ALLDATA Online Chevy Truck S10/T10 Blazer 2WD V6-4.3L VIN W - Intake... Intake Manifold Replacement (Upper)
|
|
- Roland Young
- 5 years ago
- Views:
Transcription
1 ALLDATA Online Chevy Truck S10/T10 Blazer 2WD V6-4.3L VIN W - Intake... Page 1 of 21 Home Account Contact ALLDATA Log Out Help PAUL REDEHOFT Select Vehicle New TSBs Technician's Reference Component Search: OK 2001 Chevy Truck S10/T10 Blazer 2WD V6-4.3L VIN W Conversion Calculator Vehicle Level Engine, Cooling and Exhaust Engine Intake Manifold Service and Repair Intake Manifold Replacement (Upper) Intake Manifold Replacement (Upper) Notes Intake Manifold Replacement - Upper Removal Procedure Important: The upper intake does not have to be removed to remove the lower intake manifold. 1. Disconnect the breather tube at the air cleaner outlet duct.
2 ALLDATA Online Chevy Truck S10/T10 Blazer 2WD V6-4.3L VIN W - Intake... Page 2 of Remove the air cleaner outlet duct retaining wingnut. 3. Disconnect the IAT sensor harness connector.
3 ALLDATA Online Chevy Truck S10/T10 Blazer 2WD V6-4.3L VIN W - Intake... Page 3 of Remove the air cleaner outlet duct from the throttle body. 5. Disconnect the accelerator cable from the throttle body.
4 ALLDATA Online Chevy Truck S10/T10 Blazer 2WD V6-4.3L VIN W - Intake... Page 4 of Remove the accelerator cable from the accelerator control cable bracket. 7. Disconnect the cruise control cable, if equipped from the throttle shaft and the accelerator cable bracket. 8. Disconnect the vacuum hose from the intake manifold for the vacuum tank. 9. Remove the power brake booster vacuum hose.
5 ALLDATA Online Chevy Truck S10/T10 Blazer 2WD V6-4.3L VIN W - Intake... Page 5 of Disconnect the following electrical connectors: The A/C compressor clutch (1) The A/C compressor cutoff switch (5), if equipped The Throttle Position (TP) sensor (2) The Idle Air Control (IAC) motor (3) 11. Disconnect the following electrical connectors: The fuel meter body assembly (1) The Manifold Absolute Pressure (MAP) sensor(3) The EVAP canister purge solenoid valve (2)
6 ALLDATA Online Chevy Truck S10/T10 Blazer 2WD V6-4.3L VIN W - Intake... Page 6 of Remove the engine wire harness clip from the accelerator cable bracket. 13. Move the engine wiring harness aside. 14. Remove the accelerator cable bracket from the throttle body and the intake manifold. 15. Remove the accelerator and cruise control cable bracket from the throttle body. Leave the accelerator and cruise control cables on the bracket.
7 ALLDATA Online Chevy Truck S10/T10 Blazer 2WD V6-4.3L VIN W - Intake... Page 7 of Remove the PCV valve hose assembly from the intake manifold and the valve rocker arm cover. 17. Remove the bracket for the engine wiring harness from the intake manifold stud. 18. Remove the fuel lines from the fuel meter body assembly. 19. Remove the EVAP canister purge solenoid valve.
8 ALLDATA Online Chevy Truck S10/T10 Blazer 2WD V6-4.3L VIN W - Intake... Page 8 of Remove the studs for the upper intake manifold, 21. Remove the upper intake manifold. 22. Remove the upper intake manifold gasket from the groove. 23. Discard the gasket.
9 ALLDATA Online Chevy Truck S10/T10 Blazer 2WD V6-4.3L VIN W - Intake... Page 9 of Remove the seal from the fuel meter body assembly. 25. Discard the seal. Important: Do not immerse the assembled upper intake manifold in cleaning solvent. 26. Clean all sealing surfaces and the inside of the upper intake manifold with a shop towel and cleaning solvent. 27. Inspect the upper intake manifold for the following: Cracks or other damage to the exterior Cracking or damage to the gasket grooves Loose or damaged bolt hole thread inserts Damage to the throttle body mounting surface
10 Page 10 of If replacing the upper intake manifold, turn and remove the power brake booster vacuum tube fitting from the upper intake manifold. 29. Remove and discard the seal. 30. If replacing the upper intake manifold, turn and remove the PCV valve cover from the upper intake manifold. 31. Remove and discard the seal. 32. Remove the throttle body if replacing the upper intake manifold. 33. Remove the MAP sensor if replacing the upper intake manifold. Installation Procedure
11 Page 11 of Install the throttle body, if removed. 2. Install the MAP sensor, if removed. 3. Install the PCV valve cover, if removed, using the following procedure: 3.1. Install a NEW seal (O-ring) on the PCV valve cover Lubricate the seal with clean engine oil Install the PCV valve cover in the upper intake manifold Turn and lock the PCV valve cover in position. 4. Install the power brake booster vacuum tube fitting, if removed, using the following procedure: 4.1. Install a NEW seal (O-ring) on the power brake booster vacuum tube fitting Lubricate the seal with clean engine oil Install the power brake booster vacuum tube fitting in the upper intake manifold Turn and lock the power brake booster vacuum tube fitting in position.
12 Page 12 of Install a NEW seal on the fuel meter body assembly. 6. Lubricate the seal with clean engine oil. 7. Install a NEW upper intake manifold to lower intake manifold gasket in the groove of the upper intake manifold.
