Cylinder Head Assembly: Removal and Replacement Repair Procedures
|
|
|
- Oswald Mathews
- 5 years ago
- Views:
Transcription
1 2007 Kia Rio L4-1.6L Copyright 2013, ALLDATA Page 1 Cylinder Head Assembly: Removal and Replacement Repair Procedures COMPONENT
2 2007 Kia Rio L4-1.6L Copyright 2013, ALLDATA Page 2 REMOVAL Engine removal is not required for this procedure. CAUTION: 1) Use Fender cover to avoid damaging painted surfaces. 2) To avoid damaging the cylinder head, wait until the engine coolant temperature drops below normal temperature before removing it. 3) When handling a metal gasket, take care not to fold the gasket or damage the contact surface of the gasket. 4) To avoid damage, unplug the wiring connectors carefully while holding the connector portion. OTE: 1) Mark all wiring and hoses to avoid misconnection. 2) Inspect the timing belt before removing the cylinder head. 3) Turn the crankshaft pulley so that the No. 1 piston is at top dead center. 1. Disconnect the terminals(a) from battery and remove the battery. 2. Remove the engine cover(a).
3 2007 Kia Rio L4-1.6L Copyright 2013, ALLDATA Page 3 3. Remove the under cover(a). 4. Drain the engine coolant. Remove the radiator cap to speed draining. 5. Remove the intake air hose and air cleaner assembly. (1) Disconnect the AFS(Air Flow Sensor) connector(a). (2) Disconnect the breather hose(b) from intake air hose(d). (3) Remove the intake air hose(d) and air cleaner upper cover(c). (4) Disconnect the ECM connector(a) and ECM connector(b) (A/T only). (5) Remove the air cleaner element and air cleaner lower cover(c). 6. Remove the battery tray(a). 7. Remove the upper radiator hose(a) and lower radiator hose(b).
4 2007 Kia Rio L4-1.6L Copyright 2013, ALLDATA Page 4 8. Remove the heater hoses(a). 9. Remove the fuel hose(b). 10. Remove the accelerator cable(a) by loosening the lock-nut, then slip the cable end out of the throttle linkage. 11. Disconnect the TPS (Throttle Position Sensor) connector(b). 12. Remove the engine wire harness connectors and wire harness clamps from cylinder head and the intake manifold. (1) Disconnect the rear oxygen sensor connector (A). (2) Disconnect the air conditioner compressor switch connector (B). (3) Disconnect the knock sensor connector (C). (4) Disconnect the injector connectors(no.3,4) (D). (5) Disconnect the injector connectors(no.1,2) (E) (6) Remove the wire harness bracket(a). (7) Disconnect the ISA (Idle Speed Actuator) connector (B).
5 2007 Kia Rio L4-1.6L Copyright 2013, ALLDATA Page 5 (8) Disconnect the front oxygen sensor connector(a). (9) Disconnect the CKP(Crankshaft Position Sensor) connector (B). (10) Disconnect the OCV (Oil Control Valve) connector (C). (11) Disconnect the ignition coil connector(a). (12) Disconnect the ignition coil condenser connector(b). (13) Disconnect the CMP(Camshaft Position Sensor) connector(c). (14) Disconnect the ground cable(d). (15) Remove the wire harness bracket(e). 13. Disconnect the hose(a) of the PCSV (Purge Control Solenoid Valve) side. 14. Remove the brake booster vacuum hose(b). 15. Remove the power steering pump and fix the pump to vehicle with a wire. 16. Remove the ignition coil. 17. Remove the exhaust manifold. 18. Remove the intake manifold. 19. Remove the timing belt. 20. Remove the cylinder head cover. 21. Remove the camshaft sprocket. 22. Remove the timing chain auto tensioner(a). 23. Remove the camshaft bearing caps(a) and camshafts (B).
6 2007 Kia Rio L4-1.6L Copyright 2013, ALLDATA Page Remove the OCV (Oil Control Valve)(A). 25. Remove the OCV (Oil Control Valve) filter(a). 26. Remove the engine mounting support bracket fixing bolts(a). 27. Remove the cylinder head bolts, then remove the cylinder head. (1) Using 8mm hexagon wrench, uniformly loosen and remove the 10 cylinder head bolts, in several passes, in the sequence shown. CAUTION: Head warpage or cracking could result from removing bolts in an incorrect order. (2) Lift the cylinder head from the dowels on the cylinder block and replace the cylinder head on wooden blocks on a bench. CAUTION: Be careful not to damage the contact surfaces of the cylinder head and cylinder block.
