EM 92 2TR-FE ENGINE MECHANICAL ENGINE ASSEMBLY REMOVAL

Size: px
Start display at page:

Download "EM 92 2TR-FE ENGINE MECHANICAL ENGINE ASSEMBLY REMOVAL"

Transcription

1 92 2TR-FE ENGINE MECHANICAL ENGINE ASSBLY ROVAL 1. ROVE HOOD SUB-ASSBLY 2. DISCHARGE FUEL SYST PRESSURE ( FU-1) 3. ROVE NO. 1 ENGINE UNDER COVER SUB- ASSBLY (for Pre Runner and 4WD Type) (a) Remove the 4bolts, then remove the engine under cover No ROVE NO. 2 ENGINE UNDER COVER SUB- ASSBLY (for Pre Runner and 4WD Type, Regular Cab) (a) Remove the 4 bolts, then remove engine cover No DRAIN ENGINE COOLANT ( CO-3) 6. ROVE BATTERY 7. ROVE BATTERY TRAY 8. ROVE RADIATOR SUPPORT TO FRAME SEAL LH ( CO-12) 9. ROVE FAN SHROUD ( CO-13) 10. ROVE AIR CLEANER CAP SUB-ASSBLY (See page EC-14) 11. ROVE AIR CLEANER FILTER ELENT SUB- ASSBLY 12. ROVE AIR CLEANER CASE (a) Remove the 3 bolts, then remove the air cleaner case. 13. SEPARATE VANE PUMP ( -21) 14. ROVE NO. 2 RADIATOR HOSE 15. SEPARATE COMPRESSOR AND MAGNETIC CLUTCH (w/ Air Conditioning System) ( - 21) 16. ROVE RADIATOR HOSE INLET 17. SEPARATE WATER HOSE SUB-ASSBLY (a) Separate the water hoses. 18. DISCONNECT FUEL HOSE ( FU-11) 19. DISCONNECT NO. 2 FUEL HOSE ( FU-11) G038551E01

2 2TR-FE ENGINE MECHANICAL ENGINE ASSBLY SEPARATE FUEL VAPOR FEED HOSE ASSBLY (a) Disconnect the fuel vapor feed hose. G038552E01 G038553E DISCONNECT NO. 1 AIR INJECTION HOSE (a) Disconnect the No.1 air injection hose. 22. DISCONNECT ENGINE WIRE (a) Disconnect the connector from the ECM, then pull the engine wire harness to the compartment side. Do not forcibly pull the wire harness to the engine compartment side. (b) Disconnect all wire harnesses and connectors in the engine room. 23. ROVE EXHAUST PIPE ASSBLY TAIL ( EX-2) 24. ROVE EXHAUST PIPE ASSBLY FRONT (See page EX-2) 25. ROVE MANUAL TRANSMISSION UNIT ASSBLY F MT-6 MT-8 FR: RR: 26. ROVE AUTOMATIC TRANSMISSION ASSBLY ( AT-113) 27. ROVE ENGINE ASSBLY (a) Install the engine hanger with the bolt. Torque: 42 N*m (420 kgf*cm, 30 ft.*lbf) Part No Part Name Part No. Engine hanger Bolt A1020 G037564E03 Be sure to use the bolts when installing the engine hanger.

3 94 2TR-FE ENGINE MECHANICAL ENGINE ASSBLY G038554E01 (b) Attach the engine sling device and chain block to the engine hangers. (c) Remove the 4 bolts and 4 nuts. (d) Lift the engine out of the vehicle slowly and carefully by operating the engine sling device and chain block. Make sure that no wires, hoses or cables are connected to the engine. 28. ROVE CLUTCH COVER ASSBLY (for Manual ) F CL-30 CL ROVE CLUTCH DISC ASSBLY (for Manual ) F CL-30 CL ROVE FLYWHEEL SUB-ASSBLY (for Manual ) ( -77) 31. ROVE DRIVE PLATE AND RING GEAR SUB- ASSBLY (for Automatic ) ( -78) 32. ROVE REAR END PLATE ( -66) 33. ROVE INTAKE AIR CONNECTOR ( ES- 452) 34. ROVE FUEL HOSE ( FU-11) 35. ROVE NO. 2 FUEL HOSE ( FU-11) 36. ROVE THROTTLE WITH MOTOR BODY ASSBLY ( ES-453) 37. ROVE NO. 1 INTAKE MANIFOLD TO HEAD GASKET ( ES-460) 38. ROVE IDLE PULLEY ASSBLY WITH BRACKET (w/ Air Conditioning System) ( ES-446) 39. ROVE ENGINE WIRE 40. ROVE OIL LEVEL GAGE SUB-ASSBLY

4 2TR-FE ENGINE MECHANICAL ENGINE ASSBLY ROVE OIL LEVEL GAGE GUIDE (a) Remove the bolts, then remove the oil level gage guide. G037556E01 G038555E ROVE FRONT NO. 1 ENGINE MOUNTING BRACKET (a) Remove the 4 bolts, then remove the engine mounting bracket front No. 1 LH with engine mounting insulator front. 43. ROVE THERMOSTAT ( CO-7) 44. ROVE FUEL INJECTOR ASSBLY ( FU-13) 45. ROVE KNOCK SENSOR ( ES-462) 46. ROVE ENGINE COOLANT TPERATURE SENSOR (a) Using a 19 mm deep socket wrench, remove the engine coolant temperature sensor. G037562E ROVE NO. 1 WATER BY-PASS PIPE (a) Remove the 2 nuts, then remove the water by-pass pipe No. 1. G035420E01 G038556E ROVE VENTILATION PIPE (a) Remove the bolts, then remove the ventilation pipe. 49. ROVE IGNITION COIL ASSBLY ( -38) 50. ROVE SPARK PLUG 51. ROVE GENERATOR ASSBLY ( CH-7) 52. ROVE NO. 1 IDLER PULLEY SUB-ASSBLY ( -23)

5 96 2TR-FE ENGINE MECHANICAL ENGINE ASSBLY G038557E ROVE V-RIBBED BELT TENSIONER ASSBLY ( CO-5) 54. ROVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR ( EC-14) 55. ROVE AIR SWITCHING VALVE ASSBLY (See page EC-15) 56. ROVE EXHAUST MANIFOLD ( -67) 57. ROVE FRONT NO. 1 ENGINE MOUNTING BRACKET RH (a) Remove the 4 bolts, then remove the engine mounting bracket front No. 1 together with the engine mounting insulator front. 58. ROVE ENGINE OIL PRESSURE SWITCH ASSBLY ( LU-1)

EM 97 2TR-FE ENGINE MECHANICAL ENGINE ASSEMBLY INSTALLATION

EM 97 2TR-FE ENGINE MECHANICAL ENGINE ASSEMBLY INSTALLATION 2TR-FE ENGINE MECHANICAL ENGINE ASSBLY 97 G038557E01 INSTALLATION 1. INSTALL ENGINE OIL PRESSURE SWITCH ASSBLY ( LU-1) 2. INSTALL FRONT NO. 1 ENGINE MOUNTING BRACKET RH (a) Install the engine mounting

More information

REMOVAL EM SEPARATE COMPRESSOR AND MAGNETIC CLUTCH (w/ Air Conditioning System) (a) Remove the bolt shown in the illustration.