13 Page 13 of Install the upper intake manifold onto the lower intake manifold. 9. If reusing the fasteners, apply threadlock GM P/N or equivalent to the threads of the upper intake manifold attaching bolts. Notice: Refer to Fastener Notice in Service Precautions. 10. Install the upper intake manifold attaching studs Tighten the upper intake manifold attaching studs on the first pass to 5 Nm (44 inch lbs.) Tighten the upper intake manifold attaching studs on the final pass to 9 Nm (80 inch lbs.). 11. Install the fuel lines to the fuel meter body assembly. 12. Install the EVAP canister purge solenoid valve.
14 Page 14 of Install the bracket for the engine wiring harness on the lower intake manifold stud. 14. Install the engine wiring harness bracket nut. Tighten the engine wiring harness bracket nut to 12 Nm (106 inch lbs.). 15. Install the accelerator and cruise control cable bracket to the throttle body. 16. Install the accelerator and cruise control cable bracket nuts. Tighten the accelerator and cruise control cable bracket nuts to 9 Nm (80 inch lbs.).
15 Page 15 of Install the accelerator control cable bracket to the throttle body and the intake manifold. Tighten the accelerator control cable bracket studs and nuts to 12 Nm (106 inch lbs.). 18. Connect the PCV valve hose assembly to the intake manifold and the valve rocker arm cover.
16 Page 16 of Position the engine wiring harness. 20. Install the wire harness clip to the accelerator cable bracket. 21. Connect the following electrical connectors: The fuel meter body assembly (1) The Manifold Absolute Pressure (MAP) sensor(3) The EVAP canister purge solenoid valve (2) 22. Connect the following electrical connectors: The A/C compressor clutch (1) The A/C compressor cutoff switch (5), if equipped
17 Page 17 of 21 The Throttle Position (TP) sensor (2) The Idle Air Control (IAC) motor (3) 23. Connect the vacuum hose from the vacuum tank to the intake manifold. 24. Install the power brake booster vacuum hose to the intake manifold. 25. Install the cruise control cable, if equipped to the throttle shaft and the bracket. 26. Install the accelerator cable onto the throttle body.
18 Page 18 of 21
19 Page 19 of Wrap the cable in between the finger of the hook tab and the pulley wall. Make sure that the cable is fully seated in the pulley groove. The cable must not lie outside of the hook tab. 28. Install the accelerator cable to the accelerator cable control bracket. Notice: Handle the MAF sensor carefully.
20 Page 20 of 21 Do not drop the MAF sensor in order to prevent damage to the MAF sensor. Do not damage the screen located on the air inlet end of the MAF. Do not touch the sensing elements. Do not allow solvents and lubricants to come in contact with the sensing elements. Use a small amount of a soap based solution in order to aid in the installation. 29. Install air cleaner outlet duct to throttle body. 30. Install air cleaner outlet duct to MAF sensor. Tighten the hose clamp to 4 Nm (32 inch lbs.). 31. Connect the IAT sensor harness connector.
21 Page 21 of Install the air cleaner outlet duct retaining wingnut. Tighten the wingnut to 2 Nm (18 inch lbs.). 33. Connect the breather tube to the air cleaner outlet duct ALLDATA LLC. All rights reserved. Terms of Use
ALLDATA Online Chevy Truck S10/T10 P/U 2WD L4-2.2L VIN 4 - Service and... Page 1 of 12. Service and Repair
ALLDATA Online - 2000 Chevy Truck S10/T10 P/U 2WD L4-2.2L VIN 4 - Service and... Page 1 of 12 Home Account Contact ALLDATA Log Out Help PAUL REDEHOFT Select Vehicle New TSBs Technician's Reference Component
More informationDisconnect the breather tube from the air cleaner outlet duct.
Disconnect the breather tube from the air cleaner outlet duct. Disconnect the IAT sensor harness connector. Remove the air cleaner outlet duct retaining wingnut. Separate the air cleaner outlet duct from
More informationIntake Manifold Replacement
Page 1 of 14 2004 Chevrolet TrailBlazer - 4WD Bravada, Envoy, Rainier, TrailBlazer (VIN S/T) Service Manual Engine Engine Mechanical - 4.8L, 5.3L, and 6.0L Repair Instructions - On Vehicle Document ID:
More informationIntake Manifold Replacement
Document ID# 738735 2002 Chevrolet Chevy Suburban - 4WD Print Intake Manifold Replacement Removal Procedure Important: The intake manifold, throttle body, fuel rail, and injectors may
More informationLower Intake Manifold Replacement
Lower Intake Manifold Replacement Removal Procedure 1. Turn OFF all the lamps and the accessories. 2. Ensure the ignition switch is in the OFF position. 3. Disconnect the negative battery cable from the
More informationIntake Manifold Replacement
ALLDATA Online - 2001 Cadillac DeVille V8-4.6L VIN 9 - Intake Manifold Replacement Page 1 of 15 Home Account Contact ALLDATA Log Out Help DAN GRIMWOOD DAN GRIMWOOD00002 Select Vehicle New TSBs Technician's
More informationZoom and Print Options
Vehicle» Engine, Cooling and Exhaust» Engine» Service and Repair» Removal and Replacement» Engine Replacement Engine Replacement ^ Tools Required - J 38185 Hose Clamp Pliers Removal Procedure 1. Remove
More information2. Disconnect the accelerator control cable and the cruise control cable from the throttle body. 3. Disconnect the vacuum hose from the throttle body.
