 U Screw, Hex Head, #10-4 x 1/ lg --- SST (NSI) A/R 3 9NT Washer, Fender, 0.03 Thick --- SST (NSI) Module, Controller --- Refer to Section Includes: Module, DataCORDER --- Refer to Section. --- Includes: --- U Screw, Hex Head, #10-4 x 1/ lg --- SST (NSI) 1 9NT35-9 Washer, Fender, 0.03 Thick --- SST (NSI) Retainer, Screw, ID (NSI) 1 8 U1-403 Screw, Truss Head, #10-4 x 1/ lg --- SST Washer, Mylar, 0.05 ID x 0.00 OD 10 9NT Pad, Key --- Includes: Gasket (Between Key Pad Plate Assembly and Connector) (NSI) Gasket (Between Key Pad and Key Pad Plate Assembly) (NSI) NT41-13 Plate Assembly, Key Pad Mounting (NSI) Battery Pack --- DataCORDER Module --- Optional Label, DataCORDER Software Programming Port (NSI) --- Refer to Section Battery Pack --- Controller Module --- Optional Label, Controller Config ID (NSI) --- Refer to Section SV Module, Communications Interface (RMU) 9NT ,-30, Includes: SV Module, Communications Interface (RMU) 9NT ,- --- Includes: 1 19 U Fastener 4 0 U Retainer Module, High Voltage --- NEW Module, High Voltage --- Remanufactured Card, Controller Configuration Software --- Refer to Section Card, DataCORDER Configuration Software --- Refer to Section Fuse, 15 Amp (F3) Fuse, 5 Amp (F, F1 & F) 3 NS --- Card, Controller Operation Software --- Refer to Section NS --- Card, DataCORDER Operation Software --- Refer to Section. --- NS 9NT43-1 Wire Harness, High Voltage Module to Controller Module 1 NS Wire Harness, Display Module to Controller Module 1 NS Wire Harness, Key Pad to Display Module 1 NS Wire Harness, Controller to DataCORDER 1 15

22 3.8 CONDENSER FAN MOTOR AND COIL SECTION For Models 9NT , -, -31 & 9NT and up Revised 1//9 1

23 ITEM PART NO. DESCRIPTION QTY 3.8 CONDENSER FAN MOTOR AND COIL SECTION 1 9NT Cover, Condenser Coil 1 1 9NT43-10 Cover, Condenser Coil 9NT E,-0M,- 1 9NT43-0-SV Coil, Condenser (Copper row enhanced) 9NT Includes Mylar Washers 1 9NT43-0-4SV Coil, Condenser (Copper --- row enhanced) 9NT & Includes Mylar Washers 1 NS 9NT Protector (Apply between frame and coil & coil cover) 4 3 U Capscrew, Hex Head, 1/4-0 x 3/4 lg --- SST (NSI) 10 4 U Washer, Flat, 1/4 --- SST Washer, Mylar,1/4 ID X 3/4 OD Washer, Mylar,1/4 ID X 1.00 OD NS Washer, Mylar,13/4 ID X 39/4 OD NS Protector, Mylar (Apply between coil mounting & frame RH side) 1 NS Protector, Mylar (Apply to top side center coil mounting) 1 NS Protector, Mylar (Apply between coil mounting & frame, RH & LH sides) NS Protector, Mylar (Apply to center between frame & coil & coil cover) NS Protector, Mylar (Apply to top side of coil bracket, RH & LH sides) NS Protector, Mylar (Apply under coil center bracket attached to frame) 1 NS Protector, Mylar (Apply between coil & coil cover, RH & LH sides) NS Protector, Mylar (Apply between coil mounting & frame LH side) 1 7 9NT Bracket, Condenser Motor Mount 1 8 9NT Grille --- Includes: Stud, 1/4 Turn Washer, Retaining Receptacle 1 9NT Venturi (For 17-1/ diameter Fan) 1 NS PL Rivet, Blind, 5/3 Diameter, Grip Range---1/8-5/8 --- SST Hinge 9NT NS PL Rivet, Blind, 5/3 Diameter, Grip Range---1/1-1/8 --- SST Fan, Condenser (17-1/ diameter) --- Composite --- Includes: 1 15 PL Set Screw,Square Head, 5/1-4 x 5/8 lg --- SST SV Motor, Condenser Fan 9NT SV Motor, Condenser Fan --- Includes: SV Motor, Condenser Fan 9NT includes: 1 17 PL Key, 3/1 Square x 1-3/8 lg --- SST 1 NS Bearing NS Capacitor 1 18 U1-531 Screw, Hex Head, 5/1-18 x 1-1/4 lg --- SST (NSI) Washer, Flat, 5/1 --- SST (NSI) Washer, Mylar, 1.0 OD x 3/8 ID Locknut, 5/ SST (NSI) 4 9NT35-11 Protector, Condenser Fan Motor Mounting 3 9NT43-8 Grille and Venturi Assembly Fan, Condenser (17-1/ diameter) --- Composite --- Includes: 1 15 PL Set Screw,Square Head, 5/1-4 x 5/8 lg --- SST Washer, Mylar, 13/4 ID x 39/4 OD U Screw, Retaining Washer, Retaining --- Nylon Hinge 9 U1-403 Screw, Truss Head, #10-4 x 1/ lg --- SST 4 30 U Washer, Lock, # SST 4 31 U Washer, Flat, # SST Protector, Mylar (Apply between Grille Hinge and Frame) Protector, Mylar (Apply between Grille and Retaining Nut) Nut, Retaining 17