7 2007 Kia Rio L4-1.6L Copyright 2013, ALLDATA Page 7 INSTALLATION NOTE: 1) Thoroughly clean all parts to be assembled. 2) Always use a new cylinder head and manifold gasket. 3) Always use a new cylinder head bolt. 4) The cylinder head gasket is a metal gasket. Take care not to bend it. 5) Rotate the crankshaft, set the No.1 piston at TDC. 1. Install the cylinder head gasket(a) on the cylinder block. NOTE: Be careful of the installation direction. 2. Place the cylinder head quietly in order not to damage the gasket with the bottom part of the end. 3. Install the cylinder head bolts. (1) Apply a light coat if engine oil on the threads and under the heads of the cylinder head bolts. (2) Using 8mm and 10mm hexagon wrench, install and tighten the 10 cylinder head bolts and plate washers, in several passes, in the sequence shown. Tightening torque : 29.4N.m (3.0kgf.m, 21.7lb-ft) > Release all bolts -> 29.4N.m (3.0kgf.m, 21.7lb-ft) Install the engine mounting support bracket fixing bolts(a). 5. Install the OCV (Oil Control Valve) filter(a). Tightening torque : N.m ( kgf.m, lb-ft)
8 2007 Kia Rio L4-1.6L Copyright 2013, ALLDATA Page 8 NOTE: 1) Always use a new OCV (Oil Control Valve) filter gasket. 2) Keep clean the OCV (Oil Control Valve) filter. 6. Install the OCV (Oil Control Valve)(A). Tightening torque : N.m ( kgf.m, lb-ft) CAUTION: 1) Do not reuse the OCV (Oil Control Valve) when dropped. 2) Keep clean the OCV (Oil Control Valve). 3) Do not hold the OCV (Oil Control Valve) sleeve during servicing. 4) When the OCV (Oil Control Valve) is installed on the engine, do not move the engine with holding the OCV (Oil Control Valve) yoke. 7. Install the camshafts. (1) Align the camshaft timing chain with the intake timing chain sprocket and exhaust timing chain sprocket as shown. (2) Install the camshaft(a) and bearing caps(b). Tightening torque : N.m ( kgf.m, lb-ft) (3) Install the timing chain auto tensioner(a). Tightening torque : N.m ( kgf.m, lb-ft)
9 2007 Kia Rio L4-1.6L Copyright 2013, ALLDATA Page 9 8. Using the SST ( ), install the camshaft bearing oil seal. 9. Install the camshaft sprocket. 10. Install the cylinder head cover. (1) Install the cylinder head cover gasket(a) in the groove of the cylinder head cover(b). NOTE: 1) Before installing the cylinder head cover gasket, thoroughly clean the cylinder head cover and the groove. 2) When installing, make sure the cylinder head cover gasket is seated securely in the corners of the recesses with no gap. (2) Apply liquid gasket to the head cover gasket at the corners of the recess. NOTE: 1) Use liquid gasket, loctite No ) Check that the mating surfaces are clean and dry before applying liquid gasket. 3) After assembly, wait at least 30 minutes before filling the engine with oil. (3) Install the cylinder head cover(a) with bolts(b). Uniformly tighten the bolts in several passes. Pre-tighten all bolts by N.m ( kgf.m, lb-ft) and then tighten by the specified torque. Tightening torque : N.m ( kgf.m, lb-ft)
10 2007 Kia Rio L4-1.6L Copyright 2013, ALLDATA Page Install the timing belt. 12. Install the intake manifold. 13. Install the exhaust manifold. 14. Install the ignition coil Install the power steering pump. 16. Install the brake booster hose(b). 17. Connect the hose(a) of the PCSV (Purge Control Solenoid Valve) side. 18. Install the engine wire harness connectors and wire harness clamps to the cylinder head and the intake manifold. (1) Install the wire harness bracket(e). (2) Connect the ground cable(d). (3) Connect the CMP(Camshaft position sensor) connector(c). (4) Connect the ignition coil condenser connector(b). (5) Connect the ignition coil connector(a). (6) Connect the OCV (Oil Control Valve) connector(c). (7) Connect the CKP(Crankshaft Position Sensor) connector(b). (8) Connect the front oxygen sensor connector(a). (9) Connect the ISA(Idle Speed Actuator) connector(b). (10) Install the wire harness bracket(a).
11 2007 Kia Rio L4-1.6L Copyright 2013, ALLDATA Page 11 (11) Connect the injector connectors (No.1,2) (E). (12) Connect the injector connectors (No.3,4) (D). (13) Connect the knock sensor connector(c). (14) Connect the air conditioner compressor switch connector(b). (15) Connect the rear oxygen sensor connector(a). 19. Connect the TPS (Throttle Position Sensor) connector (B). 20. Install the accelerator cable(a). 21. Install the fuel hose(b). 22. Install the heater hoses(a). 23. Install the upper radiator hose(a) and lower radiator hose(b). 24. Install the battery tray(a).
12 2007 Kia Rio L4-1.6L Copyright 2013, ALLDATA Page Install the intake air hose and air cleaner assembly. (1) Install the air cleaner element and air cleaner lower cover(c). Tightening torque : N.m ( kgf.m, lb-ft) (2) Connect the ECM connector(a) and ECM connector(b) (A/T only). (3) Install the intake air hose(d) and air cleaner upper cover(c). (4) Connect the breather hose(b) to intake air hose(d). (5) Connect the AFS(Air Flow Sensor) connector(a). 26. Install the under cover(a). 27. Install the engine cover(a). Tightening torque : N.m ( kgf.m, lb-ft)
13 2007 Kia Rio L4-1.6L Copyright 2013, ALLDATA Page Install the battery and connect the battery terminals(a). 29. Fill with engine coolant. 30. Start the engine and check for leaks. 31. Recheck engine coolant level and oil level.
REMOVAL AND INSTALLATION
2008 Kia Rondo V6-2.7L Vehicle > Engine, Cooling and Exhaust > Engine > Cylinder Head Assembly > Service and Repair > Removal and Replacement > Cylinder Head Assembly REMOVAL AND INSTALLATION REMOVAL CAUTION:
REMOVAL. Engine removal is not required for this procedure. Remove the engine cover(a).
1 of 25 12/11/2012 4:43 PM REMOVAL Engine removal is not required for this procedure. 1. Remove the engine cover(a). 2. 3. Remove the RH front wheel. Remove the 2 bolts(b) and RH side cover(a). 2 of 25
2012 Kia Soul L4 2.0L
2012 Kia Soul L4 2.0L Vehicle» Engine, Cooling and Exhaust» Engine» Timing Chain» Service and Repair» Repair Procedures» Part 1 Removal Engine removal is not required for this procedure. CAUTION: Use fender
Timing Belt: Service and Repair TIMING BELT
2008 Hyundai Accent L4-1.6L Copyright 2013, ALLDATA 10.52 Page 1 Timing Belt: Service and Repair TIMING BELT EMOVAL Engine removal is not required for this procedure. 1. Remove the engine cover. 2. Remove
REMOVAL. 5. REMOVE OIL DIPSTICK GUIDE (a) Remove the bolt, dipstick guide and engine wire bracket. (b) Remove the O ring from the dipstick guide.