2002 Silverado K 4WD Applies to: 4.8L, 5.3L, and 6.0L Report a problem with this article Removal Procedure 1. Remove the air intake duct. Refer to Air Cleaner Resonator Outlet Duct Replacement. 2. Disconnect
More informationVehicle Level Engine, Cooling and Exhaust Engine Intake Manifold Service and Repair. Service and Repair
Page 1 of 11 Home Account Contact ALLDATA Log Out Help BILL SEIDLES MITSUBISHI Select Vehicle New TSBs Technician's Reference Component Search: OK 2005 Suzuki Verona L6-2.5L Conversion Calculator Vehicle
More informationIntake Manifold Removal and Installation
2004 Element Intake Manifold Removal and Installation Exploded View Removal Report a problem with this article 1. Disconnect the intake air temperature (IAT) sensor connector (A). 2. Remove the vacuum
More informationPage 1 of 8 SECTION 303-01A: Engine 2.3L 2002 Ranger Workshop Manual IN-VEHICLE REPAIR Procedure revision date: 10/20/2004 Intake Manifold Removal 1. Remove the accelerator control snow shield. 2. Remove
More informationVehicle Level Engine, Cooling and Exhaust Engine Cylinder Head Assembly Service and Repair. Service and Repair
Page 1 of 7 Home Account Contact ALLDATA Log Out Help BILL SEIDLES MITSUBISHI Select Vehicle New TSBs Technician's Reference Component Search: OK 2001 Pontiac Sunfire L4-2.2L VIN 4 Conversion Calculator
More information7. Remove the starter motor. Refer to Starter Motor Replacement (2.2L) or Starter Motor Replacement (4.3L).
1 of 9 1/5/2013 6:40 PM Removal Procedure 1. Disconnect the battery negative cable. Refer to Battery Replacement. 2. Remove the hood. Refer to Hood Replacement. 3. If the vehicle is equipped with a manual
More information2003 ACCORD - Intake Manifold Removal and Installation
2003 ACCORD - Intake Manifold Removal and Installation Exploded View '06-07 Models Removal ('03-05 Models) 1. Disconnect the intake air temperature (IAT) sensor connector (A). 2. Remove the vacuum hose
More information10/30/2018 Intake Manifold Replacement (RPOs LY2/LY6) 2007 GMC Truck Yukon Denali MotoLogic
2007 Yukon Denali Applies to: 4.8L, 5.3L, 6.0L and 6.2L Report a problem with this article Removal Procedure 1. Remove the air cleaner outlet duct. Refer to Air Cleaner Resonator Outlet Duct Replacement.
More informationREMOVAL. Fig Sized for Print
ALLDATA Online - 2000 Dodge Truck Grand Caravan FWD V6-3.3L VIN R - Intake M... Page 1 of 10 REMOVAL 1. Remove windshield wiper module. 2. Perform fuel system pressure release procedure (before attempting
More informationALLDATA Online Chevy Truck TrailBlazer 2WD L6-4.2L VIN S - Service and R... Service and Repair
Page 1 of 7 Home Account Contact ALLDATA Log Out Help PAUL REDEHOFT Select Vehicle New TSBs Technician's Reference Component Search: OK 2003 Chevy Truck TrailBlazer 2WD L6-4.2L VIN S Conversion Calculator
More informationALLDATA Online Cadillac DeVille V8-4.6L VIN Y - Lower Crankcase Installation. Lower Crankcase Installation
Page 1 of 7 Home Account Contact ALLDATA Log Out Help PAUL REDEHOFT Select Vehicle New TSBs Technician's Reference Component Search: OK 1998 Cadillac DeVille V8-4.6L VIN Y Conversion Calculator Vehicle
More information2000 Chrysler SEBRING
2000 Chrysler SEBRING Submodel: JX Engine Type: V6 Liters: 2.5 Fuel Delivery: FI Fuel: GAS 2.0L SOHC and 2.4L DOHC Engines The intake manifold for the 2.0L SOHC engine is a long branch design made of a
More informationALLDATA Online Hummer H2 V8-6.0L - Brake Pads Replacement - Rear. Brake Pads Replacement - Rear
Page 1 of 5 Home Account Contact ALLDATA Log Out Help PAUL REDEHOFT Select Vehicle New TSBs Technician's Reference Component Search: OK 2005 Hummer H2 V8-6.0L Conversion Calculator Vehicle Level Brakes
More information2003 RSX - Intake Manifold Removal and Installation
2003 RSX - Intake Manifold Removal and Installation Exploded View - K20A3 Engine Removal - K20A3 Engine 1. Remove the intake manifold cover. 2. Disconnect the intake air temperature (IAT) sensor connector
More informationIntake Manifold Removal
PLEASE READ ALL OF THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION. AT ANY TIME YOU DO NOT UNDERSTAND THE INSTRUCTIONS Parts included: -GT350 Intake manifold M-944-M5 -GT350 Air bucket w/filter.