REMOVAL EM SEPARATE COMPRESSOR AND MAGNETIC CLUTCH (w/ Air Conditioning System) (a) Remove the bolt shown in the illustration. 21 ROVAL 1. ROVE HOOD SUB-ASSBLY 2. DISCHARGE FUEL SYST PRESSURE (See page FU-1) 3. ROVE NO. 1 ENGINE UNDER COVER SUB- ASSBLY (for 4WD and Pre-Runner) (a) Remove the 4 bolts, then remove the No. 1 engine

More information

REMOVAL EM SEPARATE COMPRESSOR AND MAGNETIC CLUTCH (w/ Air Conditioning System) (a) Remove the bolt shown in the illustration.

REMOVAL EM SEPARATE COMPRESSOR AND MAGNETIC CLUTCH (w/ Air Conditioning System) (a) Remove the bolt shown in the illustration. 21 ROVAL 1. ROVE HOOD SUB-ASSBLY 2. DISCHARGE FUEL SYST PRESSURE (See page FU-1) 3. ROVE NO. 1 ENGINE UNDER COVER SUB- ASSBLY (for 4WD and Pre-Runner) (a) Remove the 4 bolts, then remove the No. 1 engine

More information

EM 112 1GR-FE ENGINE MECHANICAL ENGINE ASSEMBLY INSPECTION. Intake Air Surge Tank Side

EM 112 1GR-FE ENGINE MECHANICAL ENGINE ASSEMBLY INSPECTION. Intake Air Surge Tank Side 112 Intake Air Surge Tank Side Cylinder Head Side 1GR-FE ENGINE MECHANICAL ENGINE ASSBLY INSPECTION 1. INSPECT INTAKE MANIFOLD FOR WARPAGE (a) Using a precision straight edge and feeler gauge, measure

More information

PARTIAL ENGINE ASSY (2TR FE)

PARTIAL ENGINE ASSY (2TR FE) COMPONENTS 147 1421Z01 Clip Hood Subassy x9 Radiator Support to Frame Seal LH 30 (306, 22) 30 (306, 22) Fan and Generator V Belt 5.0 (51, 44 in. lbf) Fan Shroud Fan Pulley Fan w/ Fluid Coupling PRE RUNNER

More information

CYLINDER HEAD (for Bank 2 4WD and Pre-Runner)

CYLINDER HEAD (for Bank 2 4WD and Pre-Runner) 144 1GR-FE ENGINE MECHANICAL CYLINDER HEAD (for Bank 2 4WD and Pre-Runner) CYLINDER HEAD (for Bank 2 4WD and Pre-Runner) ENGINE 1GR-FE ENGINE MECHANICAL COMPONENTS 88 (897, 65) x4 88 (897, 65) x4 NO. 1

More information

ENGINE ASSEMBLY COMPONENTS EM 170 1GR-FE ENGINE MECHANICAL ENGINE ASSEMBLY V-BANK COVER VACUUM HOSE AIR CLEANER ASSEMBLY NO. 2 VENTILATION HOSE

ENGINE ASSEMBLY COMPONENTS EM 170 1GR-FE ENGINE MECHANICAL ENGINE ASSEMBLY V-BANK COVER VACUUM HOSE AIR CLEANER ASSEMBLY NO. 2 VENTILATION HOSE 170 ENGINE 1GR-FE MECHANICAL COMPONENTS 1GR-FE ENGINE MECHANICAL ENGINE 7.5 (76, 66 in.*lbf) V-BANK COVER 8.0 (82, 71 in.*lbf) 8.0 (82, 71 in.*lbf) VACUUM HOSE AIR CLEANER NO. 2 VENTILATION HOSE MASS AIR

More information

ENGINE ASSEMBLY. COMPONENTS (Part 1)

ENGINE ASSEMBLY. COMPONENTS (Part 1) 1 of 32 ENGINE ASSEMBLY COMPONENTS (Part 1) 2 of 32 COMPONENTS (Part 2) 3 of 32 COMPONENTS (Part 3) 4 of 32 COMPONENTS (Part 4) 5 of 32 COMPONENTS (Part 5) 6 of 32 COMPONENTS (Part 6) 7 of 32 COMPONENTS

More information

OIL PUMP (for 4WD and Pre-Runner)

OIL PUMP (for 4WD and Pre-Runner) 1GR-FE BRICATION OIL PUMP (for 4WD and Pre-Runner) OIL PUMP (for 4WD and Pre-Runner) ENGINE 1GR-FE BRICATION COMPONENTS 23 88 (897, 65) 88 (897, 65) NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY FRONT PROPELLER

More information

PARTIAL ENGINE ASSY (2ZZ GE)

PARTIAL ENGINE ASSY (2ZZ GE) COMPONENTS 14189 140R701 7.0 (71, 62 in. lbf) Cylinder Head Cover No. 2 19 (194, 14) Radiator Support Upper 19 (194, 14) Radiator Hose Inlet Cruise Control Actuator Assy 6.0 (61, 53 in. lbf) Radiator Assy

More information

PARTIAL ENGINE ASSY COMPONENTS. Clip. Radiator Grille. Clip. Front Bumper Cover. Engine Under Cover LH. N m (kgf cm, ft lbf) : Specified torque

PARTIAL ENGINE ASSY COMPONENTS. Clip. Radiator Grille. Clip. Front Bumper Cover. Engine Under Cover LH. N m (kgf cm, ft lbf) : Specified torque ENGINE MECHANICAL 1417 COMPONENTS 141FP01 Radiator Grille Front Bumper Cover Engine Under Cover RH Engine Under Cover LH A79361 962 1418 ENGINE MECHANICAL Heater Outlet Water Hose 7.0 (71, 62 in. lbf)

More information

VALVE CLEARANCE ADJUSTMENT EM 7

VALVE CLEARANCE ADJUSTMENT EM 7 GR-FE ENGE MECHANICAL VALVE CLEARANCE VALVE CLEARANCE ADJUSTMENT 7. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMAL 2. DRA ENGE COOLANT (See page CO-3) 3. ROVE V-BANK COVER (See page ES-44) 4. ROVE AIR CLEANER

More information

1GR-FE ENGINE MECHANICAL: TIMING CHAIN: INSTALLATION (2007 4Runner) Model Year: 2007 Model: 4Runner Doc ID: RM WS002X

1GR-FE ENGINE MECHANICAL: TIMING CHAIN: INSTALLATION (2007 4Runner) Model Year: 2007 Model: 4Runner Doc ID: RM WS002X Last Modified: 4-26-2007 Service Category: Engine/Hybrid System 1.6 A Section: Engine Mechanical Model Year: 2007 Model: 4Runner Doc ID: RM0000029WS002X Title: 1GR-FE ENGINE MECHANICAL: TIMING CHAIN: INSTALLATION

More information

INSTALLATION EM 8 1NZ-FE ENGINE MECHANICAL DRIVE BELT INCORRECT CORRECT. Generator Vehicle Front A077960E03. Adjusting Bar. Bolt A. Bolt B.