EM34 ENGINE MECHANICAL (2RZFE, 3RZFE) P23426 EM1MY01 REMOVAL 1. DRAIN ENGINE COOLANT 2. DISCONNECT THESE CABLES: (a) Disconnect the accelerator cable from the throttle body. A/T: Disconnect the throttle
2013 Kia Optima L4-2.0L Turbo
1 of 13 5/29/2016 11:34 AM 2013 Kia Optima L4-2.0L Turbo Vehicle» Engine, Cooling and Exhaust» Engine» Service and Repair» Removal and Replacement Removal CAUTION: Use fender covers to avoid damaging painted
1 of 12 11/20/2016 9:32 PM
1 of 12 11/20/2016 9:32 PM Caution: After removing timing chain, do not turn crankshaft and camshaft separately, or valves will strike piston heads. Apply new engine oil to the sliding surfaces when Installing
WARNING: ALWAYS relieve fuel pressure before disconnecting any fuel related component. DO NOT allow fuel to contact engine or electrical components.
4.0L V8 - VINS [K,U] Selected Block 1990 Lexus LS 400 For Lextreme Powertrain 2020 S. Hacienda Blvd. # D Hacienda Heights California 91745 Copyright 1998 Mitchell Repair Information Company, LLC Friday,
1989 Nissan 300ZX. 3.0L V6 - VIN [H] & 3.0L V6 TURBO - VIN [C] 1989 Engines - 3.0L & 3.0L Turbo V6
![1989 Nissan 300ZX. 3.0L V6 - VIN [H] & 3.0L V6 TURBO - VIN [C] 1989 Engines - 3.0L & 3.0L Turbo V6](/thumbs/95/124411779.jpg "1989 Nissan 300ZX. 3.0L V6 - VIN [H] & 3.0L V6 TURBO - VIN [C] 1989 Engines - 3.0L & 3.0L Turbo V6")
INTAKE MANIFOLD Removal 1. Release fuel system pressure. Disconnect battery and drain cooling system. Disconnect vacuum and coolant lines attached to intake manifold and label accordingly. Remove throttle
2003 Nissan-Datsun Truck Frontier 4WD V6-3.3L (VG33E)
1 of 15 8/7/2016 2:34 PM 2003 Nissan-Datsun Truck Frontier 4WD V6-3.3L (VG33E) Vehicle» Engine, Cooling and Exhaust» Engine» Cylinder Head Assembly» Service and Repair» Removal and Installation 2 of 15
Cylinder Head Replacement
CYLINDER HEAD REPLACEMENT (EN... CYLINDER HEAD REPLACEMENT (ENGINE MECHANICAL - 1.6L) Document ID# 1430093 Cylinder Head Replacement Tools Required J 45059 Angle Meter KM-470-B Angular Torque Gauge J 42492-A
CYLINDER HEAD GASKET (2AZ-FE)
190 REPLACEMENT 1. WORK FOR PREVENTING GASOLINE FROM SPILLING OUT (See page 111 ) 2. REMOVE FRONT SUSPENSION UPPER BRACE CENTER (W/ FRONT SUSPENSION BRACE UPPER CENTER) 3. REMOVE CHAIN SUBASSY (See page
REMOVAL 7. DISCONNECT ACCELERATOR CABLE FROM THROTTLE BODY. 8. DISCONNECT HOSES (a) Remove the 2 bolts from the air intake chamber assembly.
ENGINE MECHANICAL (VZFE) EM9 REMOVAL EM1MP01 1. REMOVE ENGINE UNDER COVER. DRAIN ENGINE COOLANT. REMOVE FRONT EXHAUST PIPE (See page EM10 ). DISCONNECT HEATER HOSE. REMOVE AIR CLEANER ASSEMBLY 6. REMOVE
2012 Kia Soul L4 2.0L
2012 Kia Soul L4 2.0L Vehicle» Engine, Cooling and Exhaust» Engine» Timing Chain» Service and Repair» Repair Procedures» Part 2 Installation 1. The TDC marks of the intake and exhaust CVVT sprockets are
Lower Intake Manifold Replacement
Lower Intake Manifold Replacement Removal Procedure 1. Turn OFF all the lamps and the accessories. 2. Ensure the ignition switch is in the OFF position. 3. Disconnect the negative battery cable from the
REMOVAL 1. DRAIN ENGINE COOLANT 2. REMOVE THROTTLE BODY COVER 3. DISCONNECT TIMING BELT FROM CAMSHAFT TIM- ING PULLEYS (See page EM 14)
EM34 ENGINE MECHANICAL (2UZFE) EM11U02 REMOVAL 1. DRAIN ENGINE COOLANT 2. REMOVE THROTTLE BODY COVER 3. DISCONNECT TIMING BELT FROM CAMSHAFT TIM- ING PULLEYS (See page EM14) A02844 Be careful not to drop
2011 > G 1.6 DOHC > Language. [MDPS Type] Loosen the mounting bolts (A) and then, turn the adjusting bolt(b) clockwise in loose tension.
![2011 > G 1.6 DOHC > Language. [MDPS Type] Loosen the mounting bolts (A) and then, turn the adjusting bolt(b) clockwise in loose tension.](/thumbs/85/92293562.jpg "2011 > G 1.6 DOHC > Language. [MDPS Type] Loosen the mounting bolts (A) and then, turn the adjusting bolt(b) clockwise in loose tension.")
2011 > G 1.6 DOHC > Language Removal Engine removal is not required for this procedure. 1. Disconnect the battery negative terminal. 2. Loosen the water pump pulley bolt and the drive idler mounting bolt.
