ENGINE REMOVAL Honda Accord EX. Special Tools Required
|
|
- Judith Ford
- 5 years ago
- Views:
Transcription
1 ENGINE REMOVAL Special Tools Required 2008 V6 Attachment Arm SIL02C000033* Engine Support Hanger, A and Reds AAR-T1256* Engine Hanger Balance Bar VSB02C000019* Subframe Adapter VSB02C000016* *Available through the Honda Tool and Equipment Program, NOTE: Use fender covers to avoid damaging painted surfaces. To avoid damaging the wiring and terminals, unplug the wiring connectors carefully while holding the connector portion. Mark all wiring and hoses to avoid misconnection. Also, be sure that they do not contact other wiring or hoses, or interfere with other parts. 1. Remove the both sides hood support strut, then use it as shown in illustration to prop the hood in the wide-open position. Fig. 2: Identifying Sides Hood Support Strut 2. Remove the strut brace (see FRAME BRACE REPLACEMENT ). 3. Drain the power steering fluid (see FLUID CHECK/REPLACEMENT ). 4. Relieve the fuel pressure (see FUEL PRESSURE RELIEVING ). 5. Remove the engine cover (see step 2 under INTAKE MANIFOLD REMOVAL AND INSTALLATION ). 6. Do the battery removal procedure (see BATTERY REMOVAL AND INSTALLATION ). 7. Remove the splash separator (see step 2 under RADIATOR REPLACEMENT ). 8. Remove the front grille cover:
2 2-door (see FRONT GRILLE COVER REPLACEMENT ) 4-door (see FRONT GRILLE COVER REPLACEMENT ) 9. Remove the air cleaner (see AIR CLEANER REMOVAL/INSTALLATION ). 10. Remove the harness clamp (A), the bolts (B), and loosen the bolts (C), then remove the battery base (D). Fig. 3: Identifying Harness Clamp, Bolts And Battery Base 11. Disconnect the battery cables (A) from the under-hood fuse/relay box. Fig. 4: Identifying Battery Cables 12. Remove the ECM/PCM cover (A), then remove the three bolts (B) securing the ECM/PCM.
3 Fig. 5: Identifying ECM/PCM Cover And Bolts 13. Disconnect the ECM/PCM connectors (A) and the engine wire harness connector (B), then remove the harness clamps (C) and the bracket (D). Fig. 6: Identifying ECM/PCM Connectors, Engine Wire Harness Connector, Harness Clamps And Bracket 14. M/T model: Disconnect the engine wire harness connector (E). 15. Disconnect the EVAP canister hose (A) and the brake booster vacuum hose (B).
4 Fig. 7: Identifying EVAP Canister Hose And Brake Booster Vacuum Hose 16. Remove the quick-connect fitting cover (A), then disconnect the fuel feed hose (B) (see FUEL LINE/QUICK-CONNECT FITTING REMOVAL ). Fig. 8: Identifying Quick-Connect Fitting Cover And Fuel Feed Hose 17. Remove the drive belt: '08-10 models J35Z2 engine (see EXCEPT '08-10 MODELS J35Z2 ENGINE ) Except '08-10 models J35Z2 engine (see EXCEPT '08-10 MODELS J35Z2 ENGINE ) 18. Disconnect the power steering pump outlet hose (A) and the power steering pump inlet line (B) from the power steering pump and remove the power steering hose bracket (C), then plug the power steering hoses and the power steering pump.
5 Fig. 9: Identifying Power Steering Pump Outlet Hose And Power Steering Pump Inlet Line 19. Remove the steering wheel (see STEERING WHEEL REMOVAL ). 20. Remove the steering joint cover (A). Fig. 10: Identifying Steering Joint Cover, Steering Joint, Steering Gearbox Pinion Shaft And Steering Joint Bolt 21. Make a reference mark (B) across the steering joint (C) and the steering gearbox pinion shaft (D). Remove the steering joint bolt (E), and loosen the steering joint bolt (F), then disconnect the steering joint from the steering gearbox pinion shaft. 22. M/T model: Remove the three bolts securing the shift cable holder, then remove the shift cable and the select cable (see step 15 under TRANSMISSION REMOVAL ). Do not bend the cables excessively. 23. M/T model: Remove the clutch slave cylinder and the clutch line bracket mounting nut (see step 16 under TRANSMISSION REMOVAL ). Do not operate the clutch pedal once the slave cylinder has been removed. 24. A/T model: Remove the shift cable (see SHIFT CABLE REPLACEMENT ). Do not bend the shift cable excessively. 25. Wait until the engine is cold, then carefully remove the radiator cap. 26. Raise the vehicle on the lift. ServiceRepairManual
Engine Removal/lnstaIlation