INSTALLATION EM 8 1NZ-FE ENGINE MECHANICAL DRIVE BELT INCORRECT CORRECT. Generator Vehicle Front A077960E03. Adjusting Bar. Bolt A. Bolt B. 8 CORRECT Adjusting Bar 1NZ-FE ENGINE MECHANICAL DRIVE BELT INCORRECT Generator Vehicle Front A077960E03 INSTALLATION 1. INSTALL VANE PUMP V BELT (a) Temporarily install the belt on each pulley. 2. INSTALL

More information

VALVE CLEARANCE ADJUSTMENT EM 8

VALVE CLEARANCE ADJUSTMENT EM 8 8 1GR-FE ENGE MECHANICAL VALVE CLEARANCE VALVE CLEARANCE ADJUSTMENT 1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMAL 2. DRA ENGE COOLANT (See page CO-3) 3. ROVE V-BANK COVER (See page ES-428) 4. ROVE AIR

More information

Fastener Tightening Specifications Specification

Fastener Tightening Specifications Specification 2008 G6 Applies to: 3.5L Report a problem with this article Fastener Tightening s A/C Compressor Bracket Bolt Camshaft Position Actuator Assembly Bolt 16 Y 12 lb ft Camshaft Position Actuator Magnet Bolt

More information

REMOVAL AND INSTALLATION OF TRANSAXLE (4WD)

REMOVAL AND INSTALLATION OF TRANSAXLE (4WD) MT63 REMOVAL AND INSTALLATION OF TRANSAXLE (4WD) REMOVAL AND INSTALLATION OF TRANSAXLE REMOVE AND INSTALL TRANSAXLE AS SHOWN MT64 REMOVAL OF TRANSAXLE 1. DISCONNECT CABLE FROM NEGATIVE TERMINAL OF BATTERY

More information

VALVE CLEARANCE (K3-VE)

VALVE CLEARANCE (K3-VE) ENGINE MECHANICAL VALVE CLEARANCE (K3-VE) 25 ENGINE MECHANICAL VALVE CLEARANCE (K3-VE) INSPECTION 1. DISCONNECT NEGATIVE BATTERY TERMINAL (See page RS-164.) 2. ROVE ENGINE UNDER COVER 3. DRAIN ENGINE COOLANT

More information

IG 1 2GR-FE IGNITION IGNITION SYSTEM IGNITION SYSTEM ECM ENGINE ROOM R/B - IG2 FUSE - ST/AM FUSE IGNITION COIL NOISE FILTER NOISE FILTER A137458E01

IG 1 2GR-FE IGNITION IGNITION SYSTEM IGNITION SYSTEM ECM ENGINE ROOM R/B - IG2 FUSE - ST/AM FUSE IGNITION COIL NOISE FILTER NOISE FILTER A137458E01 NITION SYSTEM ENGINE 2GR-FE PARTS LOCATION 2GR-FE NITION NITION SYSTEM 1 ECM ENGINE ROOM R/B - 2 FUSE NITION COIL - ST/AM FUSE NOISE FILTER NOISE FILTER A137458E01 2 2GR-FE NITION NITION SYSTEM SYSTEM

More information

REMOVAL FU 11 2TR-FE FUEL FUEL INJECTOR. Pinch. Checker. Detaching Switch Pull Out. Retainer. Fuel Hose Connector. Pipe. O-ring. Pinch.

REMOVAL FU 11 2TR-FE FUEL FUEL INJECTOR. Pinch. Checker. Detaching Switch Pull Out. Retainer. Fuel Hose Connector. Pipe. O-ring. Pinch. 2TR-FE EL EL INJECTOR 11 REMOVAL 1. DISCHARGE EL SYSTEM PRESSURE (See page -1) 2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL 3. REMOVE ENGINE UNDER COVER SUB-ASSEMBLY NO.1 4. DRAIN ENGINE COOLANT

More information

REMOVAL AC 67. Using a clip remover, disengage the 6 clips and remove the front fender apron seal upper. (2WD)

REMOVAL AC 67. Using a clip remover, disengage the 6 clips and remove the front fender apron seal upper. (2WD) 67 PRE RUNNER 4WD: REMOVAL 1. DISCHARGE REFRIGERANT FROM REFRIGERATION SYSTEM (See page -18) 2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL 3. REMOVE FRONT WHEEL LH 4. REMOVE NO. 1 ENGINE UNDER COVER

More information

Service and Repair. a. Remove the 2 nuts and 2 upper radiator support. b. Lift out the radiator and cooling fan assembly.

Service and Repair. a. Remove the 2 nuts and 2 upper radiator support. b. Lift out the radiator and cooling fan assembly. Service and Repair REPLACEMENT 1. SEPARATE BATTERY NEGATIVE TERMINAL 2. REMOVE AIR CLEANER INLET NO.1 3. DRAIN ENGINE COOLANT 4. REMOVE V-BANK COVER 5. REMOVE INTAKE AIR CONNECTOR PIPE 6. REMOVE ENGINE

More information

FUEL SYSTEM PRECAUTION FU 1

FUEL SYSTEM PRECAUTION FU 1 2GR-FE EL EL SYSTEM EL SYSTEM PRECAUTION 1 1. EXPRESSIONS OF IGNITION SWITCH (a) The type of the ignition switch used on this model differs according to the specifications of the vehicle. The expressions

More information

2/18/2017 Cylinder Head Assembly Service and Repair, Removal and Replacement: Cylinder Head

2/18/2017 Cylinder Head Assembly Service and Repair, Removal and Replacement: Cylinder Head Cylinder Head http://repair.alldata.com/alldata/article/display.action?componentid=65&itypeid=401&nonstandardid=2762152&vehicleid=47645&miles=&printfriendl 1/17 RH Splash Shield Accessory Drive Belt, Thermostat

More information

ON-VEHICLE INSPECTION

ON-VEHICLE INSPECTION 452 DLC3 CAN VIM Intelligent Tester G035612E02 ON-VEHICLE INSPECTION 1. INSPECT THROTTLE BODY (a) Listen to the throttle control motor operating sounds. (1) Turn the ignition switch to ON. (2) When pressing

More information

3/13/ :32 AM. NOTICE: Do not disconnect the hose.