ENGINE ASSEMBLY. COMPONENTS (Part 1)
1 of 32 ENGINE ASSEMBLY COMPONENTS (Part 1) 2 of 32 COMPONENTS (Part 2) 3 of 32 COMPONENTS (Part 3) 4 of 32 COMPONENTS (Part 4) 5 of 32 COMPONENTS (Part 5) 6 of 32 COMPONENTS (Part 6) 7 of 32 COMPONENTS
2/18/2017 Cylinder Head Assembly Service and Repair, Removal and Replacement: Cylinder Head
Cylinder Head http://repair.alldata.com/alldata/article/display.action?componentid=65&itypeid=401&nonstandardid=2762152&vehicleid=47645&miles=&printfriendl 1/17 RH Splash Shield Accessory Drive Belt, Thermostat
ENGINE 6G74 3.5L-SOHC-24 VALVE
11A ENGINE General Information/Service Specifications ENGINE 6G74 3.5L-SOHC-24 VALVE GENERAL INFORMATION Items Specifications Type V-type, Over Head Camshaft Number of cylinders 6 Bore mm 93.0 Stroke mm
2002 Mustang Workshop Manual
Page 1 of 13 SECTION 303-01B: Engine 4.6L (2V) 2002 Mustang Workshop Manual REMOVAL Procedure revision date: 01/02/2003 Cylinder Heads Special Tool(s) Remover, Crankshaft Vibration Damper 303-009 (T58P-6316-D)
REMOVAL & INSTALLATION
REMOVAL & INSTALLATION NOTE: For reassembly reference, label all electrical connectors, vacuum hoses and fuel lines before removal. Also place mating marks on engine hood and other major assemblies before
7. Remove the starter motor. Refer to Starter Motor Replacement (2.2L) or Starter Motor Replacement (4.3L).
1 of 9 1/5/2013 6:40 PM Removal Procedure 1. Disconnect the battery negative cable. Refer to Battery Replacement. 2. Remove the hood. Refer to Hood Replacement. 3. If the vehicle is equipped with a manual
2005 Hyundai Tucson LX. On some models, engine is equipped with a timing belt and timing chain. Inspect timing chain when replacing timing belt.
TIMING BELT NOTE: On some models, engine is equipped with a timing belt and timing chain. Inspect timing chain when replacing timing belt. Removal 1. Remove the engine cover. See Fig. 1. 2. Remove right
2002 Explorer Sport/Sport Trac Workshop Manual
Page 1 of 17 SECTION 303-01: Engine 4.0L Single Overhead Camshaft (SOHC) IN-VEHICLE REPAIR Procedure revision date: 07/13/2005 Cylinder Head Special Tool(s) Spark Plug Wire Remover 303-106 (T74P-6666-A)
Cylinder Head Removal
2006 Odyssey Cylinder Head Removal Report a problem with this article NOTE: Use fender covers to avoid damaging painted surfaces. To avoid damaging the wires and terminals, unplug the wiring connectors
Fastener Tightening Specifications Specification
2008 G6 Applies to: 3.5L Report a problem with this article Fastener Tightening s A/C Compressor Bracket Bolt Camshaft Position Actuator Assembly Bolt 16 Y 12 lb ft Camshaft Position Actuator Magnet Bolt
DISASSEMBLY Procedure revision date: 11/22/2001
Page 1 of 31 Evan Groenke From: Daniel Lelovic [dlelovic@rogers.com] Sent: May 8, 2005 12:06 PM To: 'Evan Groenke' Subject: 2.5 L Engine Disassembly SECTION 303-01B: Engine 2.5L 2000 Contour/Mystique Workshop
Zoom and Print Options
Vehicle» Engine, Cooling and Exhaust» Engine» Service and Repair» Removal and Replacement» Engine Replacement Engine Replacement ^ Tools Required - J 38185 Hose Clamp Pliers Removal Procedure 1. Remove
Intake Manifold: Service and Repair Removal
1992 Toyota Truck Pickup 2WD V6-180.5 2959cc 3.0L SOHC (3VZ-E) Copyright 2013, ALLDATA 10.52 Page 1 Intake Manifold: Service and Repair Removal NOTE: If removing and later reinstalling the fluid coupling
VALVE CLEARANCE (K3-VE)
ENGINE MECHANICAL VALVE CLEARANCE (K3-VE) 25 ENGINE MECHANICAL VALVE CLEARANCE (K3-VE) INSPECTION 1. DISCONNECT NEGATIVE BATTERY TERMINAL (See page RS-164.) 2. ROVE ENGINE UNDER COVER 3. DRAIN ENGINE COOLANT
1991 Volkswagen Vanagon Syncro
corner of radiator. See Fig. 1. Fig. 1: Bleeding Cooling System 2. Open bleeder valve in engine compartment (turn counterclockwise). See Fig. 1. Fill expansion tank until full. Start and run engine at
2/17/2017 Timing Belt Service and Repair, Removal and Replacement
http://repair.alldata.com/alldata/article/display.action?componentid=64&itypeid=401&nonstandardid=0&vehicleid=39554&miles=&printfriendly=com 1/22 http://repair.alldata.com/alldata/article/display.action?componentid=64&itypeid=401&nonstandardid=0&vehicleid=39554&miles=&printfriendly=com
General Information SPECIFICATIONS. Description Specifications Limit. General. V-type, DOHC. Number of cylinder mm(3.4134in.) 75mm(2.9528in.
General Information SPECIFICATIONS General Type Description Specifications Limit Number of cylinder 6 Bore Stroke Total displacement V-type, DOHC 86.7mm(3.4134in.) 75mm(2.9528in.) 2,656cc Compression ratio
REMOVAL. Fig Sized for Print
ALLDATA Online - 2000 Dodge Truck Grand Caravan FWD V6-3.3L VIN R - Intake M... Page 1 of 10 REMOVAL 1. Remove windshield wiper module. 2. Perform fuel system pressure release procedure (before attempting
DISASSEMBLY. Engine. CAUTION: Remove the cylinder heads before removing the crankshaft. Failure to do so can result in engine damage.