Engine Removal/lnstaIlation Removal Make sure jacks and safety stands are placed properly and hoist brackets are attached to the correct positions on the engine. Make sure the vehicle will not roll off
More information2004 Honda ELEMENT. Submodel: Engine Type: L4 Liters: 2.4 Fuel Delivery: FI Fuel: GAS. Engine Installation. Special Tools Required
2004 Honda ELEMENT Submodel: Engine Type: L4 Liters: 2.4 Fuel Delivery: FI Fuel: GAS Engine Installation Special Tools Required Engine hanger/adapter VSB02C000015 Engine support hanger, A & Reds AAR-T-12566
More information2005 Honda ACCORD. Submodel: EX Engine Type: V6 Liters: 3.0 Fuel Delivery: FI Fuel: GAS. Automatic Transmission Installation. Special Tools Required
2005 Honda ACCORD Submodel: EX Engine Type: V6 Liters: 3.0 Fuel Delivery: FI Fuel: GAS Automatic Transmission Installation Special Tools Required Engine support hanger, A and Reds AAR-T-12566 Engine hanger
More informationService Bulletin MIL Comes On With DTCs P0300 Thru P0306 (Supersedes , dated June 5, 2013; see REVISION SUMMARY) August 23, 2013
Service Bulletin 13-024 Applies To: 2013 MDX From VIN 2HNYD2...DH500001 thru 2HNYD2...DH525406 2013 TL SH-AWD From VIN 19UUA9...DA000001 thru 19UUA9...DA005530 2013 ZDX From VIN 2YNYB1...DH500001 thru
More informationCylinder Head Removal
2006 Odyssey Cylinder Head Removal Report a problem with this article NOTE: Use fender covers to avoid damaging painted surfaces. To avoid damaging the wires and terminals, unplug the wiring connectors
More information2003 ACCORD - Intake Manifold Removal and Installation
2003 ACCORD - Intake Manifold Removal and Installation Exploded View '06-07 Models Removal ('03-05 Models) 1. Disconnect the intake air temperature (IAT) sensor connector (A). 2. Remove the vacuum hose
More informationEngine Removal/Installation
Engine Removal/Installation Make sure jacks and safety stands are placed properly and hoist brackets are attached to correct positions on the engine. (See Section 1). Apply parking brake and block rear
More informationService Bulletin TSX: Sticking Rings Resulting in Unusually High Engine Oil Consumption
Applies To: 2009 10 TSX L4 with M/T ALL Service Bulletin 13-006 February 22, 2013 2009 10 TSX: Sticking Rings Resulting in Unusually High Engine Oil Consumption SYMPTOM The engine oil level is low on the
More informationService Bulletin
Service Bulletin 12-087 Applies To: See VEHICLES AFFECTED August 17, 2013 2008 11 Accord L4: Sticking Rings Resulting in Unusually High Engine Oil Consumption (Supersedes 12-087, dated April 30, 2013,
More informationCOMPONENT LOCATION INDEX
DTC TROUBLESHOOTING COMPONENT LOCATION INDEX 2007-08 ENGINE PERFORMANCE Idle Control System - Element Fig. 1: Identifying Idle Control System Component Location DTC P0506: IDLE CONTROL SYSTEM RPM LOWER
More information2013 Kia Optima L4-2.0L Turbo
1 of 13 5/29/2016 11:34 AM 2013 Kia Optima L4-2.0L Turbo Vehicle» Engine, Cooling and Exhaust» Engine» Service and Repair» Removal and Replacement Removal CAUTION: Use fender covers to avoid damaging painted
More informationService Bulletin
Service Bulletin 12-089 Applies To: See VEHICLES AFFECTED April 30, 2013 2010 CR-V: Sticking Rings Resulting in Unusually High Engine Oil Consumption (Supersedes 12-089, dated April 3, 2013, to revise
More information1997 Volvo 850 GLT. Fig. 2: Removing Drive Shaft, Engine Mount Bolt & Torque Arm (5-Cylinder) Courtesy of VOLVO CARS OF NORTH AMERICA.
Fig. 2: Removing Drive Shaft, Engine Mount Bolt & Torque Arm (5-Cylinder) 4. Remove front exhaust pipe nuts and springs. Remove front exhaust pipe bolts. Disconnect speedometer. Remove engine mounting
More informationIntake Manifold Removal and Installation
2004 Element Intake Manifold Removal and Installation Exploded View Removal Report a problem with this article 1. Disconnect the intake air temperature (IAT) sensor connector (A). 2. Remove the vacuum
More information9. Engine Assembly ENGINE ASSEMBLY
9. Engine Assembly A: REMOVAL 1) Set the vehicle on a lift. 2) Open the front hood fully, and then support with the hood stay. 3) Collect the refrigerant from A/C system. 4) Release the fuel pressure.