3/13/ :32 AM. NOTICE: Do not disconnect the hose. 1 of 25 REPLACEMENT 1. REMOVE HOOD SUB-ASSEMBLY 2. REMOVE FRONT WHEEL RH 3. REMOVE ENGINE UNDER COVER LH 4. REMOVE ENGINE UNDER COVER RH 5. REMOVE FRONT FENDER APRON SEAL RH 6. DRAIN ENGINE OIL a. Install

More information

1997 Volvo 850 GLT. Fig. 2: Removing Drive Shaft, Engine Mount Bolt & Torque Arm (5-Cylinder) Courtesy of VOLVO CARS OF NORTH AMERICA.

1997 Volvo 850 GLT. Fig. 2: Removing Drive Shaft, Engine Mount Bolt & Torque Arm (5-Cylinder) Courtesy of VOLVO CARS OF NORTH AMERICA. Fig. 2: Removing Drive Shaft, Engine Mount Bolt & Torque Arm (5-Cylinder) 4. Remove front exhaust pipe nuts and springs. Remove front exhaust pipe bolts. Disconnect speedometer. Remove engine mounting

More information

Page 1 of 6 Section 303-01A: Basic Engine 4.2L REMOVAL 1997 F-150/250 Workshop Manual Engine Special Service Tool(s) Engine Lifting Bracket or equivalent 014-00730 Removal 1. Remove the hood. 2. On A/C

More information

2003 Nissan-Datsun Truck Frontier 4WD V6-3.3L (VG33E)

2003 Nissan-Datsun Truck Frontier 4WD V6-3.3L (VG33E) 1 of 15 8/7/2016 2:34 PM 2003 Nissan-Datsun Truck Frontier 4WD V6-3.3L (VG33E) Vehicle» Engine, Cooling and Exhaust» Engine» Cylinder Head Assembly» Service and Repair» Removal and Installation 2 of 15

More information

Zoom and Print Options

Zoom and Print Options Vehicle» Engine, Cooling and Exhaust» Engine» Service and Repair» Removal and Replacement» Engine Replacement Engine Replacement ^ Tools Required - J 38185 Hose Clamp Pliers Removal Procedure 1. Remove

More information

TIMING CHAIN COMPONENTS

TIMING CHAIN COMPONENTS Page 1 of 30 TIMING CHAIN COMPONENTS Fig. 46: Identifying Camshaft Timing Oil Control Valve Assembly Components With Torque Page 2 of 30 Specifications (1 Of 3) Fig. 47: Identifying Camshaft Timing Oil

More information

REMOVAL 1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL 2. REMOVE FRONT WHEEL RH. 3. REMOVE REAR WHEEL (for 4WD) (a) Move the select lever to N.

REMOVAL 1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL 2. REMOVE FRONT WHEEL RH. 3. REMOVE REAR WHEEL (for 4WD) (a) Move the select lever to N. REMOVAL 1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL 2. REMOVE FRONT WHEEL RH 3. REMOVE REAR WHEEL (for 4WD) (a) Move the select lever to N. (b) Check that the parking brake is released. (c) Remove

More information

DESCRIPTION AND OPERATION

DESCRIPTION AND OPERATION 303-01B-10 Engine 3.0L 303-01B-10 DESCRIPTION AND OPERATION Upper Engine Components G72932 en 303-01B-11 Engine 3.0L 303-01B-11 DESCRIPTION AND OPERATION (Continued) Item Part Number Description 1 9H589

More information

COMPONENT LOCATOR > DISASSEMBLED VIEWS

COMPONENT LOCATOR > DISASSEMBLED VIEWS Page 1 of 45 2006 Pontiac Grand Prix 3.8L Eng Base Service Manual: ENGINE MECHANICAL - 3.8L COMPONENT LOCATOR > DISASSEMBLED VIEWS Fig 1: Engine Block Component Views Callout Component Name 100 Engine

More information

Intake Manifold: Service and Repair Removal

Intake Manifold: Service and Repair Removal 1992 Toyota Truck Pickup 2WD V6-180.5 2959cc 3.0L SOHC (3VZ-E) Copyright 2013, ALLDATA 10.52 Page 1 Intake Manifold: Service and Repair Removal NOTE: If removing and later reinstalling the fluid coupling

More information

REMOVAL. 16. LOOSEN CRANKSHAFT PULLEY BOLT Using SST, loosen the pulley bolt. SST ( ), EM 20 SST TIMING BELT

REMOVAL. 16. LOOSEN CRANKSHAFT PULLEY BOLT Using SST, loosen the pulley bolt. SST ( ), EM 20 SST TIMING BELT EM20 REMOVAL EM11901 1. REMOVE NO.1 ENGINE UNDER COVER 2. DRAIN ENGINE COOLANT 3. REMOVE AIR CLEANER INLET 4. REMOVE AIR CLEANER ASSEMBLY 5. REMOVE NO.2 CYLINDER HEAD COVER 6. REMOVE IGNITION COILS (See

More information

2000 Toyota Celica GT-S L4-1762cc 1.8L DOHC MFI - Removal and Installation

2000 Toyota Celica GT-S L4-1762cc 1.8L DOHC MFI - Removal and Installation Page 1 of 8 Removal and Installation REMOVAL 1. REMOVE HOOD Torque: 13 Nm (130 kgf-cm, 9 ft. lbs.) 2. REMOVE BATTERY 3. REMOVE ECM AND ECM CASE Torque: 6.9 Nm (70 kgf-cm, 61 inch lbs.) 4. REMOVE ECM BRACKET

More information

IGNITION SYSTEM IG 1 2GR-FE IGNITION IGNITION SYSTEM INSTRUMENT PANEL JUNCTION BLOCK - IG2 FUSE ECM

IGNITION SYSTEM IG 1 2GR-FE IGNITION IGNITION SYSTEM INSTRUMENT PANEL JUNCTION BLOCK - IG2 FUSE ECM NITION SYSTEM EINE 2GR-FE PARTS LOCATION 2GR-FE NITION NITION SYSTEM 1 INSTRUMENT PANEL JUNCTION BLOCK - 2 FUSE ECM EINE ROOM NO. 1 RELAY BLOCK, JUNCTION BLOCK - 2 RELAY - AM2 FUSE A126956E01 2 2GR-FE

More information

ENGINE <6G7> Click on the applicable bookmark to selected the required model year.