24 3.9 RECEIVER AND TUBING SECTION (SRS) 0 (STS) Revised 1//9 18

25 ITEM PART NO. DESCRIPTION QTY 3.9 RECEIVER AND TUBING SECTION 1 U Valve, Liquid Line Starting with Serial # U Valve, Liquid Line --- Includes: Cap, Flare --- 1/ Cap, Valve Elbow, Swivel, 90_ 1/4 Flare x M Brass Coupling, M Brass --- Includes: Cap, Service Port Sensor, Ambient Thermistor (AMBS) Indicator, Liquid Moisture --- Brass 1 9 U Filter-Drier NP Clamp --- Includes: 1 NS F1 Gasket (1 ft, Cut to length) A/R 11 U Screw, Hex Head, 1/4-0 x 3/4 lg --- SST (NSI) Washer, Mylar, 1/4 ID x 1.00 OD Plug, Fusible, 3/8 mpt --- Brass 1 14 U Washer, Flat, 1/4 --- SST Protector, Mylar Washer, Mylar, 0.50 ID x OD NT41-3- Receiver --- SST (See Model Chart) --- Includes: NT Receiver --- Painted Steel -- 9NT ,-8,-14,-1,-1,- & -5,-54,-58,-59,-,-7,-70, Includes: Glass, Sight, 1/ npt NS Glass, Sight, with Red Balls, 1/ npt Protector, Mylar SV Sensor Assembly (STS & SRS) Sensor, Thermistor (CPDS) 9NT , Valve, Pressure Regulator Receptacle, 4 Pin (SSV/SMV) Lock, Secondary, 4 Pin (SSV/SMV) Contact, Pin #1 (SSV/SMV) Plug, 4 Pin (SSV/SMV) Lock, Secondary, 4 Pin (SSV/SMV) Contact, Socket #1 (SSV/SMV) Valve, Modulating Solenoid --- Refer to Section U Bolt, Hex Head, 3/8-1 x 1.00 lg --- SST (NSI) 1 31 AU11JR41 Washer, Lock, 3/8 --- SST 1 3 U Washer, Flat, 3/8 --- SST (NSI) Washer, Mylar, ID x 1.00 OD DA Valve, Schrader 9NT , Transducer, Pressure (Condenser Pressure Control) 9NT , Valve, Suction Solenoid --- Refer to Section Valve, Quench, Thermostatic Expansion --- includes: 1 NS Repair Kit --- includes: 1 NS NSS Power Head Sensor, Thermistor (CPSS) 9NT ,- 1 19