More informationM-9424-M50B 2012 Boss 302 Intake Manifold INSTALLATION INSTRUCTIONS
!!! PLEASE READ ALL OF THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION. WARNING: CUSTOM CALIBRATION REQUIRED! CALIBRATION NOT INCLUDED! KIT CONTENTS: 1) Intake Manifold Assembly 2) Assembly
More informationService Bulletin
Service Bulletin 12-087 March 31, 2017 06117 Version 6 Warranty Extension: Sticking Rings Resulting in High Engine Oil Consumption Supersedes 12-087, dated April 20, 2016, to revise the information highlighted
More informationZoom and Print Options
Vehicle» Engine, Cooling and Exhaust» Engine» Service and Repair» Removal and Replacement» Engine Replacement Engine Replacement ^ Tools Required - J 38185 Hose Clamp Pliers Removal Procedure 1. Remove
More informationService Bulletin 1988 PRELUDE. RECALL: 1988 Prelude Power Steering Supply Hose
Service Bulletin Model Applicable To File Under Bulletin No. 1988 PRELUDE See VEHICLES AFFECTED ENGINE 88-014 Issue Date APRIL 20, 1988 RECALL: 1988 Prelude Power Steering Supply Hose PROBLEM When subjected
More informationTorque Specifications for 2003 Hyundai Tiburon (GK) 2.7L DOHC
Torque Specifications for 2003 Hyundai Tiburon (GK) 2.7L DOHC Engine Mechanical System Camshaft sprocket bolt 90 ~ 110 900 ~ 1,100 65 ~ 80 Cylinder head cover bolt 8 ~ 10 80 ~ 100 5.8 ~ 7.2 Main bearing
More informationALLDATA Online Chevy Truck S10/T10 P/U 2WD L4-2.2L VIN 4 - Service and... Page 1 of 12. Service and Repair
ALLDATA Online - 2000 Chevy Truck S10/T10 P/U 2WD L4-2.2L VIN 4 - Service and... Page 1 of 12 Home Account Contact ALLDATA Log Out Help PAUL REDEHOFT Select Vehicle New TSBs Technician's Reference Component
More informationWARNING: ALWAYS relieve fuel pressure before disconnecting any fuel related component. DO NOT allow fuel to contact engine or electrical components.
4.0L V8 - VINS [K,U] Selected Block 1990 Lexus LS 400 For Lextreme Powertrain 2020 S. Hacienda Blvd. # D Hacienda Heights California 91745 Copyright 1998 Mitchell Repair Information Company, LLC Friday,
More informationService Bulletin
Service Bulletin 13-082 May 18, 2015 51869-02164 Version 7 Warranty Extension: MIL Comes On With DTCs P0301 thru P0304 Supersedes 13-082, dated September 12, 2015, to revise the information highlighted
More informationService Bulletin
Service Bulletin 13-006 April 16, 2016 49236-01602 Version 6 Warranty Extension: Sticking Rings Resulting in High Engine Oil Consumption Supersedes 13-006, Sticking Rings Resulting in Unusually High Engine
More informationENGINE ASSEMBLY. COMPONENTS (Part 1)
1 of 32 ENGINE ASSEMBLY COMPONENTS (Part 1) 2 of 32 COMPONENTS (Part 2) 3 of 32 COMPONENTS (Part 3) 4 of 32 COMPONENTS (Part 4) 5 of 32 COMPONENTS (Part 5) 6 of 32 COMPONENTS (Part 6) 7 of 32 COMPONENTS
More information1. With the vehicle in NEUTRAL, position it on a hoist. For additional information, refer to Section
SECTION 303-01C: Engine 5.4L (4V) 2009 Mustang Workshop Manual REMOVAL Procedure revision date: 07/25/2008 Engine Special Tool(s) Heavy Duty Floor Crane 014-00071 or equivalent Lifting Bracket, Engine
More informationINTAKE MANIFOLD COLLECTOR. 1. Electric throttle control actuator 2. Gasket 3. Vacuum hose
INTAKE MANIFOLD COLLECTOR Removal and Installation PFP:14003 ABS0095V 1. Electric throttle control actuator 2. Gasket 3. Vacuum hose 4. EVAP canister purge volume control solenoid valve 5. Bracket 6. Intake
More information7. Remove the starter motor. Refer to Starter Motor Replacement (2.2L) or Starter Motor Replacement (4.3L).
1 of 9 1/5/2013 6:40 PM Removal Procedure 1. Disconnect the battery negative cable. Refer to Battery Replacement. 2. Remove the hood. Refer to Hood Replacement. 3. If the vehicle is equipped with a manual
More informationREMOVAL & INSTALLATION
REMOVAL & INSTALLATION NOTE: For reassembly reference, label all electrical connectors, vacuum hoses and fuel lines before removal. Also place mating marks on engine hood and other major assemblies before
More informationSTARTER COMPONENTS FOR REMOVAL AND INSTALLATION
Removal STARTER COMPONENTS FOR REMOVAL AND INSTALLATION Starter Components For Removal And Installation REMOVAL OF STARTER 1. DISCONNECT CABLE FROM NEGATIVE TERMINAL OF BATTERY CAUTION: Work must be started
More information2003 RSX - Intake Manifold Removal and Installation
2003 RSX - Intake Manifold Removal and Installation Exploded View - K20A3 Engine Removal - K20A3 Engine 1. Remove the intake manifold cover. 2. Disconnect the intake air temperature (IAT) sensor connector
More informationService Bulletin
Service Bulletin 13-080 February 03, 2018 08193 Version 7 Warranty Extension: MIL Comes On With DTCs P0301 thru P0304 Supersedes 13-080, dated May 18, 2016, to revise the information highlighted in yellow.