ENGINE <6G7> Click on the applicable bookmark to selected the required model year. ENGINE Click on the applicable bookmark to selected the required model year. 11A-2 ENGINE CONTENTS GENERAL INFORMATION... 3 SERVICE SPECIFICATIONS... 3 SEALANT... 4 SPECIAL TOOLS... 4 ON-VEHICLE

More information

1996 Aerostar/Ranger/Explorer

1996 Aerostar/Ranger/Explorer Page 1 of 11 Section 03-01B: Engine, 3.0L V-6 IN-VEHICLE SERVICE 1996 Aerostar and Ranger Vehicles Workshop Manual Water Pump SPECIAL SERVICE TOOL(S) REQUIRED Description Tool Number Fan Clutch Holding

More information

EG1 509 OIL COOLER COMPONENTS FOR REMOVAL AND INSTALLATION

EG1 509 OIL COOLER COMPONENTS FOR REMOVAL AND INSTALLATION 3SGTE ENGINE EG1509 OIL COOLER COMPONENTS FOR REMOVAL AND INSTALLATION EG1510 3SGTE ENGINE 3SGTE ENGINE EG1511 OIL COOLER REMOVAL (See Components for Removal and Installation) 1. DISCONNECT CABLE FROM

More information

Engine Removal/Installation

Engine Removal/Installation Engine Removal/Installation Make sure jacks and safety stands are placed properly and hoist brackets are attached to correct positions on the engine. (See Section 1). Apply parking brake and block rear

More information

Lower Intake Manifold Replacement

Lower Intake Manifold Replacement Lower Intake Manifold Replacement Removal Procedure 1. Turn OFF all the lamps and the accessories. 2. Ensure the ignition switch is in the OFF position. 3. Disconnect the negative battery cable from the

More information

2002 Mustang Workshop Manual

2002 Mustang Workshop Manual Page 1 of 13 SECTION 303-01B: Engine 4.6L (2V) 2002 Mustang Workshop Manual REMOVAL Procedure revision date: 01/02/2003 Cylinder Heads Special Tool(s) Remover, Crankshaft Vibration Damper 303-009 (T58P-6316-D)

More information

EM 38 2TR-FE ENGINE MECHANICAL CAMSHAFT REMOVAL

EM 38 2TR-FE ENGINE MECHANICAL CAMSHAFT REMOVAL 38 2TR-FE ENGINE MECHNICL CMSHFT ROVL 1. DISCONNECT CLE FROM NEGTIVE TTERY TERMINL 2. ROVE NO. 1 ENGINE UNDER COVER SU- SSLY (for 4WD) (a) Remove the 4 bolts, then remove the No. 1 engine under cover.

More information

SUPERCHARGER. ON-VEHICLE INSPECTION 1. INSPECT SUPERCHARGER OIL LEVEL HINT: With the engine cold, check the oil level on the dipstick.

SUPERCHARGER. ON-VEHICLE INSPECTION 1. INSPECT SUPERCHARGER OIL LEVEL HINT: With the engine cold, check the oil level on the dipstick. EG45 ONVEHICLE INSPECTION 1. INSPECT OIL LEVEL HINT: With the engine cold, check the oil level on the dipstick. (a) Park the vehicle on a level spot and turn the engine off. (b) 4WD: Remove the LH front

More information

2003 Taurus/Sable Workshop Manual

2003 Taurus/Sable Workshop Manual Page 1 of 24 SECTION 303-01A: Engine 3.0L (2V) ASSEMBLY 2003 Taurus/Sable Workshop Manual Engine Special Tool(s) Piston Ring Compressor 303- D032 (D81L-6002-C) Camshaft Bearing Set 303-017 (T65L-6250-A)

More information

TURBOCHARGER ON VEHICLE INSPECTION TC 7

TURBOCHARGER ON VEHICLE INSPECTION TC 7 TC7 ONVEHICLE INSPECTION 1. INSPECT INTAKE AIR SYSTEM Check for leakage or clogging between the air cleaner and turbocharger inlet and between the turbocharger outlet and cylinder head. Clogged air cleaner...

More information

Disconnect the APP sensor harness connector. See Fig. 4. Remove the accelerator pedal mounting nuts. Remove the APP assembly.

Disconnect the APP sensor harness connector. See Fig. 4. Remove the accelerator pedal mounting nuts. Remove the APP assembly. ENGINE CONTROLS - REMOVAL, OVERHAUL & INSTALLATION - 6.6L DIESEL... Page 1 of 41 FUEL SYSTEMS ACCELERATOR PEDAL POSITION SENSOR Removal & Installation Disconnect the APP sensor harness connector. See Fig.

More information

Page 1 of 44 REPLACEMENT 1. 2. 3. 4. REMOVE ENGINE UNDER COVER RH DRAIN COOLANT (See REPLACEMENT ) REMOVE FRONT WHEEL RH REMOVE CYLINDER HEAD COVER NO. 2 a. Remove the 2 nuts, 2 clips and cylinder head

More information

THREE WAY CATALYTIC CONVERTER (TWC) SYSTEM

THREE WAY CATALYTIC CONVERTER (TWC) SYSTEM EC26 THREEWAY CATALYTIC CONVERTER (TWC) SYSTEM To reduce C0, HC and NOx emissions, they are oxidized, reduced and converted to carbon dioxide (C02), water 1H20Y and nitrogen (NO by the threeway catalytic

More information

COOLING SYSTEM ON-VEHICLE INSPECTION CO 1

COOLING SYSTEM ON-VEHICLE INSPECTION CO 1 2GR-FE OLING OLING SYSTEM A133894 OLING SYSTEM ON-VEHICLE INSPECTION 1 1. CHECK FOR ENGINE OLANT LEAKS CAUTION: Do not remove the radiator cap while the engine and radiator are still hot. Pressurized,

More information

REMOVAL & INSTALLATION

REMOVAL & INSTALLATION REMOVAL & INSTALLATION NOTE: For reassembly reference, label all electrical connectors, vacuum hoses and fuel lines before removal. Also place mating marks on engine hood and other major assemblies before

More information

SECTION C Engine 5.4L (4V)

SECTION C Engine 5.4L (4V) 303-01C-i Engine 5.4L (4V) 303-01C-i SECTION 303-01C Engine 5.4L (4V) CONTENTS PAGE SPECIFICATIONS... 303-01C-2 303-01C-2 Engine 5.4L (4V) 303-01C-2 SPECIFICATIONS Material Motorcraft Metal Surface Prep

More information

DISASSEMBLED VIEWS. Disassembled Views. Engine Covers and Component Assemblies (1 of 2) (LF1, LFW or LFX)

DISASSEMBLED VIEWS. Disassembled Views. Engine Covers and Component Assemblies (1 of 2) (LF1, LFW or LFX) 2012 Cadillac CTS Wagon AWD V6-3.0L Vehicle > Engine, Cooling and Exhaust > Engine > Locations > Components DISASSEMBLED VIEWS Disassembled Views Engine Covers and Component Assemblies (1 of 2) (LF1, LFW

More information

1999 E-Series Workshop Manual

1999 E-Series Workshop Manual http://www.fordservicecontent.com/pubs/content/~wsxm/~mus~len/21/sxm31c16.h... Page 1 of 3 SECTION 303-01C: Engine 6.8L 1999 E-Series Workshop Manual IN-VEHICLE REPAIR Procedure revision date: 06/30/1998

More information

Engine. Special Tool(s) Compressor, Piston Ring 303-D032 (D81L-6002-C) or equivalent. Compressor, Valve Spring (T93P-6565-AR)

Engine. Special Tool(s) Compressor, Piston Ring 303-D032 (D81L-6002-C) or equivalent. Compressor, Valve Spring (T93P-6565-AR) SECTION 303-01C: Engine 5.4L (4V) 2009 Mustang Workshop Manual ASSEMBLY Procedure revision date: 12/12/2008 Engine Special Tool(s) Compressor, Piston Ring 303-D032 (D81L-6002-C) or equivalent Compressor,

More information

Audi > B4 > Liter V6 2V Engine Mechanical, Engine Code(s): AAH, AFC 10 Engine Assembly

Audi > B4 > Liter V6 2V Engine Mechanical, Engine Code(s): AAH, AFC 10 Engine Assembly Audi > B4 > 1993 1995 2.8 Liter V6 2V Engine Mechanical, Engine Code(s): AAH, AFC 10 Engine Assembly Removing The engine is removed from above, after being separated from the transmission. Note: All tie

More information

INSTALLATION. NOTICE: Do not scratch the angle sensor of the timing pulley.