More informationInstallation Instructions for: TOYOTA 4.5L SUPERCHARGER SYSTEM
Installation Instructions for: TOYOTA 4.5L SUPERCHARGER SYSTEM 1995-1997 Land Cruiser * PREMIUM FUEL REQUIRED * Magnuson Products LLC 1990 Knoll Drive, Bldg A, Ventura, CA 93003 (805) 642-8833 phone *
More information10/20/ Ford E 250 Engine Mechanical > Engine, 4.6L and 5.4L > IN VEHICLE REPAIR > Intake Manifold 5.4L
2005 Ford E 250 : Engine Mechanical > Engine, 4.6L and 5.4L > IN VEHICLE REPAIR > Intake Manifold 5.4L Intake Manifold 5.4L Listen SECTION 303 01A: Engine 4.6L and 5.4L 2005 E Series Workshop Manual IN
More informationIN-VEHICLE REPAIR. Upper Intake Manifold
303-01-1 Engine 3.9L and 4.2L 303-01-1 IN-VEHICLE REPAIR Upper Intake Manifold Special Tool(s) Remover, Spark Plug Wire 303-106 (T74P-6666-A) Material Item Silicone Brake Caliper Grease and Dielectric
More informationALLDATA Online - 1997 Ford Truck F 150 2WD Pickup V8-5.4L SOHC VIN L - Servi... Page 1 of 22 Home Account Contact ALLDATA Log Out Help BILL SEIDLES MITSUBISHI Select Vehicle New TSBs Technician's Reference
More information2011 Mercury Grand Marquis LS
Fig. 6: Locating Intake Manifold Crash Bracket With Tie Strap 24. Remove the intake manifold crash bracket bolt. 25. Disconnect the fuel rail pressure and temperature sensor vacuum and electrical connectors.
More informationFuel Injector Replacement (Right Bank) EN Injector Bore and Sleeve Cleaning Kit J Fuel Injector Removal Tool
Page 1 of 7 Home Account Contact ALLDATA Log Out Help DAN GRIMWOOD DAN GRIMWOOD00002 Select Vehicle New TSBs Technician's Reference Component Search: OK 2002 Chevy Truck C 2500 Truck 2WD V8-6.6L DSL Turbo
More informationREMOVAL & INSTALLATION
REMOVAL & INSTALLATION NOTE: For reassembly reference, label all electrical connectors, vacuum hoses and fuel lines before removal. Also place mating marks on engine hood and other major assemblies before
More informationENGINE ASSEMBLY STOCK TO 250 HP
GM SPORT COMPACT Performance Build Book 25 ENGINE ASSEMBLY STOCK TO 250 HP Fig. 3 The stock ECOTEC engine has proven reliable to 250 hp.(fig. 3) Performance upgrades are available from GM Performance Parts
More informationALLDATA Online Dodge Truck RAM 1500 Truck 2WD V6-3.7L VIN K - Steeri... Steering Column
Page 1 of 5 Home Account Contact ALLDATA Log Out Help PAUL REDEHOFT Select Vehicle New TSBs Technician's Reference Component Search: OK 2002 Dodge Truck RAM 1500 Truck 2WD V6-3.7L VIN K Conversion Calculator
More information1501 Industrial Way N., Toms River, NJ Fax: PACKING LIST
1/6/04 1501 Industrial Way N., Toms River, NJ 08755 732-349-2109 Fax:732-244-0867 MODERATE - Installation requires metric tools and possibly cutting and drilling. The ability to closely follow instructions
More informationHeater/Vent Module Replacement
Page 1 of 7 Home Account Contact ALLDATA Log Out Help BILL SEIDLES MITSUBISHI Select Vehicle New TSBs Technician's Reference Component Search: OK 2000 Chevy Truck S10/T10 P/U 2WD V6-4.3L VIN W Conversion
More informationAudi > B4 > Liter V6 2V Engine Mechanical, Engine Code(s): AAH, AFC 10 Engine Assembly
Audi > B4 > 1993 1995 2.8 Liter V6 2V Engine Mechanical, Engine Code(s): AAH, AFC 10 Engine Assembly Removing The engine is removed from above, after being separated from the transmission. Note: All tie
More informationDisconnect the APP sensor harness connector. See Fig. 4. Remove the accelerator pedal mounting nuts. Remove the APP assembly.
ENGINE CONTROLS - REMOVAL, OVERHAUL & INSTALLATION - 6.6L DIESEL... Page 1 of 41 FUEL SYSTEMS ACCELERATOR PEDAL POSITION SENSOR Removal & Installation Disconnect the APP sensor harness connector. See Fig.
More informationDisconnect negative battery cable and remove coolant bottle cap.
1 of 16 3/25/2012 10:18 AM ools Required SA9105E 3-Bar Engine Support Fixture SA9412G Constant Force Clamp Pliers SA9127E Gage Bar Set Powertrain Assembly Removal Caution: Do not allow smoking or the use
More informationINTAKE MANIFOLD COLLECTOR. 1. Electric throttle control actuator 2. Gasket 3. Vacuum hose
INTAKE MANIFOLD COLLECTOR Removal and Installation PFP:14003 ABS0095V 1. Electric throttle control actuator 2. Gasket 3. Vacuum hose 4. EVAP canister purge volume control solenoid valve 5. Bracket 6. Intake
More informationService and Repair. NOTE: Before proceeding, review all Steering Column and Airbag Warnings and Cautions.
ALLDATA Online - 2003 Chrysler Truck Town & Country V6-3.8L VIN L - Service and... Page 1 of 10 Home Account Contact ALLDATA Log Out Help BILL SEIDLES MITSUBISHI Select Vehicle New TSBs Technician's Reference
More informationLocations. Select Vehicle New TSBs Technician's Reference Isuzu Truck Rodeo LS 2WD V6-3.2L
1 of 4 5/16/2008 1:06 PM Home Account Contact ALLDATA Log Out Help Select Vehicle New TSBs Technician's Reference Component Search: METRO TOYOTA OK 2001 Isuzu Truck Rodeo LS 2WD V6-3.2L Conversion Calculator
More informationPage 1 of 6 Section 03-01C: Engine, 7.5L MFI 1996 Bronco/F-Series Workshop Manual IN-VEHICLE SERVICE Procedure revision date: 06/19/2000 Cylinder Heads Removal SPECIAL SERVICE TOOL(S) REQUIRED Description
More information1997 Volvo 850 GLT. Fig. 2: Removing Drive Shaft, Engine Mount Bolt & Torque Arm (5-Cylinder) Courtesy of VOLVO CARS OF NORTH AMERICA.