More informationService Bulletin
Service Bulletin 13-081 February 03, 2018 08191 Version 13 Warranty Extension: MIL Comes On With DTCs P0301 thru P0304 Supersedes 13-081, dated January 23, 2018, to revise the information highlighted in
More informationAudi > B4 > Liter V6 2V Engine Mechanical, Engine Code(s): AAH, AFC 10 Engine Assembly
Audi > B4 > 1993 1995 2.8 Liter V6 2V Engine Mechanical, Engine Code(s): AAH, AFC 10 Engine Assembly Removing The engine is removed from above, after being separated from the transmission. Note: All tie
More informationJeep Wrangler 4.0 Liter TJ Jeep Wrangler 2.5 Liter TJ Installation instructions
TM www.jeepair.com 1999 Jeep Wrangler 4.0 Liter TJ 1999-2001 Jeep Wrangler 2.5 Liter TJ Installation instructions Kit Information After 1994 every vehicle was designed for R134a refrigerant. The Jeep kit
More informationService Bulletin. Safety Recall: TL Power Steering Feed Hose Leak (Supersedes , dated June 27, 2012; see REVISION SUMMARY)
Service Bulletin Applies To: 2007 08 TL Check the in VIN status for eligibility 12-020 August 10, 2012 Safety Recall: 2007 08 TL Power Steering Feed Hose Leak (Supersedes 12-020, dated June 27, 2012; see
More informationLower Intake Manifold Replacement
Lower Intake Manifold Replacement Removal Procedure 1. Turn OFF all the lamps and the accessories. 2. Ensure the ignition switch is in the OFF position. 3. Disconnect the negative battery cable from the
More informationDisconnect negative battery cable and remove coolant bottle cap.
1 of 16 3/25/2012 10:18 AM ools Required SA9105E 3-Bar Engine Support Fixture SA9412G Constant Force Clamp Pliers SA9127E Gage Bar Set Powertrain Assembly Removal Caution: Do not allow smoking or the use
More information2013 Mustang Workshop Manual
32. Attach the wiring harness retainers to the LH side of the oil pan and the front oil pan stud bolts and install the 2 nuts. Tighten to 8 Nm (71 lb-in). 33. Position the underbody shield and install
More informationEngine, removing and installing
Стр 1 из 16 10-1 Engine, removing and installing Special tools, testers and auxiliary items required Torque wrench VAG 1331 Torque wrench VAG 1332 Engine/transmission jack VAG 1383 A Spring type clip pliers
More information1 of 12 10/5/2015 8:11 AM
1 of 12 10/5/2015 8:11 AM REMOVAL 1. Perform the fuel pressure release procedure See: Fuel Pressure Release > Procedures > Fuel System Pressure Release Procedure. 2. Recover the refrigerant from the refrigerant
More informationSUMMARY TOOL INFORMATION
Applies To: See VEHICLES AFFECTED Service Bulletin 09-010 October 21, 2011 Engine Rattles at Cold Start-Up (Supersedes 09-010, dated August 17, 2010, to revise the information marked by the black bars)
More informationM-9424-M50CJ INTAKE MANIFOLD INSTALLATION INSTRUCTIONS
Please visit www.fordracingparts.com for the most current instruction information!!! PLEASE READ ALL OF THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION. AT ANY TIME YOU DO NOT UNDERSTAND THE
More information05-08 GT. Hellion Power Systems Mustang Kit Instructions
Hellion Power Systems 05-08 Mustang Kit Instructions 1. Disconnect Battery 2. Drain Radiator, keep fluid for re-installation. 3. Remove air box and inlethoses. 6. Next, underneath, punch oil pan for turbo
More informationProcharger Stage II Intercooled Supercharger System (11-14 GT)
Procharger Stage II Intercooled Supercharger System (11-14 GT) Installation Time: Approximately one day. Installed on 2012 Mustang GT 5.0/Manual Required Tools 3/8 Socket Set (Standard and Metric) 1/2
More informationJeep Wrangler TJ. Complete Air Conditioning System. Slide Control Head. Installation instructions
WWW.JEEPAIR.COM 1996-1998 Jeep Wrangler TJ Complete Air Conditioning System Slide Control Head Installation instructions Kit Information After 1994 every vehicle was designed for R134a refrigerant. The
More informationPage 1 of 6 Section 303-01A: Basic Engine 4.2L REMOVAL 1997 F-150/250 Workshop Manual Engine Special Service Tool(s) Engine Lifting Bracket or equivalent 014-00730 Removal 1. Remove the hood. 2. On A/C
More informationINSTALLATION INSTRUCTIONS FOR MOUNTING
INSTALLATION INSTRUCTIONS FOR MOUNTING FRONT PARKING SENSOR RELOCATION BRACKETS ON THE FOLLOWING PROWLER MAX MODEL NOS.: 320713/321610, 310713/321610, 320713/321512 & 310713/321512 ON: (NOTE: TWO 390210
More informationCLUTCH Toyota Celica DESCRIPTION ADJUSTMENTS CLUTCH PEDAL HEIGHT Clutch. Celica
CLUTCH 1993 Toyota Celica 1993 Clutch Celica DESCRIPTION The single, dry disc type clutch uses a hydraulically operated master cylinder and a release cylinder mounted on clutch housing. Clutch release
More information10/30/2018 Intake Manifold Replacement (RPOs LY2/LY6) 2007 GMC Truck Yukon Denali MotoLogic
2007 Yukon Denali Applies to: 4.8L, 5.3L, 6.0L and 6.2L Report a problem with this article Removal Procedure 1. Remove the air cleaner outlet duct. Refer to Air Cleaner Resonator Outlet Duct Replacement.