INSTALLATION. NOTICE: Do not scratch the angle sensor of the timing pulley. EM26 INSTALLATION EM11B01 1. INSTALL OIL PUMP PULLEY (a) Align the cutouts of the pulley and shaft, and slide on the pulley. (b) Using, install the pulley nut. 0996010010 (0996201000, 0996300600) Torque:

More information

REMOVAL. 5. REMOVE OIL DIPSTICK GUIDE (a) Remove the bolt, dipstick guide and engine wire bracket. (b) Remove the O ring from the dipstick guide.

REMOVAL. 5. REMOVE OIL DIPSTICK GUIDE (a) Remove the bolt, dipstick guide and engine wire bracket. (b) Remove the O ring from the dipstick guide. EM34 ENGINE MECHANICAL (2RZFE, 3RZFE) P23426 EM1MY01 REMOVAL 1. DRAIN ENGINE COOLANT 2. DISCONNECT THESE CABLES: (a) Disconnect the accelerator cable from the throttle body. A/T: Disconnect the throttle

More information

Torque Guidelines (Z 22 SE)

Torque Guidelines (Z 22 SE) Page 1 of 14 Torque Guidelines (Z 22 SE) No. Designation Nm 1 Retaining bolts, coolant pump sprocket to coolant pump 2 Retaining bolts, balancer shaft timing chain guide rail to 3 Retaining bolts, balancer

More information

INJECTOR ON VEHICLE INSPECTION 1. CHECK INJECTOR OPERATION

INJECTOR ON VEHICLE INSPECTION 1. CHECK INJECTOR OPERATION EG1187 INJECTOR ONVEHICLE INSPECTION 1. CHECK INJECTOR OPERATION Check for operating sound from each injector. (a) With the engine running or cranking, use a sound scope to check that there is normal operating

More information

2001 Lincoln LS Workshop Manual

2001 Lincoln LS Workshop Manual Page 1 of 10 SECTION 303-01B: Engine 3.9L 2001 Lincoln LS Workshop Manual IN-VEHICLE REPAIR Procedure revision date: 05/16/2000 Intake Manifold Removal 1. Disconnect the battery ground cable. For additional

More information

2002 Explorer Sport/Sport Trac Workshop Manual

2002 Explorer Sport/Sport Trac Workshop Manual Page 1 of 17 SECTION 303-01: Engine 4.0L Single Overhead Camshaft (SOHC) IN-VEHICLE REPAIR Procedure revision date: 07/13/2005 Cylinder Head Special Tool(s) Spark Plug Wire Remover 303-106 (T74P-6666-A)

More information

Intake Components 1117

Intake Components 1117 Item Part Number Description 1 W705654 Bolt 2 N807309 Bolt (2 req'd) 3 9F460 Bracket 4 N807071 Bolt (5 req'd) 5 9A448 Intake manifold (upper) 6 9E498 Vacuum harness 7 9F792 Fuel injection supply manifold

More information

1999 F-150/250 Workshop Manual

1999 F-150/250 Workshop Manual Page 1 of 8 SECTION 303-01B: Engine 4.6L and 5.4L IN-VEHICLE REPAIR Procedure revision date: 02/03/1999 Intake Manifold Lightning Removal WARNING: Do not smoke or carry lighted tobacco or open flame of

More information

NOTE: Do not disassemble upper intake manifold from lower intake manifold unless replacement of one of the components is necessary.

NOTE: Do not disassemble upper intake manifold from lower intake manifold unless replacement of one of the components is necessary. Fig. 2: Lower Intake Manifold Bolt Tightening Sequence INTAKE MANIFOLD (UPPER) NOTE: Do not disassemble upper intake manifold from lower intake manifold unless replacement of one of the components is necessary.

More information

Cylinder Head. Special Tool(s) Compressor, Valve Spring (T93P-6565-AR) Heavy Duty Floor Crane or equivalent

Cylinder Head. Special Tool(s) Compressor, Valve Spring (T93P-6565-AR) Heavy Duty Floor Crane or equivalent SECTION 303-01C: Engine 5.4L (4V) 2009 Mustang Workshop Manual INSTALLATION Procedure revision date: 04/03/2009 Cylinder Head Special Tool(s) Compressor, Valve Spring 303-452 (T93P-6565-AR) Heavy Duty

More information

IN-VEHICLE REPAIR. Upper Intake Manifold

IN-VEHICLE REPAIR. Upper Intake Manifold 303-01-1 Engine 3.9L and 4.2L 303-01-1 IN-VEHICLE REPAIR Upper Intake Manifold Special Tool(s) Remover, Spark Plug Wire 303-106 (T74P-6666-A) Material Item Silicone Brake Caliper Grease and Dielectric

More information

EM 6 VALVE CLEARANCE ENGINE MECHANICAL EM11I 01 ADJUSTMENT HINT:

EM 6 VALVE CLEARANCE ENGINE MECHANICAL EM11I 01 ADJUSTMENT HINT: EM6 ADJUSTMENT EM11I01 Inspect and adjust the valve clearance when the engine is cold. 1. REMOVE NO.1 ENGINE UNDER COVER 2. DRAIN ENGINE COOLANT 3. REMOVE AIR CLEANER INLET 4. REMOVE AIR CLEANER ASSEMBLY

More information

10/20/ Ford E 250 Engine Mechanical > Engine, 4.6L and 5.4L > IN VEHICLE REPAIR > Intake Manifold 5.4L

10/20/ Ford E 250 Engine Mechanical > Engine, 4.6L and 5.4L > IN VEHICLE REPAIR > Intake Manifold 5.4L 2005 Ford E 250 : Engine Mechanical > Engine, 4.6L and 5.4L > IN VEHICLE REPAIR > Intake Manifold 5.4L Intake Manifold 5.4L Listen SECTION 303 01A: Engine 4.6L and 5.4L 2005 E Series Workshop Manual IN