Fig. 2: Removing Drive Shaft, Engine Mount Bolt & Torque Arm (5-Cylinder) 4. Remove front exhaust pipe nuts and springs. Remove front exhaust pipe bolts. Disconnect speedometer. Remove engine mounting
More informationSTARTER COMPONENTS FOR REMOVAL AND INSTALLATION
Removal STARTER COMPONENTS FOR REMOVAL AND INSTALLATION Starter Components For Removal And Installation REMOVAL OF STARTER 1. DISCONNECT CABLE FROM NEGATIVE TERMINAL OF BATTERY CAUTION: Work must be started
More information2001 Lincoln LS Workshop Manual
Page 1 of 10 SECTION 303-01B: Engine 3.9L 2001 Lincoln LS Workshop Manual IN-VEHICLE REPAIR Procedure revision date: 05/16/2000 Intake Manifold Removal 1. Disconnect the battery ground cable. For additional
More informationPre-Installed. 1 Seal Kit 10 Silicone O-ring, 3/32 W, Intake Port Seals 1 Throttle Body Seal
Atomic AirForce Intake Manifold for LS7, 2006-2013 Corvette and 2014 Z28 Camaro - PN 2701 LS2, 2005-2007 Corvette and CTS-V, 2005-2006 GTO and SSR PN 2702 LS1/6*, 1997-2004 Corvette, 1998-2002 Camaro/Firebird,
More informationCylinder Head Replacement
CYLINDER HEAD REPLACEMENT (EN... CYLINDER HEAD REPLACEMENT (ENGINE MECHANICAL - 1.6L) Document ID# 1430093 Cylinder Head Replacement Tools Required J 45059 Angle Meter KM-470-B Angular Torque Gauge J 42492-A
More informationTurbo Boost Pressure Test
1 of 3 6/16/2008 9:07 PM Home Account Contact ALLDATA Log Out Help Select Vehicle New TSBs Technician's Reference Component Search: METRO TOYOTA OK 1992 Volvo 740 L4-2320cc 2.3L SOHC Turbo VIN 87 B230FT
More information1 of 12 10/5/2015 8:11 AM
1 of 12 10/5/2015 8:11 AM REMOVAL 1. Perform the fuel pressure release procedure See: Fuel Pressure Release > Procedures > Fuel System Pressure Release Procedure. 2. Recover the refrigerant from the refrigerant
More informationEngine Removal and Installation
Page 1 of 5 Home Account Contact ALLDATA Log Out Help TINO TORRES Select Vehicle New TSBs Technician's Reference Component Search: OK 2005 Chrysler Sebring Sedan V6-2.7L VIN R Conversion Calculator Vehicle
More informationALLDATA Online Dodge Truck RAM 1500 Truck 4WD V8-5.7L - Service and R... Page 1 of 10. Service and Repair
ALLDATA Online - 2009 Dodge Truck RAM 1500 Truck 4WD V8-5.7L - Service and R... Page 1 of 10 Home Account Contact ALLDATA Log Out Help PAUL REDEHOFT Select Vehicle New TSBs Technician's Reference Component
More information5.7L V Chevrolet Camaro * PLEASE READ THIS FIRST * ENGINE IDENTIFICATION VEHICLE IDENTIFICATION NUMBER (VIN) ADJUSTMENTS
5.7L V8 2001 Chevrolet Camaro 2000-01 ENGINES General Motors 5.7L V8 Chevrolet; Camaro Pontiac; Firebird * PLEASE READ THIS FIRST * NOTE: For engine repair procedures not covered in this article, see ENGINE
More informationLSX Intake Manifold. #54001 LSX (78mm Throttle Body) #54003 LSX (90mm Throttle Body)
LSX Intake Manifold #54001 LSX (78mm Throttle Body) #54003 LSX (90mm Throttle Body) Thank you for your purchase of the most innovative and powerful Gen III (LS1 and LS6) manifold ever developed. We are
More informationLChevrolet Camaro Supercharger Kit
PART #92000A Important Notes: 2010-2013 6.2LChevrolet Camaro Supercharger Kit The use of fuel additives (ie. octane boosters) is not recommended. There is a possibility that these chemicals can damage
More informationService and Repair. Fig. 1 Starter Motor Replacement
Motor / ALLDATA Online - 1995 Pontiac Firebird V6-204 4L VIN S... http://www.motoralldata.com/alldata/motor~v71595976~c21288~... 1 of 3 5/15/2008 10:45 PM Home Account Contact ALLDATA Log Out Help Select
More informationINTAKE MANIFOLD INSPECTION/REPLACEMENT
ATTACHMENT III Owner Notification Program 99M01 INTAKE MANIFOLD INSPECTION/REPLACEMENT AFFECTED VEHICLES: 1997 AND 1998 CROWN VICTORIA POLICE INTERCEPTOR VEHICLES WITH 4.6L SOHC ENGINES BUILT AT THE ST.