More informationREMOVAL AND INSTALLATION OF TRANSAXLE (4WD)
MT63 REMOVAL AND INSTALLATION OF TRANSAXLE (4WD) REMOVAL AND INSTALLATION OF TRANSAXLE REMOVE AND INSTALL TRANSAXLE AS SHOWN MT64 REMOVAL OF TRANSAXLE 1. DISCONNECT CABLE FROM NEGATIVE TERMINAL OF BATTERY
More informationHuron Speed Products Twin Turbo Install Gen 2 CTS-V (09-15)
Huron Speed Products Twin Turbo Install Gen 2 CTS-V (09-15) 1 2 Remove two bolts in trunk cover with 8mm socket. Pull up on cover to remove. Unscrew net tie down on side cover where battery is located
More informationREMOVAL 1. DRAIN ENGINE COOLANT 2. REMOVE THROTTLE BODY COVER 3. DISCONNECT TIMING BELT FROM CAMSHAFT TIM- ING PULLEYS (See page EM 14)
EM34 ENGINE MECHANICAL (2UZFE) EM11U02 REMOVAL 1. DRAIN ENGINE COOLANT 2. REMOVE THROTTLE BODY COVER 3. DISCONNECT TIMING BELT FROM CAMSHAFT TIM- ING PULLEYS (See page EM14) A02844 Be careful not to drop
More informationREMOVAL. Fig Sized for Print
ALLDATA Online - 2000 Dodge Truck Grand Caravan FWD V6-3.3L VIN R - Intake M... Page 1 of 10 REMOVAL 1. Remove windshield wiper module. 2. Perform fuel system pressure release procedure (before attempting
More informationSuspension. Front Suspension Knuckle/Hub/Wheel Bearing Replacement Upper Arm Replacement Lower Arm Removal/Installation...
Suspension Front and Rear Suspension : Special Tools..18-2 Component Location Index:...18-3. Wheel Alignment.. 18-5 Wheel Bearing End Play Inspection... 18-8 Wheel Runout Inspection... 18-8 Wheel Bolt
More informationINTAKE AND EXHAUST 15-1 CONTENTS SERVICE ADJUSTMENT PROCEDURES... 2 EXHAUST MANIFOLD EXHAUST PIPE AND MAIN MUFFLER...
I i 15-1 INTAKE AND EXHAUST CONTENTS 110003071 L AIR CLEANER 4.5L Engine>....3 AIR CLEANER 4.8L Engine>....4 EXHAUST MANIFOLD... 10 EXHAUST PIPE AND MAIN MUFFLER... 13 GENERAL INFORMATION.... 2 INTAKE
More information1983 BMW 320i. 1.8L 4-CYL 1983 Engines - 1.8L 4-Cylinder Engines - 1.8L 4-Cylinder
ENGINE IDENTIFICATION 1.8L 4-CYL 1983 Engines - 1.8L 4-Cylinder For engine repair procedures not covered in this article, see ENGINE OVERHAUL PROCEDURES - GENERAL INFORMATION article in the GENERAL INFORMATION
More informationJeep Wrangler TJ 4.0 LITER Installation instructions
www.jeepair.com 2002-2004 Jeep Wrangler TJ 4.0 LITER Installation instructions Kit Information These directions are for 2002-2006 model Jeep Wranglers. After 1994 every vehicle was designed for R134a refrigerant.