More information

EG-37 ENGINE MECHANICAL TIMING BELT COMPONENTS FOR REMOVAL AND INSTALLATION 2JZ-GE

EG-37 ENGINE MECHANICAL TIMING BELT COMPONENTS FOR REMOVAL AND INSTALLATION 2JZ-GE ENGINE EG37 TIMING BELT COMPONENTS FOR REMOVAL AND INSTALLATION 2JZGE EG38 ENGINE 2JZ GTE ENGINE EG39 TIMING BELT REMOVAL (See Components for Removal and Installation) 1. REMOVE BATTERY AND BATTERY TRAY

More information

https://www.hyundaitechinfo.com/viewer/content.asp?isprint=true&imgnum=1&print_titl...

https://www.hyundaitechinfo.com/viewer/content.asp?isprint=true&imgnum=1&print_titl... Page 1 of 7 VELOSTER(FS) >2013 > G 1.6 T-GDI > Engine Mechanical System > General Information > Specifications Specifications General Type Description Specifications Except Europe In-line, DOHC Number

More information

ENGINE ACCESSORIES. D20DT Engine. PCV valve and oil separator. Turbo charger. EGR pipe (LH, Center, RH) Cooling fan clutch. Auto tensioner.

ENGINE ACCESSORIES. D20DT Engine. PCV valve and oil separator. Turbo charger. EGR pipe (LH, Center, RH) Cooling fan clutch. Auto tensioner. 01 41 ENGINE ACCESSORIES Engine GENERAL PCV valve and oil separator Turbo charger Power steering pump Fuel return hose Alternator EGR pipe (LH, Center, RH) Cooling fan clutch EGR valve Auto tensioner Cable

More information

TORQUE SPECIFICATIONS

TORQUE SPECIFICATIONS TORQUE SPECIFICATIONS TORQUE SPECIFICATIONS Application Ft. Lbs. (N.m) A/C Compressor Bracket Bolts Upper Vertical Bolt 16-21 (22-29) Horizontal Bolts 32-43 (43-58) A/C Compressor-To-Bracket Bolts 32-43

More information

Page 1 of 9 SECTION 303-01B: Engine 2.0L SPI 2002 Focus Workshop Manual ASSEMBLY Procedure revision date: 12/14/2000 Engine Special Tool(s) Crankshaft Rear Seal Pilot 303-329 (T88P-6701-B2) Crankshaft

More information

TIMING BELT COMPONENTS EM 15

TIMING BELT COMPONENTS EM 15 ENGINE MECHANICAL COMPONENTS EM15 EM16 ENGINE MECHANICAL COMPONENTS (Cont d) ENGINE MECHANICAL EM17 REMOVAL OF (See pages EM15 and 16) 1. DISCONNECT CABLE FROM NEGATIVE TERMINAL OF BATTERY CAUTION: Work

More information

REMOVAL. 10. REMOVE FRONT SUSPENSION MEMBER BRACE Remove the 8 bolts and brace.

REMOVAL. 10. REMOVE FRONT SUSPENSION MEMBER BRACE Remove the 8 bolts and brace. EM64 ENGINE MECHANICAL (2JZGE) EM1S801 REMOVAL 1. REMOVE ENGINE UNDER COVER 2. DRAIN ENGINE COOLANT 3. DRAIN ENGINE OIL 4. REMOVE ENGINE COVER Remove the 4 nuts and engine cover. 5. REMOVE AIR CLEANER

More information

1983 BMW 320i. 1.8L 4-CYL 1983 Engines - 1.8L 4-Cylinder Engines - 1.8L 4-Cylinder

1983 BMW 320i. 1.8L 4-CYL 1983 Engines - 1.8L 4-Cylinder Engines - 1.8L 4-Cylinder ENGINE IDENTIFICATION 1.8L 4-CYL 1983 Engines - 1.8L 4-Cylinder For engine repair procedures not covered in this article, see ENGINE OVERHAUL PROCEDURES - GENERAL INFORMATION article in the GENERAL INFORMATION

More information

2004 Toyota CAMRY. Submodel: Engine Type: L4 Liters: 2.4 Fuel Delivery: FI Fuel: GAS

2004 Toyota CAMRY. Submodel: Engine Type: L4 Liters: 2.4 Fuel Delivery: FI Fuel: GAS 2004 Toyota CAMRY Submodel: Engine Type: L4 Liters: 2.4 Fuel Delivery: FI Fuel: GAS REPLACEMENT 1. REMOVE HOOD SU-ASSY 2. REMOVE FRONT WHEEL RH 3. REMOVE ENGINE UNDER COVER LH 4. REMOVE ENGINE UNDER COVER

More information

Position of Parts in Engine Compartment

Position of Parts in Engine Compartment ELECTRICAL WIRING ROUTING [5S FE] Position of Parts in Engine Compartment A 1 A/C Condenser Fan Motor E 4 Engine Coolant Temp. Sensor (EFI Water Temp. A 2 A/C Magnetic Clutch and Lock Sensor Sensor) A

More information

DISASSEMBLY AND REASSEMBLY

DISASSEMBLY AND REASSEMBLY 24 01 DISASSEMBLY AND REASSEMBLY COMPONENTS AND SPECIAL TOOLS Injector Puller Y99220072B Glow Plug Wrench Y99220132B Fuel Pipe Wrench Sealing Caps 665 995 5844 Injector Copper Washer Puller Y99220022B

More information

1 of 12 11/20/2016 9:32 PM

1 of 12 11/20/2016 9:32 PM 1 of 12 11/20/2016 9:32 PM Caution: After removing timing chain, do not turn crankshaft and camshaft separately, or valves will strike piston heads. Apply new engine oil to the sliding surfaces when Installing

More information

D-1: FAN COVER. DESCRIPTION 1 Asm., Shroud, Upper

D-1: FAN COVER. DESCRIPTION 1 Asm., Shroud, Upper D-: FAN COVER Asm., Shroud, Upper 9639-000 Screw, Tappinmg 9390-305068-00K 3 Clamp 9689-000 Plug, Rubber 96339-000 5 Elbow, Outlet 9650-000 6 Bolt 96000-06058-08C 3 7 Cover Set, Fly Wheel 9609-00 8 Cap

More information

Position of Parts in Engine Compartment

Position of Parts in Engine Compartment ELECTRICAL WIRING ROUTING [3S GTE] Position of Parts in Engine Compartment A 1 A/C Ambient Temp. Sensor D 1 Date Link Connector 1 (Check Connector) A 2 A/C Condenser Fan Motor D 2 Distributor A 4 A/C Magnetic

More information

DISASSEMBLY. Engine. CAUTION: Remove the cylinder heads before removing the crankshaft. Failure to do so can result in engine damage.