26 3.10 WATER-COOLED CONDENSER Revised 1//9 0

27 ITEM PART NO. DESCRIPTION QTY 3.10 WATER-COOLED CONDENSER --- 9NT4-914 Kit, Condenser/Receiver (For Field Installation) --- Includes: 1 1 9NT Condenser/Receiver (See Model Chart) --- Includes: Sight Glass --- Includes: 1 3 NSS Ball, Float Protector, Mylar Protector, Mylar 1 U Coupling (Water-In) 1 7 U-114 Cap, Dust Coupling, Self Draining --- Includes: Seal, O-Ring 1 10 U-115 Cap, Dust SV Switch, Water Pressure Disc, Rupture, 3/8 npt 1 13 U Bolt, Hex Head, 3/8-1 x 1.00 lg --- SST (NSI) 1 14 U Washer, Flat, 3/8 --- SST (NSI) 1 15 AU11JR41 Washer, Lock, 3/8 --- SST Washer, Mylar, 3/8 ID x 1.00 OD 1 17 U Capscrew, Hex Head, 1/4-0 x 3/4 lg --- SST (NSI) A/R 18 U Washer, Flat, 1/4 --- SST A/R Washer, Mylar, 1/4 ID x 13/1 OD 1

28 3.11 EVAPORATOR FAN MOTOR AND ACCESS PANEL SECTION EFM- (Location) EFM-1 (Location) Revised 1//9

29 ITEM PART NO. DESCRIPTION QTY 3.11 EVAPORATOR FAN MOTOR AND ACCESS PANEL SECTION 1 9NT Panel, Access --- Includes: 1 9NT Panel, Access 9NT Includes: Gasket 1 3 U F0 Gasket, Access Panel Seal --- Adhesive Back, PressureSensitive,4x1/thick(0ft,Cuttolength) A/R 4 AA0JA170 Capscrew, Hex Head, 1/4-0 x 1 lg --- SST 4 5 AN9OC41 Washer, Flat, 1/4 --- SST Washer, Nylon,1/4 ID X 0.40 OD 4 7 9NT Panel, Access --- Includes: 1 7 9NT Panel, Access 9NT Includes: Gasket 1 9 9NT Bracket, Motor Mount Capscrew, Hex Head, 5/1-18 x 1-1/4 lg --- SST (NSI) Washer, Flat, 5/1 --- SST (NSI) Locknut, 5/ SST (NSI) SV Motor, Evaporator Fan (One-Speed) (See Model Chart) --- Includes: 14 PL Key, 3/1 Square x 1-3/8 lg --- SST 1 NS Bearing NS Capacitor, 15 µf (microfarads) Motor, Evaporator Fan (Two-Speed) (See Model Chart) --- Includes: 14 PL Key, 3/1 Square x 1-3/8 lg --- SST 1 NS Bearing NS Capacitor 1 NS Relay, Motor 1 NS Capacitor, 0 µf (microfarads) Fan, Evaporator (EFM-1) --- Includes: 1 NS PL Setscrews, 5/1-4 x 5/8 lg --- SST Fan, Evaporator (EFM-) --- Includes: 1 NS PL Setscrews, 5/1-4 x 5/8 lg --- SST 1 U Bolt, Hex Head, 3/8-1 x 1.00 lg --- SST (NSI) 8 17 U Washer, Flat, 3/8 --- SST (NSI) 8 18 AU11JR41 Washer, Lock, 3/8 --- SST NT40-47 Bracket, Mounting 4 3