More information1. Remove the battery tray. For additional information, refer to Battery Tray ( )
Page 1 of 11 Removal 1. Remove the battery tray. For additional information, refer to Battery Tray (86.15.11) 2. Remove the air cleaner. For additional information, refer to Air Cleaner (19.10.05) 3. NOTE
More informationEM 92 2TR-FE ENGINE MECHANICAL ENGINE ASSEMBLY REMOVAL
92 2TR-FE ENGINE MECHANICAL ENGINE ASSBLY ROVAL 1. ROVE HOOD SUB-ASSBLY 2. DISCHARGE FUEL SYST PRESSURE ( FU-1) 3. ROVE NO. 1 ENGINE UNDER COVER SUB- ASSBLY (for Pre Runner and 4WD Type) (a) Remove the
More informationCOLD AIR SYSTEM. Installation Instructions for: Part Number Civic CX/DX/LX
COLD AIR SYSTEM Installation Instructions for: Part Number 21-413 1996-2000 Civic CX/DX/LX ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit A Hawthorne, CA. 90250 Phone: (310) 484-2322 Fax: (310)
More informationTransmission, removing and
Page 1 of 20 34-18 Transmission, removing and installing Removing Special tools and equipment 3282 transmission support 3282/10 adjustment plate 3337 ring spanner 7-piece set VAG1383A engine/transmission
More informationINSTALLATION INSTRUCTIONS ELEVATION FRONT BUMPER DODGE RAM
INSTALLATION INSTRUCTIONS PARTS LIST: 1 Elevation Bumper Assembly 24 12mm x 37mm OD x 3mm Flat Washers 2 Frame Mounting Brackets 12 12mm Nylon Lock Nuts 8 12-1.75mm x 50mm Hex Bolts 2 License Plate Mounting
More informationIntake Manifold Removal
PLEASE READ ALL OF THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION. AT ANY TIME YOU DO NOT UNDERSTAND THE INSTRUCTIONS Parts included: -GT350 Intake manifold M-944-M5 -GT350 Air bucket w/filter.
More informationELECTRICAL COMPONENT LOCATOR
ELECTRICAL COMPONENT LOCATOR 1988 Toyota Celica 1988 TOYOTA Celica Electrical Components ---------------------------------------------------------------------- BUZZERS, RELAYS & TIMERS ----------------------------------------------------------------------
More informationDrawing Page Drawing Page
Contents Drawing Page Drawing Page L4 Engine...1 L4 Engine - Exploded View...2 V6 Engine...3 V6 Engine - Exploded View... 4 Oil Filter...5 VTEC (Variable Timing Electronic Control) System... 6 Fuel and
More information303-01C Engine 3.5L 2010 Fusion, Milan, MKZ, Fusion Hybrid, Milan Hybrid. REMOVAL Procedure revision date: 10/19/2012. Engine
2010 MKZ Report a problem with this article 303-01C Engine 3.5L 2010 Fusion, Milan, MKZ, Fusion Hybrid, Milan Hybrid REMOVAL Procedure revision date: 10/19/2012 Engine Special Tool(s) 2,200# Floor Crane,
More informationDisconnect the breather tube from the air cleaner outlet duct.
Disconnect the breather tube from the air cleaner outlet duct. Disconnect the IAT sensor harness connector. Remove the air cleaner outlet duct retaining wingnut. Separate the air cleaner outlet duct from
More informationPARTIAL ENGINE ASSY COMPONENTS. Clip. Radiator Grille. Clip. Front Bumper Cover. Engine Under Cover LH. N m (kgf cm, ft lbf) : Specified torque
ENGINE MECHANICAL 1417 COMPONENTS 141FP01 Radiator Grille Front Bumper Cover Engine Under Cover RH Engine Under Cover LH A79361 962 1418 ENGINE MECHANICAL Heater Outlet Water Hose 7.0 (71, 62 in. lbf)
More informationFastener Tightening Specifications Specification
2008 G6 Applies to: 3.5L Report a problem with this article Fastener Tightening s A/C Compressor Bracket Bolt Camshaft Position Actuator Assembly Bolt 16 Y 12 lb ft Camshaft Position Actuator Magnet Bolt
More informationCylinder Head Assembly: Removal and Replacement Repair Procedures
2007 Kia Rio L4-1.6L Copyright 2013, ALLDATA 10.52 Page 1 Cylinder Head Assembly: Removal and Replacement Repair Procedures COMPONENT 2007 Kia Rio L4-1.6L Copyright 2013, ALLDATA 10.52 Page 2 REMOVAL Engine
More informationARTICLE BEGINNING * PLEASE READ THIS FIRST * DESCRIPTION OPERATION ATC COMPUTER BLEND-AIR DOOR ACTUATOR CONTROL PANEL
A/C-HEATER SYSTEM - AUTOMATIC Article Text 1989 Chrysler LeBaron Sedan For m m m m m Copyright 1998 Mitchell Repair Information Company, LLC Thursday, July 03, 2003 10:15AM ARTICLE BEGINNING 1989 AUTOMATIC
More informationDESCRIPTION & OPERATION
2004 BRAKES Disc - TSX DESCRIPTION & OPERATION WARNING: DO NOT use air pressure or a dry brush to clean brake assemblies. Avoid breathing brake dust. Use OSHA-approved vacuum cleaner for cleaning and collecting
More information2000 Chrysler SEBRING
2000 Chrysler SEBRING Submodel: JX Engine Type: V6 Liters: 2.5 Fuel Delivery: FI Fuel: GAS 2.0L SOHC and 2.4L DOHC Engines The intake manifold for the 2.0L SOHC engine is a long branch design made of a
More information2015+ SUBARU STI FRONT-MOUNT INTERCOOLER PARTS LIST AND INSTALLATION GUIDE INSTALL DIFFICULTY DISCLAIMER CAUTION INSTALL PROCEDURE TOOLS NEEDED
PARTS LIST AND PARTS INCLUDED 1PC ALUMINUM INTAKE PIPE 1PC BAR-AND-PLATE INTERCOOLER 1PC STEEL CRASH BAR W/ MOUNTING HARDWARE 2PC HOT-SIDE INTERCOOLER PIPES 2PC COLD-SIDE INTERCOOLER PIPES 1PC BPV FLANGE
More informationREMOVAL. 10. REMOVE FRONT SUSPENSION MEMBER BRACE Remove the 8 bolts and brace.