More information7-8 CHEVROLET AND GMC BLAZER JIMMY S10 SONOMA _U07.qxd 8/30/05 3:01 PM Page 8 BVC GMC CARS JCK/MJS/KJE 8/22/ S10P-C07
26770_U07.qxd 8/30/05 3:01 PM Page 8 7-8 06025-S10P-C07 06025-S10P-C08 26770_U07.qxd 8/30/05 3:01 PM Page 9 7-9 06025-S10P-C09 26770_U07.qxd 8/30/05 3:01 PM Page 10 7-10 06025-S10P-C10 26770_U07.qxd 8/30/05
More informationNOTE: Do not disassemble upper intake manifold from lower intake manifold unless replacement of one of the components is necessary.
Fig. 2: Lower Intake Manifold Bolt Tightening Sequence INTAKE MANIFOLD (UPPER) NOTE: Do not disassemble upper intake manifold from lower intake manifold unless replacement of one of the components is necessary.
More informationIN-VEHICLE SERVICING > VALVE COVER - RH
Page 1 of 20 Service Manual: ENGINE - 5.4L (3V)- F-150 & MARK LT IN-VEHICLE SERVICING > VALVE COVER - RH 2008 Ford Pickup 5.4L Eng F150 Material Item Specification Motorcraft Metal Surface Prep ZC-31 PAG
More information2003 Taurus/Sable Workshop Manual
Page 1 of 24 SECTION 303-01A: Engine 3.0L (2V) ASSEMBLY 2003 Taurus/Sable Workshop Manual Engine Special Tool(s) Piston Ring Compressor 303- D032 (D81L-6002-C) Camshaft Bearing Set 303-017 (T65L-6250-A)
More informationMAIN CONTROL VALVE BODY. Removal 1. Disconnect the battery cables. 2. Remove the battery and tray.
1 of 17 MAIN CONTROL VALVE BODY Removal 1. Disconnect the battery cables. 2. Remove the battery and tray. 3. Disconnect the breather tube and mass air flow (MAF) / intake air temperature (IAT) sensor.
More information2001 Ford Windstar ENGINES 3.8L V6 - VIN 4 - Windstar
COWL TOP VENT PANEL 1. Remove windshield wiper pivot arms. Remove cowl top vent panel retaining screws. Release cowl top vent panel retaining clips. Remove windshield wiper fluid hose. Remove cowl top
More informationWARNING. Atomic AirForce Intake Manifold for
Atomic AirForce Intake Manifold for LS7, 2006-2013 Corvette and 2014 Z28 Camaro - PN 2701 LS2, 2005-2007 Corvette and CTS-V, 2005-2006 GTO and SSR PN 2702 LS3/L99, 2008-2013 Corvette and 2010-2014 Camaro
More informationOn Board Diagnostics II A PCED
Page 1 of 5 1998 PCED On Board Diagnostics II A SECTION 5A: Pinpoint Tests KE: Idle Air Control (IAC) Valve KE: Introduction KE1 IDLE CONCERNS OR STALLS: RUN KOER SELF-TEST AND OUTPUT CONTINUOUS MEMORY
More informationPage 1 of 6 Fuel Charging and Controls - Turbocharger - 2.7L V6 - TdV6 - Turbocharger RH Removal and Installation Special Tool(s) Engine support beam 303-021 Engine lifting brackets 303-1129 Removal 1.
More informationINTAKE AIR TEMPERATURE SENSOR (IAT)
INTAKE AIR TEMPERATURE SENSOR (IAT) 4.8 Refer to the ELECTRICAL DIAGNOSTIC MANUAL for information on the function and testing of the intake air temperature sensor (IAT sensor). sm054 To prevent accidental
More informationREMOVAL. 5. REMOVE OIL DIPSTICK GUIDE (a) Remove the bolt, dipstick guide and engine wire bracket. (b) Remove the O ring from the dipstick guide.
EM34 ENGINE MECHANICAL (2RZFE, 3RZFE) P23426 EM1MY01 REMOVAL 1. DRAIN ENGINE COOLANT 2. DISCONNECT THESE CABLES: (a) Disconnect the accelerator cable from the throttle body. A/T: Disconnect the throttle
More informationWARNING: ALWAYS relieve fuel pressure before disconnecting any fuel related component. DO NOT allow fuel to contact engine or electrical components.
4.0L V8 - VINS [K,U] Selected Block 1990 Lexus LS 400 For Lextreme Powertrain 2020 S. Hacienda Blvd. # D Hacienda Heights California 91745 Copyright 1998 Mitchell Repair Information Company, LLC Friday,
More informationALLDATA Online Chevy Truck Avalanche WD V8-5.3L VIN T - Steering... Page 1 of 12. Steering Wheel Module Coil Replacement (Coil)
ALLDATA Online - 2006 Chevy Truck Avalanche 1500 2WD V8-5.3L VIN T - Steering... Page 1 of 12 Steering Wheel Module Coil Replacement (Coil) INFLATABLE RESTRAINT STEERING WHEEL MODULE COIL REPLACEMENT (COIL)
More informationM-9424-M50B 2012 Boss 302 Intake Manifold INSTALLATION INSTRUCTIONS
!!! PLEASE READ ALL OF THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION. WARNING: CUSTOM CALIBRATION REQUIRED! CALIBRATION NOT INCLUDED! KIT CONTENTS: 1) Intake Manifold Assembly 2) Assembly
More informationALLDATA Online Honda Accord EX Sedan V6-3.0L - Recall - DTC P0401 EGR...Page 1 of 11
ALLDATA Online - 1999 Honda Accord EX Sedan V6-3.0L - Recall - DTC P0401 EGR...Page 1 of 11 99-085 October 26, 2001 * Applies To: 1998-00 Accord V6 - ALL 2001 Accord V6-4-door from VIN 1HGCG1...1A000001
More informationSHORT RAM SYSTEM. Installation Instructions for: Part Number Toyota Tacoma 4 Cyl Toyota 4Runner 4 Cyl.