30 3.1 EVAPORATOR COIL SECTION -- REAR PANELS REMOVED (RTS)(RRS) NT , -, -5 Revised 1//9 4

31 ITEM PART NO. DESCRIPTION QTY 3.1 EVAPORATOR COIL SECTION -- REAR PANELS REMOVED SV Sensor Assembly (RRS & RTS) --- Sensor, Thermistor (Recording Thermometer) --- Refer to Sections 3.14, 3.15 or Sensor, Thermistor, Defrost (DTS) Screw, Hex Head, #8-3 x 1/ lg --- SST (For mounting DTS) (NSI) 1 5 U Thermostat, Heat Termination (HTT) 1 PL Washer, Lock, #8 --- SST 4 7 PL Capscrew, Hex Head, 1/4-0 x 1/ lg 1 8 PL Washer, Lock, 1/4 --- SST NT Coil, Evaporator (Does not include thermostats or heaters) 1 9 9NT Coil, Evaporator (Does not include thermostats or heaters) 9NT , -50 & up 1 NS 9NT35-5 Retainer (For Heaters) 1 NS 9NT35-53 Clip (For Heaters) 4 10 PL Capscrew, Hex Head, 1/4-0 x 3/4 lg --- SST 9 11 PL Washer, Flat, 1/4 A/R 1 PL Screw, Lag, 1/4 x lg Valve, Thermostatic Expansion --- (Location) Refer to Section Tee, 1/4 x 1/4 x 1/4, SAE --- Brass Coupling, M8 --- Brass --- Includes: Cap, Service Port Heater, Drain Pan Kit, USDA (For Field Installation) (For units provisioned for rear-mounted USDA) --- Includes: --- NS 9NT Plate Assembly, USDA (NSI) Receptacle (PR1, PR, PR3) (NSI) NT Cap, Dust, with Tether (3 Pin Receptacle) Receptacle, Interrogator (ICR) (NSI) 1 1 9NT43-17 Cap, Dust, with Tether (5 Pin Receptacle) Contact, Pin #1 (Used with & ) Plug, Sealing 3 NS Plug, Socket (ICR) --- Optional 1 4 9NT Cap, Dust, with Tether (3 Pin Receptacle) Receptacle (PR1, PR, PR3, Cargo Probe 4) (NSI) Cap and Chain Receptacle, Interrogator Pin 1 * Socket, Contact (Silver Plated) A/R * Socket, Contact (Gold Plated) A/R NS Sensor Assembly (USDA Probe) --- Optional --- Includes: 3 NS Plug, Socket (PR1, PR, PR3, Cargo Probe 4) --- Optional 1 NS Contact, Socket #1 (Used with & ) A/R Exchanger, Heat 1 30 PL Capscrew, Hex Head, 1/4-0 x 1-1/4 lg --- SST NT Washer, Fender, 1/1 Thick SST (NSI) Heater, Evaporator Coil Plug, Hole ( inch diameter) (Located on Fan Deck) Sensor, Humidity (HS) (See Model Chart) 1 35 U Screw, Hex Head, #10-4 x 1.00 lg --- SST --- Optional (NSI) 4 3 U Washer, Flat, # SST (NSI) 37 9NT41-18 Bracket Assembly, Humidity Sensor --- Optional (NSI) 1 * NOTE: Do not mix silver pins with gold pins and sockets. 5

32 ITEM PART NO. DESCRIPTION QTY 3.13 EVAPORATOR COIL SECTION -- REAR PANELS ATTACHED MODELS -- 9NT40-489,-1,-3,-5,-8,-9,-10,-11,-13,-14,-15,-17,-18,-3,-5,-,-9,-30, -31,-51,-5,-54,-5,-58,-59,-0,-3,-4,-5,-7,-8,-9,-70,-71,-79,-80,-81,-83,-84 UNITS WITH BOLTED PANELS 1 9NT40-14 Grille, Top Rivet, Blind, 5/1 Diameter, Grip Range --- 1/8-1/4 (NSI) A/R 3 U Rivet, TIR, 3/1 Diameter, Grip Range --- 5/4-11/4 (NSI) 4 4 9NT Panel Assembly, Upper --- Includes: 1 NS NSS Drain Pan, Side NS NSS Drain Pan, Center 1 5 9NT Panel, Bottom Rivet, Blind, 1/4 Diameter, Grip Range --- 1/8-3/1 (NSI) A/R 7 9NT35-57 Duct, Air (Location --- Behind Bottom Panel) (NSI) Rivet, Blind, 1/4 Diameter, Grip Range --- 3/1-1/4 (NSI) A/R Rivet, Blind, 1/8 Diameter, Grip Range --- 1/4-5/1 --- SST (NSI) NT Spacer, Hinge (NSI) 11 9NT35-9 Plate (NSI) (Location) 1 9NT40-57 Door, Access --- Includes: 1 NS U Hinge Stud, 1/4 Turn, 0.97 lg Washer, Lock Receptacle, Retaining 3 1 9NT Panel, Bottom, Side (For heat exchanger) 1 17 U1-403 Screw, Machine, Truss Head, #10-4 x 1/ lg --- SST NT35-9 Washer, Fender, #10 x 1.00 OD --- SST 19 NS U F5 Gasket (5 ft, Cut to length) A/R Revised 1//9