303-01A-1 DISASSEMBLY Engine Special Tool(s) Remover, Crankshaft Vibration Damper 303-101 (T74P-3616-A) Special Tool(s) Crankshaft Socket 303-674 303-01A-1 Remover, Crankshaft Vibration Damper 303-773
Intake Manifold Removal and Installation
2004 Element Intake Manifold Removal and Installation Exploded View Removal Report a problem with this article 1. Disconnect the intake air temperature (IAT) sensor connector (A). 2. Remove the vacuum
2004 Nissan/Datsun Truck Quest Mini Van 3.5L SFI DOHC 6cyl Repair Guides Engin...
Page 1 of 10 SAVE 20% ON ONLINE SHIP-TO-HOME ORDERS OF $100 OR MORE. Use Code: MOM20 See Details Nissan Quest 2001-02 and 2004-06 REMOVAL & INSTALLATION Timing Chain Cover Removal & Installation 3.5L Engine
2002 Escape Workshop Manual
SECTION 303-01A: Engine 2.0L Zetec 2002 Escape Workshop Manual IN-VEHICLE REPAIR Procedure revision date: 10/25/2004 Timing Belt Special Tool(s) Crankshaft TDC Timing Peg 303-574 (T97P-6000-A) Camshaft
2003 Taurus/Sable Workshop Manual
Page 1 of 24 SECTION 303-01A: Engine 3.0L (2V) ASSEMBLY 2003 Taurus/Sable Workshop Manual Engine Special Tool(s) Piston Ring Compressor 303- D032 (D81L-6002-C) Camshaft Bearing Set 303-017 (T65L-6250-A)
GENERAL SPECIFICATIONS
2007 ENGINE Engine Mechanical System (G6EA-GSL 2.7) - Santa Fe GENERAL SPECIFICATIONS GENERAL SPECIFICATIONS Description Specifications Limit General Type V-type, DOHC Number of cylinder 6 Bore 86.7mm
2003 Toyota Truck Highlander 2WD V6-3.0L (1MZ-FE) Copyright 2013, ALLDATA Page 1
2003 Toyota Truck Highlander 2WD V6-3.0L (1MZ-FE) Copyright 2013, ALLDATA 10.52 Page 1 Timing Belt: Service and Repair TIMING BELT REPLACEMENT 1. REMOVE FRONT WHEEL RH 2. REMOVE FRONT FENDER APRON SEAL
TIMING BELT COMPONENTS EM 15
ENGINE MECHANICAL COMPONENTS EM15 EM16 ENGINE MECHANICAL COMPONENTS (Cont d) ENGINE MECHANICAL EM17 REMOVAL OF (See pages EM15 and 16) 1. DISCONNECT CABLE FROM NEGATIVE TERMINAL OF BATTERY CAUTION: Work
NOTE: Do not disassemble upper intake manifold from lower intake manifold unless replacement of one of the components is necessary.
Fig. 2: Lower Intake Manifold Bolt Tightening Sequence INTAKE MANIFOLD (UPPER) NOTE: Do not disassemble upper intake manifold from lower intake manifold unless replacement of one of the components is necessary.
10/20/ Ford E 250 Engine Mechanical > Engine, 4.6L and 5.4L > IN VEHICLE REPAIR > Intake Manifold 5.4L
2005 Ford E 250 : Engine Mechanical > Engine, 4.6L and 5.4L > IN VEHICLE REPAIR > Intake Manifold 5.4L Intake Manifold 5.4L Listen SECTION 303 01A: Engine 4.6L and 5.4L 2005 E Series Workshop Manual IN
Page 1 of 8 SECTION 303-01A: Engine 2.3L 2002 Ranger Workshop Manual IN-VEHICLE REPAIR Procedure revision date: 10/20/2004 Intake Manifold Removal 1. Remove the accelerator control snow shield. 2. Remove
1999 Nissan Altima GLE
TIMING CHAIN CAUTION: If cylinder head is installed and timing chain is disconnected, DO NOT rotate camshaft or crankshaft; valves will contact pistons, resulting in bent valves. NOTE: Following procedure
A: ENGINE CONTROL MODULE (ECM) I/O SIGNAL FOR MT VEHICLES. Signal (V) Ignition SW ON (Engine OFF) B B B
5. Specified Data A: ENGINE CONTROL MODULE (ECM) I/O SIGNAL FOR MT VEHICLES B2M2267A Crankshaft Camshaft Throttle Rear oxygen Front oxygen (A/F) heater Rear oxygen heater Engine coolant temperature Signal
1991 Nissan 240SX. 2.4L 4-CYL - VINS [F,M,S] 1991 ENGINES Nissan 2.4L 4-Cylinder
![1991 Nissan 240SX. 2.4L 4-CYL - VINS [F,M,S] 1991 ENGINES Nissan 2.4L 4-Cylinder](/thumbs/95/123571962.jpg "1991 Nissan 240SX. 2.4L 4-CYL - VINS [F,M,S] 1991 ENGINES Nissan 2.4L 4-Cylinder")
NOTE: Use illustration for component reference. See Fig. 7. 1. Remove spark plug wires. Set No. 1 piston at TDC on its compression stroke. Remove vacuum hoses, electrical harnesses, connectors, and harness
EG 18 ENGINE MECHANICAL TIMING BELT EG5EK 01 COMPONENTS FOR REMOVAL AND INSTALLATION
EG18 ENGINE TIMING BELT COMPONENTS FOR REMOVAL AND INSTALLATION EG5EK01 ENGINE EG19 EG20 ENGINE ENGINE EG21 EG22 ENGINE TIMING BELT REMOVAL EG5G101 1. REMOVE OIL PAN PROTECTOR 2. REMOVE ENGINE UNDER COVER
COMPONENT LOCATOR > DISASSEMBLED VIEWS
Page 1 of 45 2006 Pontiac Grand Prix 3.8L Eng Base Service Manual: ENGINE MECHANICAL - 3.8L COMPONENT LOCATOR > DISASSEMBLED VIEWS Fig 1: Engine Block Component Views Callout Component Name 100 Engine
Mazda3 - Workshop Manual - Engine
Page 1 of 18 2005 - Mazda3 - Workshop Manual - Engine TIMING CHAIN REMOVAL/INSTALLATION WARNING: Fuel vapor is hazardous. It can very easily ignite, causing serious injury and damage. Always keep sparks
Service Bulletin TSX: Sticking Rings Resulting in Unusually High Engine Oil Consumption
Applies To: 2009 10 TSX L4 with M/T ALL Service Bulletin 13-006 February 22, 2013 2009 10 TSX: Sticking Rings Resulting in Unusually High Engine Oil Consumption SYMPTOM The engine oil level is low on the
Disconnect the breather tube from the air cleaner outlet duct.