DISASSEMBLY. Engine. CAUTION: Remove the cylinder heads before removing the crankshaft. Failure to do so can result in engine damage. 303-01A-1 DISASSEMBLY Engine Special Tool(s) Remover, Crankshaft Vibration Damper 303-101 (T74P-3616-A) Special Tool(s) Crankshaft Socket 303-674 303-01A-1 Remover, Crankshaft Vibration Damper 303-773

More information

5.7L ENGINE PARTS BOOK. Not for. Reproduction

5.7L ENGINE PARTS BOOK. Not for. Reproduction 5.7L ENGINE PARTS BOOK Engine Model: Engine Family: PSI, Industrial Engine Spec N.: 39004120-39004248 Parts Book Revision: December, 2015 TABLE OF CONTENTS SECTION PAGE CYLINDER BLOCK... 3-5 CYLINDER HEAD...

More information

1998 F-150/250 Workshop Manual

1998 F-150/250 Workshop Manual Page 1 of 13 SECTION 303-01B: Engine 4.6L and 5.4L 1998 F-150/250 Workshop Manual IN-VEHICLE REPAIR Procedure revision date: 03/07/2000 Intake Manifold Removal WARNING: Do not smoke or carry lighted tobacco

More information

EMISSION CONTROL (AUX. EMISSION CONTROL DEVICES) H4SO

EMISSION CONTROL (AUX. EMISSION CONTROL DEVICES) H4SO EMISSION CONTROL (AUX. EMISSION CONTROL DEVICES) H4SO SYSTEM OVERVIEW 1. System Overview There are three emission control systems, which are as follows: Crankcase emission control system Exhaust emission

More information

COOLING SYSTEM ON-VEHICLE INSPECTION CO 1

COOLING SYSTEM ON-VEHICLE INSPECTION CO 1 Radiator Cap Tester 2AZ-FE OLING OLING SYSTEM A112194E01 A112306 OLING SYSTEM ON-VEHICLE INSPECTION 1 1. CHECK OLING SYSTEM FOR LEAKS (a) Remove the radiator reservoir cap. CAUTION: To avoid the danger

More information

ENGINE SPECIFICATIONS

ENGINE SPECIFICATIONS ENGINE SPECIFICATIONS MECHANICAL LOCATION INDEX Engine cover 1 (See ENGINE COVER REMOVAL/INSTALLATION.) 2 Drive belt Page 1 (See DRIVE BELT DEFLECTION/TENSION INSPECTION.) (See DRIVE BELT ADJUSTMENT.)

More information

26/01/2017 3GR-FSE ENGINE MECHANICAL: ENGINE UNIT: DISASSEMBLY; 2006 MY GS300 [01/ ]

26/01/2017 3GR-FSE ENGINE MECHANICAL: ENGINE UNIT: DISASSEMBLY; 2006 MY GS300 [01/ ] Last Modified: 8-24-2016 6.6 A Doc ID: RM000000T4X000X Model Year Start: 2006 Model: GS300 Prod Date Range: [01/2005 - ] Title: 3GR-FSE ENGINE MECHANICAL: ENGINE UNIT: DISASSEMBLY; 2006 MY GS300 [01/2005

More information

EG1 485 OIL PUMP COMPONENTS FOR REMOVAL AND INSTALLATION

EG1 485 OIL PUMP COMPONENTS FOR REMOVAL AND INSTALLATION EG1485 OIL PUMP COMPONENTS FOR REMOVAL AND INSTALLATION EG1486 EG1487 EG1488 OIL PUMP REMOVAL (See Components for Removal and Installation) HINT: When repairing the oil pump, the oil pan an^ strainer should

More information

STARTER COMPONENTS FOR REMOVAL AND INSTALLATION

STARTER COMPONENTS FOR REMOVAL AND INSTALLATION Removal STARTER COMPONENTS FOR REMOVAL AND INSTALLATION Starter Components For Removal And Installation REMOVAL OF STARTER 1. DISCONNECT CABLE FROM NEGATIVE TERMINAL OF BATTERY CAUTION: Work must be started

More information

IN-VEHICLE REPAIR. Cylinder Head. Special Tool(s) Timing Tool, Crankshaft TDC (T97T-6303-A) or. Special Tool(s) equivalent

IN-VEHICLE REPAIR. Cylinder Head. Special Tool(s) Timing Tool, Crankshaft TDC (T97T-6303-A) or. Special Tool(s) equivalent 303-01A-1 IN-VEHICLE REPAIR Cylinder Head Special Tool(s) Torque Wrench Extension 303-575 (T97T-6256-F) or equivalent Special Tool(s) 303-01A-1 Timing Tool, Crankshaft TDC 303-573 (T97T-6303-A) or equivalent

More information

9. Engine Assembly ENGINE ASSEMBLY

9. Engine Assembly ENGINE ASSEMBLY 9. Engine Assembly A: REMOVAL 1) Set the vehicle on a lift. 2) Open the front hood fully, and then support with the hood stay. 3) Collect the refrigerant from A/C system. 4) Release the fuel pressure.

More information

1989 Nissan 300ZX. 3.0L V6 - VIN [H] & 3.0L V6 TURBO - VIN [C] 1989 Engines - 3.0L & 3.0L Turbo V6

1989 Nissan 300ZX. 3.0L V6 - VIN [H] & 3.0L V6 TURBO - VIN [C] 1989 Engines - 3.0L & 3.0L Turbo V6 INTAKE MANIFOLD Removal 1. Release fuel system pressure. Disconnect battery and drain cooling system. Disconnect vacuum and coolant lines attached to intake manifold and label accordingly. Remove throttle

More information

COMPONENT LOCATIONS GROUP CONTENTS FUSIBLE LINK, FUSE AND IOD OR STORAGE CONNECTOR RELAY OTHER DEVICES...

COMPONENT LOCATIONS GROUP CONTENTS FUSIBLE LINK, FUSE AND IOD OR STORAGE CONNECTOR RELAY OTHER DEVICES... 70-1 GROUP 70 COMPONENT LOCTIONS CONTENTS RELY........................ 70-2 OTHER DEVICES............... 70-3 CONTROL UNIT................. 70-4 INSPECTION TERMINL......... 70-7 SENSOR.......................

More information

ON-VEHICLE INSPECTION

ON-VEHICLE INSPECTION Last Modified: 4-26-2007 Service Category: Engine/Hybrid System 1.6 G Section: Engine Mechanical Model Year: 2007 Model: 4Runner Doc ID: RM0000017L8004X Title: 1GR-FE ENGINE MECHANICAL: ENGINE: ON-VEHICLE

More information

Torque Specifications for 2003 Hyundai Tiburon (GK) 2.7L DOHC

Torque Specifications for 2003 Hyundai Tiburon (GK) 2.7L DOHC Torque Specifications for 2003 Hyundai Tiburon (GK) 2.7L DOHC Engine Mechanical System Camshaft sprocket bolt 90 ~ 110 900 ~ 1,100 65 ~ 80 Cylinder head cover bolt 8 ~ 10 80 ~ 100 5.8 ~ 7.2 Main bearing

More information