33 ITEM PART NO. DESCRIPTION QTY 3.13 EVAPORATOR COIL SECTION -- REAR PANELS ATTACHED (CONTINUED) MODELS -- 9NT ,-,-7,-1,-50,-1,-,-,-75,-77,-78 UNITS WITH BOLTED PANELS 19 9NT40-14 Grille, Top Rivet, Blind, 5/1 Diameter, Grip Range --- 1/8-1/4 (NSI) A/R 1 U Rivet, TIR, 3/1 Diameter, Grip Range --- 5/4-11/4 (NSI) 4 9NT Panel Assembly, Upper --- Includes: 1 NS NSS Drain Pan, Side NS NSS Drain Pan, Center Rivet, Blind, 1/4 Diameter, Grip Range --- 1/8-3/1 (NSI) A/R Rivet, Blind, 1/4 Diameter, Grip Range --- 3/1-1/4 (NSI) A/R 5 9NT Panel, Bottom 1 9NT35-57 Duct, Air (Location --- Behind Bottom Panel) (NSI) Not used on NT Panel, Bottom (Provision for heat exchanger location) 1 8 U1-403 Screw, Machine, Truss Head, #10-4 x 1/ lg --- SST NT35-9 Washer, Fender, #10 x 1.00 OD --- SST 19 NS U F5 Gasket (5 ft, Cut to length) A/R 7

34 ITEM PART NO. DESCRIPTION QTY 3.13 EVAPORATOR COIL SECTION -- REAR PANELS ATTACHED (CONTINUED) MODEL -- 9NT ,-1,-19 UNITS WITH HINGED PANELS 30 9NT40-14 Grille, Top Rivet, Blind, 5/1 Diameter, Grip Range ---1/8-1/4 (NSI) NT40-34 Panel, Upper --- Includes: 1 NS NSS Drain Pan, Center 1 NS NSS Drain Pan, Side 33 9NT Panel, Bottom NT35-57 Duct, Air (Location --- Behind Bottom Panel) (NSI) Rivet, Blind, 1/4 Diameter, Grip Range --- 1/8-3/1 (NSI) Rivet, Blind, 1/4 Diameter, Grip Range --- 3/1-1/4 (NSI) NT40-57 Door, Access --- Includes: 1 NS U Hinge Stud, 1/4 Turn, 0.97 lg Washer, Retaining Receptacle, Retaining Rivet, Blind, 1/8 Diameter, Grip Range --- 1/4-5/1 (NSI) 0 4 9NT Spacer, Hinge (NSI) 43 9NT35-9 Plate, Stiffener (NSI) 44 9NT Plate, Bottom, Side (For Heat Exchanger access) NT35-38 Hinge Stud, 1/4 Turn, 0.97 lg Stud, 1/4 Turn, 1.0 lg 1 NS U F5 Gasket (5 ft, Cut to length) A/R Revised 1//9 8

35 ITEM PART NO. DESCRIPTION QTY 3.13 EVAPORATOR SECTION -- REAR PANELS ATTACHED MODEL -- 9NT E,-0M,- UNITS WITH HINGED PANELS 48 9NT43-11 Grille, Top Hinge --- SST Rivet, Blind, 1/8 Diameter, Grip Range --- 3/1-1/4 (NSI) NT40-34 Panel, Upper --- Includes: 1 NS NSS Drain Pan, Center 1 NS NSS Drain Pan, Side 5 9NT Panel, Bottom, Middle Rivet, Blind, 1/8 Diameter, Grip Range --- 1/8-3/1 (NSI) 54 9NT Panel, Bottom, Right Side NT40-57 Door, Access --- Includes: 1 NS U Hinge Stud, 1/4 Turn, 0.97 lg Washer, Retaining Receptacle, Retaining Rivet, Blind, 1/8 Diameter, Grip Range --- 1/4-5/1 (NSI) 0 0 9NT Spacer, Hinge (NSI) 1 9NT35-9 Plate, Stiffener (NSI) 9NT Panel, Bottom, Left Side 1 3 9NT35-38 Hinge Rivet, Blind, 5/3 Diameter, Grip Range ---3/1-1/4 (NSI) Stud, 1/4 Turn, 0.97 lg Stud, 1/4 Turn, 1.0 lg 1 NS U F5 Gasket (5 ft, Cut to length) A/R