Disconnect the breather tube from the air cleaner outlet duct. Disconnect the IAT sensor harness connector. Remove the air cleaner outlet duct retaining wingnut. Separate the air cleaner outlet duct from
INSTALLATION EM 8 1NZ-FE ENGINE MECHANICAL DRIVE BELT INCORRECT CORRECT. Generator Vehicle Front A077960E03. Adjusting Bar. Bolt A. Bolt B.
8 CORRECT Adjusting Bar 1NZ-FE ENGINE MECHANICAL DRIVE BELT INCORRECT Generator Vehicle Front A077960E03 INSTALLATION 1. INSTALL VANE PUMP V BELT (a) Temporarily install the belt on each pulley. 2. INSTALL
2000 Nissan Altima SE
Removal 1. Release fuel pressure. See FUEL PRESSURE RELEASE. Drain coolant from radiator and cylinder block. Drain engine oil. Disconnect all necessary coolant hoses, electrical connectors, vacuum hoses,
2005 Toyota Truck RAV4 2WD L4 2.4L (2AZ FE)
2005 Toyota Truck RAV4 2WD L4 2.4L (2AZ FE) Vehicle» Engine, Cooling and Exhaust» Engine» Timing Chain» Service and Repair TIMING CHAIN TIMING CHAIN http://alldatapro.com/alldata/pro~v440713400~c39519~r0~od~n/0/108596970/110859775/110859788/110859790/34853741/100411974/34853743/56492475
IN-VEHICLE REPAIR. Cylinder Head. Special Tool(s) Timing Tool, Crankshaft TDC (T97T-6303-A) or. Special Tool(s) equivalent
303-01A-1 IN-VEHICLE REPAIR Cylinder Head Special Tool(s) Torque Wrench Extension 303-575 (T97T-6256-F) or equivalent Special Tool(s) 303-01A-1 Timing Tool, Crankshaft TDC 303-573 (T97T-6303-A) or equivalent
11A-1 ENGINE CONTENTS
11A-1 ENGINE CONTENTS ENGINE ENGINE ... 11A... 11B 11A-2 ENGINE CONTENTS GENERAL... 3 Outline of Changes... 3 GENERAL INFORMATION... 3 SERVICE SPECIFICATIONS... 3 SEALANT... 3 SPECIAL
Intake Components 1117
Item Part Number Description 1 W705654 Bolt 2 N807309 Bolt (2 req'd) 3 9F460 Bracket 4 N807071 Bolt (5 req'd) 5 9A448 Intake manifold (upper) 6 9E498 Vacuum harness 7 9F792 Fuel injection supply manifold
2000 Toyota Truck Tundra. Timing Belt: Service and Repair
Timing Belt: Service and Repair REMOVAL 1. REMOVE ENGINE UNDER COVER 2. DRAIN ENGINE COOLANT 3. REMOVE RADIATOR ASSEMBLY 4. REMOVE THROTTLE BODY COVER 5. REMOVE INTAKE AIR CONNECTOR ASSEMBLY 6. REMOVE
2003 ACCORD - Intake Manifold Removal and Installation
2003 ACCORD - Intake Manifold Removal and Installation Exploded View '06-07 Models Removal ('03-05 Models) 1. Disconnect the intake air temperature (IAT) sensor connector (A). 2. Remove the vacuum hose
1983 BMW 320i. 1.8L 4-CYL 1983 Engines - 1.8L 4-Cylinder Engines - 1.8L 4-Cylinder
ENGINE IDENTIFICATION 1.8L 4-CYL 1983 Engines - 1.8L 4-Cylinder For engine repair procedures not covered in this article, see ENGINE OVERHAUL PROCEDURES - GENERAL INFORMATION article in the GENERAL INFORMATION
26/01/2017 3GR-FSE ENGINE MECHANICAL: ENGINE UNIT: DISASSEMBLY; 2006 MY GS300 [01/ ]
![26/01/2017 3GR-FSE ENGINE MECHANICAL: ENGINE UNIT: DISASSEMBLY; 2006 MY GS300 [01/ ]](/thumbs/85/92233007.jpg "26/01/2017 3GR-FSE ENGINE MECHANICAL: ENGINE UNIT: DISASSEMBLY; 2006 MY GS300 [01/ ]")
Last Modified: 8-24-2016 6.6 A Doc ID: RM000000T4X000X Model Year Start: 2006 Model: GS300 Prod Date Range: [01/2005 - ] Title: 3GR-FSE ENGINE MECHANICAL: ENGINE UNIT: DISASSEMBLY; 2006 MY GS300 [01/2005
2.0L 4-CYL & 2.0L 4-CYL TURBO - VIN [S]
![2.0L 4-CYL & 2.0L 4-CYL TURBO - VIN [S]](/thumbs/81/82864711.jpg "2.0L 4-CYL & 2.0L 4-CYL TURBO - VIN [S]")
2.0L 4-CYL & 2.0L 4-CYL TURBO - VIN [S] 1988 Toyota Celica 1988 TOYOTA ENGINES 2.0L & 2.0L Turbo 4-Cylinder Celica * PLEASE READ THIS FIRST * NOTE: For engine repair procedures not covered in this article,
Page 1 of 9 SECTION 303-01B: Engine 2.0L SPI 2002 Focus Workshop Manual ASSEMBLY Procedure revision date: 12/14/2000 Engine Special Tool(s) Crankshaft Rear Seal Pilot 303-329 (T88P-6701-B2) Crankshaft
DISASSEMBLY AND REASSEMBLY
24 01 DISASSEMBLY AND REASSEMBLY COMPONENTS AND SPECIAL TOOLS Injector Puller Y99220072B Glow Plug Wrench Y99220132B Fuel Pipe Wrench Sealing Caps 665 995 5844 Injector Copper Washer Puller Y99220022B