EM64 ENGINE MECHANICAL (2JZGE) EM1S801 REMOVAL 1. REMOVE ENGINE UNDER COVER 2. DRAIN ENGINE COOLANT 3. DRAIN ENGINE OIL 4. REMOVE ENGINE COVER Remove the 4 nuts and engine cover. 5. REMOVE AIR CLEANER
More informationfile://c:\program Files\tsocache\OFFICE_5164\SYA~us~en~file=SYA1C003.htm~gen~re...
Page 1 of 26 SECTION 501-12: Instrument Panel and Console 2000 Crown Victoria/Grand Marquis Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 06/21/1999 Instrument Panel Removal CAUTION:
More informationJeep Wrangler TJ 4.0 LITER Installation instructions
www.jeepair.com 2000-2001 Jeep Wrangler TJ 4.0 LITER Installation instructions Important information about your system, and warranty DO NOT ADD ANY OIL TO ANY PART OF THE SYSTEM. DO NOT USE THE SIGHT GLASS
More informationASSEMBLY/INSTALLATION INSTRUCTIONS
ASSEMBLY/INSTALLATION INSTRUCTIONS AURORA 3000 & 4000 SCORPION TURBO SYSTEM NOTICE: The engine oil must be changed any time the turbocharger is removed from the engine. The passages in the block underneath
More informationINSTALLATION INSTRUCTIONS BILLET FUEL RAIL KIT
INSTALLATION INSTRUCTIONS BILLET FUEL RAIL KIT MITSUBISHI LANCER EVOLUTION X Document# 19-0067 Support: info@radiumauto.com WARNING: DON'T SMOKE OR WORK WITH OPEN SPARKS WHILE WORKING ON THE FUEL SYSTEM
More informationHuron Speed Products Twin Turbo Install Gen 2 CTS-V (09-15)
Huron Speed Products Twin Turbo Install Gen 2 CTS-V (09-15) The following install guide is simply that, a guide to help you with installation. It is by no means the exact method to perform installation,
More informationENGINE COOLING GROUP CONTENTS RADIATOR GENERAL DESCRIPTION SPECIAL TOOLS THERMOSTAT
14-1 GROUP 14 CONTENTS GENERAL DESCRIPTION 14-2 SPECIAL TOOLS 14-3 DIAGNOSIS 14-3 INTRODUCTION 14-3 TROUBLESHOOTING STRATEGY 14-3 SYMPTOM CHART 14-4 SYMPTOM PROCEDURES 14-4 ON-VEHICLE SERVICE 14-17 ENGINE
More information-Magnet (not completely necessary but can come in handy)
McLeod High Performance Hydraulic Clutch Line Upgrade (05-14 V8) Included in kit: -New clutch line -2 fittings Required Tools: -Floor jack and jack stands (or a lift) -Flashlight -Angled pick tool -13mm
More informationBody, front. Lock carrier with attachments, removing and installing
Page 1 of 19 50-1 Body, front Lock carrier with attachments, removing and installing 1 - Hex bolt (6x) 45 Nm (33 ft lb) 2 - Hex bolt 45 Nm (33 ft lb) 3 - Hex bolt (4x) 10 Nm (7 ft lb) 4 - Hex bolts (2x)
More informationThis information covers the proper service procedures for the replacement of the radiator on a chassis with the Volvo D16F engine.