36 3.14 RECORDING THERMOMETER (PARTLOW) -- PRIOR TO SERIAL NUMBER Revised 1//9 30

37 ITEM PART NO. DESCRIPTION QTY 3.14 RECORDING THERMOMETER (PARTLOW) -- PRIOR TO SERIAL NUMBER NLO Recording Thermometer --- Includes: (Refer to section 3.15 for new recording thermometer assy) Cover Assembly (Bottom Latch) --- Includes: 1 NS Seal, Cover --- Rubber SV Glass, Cover --- includes: 1 NS Gasket, Cover Glass 1 NS Catch Assembly, Cover Kit, Stylus --- Includes: 1 4 NSS Screw, Round Head, #-5 x 3/1 lg Mechanism Assembly Rod, Push (Includes Setscrews) Clip, Key Mounting Key, Clock Winding Nut and Chain, Chart (Sonceboz Clock) Nut and Chain, Chart (Gluck Clock) 1 10 PL Screw, Round Head #-3 x 5/ Platen, Chart Flange, Chart Drive (Sonceboz) Flange, Chart Drive (Gluck) Clock, 31 Day, CCW (Counterclockwise) Stand, Mounting, Chart Drive Case (Top Hinge) O-Ring, Element Flange Element, 9 ft lg --- Includes: 1 NS Sensor, Thermistor (Accessory 344 and Jack) ft lg 1 NS -043 Pin (Use with Partlow Thermistor Assembly) Screw, Flange (NSI) NS Charts _F Day (Box of 50) (---0_F to+80_f) A/R NS Charts _C Day (Box of 50) (---5_C to+5_c) A/R NS Kit, Hinge Replacement --- Includes: --- NS NSS Hinge and Hardware 1 NS Latch Kit, Hold Open 1 31

38 3.15 RECORDING THERMOMETER (PARTLOW) -- STARTING WITH SERIAL NUMBER Revised 1//9 3

39 ITEM PART NO. DESCRIPTION QTY 3.15 RECORDING THERMOMETER (PARTLOW) -- STARTING WITH SERIAL NUMBER * Recording Thermometer --- Includes: 1 * Recording Thermometer (without Simpson probe) 9NT ,-8,-9,-79, Includes: Cover Assembly (Bottom Latch) --- Includes: 1 NS Seal, Cover --- Rubber SV Glass, Cover --- includes: 1 NS Gasket, Cover Glass 1 NS Catch Assembly, Cover Kit, Stylus --- Includes: 1 4 NSS Screw, Round Head, #-5 x 3/1 lg Mechanism and Platen Assembly Main Lever and Push Rod Assembly (Includes Setscrews) Rod, Push Key, Clock Winding Nut and Chain, Chart (Sonceboz Clock) Nut and Chain, Chart (Gluck Clock) 1 10 PL Screw, Round Head #-3 x 5/ Flange, Chart Drive (Sonceboz) Flange, Chart Drive (Gluck) Clock, 31 Day, CCW (Counterclockwise) Case (Top Hinge) (Use with P/N ) Case (Top Hinge) (Use with P/N ) O-Ring, Element Flange Element, 9 ft lg (Use with P/N ) Element, 9 ft lg (Use with P/N ) --- Includes: 1 NS Sensor, Thermistor (Accessory 344 and Jack) ft lg 1 NS -043 Pin (Use with Partlow Thermistor Assembly) Screw, Flange (NSI) NS Charts _F Day (Box of 50) (---0_F to+80_f) A/R NS Charts _C Day (Box of 50) (---5_C to+5_c) A/R NS Kit, Hinge Replacement --- Includes: --- NS NSS Hinge and Hardware 1 NS Latch Kit, Hold Open 1 * NOTE: Mounting Kit P/N must be used if the Partlow Recorder P/N is replaced with Partlow Recorder P/N or on units prior to serial number