REMOVAL & INSTALLATION
REMOVAL & INSTALLATION CAUTION: This application is an interference engine. Do not rotate camshaft or crankshaft when timing belt is removed, or engine damage may occur. TIMING BELT Removal 1. Raise and
Cylinder head, removing and
Page 1 of 35 15-2 Cylinder head, removing and installing Note: Replace cylinder head bolts. Always replace self-locking nuts, bolts as well as gaskets and O-rings. After installing a replacement cylinder
Page 1 of 21 303-01C Engine 5.4L (3V) 2009 F-150 REMOVAL Procedure revision date: 03/26/2009 Cylinder Head Special Tool(s) 3 Jaw Puller 303-D121 or equivalent Compressor, Valve Spring 303-1039 Holding
ALLDATA Online Chevy Truck S10/T10 Blazer 2WD V6-4.3L VIN W - Intake... Intake Manifold Replacement (Upper)
ALLDATA Online - 2001 Chevy Truck S10/T10 Blazer 2WD V6-4.3L VIN W - Intake... Page 1 of 21 Home Account Contact ALLDATA Log Out Help PAUL REDEHOFT Select Vehicle New TSBs Technician's Reference Component
2001 Lincoln LS Workshop Manual
Page 1 of 10 SECTION 303-01B: Engine 3.9L 2001 Lincoln LS Workshop Manual IN-VEHICLE REPAIR Procedure revision date: 05/16/2000 Intake Manifold Removal 1. Disconnect the battery ground cable. For additional
Engine Cylinder Head Installation
Engine Cylinder Head Installation Important: Install the cylinder head without the camshafts. 1. Install the engine cylinder head to the engine block. 2. Install the AIR pump bolt and fir tree fastener
MANUFACTURER'S SUGGESTED SCHEDULED MAINTENANCE
1. Disconnect negative battery cable. Drain cooling system. Remove front strut bar and strut brackets, if equipped. 2. Disconnect Intake Air Temperature (IAT) sensor harness connector. Remove air cleaner
2000 Econoline Workshop Manual. 3. Install the upper intake manifold. 2. NOTE: Tighten the bolts in two stages.
2. NOTE: Tighten the bolts in two stages. Tighten the bolts in the sequence shown. Stage 1: Tighten to 2 Nm (18 lb-in). Stage 2: Tighten to 10 Nm (89 lb-in). 3. Install the upper intake manifold. Position
Page 1 of 25. Service and Repair REMOVAL SIZED FOR PRINT. Related Components
Page 1 of 25 Service and Repair REMOVAL Related Components Page 2 of 25 1ZZ-FE Page 3 of 25 2ZZ-GE 1. REMOVE UPPER FRONT FENDER APRON SEAL AND UPPER RADIATOR SUPPORT SEAL 2. DRAIN ENGINE COOLANT 3. REMOVE
SECTION 6A ENGINE MECHANICAL (G10, 1-CAM 6-VALVES ENGINE)
ENGINE MECHANICAL (G10, 1-CAM 6-VALVES ENGINE) 6A-1 SECTION 6A ENGINE MECHANICAL (G10, 1-CAM 6-VALVES ENGINE) WARNING: For vehicles equipped with Supplemental Restraint (Air Bag) System: Service on and
IN-VEHICLE SERVICE. Engine Components
file://c:\tso\tsocache\vdtom_5368\svk~us~en~file=svk31a14.htm~gen~ref.htm Page 1 of 10 Section 03-01A: Engine, 2.3L I-4 IN-VEHICLE SERVICE 1997 Ranger Workshop Manual Engine Components The views shown
Service Bulletin
Service Bulletin 12-087 Applies To: See VEHICLES AFFECTED August 17, 2013 2008 11 Accord L4: Sticking Rings Resulting in Unusually High Engine Oil Consumption (Supersedes 12-087, dated April 30, 2013,
Before performing any on-vehicle adjustments to fuel or ignition systems, ensure engine mechanical condition is okay.
Page 1 of 11 ARTICLE BEGINNING INTRODUCTION Introduction information not applicable. ENGINE MECHANICAL Before performing any on-vehicle adjustments to fuel or ignition systems, ensure engine mechanical
1 of 12 10/5/2015 8:11 AM
1 of 12 10/5/2015 8:11 AM REMOVAL 1. Perform the fuel pressure release procedure See: Fuel Pressure Release > Procedures > Fuel System Pressure Release Procedure. 2. Recover the refrigerant from the refrigerant
ASSEMBLY Procedure revision date: 11/22/2001
Page 1 of 39 Evan Groenke From: Daniel Lelovic [dlelovic@rogers.com] Sent: May 8, 2005 12:08 PM To: 'Evan Groenke' Subject: 2.5L Engine Re-assembly SECTION 303-01B: Engine 2.5L 2000 Contour/Mystique Workshop
GROUP 11C 11C-1 CONTENTS GENERAL DESCRIPTION... 11C-2 ENGINE DIAGNOSIS... 11C-2 CRANKSHAFT FRONT OIL SEAL... 11C-30 SPECIAL TOOLS...