Volvo Trucks North America Greensboro, NC USA This Service Bulletin replaces SB 260-32, Cooling System Service, dated (1.2007), publication no. PV776-20177193. Radiator, Replacement DService Bulletin Trucks
More informationINSTALLATION INSTRUCTIONS
N-MT13-1 & N-MT13-2 COLD AIR INTAKE KIT INSTALLATION INSTRUCTIONS MUSTANG GT 2015-up PARTS INCLUDED Part Number Descrip on Qty 9-SA-INTAKE-100 Intake Assembly 1 9-SA-HEATSHIELD-100 Heatshield Assembly
More informationADJUSTMENTS Mazda MX-3. Fig. 1: Identifying Engine Code & Number Courtesy of MAZDA MOTORS CORP. VALVE CLEARANCE ADJUSTMENT
Fig. 1: Identifying Engine Code & Number Courtesy of MAZDA MOTORS CORP. ADJUSTMENTS VALVE CLEARANCE ADJUSTMENT 1. No valve clearance adjustment is required, as hydraulic valve lash adjusters are used.
More informationCOMPONENT LOCATOR > DISASSEMBLED VIEWS
Page 1 of 45 2006 Pontiac Grand Prix 3.8L Eng Base Service Manual: ENGINE MECHANICAL - 3.8L COMPONENT LOCATOR > DISASSEMBLED VIEWS Fig 1: Engine Block Component Views Callout Component Name 100 Engine
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. AIR CONDITIONER CIVIC 2- AND 4-DOOR AII 24158 Issue Date SEP 2002 What s New The installation instructions for the 2003 Civic A/C are the
More informationInstallation Instructions for TJ Jeep s Fiberglass Replacement Bodies and Parts
Installation Instructions for 1997-2006 TJ Jeep s Fiberglass Replacement Bodies and Parts Getting started: We recommend that you take pictures as you dismantle your Jeep. These pictures will help you when
More information7-0 ENGINE REMOVAL 7. ENGINE REMOVAL/INSTALLATION MXU 500
7 ENGINE REMOVAL SERVICE INFORMATION------------------------------------------------ 7-1 ENGINE REMOVAL ------------------------------------------------------- 7-2 ENGINE INSTALLATION ------------------------------------------------
More informationALLDATA Online Chevy Truck S10/T10 Blazer 2WD V6-4.3L VIN W - Intake... Intake Manifold Replacement (Upper)
ALLDATA Online - 2001 Chevy Truck S10/T10 Blazer 2WD V6-4.3L VIN W - Intake... Page 1 of 21 Home Account Contact ALLDATA Log Out Help PAUL REDEHOFT Select Vehicle New TSBs Technician's Reference Component
More informationR8 Exhaust Installation Guidelines
STāSIS Engineering R8 Exhaust Installation Guidelines Exhaust Muffler support bracket bolt to muffler Muffler support bracket to chassis Muffler heat shield screws Heat shield bolt to chassis beneath anti
More informationThis information covers the proper procedure for replacing the Volvo D16F engine in a VT or VNL chassis.
Volvo Trucks North America Greensboro, NC USA Engine, Replacement DService Bulletin Trucks Date Group No. Page 10.2007 210 139 1(47) Engine, Replacement Volvo D16F VNL, VT W2005773 This information covers
More informationINSTALLATION INSTRUCTIONS PART NUMBER:
Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 21-518B (Blue Finish) 21-518C (Gun Metal Grey Finish) 21-518P (Vacuum Metalized Chrome-VMC) 21-518R (Red Finish)
More informationX-TYPE. Malfunctioning Brake Vacuum Pump Remove Pump Procedure
SERVICE X-TYPE DATE 09/01 TECHNICAL BULLETIN Malfunctioning Brake Vacuum Pump Remove Pump Procedure MODEL VIN XT206-01 2002 MY-ON X-TYPE C00001-ON Issue: This Technical Bulletin has been issued to provide
More informationEGR heater plate removal and installation procedure has been added.
NUMBER: 08 60-3 S.M. REF.: 8.3 ENGINE: EPA07 Series 60 DATE:June 2008 SUBJECT: EGR HEATER PLATE PUBLICATION: DDC-SVC-MAN-0005 EGR heater plate removal and installation procedure has been added. 8.3.1 REMOVAL
More informationM-7512-A Mustang Clutch Fluid Line
Please visit www. performanceparts.ford.com for the most current instruction and warranty information. PLEASE READ ALL OF THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION. AT ANY TIME YOU DO
More information8. ENGINE REMOVAL/INSTALLATION
8. ENGINE REMOVAL/INSTALLATION COMPONENT LOCATION 8-2 SERVICE INFORMATION 8-3 ENGINE REMOVAL 8-4 ENGINE INSTALLATION 8-8 8 8-1 ENGINE REMOVAL/INSTALLATION COMPONENT LOCATION 69 N m (7.0 kgf m, 51 lbf ft)
More informationINTAKE AND EXHAUST GROUP CONTENTS GENERAL INFORMATION SERVICE SPECIFICATION AIR CLEANER
15-1 GROUP 15 INTAKE AND EXHAUST CONTENTS GENERAL INFORMATION 15-2 SERVICE SPECIFICATION 15-2 DIAGNOSIS 15-2 INTRODUCTION 15-2 TROUBLESHOOTING STRATEGY 15-2 SYMPTOM CHART 15-2 SYMPTOM PROCEDURES 15-3 SPECIAL
More information