40 3.1 RECORDING THERMOMETER (SAGINOMIYA) Revised 1//9 34

41 ITEM PART NO. DESCRIPTION QTY 3.1 RECORDING THERMOMETER (SAGINOMIYA) Recording Thermometer --- Includes: Stylus, Lift Arm --- Prior to Saginomiya lot# xxx4, see Note Stylus, Lift Arm --- Starting with Saginomiya lot# xxx5, see Note Element Assembly --- Prior to Saginomiya lot# xxx4, see Note Element Assembly --- Starting with Saginomiya lot# xxx5, see Note Voltage Indicator, Plate Assembly & --- See Notes 1 & --- Includes: Indicator, Voltage Plate, Recorder 1 PL Battery (Mallory R14P/S 1.5 vdc) Shaft, Chart Block, Terminal (NSI) Timer (31 Day) Nut, Chart (Male) NT Sensor Assembly, Return Temperature (Optional) --- Includes: 1 NS Sensor, Thermistor Jack, Phono (Optional) 13 9NT Box Assembly, Recorder (NSI) Gasket, Door NT Door Assembly, Recorder Box 1 1 U Screw, Retaining NS Washer, Retaining Receptacle, Retaining 18 9NT Window, Lexan NT Gasket, Window (NSI) 1 0 9NT Bracket, Window Mounting (NSI) 1 1 9NT Plate, Window Mounting PL Nut, Hex Head, # SST 4 3 PL Washer, Lock, # SST 4 4 9NT40-39 Hinge Assembly Protector, Mylar (For Hinge) 4 NS Charts _C Day (Box of 50) (---5_C to+5_c) A/R NS Charts _F Day (Box of 50) (---0_F to+80_f) A/R NOTE 1: NOTE : Therecorderlotnumberislocatedonalabelattachedtotherecorderbody.Therewillbea four digit code. The last digit will determine the correct replacement part number (i.e., If the Saginomiya lot number is xxx4 or lower, then P/N is used. If the Saginomiya lot number is xxx5 or higher, then P/N is used.) Recorders with lot numbers xxx4 and lower will require the replacement of the recorder plate when replacing the P/N voltage indicator with the P/N voltage indicator, order P/N plate assembly & voltage indicator. 35

42 ITEM PART NO. DESCRIPTION QTY 3.17 THERMOSTATIC EXPANSION VALVE -- Alco Alco Part Nos. A5-3A A5-4A A5-A 5 3 NO TAG A5-5A 5 4 A5-7A A5-4A Kit, Repair --- Includes: Kit, Repair --- Includes: 9NT Kit, Repair --- Includes: 9NT Kit, Repair 9NT & and up --- Includes: 1 NSS PowerHeadAssemblyandGasket,Item5 1 3 NSS Cage Assembly and Gasket, Item 1 4 U1-5 Gasket Set, Universal --- Includes: 1 5 NSS Gasket, Body Flange A5-4A NSS Gasket, Seat --- A5-A 1 7 U Flange, Body (NSI) SUCTION SOLENOID VALVE -- Alco Solenoid Valve, Suction --- Includes: Cap, Snap Coil Kit, Repair Kit, Repair Diaphragm 1 Revised 1//9 3

43 ITEM PART NO. DESCRIPTION QTY 3.19 MODULATING SOLENOID VALVE * Kit, Enclosing Tube & Coil Housing --- Includes: Nut, Coil --- Includes: 1 3 NSS Nut, Coil 1 4 NSS O-Ring, Coil Nut Housing, Coil --- Includes: 1 NSS Housing, Coil 1 * 7 NSS Plate, Coil Bottom 1 8 NSS O-Ring, Coil Bottom Plate 1 9 NSS Sleeve, Solenoid Coil 1 10 NSS Tube Assembly, Coil Plate & Enclosing Valve, Modulating Solenoid --- Prior to Serial# Includes: Valve, Modulating Solenoid --- Starting with Serial# Includes: Coil, Solenoid --- Includes: 1 9 NSS Sleeve, Solenoid Coil Core, Valve (Scrader Valve) (Use with P/N ) Cap, Service (Use with P/N ) 1 * NOTE: Coil bottom plate is only supplied in Kit as a separate item for use on early style enclosing tube assemblies. 37

44 3.0 COMPRESSOR MOUNTING AND RELATED COMPONENTS Center Cylinder Head View with gauges Center Cylinder Head View without gauges Compressor Foot -- Cutaway View Center Cylinder Head View with Compressor Pressure Transducers Option Unit -- Sectional View Unit -- Sectional View for models 9NT ,-5,-9,-10,-13,-14,-15,-17,-18,-1, -,-3,-4,-5,-8,-30,-31,-51,-53,-54,-5,-58, -59,-1,-3,-4,-5,-8,-9,-70,-71,-77,-83 Revised 1//9 38