11C-1 GROUP 11C CONTENTS GENERAL DESCRIPTION 11C-2 ENGINE DIAGNOSIS 11C-2 SPECIAL TOOLS 11C-3 ON VEHICLE SERVICE 11C-5 DRIVE BELT TENSION CHECK AND ADJUSTMENT 11C-5 IGNITION TIMING CHECK 11C-5 IDLE MIXTURE
5. Engine Control Module (ECM) I/O Signal S008526
5. Engine Control Module (ECM) I/O Signal S008526 A: ELECTRICAL SPECIFICATION S008526A08 1. MT VEHICLES S008526A0801 B2M2267A Crankshaft Camshaft Throttle Rear oxygen Front oxygen (A/F) heater Rear oxygen
1992 Toyota Cressida
Monday, May 16, 2016 5:32:47 PM Page 13 2005 Mitchell Repair Information Company, LLC. Fig. 7: Exploded View Of Typical Cylinder Head & Components Fig. 8: Cylinder Head Bolt Removal Sequence Monday, May
Vehicle Level Engine, Cooling and Exhaust Engine Intake Manifold Service and Repair. Service and Repair
Page 1 of 11 Home Account Contact ALLDATA Log Out Help BILL SEIDLES MITSUBISHI Select Vehicle New TSBs Technician's Reference Component Search: OK 2005 Suzuki Verona L6-2.5L Conversion Calculator Vehicle
ENGINE MECHANICAL <3.0L>
11C-1 GROUP 11C ENGINE MECHANICAL CONTENTS GENERAL DESCRIPTION......... 11C-2 ENGINE DIAGNOSIS............. 11C-2 SPECIAL TOOLS................ 11C-3 ON VEHICLE SERVICE........... 11C-5 DRIVE BELT
TIMING CHAIN COMPONENTS
h Page 1 of 52 TIMING CHAIN COMPONENTS ht Page 2 of 52 Fig. 24: Displaying Timing Chain Components (1 Of 2) Page 3 of 52 Fig. 25: Displaying Timing Chain Components (2 Of 2) Page 4 of 52 REMOVAL NOTE:
Page 1 of 6 Section 03-01C: Engine, 7.5L MFI 1996 Bronco/F-Series Workshop Manual IN-VEHICLE SERVICE Procedure revision date: 06/19/2000 Cylinder Heads Removal SPECIAL SERVICE TOOL(S) REQUIRED Description
5.7L V Chevrolet Camaro * PLEASE READ THIS FIRST * ENGINE IDENTIFICATION VEHICLE IDENTIFICATION NUMBER (VIN) ADJUSTMENTS
5.7L V8 2001 Chevrolet Camaro 2000-01 ENGINES General Motors 5.7L V8 Chevrolet; Camaro Pontiac; Firebird * PLEASE READ THIS FIRST * NOTE: For engine repair procedures not covered in this article, see ENGINE
Rocker Lever Housing
003-013 Rocker Lever Housing Preparatory Steps Disconnect the air piping from the intake manifold. Remove the rocker lever cover. Refer to Procedure 003-011 in Section 3. Remove the engine brakes, if applicable,
REMOVAL & INSTALLATION
REMOVAL & INSTALLATION TIMING BELT Removal 1. Disconnect negative battery cable. Rotate engine clockwise and position cylinder No. 1 on TDC of compression stroke. Ensure "O" mark on crankshaft pulley aligns
Cylinder Head, Remove and Install (Z 22 SE)
Page 1 of 29 Cylinder Head, Remove and Install (Z 22 SE) Remove 1. Open the bonnet. 2. Disconnect the battery. 3. Open the engine cover (1). 4. Detach the engine cover. 6 bolts (2) and (3) 5. Release the
1GR-FE ENGINE MECHANICAL: TIMING CHAIN: INSTALLATION (2007 4Runner) Model Year: 2007 Model: 4Runner Doc ID: RM WS002X
Last Modified: 4-26-2007 Service Category: Engine/Hybrid System 1.6 A Section: Engine Mechanical Model Year: 2007 Model: 4Runner Doc ID: RM0000029WS002X Title: 1GR-FE ENGINE MECHANICAL: TIMING CHAIN: INSTALLATION
Service and Repair. a. Remove the 2 nuts and 2 upper radiator support. b. Lift out the radiator and cooling fan assembly.
Service and Repair REPLACEMENT 1. SEPARATE BATTERY NEGATIVE TERMINAL 2. REMOVE AIR CLEANER INLET NO.1 3. DRAIN ENGINE COOLANT 4. REMOVE V-BANK COVER 5. REMOVE INTAKE AIR CONNECTOR PIPE 6. REMOVE ENGINE
DISASSEMBLED VIEWS. Disassembled Views. Engine Covers and Component Assemblies (1 of 2) (LF1, LFW or LFX)
2012 Cadillac CTS Wagon AWD V6-3.0L Vehicle > Engine, Cooling and Exhaust > Engine > Locations > Components DISASSEMBLED VIEWS Disassembled Views Engine Covers and Component Assemblies (1 of 2) (LF1, LFW
OVERHAUL 1. REMOVE OIL FILLER CAP SUB ASSY. 2. REMOVE CYLINDER HEAD COVER SUB ASSY (a) Remove the 10 bolts, 2 nuts, cylinder head cover and gasket.
144 ENGINE MECHANICAL OVERHAUL 1. REMOVE OIL FILLER CAP SUBASSY 1410H01 2. REMOVE CYLINDER HEAD COVER SUBASSY (a) Remove the 10 bolts, 2 nuts, cylinder head cover and gasket. A11090 3. REMOVE CAMSHAFT
EG-34 ENGINE MECHANICAL TIMING BELT COMPONENTS FOR REMOVAL AND INSTALLATION
EG34 TIMING BELT COMPONENTS FOR REMOVAL AND INSTALLATION EG35 TIMING BELT REMOVAL (See Components for Removal and Installation) 1. DISCONNECT NEGATIVE TERMINAL CABLE FROM BATTERY CAUTION: Work must be
Engine Dismantle and Assemble ( )
Engine Dismantle and Assemble ( 34 8) Special Tools 5 053 Slide hammer 47 Vibration damper remover 47 5053 00 Splined head socket, cylinder head bolts 87 Mounting stand with geared drive 00 059C Installer
Audi > B4 > Liter V6 2V Engine Mechanical, Engine Code(s): AAH, AFC 10 Engine Assembly
Audi > B4 > 1993 1995 2.8 Liter V6 2V Engine Mechanical, Engine Code(s): AAH, AFC 10 Engine Assembly Removing The engine is removed from above, after being separated from the transmission. Note: All tie