SHORT RAM SYSTEM Installation Instructions for: Part Number 22-463 1995-1999 Toyota Tacoma 4 Cyl. 1996-1999 Toyota 4Runner 4 Cyl. ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit A Hawthorne, CA.
More informationIntake Manifold Replacement
Page 1 of 13 Your Current Vehicle: 2008 Cadillac STS Intake Manifold Replacement Intake Manifold Replacement Removal Procedure 1. Turn the ignition OFF. 2. Remove the fuel injector sight shield. Refer
More informationDISCONNECT CABLE FROM NEGATIVE TERMINAL OF BATTERY DISCONNECT CAM POSITION SENSOR CONNECTOR
1 of 12 4/26/2008 1:50 PM Home Account Contact ALLDATA Log Out Help Select Vehicle New TSBs Technician's Reference Component Search: METRO TOYOTA OK 1987 Toyota Supra L6-3.0L DOHC Turbo (7M-GTE) Conversion
More informationWARNING. 1 Seal Kit 10 Silicone O-ring, 3/32 W, Intake Port Seals 1 Throttle Body Seal
Atomic AirForce Intake Manifold for LS7, 2006-2013 Corvette and 2014 Z28 Camaro - PN 2701, PN 27013 (Black), PN 27014 (Gray) LS2, 2005-2007 Corvette and CTS-V, 2005-2006 GTO and SSR PN 2702, PN 27023 (Black),
More informationService Bulletin Cars
Volvo Cars of North America, Inc Rockleigh, New Jersey. Service Bulletin Cars SECTION GROUP NO. DATE 2 28 821 Aug. 1996 Replacing knock sensor (KS) 850 Turbo 1994 Page 1 of 9 REFERENCE: TP 2101201, SECTION
More informationPage 1 of 14 Oil Pan Removal & Installation 4.2L Engine 4WD Vehicles To Remove: 1. Before servicing the vehicle refer to the precautions at the beginning of this section. 2. Raise and support the vehicle.
More information2. Remove the intake manifold cover. Refer to Intake Manifold Cover Replacement.
VALVE COVER GASKET Valve Rocker Arm Cover Replacement - Left Side Removal Procedure 1. Partially drain the cooling system. Refer to Cooling System Draining and Filling (LZE, LZ4, LZG, 9C1, 9C3, GE47716
More informationDESCRIPTION Chevrolet Chevy Van 5.7L Eng G20. Service Manual: FUEL INJECTION SYSTEM - TBI
Service Manual: FUEL INJECTION SYSTEM - TBI DESCRIPTION 1989 Chevrolet Chevy Van 5.7L Eng G20 The throttle body fuel injection system consists of 7 major sub-assemblies: fuel supply system, throttle body
More informationPerfect Performance Products, LLC
PERFECT HI-VELOCITY 68MM THROTTLE BODY Installation Instructions Part # 65301 1991-1998 Jeep 4.0L Engines w/perfect Engine Management System P/N 65140, 65141 OR All Jeep 4.0L Engines in Cherokee, Grand
More informationDocument ID: General Motors Corporation. All rights reserved.
Page 1 of 7 Document ID: 1274962 #02-06-01-016A: (MIL) Service Engine Soon Telltale Illuminated With DTCs P0171 and/or P0174 (Retorque Intake Manifold Vacuum Chamber Bolts, Install Vacuum Chamber Springs)
More informationCOMPONENT LOCATOR > DISASSEMBLED VIEWS
Page 1 of 45 2006 Pontiac Grand Prix 3.8L Eng Base Service Manual: ENGINE MECHANICAL - 3.8L COMPONENT LOCATOR > DISASSEMBLED VIEWS Fig 1: Engine Block Component Views Callout Component Name 100 Engine
More informationCylinder Head Installation - Left Side
Cylinder Head Installation - Left Side Tools Required J 36660-A Torque Angle Meter 1. Install the cylinder head locator dowel pins, if necessary. 2. Inspect the cylinder head locator dowel pins for proper
More information2004 Volvo C70 L5-2.4L Turbo VIN 63 B5244T7 Cylinder Head Assembly Service and Repair, Removal and Replacement: Cylinder Head/Gasket, Replacing
1 of 25 8/18/2011 6:10 PM 2004 Volvo C70 L5-2.4L Turbo VIN 63 B5244T7 Cylinder Head Assembly Service and Repair, Removal and Replacement: Cylinder Head/Gasket, Replacing Cylinder head/gasket, replacement
More information2006 Honda Civic SI Supercharger Kit Installation Instruction Kit #
2006 Honda Civic SI Supercharger Kit Installation Instruction Kit #350-091 3239 MONIER CIRCLE, STE.5 RANCHO CORDOVA, CA 95742 916.635.4550 FAX 916.635.4632 www.ct-engineering.com INS-157 VERSION: 3.25.2009
More informationM-9424-M50CJ INTAKE MANIFOLD INSTALLATION INSTRUCTIONS
Please visit www.fordracingparts.com for the most current instruction information!!! PLEASE READ ALL OF THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION. AT ANY TIME YOU DO NOT UNDERSTAND THE
More information1. Install clean paper and/or shop towels between the electronic brake control module assembly (EBCM) and the inner fender.