45 ITEM PART NO. DESCRIPTION QTY 3.0 COMPRESSOR MOUNTING AND RELATED COMPONENTS Compressor --- Refer to Section NT40-94 Stiffener Assembly 1 NS U Washer, Flat, # SST NS U Screw, Hex Head, #10-4 x 3/4 lg --- SST (NSI) Used to mount NS Washer, Mylar, 0.05 ID x 0.00 OD Stiffener Assembly 3 9NT40-91 Bracket Assembly, Gauge (NSI) Gauge, Suction Pressure (See Model Chart) Gauge, Discharge Pressure (See Model Chart) 1 U Screw, Pan Head, #-3 x 7/1 lg --- SST (NSI) 7 CA1JA051 Tee, 1/4 npt (NSI) Elbow, 90 Street, 1/4 mpt x 1/4 mpt --- Brass 1 9 0DA Valve Assembly, Core, Check (Schrader Valve) --- Brass Snubber Assembly Switch, High Pressure (HPS) 1 11 U1-94- Switch, High Pressure (HPS) 9NT ,-75,-78 1 NS Connector, Male, Pin (Used with HPS) (NSI) 1 NS Seal, Cable (Used with HPS) (NSI) 1 1 9NT Tube Assembly, Low Pressure NT Tube Assembly, High Pressure Plug, Pipe, 1/4-18 nptf --- Brass Transducer, Pressure 9NT , NT35-13 Protector (Compressor to Compressor Base) 1 17 AU11JR41 Washer, Lock, 3/8 --- SST 18 AA0JA3 Capscrew, Hex Head, 3/8-1 x 1-1/4 lg --- SST (NSI) Washer, Flat, 3/8 --- SST (NSI) Washer, Mylar, ID x 1.00 OD 1 9NT Base, Compressor 1 NS U Bolt, Hex Head, 3/8-1 x 1.00 lg --- SST (NSI) 7 NS U Washer, Flat, 3/8 --- SST (NSI) Used to mount 7 NS AU11JR41 Washer, Lock, 3/8 --- SST Compressor Base 7 NS Washer, Mylar, ID x 1.00 OD to unit frame Capscrew, 7/1-14 x -3/4 lg --- SST (NSI) Locknut, 7/ SST (NSI) 4 U1-531 Washer, Flat, 7/1 --- SST Washer, Mylar, ID x 0.9 OD (NSI) Washer, Mylar, ID x 1.15 OD 7 9NT Panel, Guard (NSI) 9NT40-489,-1,-,-4,-,-7,-8,-11,-1,-13,-1,-17,-19,-3, -5,-,-9,-30,-31,-50,-5,-0,-1,-,-4,-,-7,-70,-71,-75,-78, U Screw, Hex Head, 1/4-0 x 3/4 lg --- SST (NSI) 1 9 U Washer, Flat, 1/4 --- SST Washer, Mylar, 1/4 ID x 3/4 OD 9 31 U Capscrew, Hex Head, 1/4-0 x 1-1/ lg --- SST (NSI) Locknut, 1/ SST (NSI) NT Guard, Compressor NT35-87 Guard, Compressor 9NT *,-5* NT Guard, Compressor 9NT **,-5**,-,-7,-8,-11,-1,-13,-14,-15, -17,-18,-19,-1,-,-3,-5,-9,-30,-31,-50,-51,-5,-54,-5,-58,59,-0,-1, -,-3,-4,-5,-,-7,-8,-9,-70,-71,-75,-77,-79,-80,-81,-83, U Screw, Hex Head, 5/1-18 x 1 lg --- SST (NSI) 1 35 U Washer, Flat, 5/1 --- SST Washer, Mylar, ID x 1.00 OD NT Bracket, Heater (Optional) (NSI) Screw, Hex Head, 1/4-0 x 0.88 lg --- SST (NSI) Washer, Mylar, 0.5 ID x 0.75 OD Washer, Flat, 1/4 x 0.05 Thk Locknut, 1/4-0 (NSI) Clamp, Cushion, 0.50 OD Washer, Mylar, 0.5 ID x 1.00 OD Screw, Thd Cut, #10-4 x 3/8 lg --- SST (NSI) 1 NS Oil, Compressor (Quart) A/R * PRIOR TO SERIAL NUMBER ** STARTING WITH SERIAL NUMBER