Electronic Brake Control Module (EBCM) Replacement Removal Procedure Caution: Refer to Brake Fluid Irritant Caution in Service Precautions. Notice: Refer to Brake Fluid Effects on Paint and Electrical
More informationINSTALLATION INSTRUCTIONS PART NUMBER:
Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 22-463 1997-1999 TOYOTA Tacoma L4-2.7L C.A.R.B. E.O. # D-392-18 1997-1999 TOYOTA Tacoma L4-2.4L C.A.R.B. E.O. #
More information2004 Honda ELEMENT. Submodel: Engine Type: L4 Liters: 2.4 Fuel Delivery: FI Fuel: GAS. Engine Installation. Special Tools Required
2004 Honda ELEMENT Submodel: Engine Type: L4 Liters: 2.4 Fuel Delivery: FI Fuel: GAS Engine Installation Special Tools Required Engine hanger/adapter VSB02C000015 Engine support hanger, A & Reds AAR-T-12566
More information2003 Nissan-Datsun Truck Frontier 4WD V6-3.3L (VG33E)
1 of 15 8/7/2016 2:34 PM 2003 Nissan-Datsun Truck Frontier 4WD V6-3.3L (VG33E) Vehicle» Engine, Cooling and Exhaust» Engine» Cylinder Head Assembly» Service and Repair» Removal and Installation 2 of 15
More information1988 Ford F-350 PICKUP
1988 Ford F-350 PICKUP Submodel: Engine Type: V8 Liters: 7.5 Fuel Delivery: FI Fuel: GAS 1987 93 4.9L Engine The intake and exhaust manifolds on these engines are known as combination manifolds and are
More informationFUEL PRESSURE REGULATOR
EG2214 3VZE ENGINE FUEL PRESSURE REGULATOR ONVEHICLE INSPECTION CHECK FUEL PRESSURE (See step 2 on page EG2206) COMPONENTS FOR REMOVAL AND INSTALLATION FUEL PRESSURE REGULATOR REMOVAL 1. DISCONNECT NEGATIVE
More information1996 Aerostar/Ranger/Explorer
Page 1 of 11 Section 03-01B: Engine, 3.0L V-6 IN-VEHICLE SERVICE 1996 Aerostar and Ranger Vehicles Workshop Manual Water Pump SPECIAL SERVICE TOOL(S) REQUIRED Description Tool Number Fan Clutch Holding
More informationInstallation Instructions for: TOYOTA 3.4L SUPERCHARGER SYSTEM
Installation Instructions for: TOYOTA 3.4L SUPERCHARGER SYSTEM 1996-2002 4Runner 1997-1998 T100 1997-2004 Tacoma 2000-2003 Tundra * PREMIUM FUEL REQUIRED * Magnuson Products LLC 1990 Knoll Drive, Bldg
More information2002 Mustang Workshop Manual
Page 1 of 13 SECTION 303-01B: Engine 4.6L (2V) 2002 Mustang Workshop Manual REMOVAL Procedure revision date: 01/02/2003 Cylinder Heads Special Tool(s) Remover, Crankshaft Vibration Damper 303-009 (T58P-6316-D)
More information1. With the vehicle in NEUTRAL, position it on a hoist. For additional information, refer to Section
SECTION 303-01C: Engine 5.4L (4V) 2009 Mustang Workshop Manual REMOVAL Procedure revision date: 07/25/2008 Engine Special Tool(s) Heavy Duty Floor Crane 014-00071 or equivalent Lifting Bracket, Engine
More informationDTC P0172 Fuel Trim System Rich
Page 1 of 6 1997 Chevrolet Cavalier Cavalier, Sunfire (VIN J) Service Manual Document ID: 47788 DTC P0172 Fuel Trim System Rich System Description A Closed Loop air/fuel metering system is used to provide
More informationAssembly. NOTE: Before beginning assembly, perform/inspect the following:
Page 1 of 31 Home Account Contact ALLDATA Log Out Help DAN GRIMWOOD DAN GRIMWOOD00002 Select Vehicle New TSBs Technician's Reference Component Search: OK 1997 Ford Truck F 150 2WD Pickup V6-4.2L VIN 2
More informationINTAKE AND EXHAUST 15-1 CONTENTS SERVICE ADJUSTMENT PROCEDURES... 2 EXHAUST MANIFOLD EXHAUST PIPE AND MAIN MUFFLER...
I i 15-1 INTAKE AND EXHAUST CONTENTS 110003071 L AIR CLEANER 4.5L Engine>....3 AIR CLEANER 4.8L Engine>....4 EXHAUST MANIFOLD... 10 EXHAUST PIPE AND MAIN MUFFLER... 13 GENERAL INFORMATION.... 2 INTAKE
More information1 of 13 2/10/2016 6:46 PM
1 of 13 2/10/2016 6:46 PM # 12-06-04-003A: Malfunction Indicator Lamp (MIL) Illuminated, Reduced Engine Power Message Displayed, DTC P2135 Set - (Mar 24, 2014) Subject: Malfunction Indicator Lamp (MIL)
More informationFREE $15 Gift Card for every $100 spent on Ship To Home orders. Find Out How
1 of 29 10/12/2011 5:05 PM FREE $15 Gift Card for every $100 spent on Ship To Home orders. Find Out How Ford Ranger/Explorer/Mountaineer 1991-1999 Intake Manifold REMOVAL & INSTALLATION Print The engines
More informationChevy Sonic 1.4L Intake Manifold
Chevy Sonic 1.4L Intake Manifold Install Time: 3 hours In the Box: (1) Racer X Intake manifold (6) M8x1.25 bolts (4) M6x1 bolts (2) 1/8 NPT plugs (1) 3/8 NPT plug (1) 1/4 NPT 90 degree barb (4) Small O-rings
More information